The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
EPLD Versions in Cisco MDS 9000 EPLD Bundle
Note: Release notes are sometimes updated with new information. Refer to the following website for the most recent version of the Cisco MDS 9000 Series Release Notes: http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-release-notes-list.html
Switches and directors in the Cisco MDS 9000 Series contain several electrical programmable logical devices (EPLDs) that provide hardware functionalities in all the modules. EPLD upgrades are periodically provided to include enhanced hardware functionality or to resolve known issues.
EPLD bundles are released as part of a Cisco MDS NX-OS release. Therefore, the EPLD bundles have a version number that matches the Cisco MDS NX-OS release they are part of.
An EPLD bundle is a package containing updates for multiple EPLDs. Each EPLD update has its own version number, which is independent of the Cisco MDS NX-OS release. As EPLD changes are infrequent, an EPLD bundle may contain new updates for only some EPLDs. The remaining EPLD updates will be the same version as the previous EPLD bundle.
You need not update switch EPLDs unless otherwise advised by TAC. For detailed functional image upgrade instructions, refer to the Cisco MDS 9000 NX-OS Fundamentals Configuration Guide.
Date |
Description |
January 25, 2022 |
Release 9.2(2) became available. |
The version of the EPLD bundle must match the version of Cisco MDS NX-OS release that is running when the EPLD upgrades are installed. This requirement only applies during EPLD code upgrade or downgrade. Cisco MDS NX-OS can be subsequently upgraded or downgraded without changing the EPLD versions. The below table shows the EPLD bundles that are compatible with specific NX-OS releases.
Table 1. Release Compatibility Matrix
The below table lists the Cisco MDS 9000 components and the EPLD bundle versions that are supported for the components.
Table 2. Cisco MDS 9000 EPLD Bundle Versions
m9000-pkg2.9.2.2.epld [1] |
||
EPLD Versions in Cisco MDS 9000 EPLD Bundle
Each EPLD bundle that you can download from http://www.cisco.com is a bundle of EPLD upgrades. The below table lists the EPLD versions for Cisco MDS 9000 series platforms for Cisco MDS NX-OS Release 9.2(2).
Module Type |
EPLD Device |
Version |
|
MDS 9124V Fibre Channel Fabric Switch |
|||
DS-C9124V-K9-SUP |
24-Port 8/16/32/64-Gbps 1-RU Fabric Switch |
MI IO SPI |
0.012 |
IO SPI 2 |
0.014 |
||
MDS 9132T Fibre Channel Fabric Switch |
|||
DS-C9132T |
32-Port 4/8/16/32-Gbps 1-RU Fabric Switch |
IO SPI 2 |
0.024 |
MI IO SPI |
0.017 |
||
LEM IO SPI |
0.016 |
||
MDS 9148S Fibre Channel Fabric Switch |
|||
DS-C9148S-K9 |
48-Port 2/4/8/16-Gbps Fabric Switch |
Power Manager |
0x1f |
MDS 9148T Fibre Channel Fabric Switch |
|||
DS-C9148T-K9 |
48-Port 4/8/16/32-Gbps 1-RU Fabric Switch |
SFP SPI |
0.01 |
IO SPI 2 |
0.01 |
||
MI IO SPI |
0.01 |
||
MDS 9148V Fibre Channel Fabric Switch |
|||
DS-C9148V-K9-SUP |
48-Port 8/16/32/64-Gbps 1-RU Fabric Switch |
MI IO SPI |
0.012 |
IO SPI 2 |
0.014 |
||
MDS 9220i Multiservice Fabric Switch |
|||
DS-C9220I-K9 |
4/8/16/32-Gbps 1-RU Fabric Switch |
IO SPI 2 |
0.024 |
MI IO SPI |
0.027 |
||
AKFPGA SPI |
