show fpd package
To display which shared port adapters (SPA) and SPA interface processors (SIPs) are supported with your current Cisco IOS XR software release, which field-programmable device (FPD) image you need for each SPA and SIP, and what the minimum hardware requirements are for the SPA and SIP modules, use the show fpd package command in administration EXEC mode.
show fpd package
Syntax Description
This command has no keywords or arguments.
Command Default
No default behavior or values
Command Modes
System Admin EXEC
Command History
Release |
Modification |
---|---|
Release 5.0.0 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
If there are multiple FPD images for your card, use the show fpd package command to determine which FPD image to use if you only want to upgrade a specific FPD type.
Task ID
Task ID |
Operations |
---|---|
sysmgr |
read |
Examples
The following example shows a sample output from the show fpd package command:
Router#show fpd package
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
8201 Bios YES 1.23 1.23 0.0
BiosGolden YES 1.23 1.15 0.0
IoFpga YES 1.11 1.11 0.1
IoFpgaGolden YES 1.11 0.48 0.1
SsdIntelS3520 YES 1.21 1.21 0.0
SsdIntelS4510 YES 11.32 11.32 0.0
SsdMicron5100 YES 7.01 7.01 0.0
SsdMicron5300 YES 0.01 0.01 0.0
x86Fpga YES 1.05 1.05 0.0
x86FpgaGolden YES 1.05 0.48 0.0
x86TamFw YES 5.13 5.13 0.0
x86TamFwGolden YES 5.13 5.05 0.0
--------------------------------------------------------------------------------
8201-ON Bios YES 1.208 1.208 0.0
BiosGolden YES 1.208 1.207 0.0
IoFpga YES 1.11 1.11 0.1
IoFpgaGolden YES 1.11 0.48 0.1
SsdIntelS3520 YES 1.21 1.21 0.0
SsdIntelS4510 YES 11.32 11.32 0.0
SsdMicron5100 YES 7.01 7.01 0.0
SsdMicron5300 YES 0.01 0.01 0.0
x86Fpga YES 1.05 1.05 0.0
x86FpgaGolden YES 1.05 0.48 0.0
x86TamFw YES 5.13 5.13 0.0
x86TamFwGolden YES 5.13 5.05 0.0
--------------------------------------------------------------------------------
8201-SYS Bios YES 1.23 1.23 0.0
BiosGolden YES 1.23 1.15 0.0
Examples
This table describes the significant fields shown in the display:
Field |
Description |
---|---|
Card Type |
Module part number. |
FPD Description |
Description of all FPD images available for the line card. |
Type |
Hardware type. Possible types can be:
|
Subtype |
FPD subtype. These values are used in the upgrade hw-module fpd command to indicate a specific FPD image type to upgrade. |
SW Version |
FPD software version recommended for the associated module running the current Cisco IOS XR software. |
Min Req SW Vers |
Minimum required FPD image software version to operate the card. Version 0.0 indicates that a minimum required image was not programmed into the card. |
Min Req HW Vers |
Minimum required hardware version for the associated FPD image. A minimum hardware requirement of version 0.0 indicates that all hardware can support this FPD image version. |
![]() Note |
In the show fpd package command output, the “subtype” column shows the FPDs that correspond with each line card image. To upgrade a specific FPD with the upgrade hw-module fpd command, replace the fpga-type argument with the appropriate FPD from the “subtype” column, as shown in the following example:
|