The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Description: Add a custom MAC address to the bridgedomain
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# interface bridge-domain <WORD> (config-tenant-interface)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Manually set interface MAC address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface vlan <1-4094> (config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure mac Address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Add a rule to match DSCP or DOT1P, queue the traffic and optionally mutate it
Syntax:
dscp |
Match entry for DSCP |
dot1p |
Match entry for DOT1P |
WORD |
From of DSCP or DOT1P range |
WORD |
To of DSCP or DOT1P range |
WORD |
(Optional) Set the QOS class for the traffic |
WORD |
(Optional) DSCP rewrite |
Command Mode: policy-map type qos : QOS policy type
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# policy-map type qos <WORD> (config-tenant-pmap-qos)# match dscp|dot1p <WORD> <WORD> [set-class <WORD>] [set-dscp <WORD>]
Description: Match the ARP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match arp
Description: Match subnets of a bridge-domain
Syntax:
arg |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match bridge-domain <>
Description: Configure community features
Syntax:
WORD |
Name of community |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match community <WORD>
Description: Match the ICMP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match icmp
Description: Match the IP traffic
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match ip
Description: Add a subnet that identify hosts being part of the epg
Syntax:
A.B.C.D/LEN |
IP prefix and network mask length |
shared |
(Optional) Add the shared scope to the existing scope for the subnet |
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>] (config-tenant-l3ext-epg)# match ip <A.B.C.D/LEN> [shared]
Description: Add a subnet that identify hosts being part of the epg
Syntax:
X:X:X:X::X/<0-128> |
IPv6 prefix and network mask length |
Command Mode: external-l3 epg : External L3 EPG configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>] (config-tenant-l3ext-epg)# match ipv6 X:X:X:X::X/<0-128>
Description: Match entries of a prefix-list
Syntax:
WORD |
Name of prefix-list (Max Size 63) |
Command Mode: route-map : Create route-map or enter route-map command mode
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>] (config-leaf-vrf)# route-map <WORD> (config-leaf-vrf-route-map)# match prefix-list <WORD>
Description: Specify a raw vzEntry
Syntax:
WORD |
Entry Name (Max Size 64) |
tcpRules |
(Optional) TCP Flags as comma separated values like val1,val2,..valN |
arpOpc |
(Optional) ARP Opcodes |
applyToFrag |
(Optional) Apply to Fragment |
<0-65535> |
(Optional) L4 Destination Port. Number range from=0 to=65535 |
<0-255> |
(Optional) IP Protocol. Number range from=0 to=255 |
icmpv4T |
(Optional) ICMP Type |
stateful |
(Optional) Stateful flag |
icmpv6T |
(Optional) ICMPv6 Type |
<0-65535> |
(Optional) L4 Source Port. Number range from=0 to=65535 |
etherT |
(Optional) Ethernet Type |
<0-65535> |
(Optional) L4 Source Port. Number range from=0 to=65535 |
<0-65535> |
(Optional) L4 Destination Port. Number range from=0 to=65535 |
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match raw <WORD> [tcpRules <tcpRules>] [arpOpc <arpOpc>] [applyToFrag <applyToFrag>] [dToPort <NUMBER>] [prot <NUMBER>] [icmpv4T <icmpv4T>] [stateful <stateful>] [icmpv6T <icmpv6T>] [sToPort <NUMBER>] [etherT <etherT>] [sFromPort <NUMBER>] [dFromPort <NUMBER>]
Description: Match TCP traffic
Syntax:
<from>-[<to>] contained in <0-65535> |
(Optional) TCP Source port Range |
<from>-[<to>] contained in <0-65535> |
(Optional) TCP Destination port Range |
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match tcp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description: Match UDP traffic
Syntax:
<from>-[<to>] contained in <0-65535> |
(Optional) UDP Source port Range |
<from>-[<to>] contained in <0-65535> |
(Optional) UDP Destination port Range |
Command Mode: access-list : Create access-list
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# access-list <WORD> (config-tenant-acl)# match udp [src <from>-[<to>] contained in <0-65535>] [dest <from>-[<to>] contained in <0-65535>]
Description: Feature to limit the number of non-self-originated LSAs
Syntax:
<1-4294967295> |
Set maximum number of non self-generated LSAs. Number range from=1 to=4294967295 |
<1-100> |
Threshold value (%) at which to generate a warning message. Number range from=1 to=100 |
reject |
Reject LSAs beyond the limit |
restart |
Restart the neighbor |
log |
log a warning |
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template ospf vrf-policy <WORD> tenant <WORD> (config-vrf-policy)# max-lsa <NUMBER> <NUMBER> reject|restart|log
Description: Set The maximum validity period for a webtoken
Syntax:
<4-24> |
Set The maximum validity period for a webtoken. Number range from=4 to=24 |
Command Mode: crypto webtoken : The cryptographic data used for generating and verifying web tokens.
