Cisco Nexus 9000 ACI-Mode Switches Release Notes, Release 12.3(1)

July 6, 2021

In the Supported Hardware section, added the NXA-PAC-500W-PI and NXA-PAC-500W-PE PSUs.

June 24, 2021

Added open issue CSCvu07844.

January 19, 2021

In the Known Behaviors section, changed the following sentence:

The Cisco Nexus 9508 ACI-mode switch supports warm (stateless) standby where the state is not synched between the active and the standby supervisor modules.

To:

The modular chassis Cisco ACI spine nodes, such as the Cisco Nexus 9508, support warm (stateless) standby where the state is not synched between the active and the standby supervisor modules.

March 13, 2020

12.3(1e): In the Resolved Bugs section, added bug CSCvr98827.

September 20, 2019

In the Usage Guidelines section, added the following bullet:

■      A 25G link that is using the IEEE-RS-FEC mode can communicate with a link that is using the CL16-RS-FEC mode. There will not be a FEC mismatch and the link will not be impacted.

September 11, 2019

In the Supported Hardware section, for the N9K-C93108TC-FX and N9K-C93180YC-FX switches, added the following note:

Note: Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

August 14, 2019

12.3(1e): In the Open Bugs section, added bug CSCvp92269.

August 6, 2019

12.3(1e): In the Resolved Bugs section, added bug CSCvm96490.

July 31, 2019

In the Compatibility Information section, added the following bullet:

■      On Cisco ACI platforms, 25G copper optics do not honor auto-negotiation, and therefore auto-negotiation on the peer device (ESX or standalone) must be disabled to bring up the links.

January 30, 2019

12.3(1e): In the Open Bugs section, added bug CSCvn69340.

June 19, 2018

12.3(1p): Release 12.3(1p) became available. Added the resolved bugs for this release.

June 7, 2018

12.3(1e): In the Open Bugs section, added bug CSCvg35892.

April 24, 2018

12.3(1e): In the Open Bugs section, added bug CSCvi57920.

February 23, 2018

12.3(1o): Release 12.3(1o) became available. Added the resolved bugs for this release.

January 22, 2018

12.3(1l): Release 12.3(1l) became available. Added the resolved bugs for this release.

December 11, 2017

12.3(1e): Moved bug CSCvd80766 from the Open Bugs section to the Known Behaviors section.

December 6, 2017

12.3(1e): In the Know Behaviors section, added bug CSCvd63567.

November 3, 2017

12.3(1e): In the Open Bugs section, added bug CSCve65374.

October 20, 2017

12.3(1i): Release 12.3(1i) became available. Added the open and resolved bugs for this release.

July 9, 2017

12.3(1f): Release 12.3(1f) became available; there are no changes to this document for this release.

June 16, 2017

12.3(1e): Added bug CSCve82313 to Resolved Bugs.

June 14, 2017

12.3(1e): Release 12.3(1e) became available.

Chassis

N9K-C9504

Cisco Nexus 9504 chassis with 4 I/O slots

Chassis

N9K-C9508

Cisco Nexus 9508 chassis with 8 I/O slots

Chassis component

N9K-C9508-FAN

Fan tray

Chassis component

N9k-PAC-3000W-B

Cisco Nexus 9500 3000W AC power supply, port side intake

Pluggable module (GEM)

N9K-M12PQ

12-port or 8-port

Pluggable module (GEM)

N9K-M6PQ

6-port

Pluggable module (GEM)

N9K-M6PQ-E

6-port, 40 Gigabit Ethernet expansion module

Spine switch

N9K-C9336PQ

Cisco Nexus 9336PQ switch, 36-port 40 Gigabit Ethernet QSFP

Spine switch

N9K-C9508-B1

Cisco Nexus 9508 chassis bundle with 1 supervisor module, 3 power supplies, 2 system controllers, 3 fan trays, and 3 fabric modules

Spine switch

N9K-C9508-B2

Cisco Nexus 9508 chassis bundle with 1 supervisor module, 3 power supplies, 2 system controllers, 3 fan trays, and 6 fabric modules

