P-LTE 450 Support

Support for P-LTE-450

The P-LTE-450 is a 450MHz Category-4 LTE PIM, which addresses LTE use cases primarily targeting utility, public safety, and critical infrastructure maintained by public organizations in Europe and other world regions. The module supports only Band 31 and 72 for LTE 450MHz networks.


Note


Throughout the user documentation, you will see the module referred to as P-LTE-450, which is the Cisco product name. The module is designed and manufactured by Intelliport, which refers to it as the IPS-701. Both names will be present in documentation.

Unlike regular LTE modules, there are some differences with regards to the P-LTE-450MHz on IOS-XE platform. Some of the key differences are:

  • IP pass through will be on Gigabit Ethernet interfaces rather than cellular interface

  • Troubleshooting commands are from web interface of third-party hardware

See the Cellular Pluggable Interface Module Configuration Guide for complete details.

For additional information, see the LTE 450MHz Alliance.

Support for P-LTE-450 Pluggable Interface Module

The Cisco Catalyst IR1800 Rugged Series Router now supports the 450MHz category P Long-Term Evolution (LTE) Pluggable Interface Module (PIM), referred to as P-LTE-450. The LTE-450 PIM uses the 450MHz frequency to address LTE use cases primarily targeting utility, public safety, and critical infrastructure maintained by public organizations in Europe and other countries. The module supports only Band 31 and 72, which are the LTE operating frequency bands. Due to hardware limitations, P-LTE-450 is supported only on slot 0/4.

Unlike regular LTE modules, the P-LTE-450 has some differences on the IOS-XE platform. Some of the key differences are:

  • IP pass through is on Gigabit Ethernet interfaces rather than cellular interfaces.

  • Troubleshooting commands are from the Web user interface of third-party hardware.


Note


Throughout the user documentation, you can see the module referred to as P-LTE-450, the Cisco product name. The module is designed and manufactured by Intelliport, which refers to it as the IPS-701. Both names are present in the documentation.


The show command output displays interface details:

router#show run | sec 0/4/0
interface GigabitEthernet0/4/0
ip address dhcp
negotiation auto
ipv6 dhcp client request vendor
ipv6 address autoconfig
ipv6 enable
interface GigabitEthernet0/4/0.2
encapsulation dot1Q 2
ip address dhcp
ipv6 dhcp client request vendor
ipv6 address autoconfig
 
router#show ip int br
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 10.195.236.86 YES NVRAM up up
GigabitEthernet0/1/0 unassigned YES unset down down
GigabitEthernet0/1/1 unassigned YES unset down down
GigabitEthernet0/1/2 unassigned YES unset up up
GigabitEthernet0/1/3 unassigned YES unset down down
Wl0/1/4 unassigned YES unset up up
GigabitEthernet0/4/0 192.168.200.194 YES DHCP up up
GigabitEthernet0/4/0.2 192.168.4.6 YES DHCP up up
GigabitEthernet0/4/0.3 192.168.5.2 YES DHCP up up
Async0/2/0 unassigned YES unset up down
Vlan1 192.168.50.1 YES NVRAM up up

For more information on how to configure the router interface for the P-LTE-450 module, See

VRF for the P-LTE-450 Module

Virtual Routing Forwarding (VRF) for the LTE450 module creates a separate routing table. This isolates LTE450 traffic, such as monitoring, management, or dedicated data flows. It ensures segregation from other network services on the device.

Starting from IOS-XE 17.18.1a, you can enable VRF to provision LTE450 parameters through the LTE450 management interface. You can enable VRF on 450 PIM management interface to enable HTTP request from router to the webserver of P-LTE-450, and get response from the webserver of P-LTE-450.

Table 1. Feature History Table

Feature

Release Information

Feature Description

VRF for the P-LTE-450 Module

IOS-XE 17.18.1a

You can now enable VRF to provision LTE450 parameters through the LTE450 management interface.

You can also enable VRF on 450 PIM management interface to enable HTTP request from router to the webserver of P-LTE-450 and get response from the webserver of P-LTE-450.

Configure VRF for the P-LTE-450 module

Perform these steps to configure VRF for the P-LTE-450 module.

Procedure


Step 1

Use the configure command to enter the global configuration mode.

Example:

Router# configure

Step 2

Use the vrf definition command to create a VRF.

Example:

Router(config)# vrf definition lte450_mgmt 

Step 3

Use the address-family command to to set the address family to either IPv4 or IPv6 for traffic routing.

Example:

Router(config-vrf-lte450_mgmt)# address-family ipv4

Step 4

Use the exit-address-family command to exit from the address family configuration mode.

Example:

Router(config-vrf-lte450_mgmt-address-family)# exit-address-family 

Step 5

Use the exit command to exit from the VRF configuration mode.