Command Path:
# configure [['terminal', 't']] (config)# crypto webtoken (config-webtoken)# max-validity-period <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
nodes |
Maximum number of tasks that can be processed concurrently. |
<0-65535> |
Enter maximum number of concurrent nodes. 0 for unlimited. Number range from=0 to=65535 |
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# absolute window <WORD> (config-scheduler-absolute)# max concurrent nodes <NUMBER>
Description: Set the window maximum concurrent node limit
Syntax:
nodes |
Maximum number of tasks that can be processed concurrently. |
<0-65535> |
Enter maximum number of concurrent nodes. 0 for unlimited. Number range from=0 to=65535 |
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# recurring window <WORD> (config-scheduler-recurring)# max concurrent nodes <NUMBER>
Description: Set the window maximum running time
Syntax:
time |
Maximum running time |
TIME |
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimited |
Command Mode: absolute : Absolute window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# absolute window <WORD> (config-scheduler-absolute)# max running time <TIME>
Description: Set the window maximum running time
Syntax:
time |
Maximum running time in milliseconds |
TIME |
Enter the maximum running time in dd:hh:mm:ss. 0 for unlimited |
Command Mode: recurring : Recurring window configuration mode
Command Path:
# configure [['terminal', 't']] (config)# scheduler fabric|controller schedule <WORD> (config-scheduler)# recurring window <WORD> (config-scheduler-recurring)# max running time <TIME>
Description: Set the maximum ECMP for the OSPF protocol
Syntax:
<1-64> |
Maximum paths. Number range from=1 to=64 |
Command Mode: template ospf vrf-policy : Configure Router OSPF Timer Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template ospf vrf-policy <WORD> tenant <WORD> (config-vrf-policy)# maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
<1-32> |
Maximum Path Limit. Number range from=1 to=32 |
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD> (config-template-eigrp-vrf-pol)# maximum-paths <NUMBER>
Description: Set EIGRP Maximum Path Limit
Syntax:
<1-32> |
Maximum Path Limit. Number range from=1 to=32 |
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router eigrp default (config-eigrp)# vrf member tenant <WORD> vrf <WORD> (config-eigrp-vrf)# address-family ipv4|ipv6 unicast (config-address-family)# maximum-paths <NUMBER>
Description: Maximum number of prefixes from this neighbor
Syntax:
<1-300000> |
Max. prefix limit. Number range from=1 to=300000 |
<action> |
(Optional) Action to be performed when the maximum prefix limit is reached |
<1-100> |
(Optional) The threshold % of the maximum number of prefixes before a warning is issued. Number range from=1 to=100 |
<1-65535> |
(Optional) The period of time in minutes before restarting the peer when the prefix limit is reached. Number range from=1 to=65535 |
Command Mode: address-family : Configure an address-family for peer
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router bgp <fabric-ASN> (config-bgp)# vrf member tenant <WORD> vrf <WORD> (config-leaf-bgp-vrf)# neighbor A.B.C.D|A.B.C.D/LEN|A:B::C:D|A:B::C:D/LEN [l3out <WORD>] (config-leaf-bgp-vrf-neighbor)# address-family ipv4|ipv6 unicast (config-leaf-bgp-vrf-neighbor-af)# maximum-prefix <NUMBER> [action <action>] [threshold <NUMBER>] [restart-time <NUMBER>]
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: template policy-group : Configure Policy Group Parameters
Command Path:
# configure [['terminal', 't']] (config)# template policy-group <WORD> (config-pol-grp-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: template port-channel : Configure Port-Channel Parameters
Command Path:
# configure [['terminal', 't']] (config)# template port-channel <WORD> (config-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface port-channel : Port Channel interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface port-channel <WORD> [fex <fex>] (config-leaf-if)# mcp enable
Description: Configure MCP interface parameters