Spine switch

N9K-C9516

Cisco Nexus 9516 switch with 16 line card slots

Spine switch fan

N9K-C9300-FAN3

Port side intake fan

Spine switch fan

N9K-C9300-FAN3-B

Port side exhaust fan

Spine switch module

N9K-C9504-FM

Cisco Nexus 9504 fabric module supporting 40 Gigabit line cards

Spine switch module

N9K-C9504-FM-E

Cisco Nexus 9504 fabric module supporting 100 Gigabit line cards

Spine switch module

N9K-C9508-FM

Cisco Nexus 9508 fabric module supporting 40 Gigabit line cards

Spine switch module

N9K-C9508-FM-E

Cisco Nexus 9508 Fabric module supporting 100 Gigabit line cards

Spine switch module

N9K-X9732C-EX

Cisco Nexus 9500 32-port, 40/100 Gigabit Ethernet QSFP28 aggregation module

Spine switch module

N9K-X9736PQ

Cisco Nexus 9500 36-port, 40 Gigabit Ethernet QSFP aggregation module

Switch module

N9K-SC-A

Cisco Nexus 9500 Series system controller

Switch module

N9K-SUP-A

Cisco Nexus 9500 Series supervisor module

Switch module

N9K-SUP-A+

Cisco Nexus 9500 Series supervisor module

Switch module

N9K-SUP-B

Cisco Nexus 9500 Series supervisor module

Switch module

N9K-SUP-B+

Cisco Nexus 9500 Series supervisor module

Top-of-rack (ToR) leaf switch

N9K-C93108TC-EX

Cisco Nexus 9300 platform switch with 48 1/10GBASE-T (copper) front panel ports and 6 40/100-Gigabit QSFP28 spine facing ports.

Top-of-rack (ToR) leaf switch

N9K-C93108TC-FX

Cisco Nexus 9300 platform switch with 48 1/10GBASE-T (copper) front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports.

Note: Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

Top-of-rack (ToR) leaf switch

N9K-C93120TX

Cisco Nexus 9300 platform switch with 96 1/10GBASE-T (copper) front panel ports and 6-port 40-Gigabit Ethernet QSFP spine-facing ports

Top-of-rack (ToR) leaf switch

N9K-C93128TX

Cisco Nexus 9300 platform switch with 96 1/10GBASE-T (copper) front panel ports and 6 or 8 40-Gigabit Ethernet QSFP spine-facing ports

Top-of-rack (ToR) leaf switch

N9K-C93180LC-EX

Cisco Nexus 9300 platform switch with 24 40-Gigabit front panel ports and 6 40/100-Gigabit QSFP28 spine-facing ports

The switch can be used either 24 40G ports or 12 100G ports. If 100G is connected the Port1, Port 2 will be HW disabled.

Note: This switch has the following limitations:

·       This release does not support 1 Gbps for QSA.

·       The top and bottom ports must use the same speed. If there is a speed mismatch, the top port takes precedence and bottom port will be error disabled. Both ports both must be used in either the 40 Gbps or 10 Gbps mode.

·       Ports 26 and 28 are hardware disabled.

·       This release supports 40 and 100 Gbps for the front panel ports. The uplink ports can be used at the 100 Gbps speed.

Top-of-rack (ToR) leaf switch

N9K-C93180YC-EX

Cisco Nexus 9300 platform switch with 48 1/10/25-Gigabit front panel ports and 6-port 40/100 Gigabit QSFP28 spine-facing ports

Top-of-rack (ToR) leaf switch

N9K-C93180YC-FX

Cisco Nexus 9300 platform switch with 48 1/10/25-Gigabit Ethernet SFP28 front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports. The SFP28 ports support 1-, 10-, and 25-Gigabit Ethernet connections and 8-, 16-, and 32-Gigabit Fibre Channel connections.

Note: Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

Top-of-rack (ToR) leaf switch

N9K-C9332PQ

Cisco Nexus 9332PQ Top-of-rack (ToR) Layer 3 switch with 26 APIC-facing ports and 6 fixed-Gigabit spine facing ports.

Top-of-rack (ToR) leaf switch

N9K-C9372PX

Cisco Nexus 9372PX Top-of-rack (ToR) Layer 3 switch with 48 Port 1/10-Gigabit APIC-facing ports Ethernet SFP+ front panel ports and 6 40-Gbps Ethernet QSFP+ spine-facing ports

Note: Only the downlink ports 1-16 and 33-48 are capable of supporting SFP1-10G-ZR SFP+.

Top-of-rack (ToR) leaf switch

N9K-C9372PX-E

Cisco Nexus 9372PX-E Top-of-rack (ToR) Layer 3 switch with 48 Port 1/10-Gigabit APIC-facing ports Ethernet SFP+ front panel ports and 6 40-Gbps Ethernet QSFP+ spine-facing ports

Note: Only the downlink ports 1-16 and 33-48 are capable of supporting SFP1-10G-ZR SFP+.

