Release Notes for Cisco ASR 9000 Series Routers, IOS XR Release
IOS XR 64-bit on Cisco ASR 9000 Series is the next generation operating system running in a virtualized environment with an underlying 64-bit Linux kernel. Cisco IOS XR operating system delivers greater agility, automation, and simplicity while reducing the cost of operating the networks.
References
For more information about Cisco ASR 9000 Series, see:
What's New in Cisco IOS XR Release 7.9.1
For more details on the Cisco IOS XR release model and associated support, see Guidelines for Cisco IOS XR Software.
Software Features Introduced and Enhanced
To learn about features introduced in other Cisco IOS XR releases, select the release from the Documentation Landing Page.
| Feature | Description |
|---|---|
|
Broadband Network Gateway |
|
|
We now support Line card based Internet over Ethernet (IPoE) subscriber sessions on the following : Also on the following Cisco ASR 9000 5th Generation High Density Ethernet line cards: |
|
|
You can now configure subscriber redundancy group (SRG) for the IPoE subscribers over bundle and PWHE access interfaces on the following: Also on the following Cisco ASR 9000 5th Generation High Density Ethernet line cards: SRG offers the advantage of enabling planned switch over or failover for all subscriber groups in case of a failure, proving especially advantageous for subscribers requiring high availability and geo-redundancy as part of their service level agreement (SLA). |
|
|
Interface and Hardware Component |
|
|
Exclude BNG interface statistics from show interface command |
The show interface command is modified to exclude the BNG interface statistics from the command output reduce the response time. Use the following keywords to exclude the BNG interface statistics.
|
|
Support for 3x100G Muxponder Mode on A99-10X400GE-X-SE/A99-10X400GE-X-TR Line Cards |
QDD-400G-ZRP-S optical module operating in A99-10X400GE-X-SE/A99-10X400GE-X-TR Line Cards now supports 3x100G Muxponder Mode. |
|
QDD-400G-ZRP-S optical module can now support the following oFEC traffic configurations:
This increases the interoperability of the QDD-400G-ZRP-S optical module across network components supporting these formats. |
|
|
This release introduces support for the Cisco 400G QSFP-DD High-Power (Bright) Optical Module, Ethernet Variant. The Cisco 400G QSFP-DD High-Power (Bright) Optical module is an enhanced version of the currently available QSFP-DD ZR+ Optical Module, leveraging the same operational modes but providing as a major enhancement the increase of the Tx Optical Power up to +1dBm. DP04QSDD-HE0 optical module is supported in the following hardware:
|
|
|
L2VPN and Ethernet Services |
|
|
Call Admission Control for L2VPN P2P Services over Circuit-Style SR-TE Policies |
This feature allows you to configure guaranteed bandwidth for Layer 2 P2P services steered over Circuit-Style SR-TE policies. This ensures that a Circuit-Style SR-TE policy has sufficient bandwidth to accommodate a Layer 2 P2P service, while also preventing a L2 P2P service from being steered over a Circuit-Style SR-TE policy when there is insufficient available bandwidth. |
|
Routing |
|
|
This feature allows you to specify the Flex-Algorithm number during route redistribution via a route policy. You can also select or filter the prefix-matching algorithm number during route redistribution so that only the Flex-Algorithms that you configured for specific addresses are redistributed. This feature introduces the set algorithm command. |
|
|
The nonself-generated link-state advertisements (LSAs) for a given Open Shortest Path First (OSPF) process is limited to 500000. This protection mechanism prevents routers from receiving many LSAs, preventing CPU failure and memory shortages, and is enabled by default from this release onwards. If you have over 500000 LSAs in your network, configure the max-lsa command with the expected LSA scale before upgrading to this release or later. This feature modifies the following commands:
|
|
|
Limiting the Maximum Redistributed Type-3 LSA Prefixes in OSPF |
By default, the maximum redistributed Type-3 LSA prefixes for a given OSPF process is now limited to 100000. This mechanism prevents OSPF from redistributing a large number of prefixes as Type-3 LSAs and therefore preventing high CPU utilization and memory shortages. Once the number of redistributed prefixes is reached or exceeds the threshold value, the system log message is generated, and no more prefixes are redistributed. |
|
Segment Routing |
|
|
This feature enhances the IS-IS Flexible Algorithm link admin group (affinity) constraint to include link colors on links in the reverse direction toward the calculating router. The ability to apply affinity constraints in the reverse direction provides additional control for IS-IS Flexible Algorithm path computation. |
|
|
Multicast: SR-PCE High Availability Support for Static Tree-SID |
This feature provides High Availability (HA) capability for static Tree-SID by using more than one Segment Routing Path Computation Elements (SR-PCE) in a multicast network. The feature helps in computing reliable paths for large and complex networks. |
|
SR-PCE: Stateful North-Bound API for Policies Containing IPv4 Unnumbered Interfaces |
The SR-PCE provides a north-bound HTTP-based API to allow communication between SR-PCE and external clients and applications. The Cisco Crosswork Optimization Engine is one of the applications that leverage the SR-PCE. This release adds support for the following:
For more information, refer to the Cisco Crosswork Optimization Engine User Guides. |
|
This feature allows traffic to a BGP service route to be steered over an SR-TE policy using the AS principles, and without imposing the service route’s prefix label. This feature enables use-cases such as centralized BGP EPE for 6PE in an SR-MPLS network. This feature introduces the following command:
|
|
|
SR-TE Explicit Segment Lists with Mix of IPv4 and IPv6 Segments |
Explicit segment list can be configured to include IPv6 segments, for example IPv6 adjacency SIDs or IPv6 EPE SIDs. This feature enables use-cases such as Centralized BGP EPE for 6PE in an SR-MPLS Network. |
|
This feature enables an SRv6 headend node to receive and install remote SIDs with Wide (32-bit) functions (Remote W-LIB). There is no new CLI to enable this capability at the ingress PE. |
|
|
Support for L3 EVPN/SRv6 and L3 EVPN/MPLS Interworking Gateway |
This feature adds support for L3 EVPN interworking between SRv6 and MPLS. L3 EVPN/SRv6 and L3 EVPN/MPLS Interworking Gateway enables you to extend L3 services between MPLS and SRv6 domains by providing service continuity on the control plane and data plane. This feature allows for SRv6 L3 EVPN domains to interwork with existing MPLS L3 EVPN domains. The feature also allows a way to migrate from MPLS L3 EVPN to SRv6 L3 EVPN. |
|
Support for L3 EVPN/SRv6 and L3VPN/MPLS Interworking Gateway |
This feature adds support for EVPN L3VPN interworking between SRv6 and MPLS. L3 EVPN/SRv6 and L3VPN/MPLS Interworking Gateway enables you to extend L3 services between MPLS and SRv6 domains by providing service continuity on the control plane and data plane. This feature allows for SRv6 L3 EVPN domains to interwork with existing MPLS L3VPN domains. The feature also allows a way to migrate from MPLS L3VPN to SRv6 L3 EVPN. |
|
This feature adds support for carrying L3VPN routes in L2VPN EVPN (AFI 25 SAFI 70) address-family RT5 instead of VPNv4 unicast and/or VPNv6 unicast address-family across SRv6 core (EVPN over SRv6 underlay). |
|
|
System Management |
|
|