Syntax:
enable |
Configure MCP parameters |
Command Mode: interface : Provide VPC Name
Command Path:
# configure [['terminal', 't']] (config)# vpc context leaf <101-4000> <101-4000> [fex <fex>] (config-vpc)# interface vpc <WORD> [fex <fex>] (config-vpc-if)# mcp enable
Description: Configure MCP Loop Protection Action
Syntax:
port-disable |
Disable the port when MCP detects loop |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp action port-disable
Description: Enable/Disable MCP Protocol
Syntax:
key |
Configure MCP key |
WORD |
MCP key |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp enable key <WORD>
Description: Configure MCP Loop Detection Factor
Syntax:
<1-255> |
MCP Loop Detection Multipication Factor. Number range from=1 to=255 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp factor <NUMBER>
Description: Configure MCP Loop Detection Init Delay Time
Syntax:
<0-1800> |
MCP Loop Detection Init Delay Time. Number range from=0 to=1800 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp init-delay <NUMBER>
Description: Configure MCP Advertisement Transmit Frequency
Syntax:
<2-300> |
MCP Advertisement Tx Frequency. Number range from=2 to=300 |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# mcp transmit-frequency <NUMBER>
Description: Configure Cluster Interface Member
Syntax:
device |
Cluster Device |
WORD |
Cluster Device name (Max Size 64) |
device-interface |
Cluster Device Interface |
WORD |
Cluster Device Interface (Max Size 256) |
Command Mode: cluster-interface : Configure L4-L7 Cluster Interface
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [service <service>] [function <function>] (config-cluster)# cluster-interface <WORD> [vlan <NUMBER>] (config-cluster-interface)# member device <WORD> device-interface <WORD>
Description: Configure the urgency of the message
Syntax:
info |
Info |
notice |
Notice |
emergency |
Emergency |
alert |
Alert |
critical |
Critical |
error |
Error |
debug |
Debug |
warning |
Warning |
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']] (config)# callhome common (config-callhome)# destination-profile (config-callhome-destnprof)# destination <WORD> (config-callhome-destnprof-destn)# message-level info|notice|emergency|alert|critical|error|debug|warning
Description: configure the size of the message
Syntax:
<size> |
The size of the messages. Number range from=0 to=5000000 |
Command Mode: destination : Configure destination Parameters
Command Path:
# configure [['terminal', 't']] (config)# callhome common (config-callhome)# destination-profile (config-callhome-destnprof)# destination <WORD> (config-callhome-destnprof-destn)# message-size <NUMBER>
Description: Set EIGRP Metric Style
Syntax:
version |
Metric Style |
64bit |
wide metric |
Command Mode: template eigrp vrf-policy : Configure EIGRP VRF policy templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template eigrp vrf-policy <WORD> tenant <WORD> (config-template-eigrp-vrf-pol)# metric version 64bit
Description: Set EIGRP Metric Style
Syntax:
version |
Metric Style |
64bit |
wide metric |
Command Mode: address-family : EIGRP Policy Address Family
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# router eigrp default (config-eigrp)# vrf member tenant <WORD> vrf <WORD> (config-eigrp-vrf)# address-family ipv4|ipv6 unicast (config-address-family)# metric version 64bit
Description: Select remote path management EPG
Syntax:
in-band |
In-Band EPG |
out-of-band |
Out-of-Band EPG |
WORD |
Management EPG name |
Command Mode: remote : Remote path configuration mode
Command Path:
# configure [['terminal', 't']] (config)# remote path <WORD> (config-remote)# mgmt-epg in-band|out-of-band <WORD>
Description: Create a VMM Microsoft Domain
Syntax:
WORD |
VMM Microsoft Domain name |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# microsoft-domain <WORD>
Description: Associate EPG to a Microsoft Domain