1 |
||
MDS 9250i Multiservice Fabric Switch |
|||
DS-C9250I-K9 |
40-Port 2/4/8/16-Gbps Fabric Switch |
Power Manager |
0x1a |
DB Power Manager |
0x0b |
||
MDS 9396S Fibre Channel Fabric Switch |
|||
DS-C9396S-K9 |
96-Port 2/4/8/16-Gbps Fabric Switch |
IO SPI 2 |
1.00 |
IO SPI |
1.00 |
||
MDS 9396T Fibre Channel Fabric Switch |
|||
DS-C9396T-K9 |
96-Port 4/8/16/32-Gbps 2-RU Fabric Switch |
SFP SPI |
0.007 |
IO SPI 2 |
0.013 |
||
MI IO SPI |
0.006 |
||
LEM-1 SPI |
0.016 |
||
LEM-2 SPI |
0.016 |
||
LEM-3 SPI |
0.016 |
||
MDS 9700 Series Common Modules |
|||
DS-X97-SF1-K9 |
Supervisor Module 3 |
Power Manager SPI |
22.00 |
DS-X97-SF1E-K9 |
Supervisor Module 3 |
Power Manager SPI |
22.00 |
DS-X97-SF4-K9 |
Supervisor Module 4 |
Power Manager SPI |
23.00 |
DS-X9448-768K9 |
48-Port 16-Gbps Advanced Fibre Channel Module |
Power Manager |
10.00 |
IO |
15.00 |
||
DS-X9648-1536K9 |
48-Port 32-Gbps Fibre Channel Switching Module |
Power Manager SPI |
0.002 |
SFP SPI |
0.005 |
||
IO SPI |
2.00 |
||
DS-X9748-3072K9 |
48-Port 64-Gbps Fibre Channel Switching Module |
SFP SPI |
0.008 |
IO SPI |
0.029 |
||
DS-X9824-960K9 |
40-Gbps FCoE Module |
Power Manager SPI |
1.01 |
IO SPI 2 |
0.03 |
||
IO SPI |
0.03 |
||
DS-X9848-480K9 |
10-Gbps FCoE Module |
Power Manager SPI |
0.01 |
IO |
0.01 |
||
DS-X9334-K9 |
24/10-Port SAN Extension Module |
Power Manager SPI |
1.001 |
IO SPI |
2.00 |
||
MDS 9706 Series Specific Modules |
|||
DS-C9706-FAN |
Fan |
Fan Controller (1) |
0.01 |
Fan Controller (2) |
0.01 |
||
DS-X9706-FAB-1 |
Fabric Module 1 |
Power Manager |
1.00 |
DS-X9706-FAB-3 |
Fabric Module 3 |
Power Manager |
0.01 |
MDS 9710 Series Specific Modules |
|||
DS-C9710-FAN |
Fan |
Fan Controller (1) |
0.01 |
Fan Controller (2) |
0.01 |
||
DS-X9710-FAB-1 |
Fabric Module 1 |
Power Manager |
1.00 |
DS-X9710-FAB-3 |
Fabric Module 3 |
Power Manager |
0.01 |
MDS 9718 Series Specific Modules |
|||
DS-C9718-FAN |
Fan |
Fan Controller (1) |
0.01 |
Fan Controller (2) |
0.01 |
||
DS-X9718-FAB-1 |
Fabric Module 1 |
Power Manager |
1.00 |
DS-X9718-FAB-3 |
Fabric Module 3 |
Power Manager |
0.01 |
This EPLD release contains minor hardware-related changes that do not change the product specification. For example, handling new versions of hardware electrical components on a new revision of a module. These changes are backward compatible with older hardware, but unnecessary unless specifically documented below.
There are no resolved issues in this release.
● When you upgrade or downgrade the EPLDs, observe the following guidelines and limitations:
● You can upgrade each module only when it is online. The EPLD upgrade is only disruptive to the module being upgraded.
● If you interrupt an EPLD upgrade or downgrade, the module must be upgraded again.
● In Cisco MDS 9000 Director Switches, EPLD upgrade or downgrade can only be executed from the active supervisor module. To upgrade the supervisor EPLDs nondisruptively, upgrade the standby supervisor and then switchover. After the new standby supervisor is online, its EPLDs can be upgraded.
● In Cisco MDS 9000 Series Fabric Switches, be sure to specify 1 as the module number. The switch must be power cycled for the EPLDs to start running the new code.