It is now possible to use the 10GbE SFP+ and SFP28 ports to transmit 1GbE traffic on the routers or line cards. The number of ports on which you can enable 1GbE port mode has been increased from the previous releases. The details of the number of ports on which you can configure 1GbE port mode on the Cisco ASR 9000 Series routers, port expansion card, and line cards is as follows:
Use the hw-module location breakout and hw-module location slice config mode commands to enable 1GbE port mode configuration. |
|
|
You can now specify a Fully Qualified Domain Name (FQDN) as the hostname for NTP server configuration over nondefault VRFs. FQDNs are easy to remember compared to numeric IP addresses. Service migration from one host to another can cause a change in IP address leading to outages. Prior releases allowed FQDN handling in only default VRFs. |
|
|
Optional RPM for Software Innovation Access Out-of-Compliance |
Now, you can do a major upgrade even when your SIA is Out-of-Compliance (OOC) by using the license-util optional rpm. Earlier, when your SIA is OOC, you weren’t able to major upgrades. As a workaround, you were given a SMU, which disabled the SIA check. |
|
New Cisco-NTP-MIB Traps to Monitor NTP server and Improve Timing Accuracy |
CiscoNtpMIB allows you to monitor NTP on the server and client using SNMP MIB. Support for new traps is added in this release that will help monitor the NTP server and improvise on timing accuracy. These traps act as synchronization source. These traps also display the current status of the NTP server, the stratum of the local clock, maximum error in seconds and the delay in round-trip in seconds. Use MIB Navigator to know more about the newly added traps .The following is the list of newly added traps:
|
|
This feature now supports Onboard Failure logs (OBFL) when you use the show reboot history command. The logs are visible in the show output when you use this command. |
|
|
General Administration |
|
|
Auto-Save with Secure File-Transfer and Additional Configurable Parameters |
Apart from automatically backing up the running configuration after every commit, you can also do the following with Auto-Save:
The feature introduces these changes: CLI: Modified the configuration commit auto-save command Yang Data Model:
|
|
Now, you can securely transfer router files to an archive server. It’s made possible because the copy command now supports SFTP (Secure File Transfer Protocol) and SCP (Secure Copy Protocol using the underlying SSH protocol implementation. Secure transfer of files from the router maintains the integrity, confidentiality, and availability of network configurations. This feature modifies the copy command. |
|
|
Programmability |
|
|
Securely retrieve dynamic NACM with LDAP over TLS authentication |
You can now securely retrieve the NETCONF Access Control Model (NACM) policies or rules on-demand from a remote Lightweight Directory Access Protocol (LDAP) server to validate each NETCONF operation using Transport Layer Security (TLS) authentication. Before this release, the policies or rules were not encrypted and posed security vulnerabilities. With TLS authentication, the communication between the router and the LDAP server is encrypted for security. |
|
IP Addresses and Services |
|
|
Limit Address Resolution Protocol (ARP) Cache Entries per Interface |
In this feature, you can configure the maximum limit for the number of entries of dynamic mapping between IP addresses and media addresses by ARP per interface. Limiting the number of entries provides overflow protections in ARP cache and protects the routers from DOS attacks by preventing memory overuse by cache entries. This feature introduces the arp cache-limit command. |
|
System Security |
|
|
Securely retrieve NACM policies using LDAP over TLS connection |
You can now securely retrieve the NETCONF Access Control Model (NACM) policies or rules from a remote Lightweight Directory Access Protocol (LDAP) server using Transport Layer Security (TLS) authentication. With TLS authentication, the communication between the router and the LDAP server is encrypted for security. Before this release, the communication between the LDAP server and the router was not secured. |
YANG Data Models Introduced and Enhanced
This release introduces or enhances the following data models. For detailed information about the supported and unsupported sensor paths of all the data models, see the Github repository. To get a comprehensive list of the data models supported in a release, navigate to the Available-Content.md file for the release in the Github repository. The unsupported sensor paths are documented as deviations. For example, openconfig-acl.yang provides details about the supported sensor paths, whereas cisco-xr-openconfig-acl-deviations.yang provides the unsupported sensor paths for openconfig-acl.yang on Cisco IOS XR routers.
You can also view the data model definitions using the YANG Data Models Navigator tool. This GUI-based and easy-to-use tool helps you explore the nuances of the data model and view the dependencies between various containers in the model. You can view the list of models supported across Cisco IOS XR releases and platforms, locate a specific model, view the containers and their respective lists, leaves, and leaf lists presentedvisually in a tree structure.
To get started with using data models, see the Programmability Configuration Guide for ASR 9000 Series Routers.
| Feature | Description |
|---|---|
|
Programmability |
|
|
openconfig-isis.yang Version 1.0.0 |
The OpenConfig data model is revised from version 0.6.0 to 1.0.0 to simplify the authentication keychain nodes. With this feature, you can configure the authentication type to limit the establishment of adjacencies and the exchange of LSPs. You can also retrieve the operational state of the authentication nodes. |
|
openconfig-network-instance.yang |
With this release, the OpenConfig data model is enhanced to view the number of routes that are routed through a specific neighbour for each peer and Subsequent Address Family Identifiers (SAFI) installed counter. The counter reflects the current state of Border Gateway Protocol (BGP) and Routing Information Base (RIB), and can be monitored to check the presence of stale routes, missing routes, and the current installed state of the BGP routes in RIB. The model supports a single instance of BGP with default VRF, and address family (IPv4, IPv6). |
|
openconfig-network-instance.yang Version 0.2.3 |
In this release, the installed counter in the OpenConfig data model is enhanced to view the number of routes that are installed in Routing Information Base (RIB) from a specific neighbor per Address Family Identifiers (AFI) or Subsequent Address Family Identifiers (SAFI). The model supports a single instance of BGP with default VRF, and IPv4/IPv6 address family. Cross AFI where an IPv4 route learnt from an IPv6 neighbor, and vice versa, is not supported. You can stream Event-driven telemetry (EDT) and Model-driven telemetry (MDT) data. |
|
Cisco-IOS-XR-config-autosave-cfg |
This Cisco native yang data model enables you to automatically backup the running configuration files after every commit is made. |
|
Cisco-IOS-XR-um-config-commit-cfg |
This unified data model enables you to automatically backup the running configuration of the routerafter every commit is made. |
Hardware Introduced
Cisco IOS XR Release 7.9.1 introduces the following hardware support:
| Hardware Feature | Description |
|---|---|
|
Optics |
Note: Optics support varies across devices (routers, line cards, RPs, and so on). To know if an optics is compatible with a specific Cisco device, refer to the Transceiver Module Group (TMG) Compatibility Matrix. This release introduces the following optics:
|
Behavior Changes
-
Prior to Cisco IOS XR release 7.2.1, a segment of an explicit segment list can be configured as an IPv4 address (representing a Node or a Link) using the index indexaddress ipv4 address command.
