Line Card Redundancy

The line cards support high availability with redundancy schemes. Line card redundancy can help limit customer premises equipment (CPE) downtime by enabling robust automatic switchover and recovery in the event that there is a localized system failure.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/. An account on http://www.cisco.com/ is not required.

Contents

Hardware Compatibility Matrix for Cisco cBR Series Routers


Note

The hardware components introduced in a given Cisco IOS-XE Release are supported in all subsequent releases unless otherwise specified.


Table 1. Hardware Compatibility Matrix for the Cisco cBR Series Routers

Cisco CMTS Platform

Processor Engine

Interface Cards

Cisco cBR-8 Converged Broadband Router

Cisco IOS-XE Release 3.15.0S and Later Releases

Cisco cBR-8 Supervisor :

  • PID—CBR-CCAP-SUP-160G

  • PID—CBR-CCAP-SUP-60G1

  • PID—CBR-SUP-8X10G-PIC

Cisco IOS-XE Release 3.15.0S and Later Releases

Cisco cBR-8 CCAP Line Cards:

  • PID—CBR-LC-8D30-16U30

  • PID—CBR-LC-8D31-16U30

  • PID—CBR-RF-PIC

  • PID—CBR-RF-PROT-PIC

Cisco cBR-8 Downstream PHY Modules:

  • PID—CBR-D30-DS-MOD

  • PID—CBR-D31-DS-MOD

Cisco cBR-8 Upstream PHY Modules:

  • PID—CBR-D30-US-MOD

1 Effective with Cisco IOS-XE Release 3.17.0S, CBR-CCAP-SUP-60G supports 8 cable line cards. The total traffic rate is limited to 60Gbps, the total number of downstream service flow is limited to 72268, and downstream unicast low-latency flow does not count against the limits.

Prerequisites for Line Card Redundancy

  • At least one RF Through PIC and its corresponding interface line card must be installed in the chassis to be configured as the primary card.

  • An RF Protect PIC and its corresponding interface line card must be installed in the chassis to be configured as the secondary card.

Restrictions for Line Card Redundancy

  • The line cards installed in slot 3 and 6 of the Cisco cBR-8 router cannot be configured as the secondary card.

  • The RF Protect PIC can send RF signals only to the lower slots (with larger slot number). So, the slot number of the secondary card must be the smallest in the redundancy group.


    Note

    We recommend that you install the RF Protect PIC in the uppermost slot (slot 0) of the chassis and configure it as the secondary card.


  • The RF Through PIC can send RF signal only from upper slot to lower slot. So, do not install any RF blank PICs between the secondary card and primary cards.

  • You cannot change any configuration on the primary or secondary card when the secondary card is active.

  • You cannot remove the last primary card if there is a secondary card in the redundancy group. You must remove the secondary card and then remove the primary card.

  • If the primary card is in the standby role, you must revert to the primary card before removing it from the redundancy group.

Information About Line Card Redundancy

Line card redundancy reduces the unplanned downtime. When you configure line card redundancy, a protect zone (redundancy group) is created on the router and the configurations on the primary cards are synchronized with the secondary card.

The following events can trigger a switchover from an active card to a standby card:

  • Manual switchover using the redundancy linecard-group switchover from slot slot command.

  • Line card reload using the hw-module slot reload command.

  • Line card crash.

  • Line card Online Insertion and Removal (OIR).

The secondary card reloads after the switchover. The router can be configured to automatically revert to the primary card when it becomes hot standby after an unplanned switchover triggered by the line card OIR or crash.

Following are the line card redundancy states:

  • Unavail—The line card state is not available.

  • Init—The line card did not boot up.

  • Active Cold—The active card is downloading the configuration.

  • Active—The active card is fully configured and working.

  • Stdby Cold—The standby card configuration is synchronizing with the active card.

  • Stdby Warm—(Only for the secondary card) The standby card is fully synchronized and ready for switchover. It is the stable state of a secondary standby card.

  • Stdby Hot—The primary standby card is fully synchronized. It is the stable state of a primary standby card. The secondary standby card is chosen to switchover for a primary card, and will be active soon. It is a transient state when secondary card is becoming active.

