Open Caveats–Cisco IOS XE 17.15.5
There are no open caveats for this release.
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This chapter describes open and resolved severity 1 and 2 caveats and select severity 3 caveats:
The “Open Caveats” sections list open caveats that apply to the current release and may apply to previous releases. A caveat that is open for a prior release and is still unresolved applies to all future releases until it is resolved.
The “Resolved Caveats” sections list caveats resolved in a specific release, but open in previous releases.
The bug IDs are sorted alphanumerically.
![]() Note |
The Caveats section includes the bug ID and a short description of the bug. For details on the symptoms, conditions, and workaround for a specific caveat you must use the Bug Search Tool. |
There are no open caveats for this release.
|
Identifier |
Headline |
|---|---|
|
L2VPN pseudowire configuration is causing the GNMI state to go down. |
|
|
After upgrading to 17.12.4 or 17.12.5, no Rx values can be received on interface Te 0/0/26. |
|
Identifier |
Headline |
|---|---|
|
Disable unsupported BER rate at path layer - CISCOCE-345 |
|
|
ASR-920 - CFM MIP auto-creation issue: MIP is not displayed in link-traces. |
|
Identifier |
Headline |
|---|---|
|
REP loop formed with multicast MAC when advertised through VRRP protocol. |
|
|
ASR9xx shelf LED glowing without any alarm in the system - CISCOCE-316. |
|
|
ASR 902 router goes down with nested peer-policy templates. |
|
|
ASR-920-12SZ-IM: PSU/FAN showing as N/A after silent reload (last reboot reason is cpu hard reset). |
|
|
QoS buffer carving for control plane requires improvement. |
|
|
B3 SD and SF alarms raised concurrently. |
|
|
Reboot after running the show mac-address table, show bridge-domain, and other show commands. |
|
|
Smart licensing is not remaining registered status while the upgrading OS. |
|
|
Incorrect clock selection interface is displaying for the show network-clock sync CLI command. |
There are no open caveats in this release.
|
Identifier |
Headline |
|---|---|
|
Post reload HSRP is stuck in Init state and shows interface down |
|
|
XCVR incompatible alarm missing without Sonet controller configurations. |
|
|
Observed nnframed T1 as none and not shown in running-config under T3 controller. |
|
|
XCVR incompatible alarm not asserted in Bay0 sonet controller cards |
|
Identifier |
Headline |
|---|---|
|
Silent reload of 3GMS IM due to PCI transaction failure. |
|
|
LDP session flap causes memory leak for EMPLS3LD which leads to RSP crash. |
|
Identifier |
Headline |
|---|---|
|
Protocol or interface configuration from start or run file is missing after reload issue. |
|
|
17.9.2a-Both active and standby RSP's OAM or CFM configurations automatically changed after a reload. |
|
Identifier |
Headline |
|---|---|
|
Message to be displayed for M13 framing when configured with clear-channel |
|
|
Speed LED status is not correct when sonet/sdh mode is configured |
|
|
T1: Sev changes back from major to minor after IM OIR. |
|
|
Serial cease traffic when configuring module other port |
|
|
3GMS Serial interface protocol down with specific Modem |
|
|
Update 2^20-O151 QRSS bert help string with QRSS Keyword |
|
|
DCR clocking fails to get acquired on the with sts1-E mode |
|
|
Need to support dtr not-used CLI in RS232 transparent mode |
|
|
Channelized DS3: RAI is propagating to all DS1's when DS3 RAI is asserted |
|
Identifier |
Headline |
|---|---|
|
Enabling T1/E1 TPoP causes latency for control plane packets |
|
|
L-bit propogation not enabled for LOF alarm after framing change with framed SAToP |
|
|
BFD stuck in INIT state for interface Te0/0/0 & Te0/4/3 |
|
|
Increased CPU after upgrading router to 17.6.3 from 16.9.4 when 1000 SLM/DMM sessions are configured |
|
|
Confd process not in Started State in 5 mins after netconf-yang config is done |
|
|
After reconfiguring second synce source the QL-failed for that source interface and ranking also 254 |
Cisco Bug Search Tool (BST), the online successor to Bug Toolkit, is designed to improve effectiveness in network risk management and device troubleshooting. You can search for bugs based on product, release, and keyword, and aggregates key data such as bug details, product, and version. For more details on the tool, see the help page located at http://www.cisco.com/web/applicat/cbsshelp/help.html