Starting with Cisco IOS XR release 7.2.1, an IPv4-based segment (representing a Node or a Link) can also be configured with the new index index mpls adjacencyaddress command. The configuration is stored in NVRAM in the same CLI format used to create it. There is no conversion from the old CLI to the new CLI.
Starting with Cisco IOS XR release 7.9.1, the old CLI has been deprecated. Old configurations stored in NVRAM will be rejected at boot-up.
As a result, explicit segment lists with IPv4-based segments using the old CLI must be re-configured using the new CLI.
There are no CLI changes for segments configured as MPLS labels using the index index mpls label label command.
-
You must configure using the new CLI if you are using Cisco IOS XR Release 7.9.1 and above. In the updated CLI, the sid-algorithm is nested under constraints | segments .
segment-routing traffic-eng on-demand color 10 dynamic metric type igp ! ! constraints <----- New CLI segments sid-algorithm 131 ! ! ! -
If you are on a release before Cisco IOS XR Release 7.4.1, you can configure SR-ODN with Flexible Algorithm constraints using the segment-routing traffic-eng on-demand color color dynamic sid-algorithm algorithm-number command.
Starting with Cisco IOS XR release 7.4.1, you can also configure SR-ODN with Flexible Algorithm constraints using the new segment-routing traffic-eng on-demand color color constraints segments sid-algorithm algorithm-number command.
From Cisco IOS XR Release 7.9.1, the segment-routing traffic-eng on-demand color color dynamic sid-algorithm algorithm-number command is deprecated. Previous configurations stored in NVRAM will be rejected at boot-up.
Hence, for Cisco IOS XR Release 7.9.1, you must reconfigure all SR-ODN configurations with Flexible Algorithm constraints that use the on-demand dynamic sid-algorithm with the on-demand constraints command.
Caveats
There are no caveats in this release.
Supported Packages and System Requirements
Feature Set (Software Images)
Visit the Cisco Software Download page to download the Cisco IOS XR software.
Cisco IOS XR 64 bit
This table lists the feature set matrix (ISO and RPM files) and associated filenames available for the Cisco IOS XR 64 bit 7.9.1 Release supported on the Cisco ASR 9000 Series Aggregation Services Router.
|
Feature Set |
Filename |
Description |
|---|---|---|
|
Cisco IOS XR IP/MPLS Core Software [for RSP and RP systems] |
ASR9K-x64-iosxr-px-7.9.1.tar |
|
|
Cisco IOS XR IP/MPLS Core Software 3DES [for RSP and RP systems] |
ASR9K-x64-iosxr-px-k9-7.9.1.tar |
|
|
Cisco IOS XR IP Unicast Routing Core Bundle and Migration to IOS XR 64 bit tar image |
asr9k-mini-x64-migrate_to_eXR.tar-7.9.1 |
Contains the required core packages, including OS, Admin, Base,Forwarding, Modular Services Card, Routing, FPD, SNMP Agent, and Alarm Correlation. Contains mini.iso file for XR 64 bit 7.9.1 and additional software for migration to 64 bit. |
|
Composite Package |
||
|
Feature Set |
Filename |
Description |
|
Cisco IOS XR IP Unicast Routing Core Bundle |
asr9k-mini-x64-7.9.1.iso |
Contains the required core packages, including OS, Admin, Base,Forwarding, Modular Services Card, Routing, FPD, SNMP Agent, and Alarm Correlation. The mini iso file is used for upgrading to the new release. |
| Individually-Installable Optional Packages | ||
|
Feature Set |
Filename |
Description |
|
Cisco IOS XR 64 bit EIGRP package |
asr9k-eigrp-x64-1.0.0.0-r791.x86_64.rpm |
Includes EIGRP protocol support software |
|
Cisco IOS XR BNG Package |
asr9k-bng-x64-1.1.0.0-r791.x86_64.rpm |
Includes binaries to support BNG features. |
|
Cisco IOS XR 64 bit ISIS package |
asr9k-isis-x64-1.1.0.0-r791.x86_64.rpm |
Includes IS-IS Link state protocol support software |
|
Cisco IOS XR 64 bit OSPF package |
asr9k-ospf-x64-1.1.0.0-r791.x86_64.rpm |
Includes OSPF link state protocol support software |
|
Cisco IOS XR Manageability Package |
asr9k-mgbl-x64-3.0.0.0-r791.x86_64.rpm |
CORBA2 agent, XML3 Parser, and HTTP server packages. This RPM also contains some SNMP MIB infrastructure. Certain MIBs won't work if this RPM is not installed. IPSLA and environment MIBs are part of the mgbl rpm. |
|
Cisco IOS XR 64 bit MPLS-TE and RSVP package |
asr9k-mpls-te-rsvp-x64-1.2.0.0-r791.x86_64.rpm |
MPLS Traffic Engineering (MPLS-TE), Resource Reservation Protocol (RSVP). |
|
Cisco IOS XR 64 bit MPLS Package |
asr9k-mpls-x64-2.1.0.0-r791.x86_64.rpm |
Label Distribution Protocol (LDP), MPLS Forwarding, MPLS Operations, Administration, and Maintenance (OAM), Link Manager Protocol (LMP), Optical User Network Interface (OUNI) and Layer-3 VPN. |
|
Cisco IOS XR 64 bit Multicast Package |