N+1 Line Card Redundancy

The Cisco cBR-8 router supports N+1 redundancy scheme for line cards. A single RF Protect PIC can be configured as a secondary card for multiple RF Through PICs (primary cards). In this redundancy scheme, when the secondary card becomes the active card for a primary card, the redundancy scheme is changed to 1+1 redundancy.

The Cisco cBR-8 router supports a single protect zone or redundancy group (group 0).

How to Configure Line Card Redundancy

This section contains the following:

Configuring Line Card Manual Switchover

Before you begin

The line card must be in active role, and warm standby or hot standby state. Use the show redundancy linecard all command to verify the role and state of the card.

Restrictions

  • You cannot perform a manual switchover when the standby Supervisor is booting up and not yet entered into SSO.

  • You cannot auto revert the switchover triggered manually.

Procedure

  Command or Action Purpose
Step 1

enable

Example:

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

redundancy linecard-group switchover from slot slot

Example:

Router# redundancy linecard-group switchover from slot 9

Manually switches over from the active line card.

Configuring N+1 Line Card Redundancy

Procedure

  Command or Action Purpose
Step 1

enable

Example:

Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.
Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

redundancy

Example:

Router(config)# redundancy

Enables redundancy and enters redundancy configuration mode.

Step 4

linecard-group group-id internal-switch

Example:

Router(config-red)# linecard-group 0 internal-switch

Configures the redundancy group and enters the line card redundancy configuration mode.

Step 5

description group-description

Example:

Router(config-red-lc)# description RedundancyGroup0

(Optional) Configures the redundancy group description.

Step 6

class 1:N

Example:

Router(config-red-lc)# class 1:N

Configures the N+1 redundancy class for the redundancy group.

Step 7

revertive seconds

Example:

Router(config-red-lc)# revertive 60

(Optional) Configures the auto revert time for the primary card, in seconds.

Step 8

member slot slot primary

Example:

Router(config-red-lc)# member slot 1 primary

Adds the line card as a primary card in the redundancy group.

Note 

Repeat this step for each primary card to be added in the redundancy group.

Step 9

member slot slot secondary

Example:

Router(config-red-lc)# member slot 0 secondary

Adds the line card as a primary card in the redundancy group.

Step 10

end

Example:

Router(config-red-lc)# end

Returns to privileged EXEC mode.

Verifying the Line Card Redundancy Configuration

  • show redundancy linecard group all —Displays the redundancy group information.

    The following is a sample output of this command:

    Router# show redundancy linecard group all
    
    Group Identifier: 0  
    Revertive, Revert Timer: OFF (60000 sec)
    Reserved Cardtype: 0xFFFFFFFF  4294967295
    Group Redundancy Type: INTERNAL SWITCH
    Group Redundancy Class: 1:N
    Group Redundancy Configuration Type: LINECARD GROUP
    Primary: Slot 6 
    Primary: Slot 7 
    Secondary: Slot 0
    
    
  • show redundancy linecard all —Displays the role and state information for all line cards.

    Following is a sample output of this command:

    Router# show redundancy linecard all 
    
                  LC     My         Peer       Peer     Peer
    Slot Subslot  Group  State      State      Slot     Subslot  Role     Mode     
    -------------------------------------------------------------------------------
     9   -        0      Active     Stdby Cold 0        -        Active   Primary  
     8   -        0      Active     Stdby Warm 0        -        Active   Primary  
     7   -        0      Active     Stdby Warm 0        -        Active   Primary  
     6   -        0      Active     Stdby Cold 0        -        Active   Primary  
     3   -        0      Active     Stdby Cold 0        -        Active   Primary  
     2   -        0      Active     Stdby Cold 0        -        Active   Primary  
     1   -        0      Active     Stdby Cold 0        -        Active   Primary  
     0   -        0      -          -          Multiple None     Standby  Secondary
    
    

    Note

    The secondary card does not have a valid My State when it is in Standby role as it is the peer for N primary cards. The secondary card has N peer states. For example, it can be cold standby for some primary cards and warm standby for the other primary card.