Top-of-rack (ToR) leaf switch

N9K-C9372TX

Cisco Nexus 9372TX Top-of-rack (ToR) Layer 3 switch with 48 1/10GBASE-T (copper) front panel ports and 6 40-Gbps Ethernet QSFP spine-facing ports

Top-of-rack (ToR) leaf switch

N9K-C9372TX-E

Cisco Nexus 9372TX-E Top-of-rack (ToR) Layer 3 switch with 48 10GBASE-T (copper) front panel ports and 6 40-Gbps Ethernet QSFP+ spine-facing ports

Top-of-rack (ToR) leaf switch

N9K-C9396PX

Cisco Nexus 9300 platform switch with 48 1/10-Gigabit SFP+ front panel ports and 6 or 12 40-Gigabit Ethernet QSFP spine-facing ports  

Top-of-rack (ToR) leaf switch

N9K-C9396TX

Cisco Nexus 9300 platform switch with 48 1/10GBASE-T (copper) front panel ports and 6 or 12 40-Gigabit Ethernet QSFP spine-facing ports

Top-of-rack (ToR) leaf switch fan

NXA-FAN-30CFM-B

Red port side intake fan

Top-of-rack (ToR) leaf switch fan

NXA-FAN-30CFM-F

Blue port side exhaust fan

Top-of-rack (ToR) leaf switch power supply unit

N9K-PAC-1200W

1200W AC Power supply, port side intake pluggable

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches

Top-of-rack (ToR) leaf switch power supply unit

N9K-PAC-1200W-B

1200W AC Power supply, port side exhaust pluggable

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches

Top-of-rack (ToR) leaf switch power supply unit

N9K-PAC-650W

650W AC Power supply, port side intake pluggable

Top-of-rack (ToR) leaf switch power supply unit

N9K-PAC-650W-B

650W AC Power supply, port side exhaust pluggable

Top-of-rack (ToR) leaf switch power supply unit

N9K-PUV-1200W

1200W HVAC/HVDC dual-direction airflow power supply

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches

Top-of-rack (ToR) leaf switch power supply unit

N9K-PUV-3000W-B

3000W AC Power supply, port side exhaust pluggable

Top-of-rack (ToR) leaf switch power supply unit

NXA-PAC-1200W-PE

1200W AC Power supply, port side exhaust pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches.

Top-of-rack (ToR) leaf switch power supply unit

NXA-PAC-1200W-PI

1200W AC Power supply, port side intake pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches.

Top-of-rack (ToR) leaf switch power supply unit

NXA-PAC-500W-PE

500W AC Power supply, port side exhaust pluggable

Top-of-rack (ToR) leaf switch power supply unit

NXA-PAC-500W-PI

500W AC Power supply, port side intake pluggable

Top-of-rack (ToR) leaf switch power supply unit

UCSC-PSU-930WDC V01

Port side exhaust DC power supply compatible with all ToR leaf switches

Top-of-rack (ToR) leaf switch power supply unit

UCS-PSU-6332-DC

930W DC power supply, reversed airflow (port side exhaust)

N2K-B22DELL-P

B22 FEX for Dell

N2K-B22HP-P

B22 FEX for HP

N2K-B22IBM-P

B22 FEX for IBM

N2K-C2248PQ-10GE

Cisco Nexus 2248PQ 10GE Fabric Extender, 2PS, 4 Fan Module, 48x1/10GE (req SFP/SFP+) + 4x40G QSFP+(req QSFP+), choice of airflow and power supply

N2K-C2248TP-1GE

Cisco Nexus 2248TP Series 1GE Fabric Extender, 2 AC PS, 1 Fan Module (Standard Airflow/port side exhaust), 48x100/1000Base-T + 4x10GE (req SFP+), same as N2K-C2248TP

N2K-C2248TP-E-1GE

Cisco Nexus 2248TP-E Series 1GE Fabric Extender, 2PS, 1 Fan Module, 48x100/1000Base-T + 4x10GE (req SFP+), 32MB buffer, choice of airflow and power supply

N2K-C2332TQ

Cisco Nexus 2332TQ 10G BASE T Fabric Extender, 2PS, 3 Fan Module, 48x100M/1/10GE + 4x40G QSFP+(req QSFP+), choice of airflow and power supply

N2K-C2348TQ

Cisco Nexus 2348TQ 10G BASE T Fabric Extender, 2PS, 3 Fan Module, 48x100M/1/10GE + 6x40G QSFP+(req QSFP+), choice of airflow and power supply

N2K-C2348UPQ

48 100Mῖ/1/10 Gigabit Ethernet and Unified Port host interfaces (SFP+) and up to 6ῖ QSFP+ 10/40 Gigabit Ethernet fabric interfaces

N2K-C2232PP-10GE

Cisco Nexus 2232PP Series 10GE Fabric Extender, 2 AC PS, 1 Fan Module (Standard Airflow/port side exhaust), 32x1/10GE (req SFP/SFP+) + 8x10GE (req SFP+), same as N2K-C2232PP

N2K-C2232TM-E-10GE

Cisco Nexus 2232TM-E Series 10GBASE-T Fabric Extender, 2PS, 1 Fan Module, 32x1/10GBase-T + 8x10GE Module (req SFP+), choice of airflow and power supply

CSCvj50973

When the MTU settings for OSPF neighboring router interfaces do not match, the routers will be stuck in the Exstart/Exchange state. This behavior is expected. This bug is an enhancement to raise a fault to the APIC so that the routers' stuck state can be easily detected by the administrator.