asr9k-mcast-x64-2.0.0.0-r791.x86_64.rpm |
Multicast Routing Protocols (PIM, Multicast Source Discovery Protocol [MSDP], Internet Group Management Protocol [IGMP], Auto-RP), Tools (SAP, MTrace), and Infrastructure [(Multicast Routing Information Base [MRIB], Multicast-Unicast RIB [MURIB], Multicast forwarding [MFWD]), and Bidirectional Protocol Independent Multicast (BIDIR-PIM). |
|
Cisco IOS XR 64 bit Optics Package |
asr9k-optic-x64-1.0.0.0-r791.x86_64.rpm |
Firmware for the optics feature for Cisco ASR 9000 Series Aggregation Services Router Chassis. It enables Transport / OTN feature under interfaces. |
|
Cisco IOS XR 64 bit Lawful Intercept (LI) Package |
asr9k-li-x64-1.1.0.0-r791.x86_64.rpm |
Includes LI software images. |
|
Cisco IOS XR Security Package |
asr9k-k9sec-x64-3.1.0.0-r791.x86_64.rpm |
Support for Encryption, Decryption,, Secure Shell (SSH), Secure Socket Layer (SSL), and Public-key infrastructure (PKI). |
|
Cisco IOS XR Satellite Package -ASR9000v |
asr9k-9000v-nV-x64-1.0.0.0-r791.x86_64.rpm |
Includes RPM to support Cisco ASR9000v Series Router Software and to support Cisco ASR 9000v Series Router as a satellite for Cisco ASR 9000 Series Router |
|
Cisco IOS XR 64 bit Services Package |
asr9k-services-x64-1.0.0.0-r791.x86_64.rpm |
Includes RPM to support Cisco IOS XR 64-bit inline MAP-T function |
Memory
 Caution |
If you remove the media in which the software image or configuration is stored, the router may become unstable and fail. |
The available memory for Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release consist of the following:
-
32 GB memory on the A99-RP-F
-
16 GB memory on the RSP880, RSP880-LT, RP2, A99-RSP-TR and A99-RSP-SE
-
16 GB memory on the RP2 transport optimised (TR) variant and 32 GB memory on the RP2 service edge (SE) variant
-
24 GB memory on the RP3 transport optimised (TR) variant and 40 GB memory on the RP3 service edge (SE) variant
-
24 GB memory on the RP3-X transport optimised (TR) variant and 48 GB memory on the RP3-X service edge (SE) variant
-
24 GB memory on the RSP5 transport optimised (TR) variant and 40 GB memory on the RSP5 service edge (SE) variant
-
24 GB memory on the RSP5-X transport optimised (TR) variant and 48 GB memory on the RSP5-X service edge (SE) variant
-
2 GB compact flash on route switch processors (RSPs)
-
8 GB memory on the line cards (LCs) running Cisco IOS XR 64-bit image
Software Compatibility
Cisco IOS XR Software Release is compatible with the following Cisco ASR 9000 Series Aggregation Services Router systems.
-
Cisco ASR 9900 Series Chassis
-
Cisco ASR 9922 Chassis
-
Cisco ASR 9912 Chassis
-
Cisco ASR 9910 Chassis
-
Cisco ASR 9906 Chassis
-
Cisco ASR 9904 Chassis
-
Cisco ASR 9903 Chassis
-
Cisco ASR 9902 Chassis
-
Cisco ASR 9901 Chassis
-
-
Cisco ASR 9000 Series Chassis
-
Cisco ASR 9010 Chassis
-
Cisco ASR 9006 Chassis
-
For Cisco license support, please contact your Cisco Sales Representative or Customer Service at 800- 553-NETS (6387) or 408-526-4000. For questions on the program other than ordering, please send e-mail to: cwm-license@cisco.com.
Determining Installed Packages
To determine the version of Cisco IOS XR Software packages installed on your router, log in to the router and enter the show install active summary command:
Cisco IOS XR 64 bit
Router# show install active summary
Label : 7.9.1
Active Packages: 16
asr9k-xr-7.9.1 version=7.9.1 [Boot image]
asr9k-li-x64-1.0.0.0-r791
asr9k-mpls-x64-1.0.0.0-r791
asr9k-services-x64-1.0.0.0-r791
asr9k-mpls-te-rsvp-x64-1.0.0.0-r791
asr9k-mcast-x64-1.0.0.0-r791
asr9k-9000v-nV-x64-1.0.0.0-r791
asr9k-cnbng-x64-1.0.0.0-r791
asr9k-eigrp-x64-1.0.0.0-r791
asr9k-isis-x64-1.0.0.0-r791
asr9k-m2m-x64-1.0.0.0-r791
asr9k-optic-x64-1.0.0.0-r791
asr9k-bng-supp-x64-1.0.0.0-r791
asr9k-mgbl-x64-1.0.0.0-r791
asr9k-k9sec-x64-1.0.0.0-r791
asr9k-ospf-x64-1.0.0.0-r791Firmware Support on Cisco IOS XR 64-bit
To check the firmware code running on the Cisco ASR 9000 Series Router, run the show fpd package command in admin mode:
 Note |
The show command output lists supported and EOL hardware PIDs. To know the PIDs that are supported in this release, see the Supported Hardware section in this Release Notes. |
Supported Hardware
The following table lists the supported hardware components on the Cisco ASR 9000 Series Router and the minimum required software versions. For more information, see the Firmware Support section.
All hardware features are supported on Cisco IOS XR Software, subject to the memory requirements specified in the section.
For information on the end-of-sale and end-of-life dates for the Cisco ASR 9000 Series Router hardware, refer to the End-of-Life and End-of-Sale Notices page.