You can determine the EPLD versions currently installed in the hardware and also in EPLD images by using CLI commands. This section includes the following topics:
Use the show version module slot epld command to view all current EPLD versions on a specific module.
Example 1 Displaying Current EPLD Versions for a Module
switch# show version module 1 epld
---------------------------------------
Use the show version fan slot epld command to view all current EPLD versions on a specific fan module. The following command output shows the currently installed EPLD versions on a fan module.
Example 2 Displaying Current EPLD Versions for a Fan Module
switch# show version fan 1 epld
---------------------------------------
Use the show version xbar slot epld command to view all current EPLD versions on a specific fabric module. The following command output shows the currently installed EPLD versions on a fabric module.
Example 3 Displaying Current EPLD Versions for a Fabric Module
switch# show version xbar 2 epld
---------------------------------------
Displaying EPLD Versions in an EPLD Bundle
Use the show version epld uri command to view all the updates contained in an EPLD package. The following example shows the EPLD versions contained in an EPLD bundle stored in bootflash.
Example 4 Displaying EPLD Versions in an EPLD Bundle
switch# show version epld bootflash:m9000-pkg2.9.2.2.epld
Retrieving EPLD versions... Please wait.
EPLD image file 9.2.2 built on Sat Jan 15 02:29:42 2022
Module Type Model EPLD Device Version
-----------------------------------------------------------------------------
Supervisor Module-3 DS-X97-SF1-K9 Power Manager SPI 22.000
Supervisor Module-3 DS-X97-SF1E-K9 Power Manager SPI 22.000
Supervisor Module-4 DS-X97-SF4-K9 Power Manager SPI 23.000
Fabric Module 1 DS-X9718-FAB1 Power Manager 1.002
Fabric Module 1 DS-X9710-FAB1 Power Manager 1.003
Fabric Module 1 DS-X9706-FAB1 Power Manager 1.002
Fabric Module 3 DS-X9706-FAB-3 Power Manager 0.010
Fabric Module 3 DS-X9710-FAB-3 Power Manager 0.008
Fabric Module 3 DS-X9718-FAB-3 Power Manager 0.007
16 Gbps Advanced FC Module DS-X9448-768K9 Power Manager 10.000
16 Gbps Advanced FC Module DS-X9448-768K9 IO 15.000
10 Gbps FCoE Module DS-X9848-480K9 Power Manager 0.006
10 Gbps FCoE Module DS-X9848-480K9 IO 0.005
40 Gbps FCoE Module DS-X9824-960K9 Power Manager SPI 1.005
40 Gbps FCoE Module DS-X9824-960K9 IO SPI 2 0.028
40 Gbps FCoE Module DS-X9824-960K9 IO SPI 0.031
Fan DS-C9718-FAN Fan Controller (1) 0.006
Fan DS-C9718-FAN Fan Controller (2) 0.006
Fan DS-C9710-FAN Fan Controller (1) 0.006
Fan DS-C9710-FAN Fan Controller (2) 0.006
Fan DS-C9706-FAN Fan Controller (1) 0.006
Fan DS-C9706-FAN Fan Controller (2) 0.006
2/4/8/16G Fabric Switch DS-C9396S-K9 IO SPI 2 1.002
2/4/8/16G Fabric Switch DS-C9396S-K9 IO SPI 1.003
32 Gbps Advanced FC Module DS-X9648-1536K9 Power Manager SPI 0.002
32 Gbps Advanced FC Module DS-X9648-1536K9 SFP SPI 0.005
32 Gbps Advanced FC Module DS-X9648-1536K9 IO SPI 2.000
1/10/40G IPS,2/4/8/10/16G FC ModulDS-X9334-K9 Power Manager SPI 1.001
1/10/40G IPS,2/4/8/10/16G FC ModulDS-X9334-K9 IO SPI 2.000
4/8/16/32G 1 RU Fabric Switch DS-C9132T IO SPI 2 0.022
4/8/16/32G 1 RU Fabric Switch DS-C9132T MI IO SPI 0.017
4/8/16/32G 1 RU Fabric Switch DS-C9132T LEM IO SPI 0.016
4/8/16/32G 2 RU Fabric Switch DS-C9396T-K9 SFP SPI 0.007
4/8/16/32G 2 RU Fabric Switch DS-C9396T-K9 IO SPI 2 0.011
4/8/16/32G 2 RU Fabric Switch DS-C9396T-K9 MI IO SPI 0.005
4/8/16/32G 2 RU Fabric Switch DS-C9396T-K9 LEM-1 SPI 0.016
4/8/16/32G 2 RU Fabric Switch DS-C9396T-K9 LEM-2 SPI 0.016
4/8/16/32G 2 RU Fabric Switch DS-C9396T-K9 LEM-3 SPI 0.016
4/8/16/32G 1 RU Fabric Switch DS-C9148T-K9 SFP SPI 0.007