Syntax:
member |
Bind the EPG to a Microsoft domain |
WORD |
Microsoft Domain Name |
WORD |
(Optional) Enforce encap value. (For example vlan-10 or auto) |
WORD |
(Optional) Deployment mode |
WORD |
(Optional) Push mode |
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# epg <WORD> [type <WORD>] (config-tenant-app-epg)# microsoft-domain member <WORD> [encap <WORD>] [deploy <WORD>] [push <WORD>]
Description: Configure static ip pool
Syntax:
static-ip-pool |
Configure the static IP pool |
name |
enter the name of the static IP pool |
gateway |
Configure gateway address on interface |
gwAddress |
gwAddress |
Command Mode: epg : AEPg configuration mode
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# application <WORD> (config-tenant-app)# epg <WORD> [type <WORD>] (config-tenant-app-epg)# microsoft static-ip-pool <name> gateway <gwAddress>
Description: Configure BFD MIN-RX value in milliseconds
Syntax:
<interval> |
BFD interval. Number range from=50 to=999 |
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']] (config)# template bfd ip|ipv6 <WORD> (config-bfd)# min-rx <NUMBER>
Description: Configure required Minimum Rx Interval in milliseconds
Syntax:
<interval> |
Minimum Rx Interval. Number range from=50 to=999 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# min-rx <NUMBER>
Description: Configure BFD MIN-TX value in milliseconds
Syntax:
<interval> |
BFD interval. Number range from=50 to=999 |
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']] (config)# template bfd ip|ipv6 <WORD> (config-bfd)# min-tx <NUMBER>
Description: Configure required Minimum Tx Interval in milliseconds
Syntax:
<interval> |
Minimum Tx Interval. Number range from=50 to=999 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# min-tx <NUMBER>
Description: Set the minimum number of buffer of MTU size to be reserved
Syntax:
buffer |
Number of minim buffers to reserve |
<0-3> |
Number of minim buffers to reserve |
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']] (config)# qos parameters level1|level2|level3 (config-qos)# min buffer <0-3>
Description: Snapshot import mode atomic|best-effort
Syntax:
atomic |
Atomic mode |
best-effort |
Best Effort mode |
Command Mode: snapshot import : Configuration import setup mode
Command Path:
# configure [['terminal', 't']] (config)# snapshot import <WORD> (config-import)# mode atomic|best-effort
Description: Set the length of the encryption keys
Syntax:
<modulus> |
<modulus> |
Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate
Command Path:
# configure [['terminal', 't']] (config)# crypto keyring <WORD> (config-keyring)# modulus <modulus>
Description: Configure a monitor session
Syntax:
virtual |
virtual |
session |
session |
WORD |
session name (Max Size 64) |
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> (config-vmware)# configure-avs (config-vmware-avs)# monitor virtual session <WORD>
Description: Configue monitor session for access interfaces
Syntax:
session |
session |
session_name |
session name (Max Size 64) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name>
Description: Configue monitor session for fabric interfaces
Syntax:
session |
session |
session_name |
session name (Max Size 64) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor fabric session <session_name>
Description: Configue monitor session for tenant EPGs
Syntax:
tenant_name |
tenant name (Max Size 63) |
session |
session |
session_name |
session name (Max Size 64) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor tenant <tenant_name> session <session_name>
Description: Configure monitor session for virtual switches
Syntax:
session |
session |
WORD |
Session name (Max Size 64) |
Command Mode: configure : Configuration Mode
Command Path:
# configure [['terminal', 't']] (config)# monitor virtual session <WORD>
Description: Set OSPF Interface Policy Controls
Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template ospf interface-policy <WORD> tenant <WORD> (config-interface-policy)# mtu-ignore