    Following is a sample output of the command when secondary card becomes active for a primary card, and the N+1 redundancy is changed to 1+1 redundancy:

    Router# show redundancy linecard all 
    
                  LC     My         Peer       Peer     Peer
    Slot Subslot  Group  State      State      Slot     Subslot  Role     Mode     
    -------------------------------------------------------------------------------
     9   -        0      Stdby Hot  Active     0        -        Standby  Primary  
     8   -        0      Active     Unavail    0        -        Active   Primary  
     7   -        0      Active     Unavail    0        -        Active   Primary  
     6   -        0      Active     Unavail    0        -        Active   Primary  
     3   -        0      Active     Unavail    0        -        Active   Primary  
     2   -        0      Active     Unavail    0        -        Active   Primary  
     1   -        0      Active     Unavail    0        -        Active   Primary  
     0   -        0      Active     Stdby Hot  9        -        Active   Secondary
    
    
  • show redundancy linecard slot —Displays the redundancy information for the line card.

    Following is a sample output of the command:

    Router# show redundancy linecard slot 9
    
     LC Redundancy Is Configured:
     LC Group Number: 0
     LC Slot: 9 (idx=9)
     LC Peer Slot: 0
     LC Card Type: 0x4076 , 16502
     LC Name: 9
     LC Mode: Primary
     LC Role: Active
     LC My State: Active
     LC Peer State: Stdby Warm
    
    
  • show redundancy linecard history —Displays the state change history for all line cards.

    Following is a sample output of the command:

    Router# show redundancy linecard history
    
    Jan 05 2012 12:24:27 20559 - st_mem(9): MY State Change, (Active Wait) -> (Active)
    Jan 05 2012 12:24:27 20559 - st_mem(9): MY FSM execution, Active Wait:Init:State Ntfy
    Jan 05 2012 12:24:27 20559 - st_mem(9): MY State Change, (Active LC Cfg Dnld) -> (Active Wait)
    Jan 05 2012 12:24:27 20559 - st_mem(9): MY FSM execution, Active LC Cfg Dnld:Init:Cfg Dnld Done
    Jan 05 2012 12:24:27 20559 - st_mem(9): MY State Change, (Active Cold) -> (Active LC Cfg Dnld)
    Jan 05 2012 12:23:09 12763 - st_mem(9): MY FSM execution, Active Cold:Init:Cfg Dnld
    Jan 05 2012 12:23:09 12760 - st_mem(9): MY State Change, (Init) -> (Active Cold)
    Jan 05 2012 12:23:09 12760 - st_mem(9): MY FSM execution, Init:Init:Up
    Jan 05 2012 12:21:39 3746 - st_mem(9): PEER FSM Execution , Init:Init:Reset
    
    
  • show lcha rfsw —Displays the internal RF switch PIC state information.

    Following is a sample output of the command:

    Router# show lcha rfsw 
    
    Slot 0 ==================================== 
    Type : Secondary PIC State: normal 
    Slot 1 ==================================== 
    Type : Primary PIC State: normal
    
    
  • show lcha logging level —Displays the cable modem line card logs.

    Following is a sample output of the command:

    Router# show lcha logging level noise
    
    11:02:03.313 CST Tue Nov 18 2014 [error] [slot=3] [txn=229] Peer-Up Message [tag=1011] to slot 3 complete [36144 ms]; status=nak response
    11:02:03.313 CST Tue Nov 18 2014 [error] [slot=0] [txn=229] Slot 0 downloaded configuration for slot 3; result=peer-up notification failed
    11:02:03.316 CST Tue Nov 18 2014 [noise] [slot=0] [txn=none] lcha_plfm_get_max_port_count_for_slot: slot 0 maximum port count is 1794
    11:02:03.316 CST Tue Nov 18 2014 [noise] [slot=0] [txn=none] lcha_plfm_get_starting_port_index: slot 0 starting port count is 0
    11:02:03.331 CST Tue Nov 18 2014 [note]  [slot=0] [txn=none] Slot 0 is being reset
    11:02:04.352 CST Tue Nov 18 2014 [note]  [slot=0] [txn=none] slot 0 removed
    
    
  • When the secondary card is active, you can use the slot number of either the primary or secondary card in the show commands.

