Creating an IP Access List to Filter IP Options, TCP Flags, Noncontiguous Ports

This module describes how to use an IP access list to filter IP packets that contain certain IP Options, TCP flags, noncontiguous ports.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/. An account on http://www.cisco.com/ is not required.

Contents

Hardware Compatibility Matrix for Cisco cBR Series Routers


Note

The hardware components introduced in a given Cisco IOS-XE Release are supported in all subsequent releases unless otherwise specified.


Table 1. Hardware Compatibility Matrix for the Cisco cBR Series Routers

Cisco CMTS Platform

Processor Engine

Interface Cards

Cisco cBR-8 Converged Broadband Router

Cisco IOS-XE Release 3.15.0S and Later Releases

Cisco cBR-8 Supervisor :

  • PID—CBR-CCAP-SUP-160G

  • PID—CBR-CCAP-SUP-60G1

  • PID—CBR-SUP-8X10G-PIC

Cisco IOS-XE Release 3.15.0S and Later Releases

Cisco cBR-8 CCAP Line Cards:

  • PID—CBR-LC-8D30-16U30

  • PID—CBR-LC-8D31-16U30

  • PID—CBR-RF-PIC

  • PID—CBR-RF-PROT-PIC

Cisco cBR-8 Downstream PHY Modules:

  • PID—CBR-D30-DS-MOD

  • PID—CBR-D31-DS-MOD

Cisco cBR-8 Upstream PHY Modules:

  • PID—CBR-D30-US-MOD

1 Effective with Cisco IOS-XE Release 3.17.0S, CBR-CCAP-SUP-60G supports 8 cable line cards. The total traffic rate is limited to 60Gbps, the total number of downstream service flow is limited to 72268, and downstream unicast low-latency flow does not count against the limits.

Prerequisites for Creating an IP Access List to Filter IP Options TCP Flags Noncontiguous Ports or TTL Values

Before you perform any of the tasks in this module, you should be familiar with the information in the following modules:

  • “IP Access List Overview”

  • “Creating an IP Access List and Applying It to an Interface”

Information About Creating an IP Access List to Filter IP Options, TCP Flags, Noncontiguous Ports or TTL Values

IP Options

IP uses four key mechanisms in providing its service: Type of Service, Time to Live, Options, and Header Checksum.

The Options, commonly referred to as IP Options, provide for control functions that are required in some situations but unnecessary for the most common communications. IP Options include provisions for time stamps, security, and special routing.

IP Options may or may not appear in datagrams. They must be implemented by all IP modules (host and gateways). What is optional is their transmission in any particular datagram, not their implementation. In some environments the security option may be required in all datagrams.

The option field is variable in length. There may be zero or more options. IP Options can have one of two formats:

  • Format 1: A single octet of option-type.

  • Format 2: An option-type octet, an option-length octet, and the actual option-data octets.

The option-length octet counts the option-type octet, the option-length octet, and the option-data octets.

The option-type octet is viewed as having three fields: a 1-bit copied flag, a 2-bit option class, and a 5-bit option number. These fields form an 8-bit value for the option type field. IP Options are commonly referred to by their 8-bit value.

For a complete list and description of IP Options, refer to RFC 791, Internet Protocol at the following URL: http://www.faqs.org/rfcs/rfc791.html

Benefits of Filtering IP Options

  • Filtering of packets that contain IP Options from the network relieves downstream devices and hosts of the load from options packets.

  • This feature also minimizes load to the Route Processor (RP) for packets with IP Options that require RP processing on distributed systems. Previously, the packets were always routed to or processed by the RP CPU. Filtering the packets prevents them from impacting the RP.

Benefits of Filtering on TCP Flags

The ACL TCP Flags Filtering feature provides a flexible mechanism for filtering on TCP flags. Previously, an incoming packet was matched as long as any TCP flag in the packet matched a flag specified in the access control entry (ACE). This behavior allows for a security loophole, because packets with all flags set could get past the access control list (ACL). The ACL TCP Flags Filtering feature allows you to select any combination of flags on which to filter. The ability to match on a flag set and on a flag not set gives you a greater degree of control for filtering on TCP flags, thus enhancing security.

Because TCP packets can be sent as false synchronization packets that can be accepted by a listening port, it is recommended that administrators of firewall devices set up some filtering rules to drop false TCP packets.