Example:

Router(config-vrf-lte450_mgmt)# exit 

Step 6

Use the interface command to configure LTE450 management interface.

Example:

Router(config)# interface GigabitEthernet0/1/0 

Step 7

Use the description command to add a description to the interface.

Example:


Router(config-if)# description LTE450 Management Interface 

Step 8

Use the vrf forwarding command to associate the LTE 450 management interface with a VRF for traffic routing.

Example:


Router(config-if)# vrf forwarding lte450_mgmt 

Step 9

Use the ip address dhcp command for the main interface to retrieve the management address.

Example:


Router(config-if)# ip address dhcp 

Step 10

Use the negotiation auto command to configure auto-negotiation to handle different speeds on hardware.

Example:

Router(config-if)# negotiation auto 

Step 11

Use the lte450 band command to configure the LTE 450 MHz modem band value.

Example:

Router(config-if)# lte450 band 31
/* Possible values are 31 or 72*/

Step 12

Use the end commad to save and exit the configuration.

Example:

Router(config-if)# end 

P-LTE-450 Support on Autonomous Mode

This release introduces two modes of setting the required credentials to communicate with the module. The username and password that should be used in these CLIs can be found on the sticker label that comes with the P-LTE-450 module.


Important


You MUST set the username and password before performing any P-LTE-450 parameter configuration.

Configuration

The recommended configuration is through the Config mode:

interface GigabitEthernet 0/1/0
lte450 credential username username password password

Using the Exec mode:

hw-module subslot 0/1 lte450 set-info username username password password [encrypt]

Note


Execution of this command will create a file called bootflash:lte450.info and should not be deleted.

P-LTE-450 Support Over SDWAN/vManage

The P-LTE-450 is a 450MHz Category-4 LTE PIM, which addresses LTE use cases primarily targeting utility, public safety, and critical infrastructure maintained by public organizations in Europe and other world regions. The module supports only Band 31 and 72 for LTE 450MHz networks.

Support for the P-LTE-450 was introduced in IOS XE 17.12.1a. This release introduces support for the P-LTE-450 over SDWAN /vManage.

Guidelines and Limitations

The following are the limitations of the P-LTE-450 with SDWAN/vManage:

  • No PNP support on P-LTE-450 as a primary link.

  • P-LTE-450 parameter configuration is only supported with CLI templates.

  • P-LTE-450 credential configuration via vManage is not supported on this release. Will be supported in the vManage 20.16 release.

Additional Documentation

Additional documentation for SDWAN/vManage is available at the following links:

Enhancing P-LTE-450 Network Management Through SNMP MIB Objects

In P-LTE-450 networks, routers can provide crucial quality metrics through Simple Network Management Protocol (SNMP) Management Information Base (MIB) objects. Specifically, Cisco IR1101 and IR1800 routers equipped with the P-LTE-450 Pluggable Interface Module (PIM) allows you to integrate seamlessly with existing SNMP-based management tools to report their status and quality metrics.

The router identifies the P-LTE-450 module as an Ethernet interface, specifically Gigabit Ethernet 0/1/0, rather than a cellular interface.. For LTE450 0/1/0 radio parameters to be supported through SNMP, a new MIB file named Cisco-LTE450-MIB.my needs to be created. This MIB file includes specific fields to capture radio signal quality metrics.

Supported SNMP MIBs

The CISCO-LTE450-MIB SNMP is supported on Cisco P_ LTE_450 MIB .

CISCO-LTE450-MIB supports the following MIB fields:

  • `CiscoLte450Entry `: Main entry point for the MIB

  • `ciscoLte450PortIndex `: Index for the port (GigabitEthernet0/1/0)

  • `ciscoLte450Rssi `: RSSI value

  • `ciscoLte450Rsrp `: RSRP value

  • `ciscoLte450Rsrq `: RSRQ value

  • `ciscoLte450Sinr `: SINR value

  • `ciscoLte450RssiMain `: RSSI value for the main antenna

  • `ciscoLte450RsrpMain `: RSRP value for the main antenna

  • `ciscoLte450RssiAux `: RSSI value for the auxiliary antenna

  • `ciscoLte450RsrpAux `: RSRP value for the auxiliary antenna

View Radio Signal Quality Metrics

The following example displays the signal quality and antenna signal quality of SNMP Cisco 4G LTE 450 configuration:

Router#show lte450 0/1/0 radio
Signal quality
==============
RSSI = -88 dBm
RSRP = -114 dBm
RSRQ = -12 dB
SINR = 0 dB

Antenna signal quality
======================
Main RSSI = -87 dBm
Main RSRP = -112 dBm
Aux RSSI = -104 dBm
Aux RSRP = -143 dBm