4/8/16/32G 1 RU Fabric Switch DS-C9148T-K9 IO SPI 2 0.011
4/8/16/32G 1 RU Fabric Switch DS-C9148T-K9 MI IO SPI 0.005
1/10/25/40G IPS, 4/8/16/32G FC SwiDS-C9220I-K9 IO SPI 2 0.024
1/10/25/40G IPS, 4/8/16/32G FC SwiDS-C9220I-K9 MI IO SPI 0.027
1/10/25/40G IPS, 4/8/16/32G FC SwiDS-C9220I-K9 AKFPGA SPI 1.000
8/16/32/64 Gbps Advanced FC ModuleDS-X9748-3072K9 SFP SPI 0.008
8/16/32/64 Gbps Advanced FC ModuleDS-X9748-3072K9 IO SPI 0.028
Supervisors, switching, fabric, and fan modules may be upgraded in a switch. For Director switches, modules can be upgraded together or individually. For Fabric switches, modules are upgraded individually. Fabric switches do not require fabric and fan modules to be upgraded.
The modules to be upgraded are specified by the user. If the module number that is specified in the command is not present, the update is aborted. Otherwise, a warning and a prompt to continue is printed. If the user proceeds, the status of each specified module is printed followed by a table of installed and new EPLD versions. If no modules require upgrading, the command exits. If any module EPLD version is different and requires upgrading, the user is prompted to continue. All EPLDs are updated on the first specified module. The update process may take several minutes. After the update, the module is power cycled. For switching modules, this power cycle disrupts traffic on all ports of the module. If the new EPLD version is the same as the installed version or the module is present but not online, no action is taken for that module. If more than one module is specified, the download and power cycle process is repeated for the next module.
Installing EPLD Updates on All Modules in a Director Switch
To update all EPLDs sequentially with a single command, use the install all epld command with the module all fan-module all xbar all options. After each module is upgraded, it is power cycled to load the EPLD update. Switching module power cycles are disruptive to the traffic passing through them. If the active supervisor requires upgrading, it will be updated last and a supervisor switchover executed. Fan modules do not require to be power cycled.
Installing a Director Switch Supervisor Module EPLD Update
To update the EPLDs on supervisor modules of Director Switches in a nondisruptive manner, follow these steps:
Step 1. Update the EPLD on the standby supervisor module. From the active supervisor module, enter the install all epld CLI command, specifying the current standby supervisor module number.
After the EPLD update is complete, the standby supervisor module will be power cycled.
Step 2. After the standby supervisor module reaches 'ha-standby' state, perform a switchover and wait until the new standby supervisor module reaches 'ha-standby' state.
Step 3. From the active supervisor module, repeat steps 1–3.
For information about how to update the EPLDs on supervisor modules of the Fabric switches, see Installing a Switching Module EPLD Update.
Example 5 Updating the Standby Supervisor Module EPLDs on a Cisco MDS 9700 Series Switch
switch# install all epld bootflash:m9000-pkg2-9.2.2.epld parallel module 6
Copy complete, now saving to disk (please wait)...
EPLD image signature verification passed
Module Type Upgradable Impact Reason
------ ---- ---------- ---------- ------
6 SUP Yes disruptive Module Upgradable
Retrieving EPLD versions... Please wait.
Images will be upgraded according to following table:
Module Type EPLD Running-Version New-Version Upg-Required
------ ---- ----------------- --------------- ----------- ------------
6 SUP Power Manager SPI 18.000 19.000 Yes
The above modules require upgrade.