The ACEs that make up an access list can be configured to detect and drop unauthorized TCP packets by allowing only the packets that have a very specific group of TCP flags set or not set. The ACL TCP Flags Filtering feature provides a greater degree of packet-filtering control in the following ways:

  • You can select any desired combination of TCP flags on which to filter TCP packets.

  • You can configure ACEs to allow matching on a flag that is set, as well as on a flag that is not set.

TCP Flags

The table below lists the TCP flags, which are further described in RFC 793, Transmission Control Protocol.

Table 2. TCP Flags

TCP Flag

Purpose

ACK

Acknowledge flag—Indicates that the acknowledgment field of a segment specifies the next sequence number the sender of this segment is expecting to receive.

FIN

Finish flag—Used to clear connections.

PSH

Push flag—Indicates the data in the call should be immediately pushed through to the receiving user.

RST

Reset flag—Indicates that the receiver should delete the connection without further interaction.

SYN

Synchronize flag—Used to establish connections.

URG

Urgent flag—Indicates that the urgent field is meaningful and must be added to the segment sequence number.

Benefits of Using the Named ACL Support for Noncontiguous Ports on an Access Control Entry Feature

This feature greatly reduces the number of access control entries (ACEs) required in an access control list to handle multiple entries for the same source address, destination address, and protocol. If you maintain large numbers of ACEs, use this feature to consolidate existing groups of access list entries wherever it is possible and when you create new access list entries. When you configure access list entries with noncontiguous ports, you will have fewer access list entries to maintain.

How Filtering on TTL Value Works

IP extended named and numbered access lists may filter on the TTL value of packets arriving at or leaving an interface. Packets with any possible TTL values 0 through 255 may be permitted or denied (filtered). Like filtering on other fields, such as source or destination address, the ip access-group command specifies in or out , which makes the access list ingress or egress and applies it to incoming or outgoing packets, respectively. The TTL value is checked in conjunction with the specified protocol, application, and any other settings in the access list entry, and all conditions must be met.

Special Handling for Packets with TTL Value of 0 or 1 Arriving at an Ingress Interface

The software switching paths—distributed Cisco Express Forwarding (dCEF), CEF, fast switching, and process switching—will usually permit or discard the packets based on the access list statements. However, when the TTL value of packets arriving at an ingress interface have a TTL of 0 or 1, special handling is required. The packets with a TTL value of 0 or 1 get sent to the process level before the ingress access list is checked in CEF, dCEF, or the fast switching paths. The ingress access list is applied to packets with TTL values 2 through 255 and a permit or deny decision is made.

Packets with a TTL value of 0 or 1 are sent to the process level because they will never be forwarded out of the device; the process level must check whether each packet is destined for the device and whether an Internet Control Message Protocol (ICMP) TTL Expire message needs to be sent back. This means that even if an ACL with TTL value 0 or 1 filtering is configured on the ingress interface with the intention to drop packets with a TTL of 0 or 1, the dropping of the packets will not happen in the faster paths. It will instead happen in the process level when the process applies the ACL. This is also true for hardware switching platforms. Packets with TTL value of 0 or 1 are sent to the process level of the route processor (RP) or Multilayer Switch Feature Card (MSFC).

On egress interfaces, access list filtering on TTL value works just like other access list features. The check will happen in the fastest switching path enabled in the device. This is because the faster switching paths handle all the TTL values (0 through 255) equally on the egress interface.

Control Plane Policing for Filtering TTL Values 0 and 1

The special behavior for packets with a TTL value of 0 or 1 results in higher CPU usage for the device. If you are filtering on TTL value of 0 or 1, you should use control plane policing (CPP) to protect the CPU from being overwhelmed. In order to leverage CPP, you must configure an access list especially for filtering TTL values 0 and 1 and apply the access list through CPP. This access list will be a separate access list from any other interface access lists. Because CPP works for the entire system, not just on individual interfaces, you would need to configure only one such special access list for the entire device. This task is described in the section "Enabling Control Plane Policing to Filter on TTL Values 0 and 1".