Description: Set the MTU for this class of service
Syntax:
<1500-9216> |
MTU value |
Command Mode: qos parameters : Configure the global QOS policies
Command Path:
# configure [['terminal', 't']] (config)# qos parameters level1|level2|level3 (config-qos)# mtu <1500-9216>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
<576-9000> |
Interface MTU. Number range from=576 to=9000 |
Command Mode: interface vlan : Vlan interface
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface vlan <1-4094> (config-leaf-if)# mtu <NUMBER>
Description: Set the interface Maximum Transmission Unit (MTU)
Syntax:
<576-9000> |
Interface MTU. Number range from=576 to=9000 |
Command Mode: interface ethernet : Ethernet IEEE 802.3z
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# interface ethernet <ifRange> (config-leaf-if)# mtu <NUMBER>
Description: MTU size
Syntax:
mtu |
mtu value. Number range from=64 to=9216 |
Command Mode: destination tenant : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor access session <session_name> (config-monitor-access)# destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M> (config-monitor-access-dest)# mtu <mtu>
Description: MTU size
Syntax:
mtu |
mtu value. Number range from=64 to=9216 |
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor fabric session <session_name> (config-monitor-fabric)# destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M> (config-monitor-fabric-dest)# mtu <mtu>
Description: MTU size
Syntax:
arg |
mtu value. Number range from=64 to=9216 |
Command Mode: destination : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor tenant <tenant_name> session <session_name> (config-monitor-tenant)# destination tenant <tenant_name> application <application_name> epg <epg_name> destination-ip <A.B.C.D> source-ip-prefix <A.B.C.D/M> (config-monitor-tenant-dest)# mtu <>
Description: Configure MTU size
Syntax:
arg |
MTU value. Number range from=64 to=9216 |
Command Mode: destination destip : Configure monitor remote destination
Command Path:
# configure [['terminal', 't']] (config)# monitor virtual session <WORD> (config-monitor-virtual)# destination destip <A.B.C.D> (config-monitor-virtual-remote-dest)# mtu <>
Description: Change behavior for multi destination flood
Syntax:
WORD |
Unknown multicast MAC and Broadcast handling |
Command Mode: bridge-domain : Configuration for bridge-domain
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# bridge-domain <WORD> (config-tenant-bd)# multi-destination <WORD>
Description: Configure multi-site MAC address
Syntax:
E.E.E |
MAC address (Option 1) |
EE-EE-EE-EE-EE-EE |
MAC address (Option 2) |
EE:EE:EE:EE:EE:EE |
MAC address (Option 3) |
EEEE.EEEE.EEEE |
MAC address (Option 4) |
Command Mode: interface : Configuration for interface bridge-domain
Command Path:
# configure [['terminal', 't']] (config)# tenant <WORD> (config-tenant)# interface bridge-domain <WORD> (config-tenant-interface)# multi-site-mac-address E.E.E|EE-EE-EE-EE-EE-EE|EE:EE:EE:EE:EE:EE|EEEE.EEEE.EEEE
Description: Configure outgoing multicast IP address for VXLAN modes
Syntax:
IP |
Multicast IP |
Command Mode: configure-avs : Configure a VMware Domain as AVS (N1K) type
Command Path:
# configure [['terminal', 't']] (config)# vmware-domain <WORD> (config-vmware)# configure-avs (config-vmware-avs)# multicast-address <IP>
Description: Configure BFD MULTIPLIER value
Syntax:
<interval> |
BFD interval. Number range from=1 to=50 |
Command Mode: template bfd : BFD group of commands
Command Path:
# configure [['terminal', 't']] (config)# template bfd ip|ipv6 <WORD> (config-bfd)# multiplier <NUMBER>
Description: Configure detection multiplier
Syntax:
<interval> |
Detection multiplier. Number range from=1 to=50 |
Command Mode: template bfd : Configure BFD Interface Policy Templates
Command Path:
# configure [['terminal', 't']] (config)# leaf <101-4000> (config-leaf)# template bfd <WORD> tenant <WORD> (config-template-bfd-pol)# multiplier <NUMBER>