12.3(1o) and later

CSCvc17015

Quick changes in the RPF interface trigger RPF lookups in MRIB and PIM for all of the routes, which results in a high convergence time.

12.3(1e) and later

CSCvd39719

Ping packets cannot be sent from spine1 (of pod1) to spine2 (of pod2) with MTU set to greater than 1350, irrespective of the control plane MTU value.

12.3(1e) and later

CSCvd63567

After upgrading a switch, Layer 2 multicast traffic flowing across PODs gets affected for some of the bridge domain Global IP Outsides.

12.3(1e) and later

CSCvd66411

When VPC and Bidirectional Forwarding Detection (BFD) are deployed on some ToR platforms, BFD might flap on an interface shut/no-shut of one leg of the VPC.

12.3(1e) and later

CSCve06334

MAC and IP endpoints are not learned on the local vPC pair.

12.3(1e) and later

CSCve65374

Traffic that flows toward some tunnel endpoints (TEPs) will be dropped. This issue occurs because the tunnel toward those TEPs is programmed with drop adjacency.

12.3(1e) and later

CSCve79295

The CoPP rate/burst might get set to the default values when the CoPP policy is changed.

12.3(1e) and later

CSCvf09313

In the 12.2(2i) release, the BPDU filter only prevents interfaces from sending BPDUs, but does not prevent interfaces from receiving BPDUs.

12.3(1e) and later

CSCvg35892

There is a delay in internal process communication of over a minute due to a timeout (timeout period is 60 seconds). This can manifest itself in different ways. In one way, the Policy Element sent a delete/create request for a VLAN to the VLAN manager, but the VLAN manager did not process the request until the initial request timed out. This resulted in an outage that lasted a little over a minute while changing a BD from Unknown Unicast Flood to Hardware Proxy.

12.3(1e) and later

CSCvi57920

A UCS 1225 vNIC goes down after changing the peer Cisco ACI leaf node name.

12.3(1e) and later

CSCvn69340

The BFD session does not get instantiated under some circumstances in one of the VPC legs for static routes.

12.3(1e) and later

CSCvp50075

A leaf switch experiences an unexpected reload due to a HAP reset.

12.3(1e) and later

CSCvp92269

Running a Qualys security scan results in the following message:

CWE - 693 Protection Mechanism Failure -

"HTTP Security Header Not Detected"

12.3(1e) and later

CSCvr98827

Some of the control plane packets are incorrectly classified as the user class and are reported as dropped in single chip spine switches. The statistics are incorrect because the packets are not actually dropped.

12.3(1e) and later

CSCvs18150

After a certain set of steps, it is observed that the deny-external-tag route-map used for transit routing loop prevention gets set back to the default tag 4294967295. Since routes arriving in Cisco ACI with this tag are denied from being installed in the routing table, if the VRF table that has the route-tag policy is providing transit for another VRF table in Cisco ACI (for instance and inside and outside VRF with a firewall connecting them) and the non-transit VRF table has the default route-tag policy, routes from the non-transit VRF table would not be installed in the transit VRF table.

This bug is also particularly impactful in scenarios where transit routing is being used and OSPF or EIGRP is used on a vPC border leaf switch pair. vPC border leaf switches peer with each other, so if member A gets a transit route from BGP, redistributes into OSPF, and then advertises to member B (since they are peers)...without a loop prevention mechanism, member B would install the route through OSPF since it has a better admin distance and would then advertise back into BGP. This VRF tag is set on redistribution of BGP > OSPF and then as a table map in OSPF that blocks routes with the tag from getting installed in the routing table. When hitting this bug, the route-map used for redistributing into OSPF still sets the tag to the correct value. However, the table map no longer matches the correct tag. Rather, it matches the default tag. As a result, member A (could be B) would install the route through OSPF pointing to B. It would then redistribute it back into BGP with the med set to 1. The rest of the fabric (including member B) would install the BGP route pointing to member A since its med is better than the original route's med.

12.3(1e) and later

CSCvs76848

A switch SSD fails in less than two years and needs replacement. The /mnt/pss/ssd_log_amp.log file shows daily P/E cycles increasing by 10 or more each day, and fault "F3525: High SSD usage" is observed. Check the switch activity and contact Cisco Technical Support if the "High SSD usage" fault is raised on the switch.

12.3(1e) and later

CSCvt82388

A switch SSD fails in less than two years and needs replacement. The /mnt/pss/ssd_log_amp.log file shows daily P/E cycles increasing by 10 or more each day, and fault "F3525: High SSD usage" is observed. ARP/ICMPv6 adjacency updates can also contribute to many SSD writes.