Benefits of Filtering on TTL Value

  • Filtering on time-to-live (TTL) value provides a way to control which packets are allowed to reach the device or are prevented from reaching the device. By looking at your network layout, you can choose whether to accept or deny packets from a certain device based on how many hops away it is. For example, in a small network, you can deny packets from a location more than three hops away. Filtering on TTL value allows you to validate if the traffic originated from a neighboring device. You can accept only packets that reach you in one hop, for example, by accepting only packets with a TTL value of one less than the initial TTL value of a particular protocol.

  • Many control plane protocols communicate only with their neighbors, but receive packets from everyone. By applying an access list that filters on TTL to receiving routers, you can block unwanted packets.

  • The Cisco software sends all packets with a TTL value of 0 or 1 to the process level. The device must then send an Internet Control Message Protocol (ICMP) TTL value expire message to the source. By filtering packets that have a TTL value of 0 through 2, you can reduce the load on the process level.

How to Create an IP Access List to Filter IP Options TCP Flags Noncontiguous Ports or TTL Values

Filtering Packets That Contain IP Options

Complete these steps to configure an access list to filter packets that contain IP options and to verify that the access list has been configured correctly.


Note

  • The ACL Support for Filtering IP Options feature can be used only with named, extended ACLs.
  • Resource Reservation Protocol (RSVP) Multiprotocol Label Switching Traffic Engineering (MPLS TE), Internet Group Management Protocol Version 2 (IGMPV2), and other protocols that use IP options packets may not function in drop or ignore mode if this feature is configured.
  • On most Cisco devices, a packet with IP options is not switched in hardware, but requires control plane software processing (primarily because there is a need to process the options and rewrite the IP header), so all IP packets with IP options will be filtered and switched in software.

Procedure

  Command or Action Purpose
Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

ip access-list extended access-list-name

Example:

Device(config)# ip access-list extended mylist1

Specifies the IP access list by name and enters named access list configuration mode.

Step 4

[ sequence-number ] deny protocol source source-wildcard destination destination-wildcard [ option option-value ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:

Device(config-ext-nacl)# deny ip any any option traceroute

(Optional) Specifies a deny statement in named IP access list mode.

  • This access list happens to use a deny statement first, but a permit statement could appear first, depending on the order of statements you need.

  • Use the option keyword and option-value argument to filter packets that contain a particular IP Option.

  • In this example, any packet that contains the traceroute IP option will be filtered out.

  • Use the no sequence-number form of this command to delete an entry.

Step 5

[ sequence-number ] permit protocol source source-wildcard destination destination-wildcard [ option option-value ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:

Device(config-ext-nacl)# permit ip any any option security

Specifies a permit statement in named IP access list mode.

  • In this example, any packet (not already filtered) that contains the security IP option will be permitted.

  • Use the no sequence-number form of this command to delete an entry.

Step 6

Repeat Step 4 or Step 5 as necessary.

Allows you to revise the access list.

Step 7

end

Example:

Device(config-ext-nacl)# end

(Optional) Exits named access list configuration mode and returns to privileged EXEC mode.

Step 8

show ip access-lists access-list-name

Example:

Device# show ip access-lists mylist1

(Optional) Displays the contents of the IP access list.

What to Do Next

Apply the access list to an interface or reference it from a command that accepts an access list.


Note

To effectively eliminate all packets that contain IP Options, we recommend that you configure the global ip options drop command.


Filtering Packets That Contain TCP Flags

This task configures an access list to filter packets that contain TCP flags and verifies that the access list has been configured correctly.


Note

  • TCP flag filtering can be used only with named, extended ACLs.
  • The ACL TCP Flags Filtering feature is supported only for Cisco ACLs.
  • Previously, the following command-line interface (CLI) format could be used to configure a TCP flag-checking mechanism:
permit tcp any any rst The following format that represents the same ACE can now be used: permit tcp any any match-any +rst Both the CLI formats are accepted; however, if the new keywords match-all or match-any are chosen, they must be followed by the new flags that are prefixed with “ + ” or “ - ”. It is advisable to use only the old format or the new format in a single ACL. You cannot mix and match the old and new CLI formats.


Caution

If a device having ACEs with the new syntax format is reloaded with a previous version of the Cisco software that does not support the ACL TCP Flags Filtering feature, the ACEs will not be applied, leading to possible security loopholes.


Procedure

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

ip access-list extended access-list-name

Example:


Device(config)# ip access-list extended kmd1

Specifies the IP access list by name and enters named access list configuration mode.