|
Cisco ASR 9000 Series Aggregation Services Router - Route Switch Processor Cards |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
A9K-RSP5-X-SE |
ASR 9000 Series Route Switch Processor 5 for Service Edge, Premium |
Release 7.6.2 |
|
A9K-RSP5-X-TR |
ASR 9000 Series Route Switch Processor 5 for Packet Transport, Premium |
Release 7.6.2 |
|
A9K-RSP5-SE |
ASR 9000 Route Switch Processor 5 for Service Edge |
Release 6.5.15 |
|
A9K-RSP5-TR |
ASR 9000 Route Switch Processor 5 for Packet Transport |
Release 6.5.15 |
|
A9K-RSP880-LT-SE |
Cisco ASR 9000 Series Aggregation Services Router RSP880-Lite, Service Edge Optimized |
Release 6.4.1 |
|
A9K-RSP880-LT-TR |
Cisco ASR 9000 Series Aggregation Services Router RSP880-Lite, Packet Transport Optimized |
Release 6.4.1 |
|
A99-RSP-SE |
Cisco ASR 9000 Series Aggregation Services Router RSP4-S, Service Edge Optimized for ASR 9910 from Release 6.0.1. |
Release 6.2.1 |
|
A99-RSP-TR |
Cisco ASR 9000 Series Aggregation Services Router RSP4-S, Packet Transport Optimized for ASR 9910 from Release 6.0.1. |
Release 6.2.1 |
|
A99-RSP-SE |
Cisco ASR 9000 Series Aggregation Services Router RSP4-S, Service Edge Optimized for ASR 9906 from Release 6.3.1. |
Release 6.3.1 |
|
A99-RSP-TR |
Cisco ASR 9000 Series Aggregation Services Router RSP4-S, Packet Transport Optimized for ASR 9906 supported from Release 6.3.1 |
Release 6.3.1 |
|
A9K-RSP880-SE |
ASR9K Route Switch Processor with 880G/slot and 32 GB for Service Edge |
Release 6.1.2 |
|
A9K-RSP880-TR |
ASR9K Route Switch Processor with 880G/slot and 16 GB for Packet Transport |
Release 6.1.2 |
|
Cisco ASR 9000 Series Aggregation Services Router - Route Processor Cards |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
A99-RP3-X-SE |
ASR 9900 Route Processor 3 for Service Edge, Premium |
Release 7.6.2 |
|
A99-RP3-X-TR |
ASR 9900 Route Processor 3 for Packet Transport, Premium |
Release 7.6.2 |
|
A99-RP3-SE |
ASR 9900 Route Processor 3 for Service Edge |
Release 6.5.15 |
|
A99-RP3-TR |
ASR 9900 Route Processor 3 for Packet Transport |
Release 6.5.15 |
|
A99-RP2-SE |
ASR Route Processor 32 GB for Service Edge |
Release 6.1.2 |
|
A99-RP2-TR |
ASR Route Processor 16 GB for Packet Transport |
Release 6.1.2 |
| Cisco ASR 9901 Router | ||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
| ASR-9901 |
Cisco ASR 9000 Series Aggregation Services Router 2-RU Fixed Port |
Release 6.4.1 |
|
ASR-9901-FAN |
Cisco ASR 9000 Series Aggregation Services Router 2-RU Fixed Port Fan Tray |
Release 6.4.1 |
|
A9K-1600W-AC |
Cisco ASR 9000 Series Aggregation Services Router 2-RU 1600W AC Power Module |
Release 6.4.1 |
|
A9K-1600W-DC |
Cisco ASR 9000 Series Aggregation Services Router 2-RU 1600W DC Power Module |
Release 6.4.1 |
|
Cisco ASR 9902 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9902 |
Cisco ASR 9902 2RU Chassis with fixed ports |
Release 7.4.1 |
|
A99-RP-F |
Cisco ASR 9900 Fixed Chassis Route Processor |
Release 7.1.3 |
|
ASR-9902-4P-KIT |
Cisco ASR 9902 4-Post Mounting Kit for 19-Inch and 23-Inch Rack |
Release 7.4.1 |
|
ASR-9902-4P-KIT-L |
ASR 9902 4-Post Mounting Kit for 19 & 23 inch Rack – Long |
Release 7.4.1 |
|
ASR-9902-2P-KIT |
Cisco ASR 9902 2-Post Mounting Kit for 19-Inch and 23-Inch Rack |
Release 7.4.1 |
|
ASR-9902-CAB-MGMT |
Cisco ASR 9902 Cable Management |
Release 7.4.1 |
|
ASR-9902-FILTER |
Cisco ASR 9902 Air Filter |
Release 7.4.1 |
|
ASR-9902-FAN |
Cisco ASR 9902 Fan Tray |
Release 7.4.1 |
|
Cisco ASR 9903 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9903 |
Cisco ASR 9903 Compact High-Performance Router with fixed ports and PEC (Port Expansion Card) slot. |
Release 7.1.3 |
|
A99-RP-F |
Cisco ASR 9900 Fixed Chassis Route Processor |
Release 7.1.3 |
|
ASR-9903-FAN |
Cisco ASR 9903 Router Fan Tray |
Release 7.1.3 |
|
ASR-9903-4P-KIT |
ASR 9903 4-Post Mounting Kit for 19-inch Rack |
Release 7.1.3 |
|
ASR-9903-CAB-MGMT |
ASR 9903 Cable Management Brackets |
Release 7.1.3 |
|
ASR-9903-FILTER |
ASR 9903 Air Filter |
Release 7.1.3 |
|
Cisco ASR 9904 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9904 |
Cisco ASR 9000 Series Aggregation Services Router 4-Slot 2 Line Card Slot Chassis, 6 RU |
Release 6.1.2 |
|
ASR-9904-AC |
Cisco ASR 9000 Series Aggregation Services Router 4-Slot 2 Line Card Slot AC Chassis w/ PEM V2 |
Release 6.1.2 |
|
ASR-9904-DC |
Cisco ASR 9000 Series Aggregation Services Router 4-Slot 2 Line Card Slot DC Chassis w/ PEM V2 |
Release 6.1.2 |
|
ASR-9904-FAN |
Cisco ASR 9000 Series Aggregation Services Router 4-Slot Fan Tray |
Release 6.1.2 |
|
ASR-9904-FILTER |
Cisco ASR 9000 Series Aggregation Services Router 4-Slot Filter |
Release 6.1.2 |
|
ASR-9904-BAFFLE |
Cisco ASR 9000 Series Aggregation Services Router 4-Slot Baffle |
Release 6.1.2 |
|
Cisco ASR 9912 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9912 |
Cisco ASR 9000 Series Aggregation Services Router 12-Slot 10 Line Card Slot Chassis |
Release 6.1.2 |
|
ASR-9912-AC |
Cisco ASR 9000 Series Aggregation Services Router 12-Slot 10 Line Card Slot AC Chassis w/ PEM V2 |
Release 6.1.2 |
|
ASR-9912-DC |
Cisco ASR 9000 Series Aggregation Services Router 12-Slot 10 Line Card Slot DC Chassis w/ PEM V2 |
Release 6.1.2 |
|
A99-SFC3 |
Cisco ASR 9900 Switch Fabric Card 3 |
Release 6.5.15 |
|
A99-SFC2 |
Cisco ASR 9000 Fabric Card |
Release 6.1.2 |
|
ASR-9912-FAN |
Cisco ASR 9000 Series Aggregation Services Router 12-Slot Fan Tray |
Release 6.1.2 |
|
Cisco ASR 9922 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9922 |
Cisco ASR 9922 20 Line Card Slot Chassis, 44 RU |
Release 6.1.2 |
|
ASR-9922-AC |
Cisco ASR 9000 Series Aggregation Services Router 22-Slot 20 Line Card Slot AC Chassis w/ PEM V2 |