12.3(1e) and later

CSCvu01639

There are faults for failed contract rules and prefixes on switches prior to the -EX switches. Furthermore, traffic that is destined to an L3Out gets dropped because the compute leaf switches do not have the external prefix programmed in ns shim GST-TCAM. You might also see that leaf switches prior to the -EX switches do not have all contracts programmed correctly in the hardware.

12.3(1e) and later

CSCvu07844

When a Cisco N9K-C93180LC-EX, N9K-93180YC-EX, or N9K-C93108TC-EX leaf switch receives control, data, or BUM traffic from the front panel ports with the storm policer configured for BUM traffic, the storm policer will not get enforced. As such, the switch will let all such traffic through the system.

12.3(1e) and later

CSCvc33025

When a Layer 2 domain is stretched through the ACI fabric across multiple sites using stretched fabric with N9K-93108TC-EX, N9K-93180YC-EX, or N9K-C93180LC-EX switches as the transit TORs and a tenant’s configuration is deployed on them, this setup can lead to a longer convergence time for multi-destination packets in the event of network triggers. You should deploy N9K-93108TC-EX, N9K-93180YC-EX, or N9K-C93180LC-EX switches as pure transit if such a configuration cannot be avoided (spanning tree domain extended across sites).

12.3(1e)

CSCvc35197

Upon a stateless reload of the TOR, the VSAN on the NP port does not come up. This is because under heavy load, the FCF MAC programming takes longer than expected. In this case, FCF_MAC against the VSAN is programmed in the EPMC even though the VSAN is shown as “down” in the "show npv status" command.

12.3(1e)

CSCvc46611

If Layer 3 multicast is deployed in the fabric with more than two border leaf switches and a multicast traffic source is connected to fabric behind an L3Out, with fast convergence enabled for Layer 3 multicast, periodically there could be a multicast packet duplication for a few seconds in the fabric for a fraction of the groups.

12.3(1e)

CSCvc50422

When the transit ToR is an N9K-C93120TX, N9K-93128TX, N9K-C9332PQ, N9K-C9372PX, N9K-C9372PX-E, N9K-C9372TX, N9K-C9372TX-E, N9K-9396PX, N9K-9396TX, N9K-M6PQ GEM, or N9K-M6PQ-E GEM switch in a stretched fabric deployment, the .1Q tag of packets in unidirectional traffic—meaning that the destination endpoint is not known as an ingress ToR—is not preserved when it is switched within an 802.1Q tunneling bridge domain.

12.3(1e)

CSCvd34047

Many MTS messages are seen in the MTS buffer for SAP 213.

12.3(1e)

CSCvd51695

With more than 50,000 policy cam entries and depending on your configuration, upgrading from the 2.0(2) release to the 2.2(2) release can take several minutes longer to complete after the bootstrap is complete.

12.3(1e)

CSCve82313

Common Pervasive Gateway might not source Address Resolution Protocol (ARP) requests with Pseudo MAC (PMAC).

12.3(1e)

CSCvm96490

After a policy upgrade, fault "F1583 - BIOS version mismatch detected." is present for N9K-C93108TC-EX and N9K-C93180YC-EX switches.

12.3(1e)

CSCvf12659

Cisco ACI leaf switches will send DHCP ACK back to the DHCP client as a "BROADCAST" when the bootp flag is set to "UNICAST."

12.3(1i)

CSCvf67718

An EX linecard or E fabric module crashes and resets when it encounters the PCIe uncorrectable error. You can see that the card failed, powered off, and then got removed and reinserted by navigating to the following location in the Cisco APIC GUI and viewing the events:

Fabric > Inventory > Pod x > Spine > History > Events

12.3(1i)

CSCvf73694

When using OpenStack to deploy a VM and the setup contains a FEX and N9K-C93180YC-EX switch, two NICs of one node go down. In addition, the Cisco OpFlex loses connection to the other nodes in the same FEX. As a result, the host loses infra VLAN connectivity to the fabric.

12.3(1i)

CSCvf80829

Traffic is not evenly load balanced onto all of the member links in a port channel.

12.3(1i)

CSCvf81062

A linecard or fabric module cannot be initialized successfully due to the image failing to download from the supervisor engine. The linecard or fabric module remains in the "inserted" status even after being reset.

12.3(1i)

CSCvg04269

IP addresses do not get learned with GARP traffic when IP learning is disabled on the bridge domain.

12.3(1i)

CSCve40174

The IP address is missing in COOP after performing some fast IP address moves across a pod or site.

12.3(1l)

CSCvg05802

A leaf switch crashes after techsupport collection is triggered for that leaf switch.

12.3(1l)

CSCvh17376

This is an enhancement request to strengthen the implementation of vPC to avoid a split brain scenario in the case of the control plane becoming irresponsive while the data plane is still forwarding traffic.

