Cisco Nexus 9000 ACI-Mode Switches Release Notes, Release 14.2(3)

July 19, 2022

In the Open Issues section, added bugs CSCwb17229 and CSCwb39899.

May 16, 2022

In the Open Issues section, added bug CSCwa47686.

March 16, 2022

In the Open Issues section, added bugs CSCwa95241 and CSCwb14844.

December 7, 2021

In the Compatibility Information section, for the N9K-C9364C-GX switch, added:

All 4 fans must be operational, otherwise the switch will power down due to a fan policy trigger.

November 15, 2021

In the Open Issues section, added bug CSCvy69104.

August 18, 2021

In the Compatibility Information section, for the N9K-C9316D-GX, N9K-C93600CD-GX, and N9K-C9364C-GX switches, added:

1G and 100MB speeds are not supported.

August 10, 2021

In the Open Issues section, added bugs CSCvy30381, CSCvq57414, CSCvx76219, and CSCvy43728.

July 29, 2021

In the Modular Spine Switch Fabric Modules table, for N9K-C9504-FM, N9K-C9508-FM, and N9K-C9516-FM, changed the maximum to 6.

July 6, 2021

In the Supported Hardware section, added the NXA-PAC-500W-PI and NXA-PAC-500W-PE PSUs.

June 24, 2021

In the Open Issues section, added bug CSCvu07844.

June 21, 2021

Added known issue CSCvu42069.

June 15, 2021

In the Open Issues section, added bug CSCvy43640.

May 17, 2021

In the Open Issues section, added bug CSCvq57414.

February 22, 2021

In the Open Issues section, added bug CSCvx18314.

January 22, 2021

In the Open Issues section, added bug CSCvt73069.

January 19, 2021

In the Known Issues section, changed the following sentence:

The Cisco Nexus 9508 ACI-mode switch supports warm (stateless) standby where the state is not synched between the active and the standby supervisor modules.

To:

The modular chassis Cisco ACI spine nodes, such as the Cisco Nexus 9508, support warm (stateless) standby where the state is not synched between the active and the standby supervisor modules.

March 26, 2020

Release 14.2(3q) became available. Added the open and resolved issues for this release.

March 13, 2020

In the Resolved Issues section, added bug CSCvr98827.

In the Known Issues section, added bug CSCvq56811.

January 24, 2020

Release 14.2(3n) became available. Added the resolved issues for this release.

December 20, 2019

Release 14.2(3l) became available. Added support for the Cisco Nexus 9364C-GX switch.

December 9, 2019

Release 14.2(3j) became available.

N9K-C9504

Cisco Nexus 9504 switch chassis

N9K-C9508

Cisco Nexus 9508 switch chassis

N9K-C9508-B1

Cisco Nexus 9508 chassis bundle with 1 supervisor module, 3 power supplies, 2 system controllers, 3 fan trays, and 3 fabric modules

N9K-C9508-B2

Cisco Nexus 9508 chassis bundle with 1 supervisor module, 3 power supplies, 2 system controllers, 3 fan trays, and 6 fabric modules

N9K-C9516

Cisco Nexus 9516 switch chassis

N9K-X9736C-FX

Cisco Nexus 9500 36-port 40/100 Gigabit Ethernet Cloud Scale line card

4

8

16

N9K-X9736Q-FX

Cisco Nexus 9500 36-port 40 Gigabit Ethernet Cloud Scale line card

4

8

16

N9K-X9732C-EX

Cisco Nexus 9500 32-port, 40/100 Gigabit Ethernet Cloud Scale line card

Note: The N9K-X9732C-EX line card cannot be used when a fabric module is installed in FM slot 25.

4

8

16

N9K-X9736PQ

Cisco Nexus 9500 36-port 40 Gigabit Ethernet line card

4

8

16

N9K-C9504-FM-E

Cisco Nexus 9504 cloud scale fabric module

4

5

N9K-C9508-FM-E

Cisco Nexus 9508 cloud scale fabric module

4

5

N9K-C9508-FM-E2

Cisco Nexus 9508 cloud scale fabric module

4

5

N9K-C9516-FM-E2

Cisco Nexus 9516 cloud scale fabric module

4

5

N9K-C9504-FM

Cisco Nexus 9504 classic fabric module

3

6

N9K-C9508-FM

Cisco Nexus 9508 classic fabric module

3

6

N9K-C9516-FM

Cisco Nexus 9516 classic fabric module

3

6

N9K-SUP-A+

Cisco Nexus 9500 Series supervisor module

N9K-SUP-B+

Cisco Nexus 9500 Series supervisor module

N9K-SUP-A

Cisco Nexus 9500 Series supervisor module

N9K-SUP-B

Cisco Nexus 9500 Series supervisor module

N9K-SC-A

Cisco Nexus 9500 Series system controller

N9K-C9316D-GX

Cisco Nexus 9300 platform switch with 16 10/40/100/400-Gigabit QSFP-DD ports (ports 1-16).

N9K-C9332C

Cisco Nexus 9300 platform switch with 32 40/100-Gigabit QSFP28 ports and 2 SFP ports. Ports 25-32 offer hardware support for MACsec encryption.

N9K-C9336PQ

Cisco Nexus 9336PQ switch, 36-port 40 Gigabit Ethernet QSFP

N9K-C9364C

Cisco Nexus 9300 platform switch with 64 40/100-Gigabit QSFP28 ports and two 1/10-Gigabit SFP+ ports. The last 16 of the QSFP28 ports are colored green to indicate that they support wire-rate MACsec encryption.

N9K-PAC-1200W

1200W AC power supply, port side intake pluggable

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches

N9K-PAC-1200W-B

1200W AC power supply, port side exhaust pluggable

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches

NXA-PAC-1200W-PE

1200W AC power supply, port side exhaust pluggable, with higher fan speeds for NEBS compliance

NXA-PAC-1200W-PI

1200W AC power supply, port side intake pluggable, with higher fan speeds for NEBS compliance

NXA-PAC-1100W-PE2

1100W AC power supply, port side exhaust pluggable

NXA-PAC-1100W-PI2

1100W AC power supply, port side intake pluggable

NXA-PAC-750W-PE

750W AC power supply, port side exhaust pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only on release 14.2(1) and later.

NXA-PAC-750W-PI

750W AC power supply, port side intake pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only on release 14.2(1) and later.

NXA-PDC-1100W-PE

1100W AC power supply, port side exhaust pluggable

NXA-PDC-1100W-PI

1100W AC power supply, port side intake pluggable

NXA-PDC-930W-PE

930W AC power supply, port side exhaust pluggable

NXA-PDC-930W-PI

930W AC power supply, port side intake pluggable

NXA-PHV-1100W-PE

1100W HVAC/HVDC power supply, port-side exhaust

NXA-PHV-1100W-PI

1100W HVAC/HVDC power supply, port-side intake

N9K-PUV-1200W

1200W HVAC/HVDC dual-direction airflow power supply

N9K-C9300-FAN3

Burgundy port side intake fan

N9K-C9300-FAN3-B

Blue port side exhaust fan

N9K-C9504-FAN

Fan tray for Cisco Nexus 9504 chassis

N9K-C9508-FAN

Fan tray for Cisco Nexus 9508 chassis

N9K-C9516-FAN

Fan tray for Cisco Nexus 9516 chassis

NXA-FAN-160CFM-PE

Blue port side exhaust fan

NXA-FAN-160CFM-PI

Burgundy port side intake fan

NXA-FAN-35CFM-PE

Blue port side exhaust fan

NXA-FAN-35CFM-PI

Burgundy port side intake fan

N9K-C9364C-GX

Cisco Nexus 9300 platform switch with 64 100-Gigabit Ethernet QSFP28 ports, two management ports (one RJ-45 port and one SFP port), one console port (RS-232), and 1 USB port.

N9K-C93600CD-GX

Cisco Nexus 93600CD-GX switch with 28 10/40/100-Gigabit Ethernet QSFP28 ports (ports 1-28) and 8 10/40/100/400-Gigabit QSFP-DD ports (ports 29-36).

N9K-C93240YC-FX2

Cisco Nexus 9300 platform switch with 48 1/10/25-Gigabit Ethernet SFP28 ports and 12 40/100-Gigabit Ethernet QSFP28 ports. The N9K-C93240YC-FX2 is a 1.2-RU switch.

Note: 10/25G-LR-S with QSA is not supported.

N9K-C93216TC-FX2

Cisco Nexus 9300 platform switch with 96 1/10GBASE-T (copper) front panel ports and 12 40 /100-Gigabit Ethernet QSFP28 spine-facing ports

N9K-C93360YC-FX2

Cisco Nexus 9300 platform switch with 96 1/10/25-Gigabit front panel ports and 12 40 /100-Gigabit Ethernet QSFP spine-facing ports.

Note: The supported total number of fabric ports and port profile converted fabric links is 64.

N9K-C9336C-FX2

Cisco Nexus 9336C-FX2 Top-of-rack (ToR) switch with 36 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports.

Note: 1-Gigabit QSA is not supported on ports 1/1-6 and 1/33-36. The port profile feature supports downlink conversion of ports 31 through 34. Ports 35 and 36 can only be used as uplinks.

N9K-C93108TC-FX

Cisco Nexus 9300 platform switch with 48 1/10GBASE-T (copper) front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports.

Note: Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

N9K-C93108TC-FX-24

Cisco Nexus 9300 platform switch with 24 1/10GBASE-T (copper) front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports.

Note: Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

N9K-C93180YC-FX

Cisco Nexus 9300 platform switch with 48 1/10/25-Gigabit Ethernet SFP28 front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports. The SFP28 ports support 1-, 10-, and 25-Gigabit Ethernet connections and 8-, 16-, and 32-Gigabit Fibre Channel connections.

Note: Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

N9K-C93180YC-FX-24

Cisco Nexus 9300 platform switch with 24 1/10/25-Gigabit Ethernet SFP28 front panel ports and 6 fixed 40/100-Gigabit Ethernet QSFP28 spine-facing ports. The SFP28 ports support 1-, 10-, and 25-Gigabit Ethernet connections and 8-, 16-, and 32-Gigabit Fibre Channel connections.

Note: Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

N9K-C9348GC-FXP

Cisco Nexus 9348GC-FXP switch with 48 100/1000-Megabit 1GBASE-T downlink ports, 4 10-/25-Gigabit SFP28 downlink ports, and 2 40-/100-Gigabit QSFP28 uplink ports.