Step 4

[ sequence-number ] permit tcp source source-wildcard [ operator [ port ]] destination destination-wildcard [ operator [ port ]] [ established | { match-any | match-all } { + | - } flag-name ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:


Device(config-ext-nacl)# permit tcp any any match-any +rst

Specifies a permit statement in named IP access list mode.

  • This access list happens to use a permit statement first, but a deny statement could appear first, depending on the order of statements you need.

  • Use the TCP command syntax of the permit command.

  • Any packet with the RST TCP header flag set will be matched and allowed to pass the named access list kmd1 in Step 3.

Step 5

[ sequence-number ] deny tcp source source-wildcard [ operator [ port ]] destination destination-wildcard [ operator [ port ]] [ established | { match-any | match-all } { + | - } flag-name ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:


Device(config-ext-nacl)# deny tcp any any match-all -ack -fin

(Optional) Specifies a deny statement in named IP access list mode.

  • This access list happens to use a permit statement first, but a deny statement could appear first, depending on the order of statements you need.

  • Use the TCP command syntax of the deny command.

  • Any packet that does not have the ACK flag set, and also does not have the FIN flag set, will not be allowed to pass the named access list kmd1 in Step 3.

  • See the deny (IP) command for additional command syntax to permit upper-layer protocols (ICMP, IGMP, TCP, and UDP).

Step 6

Repeat Step 4 or Step 5 as necessary, adding statements by sequence number where you planned. Use the no sequence-number command to delete an entry.

Allows you to revise the access list.

Step 7

end

Example:


Device(config-ext-nacl)# end

(Optional) Exits the configuration mode and returns to privileged EXEC mode.

Step 8

show ip access-lists access-list-name

Example:


Device# show ip access-lists kmd1

(Optional) Displays the contents of the IP access list.

  • Review the output to confirm that the access list includes the new entry.

Configuring an Access Control Entry with Noncontiguous Ports

Perform this task to create access list entries that use noncontiguous TCP or UDP port numbers. Although this task uses TCP ports, you could use the UDP syntax of the permit and deny commands to filter noncontiguous UDP ports.

Although this task uses a permit command first, use the permit and deny commands in the order that achieves your filtering goals.


Note

The ACL—Named ACL Support for Noncontiguous Ports on an Access Control Entry feature can be used only with named, extended ACLs.


Procedure

  Command or Action Purpose
Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 3

ip access-list extended access-list-name

Example:

Device(config)# ip access-list extended acl-extd-1

Specifies the IP access list by name and enters named access list configuration mode.

Step 4

[ sequence-number ] permit tcp source source-wildcard [ operator port [ port ]] destination destination-wildcard [ operator [ port ]] [ established { match-any | match-all } { + | - } flag-name ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:

Device(config-ext-nacl)# permit tcp any eq telnet ftp any eq 450 679

Specifies a permit statement in named IP access list configuration mode.

  • Operators include lt (less than), gt (greater than), eq (equal), neq (not equal), and range (inclusive range).

  • If the operator is positioned after the source and source-wildcard arguments, it must match the source port. If the operator is positioned after the destination and destination-wildcard arguments, it must match the destination port.

  • The range operator requires two port numbers. You can configure up to 10 ports after the eq and neq operators. All other operators require one port number.

  • To filter UDP ports, use the UDP syntax of this command.

Step 5

[ sequence-number ] deny tcp source source-wildcard [ operator port [ port ]] destination destination-wildcard [ operator [ port ]] [ established { match-any | match-all } { + | - } flag-name ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:

Device(config-ext-nacl)# deny tcp any neq 45 565 632

(Optional) Specifies a deny statement in named access list configuration mode.

  • Operators include lt (less than), gt (greater than), eq (equal), neq (not equal), and range (inclusive range).

  • If the operator is positioned after the source and source-wildcard arguments, it must match the source port. If the operator is positioned after the destination and destination-wildcard arguments, it must match the destination port.

  • The range operator requires two port numbers. You can configure up to 10 ports after the eq and neq operators. All other operators require one port number.

  • To filter UDP ports, use the UDP syntax of this command.

Step 6

Repeat Step 4 or Step 5 as necessary, adding statements by sequence number where you planned. Use the no sequence-number command to delete an entry.

Allows you to revise the access list.