Release 6.1.2 |
|
ASR-9922-DC |
Cisco ASR 9000 Series Aggregation Services Router 22-Slot 20 Line Card Slot DC Chassis w/ PEM V2 |
Release 6.1.2 |
|
A99-SFC3 |
Cisco ASR 9900 Switch Fabric Card 3 |
Release 6.5.15 |
|
A99-SFC2 |
Cisco ASR 9000 Fabric Card |
Release 6.1.2 |
|
ASR-9922-FAN-V3 |
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Fan Tray version 3 |
Release 6.5.15 |
|
ASR-9922-FLTR-CV2 |
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Air Filter with Media, Center |
Release 6.1.2 |
|
ASR-9922-FLTR-LR |
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Air Filter with Media, Left & Right |
Release 6.1.2 |
|
ASR-9922-RP-FILR |
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Route Processor Filler |
Release 6.1.2 |
|
ASR-9922-FAN-V2 |
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Version 2 Fan Tray |
Release 6.1.2 |
|
Cisco ASR 9006 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9006-SYS |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot System |
Release 6.1.2 |
|
ASR-9006-AC-V2 |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot AC Chassis Version 2 |
Release 6.1.2 |
|
ASR-9006-DC-V2 |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot DC Chassis Version 2 |
Release 6.1.2 |
|
ASR-9006-FAN |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Fan Tray |
Release 6.1.2 |
|
ASR-9006-DOOR |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Door Kit |
Release 6.1.2 |
|
ASR-9006-FILTER |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Air Filter |
Release 6.1.2 |
|
Cisco ASR 9906 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9906 |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot chassis |
Release 6.3.1 |
|
ASR-9906-FAN |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Fan Tray |
Release 6.3.1 |
|
ASR-9906-FILTER |
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Fan Filter |
Release 6.3.1 |
|
A99-SFC3-T |
ASR 9906 Switch Fabric Card |
Release 6.5.15 |
|
A99-SFC-T |
ASR 9906 Switch Fabric Card 3 |
Release 6.3.1 |
|
Cisco ASR 9010 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9010-SYS |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot System |
Release 6.1.2 |
|
ASR-9010-AC-V2 |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot AC Chassis Version 2 |
Release 6.1.2 |
|
ASR-9010-DC-V2 |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot DC Chassis Version 2 |
Release 6.1.2 |
|
ASR-9010-FAN |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Fan Tray |
Release 6.1.2 |
|
ASR-9010-DOOR |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Door Kit |
Release 6.1.2 |
|
ASR-9010-2P-KIT |
Cisco ASR 9000 Series Aggregation Services Router 2 Post Mounting Kit |
Release 6.1.2 |
|
ASR-9010-2P-KIT |
Cisco ASR 9000 Series Aggregration Services Router 4 Post Mounting Kit |
Release 6.1.2 |
|
ASR-9010-FILTER |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Air Filter |
Release 6.1.2 |
|
Cisco ASR 9910 Router |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
ASR-9910 |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot (9910) System |
Release 6.2.1 |
|
ASR-9910-FAN |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot(9910) Fan Tray |
Release 6.2.1 |
|
ASR-9910-ACC-KIT |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot (9910) Accessory Kit |
Release 6.2.1 |
|
ASR-9910-4P-KIT |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot (9910) 4 Post Rack Mounting Kit |
Release 6.2.1 |
|
ASR-9910-2P-KIT |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot (9910) 2 Post Rack Mounting Kit |
Release 6.2.1 |
|
ASR-9910-AIRREF |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot (9910) Air Reflector |
Release 6.2.1 |
|
ASR-9910-FILTER |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot (9910) Air Filter |
Release 6.2.1 |
|
A99-SFC-S |
Cisco ASR 9000 Series Aggregation Services Router 10-Slot (9910) Switch Fabric Card |
Release 6.2.1 |
|
A99-SFC3-S |
ASR 9910 Switch Fabric Card 3 |
Release 6.5.15 |
|
Cisco ASR 9000 Series Aggregation Services Router - Power Modules |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
PWR-2KW-DC-V2 |
Cisco ASR 9000 Series Aggregation Services Router 2KW DC Power Module, version 2 |
Release 6.1.2 |
|
PWR-3KW-AC-V2 |
Cisco ASR 9000 Series Aggregation Services Router 3KW AC Power Module, version 2 |
Release 6.1.2 |
|
A9K-AC-PEM-V2 |
Cisco ASR 9000 Series Aggregation Services Router AC Power Entry Module Version 2 |
Release 6.1.2 |
|
A9K-DC-PEM-V2 |
Cisco ASR 9000 Series Aggregation Services Router DC Power Entry Module Version 2 |
Release 6.1.2 |
|
A9K-PEM-V2-FILR |
Cisco ASR 9000 Series Aggregation Services Router Power Entry Module Version 2 Filler |
Release 6.1.2 |
|
A9K-AC-PEM-V3 |
Cisco ASR 9000 Series Aggregation Services Router AC Power Enclosure Module Version 3 |
Release 6.1.2 |
|
A9K-DC-PEM-V3 |
Cisco ASR 9000 Series Aggregation Services Router DC Power Enclosure Module Version 3 |
Release 6.1.2 |
|
PWR-6KW-AC-V3 |
Cisco ASR 9000 Series Aggregation Services Router 6kW AC Power Module Version 3 |
Release 6.1.2 |
|
PWR-4.4KW-DC-V3 |
Cisco ASR 9000 Series Aggregation Services Router 4.4kW DC Power Module Version 3 |
Release 6.1.2 |
|
PWR-1.6KW-AC |
ASR 9900 Fixed Chassis AC Power Supply |
Release 7.1.25 |
|
PWR-1.6KW-DC |
ASR 9900 Fixed Chassis DC Power Supply |
Release 7.1.25 |
|
Cisco ASR 9000 Series Aggregation Services Router - Line Cards |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
A9K-4HG-FLEX-SE |
ASR 9000 400GE Combo Service Edge Line Card - 5th Generation |
Release 7.4.1 |
|
A9K-4HG-FLEX-TR |
ASR 9000 400GE Combo Packet Transport Line Card - 5th Generation |
Release 7.4.1 |
|
A99-4HG-FLEX-SE |
ASR 9900 400GE Combo Service Edge Line Card - 5th Generation |