12.3(1l)

CSCvc51529

Endpoints connected to a FEX vPC might move as traffic is load-balanced across vPC members.

For example, if leaf1 and leaf2 are a vPC pair and have FEXes connected that have the vPC member ports, and if an endpoint that is learned on this vPC is communicating with an endpoint that is connected to some other leaf switch, that remote leaf will see a remote-to-remote endpoint move. This is because the source TEP being set by leaf 1 and leaf 2 is the physical leaf switch TEP rather than the vPC TEP that both own.

Excessive endpoint moves could lead to other symptoms, such as learning getting disabled on a bridge domain.

12.3(1o)

CSCve60216

A Cisco ACI border leaf switch might not be able to ping the next hop router's IP address. Additionally, it will not be able to route traffic out of the fabric through the L3Out.

When running the "show ip arp" command for the VRF instance, you might see something similar to the following entry (with negative age) for the next hop:

Address         Age       MAC Address     Interface

10.10.10.10  -00:00:00 0123.4567.8910   vlan10

12.3(1o)

CSCve80460

DTEP tunnels flap every 20 minutes.

12.3(1o)

CSCve88634

If a switch exhausts the terabytes written (TBW) threshold for an SSD, the drive might go into a read-only mode, which triggers the switch to crash and suffer subsequent boot failures, which requires the switch to be replaced.  On console, the following log might be seen:

/dev/hd-pss: ********** WARNING: Filesystem still has errors **********

e2fsck 1.42.1 (17-Feb-2012)

/dev/hd-bootflash: recovering journal

/sbin/e2fsck: unable to set superblock flags on /dev/hd-bootflash

12.3(1o)

CSCvf27593

The DHCP offer (relay packet) from the DHCP server gets dropped on the ToR that is connected to the server.

12.3(1o)

CSCvf52033

A kernel crash is observed when an iping request is done with the -R option.

12.3(1o)

CSCvf59666

HAL crashes if the number of routes is beyond the scale limit and some routes are added and deleted quickly.

12.3(1o)

CSCvf65152

ipfib crashes if some routes are added and deleted quickly. This bug has a generic crash backtrace, which can happen due to multiple reasons. Check the FIB traces to determine the reason.

12.3(1o)

CSCvg16267

The dynamic tunnel that is needed for inter-pod traffic does not get setup when the stream that is sent is subjected to a policy-based redirect policy.

12.3(1o)

CSCvg18830

ipfib crashes if the number of routes is beyond the scale limit and some routes are added and deleted quickly.

12.3(1o)

CSCvg58924

ICMP traffic to between endpoints might get dropped, but other traffic, including TCP and UDP, are not impacted.

12.3(1o)

CSCvg65487

A ToR switch fails to join the fabric.

12.3(1o)

CSCvh51474

A leaf switch reloads while collecting tech support files, and there is a core file from the unicast Routing Information Base (RIB) process.

12.3(1o)

CSCvh53787

ipfib crashes if the number of routes is beyond the scale limit and some routes are added and deleted quickly.

12.3(1o)

CSCvh85309

Under certain situations, the log files for the forwarding traces are lost.

12.3(1o)

CSCvh89176

The loss of prefix list entries for a shared L3Out causes the leaf switch to stop advertising its subnets.

12.3(1o)

CSCvh91642

If VLAN scale limit is hit, the VLAN translation table will not be cleaned up even after removing overscale VLANs. This can introduce unexpected connectivity issues for those VLANs that do not have a translation entry.

12.3(1o)

CSCve75260

BGP and COOP are out of sync after endpoint flaps.

12.3(1p)

CSCve89025

A certain type of IP fragmented packet is always dropped by a Cisco N9K-C93180LC-EX, N9K-93180YC-EX, or N9K-C93108TC-EX leaf switch.

12.3(1p)

CSCvf65335

Fragmented packets with an IP fragment offset set to less than 0x14(20)=160 bytes are dropped on Cisco N9K-X9736C-EX, N9K-X97160YC-EX, and N9K-X9732C-EX leaf switches.

12.3(1p)

CSCvg00085

After a Cisco N9K-C93180LC-EX leaf switch reload, the QSFP-40G-SR4 is not working; the Oper State of the port of the leaf switch is down. The only way to bring it up is to physically remove, then reinsert this QSFP.

After the leaf switch reload, when QSFP-40G-SR4 does not work. The Oper State remains down even after performing the following actions:

Disabling then enabling the port of the Leaf in the APIC GUI

Changing the port configuration (link speed, ...)

Unplugging and re-plugging the optical cable

Disabling then enabling the port of the remote connected equipment

12.3(1p)

CSCvj76998

The ipfib service on a spine linecard experiences a HAP reset.