N9K-C93108TC-EX

Cisco Nexus 9300 platform switch with 48 1/10GBASE-T (copper) front panel ports and 6 40/100-Gigabit QSFP28 spine facing ports.

N9K-C93108TC-EX-24

Cisco Nexus 9300 platform switch with 24 1/10GBASE-T (copper) front panel ports and 6 40/100-Gigabit QSFP28 spine facing ports.

N9K-C93180LC-EX

Cisco Nexus 9300 platform switch with 24 40-Gigabit front panel ports and 6 40/100-Gigabit QSFP28 spine-facing ports.

The switch can be used as either a 24 40G port switch or a 12 100G port switch. If 100G is connected the Port1, Port 2 will be HW disabled.

N9K-C93180YC-EX

Cisco Nexus 9300 platform switch with 48 1/10/25-Gigabit front panel ports and 6-port 40/100 Gigabit QSFP28 spine-facing ports.

N9K-C93180YC-EX-24

Cisco Nexus 9300 platform switch with 24 1/10/25-Gigabit front panel ports and 6-port 40/100 Gigabit QSFP28 spine-facing ports.

N9K-C9372PX-E

Cisco Nexus 9372PX-E Top-of-rack (ToR) Layer 3 switch with 48 Port 1/10-Gigabit APIC-facing ports Ethernet SFP+ front panel ports and 6 40-Gbps Ethernet QSFP+ spine-facing ports

Note: Only the downlink ports 1-16 and 33-48 are capable of supporting SFP1-10G-ZR SFP+.

N9K-C9372TX-E

Cisco Nexus 9372TX-E Top-of-rack (ToR) Layer 3 switch with 48 10GBASE-T (copper) front panel ports and 6 40-Gbps Ethernet QSFP+ spine-facing ports

N9K-C93120TX

Cisco Nexus 9300 platform switch with 96 1/10GBASE-T (copper) front panel ports and 6-port 40-Gigabit Ethernet QSFP spine-facing ports.

N9K-C93128TX

Cisco Nexus 9300 platform switch with 96 1/10GBASE-T (copper) front panel ports and 6 or 8 40-Gigabit Ethernet QSFP spine-facing ports.

N9K-C9332PQ

Cisco Nexus 9332PQ Top-of-rack (ToR) Layer 3 switch with 26 APIC-facing ports and 6 fixed-Gigabit spine facing ports.

N9K-C9372PX

Cisco Nexus 9372PX Top-of-rack (ToR) Layer 3 switch with 48 Port 1/10-Gigabit APIC-facing ports Ethernet SFP+ front panel ports and 6 40-Gbps Ethernet QSFP+ spine-facing ports

Note: Only the downlink ports 1-16 and 33-48 are capable of supporting SFP1-10G-ZR SFP+.

N9K-C9372TX

Cisco Nexus 9372TX Top-of-rack (ToR) Layer 3 switch with 48 1/10GBASE-T (copper) front panel ports and 6 40-Gbps Ethernet QSFP spine-facing ports

N9K-C9396PX

Cisco Nexus 9300 platform switch with 48 1/10-Gigabit SFP+ front panel ports and 6 or 12 40-Gigabit Ethernet QSFP spine-facing ports  

N9K-C9396TX

Cisco Nexus 9300 platform switch with 48 1/10GBASE-T (copper) front panel ports and 6 or 12 40-Gigabit Ethernet QSFP spine-facing ports

N9K-M12PQ

12-port or 8-port Gigabit Ethernet expansion module

N9K-M6PQ

6-port Gigabit Ethernet expansion module

N9K-M6PQ-E

6-port, 40 Gigabit Ethernet expansion module

NXA-PAC-2KW-PE

Nexus 9000 2KW AC power supply, port-side exhaust

Note: This power supply is supported only by the Cisco Nexus 9364C-GX ACI-mode switch.

NXA-PAC-2KW-PI

Nexus 9000 2KW AC power supply, port-side intake

Note: This power supply is supported only by the Cisco Nexus 9364C-GX ACI-mode switch.

N9K-PAC-1200W

1200W AC power supply, port side intake pluggable

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches

N9K-PAC-1200W-B

1200W AC power supply, port side exhaust pluggable

Note: This power supply is supported only by the Cisco Nexus 93120TX, 93128TX, and 9336PQ ACI-mode switches

N9k-PAC-3000W-B

3000W AC power supply, port side intake

N9K-PAC-650W

650W AC power supply, port side intake pluggable

N9K-PAC-650W-B

650W AC power supply, port side exhaust pluggable

NXA-PAC-1200W-PE

1200W AC power supply, port side exhaust pluggable, with higher fan speeds for NEBS compliance

NXA-PAC-1200W-PI

1200W AC power supply, port side intake pluggable, with higher fan speeds for NEBS compliance

NXA-PAC-1100W-PE2

1100W AC power supply, port side exhaust pluggable

NXA-PAC-1100W-PI2

1100W AC power supply, port side intake pluggable

NXA-PAC-750W-PE

750W AC power supply, port side exhaust pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only on release 14.2(1) and later.

NXA-PAC-750W-PI

750W AC power supply, port side intake pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only on release 14.2(1) and later.

NXA-PAC-650W-PE

650W AC power supply, port side exhaust pluggable

NXA-PAC-650W-PI

650W AC power supply, port side intake pluggable

NXA-PAC-500W-PE

500W AC Power supply, port side exhaust pluggable

NXA-PAC-500W-PI

500W AC Power supply, port side intake pluggable

NXA-PAC-350W-PE

350W AC power supply, port side exhaust pluggable

NXA-PAC-350W-PI

350W AC power supply, port side intake pluggable

NXA-PDC-2KW-PE

Nexus 9000 2KW DC power supply, port-side exhaust

Note: This power supply is supported only by the Cisco Nexus 9364C-GX ACI-mode switch.

NXA-PDC-2KW-PI

Nexus 9000 2KW DC power supply, port-side intake

Note: This power supply is supported only by the Cisco Nexus 9364C-GX ACI-mode switch.

NXA-PDC-1100W-PE

1100W AC power supply, port side exhaust pluggable

NXA-PDC-1100W-PI

1100W AC power supply, port side intake pluggable

NXA-PDC-930W-PE

930W AC power supply, port side exhaust pluggable

NXA-PDC-930W-PI

930W AC power supply, port side intake pluggable

NXA-PDC-440W-PE

440W DC power supply, port side exhaust pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only by the Cisco Nexus 9348GC-FXP ACI-mode switch.

NXA-PDC-440W-PI

440W DC power supply, port side intake pluggable, with higher fan speeds for NEBS compliance

Note: This power supply is supported only by the Cisco Nexus 9348GC-FXP ACI-mode switch.

NXA-PHV-2KW-PE

Nexus 9000 2KW AC power supply, port-side exhaust

Note: This power supply is supported only by the Cisco Nexus 9364C-GX ACI-mode switch.

NXA-PHV-2KW-PI

Nexus 9000 2KW AC power supply, port-side intake

Note: This power supply is supported only by the Cisco Nexus 9364C-GX ACI-mode switch.

NXA-PHV-1100W-PE

1100W HVAC/HVDC power supply, port-side exhaust

NXA-PHV-1100W-PI

1100W HVAC/HVDC power supply, port-side intake

NXA-PHV-350W-PE

350W HVAC/HVDC power supply, port-side exhaust

NXA-PHV-350W-PI

350W HVAC/HVDC power supply, port-side intake

N9K-PUV-1200W

1200W HVAC/HVDC dual-direction airflow power supply

N9K-PUV-3000W-B

3000W AC power supply, port side exhaust pluggable

UCSC-PSU-930WDC V01

Port side exhaust DC power supply compatible with all ToR leaf switches

UCS-PSU-6332-DC

930W DC power supply, reversed airflow (port side exhaust)

N9K-C9300-FAN2

Burgundy port side intake fan

N9K-C9300-FAN2-B

Blue port side exhaust fan

N9K-C9300-FAN3

Burgundy port side intake fan

N9K-C9300-FAN3-B

Blue port side exhaust fan

NXA-FAN-160CFM2-PE

Blue port side exhaust fan

NXA-FAN-160CFM2-PI

Burgundy port side intake fan

NXA-FAN-160CFM-PE

Blue port side exhaust fan

NXA-FAN-160CFM-PI

Burgundy port side intake fan

NXA-FAN-30CFM-B

Burgundy port side intake fan

NXA-FAN-30CFM-F

Blue port side exhaust fan

NXA-FAN-35CFM-PE

Blue port side exhaust fan

NXA-FAN-35CFM-PI

Burgundy port side intake fan

NXA-FAN-65CFM-PE

Blue port side exhaust fan

NXA-SFAN-65CFM-PE

Blue port side exhaust fan

NXA-FAN-65CFM-PI

Burgundy port side intake fan

NXA-SFAN-65CFM-PI

Burgundy port side intake fan

CSCvt67249

After upgrading to release 4.2(3q), Fibre Channel interfaces go down with faults F3248 and F3307.

14.2(3q) and later

CSCvt94412

In a situation in which a virtual machine cannot reach the default gateway, Cisco ACI declares a VMNIC as down, but VMware vCenter displays that VMNIC as connected.

14.2(3q) and later

CSCvu51926

ARP packets are dropped in the fabric that should be implicitly permitted using zoning-rule programming. The packet drop reason is SECURITY_GROUP_DENY and the specific rule is implicit deny for the VRF table.

14.2(3q) and later

CSCvu77758

The import BGP route target that should allow leaf switches to import L3Out routes from another site is missing. As a result, the leaf switches with the missing route targets will not be able to learn routes from the remote site L3Out.

14.2(3q) and later

CSCvv00866

The FCOE host may experience latency and disconnections after a fabric monitoring policy change for the switch nodes. The monitor policy itself does not include an FCOE setting. However, the policy change may result in impact to FCOE traffic on the switch level.

14.2(3q) and later

CSCvv15984

vPC switches crash due to a vPC HAP reset and a vPC HAP reset core is generated.

14.2(3q) and later

CSCvv20545

DHCP generates a core file due to a memory leak issue. If you have a remote leaf switch and DHCP configured, you can run into this issue.

14.2(3q) and later

CSCvv37217

A /32 host-based route is not advertised out of an L3Out when there is endpoint instability in the network for the specific host.