    Following is a sample output of the show interfaces command after the primary card in slot 8 switches over to secondary card in slot 0:

    Router# show interfaces c0/0/0
    
    Cable0/0/0 is up, line protocol is up 
      Hardware is CMTS MD interface, address is 0000.0000.031e (bia 0000.0000.031e)
      MTU 1500 bytes, BW 26000 Kbit/sec, DLY 1000 usec, 
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation MCNS, loopback not set
      Keepalive set (10 sec)
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input never, output never, output hang never
      Last clearing of "show interface" counters never
      Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: weighted fair
      Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
         Conversations  0/0/256 (active/max active/max total)
         Reserved Conversations 0/0 (allocated/max allocated)
         Available Bandwidth 19500 kilobits/sec
      5 minute input rate 0 bits/sec, 0 packets/sec
      5 minute output rate 13000 bits/sec, 17 packets/sec
         0 packets input, 0 bytes, 0 no buffer
         Received 0 broadcasts (0 multicasts)
         0 runts, 0 giants, 0 throttles 
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
         140520 packets output, 14052672 bytes, 0 underruns
         0 output errors, 0 collisions, 1 interface resets
         0 unknown protocol drops
         0 output buffer failures, 0 output buffers swapped out
    
    Router# show interfaces c8/0/0
    
    Cable0/0/0 is up, line protocol is up 
      Hardware is CMTS MD interface, address is 0000.0000.031e (bia 0000.0000.031e)
      MTU 1500 bytes, BW 26000 Kbit/sec, DLY 1000 usec, 
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation MCNS, loopback not set
      Keepalive set (10 sec)
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input never, output never, output hang never
      Last clearing of "show interface" counters never
      Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: weighted fair
      Output queue: 0/1000/64/0 (size/max total/threshold/drops) 
         Conversations  0/0/256 (active/max active/max total)
         Reserved Conversations 0/0 (allocated/max allocated)
         Available Bandwidth 19500 kilobits/sec
      5 minute input rate 0 bits/sec, 0 packets/sec
      5 minute output rate 14000 bits/sec, 18 packets/sec
         0 packets input, 0 bytes, 0 no buffer
         Received 0 broadcasts (0 multicasts)
         0 runts, 0 giants, 0 throttles 
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
         140616 packets output, 14062272 bytes, 0 underruns
         0 output errors, 0 collisions, 1 interface resets
         0 unknown protocol drops
         0 output buffer failures, 0 output buffers swapped out
    
    
  • When the secondary card is active, the show running-config command displays the output for the secondary card.


    Note

    The output of the show running-config command is empty for the primary card when the secondary card is active.


    Following is a sample output of the show running-config command after the primary card in slot 8 switches over to secondary card in slot 0:

    Router# show running-config | begin controller Upstream-Cable 0
    
    controller Upstream-Cable 0/0/0
     us-channel 0 channel-width 1600000 1600000
     us-channel 0 docsis-mode atdma
     us-channel 0 minislot-size 4
     us-channel 0 modulation-profile 221
     no us-channel 0 shutdown
     us-channel 1 channel-width 1600000 1600000
     us-channel 1 docsis-mode atdma
    
    Router# show running-config | begin controller Upstream-Cable 8
    Router# 
    Router#
    
    

Additional References

Related Documents

Related Topic Document Title
CMTS commands Cisco CMTS Cable Command Reference

Technical Assistance

Description Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/support

Feature Information for Line Card Redundancy

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/. An account on http://www.cisco.com/ is not required.


Note

The below table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.


Table 2. Feature Information for Line Card Redundancy

Feature Name

Releases

Feature Information

N+1 Line Card Redundancy

Cisco IOS-XE Release 3.16.0S

This feature was introduced on the Cisco cBR Series Converged Broadband Router s.