12.3(1p)

CSCuo37016

When configuring the output span on a FEX Hif interface, all the layer 3 switched packets going out of that FEX Hif interface are not spanned. Only layer 2 switched packets going out of that FEX Hif are spanned.

12.3(1e) and later

CSCuo50533

When output span is enabled on a port where the filter is VLAN, multicast traffic in the VLAN that goes out of that port is not spanned.

12.3(1e) and later

CSCup65586

The show interface command shows the tunnel's Rx/Tx counters as 0.

12.3(1e) and later

CSCup82908

The show vpc brief command displays the wire-encap VLAN Ids and the show interface .. trunk command displays the internal/hardware VLAN IDs. Both VLAN IDs are allocated and used differently, so there is no correlation between them.

12.3(1e) and later

CSCup92534

Continuous “threshold exceeded” messages are generated from the fabric.

12.3(1e) and later

CSCuq39829

Switch rescue user ("admin") can log into fabric switches even when TACACS is selected as the default login realm.

12.3(1e) and later

CSCuq46369

An extra 4 bytes is added to the untagged packet with Egress local and remote SPAN.

12.3(1e) and later

CSCuq77095

When the command show ip ospf vrf <vrf_name> is run from bash on the border leaf, the checksum field in the output always shows a zero value.

12.3(1e) and later

CSCuq83910

When an IP address moves from one MAC behind one ToR to another MAC behind another ToR, even though the VM sends a GARP packet, in ARP unicast mode, this GARP packet is not flooded. As a result, any other host with the original MAC to IP binding sending an L2 packet will send to the original ToR where the IP was in the beginning (based on MAC lookup), and the packet will be sent out on the old port (location). Without flooding the GARP packet in the network, all hosts will not update the MAC-to-IP binding.

12.3(1e) and later

CSCuq92447

When modifying the L2Unknown Unicast parameter on a Bridge Domain (BD), interfaces on externally connected devices may bounce. Additionally, the endpoint cache for the BD is flushed and all endpoints will have to be re-learned.

12.3(1e) and later

CSCuq93389

If an endpoint has multiple IPs, the endpoint will not be aged until all IPs go silent. If one of the IP addresses is reassigned to another server/host, the fabric detects it as an IP address move and forwarding will work as expected.

12.3(1e) and later

CSCur01336

The power supply will not be detected after performing a PSU online insertion and removal (OIR).

12.3(1e) and later

CSCur81822

The access-port operational status is always “trunk”.

12.3(1e) and later

CSCus18541

An MSTP topology change notification (TCN) on a flood domain (FD) VLAN may not flush endpoints learned as remote where the FD is not deployed.

12.3(1e) and later

CSCus29623

The transceiver type for some Cisco AOC (active optical) cables is displayed as ACU (active copper).

12.3(1e) and later

CSCus43167

Any TCAM that is full, or nearly full, will raise the usage threshold fault. Because the faults for all TCAMs on leaf switches are grouped together, the fault will appear even on those with low usage.

Workaround:  Review the leaf switch scale and reduce the TCAM usage. Contact TAC to isolate further which TCAM is full.

12.3(1e) and later

CSCus54135

The default route is not leaked by BGP when the scope is set to context. The scope should be set to Outside for default route leaking.

12.3(1e) and later

CSCus61748

If the TOR 1RU system is configured with the RED fan (the reverse airflow), the air will flow from front to back. The temperature sensor in the back will be defined as an inlet temperature sensor, and the temperature sensor in the front will be defined as an outlet temperature sensor.

If the TOR 1RU system is configured with the BLUE fan (normal airflow), the air will flow from back to front. The temperature sensor in the front will be defined as an inlet temperature sensor, and the temperature sensor in the back will be defined as outlet temperature sensor.

From the airflow perspective, the inlet sensor reading should always be less than the outlet sensor reading. However, in the TOR 1RU family, the front panel temperature sensor has some inaccurate readings due to the front panel utilization and configuration, which causes the inlet temperature sensor reading to be very close, equal, or even greater than the outlet temperature reading.

12.3(1e) and later

CSCut59020

If Backbone and NSSA areas are on the same leaf, and default route leak is enabled, Type-5 LSAs cannot be redistributed to the Backbone area.

12.3(1e) and later

CSCuu11347

Traffic from the orphan port to the vPC pair is not recorded against the tunnel stats.  Traffic from the vPC pair to the orphan port is recorded against the tunnel stats.

12.3(1e) and later

CSCuu11351

Traffic from the orphan port to the vPC pair is only updated on the destination node, so the traffic count shows as excess.

12.3(1e) and later

CSCuu66310

If a bridge domain "Multi Destination Flood" mode is configured as "Drop", the ISIS PDU from the tenant space will get dropped in the fabric.

12.3(1e) and later

CSCuv57302

Atomic counters on the border leaf do not increment for traffic from an endpoint group going to the Layer 3 out interface.