14.2(3q) and later

CSCvv43137

The Cisco ACI fabric raises the critical event E4208052 "Operation errors internal error in BGP instance"."Inconsistent flags" messages are logged in "show bgp internal event-history logs".

14.2(3q) and later

CSCvv89037

The kernel hits a HAP reset or generates a core.

14.2(3q) and later

CSCvy43728

After downgrading a Cisco ACI leaf or spine switch from a 4.2 release to a 3.2 release, you may notice that the switch becomes "active" in the fabric (acidiag fnvread), but the node is missing many policies allowing it to function properly, such as the BGP Route Reflector policies.

14.2(3q) and later

CSCvu28036

There is traffic loss as a result of a missing endpoint in COOP on the spine node.

14.2(3n) and later

CSCvu30087

After reloading, clean reloading, or upgrading, a remote leaf node, the remote leaf node L3Outs no longer advertise host routes.

14.2(3n) and later

CSCvw27406

There is a discrepancy in the "show ip pim group-range vrf all" in iBash and VSH mode.

14.2(3n) and later

CSCwb14844

There is a long delay when connecting a Cisco N9K-C9336C-FX2 switch to a Mellanox NIC/40G using QSFP-40G-SR4. The status of the port is down, not connected.

14.2(3n) and later

CSCvs78260

After deleting and reconfiguring routable subnets, a spine switch will not have NAT entries retriggered. The NAT entries will be empty even though the routable IP addresses are populated in uRIB.

14.2(3l) and later

CSCvs84712

After upgrading from a 14.2 release to a later 14.2 release, the remote leaf switch was inactive. The spine switch appeared to be doing the correct NAT for the routable IP addresses, but there were no routes back to the APIC 2 and 3 in overlay-1 uRIB. Only APIC 1 was reachable, as it had the route populated in the uRIB through ISIS (originated from the leaf switch connected to APIC 1).

14.2(3l) and later

CSCvs96658

SSH from external devices connected over L3Out does not successfully reach the in-band management IP address of the spine and leaf switches. From outside of the fabric, all in-band management devices are reachable through ping. From outside of the fabric, ssh to Cisco APIC works.

14.2(3l) and later

CSCvs97879

According to the documentation, power supply slot 1 is on the left and slot 2 is on the right. However, N9K-C9332C recognizes the left side slot as slot 2 and vice versa.

14.2(3l) and later

CSCvt41414

When a Layer 4 to Layer 7 vIP address move is triggered across PODs, the leaf switch does not update a local learn to a cached state.

14.2(3l) and later

CSCvt63819

A border leaf switch reflects a certain number of EIGRP routes received from the external router. This issue is seen after a batch of routes are withdrawn downstream of the external router.

14.2(3l) and later

CSCvt69356

The sysmgr process generates core files from time to time on spine switches.

14.2(3l) and later

CSCvt85499

When using host-based routing (/32 host route for an endpoint advertised to an L3Out) and the border leaf node loses all of its adjacency, the border leaf node keeps the /32 host route and still advertises the route to the routing protocol for about 15 minutes. This can cause a blackhole of traffic from external routes to the /32 host routes.

14.2(3l) and later

CSCvu14545

An admin down or blacklisted port shows as being delivered power with the command "show power inline".

14.2(3l) and later

CSCvu16473

While enabling remote leaf direct forwarding for an existing remote leaf vPC pair, connectivity loss is seen when communicating from the pod that the remote leaf is not a part of to the bridge domain pervasive gateway on the remote leaf pair. Specifically, the issue is seen after the first vPC member is decommissioned and brought back into the fabric and after the second leaf switch is decommissioned and reloaded, and before the second leaf switch is brought back into the fabric. This only affects reachability to the pervasive gateway on the remote leaf from sources in the pod of which the remote leaf is not a part.

14.2(3l) and later

CSCvu23722

Removing GBIC from leaf node uplink ports/spine node ports generates the "Transceiver has been removed" syslog event on unused ports on the spine node and some leaf nodes.

The reason is that when GBIC is removed, it triggers these events internally due to using the wrong ethpmFcot managed object logic. The only affect the internal managed object class update behavior. You can safely ignore the events.

14.2(3l) and later

CSCvu47561

The remote site VRF SVI IP address is missing in COOP.

14.2(3l) and later

CSCvu76867

Continuously deleting and re-adding service graph contract filters can result in leaf switches crash due to policy_mgr hap reset:

          Reason: Reset triggered due to HA policy of Reset

          System version: 14.2(3l)

          Service: policy_mgr hap reset

14.2(3l) and later

CSCvu82481

There is a memory leak on the leaf switches due to the vlan_mgr process.

14.2(3l) and later

CSCvu97674

For all Avago 100/25G links, link up delay may be observed.

14.2(3l) and later

CSCvv09950

Under "show platform internal counters port internal detail" of a Cisco N9K-C9504-FM-E switch, a lot of values seem to be stuck at 4294967295. This issue is cosmetic. There is no impact to traffic.

14.2(3l) and later

CSCvv61715

A system's 100G/25G link can take up to 3 minutes to link up.

14.2(3l) and later

CSCvv92044

Frequent link flaps are seen on a spine switch that is using the QSFP-100G-SM-SR transceiver.

14.2(3l) and later

CSCvs29384

Fault F3525 (high SSD usage) is observed.

14.2(3j) through 14.2(3n)

CSCvt00457

Egress FCOE traffic is incorrectly classified in the default class (Level 3) instead of the no drop class (Level 1).  This issue causes priority flow control to not transmit pause frames to throttle the traffic during heavy congestion.  Level1 Rx Drop Pkts/Bytes will then result.

14.2(3j) through 14.2(3n)

CSCvg85886

When an ARP request is generated from one endpoint to another endpoint in an isolated EPG, an ARP glean request is generated for the first endpoint.

14.2(3j) and later

CSCvh11299

In COOP, the MAC IP address route has the wrong VNID, and endpoints are missing from the IP address DB of COOP.

14.2(3j) and later

CSCvh18100

If Cisco ACI Virtual Edge or AVS is operating in VxLAN non-switching mode behind a FEX, the traffic between endpoints in the same EPG will fail when the bridge domain has ARP flooding enabled.

14.2(3j) and later

CSCvo39715

When downgrading a Cisco ACI fabric, the OSPF neighbors go down after downgrading the Cisco APICs from a 3.2 or later release to a pre-3.2 release. After the upgrade, the switches are still running a 13.2 or later release.

14.2(3j) and later

CSCvp09949

Copy service traffic will fail to reach the TEP where the copy devices are connected. Traffic will not be seen on the spine switches.

14.2(3j) and later

CSCvp50075

A leaf switch experiences an unexpected reload due to a HAP reset.

14.2(3j) and later

CSCvp72312

A contract that is provided by an EPG using a bridge domain with subnet X and that is consumed by an L3Out EPG causes a leak of subnet X from VRF B to VRF A. The existing non-pervasive static route in VRF A is replaced by a pervasive route in pointing to spine switch V4 proxy. After the contract leaking subnet A is removed, the pervasive static route persists.

14.2(3j) and later

CSCvq19269

When a vPC leg goes down and comes back up, a long traffic drop (1-2 minutes) may occur.

14.2(3j) and later

CSCvq19279

BFD sessions keep flapping between a -GX leaf and spine switches. The command "show system internal bfd event-history session" shows multiple instances of the Echo function failing:
"Session state changed: 3(Up) -> 1(Down), New diag: 2(Echo Function Failed)"

14.2(3j) and later

CSCvq57414

HSRP/VRRP packets failed to flood locally in a service leaf switch, which causes a dual active state.

14.2(3j) and later

CSCvr02421

N2348TQ tiburon fex randomly reboots. Crash in the 'tiburon' and/or 'ethpc' service may be observed in syslogs immediately prior to reload event.

14.2(3j) and later

CSCvr16588

In a GOLF setup on a spine switch, when the bridge domain subnets and endpoints are associated to a newer VRF table and the older VRF table is deleted, after changing the VRF table (detaching the old VRF table and attaching a new VRF table) it takes long time (approximately 30 minutes) for host routes of endpoints to be advertised to CSR GOLF.

14.2(3j) and later

CSCvr76947

After upgrading leaf switches and after the switches come online on the target firmware version, reloading the chassis causes a failure to boot and a crash to the Loader> prompt with nothing left in the bootflash from which to boot.

14.2(3j) and later

CSCvr79911

An LLDP/CDP MAC address entry gets stuck in the blade switch table on a leaf switch in a vPC. The entry can get stuck if the MAC address flaps and hits the move detection interval, which stops all learning for the address.  Use the following command to verify if a switch has a stale MAC address entry:

module-1# show system internal epmc bladeswitch_mac all

14.2(3j) and later

CSCvr83337

A Cisco ACI leaf switch unexpectedly reloads and generates a core file.

14.2(3j) and later

CSCvr91674

Whenever a switch hits a burst of PCIe, DRAM, or MCE errors, sometimes the device_test process crashes, which can cause the switch to reload.

14.2(3j) and later

CSCvs06119

Multiple switches crash and generate a core file at same time when applying an NTP policy.

14.2(3j) and later

CSCvs14405

During a shared service scenario with an EPG and L3Out, if the same route is under both the EPG and L3Out, the route is leaked and the ctrl property of the route is set to pervasive. If the contract is later removed, the pervasive flag on the leaked route is not cleaned up.

14.2(3j) and later

CSCvs18150

After a certain set of steps, it is observed that the deny-external-tag route-map used for transit routing loop prevention gets set back to the default tag 4294967295. Since routes arriving in Cisco ACI with this tag are denied from being installed in the routing table, if the VRF table that has the route-tag policy is providing transit for another VRF table in Cisco ACI (for instance and inside and outside vrf with a fw connecting them) and the non-transit VRF table has the default route-tag policy, routes from the non-transit VRF table would not be installed in the transit VRF table.

This bug is also particularly impactful in scenarios where transit routing is being used and OSPF or EIGRP is used on a vPC border leaf switch pair. vPC border leaf switches peer with each other, so if member A gets a transit route from BGP, redistributes into OSPF, and then advertises to member B (since they are peers)...without a loop prevention mechanism, member B would install the route through OSPF since it has a better admin distance and would then advertise back into BGP. This VRF tag is set on redistribution of BGP > OSPF and then as a table map in OSPF that blocks routes with the tag from getting installed in the routing table. When hitting this bug, the route-map used for redistributing into OSPF still sets the tag to the correct value. However, the table map no longer matches the correct tag. Rather, it matches the default tag. As a result, member A (could be B) would install the route through OSPF pointing to B. It would then redistribute it back into BGP with the med set to 1. The rest of the fabric (including member B) would install the BGP route pointing to member A since its med is better than the original route's med.

