Upgrading the Switch Software
For information about upgrading the switch software from Cisco IOS XE Release 3.x.x to Cisco IOS XE Denali 16.1.x, see Release Notes for Cisco Catalyst 3850 Series Switch, Cisco IOS XE Denali 16.1.x.
-
- IP Multicast Routing Technology Overview
- Configuring IGMP
- Configuring IGMP Proxy
- Constraining IP Multicast in Switched Ethernet
- Configuring Protocol Independent Multicast (PIM)
- Configuring PIM MIB Extension for IP Multicast
- Configuring MSDP
- Configuring Wireless Multicast
- Configuring SSM
- Configuring Multicast Routing over GRE Tunnel
- Configuring the Service Discovery Gateway
- IP Multicast Optimization: Optimizing PIM Sparse Mode in a Large IP Multicast Deployment
- IP Multicast Optimization: Multicast Subsecond Convergence
- IP Multicast Optimization: IP Multicast Load Splitting across Equal-Cost Paths
- IP Multicast Optimization: SSM Channel Based Filtering for Multicast
- IP Multicast Optimization: PIM Dense Mode State Refresh
- IP Multicast Optimization: IGMP State Limit
-
- Configuring the Device for Access Point Discovery
- Configuring Data Encryption
- Configuring Retransmission Interval and Retry Count
- Configuring Adaptive Wireless Intrusion Prevention System
- Configuring Authentication for Access Points
- Converting Autonomous Access Points to Lightweight Mode
- Using Cisco Workgroup Bridges
- Configuring Probe Request Forwarding
- Optimizing RFID Tracking
- Country Codes
- Configuring Link Latency
- Configuring Power over Ethernet
-
- Configuring Autoconf
- Configuring Cisco IOS Configuration Engine
- Configuring the Cisco Discovery Protocol
- Configuring Simple Network Management Protocol
- Configuring Service Level Agreements
- Configuring Local Policies
- Configuring SPAN and RSPAN
- Configuring ERSPAN
- Configuring Packet Capture
- Configuring Flexible NetFlow
-
- Preventing Unauthorized Access
- Controlling Switch Access with Passwords and Privilege Levels
- Configuring TACACS+
- MACsec Encryption
- Configuring RADIUS
- Configuring RADIUS over DTLS
- Configuring Kerberos
- Configuring Local Authentication and Authorization
- Configuring Secure Shell
- X.509v3 Certificates for SSH Authentication
- Configuring Secure Socket Layer HTTP
- IPv4 ACLs
- IPv6 ACLs
- Configuring DHCP
- Configuring IP Source Guard
- Configuring Dynamic ARP Inspection
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring Device Sensor
- Web-Based Authentication
- Configuring Port-Based Traffic Control
- Configuring IPv6 First Hop Security
- Configuring SISF-Based Device Tracking
- Configuring Cisco TrustSec
- Configuring Control Plane Policing
- Configuring Wireless Guest Access
- Managing Rogue Devices
- Classifying Rogue Access Points
- Configuring wIPS
- Configuring Intrusion Detection System
-
- Administering the Switch
- Boot Integrity Visibility
- Performing Device Setup Configuration
- Configuring Autonomic Networking
- Configuring Right-To-Use Licenses
- Configuring Administrator Usernames and Passwords
- 802.11 parameters and Band Selection
- Configuring Aggressive Load Balancing
- Configuring Client Roaming
- Configuring Application Visibility and Control in a Wired Network
- Configuring Application Visibility and Control in a Wireless Network
- Configuring Location Settings
- Configuring Voice and Video Parameters
- Configuring RFID Tag Tracking
- Configuring Location Settings
- Cisco Hyperlocation
- Monitoring Flow Control
- Configuring SDM Templates
- Configuring System Message Logs
- Configuring Online Diagnostics
- Managing Configuration Files
- Configuration Replace and Configuration Rollback
- Working with the Flash File System
- Upgrading the Switch Software
- Conditional Debug and Radioactive Tracing
- Troubleshooting the Software Configuration
Feedback