12.3(1e) and later

CSCuv57315

Atomic counters on the border leaf do not increment for traffic from the Layer 3 out interface to an internal remote endpoint group.

12.3(1e) and later

CSCuv57316

TEP counters from the border leaf to remote leaf nodes do not increment.

12.3(1e) and later

CSCuw09389

For direct server return operations, if the client is behind the Layer 3 out, the server-to-client response will not be forwarded through the fabric.

12.3(1e) and later

CSCux97329

With the common pervasive gateway, only the packet destination to the virtual MAC is being properly Layer 3 forwarded. The packet destination to the bridge domain custom MAC fails to be forwarded. This is causing issues with certain appliances that rely on the incoming packets’ source MAC to set the return packet destination MAC.

12.3(1e) and later

CSCuy00084

BCM does not have a stats option for yellow packets/bytes, and so BCM does not show in the switch or APIC GUI stats/observer.

12.3(1e) and later

CSCuy02543

Bidirectional Forwarding Detection (BFD) echo mode is not supported on IPv6 BFD sessions carrying link-local as the source and destination IP address. BFD echo mode also is not supported on IPv4 BFD sessions over multihop or VPC peer links.

12.3(1e) and later

CSCuy06749

Traffic is dropped between two isolated EPGs.

12.3(1e) and later

CSCuy22288

The iping command’s replies get dropped by the QOS ingress policer.

12.3(1e) and later

CSCuy25780

An overlapping or duplicate prefix/subnet could cause the valid prefixes not to be installed because of batching behavior on a switch. This can happen during an upgrade to the 1.2(2) release.

12.3(1e) and later

CSCuy47634

EPG statistics only count total bytes and packets. The breakdown of statistics into multicast/unicast/broadcast is not available on new hardware.

12.3(1e) and later

CSCuy56975

You must configure different router MACs for SVI on each border leaf if L3out is deployed over port-channels/ports with STP and OSPF/OSPFv3/eBGP protocols are used. There is no need to configure different router MACs if you use VPC.

12.3(1e) and later

CSCuy61018

The default minimum bandwidth is used if the BW parameter is set to "0", and so traffic will still flow.

12.3(1e) and later

CSCuy96912

The debounce timer is not supported on 25G links.

12.3(1e) and later

CSCuz12913

An ACI leaf switch sends ARP to a device (such as a router or host) that belongs to directly connected subnets for an L3Out. After ARP is resolved, devices in directly connected subnets on two different L3Outs can talk each other without any contracts.

12.3(1e) and later

CSCuz13529

With the N9K-C93180YC-EX switch, drop packets, such as MTU or storm control drops, are not accounted for in the input rate calculation.

12.3(1e) and later

CSCuz13614

For traffic coming out of an L3out to an internal EPG, stats for the actrlRule will not increment.

12.3(1e) and later

CSCuz13810

When subnet check is enabled, a ToR does not learn IP addresses locally that are outside of the bridge domain subnets. However, the packet itself is not dropped and will be forwarded to the fabric. This will result in such IP addresses getting learned as remote endpoints on other ToRs.

12.3(1e) and later

CSCuz47058

SAN boot over a virtual Port Channel or traditional Port Channel does not work.

12.3(1e) and later

CSCuz65221

A policy-based redirect (PBR) policy to redirect IP traffic also redirects IPv6 neighbor solicitation and neighbor advertisement packets.

12.3(1e) and later

CSCva98767

The front port of the QSA and GLC-T 1G module has a 10 to 15-second delay as it comes up from the insertion process.

12.3(1e) and later

CSCvb36823

If you have only one spine switch that is part of the infra WAN and you reload that switch, there can be drops in traffic. You should deploy the infra WAN on more than one spine switch to avoid this issue.

12.3(1e) and later

CSCvb39965

Slow drain is not supported on FEX Host Interface (HIF) ports.

12.3(1e) and later

CSCvb49451

In the case of endpoints in two different TOR pairs across a spine switch that are trying to communicate, an endpoint does not get relearned after being deleted on the local TOR pair. However, the endpoint still has its entries on the remote TOR pair.

12.3(1e) and later

CSCvd11146

Bridge domain subnet routes advertised out of the Cisco ACI fabric through an OSPF L3Out can be relearned in another node belonging to another OSPF L3Out on a different area.

12.3(1e) and later

CSCvd63567

After upgrading a switch, Layer 2 multicast traffic flowing across PODs gets affected for some of the bridge domain Global IP Outsides.

12.3(1e) and later

CSCvd80766

When IGMP snooping is disabled on a bridge domain across the fabric, if a N9K-X9636 series switch is a transit leaf switch in the traffic path and the bridge domain is not deployed on the transit leaf switch, IGMP control packets will not be flooded and instead will be consumed by the switch.

12.3(1e) and later