14.2(3j) and later

CSCvs21844

A data packet in a Layer 2-only VLAN dedicated for an FTD cluster communication link (CCL) has an invalid L4 checksum (expected). An N9K-C9364C switch seems to be stomping these packets when getting them from the IPN on interfaces 65-66. This results in an incorrect l2 frame checksum, and a data packet from FTD-A sent to FTD-B through Cisco ACI cannot be processed.

14.2(3j) and later

CSCvs31340

In ACI 4.1 releases, FEX port-channel member interfaces (NIF) can no longer be configured as SPAN source interfaces.

The following Fault is raised and the SPAN session remains operationally down:

F1199: Span source interface sys/phys-[eth1/x] on node xxx in failed state reason Configuration not supported on this TOR.

14.2(3j) and later

CSCvs34065

The "get_bkout_cfg failed" error displays when the following vsh_lc cli command is executed:

vsh_lc -c "show system internal port-client event-history all"

14.2(3j) and later

CSCvs40299

The policy_mgr process on an ACI leaf switch has a memory leak and results in an unexpected reload.

The problem can happen over a long period of time, such as a year. Depending on when individual switches were last rebooted, multiple devices could experience the reload at around the same time.

14.2(3j) and later

CSCvs40360

Filing an enhancement to add SNMPv3 support for using AES-256 encryption.

14.2(3j) and later

CSCvs41818

Port 1/2 on N9k-C9364C flaps continuously and does not come up.

14.2(3j) and later

CSCvs45414

A N9K-X9736PQ linecard in an ACI mode Nexus 9500 spine switch unexpectedly reloads. The following output is seen in the command "show system reset-reason module 1":

    `show system reset-reason module 1`

    *************** module reset reason (1) *************

    0) At 2019-12-01T00:00:00.00

        Reason: line-card-not-responding

        Service:Line card not responding => [Failures < MAX] : powercycle

        Version:

14.2(3j) and later

CSCvs49377

After a virtual machine is vMotioned, traffic begins to drop the source from that endpoint. When running "show logging ip access-list internal packet-log deny" on the leaf switch, you can see policy drops for the endpoint.

14.2(3j) and later

CSCvs50080

When fast-link failover hardware support is enabled with more than 32 fabric ports, the sdkhal process aborts.

14.2(3j) and later

CSCvs56556

A local AS configuration is not applied to the eBGP neighbor on a Cisco ACI border leaf switch, which results in the switch sending the fabric ASN (configured in the BGP Route Reflector policy) in the OPEN messages, which makes the neighbor reject the session because of the "bad remote-as" reason.

14.2(3j) and later

CSCvs56978

Connectivity between a server EPG and external L3Out EPG can be broken for some subnets that are configured with an external subnet for an external EPG.

14.2(3j) and later

CSCvs57186

After a link to a Cisco ACI leaf switch flaps, ARP continuously refreshes, and unicast traffic to a neighboring device is non-functional. In a packet capture, the leaf switch continuously sends ARP requests for the neighboring device, even though that device is sending ARP responses. When running "show ip arp vrf tenant:vrf", the age of the ARP entry is always 0 seconds.

14.2(3j) and later

CSCvs60566

A vPC pair of leaf switches go into the split brain mode, causing traffic duplication.

14.2(3j) and later

CSCvs61270

A modular spine switch gets stuck during upgrade.

14.2(3j) and later

CSCvs66240

During leaf switch replacement, vPC ports (map-pinning mode) are flapped on existing switches in the vPC pair.

14.2(3j) and later

CSCvs76848

A switch SSD fails in less than two years and needs replacement. The /mnt/pss/ssd_log_amp.log file shows daily P/E cycles increasing by 10 or more each day, and fault "F3525: High SSD usage" is observed. Check the switch activity and contact Cisco Technical Support if the "High SSD usage" fault is raised on the switch.

14.2(3j) and later

CSCvs77436

Error message "No handlers could be found for logger "root"" appears when doing a moquery for certain objects.

14.2(3j) and later

CSCvs77484

A spine switch fabric module or line card is reloaded unexpectedly due to a kernel panic. The stack trace includes the following statement:
Kernel panic - not syncing: Out of memory: system-wide panic_on_oom is enabled.

14.2(3j) and later

CSCvs79018

Running log_trace_bl_print_tool will result in the decoded binary logs referencing the system localtime. This will likely differ from the timezone of the collected techsupports.

14.2(3j) and later

CSCvs83366

The COPP per interface policy feature has following limitation:

The TCAM entry maximum for per interface per protocol is 256. After the threshold is exceeded, a fault will be raised. For more information, see:

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/4-x/security/b-Cisco-APIC-Security-Configuration-Guide-411/b-Cisco-APIC-Security-Configuration-Guide-411_chapter_01001.html

This enhancement request is to have a CLI command to display the number of  required ACLs/TCAM entries for the COPP policy that is applied on a per-interface level. The command should possibly display whether the configuration will succeed or not based on the current overall TCAM usage.

14.2(3j) and later

CSCvs87079

The CL91-RS-FEC mode is rejected for 25G ports on certain platforms and F1186 is raised.

14.2(3j) and later

CSCvs89617

Some ARP packets get dropped across the Cisco ACI fabric.

14.2(3j) and later

CSCvs92068

After upgrading, leaf switch in-band management addresses cannot be accessed using SSH. Traffic is dropped by the iptables. This can be verified as root with the following commands:

iptables -N LOGGING

iptables -A INPUT -j LOGGING

iptables -A LOGGING -j LOG --log-prefix "IPTables-Dropped: " --log-level 4

iptables -A LOGGING -j DROP

dmesg -T | grep "Dropped"

14.2(3j) and later

CSCvs96869

A leaf switch will crash with a vntag_mgr HAP reset and generate a core file.

14.2(3j) and later

CSCvt00231

Traffic destined to a switch is policy dropped.  The contracts configured on the switch look correct, but the ELAM drop reason shows a clear SECURITY_GROUP_DENY. If you dump the FPC and FPB pt.index results of the ELAM, the values are different. Specifically, the FPC index is wrong when you check the Stats Idx under the specific ACLQOS rule. FPC should be the summary of the final result. In this case, there are two hits, but there is one stable entry in TCAM and one that is not stable.

14.2(3j) and later

CSCvt07621

The fabric module on a modular spine switch crashes with sdkhal-hap-reset and generates an sdkhal core file.

14.2(3j) and later

CSCvt08181

All routes to a particular spine switch are removed from uRIB on all leaf switches in the fabric.

14.2(3j) and later

CSCvt09775

The policy element crashes due to database space exhaustion with B22 FEX devices in the fabric.

14.2(3j) and later

CSCvt10439

Frames from IPN marked with COS 6 might get dropped by a spine switch.

14.2(3j) and later

CSCvt14717

Random flaps on individual breakout ports.

14.2(3j) and later

CSCvt18714

Known unicast packets with COS 6 from IPN might get dropped by the Cisco ACI fabric.

14.2(3j) and later

CSCvt25383

The pervasive static route is missing on the spine node.

14.2(3j) and later

CSCvt35002

A link intermittently flaps on leaf switch fabric ports that are connected to a spine switch.

14.2(3j) and later

CSCvt39689

Glean ARP (0xfff2, 239.255.255.240) flood is stopped on the transit leaf switch and is not delivered toward all the leaf switches in the fabric. Thus, silent host discovery does not work.

14.2(3j) and later

CSCvt44961

After an upgrade, some ports do not come up.

14.2(3j) and later

CSCvt52364

A leaf switch reloaded with an NFM process core.

14.2(3j) and later

CSCvt52620

There is a stale pervasive route after a DHCP relay label is deleted.

14.2(3j) and later

CSCvt57119

A Cisco ACI leaf switch sends traffic that is untagged for a particular VLAN even though it is configured as trunk (tagged).

14.2(3j) and later

CSCvt64042

The policy element crashes once during a misconfiguration.

14.2(3j) and later

CSCvt64733

An ARP request from the endpoint behind the remote leaf switch is received on the ToR switch and is flooded to the spine switch as expected (ARP flooding enabled on bridge domain). This can be an issue in cases where the endpoint is behind something such as a Fabric Interconnects, in which it may be expected behavior to delete the MAC address if the endpoint receives the same MAC address back from the upstream leaf switches.

14.2(3j) and later

CSCvt67458

Graceful restart does not show up in "show ip ospf" when enabled.

14.2(3j) and later

CSCvt72137

Traffic on the interface of leaf switch model N9K-C9348GC-FXP is being received at the rate of 125k pps and is not being dropped.

14.2(3j) and later

CSCvt73069

A Cisco ACI fabric is not fully fit after a Cisco APIC firmware upgrade.

14.2(3j) and later

CSCvt80543

The Cisco N9K-C9316D-GX spine switches encounter a SDKHAL process crash if the route hardware scale limits are exceeded.

14.2(3j) and later

CSCvt94039

A leaf switch crashes and reloads due to "nfm hap reset".

14.2(3j) and later

CSCvu01639

There are faults for failed contract rules and prefixes on switches prior to the -EX switches. Furthermore, traffic that is destined to an L3Out gets dropped because the compute leaf switches do not have the external prefix programmed in ns shim GST-TCAM. You might also see that leaf switches prior to the -EX switches do not have all contracts programmed correctly in the hardware.

14.2(3j) and later

CSCvu08065

If inter-VRF DHCP relay is used, it may be observed that DHCP breaks after performing any activity that causes the client VRF to get removed and re-deployed on the client leaf nodes.

14.2(3j) and later

CSCvu15712

If a spine switch's PTEP is configured as the multipod L3Out router ID and the router ID is later changed, the spine switch's PTEP loopback gets deleted and the MP BGP session goes down.

14.2(3j) and later

CSCvu15751

The following event can be seen on the spine node:

[E4204936][transition][warning][sys] %URIB-4-SYSLOG_SL_MSG_WARNING: URIB-5-RPATH_DELETE: message repeated 1 times in last 220162 sec

14.2(3j) and later

CSCvu16987

A Cisco ACI leaf switch reboots due to an ICMPv6 HAP reset.