Release 7.4.1 |
|
A99-4HG-FLEX-TR |
ASR 9900 400GE Combo Packet Transport Line Card - 5th Generation |
Release 7.4.1 |
|
A9903-8HG-PEC |
ASR 9903 800G Multi-rate Port Expansion Card |
Release 7.4.1 |
|
A99-10X400GE-X-SE |
ASR 9900 4T Service Edge Line Card - 5th Generation |
Release 7.3.1 |
|
A99-10X400GE-X-TR |
ASR 9900 4T Packet Transport Line Card - 5th Generation |
Release 7.3.1 |
|
A9903-20HG-PEC |
ASR 9903 2T Multi-rate Port Expansion Card |
Release 7.1.3 |
|
A99-32X100GE-X-SE |
ASR 9000 32-Port 100GE QSFP28/QSFP+ Service Edge optimized Line Card - 5th Generation |
Release 7.1.15 |
|
A99-32X100GE-X-TR |
ASR 9000 32-Port 100GE QSFP28/QSFP+ Packet Transport optimized Line Card - 5th Generation |
Release 7.1.15 |
|
A9K-20HG-FLEX-SE A9K-20HG-FLEX-TR |
ASR 9000 2T Combo Line Card - 5th Generation |
Release 7.1.15 |
|
A9K-8HG-FLEX-SE A9K-8HG-FLEX-TR |
ASR 9000 800G Combo Line Card - 5th Generation |
Release 7.1.15 |
|
A9K-16X100GE-TR |
ASR 9000 16-port 100GE QSFP TR line card |
Release 6.5.15 |
|
A99-32X100GE-TR |
ASR 9900 32-port 100GE QSFP TR line card |
Release 6.5.15 |
|
A99-48X10GE-1G-SE |
ASR 9000 48 port dual rate 10G/1G Service Edge line card |
Release 6.5.2 |
|
A99-48X10GE-1G-TR |
ASR 9000 48 port dual rate 10G/1G Transport Optimised line card |
Release 6.5.2 |
|
A99-16X100GE-X-SE |
ASR 9900 16-port 100GE QSFP SE |
Release 6.5.3 |
|
A9K-48X10GE-1G-CM |
ASR 9000 48-port dual-rate 10G/1G Consumption Model line card |
Release 6.4.1 |
|
A9K-24X10GE-1G-CM |
ASR 9000 24-port dual-rate 10G/1G Consumption Model line card |
Release 6.4.1 |
|
A9K-4X100GE |
ASR 9000 4-port 100-Gigabit Ethernet Line Card |
Release 6.4.1 |
|
A9K-48X10GE-1G-SE |
ASR9000 48-port dual-rate 10G/1G service edge–optimized line card |
Release 6.3.2 |
|
A9K-48X10GE-1G-TR |
ASR9000 48-port dual-rate 10G/1G packet transport–optimized line card |
Release 6.3.2 |
|
A9K-24X10GE-1G-SE |
ASR9000 24-port dual-rate 10G/1G service edge–optimized line card |
Release 6.3.2 |
|
A9K-24X10GE-1G-TR |
ASR9000 24-port dual-rate 10G/1G packet transport–optimized line card |
Release 6.3.2 |
|
A99-8X100GE-SE |
ASR 9900 8-port 100GE Service Edge optimized |
Release 6.1.2 |
|
A99-8X100GE-TR |
ASR 9900 8-port 100GE Packet Transport optimized |
Release 6.1.2 |
|
A99-8X100GE-CM |
ASR 9900 8-port 100GE Consumption Model |
Release 6.1.2 |
|
A99-12X100GE |
Cisco ASR 9000 Series Aggregation Services Router 12-Port 100-Gigabit Ethernet Line Card |
Release 6.1.2 |
|
A99-12X100GE-CM |
Cisco ASR 9000 Series Aggregation Services Router 12-port 100GE Ethernet Line card CM |
Release 6.1.2 |
|
A9K-8X100GE-CM |
Cisco ASR 9000 Series Aggregation Services Router 8-Port 100- Gigabit Ethernet, Consumption Model Optimized with CPAK |
Release 6.1.2 |
|
A9K-8X100GE-SE |
Cisco ASR 9000 Series Aggregation Services Router 8-Port 100- Gigabit Ethernet, Service Edge Optimized |
Release 6.1.2 |
|
A9K-8X100GE-TR |
Cisco ASR 9000 Series Aggregation Services Router 8-Port 100-Gigabit Ethernet, Packet Transport Optimized |
Release 6.1.2 |
|
A9K-4X100GE-SE |
Cisco ASR 9000 Series Aggregation Services Router 4--Port 100-Gigabit Ethernet, Service Edge Optimized |
Release 6.1.2 |
|
A9K-4X100GE-TR |
Cisco ASR 9000 Series Aggregation Services Router 4-Port 100- Gigabit Ethernet, Packet Transport Optimized |
Release 6.1.2 |
|
Cisco ASR 9000 Series Aggregation Services Router - Modular Line Cards |
||
|
Part Number |
Cisco ASR 9000 Series Aggregation Services Router 200 Gigabit Modular Line Card, Packet Transport Optimized Cisco ASR 9000 Series Aggregation Services Router 200 Gigabit Modular Line Card, Service Edge Optimized |
Support Initially Provided in IOS XR 64 bit Release |
|
A9K-MOD200-TR A9K-MOD200-SE |
Cisco ASR 9000 Modular 400G Consumption Model Line Card |
Release 6.3.1 |
|
A9K-MOD400-CM |
Cisco ASR 9000 Series Aggregation Services Router 400 Gigabyte Modular Line Card, Service Edge Optimized |
Release 6.2.1 |
| A9K-MOD400-SE |
Cisco ASR 9000 Series Aggregation Services Router 400 Gigabyte Modular Line Card, Packet Transport Optimized |
Release 6.2.1 |
|
A9K-MOD400-TR |
Cisco ASR 9000 Series Aggregation Services Router 200 Gigabit Modular Line Card, Packet Transport Optimized Cisco ASR 9000 Series Aggregation Services Router 200 Gigabit Modular Line Card, Service Edge Optimized |
Release 6.2.1 |
|
Cisco ASR 9000 Series Aggregation Services Router - Modular Port Adapters (MPAs) |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
A9K-MPA-1X200GE |
Cisco ASR 9000 1-port 200-Gigabit Ethernet MPA, requires CFP2-DCO optics |
Release 6.6.2 |
|
A9K-MPA-32X1GE |
Cisco ASR 9000 32-port 1-Gigabit Ethernet MPA with MACSec |
Release 6.6.2 |
|
A9K-MPA20X10GE-CM |
Cisco ASR 9000 20x10GE Consumption Model MPA |
Release 6.5.1 |
|
A9K-MPA2X100GE-CM |
Cisco ASR 9000 2x100GE Consumption Model MPA |
Release 6.5.1 |
|
A9K-MPA-1X100GE |
Cisco ASR 9000 Series Aggregation Services Router 1-port 100-Gigabit Modular Port Adapter |
Release 6.3.1 |
|
A9K-MPA-2X100GE |
Cisco ASR 9000 Series Aggregation Services Router 2-port 100-Gigabit Modular Port Adapter |
Release 6.2.2 |
|
A9K-MPA-20x10GE |
20-Port 10-Gigabit Ethernet Modular Port Adapter with SFP+ |
Release 6.2.1 |
|
A9K-MPA-8X10GE |
Cisco ASR 9000 Series Aggregation Services Router 8-port 10GE Modular Port Adapter |
Release 6.3.2 |
|
A9K-MPA-4X10GE |
Cisco ASR 9000 Series Aggregation Services Router 4-port 10GE Modular Port Adapter |
Release 6.2.1 |
|
A9K-MPA-20X1GE |
Cisco ASR 9000 Series Aggregation Services Router 20-port 1GE Modular Port Adapter |
Release 6.2.1 |
|
A9K-MPA-2X40GE |
Cisco ASR 9000 Series Aggregation Services Router 2-port 40GE Modular Port Adapter |
Release 6.3.1 |
|