Step 7

end

Example:

Device(config-ext-nacl)# end

(Optional) Exits named access list configuration mode and returns to privileged EXEC mode.

Step 8

show ip access-lists access-list-name

Example:

Device# show ip access-lists kmd1

(Optional) Displays the contents of the access list.

Consolidating Access List Entries with Noncontiguous Ports into One Access List Entry

Perform this task to consolidate a group of access list entries with noncontiguous ports into one access list entry.

Although this task uses TCP ports, you could use the UDP syntax of the permit and deny commands to filter noncontiguous UDP ports.

Although this task uses a permit command first, use the permit and deny commands in the order that achieves your filtering goals.

Procedure

  Command or Action Purpose
Step 1

enable

Example:

Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

show ip access-lists access-list-name

Example:

Device# show ip access-lists mylist1

(Optional) Displays the contents of the IP access list.

  • Review the output to see if you can consolidate any access list entries.

Step 3

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 4

ip access-list extended access-list-name

Example:

Device(config)# ip access-list extended mylist1

Specifies the IP access list by name and enters named access list configuration mode.

Step 5

no [ sequence-number ] permit protocol source source-wildcard destination destination-wildcard [ option option-name ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:

Device(config-ext-nacl)# no 10

Removes the redundant access list entry that can be consolidated.

  • Repeat this step to remove entries to be consolidated because only the port numbers differ.

  • After this step is repeated to remove the access list entries 20, 30, and 40, for example, those entries are removed because they will be consolidated into one permit statement.

  • If a sequence-number is specified, the rest of the command syntax is optional.

Step 6

[ sequence-number ] permit protocol source source-wildcard [ operator port [ port ]] destination destination-wildcard [ operator port [ port ]] [ option option-name ] [ precedence precedence ] [ tos tos ] [ log ] [ time-range time-range-name ] [ fragments ]

Example:

Device(config-ext-nacl)# permit tcp any neq 45 565 632 any eq 23 45 34 43

Specifies a permit statement in named access list configuration mode.

  • In this instance, a group of access list entries with noncontiguous ports was consolidated into one permit statement.

  • You can configure up to 10 ports after the eq and neq operators.

Step 7

Repeat Steps 5 and 6 as necessary, adding permit or deny statements to consolidate access list entries where possible. Use the no sequence-number command to delete an entry.

Allows you to revise the access list.

Step 8

end

Example:

Device(config-std-nacl)# end

(Optional) Exits named access list configuration mode and returns to privileged EXEC mode.

Step 9

show ip access-lists access-list-name

Example:

Device# show ip access-lists mylist1

(Optional) Displays the contents of the access list.

What To Do Next

Apply the access list to an interface or reference it from a command that accepts an access list.

Filtering Packets Based on TTL Value

Because access lists are very flexible, it is not possible to define only one combination of permit and deny commands to filter packets based on the TTL value. This task illustrates just one example that achieves TTL filtering. Configure the appropriate permit and deny statements that will accomplish your filtering plan.


Note

When the access list specifies the operation EQ or NEQ, depending on the Cisco software release in use on the device, the access lists can specify up to ten TTL values. The number of TTL values can vary by the Cisco software release.


Procedure

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

ip access-list extended access-list-name

Example:


Device(config)# ip access-list extended ttlfilter

Defines an IP access list by name.

  • An access list that filters on TTL value must be an extended access list.

Step 4

[sequence-number ] permit protocol source source-wildcard destination destination-wildcard [option option-name ] [precedence precedence ] [tos tos ] [ttl operator value ] [log ] [time-range time-range-name ] [fragments ]

Example:


Device(config-ext-nacl)# permit ip host 172.16.1.1 any ttl lt 2

Sets conditions to allow a packet to pass a named IP access list.

  • Every access list must have at least one permit statement.

  • This example permits packets from source 172.16.1.1 to any destination with a TTL value less than 2.

Step 5

Continue to add permit or deny statements to achieve the filtering you want.

--

Step 6

exit

Example:


Device(config-ext-nacl)# exit

Exits any configuration mode to the next highest mode in the command-line interface (CLI) mode hierarchy.

Step 7

interface type number

Example:


Device(config)# interface TenGigabitEthernet4/1/0

Configures an interface type and enters interface configuration mode.