14.2(3j) and later

CSCvu21147

QSFP-40G-SR-BD SFP shows DOM from "show interface ethernet x/x transceiver details" even though it is unsupported hardware.

14.2(3j) and later

CSCvu22736

There is an event in which the syslog message is masked and does not provide details about the issue. The main syslog message is not seen, but rate-throttled syslog messages are seen.

14.2(3j) and later

CSCvu26947

If a rogue file grows too large, it can cause out of memory condition on a spine switch or leaf switch line card or fabric module without proactively alerting the user to the memory leak, and the line card or fabric module will reload.

14.2(3j) and later

CSCvu27617

Fault F0098 gets raised and the statistics in the Capacity dashboards do not show for the affected leaf nodes.

14.2(3j) and later

CSCvu27791

Paths to L1/L2 devices do not get programmed although they are tracked as up. This happens in an active-standby deployment.

14.2(3j) and later

CSCvu32603

The AVAGO QSFP-100G-SR4 transceiver displays an abnormal Rx dbm value in a down port.

14.2(3j) and later

CSCvu40050

The spine node KIC database is missing the v4 default route from RIB. This causes in-band return traffic to drop on the way back to the border leaf nodes.

14.2(3j) and later

CSCvu48811

When a Cisco ACI switch is configured in a "maintenance mode" (mmode), a banner is displayed to the user indicating the operating mode of the switch.

14.2(3j) and later

CSCvu53558

When walking through SNMP targets, SNMP generates a core file on a spine switch.

14.2(3j) and later

CSCvu61024

Zoning-rules are not programmed in the hardware after reloading a switch.

14.2(3j) and later

CSCvu72416

Triggered by a physical layer issue, such as fiber or a bad transceiver, a link flap may happen every now and then. However, it is uncommon to have continuous flaps when the node is left unattended over an extended period, such as having 688,000 flaps over a year. Each time after the fabric link flaps, one dbgRemotePort managed object is added to the policyElement database. After a long time flapping like this, unexpected memory allocation and access can be triggered for the Nexus OS process, such as policy_mgr or ethpm.

This defect is to enhance the object-store to reduce the impact for such scenarios.

14.2(3j) and later

CSCvu84587

VTEP endpoints are learned and set to bounce on some leaf switches. A single VTEP IP address could be seen as local on one vPC pair, but as an IP XR with bounce on another leaf switch pair.

14.2(3j) and later

CSCvv01585

Pinging the inband-mgmt of a switch that is running in the ACI mode sometimes fails. This happens between leaf switches and also between leaf switches and spine switches.

14.2(3j) and later

CSCvv04251

A policy upgrade fails on the N9K-C9316D-GX and N9K-C93600CD-GX platforms that have the hw_changes_bit programmed as "0x03."

14.2(3j) and later

CSCvv08850

A fabric node device crashes with an SDKHAL core.

14.2(3j) and later

CSCvv13722

A leaf switch crashes due to a routing loop in the IPFIB process.

14.2(3j) and later

CSCvv17496

A FEX link takes a long time (5+ minutes) to come up.

14.2(3j) and later

CSCvv19805

The process could run out of memory if the port is flapped million times from the peer end.

14.2(3j) and later

CSCvv27817

DHCP unicast renewal ACKs are NOT forwarded across the fabric to clients. This traffic is sourced from port 67 destined to port 68. The regular Discover, Offer, Request, Acknowledge (DORA) process and unicast ACKs function correctly. This traffic is sourced from port 67 destined to port 67.
The DHCP renewals are incorrectly being punted to the CPU as ISTACK_SUP_CODE_DHCP_SNOOP on the ingress leaf switch.

14.2(3j) and later

CSCvv33100

The IPS port is not down when an RX cable is removed on a Cisco ACI leaf switch 1G port.

An ACI switch with 1G fiber would signal a peer IOS device, such as a Catalyst 6000 series switch, with flow control auto/desired to turn on the flow control.

14.2(3j) and later

CSCvv39277

After an upgrade, for one of the VRF tables, the BGP route map is missing on the spine switch, which results in bridge domain prefixes not being advertised.

14.2(3j) and later

CSCvv48587

Legitimate inter-pod glean traffic is dropped by the loop avoidance ACL on spine switches with or without Cisco ACI Multi-Pod QoS policies.

14.2(3j) and later

CSCvv75224

IPv6 BGP route with recursive next-hop is programmed in the software, but not programmed in the hardware. Traffic destined to this route is blackholed.

14.2(3j) and later

CSCvv78885

A stale route map entry is causes unexpected route leaking.

14.2(3j) and later

CSCvv92317

Egress buffer drops are seen on Cisco N9K-C9336C-FX2 or N9K-C93240YC-FX2 switches without congestion.

14.2(3j) and later

CSCvv95800

A spine switch reloads unexpectedly due to the service on the linecard having a hap-reset.

14.2(3j) and later

CSCvw07282

On a modular spine switch, an unconnected port's switching state is disabled, which means it is out of service. The issue is that after reloading a line card, all of the ports on that line card change to switching state enabled, even if the port is not connected to anything. This issue is mostly cosmetic; there is no real impact if an unconnected port has switching state enabled.

14.2(3j) and later

CSCvw16121

An IGMPv3 leave causes multicast route OIL to be deleted even when there is an existing receiver subscribed to the group. Multicast traffic interrupted until the existing receivers send a report in response to a general query.

14.2(3j) and later

CSCvw19911

After disabling unicast routing from a bridge domain, the static pervasive route is still present on the leaf switch.

14.2(3j) and later

CSCvx18314

DTEP between leaf switches fails to get established due to a rare timing condition. This results in XRs not being programmed between these leaf switches. If the XR was for a multicast source, then Layer 3 multicast from that source would get affected.

14.2(3j) and later

CSCvx76219

A tunnel connects to random IP addresses that do not exist in the ISIS table, which results in the following fault:F0475: Tunnel destination is not reachable

14.2(3j) and later

CSCvy30381

After replacing the hardware for a leaf switch, the leaf switch front-panel ports are set to the admin-down state for 45 minutes.

14.2(3j) and later

CSCvy43640

A leaf node crashes when PFC or LLFC is enabled on a stretched fabric or a Multi-tier fabric. PFC and LLFC is mainly used for FCoE and RoCE.

For a stretched fabric, when a transit leaf node that has connectivity to spine nodes in both locations receives the traffic that matches the QoS class with No-Drop-Cos and PFC enabled, the transit leaf node crashes.

For a Multi-tier fabric, when a tier-2 leaf node receives the traffic that matches the QoS class with No-Drop-Cos and PFC enabled, the tier-2 leaf node crashes.

14.2(3j) and later

CSCvy69104

If an endpoint exists as a dynamic endpoint and then gets configured as a Layer 4 to Layer 7 VIP address, EPM flushes the dynamic entry and waits for a new ARP to reprogram it as a static endpoint.The flush in EPM removes the entry in COOP, so endpoints communicating to the previous instance of the Layer 4 to Layer 7 VIP address could see a convergence issue until the next ARP is received.

14.2(3j) and later

CSCwa12763

External route import for a VRF instance fails on a leaf switch after removing a shared services contract between two EPGs.

14.2(3j) and later

CSCwa47686

For a Cisco ACI fabric with more than 128 leaf switches in a given pod, such as 210 leaf switches in a single pod deployment, after enabling PTP globally, only 128 leaf switches are able to enable PTP. The remaining 82 leaf switches fail to enable PTP due to the error F2728 latency-enable-failed.

14.2(3j) and later

CSCwa95241

An endpoint may fail to resolve an ARP request of another endpoint.

14.2(3j) and later

CSCwb08081

A route profile that matches on community list and sets the local pref and community is not working post upgrade to 5.2.x release.

route-map imp-l3out-L3OUT_WAN-peer-2359297, permit, sequence 4201

  Match clauses:

    community  (community-list filter): peer16389-2359297-exc-ext-in-L3OUT_WAN_COMMUNITY-rgcom

  Set clauses:

    local-preference 200

    community xxxxx:101 xxxxx:500 xxxxx:601 xxxxy:4 additive

The match clause works as expected, but the set clause is ignored.

14.2(3j) and later

CSCwb17229

The sysmgr process crashes unexpectedly, causing the line card to reload.

14.2(3j) and later

CSCwb39899

A Cisco ACI leaf switch will reload with the following reset reason:

Reset Reason for this card:

        Image Version : 14.2(7f)

        Reset Reason (LCM): Unknown (0) at time Tue Mar 22 13:01:28 2022

        Reset Reason (SW): Reset triggered due to HA policy of Reset (16) at time Tue Mar 22 12:56:21 2022

          Service (Additional Info): pim hap reset

        Reset Reason (HW): Reset triggered due to HA policy of Reset (16) at time Tue Mar 22 13:01:28 2022

        Reset Cause (HW): 0x01 at time Tue Mar 22 13:01:28 2022

        Reset internal (HW): 0x00 at time Tue Mar 22 13:01:28 2022

14.2(3j) and later

CSCwd29346

An ACI switch's console may continuously output messages similar to:

svc_ifc_eventmg (*****) Ran 7911 msecs in last 7924 msecs

14.2(3j) and later

CSCvs63794

There is a memory leak in EPM with IP endpoint moves. With continuous endpoint moves, the leak builds up and results in an EPM crash after approximately 37 days.

14.2(3j) and 14.2(3l)

CSCvr91980

In some circumstances, when the switch is in the loader> prompt, booting from USB fails.

14.2(3q)

CSCvs29384

Fault F3525 (high SSD usage) is observed.

14.2(3q)

CSCvt00457

Egress FCOE traffic is incorrectly classified in the default class (Level 3) instead of the no drop class (Level 1).  This issue causes priority flow control to not kick in to throttle the traffic during heavy congestion.

14.2(3q)

CSCvt24881

An ACI switch goes inactive in the fabric and the eventmgr crashes on the affected nodes.

14.2(3q)

CSCvs63794

There is a memory leak in EPM with IP endpoint moves. With continuous endpoint moves, the leak builds up and results in an EPM crash after approximately 37 days.

14.2(3n)

CSCvk73228

This is an enhancement to decode the binary logs offline directly from the techsupport.