Cisco Digital Pluggable Optical Modules |
||
|
CFP2-WDM-DET-1HL= |
200G, 100G, WDM Digital CFP2 pluggable Licensed for 100G only – TOF |
Release 6.6.2 |
|
CFP2-WDM-D-1HL= |
200G, 100G, WDM Digital CFP2 pluggable Licensed for 100G only – NON TOF |
Release 6.6.2 |
|
Cisco ASR 9000v Satellite Shelf |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
A9KV-V2-DC-A= |
Cisco ASR 9000v Satellite Shelf Version 2 DC power ANSI chassis |
Release 6.2.1 |
|
A9KV-V2-DC-E= |
Cisco ASR 9000v Satellite Shelf Version 2 DC power chassis |
Release 6.2.1 |
|
A9KV-V2-AC= |
Cisco ASR 9000v Satellite Shelf AC power chassis |
Release 6.2.1 |
|
A9KV-V2-FAN= |
Cisco ASR 9000v Satellite Shelf Version 2 Fan Tray |
Release 6.2.1 |
|
Cisco NCS 5000 Satellite Shelf |
||
|
Part Number |
Description |
Support Initially Provided in IOS XR 64 bit Release |
|
NCS-5001 |
Cisco NCS 5001 Series Router |
Release 6.2.1 |
|
NCS-5002 |
Cisco NCS 5002 Series Router |
Release 6.2.1 |
|
NCS-5001-ACSR |
Cisco NCS 5001 Router Accessory Kit |
Release 6.2.1 |
|
NCS-5002-ACSR |
Cisco NCS 5002 Router Accessory Kit |
Release 6.2.1 |
|
NCS-5001-FN-BK |
Cisco NCS 5001 Router Fan Back to Front AirFlow |
Release 6.2.1 |
|
NCS-5002-FN-BK |
Cisco NCS 5002 Router Fan Back to Front AirFlow |
Release 6.2.1 |
|
NCS-5001-FLT-BK |
Cisco NCS 5001 Air Filter Back to Front Airflow |
Release 6.2.1 |
|
NCS-5002-FLT-BK |
Cisco NCS 5002 Air Filter Back to Front Airflow |
Release 6.2.1 |
|
NCS-5001-FN-FR |
Cisco NCS 5001 Fan Front to Back Airflow |
Release 6.2.1 |
|
NCS-5002-FN-FR |
Cisco NCS 5002 Fan Front to Back Airflow |
Release 6.2.1 |
|
NCS-5001-FLT-FR |
Cisco NCS 5001 Air Filter Front to Back Airflow |
Release 6.2.1 |
|
NCS-5002-FLT-FR |
Cisco NCS 5002 Air Filter Front to Back Airflow |
Release 6.2.1 |
Important Notes
-
Repetitive Smart Licensing evaluation expired warning messages are displayed on the console every hour, but no functionality impact is observed on the device. To stop these repetitive messages, you should register the device again with a new registration token.
-
From IOS XR Release 7.0, 1st and 2nd generation of Ethernet ASR 9000 line cards are not supported.
-
Country-specific laws, regulations, and licenses—In certain countries, use of these products may be prohibited and subject to laws, regulations, or licenses, including requirements applicable to the use of the products under telecommunications and other laws and regulations; customers must comply with all such applicable laws in the countries in which they intend to use the products.
-
Exceeding Cisco testing—If you intend to test beyond the combined maximum configuration tested and published by Cisco, contact your Cisco Account Team or Technical Support representative to discuss how to engineer a large-scale configuration for your purpose.
-
Installing a Line Card—For a fully populated Line Card with cable optics, maintenance time required for card replacement is higher. For more information about Line Card installation and removal, refer to the Cisco ASR 9000 Aggregation Services Router Ethernet Line Card Installation Guide.
-
For ZTP, In Cisco IOS XR Release 7.3.1 and earlier, the system accepts the device sending user-class = "exr-config"; however starting Cisco IOS XR Release 7.3.2 and later, you must use only user-class = "xr-config".
In Cisco IOS XR Release 7.3.2 and later, use:
host cisco-rp0 { hardware ethernet e4:c7:22:be:10:ba; fixed-address 172.30.12.54; if exists user-class and option user-class = "iPXE" { filename = "http://172.30.0.22/boot.ipxe"; } elsif exists user-class and option user-class = "xr-config" { filename = "http://172.30.0.22/scripts/cisco-rp0_ztp.sh"; } }
Supported Transceiver Modules
To determine the transceivers that Cisco hardware device supports, refer to the Transceiver Module Group (TMG) Compatibility Matrix tool.
Supported Modular Port Adapters
For the compatibility details of Modular Port Adapters (MPAs) on the line cards, see the datasheet of that specific line card.
Production Software Maintenance Updates (SMUs)
A production SMU is a SMU that is formally requested, developed, tested, and released. Production SMUs are intended for use in a live network environment and are formally supported by the Cisco TAC and the relevant development teams. Software bugs identified through software recommendations or Bug Search Tools are not a basis for production SMU requests.
For information on production SMU types, refer the Production SMU Types section of the IOS XR Software Maintenance Updates (SMUs) guide.
Upgrading Cisco IOS XR Software
Cisco IOS XR Software is installed and activated from modular packages, allowing specific features or software patches to be installed, upgraded, or downgraded without affecting unrelated processes. Software packages can be upgraded or downgraded on all supported card types, or on a single card (node).
Software packages are installed from Route Processor Module (RPM) files that contain one or more software components.
The upgrade document is available along with the software images.
Note |
If you have mLACP/ICCP Redundancy Model setup, ensure that you upgrade the active and standby nodes to the same IOS XR version while upgrading to a newer version of the ASR 9000 router. |
Cisco IOS XR Error messages
To view, search, compare, and download Cisco IOS XR Error Messages, refer to the Cisco IOS XR Error messages tool.
Cisco IOS XR MIBs
To determine the MIBs supported by platform and release, refer to the Cisco IOS XR MIBs tool.
Related Documentation
The most current Cisco ASR 9000 router documentation is located at the following URL:
https://www.cisco.com/c/en/us/td/docs/iosxr/asr-9000-series-routers.html
Feedback