Do you want to continue (y/n) ? [n] y
Starting Module 6 EPLD Upgrade
Module 6 : Power Manager SPI [Upgrade Started ]
Module 6 : Power Manager SPI [Erasing ] : 100.00%
Module 6 : Power Manager SPI [Programming ] : 100.00% (6020818 of 6020818 total bytes)
Waiting for Module 6 to come online.
Module 6 EPLD upgrade is successful.
Installing a Switching Module EPLD Update
For Director Switches, use the install all epld uri parallel module slot command to update the EPLDs on an individual module. Use the module all option to update the EPLDs of both supervisors and all switching modules.
Example 6 Updating Module EPLDs on a Director Switch
switch# install all epld bootflash:m9000-pkg2.9.2.2.epld parallel module 1
WARNING!!!: Executing the "install all epld" command
may result in multiple modules going offline and
For EPLD upgrade best practices, please refer below link:
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/7_3/upgrade/upgrade.html
Do you want to continue (y/n) ? [n] y
Copy complete, now saving to disk (please wait)...
EPLD image signature verification passed
Module Type Upgradable Impact Reason
------ ---- ---------- ---------- ------
1 LC Yes disruptive Module Upgradable
Retrieving EPLD versions... Please wait.
Images will be upgraded according to following table:
Module Type EPLD Running-Version New-Version Upg-Required
------ ---- ------------- --------------- ----------- ------------
1 LC Power Manager 10.000 10.000 No
*************************************
Installing a Fabric Switch Supervisor EPLD Update
Note: An EPLD update of the supervisor module of Fabric Switches (Cisco MDS 9100, Cisco MDS 9200, and Cisco MDS 9300 Series switches) is disruptive since there is no redundant supervisor to take over while the update is in progress. All traffic through the system is stopped while updating and the switch is power cycled after the upgrade has completed. The update may take up to 30 minutes to complete. The following message is displayed:
Data traffic on the switch will be affected!!
The switch will reload after the upgrade process.
Do you want to continue (y/n) ?
For more information about upgrading supervisor modules in Director Switches, see Installing a Director Switch Supervisor Module EPLD Update.
Example 7 Updating Supervisor EPLDs on a Fabric Switch
switch# install module 1 epld bootflash:m9000-pkg2-9.2.2.epld
Retrieving EPLD versions... Please wait.
Images will be upgraded according to following table:
Module Type EPLD Running-Version New-Version Upg-Required
------ ---- ------------- --------------- ----------- ------------
1 SUP IO SPI 2 0.005 1.002 Yes
Data traffic on the switch will be affected!!
The switch will reload after the upgrade process.
Do you want to continue (y/n) ? [n] y
Module 1 : IO SPI [Programming ] : 100.00% ( 12970 of 12970 total bytes)
Module 1 : IO SPI 2 [Programming ] : 100.00% ( 3137 of 3137 total bytes)
Waiting for Module to come online.
Module 1 EPLD upgrade is successful.
Reconfiguring Active Supervisor EPLDs.
Module 1 : IO SPI 2 [Programming ] : 0.70% ( 22 of 3137 total bytes)
Module 1 EPLD upgrade is successful.
Installing a Fan Module EPLD Update
Use the install all epld uri parallel fan-module slot command to upgrade the EPLDs on the fan modules. The EPLD update for a fan module is nondisruptive and a power cycle is not required after the update.
Example 8 Upgrading Fan Module EPLDs on a Cisco MDS 9700 Series Switch
switch# install all epld bootflash:m9000-pkg2.9.2.2.epld parallel fan-module 1
WARNING!!!: Executing the "install all epld" command
may result in multiple modules going offline and
It is strongly recommended to use one of the following
when EPLD upgrade is attempted on a system carrying
production traffic.or Module EPLDs".
1) "install module <mod#> epld"
2) "install all epld <uri> parallel module <mod#>"
where <mod#> is on a single module
For EPLD upgrade best practices, please refer to the link-
http://www.cisco.com/en/US/docs/switches/datacenter/
sw/best_practices/cli_mgmt_guide/epld_upgrade.html
Do you want to continue (y/n) ? [n] y
Copy complete, now saving to disk (please wait)...