14.2(3j)

CSCvn16192

CRC errors increment on a leaf switch front panel port, fabric ports, and spine switch ports in a fabric with switches whose model names end with -EX, -FX, or later.

14.2(3j)

CSCvo86795

SAN port channel bringup will be unsuccessful when a new vendor switch is connected and the Organizationally Unique Identifier (OUI) of the switch is not present in the OUI list.

14.2(3j)

CSCvp00694

If a tenant is undeployed from the Multi-Site Orchestrator, the limited VRF instances on the spine switch created for GOLF can be stuck in deletion based on timing. This issue occurs in a topology/ConfigA single pod setup, with a VRF instance and bridge domain that is stretched across sites and GOLF host route is enabled.

14.2(3j)

CSCvq28541

Ports with PoE auto mode enabled go into errdisable mode when a non-PoE-capable device is connected to the port.

14.2(3j)

CSCvq33855

The VMAC of an ACI SVI is used for an endpoint refresh instead of the PMAC. For example, it can cause an endpoint refresh issue, if the endpoint is reachable through OTV (when HSRP filtration is used and the HSRP MAC is set as a virtual MAC address).

14.2(3j)

CSCvq68352

A last hop router does not generate the S,G tree.

14.2(3j)

CSCvq87843

There is an RPF lookup failure for MRIB.

14.2(3j)

CSCvq98750

In Cisco ACI when using MAC pinning with a vPC, prior to reloading when you run the 'show vpc brief' command on the CLI, the command shows that the vPC is passing consistency checks. However, after reloading the leaf switch, the vPC then properly displays the consistency check as 'Not Applicable'.

14.2(3j)

CSCvr05132

Traffic drops occur if there is redirect traffic towards a remote leaf switch and a Layer 2 service device is deployed behind a remote leaf switch in RL Direct mode.

14.2(3j)

CSCvr09108

An interface does not come up when a new link is connected. However, from the DOM data, the signals are present.

14.2(3j)

CSCvr11460

In a source outside and receiver inside scenario, PIM on the NBL is computing the stripe winner, when there is local receiver. As a result of this, PIM sends out joins over the fabric. However, the route is not currently propagated to the other border leaf switches, which is the expected behavior.

14.2(3j)

CSCvr17706

There is a kernel-panic out of memory crash. The following logs appear in the kernel traces:

Kernel panic - not syncing: Out of memory: system-wide panic_on_oom is enabled

14.2(3j)

CSCvr27776

The sysmgr core got cleaned up as part of last core restore logic upon system reboot.

14.2(3j)

CSCvr31315

The SPAN manager process crashes when a SPAN session is deleted.

14.2(3j)

CSCvr31458

When a physical interface or transceiver is defective or has misconfigured speed, the fault displayed in the GUI has additional whitespaces.

14.2(3j)

CSCvr46681

Leaf switches crash and generate a core file after invoking the ACI snapshot rollback.

14.2(3j)

CSCvr46867

A Cisco ACI modular spine switch (N9504 chassis) with redundant supervisor modules (N9K-SUP-A) had an unexpected series of switchovers during a 6 minute period.

14.2(3j)

CSCvr47042

After removing a transceiver or cable from the interface, the port LED remains green. A port is physically down, but the "show interface" command says that the port is still up.

14.2(3j)

CSCvr49904

Traffic with a UDP destination port of 8472 is dropped on ingress by the ACI fabric.

14.2(3j)

CSCvr50031

The iBash "show interface ethernet <portnum>" command does not show CRC and stomped CRC errors.

14.2(3j)

CSCvr51479

MAC counters are reset when using the port shutdown command on the N9K-C9316D-GX and N9K-C93600CD-GX platforms . As a result, the MAC counters are not preserved.

14.2(3j)

CSCvr52832

There are no aggregated stats from L3If to L3ExtOut.

14.2(3j)

CSCvr57536

A Cisco ACI switch reloads due to a Machine Check Exception similar to the following output:

[603029.390562] sbridge: HANDLING MCE MEMORY ERROR

[603029.390563] CPU 0: Machine Check Exception: 0 Bank 7: 8c00004000010091

[603029.390564] TSC 0 ADDR 2e3d3f40 MISC 140545486 PROCESSOR 0:50663 TIME 1569464793 SOCKET 0 APIC 0

[603029.390710] sbridge: HANDLING MCE MEMORY ERROR

14.2(3j)

CSCvr60813

If fabric bidirectional forwarding detection (BFD) is enabled, the tenant BFD flaps upon enabling or disabling priority flow control (PFC) globally on any class when the peer node is an N9K-C9316D-GX or N9K-C93600CD-GX switch.

14.2(3j)

CSCvr62348

There is a slow memory leak during line card insertion or removal, FEX reloads, or transceiver removal. This is issue occurs more frequently for copper ports. If the ethpm process exceeds 4 GB of memory, the switch may reload with the reason "Line card not responding => [Failures < MAX] : powercycle" or "ethpm hap reset".

14.2(3j)

CSCvr75413

After upgrading a leaf switch, the switch brings up the front panel ports before the policies are programmed. This may cause a connectivity issue if a connected host relies on the link level state to decide whether or not it can forward traffic on a particular NIC or port. The loss duration would be proportional to the scale of configuration policies that must be programmed.

14.2(3j)

CSCvr80292

A remote leaf switch is stuck in the "inactive" state after being registered into the fabric.

14.2(3j)

CSCvr84189

10Gbase-ER optics will not link up.

14.2(3j)

CSCvr86930

When PoE is configured on ports on doing a stateful reload--that is, manually reloading a switch with the config restore option--a PoE power adjust can happen during the same interval when APIC discovery occurs. This results in a PoE core, as it expects the objstore always to return a desired interface object that may have been updated.

14.2(3j)

CSCvr87506

A leaf switch reboots 2 times, and on the 2nd reboot the state is not preserved. This causes the front panel ports to come online before being correctly configured and connected into the fabric, which can have traffic impact.

14.2(3j)

CSCvr87847

PIM border leaf switches do not see each other as PIM neighbors, resulting in potentially both being the stripe-winner and sending upstream joins. This can result in duplicate packets.

14.2(3j)

CSCvr88009

The Netflow (nfm) process crashes during configuration changes.

14.2(3j)

CSCvr95697

On a border leaf switch, some of the routes that are removed from the routing table are found to be not removed from BGP VPNv4 prefixes.

14.2(3j)

CSCvr98827

Some of the control plane packets are incorrectly classified as the user class and are reported as dropped in single chip spine switches. The statistics are incorrect because the packets are not actually dropped.

14.2(3j)

CSCvs02955

When running "show system internal epm endpoint all summary" on an FX leaf, the command output is cut short.

14.2(3j)

CSCvs04956

There is a memory leak with svc_ifc_streame.

14.2(3j)

CSCvs08304

The spine outerdstip, which indicates that the egress TEP is connecting to the Tetration network, is not updated when an egress L3Out in the mgmt:inb VRF fails over to a redundant L3Out on another leaf switch.

14.2(3j)

CSCvs10395

Leaf switch downlinks all go down at one time due to FabricTrack.

14.2(3j)

CSCuo37016

When configuring the output span on a FEX Hif interface, all the layer 3 switched packets going out of that FEX Hif interface are not spanned. Only layer 2 switched packets going out of that FEX Hif are spanned.

14.2(3j) and later

CSCuo50533

When output span is enabled on a port where the filter is VLAN, multicast traffic in the VLAN that goes out of that port is not spanned.

14.2(3j) and later

CSCup65586

The show interface command shows the tunnel's Rx/Tx counters as 0.

14.2(3j) and later

CSCup82908

The show vpc brief command displays the wire-encap VLAN Ids and the show interface .. trunk command displays the internal/hardware VLAN IDs. Both VLAN IDs are allocated and used differently, so there is no correlation between them.

14.2(3j) and later

CSCup92534

Continuous "threshold exceeded" messages are generated from the fabric.

14.2(3j) and later

CSCuq39829

Switch rescue user ("admin") can log into fabric switches even when TACACS is selected as the default login realm.

14.2(3j) and later

CSCuq46369

An extra 4 bytes is added to the untagged packet with Egress local and remote SPAN.

14.2(3j) and later

CSCuq77095

When the command show ip ospf vrf <vrf_name> is run from bash on the border leaf, the checksum field in the output always shows a zero value.

14.2(3j) and later

CSCuq83910

When an IP address moves from one MAC behind one ToR to another MAC behind another ToR, even though the VM sends a GARP packet, in ARP unicast mode, this GARP packet is not flooded. As a result, any other host with the original MAC to IP binding sending an L2 packet will send to the original ToR where the IP was in the beginning (based on MAC lookup), and the packet will be sent out on the old port (location). Without flooding the GARP packet in the network, all hosts will not update the MAC-to-IP binding.

14.2(3j) and later

CSCuq92447

When modifying the L2Unknown Unicast parameter on a Bridge Domain (BD), interfaces on externally connected devices may bounce. Additionally, the endpoint cache for the BD is flushed and all endpoints will have to be re-learned.

14.2(3j) and later

CSCuq93389

If an endpoint has multiple IPs, the endpoint will not be aged until all IPs go silent. If one of the IP addresses is reassigned to another server/host, the fabric detects it as an IP address move and forwarding will work as expected.

14.2(3j) and later

CSCur01336

The power supply will not be detected after performing a PSU online insertion and removal (OIR).

14.2(3j) and later

CSCur81822

The access-port operational status is always "trunk".

14.2(3j) and later

CSCus18541

An MSTP topology change notification (TCN) on a flood domain (FD) VLAN may not flush endpoints learned as remote where the FD is not deployed.

14.2(3j) and later

CSCus29623

The transceiver type for some Cisco AOC (active optical) cables is displayed as ACU (active copper).

14.2(3j) and later

CSCus43167

Any TCAM that is full, or nearly full, will raise the usage threshold fault. Because the faults for all TCAMs on leaf switches are grouped together, the fault will appear even on those with low usage.

Workaround:  Review the leaf switch scale and reduce the TCAM usage. Contact TAC to isolate further which TCAM is full.

14.2(3j) and later

CSCus54135

The default route is not leaked by BGP when the scope is set to context. The scope should be set to Outside for default route leaking.

14.2(3j) and later

CSCus61748

If the TOR 1RU system is configured with the RED fan (the reverse airflow), the air will flow from front to back. The temperature sensor in the back will be defined as an inlet temperature sensor, and the temperature sensor in the front will be defined as an outlet temperature sensor.

If the TOR 1RU system is configured with the BLUE fan (normal airflow), the air will flow from back to front. The temperature sensor in the front will be defined as an inlet temperature sensor, and the temperature sensor in the back will be defined as outlet temperature sensor.

From the airflow perspective, the inlet sensor reading should always be less than the outlet sensor reading. However, in the TOR 1RU family, the front panel temperature sensor has some inaccurate readings due to the front panel utilization and configuration, which causes the inlet temperature sensor reading to be very close, equal, or even greater than the outlet temperature reading.

14.2(3j) and later

CSCut59020

If Backbone and NSSA areas are on the same leaf, and default route leak is enabled, Type-5 LSAs cannot be redistributed to the Backbone area.

14.2(3j) and later

CSCuu11347

Traffic from the orphan port to the vPC pair is not recorded against the tunnel stats.  Traffic from the vPC pair to the orphan port is recorded against the tunnel stats.

14.2(3j) and later

CSCuu11351

Traffic from the orphan port to the vPC pair is only updated on the destination node, so the traffic count shows as excess.

14.2(3j) and later

CSCuu66310

If a bridge domain "Multi Destination Flood" mode is configured as "Drop", the ISIS PDU from the tenant space will get dropped in the fabric.

14.2(3j) and later

CSCuv57302

Atomic counters on the border leaf do not increment for traffic from an endpoint group going to the Layer 3 out interface.

14.2(3j) and later

CSCuv57315

Atomic counters on the border leaf do not increment for traffic from the Layer 3 out interface to an internal remote endpoint group.

14.2(3j) and later

CSCuv57316

TEP counters from the border leaf to remote leaf nodes do not increment.

14.2(3j) and later

CSCuw09389

For direct server return operations, if the client is behind the Layer 3 out, the server-to-client response will not be forwarded through the fabric.

14.2(3j) and later

CSCux97329

With the common pervasive gateway, only the packet destination to the virtual MAC is being properly Layer 3 forwarded. The packet destination to the bridge domain custom MAC fails to be forwarded. This is causing issues with certain appliances that rely on the incoming packets’ source MAC to set the return packet destination MAC.

14.2(3j) and later

CSCuy00084

BCM does not have a stats option for yellow packets/bytes, and so BCM does not show in the switch or APIC GUI stats/observer.

14.2(3j) and later

CSCuy02543

Bidirectional Forwarding Detection (BFD) echo mode is not supported on IPv6 BFD sessions carrying link-local as the source and destination IP address. BFD echo mode also is not supported on IPv4 BFD sessions over multihop or VPC peer links.

14.2(3j) and later

CSCuy06749

Traffic is dropped between two isolated EPGs.

14.2(3j) and later

CSCuy22288

The iping command’s replies get dropped by the QOS ingress policer.

14.2(3j) and later

CSCuy25780

An overlapping or duplicate prefix/subnet could cause the valid prefixes not to be installed because of batching behavior on a switch. This can happen during an upgrade to the 1.2(2) release.

14.2(3j) and later

CSCuy47634

EPG statistics only count total bytes and packets. The breakdown of statistics into multicast/unicast/broadcast is not available on new hardware.

14.2(3j) and later

CSCuy56975

You must configure different router MACs for SVI on each border leaf if L3out is deployed over port-channels/ports with STP and OSPF/OSPFv3/eBGP protocols are used. There is no need to configure different router MACs if you use VPC.

14.2(3j) and later

CSCuy61018

The default minimum bandwidth is used if the BW parameter is set to "0", and so traffic will still flow.

14.2(3j) and later

CSCuy96912

The debounce timer is not supported on 25G links.

14.2(3j) and later

CSCuz13529

With the N9K-C93180YC-EX switch, drop packets, such as MTU or storm control drops, are not accounted for in the input rate calculation.

14.2(3j) and later

CSCuz13614

For traffic coming out of an L3out to an internal EPG, stats for the actrlRule will not increment.

14.2(3j) and later

CSCuz13810

When subnet check is enabled, a ToR does not learn IP addresses locally that are outside of the bridge domain subnets. However, the packet itself is not dropped and will be forwarded to the fabric. This will result in such IP addresses getting learned as remote endpoints on other ToRs.

14.2(3j) and later

CSCuz47058

SAN boot over a virtual Port Channel or traditional Port Channel does not work.

14.2(3j) and later

CSCuz65221

A policy-based redirect (PBR) policy to redirect IP traffic also redirects IPv6 neighbor solicitation and neighbor advertisement packets.

14.2(3j) and later

CSCva98767

The front port of the QSA and GLC-T 1G module has a 10 to 15-second delay as it comes up from the insertion process.

14.2(3j) and later

CSCvb36823

If you have only one spine switch that is part of the infra WAN and you reload that switch, there can be drops in traffic. You should deploy the infra WAN on more than one spine switch to avoid this issue.

14.2(3j) and later

CSCvb39965

Slow drain is not supported on FEX Host Interface (HIF) ports.

14.2(3j) and later

CSCvb49451

In the case of endpoints in two different TOR pairs across a spine switch that are trying to communicate, an endpoint does not get relearned after being deleted on the local TOR pair. However, the endpoint still has its entries on the remote TOR pair.

14.2(3j) and later

CSCvd11146

Bridge domain subnet routes advertised out of the Cisco ACI fabric through an OSPF L3Out can be relearned in another node belonging to another OSPF L3Out on a different area.

14.2(3j) and later

CSCvd63567

After upgrading a switch, Layer 2 multicast traffic flowing across PODs gets affected for some of the bridge domain Global IP Outsides.

14.2(3j) and later

CSCvn94400

There is a traffic blackhole that lasts anywhere from a few seconds to a few mins after a border leaf switch is restored.

14.2(3j) and later

CSCvo39715

When downgrading a Cisco ACI fabric, the OSPF neighbors go down after downgrading the Cisco APICs from a 3.2 or later release to a pre-3.2 release. After the upgrade, the switches are still running a 13.2 or later release.

14.2(3j) and later

CSCvp04772

During an upgrade on a dual-SUP system, the standby SUP may go into a failed state.

14.2(3j) and later

CSCvq56811

Output packets that are ERSPAN'd still have the PTP header. Wireshark might not be able to decode the packets, and instead shows frames with ethertype 0x8988.

14.2(3j) and later

CSCvq71034

There is a policy drop that occurs with L3Out transit cases.

14.2(3j) and later

CSCvr12912

A switch reloads due to a sysmgr heartbeat failure and sysmgr HAP reset.

14.2(3j) and later

CSCvr61096

In a port group that has ports of mixed speeds, the first port in the port group that has valid optics present and is not in the admin down state is processed. The ports that come up later are brought up if they are using the same speed; otherwise, they are put in the hw-disabled state.

For example, if ports 14 and 15 are up and are using the 100G speed, then if ports 13 and 16 are using the 40G speed, these ports will be put in the hw-disabled state. After reloading or upgrading, you might not have the same interfaces in the port group in the UP state and in the hw-disabled state as you did before the reload or upgrade.

14.2(3j) and later

CSCvu42069

The event log shows VTEP tunnel down and up events. The down time and up time are the same, and there is no fault message.

14.2(3j) and later

N/A

Load balancers and servers must be Layer 2 adjacent. Layer 3 direct server return is not supported. If a load balancer and servers are Layer 3 adjacent, then they have to be placed behind the Layer 3 out, which works without a specific direct server return virtual IP address configuration.

14.2(3j) and later

N/A

IPN should preserve the CoS and DSCP values of a packet that enters IPN from the ACI spine switches. If there is a default policy on these nodes that change the CoS value based on the DSCP value or by any other mechanism, you must apply a policy to prevent the CoS value from being changed. At the minimum, the remarked CoS value should not be 4, 5, 6, or 7. If CoS is changed in the IPN, you must configure a DSCP-CoS translation policy in the APIC for the pod that translates queuing class information of the packet into the DSCP value in the outer header of the iVXLAN packet. You can also embed CoS by enabling CoS preservation. For more information, see the Cisco APIC and QoS KB article.

14.2(3j) and later

N/A

The following properties within a QoS class under "Global QoS Class policies" should not be changed from their default value and is only used for debugging purposes:

■        MTU (default – 9216 bytes)

■        Queue Control Method (default – Dynamic)

■        Queue Limit (default – 1522 bytes)

■        Minimum Buffers (default – 0)

14.2(3j) and later

N/A

The modular chassis Cisco ACI spine nodes, such as the Cisco Nexus 9508, support warm (stateless) standby where the state is not synched between the active and the standby supervisor modules. For an online insertion and removal (OIR) or reload of the active supervisor module, the standby supervisor module becomes active, but all modules in the switch are reset because the switchover is stateless. In the output of the show system redundancy status command, warm standby indicates stateless mode.

14.2(3j) and later

N/A

When a recommissioned APIC controller rejoins the cluster, GUI and CLI commands can time out while the cluster expands to include the recommissioned APIC controller.

14.2(3j) and later

N/A

If connectivity to the APIC cluster is lost while a switch is being decommissioned, the decommissioned switch may not complete a clean reboot. In this case, the fabric administrator should manually complete a clean reboot of the decommissioned switch.

14.2(3j) and later

N/A

Before expanding the APIC cluster with a recommissioned controller, remove any decommissioned switches from the fabric by powering down and disconnecting them. Doing so will ensure that the recommissioned APIC controller will not attempt to discover and recommission the switch.

14.2(3j) and later

N/A

Multicast router functionality is not supported when IGMP queries are received with VxLAN encapsulation.

14.2(3j) and later

N/A

IGMP Querier election across multiple Endpoint Groups (EPGs) or Layer 2 outsides (External Bridged Network) in a given bridge domain is not supported. Only one EPG or Layer 2 outside for a given bridge domain should be extended to multiple multicast routers if any.

14.2(3j) and later

N/A

The rate of the number of IGMP reports sent to a leaf switch should be limited to 1000 reports per second.

14.2(3j) and later

N/A

Unknown IP multicast packets are flooded on ingress leaf switches and border leaf switches, unless "unknown multicast flooding" is set to "Optimized Flood" in a bridge domain. This knob can be set to "Optimized Flood" only for a maximum of 50 bridge domains per leaf switch.