EPLD image signature verification passed
Retrieving EPLD versions... Please wait.
Images will be upgraded according to following table:
Module Type EPLD Running-Version New-Version Upg-Required
------ ---- ------------------ --------------- ----------- ------------
1 FAN Fan Controller (1) 0.002 0.006 Yes
1 FAN Fan Controller (2) 0.002 0.006 Yes
Do you want to continue (y/n) ? [n] y
Fan 1 (1 of 2) : Fan Controller [Verifying ] : 100.00% ( 135658 of 135658 total bytes)
Fan 1 (2 of 2) : Fan Controller [Verifying ] : 100.00% ( 135658 of 135658 total bytes)
Waiting for Module to come online.
Fan Module 1 EPLD upgrade is successful.
Installing a Fabric Module EPLD Update
The Cisco MDS 9700 Series switches have dedicated fabric modules. These modules contain EPLDs, which can be upgraded as described in this section. All other Cisco MDS switches do not have these modules, so this process is not applicable for them.
For Cisco MDS 9700 Series switches, use the install all epld uri parallel xbar-module slot command to update the EPLDs on the fabric modules. This process power cycles the updated module. To ensure that the data traffic performance is not affected while the module is power cycled, check the fabric bandwidth utilization by using the show hardware fabric-utilization detail command. If there is adequate reserve fabric bandwidth available before the update starts, then the update will be nondisruptive.
Example 9 Upgrading Fabric Module EPLDs for a Cisco MDS 9700 Series Switch
switch# install all epld bootflash:m9000-pkg2.9.2.2.epld parallel xbar-module 1
WARNING!!!: Executing the "install all epld" command
may result in multiple modules going offline and
It is strongly recommended to use one of the following
when EPLD upgrade is attempted on a system carrying
1) "install module <mod#> epld"
2) "install all epld <uri> parallel module <mod#>"
where <mod#> is on a single module
For EPLD upgrade best practices, please refer to the link-
http://www.cisco.com/en/US/docs/switches/datacenter/
sw/best_practices/cli_mgmt_guide/epld_upgrade.html
Do you want to continue (y/n) ? [n] y
Copy complete, now saving to disk (please wait)...
EPLD image signature verification passed
Module Type Upgradable Impact Reason
------ ---- ---------- ---------- ------
1 Xbar Yes disruptive Module Upgradable
Retrieving EPLD versions... Please wait.
Images will be upgraded according to following table:
Module Type EPLD Running-Version New-Version Upg-Required
------ ---- ------------- --------------- ----------- ------------
1 Xbar Power Manager 1.003 1.004 Yes
The above modules require upgrade.
Do you want to continue (y/n) ? [n] y
Starting Xbar Module 1 EPLD Upgrade
Xbar Module 1 EPLD upgrade is successful.
The documentation set for the Cisco MDS 9000 Series includes the following documents.
http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-release-notes-list.html
Regulatory Compliance and Safety Information
http://www.cisco.com/en/US/docs/storage/san_switches/mds9000/hw/regulatory/compliance/RCSI.html
http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-device-support-tables-list.html
http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-installation-guides-list.html
Software Installation and Upgrade
http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-installation-guides-list.html
Cisco MDS NX-OS Configuration Guides
http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-installation-and-configuration-guides-list.html
Cisco DCNM-SAN Configuration Guides
http://www.cisco.com/c/en/us/support/cloud-systems-management/prime-data-center-network-manager/products-installation-and-configuration-guides-list.html
http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-command-reference-list.html
Intelligent Storage Networking Services Configuration Guides
http://www.cisco.com/c/en/us/support/storage-networking/mds-9000-nx-os-san-os-software/products-installation-and-configuration-guides-list.html
● Cisco MDS 9000 Series and Nexus 7000 Series System Messages Reference
● Cisco MDS 9000 Series SAN-OS Troubleshooting Guide
● Cisco MDS 9000 Series MIB Quick Reference
● Cisco DCNM for SAN Database Schema Reference
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Copyright © 2022 Cisco Systems, Inc. All rights reserved.