If "Optimized Flood" is enabled for more than the supported number of bridge domains on a leaf, follow these configuration steps to recover:

■        Set "unknown multicast flooding" to "Flood" for all bridge domains mapped to a leaf switch.

■        Set "unknown multicast flooding" to "Optimized Flood" on needed bridge domains.

14.2(3j) and later

N/A

Traffic destined to Static Route EP VIPs sourced from N9000 switches (switches with names that end in -EX) might not function properly because proxy route is not programmed.

14.2(3j) and later

N/A

An iVXLAN header of 50 bytes is added for traffic ingressing into the fabric. A bandwidth allowance of (50/50 + ingress_packet_size) needs to be made to prevent oversubscription from happening. If the allowance is not made, oversubscription might happen resulting in buffer drops.

14.2(3j) and later

N/A

An IP/MAC Ckt endpoint configuration is not supported in combination with static endpoint configurations.

14.2(3j) and later

N/A

An IP/MAC Ckt endpoint configuration is not supported with Layer 2-only bridge domains. Such a configuration will not be blocked, but the configuration will not take effect as there is no Layer 3 learning in these bridge domains.

14.2(3j) and later

N/A

An IP/MAC Ckt endpoint configuration is not supported with external and infra bridge domains because there is no Layer 3 learning in these bridge domains.

14.2(3j) and later

N/A

An IP/MAC Ckt endpoint configuration is not supported with a shared services provider configuration. The same or overlapping prefix cannot be used for a shared services provider and IP Ckt endpoint. However, this configuration can be applied in bridge domains having shared services consumer endpoint groups.

14.2(3j) and later

N/A

An IP/MAC Ckt endpoint configuration is not supported with dynamic endpoint groups. Only static endpoint groups are supported.

14.2(3j) and later

N/A

No fault will be raised if the IP/MAC Ckt endpoint prefix configured is outside of the bridge domain subnet range. This is because a user can configure bridge domain subnet and IP/MAC Ckt endpoint in any order and so this is not error condition. If the final configuration is such that a configured IP/MAC Ckt endpoint prefix is outside all bridge domain subnets, the configuration has no impact and is not an error condition.

14.2(3j) and later

N/A

Dynamic deployment of contracts based on instrImmedcy set to onDemand/lazy not supported; only immediate mode is supported.

14.2(3j) and later

N/A

When a server and load balancer are on the same endpoint group, make sure that the Server does not generate ARP/GARP/ND request/response/solicits. This will lead to learning of LB virtual IP (VIP) towards the Server and defeat the purpose of DSR support.

14.2(3j) and later

N/A

Direct server return is not supported for shared services. Direct server return endpoints cannot be spread around different virtual routing and forwarding (VRF) contexts.

14.2(3j) and later

N/A

Configurations for a virtual IP address can only be /32 or /128 prefix.

14.2(3j) and later

N/A

Client to virtual IP address (load balancer) traffic always will go through proxy-spine because fabric data-path learning of a virtual IP address does not occur.

14.2(3j) and later

N/A

GARP learning of a virtual IP address must be explicitly enabled. A load balancer can send GARP when it switches over from active-to-standby (MAC changes).

14.2(3j) and later

N/A

Learning through GARP will work only in ARP Flood Mode.

14.2(3j) and later

N9K-C9336PQ

The Cisco N9K-C9336PQ switch is supported for multipod.

The N9K-9336PQ switch is not supported for inter-site connectivity with Cisco ACI Multi-Site, but is supported for leaf switch-to-spine switch connectivity within a site.

The N9K-9336PQ switch is not supported when multipod and Cisco ACI Multi-Site are deployed together.

N9K-X9736C-FX

1-Gigabit QSA is not supported on ports 1/29-36. This line card supports the ability to add a fifth Fabric Module to the Cisco N9K-C9504 and N9K-C9508 switches. The fifth Fabric Module can only be inserted into slot 25.

N9K-C9348GC-FXP

This switch supports the following PSUs:

■        NXA-PAC-350W-PI

■        NXA-PAC-350W-PE

■        NXA-PAC-1100W-PI

■        NXA-PAC-1100W-PE

The following information applies to this switch:

■        Incoming FCOE packets are redirected by the supervisor module. The data plane-forwarded packets are dropped and are counted as forward drops instead of as supervisor module drops.

■        When a Cisco N9K-C9348GC-FXP switch has only one PSU inserted and connected, the PSU status for the empty PSU slot will be displayed as "shut" instead of "absent" due to a hardware limitation.

■        The PSU SPROM is not readable when the PSU is not connected. The model displays as "UNKNOWN" and status of the module displays as "shutdown."

N9K-C93180LC-EX

This switch has the following limitations:

■        The top and bottom ports must use the same speed. If there is a speed mismatch, the top port takes precedence and bottom port will be error disabled. Both ports both must be used in either the 40 Gbps or 10 Gbps mode.

■        Ports 26 and 28 are hardware disabled.

■        This release supports 40 and 100 Gbps for the front panel ports. The uplink ports can be used at the 100 Gbps speed.

■        Port profiles and breakout ports are not supported on the same port.

N9K-C9364C

You can deploy multipod or Cisco ACI Multi-Site separately (but not together) on the Cisco N9K-9364C switch starting in the 3.1 release.  You can deploy multipod and Cisco ACI Multi-Site together on the Cisco N9K-9364C switch starting in the 3.2 release.

A 930W-DC PSU (NXA-PDC-930W-PE or NXA-PDC-930W-PI) is supported in redundancy mode if 3.5W QSFP+ modules or passive QSFP cables are used and the system is used in 40C ambient temperature or less; for other optics or a higher ambient temperature, a 930W-DC PSU is supported only with 2 PSUs in non-redundancy mode.

1-Gigabit QSA is not supported on ports 1/49-64.

This switch supports the following PSUs:

■                    NXA-PAC-1200W-PE

■                    NXA-PAC-1200W-PI

■                    N9K-PUV-1200W

■                    NXA-PDC-930W-PE

■                    NXA-PDC-930W-PI

N9K-C9316D-GX

1G and 100MB speeds are not supported.

N9K-C93180YC-EX

The following FEC modes are not supported on N9K-C93180YC-EX ports 1 through 48 when running in 25G speed:

■        cl91-rs-fec

■        cons16-rs-fec

■        ieee-rs-fec

N9K-C9364C-GX

This switch has the following limitations:

■        The switch will power down in 2 minutes after the first fan failure. The switch can be powered up only after replacing the failed fan.

■        For ports 1-64, every 4 port 1-4,5-8...60-64 is referred as a quad. Each quad can be operated only with a fixed speed. For example: Ports 1-4 can operate only on 10G or 40G or 100G. Similarly, ports 60-64 can operate only on 10G or 40G or 100G.

■        You cannot use mixed speeds of 10G and 40G, 10G and 100G, or 40G and 100G in a quad (1-4,5-8...21-24). Based on the port bring up sequence, the port in the quad where a speed mismatch is detected will be HW disabled.

■        If there is a speed mismatch in a quad even when the ports are configured in the disabled state, the working links in that quad might get into the HW disabled state upon upgrading and reloading because the mixed speed is brought up first before the admin down configuration is pushed. As a result, you must manually perform the shut and no shut commands on the ports to bring up the links.

■        Breakout of 4x25G or 4X10G ports is not supported.

■        There is a lane selector button on the hardware. The button is used for the breakout port LED status. Because breakout is not supported, this button does nothing.

■        1G and 100MB speeds are not supported.

■        All 4 fans must be operational, otherwise the switch will power down due to a fan policy trigger.

N9K-C93600CD-GX

This switch has the following limitations:

■        For ports 1 through 24, every 4 ports (1-4, 5-8, 9-12, and so on, referred to as a "quad") will operate at a fixed speed. That is, all 4 ports will operate in 10G, or 40G, or 100G; you cannot mix the speeds.

■        Mixed speeds of 10G and 40G, or 10G and 100G, or 40G and 100G in a quad is not supported. Based on the port bring up sequence, the port in the quad where the speed mismatch is detected will be HW disabled.

■        If there is a speed mismatch in a quad even though the ports are configured in the disabled state, the working links in that quad might get into the HW disabled state upon upgrading or reloading, as the mixed speed is brought up first before admin down config is pushed. To avoid this issue, you must manually use the shut and no shut commands on the working ports to bring up the links. For more information, see bug CSCvr61096.

■        Ports 25-26 and ports 27-28 (port groups of 2 ports each) will operate in a fixed speed within the respective group, and you cannot mismatch the speed.

■        Uplink ports 29 to 36 do not have a mixed speed restriction; you can toggle the speed for the bidirectional ports.

■        For ports 1 to 28, even if you convert any ports to uplink with bidirectional optics, you cannot toggle the speed, as it will introduce mixed speeds and will disturb the neighboring ports.

■        For ports 1 to 28, if any of the ports are converted to uplink with bidirectional optics, the ports will stay in the not connected state if the peer is a 40G link.

■        4X10  and 4X25 breakout is supported on ports 25-28 and 29-34 (port profile converted downlinks).

■        Ports 25-26 and 27-28 form respective port pairs, and each pair can operate with 4X10, 10G, or 4X25G speed.

■        This switch does not support 4X100 breakout in this release.

■        The Hardware Abstraction Layer (HAL) will spike and the console can hang if a port channel or vPC exists when overlying breakout ports are deleted. To avoid this issue, delete the PC or vPC before deleting the overlying breakout policy.

■        1G and 100MB speeds are not supported.

N9K-C9332PQ

To connect the Cisco APIC to the Cisco ACI fabric, you must have a 10G interface on the ACI leaf switch. You cannot connect the APIC directly to the N9332PQ ACI leaf switch.

N9K-C93108TC-FX

Switch

Yes

No

N9K-C93180YC-FX

Switch

Yes

No

N9K-c93216TC-FX2

Switch

Yes

No

N9K-C93240YC-FX2

Switch

Yes

No

N9K-C9332C

Switch

Yes

Yes, only on the last 8 ports

N9K-C93360YC-FX2

Switch

Yes

No

N9K-C9336C-FX2

Switch

Yes

No

N9K-C9348GC-FXP

Switch

Yes, only with 10G+

No

N9K-C9364C

Switch

Yes

Yes, only on the last 16 ports

N9K-X9736C-FX

Line Card

Yes

Yes, only on the last 8 ports