Step 8

ip access-group access-list-name {in | out }

Example:


Device(config-if)# ip access-group ttlfilter in

Applies the access list to an interface.

Enabling Control Plane Policing to Filter on TTL Values 0 and 1

Perform this task to filter IP packets based on a TTL value of 0 or 1 and to protect the CPU from being overwhelmed. This task configures an access list for classification on TTL value 0 and 1, configures the Modular QoS Command-Line Interface (CLI) (MQC), and applies a policy map to the control plane. Any packets that pass the access list are dropped. This special access list is separate from any other interface access lists.

Because access lists are very flexible, it is not possible to define only one combination of permit and deny commands to filter packets based on the TTL value. This task illustrates just one example that achieves TTL filtering. Configure the appropriate permit and deny statements that will accomplish your filtering plan.

Procedure

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

ip access-list extended access-list-name

Example:


Device(config)# ip access-list extended ttlfilter

Defines an IP access list by name.

  • An access list that filters on a TTL value must be an extended access list.

Step 4

[ sequence-number ] permit protocol source source-wildcard destination destination-wildcard ttl operator value

Example:


Device(config-ext-nacl)# permit ip host 172.16.1.1 any ttl lt 2

Sets conditions to allow a packet to pass a named IP access list.

  • Every access list must have at least one permit statement.

  • This example permits packets from source 172.16.1.1 to any destination with a TTL value less than 2.

Step 5

Continue to add permit or deny statements to achieve the filtering you want.

The packets that pass the access list will be dropped.

Step 6

exit

Example:


Device(config-ext-nacl)# exit

Exits any configuration mode to the next highest mode in the CLI mode hierarchy.

Step 7

class-map class-map-name [ match-all | match-any ]

Example:


Device(config)# class-map acl-filtering

Creates a class map to be used for matching packets to a specified class.

Step 8

match access-group { access-group | name access-group-name }

Example:


Device(config-cmap)# match access-group name ttlfilter

Configures the match criteria for a class map on the basis of the specified access control list.

Step 9

exit

Example:


Device(config-cmap)# exit

Exits any configuration mode to the next highest mode in the CLI mode hierarchy.

Step 10

policy-map policy-map-name

Example:


Device(config)# policy-map acl-filter

Creates or modifies a policy map that can be attached to one or more interface to specify a service policy.

Step 11

class { class-name | class-default }

Example:


Device(config-pmap)# class acl-filter-class

Specifies the name of the class whose policy you want to create or change or to specify the default class (commonly known as the class-default class) before you configure its policy.

Step 12

drop

Example:


Device(config-pmap-c)# drop

Configures a traffic class to discard packets belonging to a specific class.

Step 13

exit

Example:


Device(config-pmap-c)# exit

Exits any configuration mode to the next highest mode in the CLI mode hierarchy.

Step 14

exit

Example:


Device(config-pmap)# exit

Exits any configuration mode to the next highest mode in the CLI mode hierarchy.

Step 15

control-plane

Example:


Device(config)# control-plane

Associates or modifies attributes or parameters that are associated with the control plane of the device.

Step 16

service-policy { input | output } policy-map-name

Example:


Device(config-cp)# service-policy input acl-filter

Attaches a policy map to a control plane for aggregate control plane services.

Configuration Examples for Filtering IP Options, TCP Flags, Noncontiguous Ports and TTL Values

Example: Filtering Packets That Contain IP Options

The following example shows an extended access list named mylist2 that contains access list entries (ACEs) that are configured to permit TCP packets only if they contain the IP Options that are specified in the ACEs:


ip access-list extended mylist2
 10 permit ip any any option eool
 20 permit ip any any option record-route
 30 permit ip any any option zsu
 40 permit ip any any option mtup

The show access-list command has been entered to show how many packets were matched and therefore permitted:


Device# show ip access-list mylist2
Extended IP access list test
10 permit ip any any option eool (1 match)
20 permit ip any any option record-route (1 match)
30 permit ip any any option zsu (1 match)
40 permit ip any any option mtup (1 match)

Example: Filtering Packets That Contain TCP Flags

The following access list allows TCP packets only if the TCP flags ACK and SYN are set and the FIN flag is not set:


ip access-list extended aaa
 permit tcp any any match-all +ack +syn -fin
 end

The show access-list command has been entered to display the ACL:


Device# show access-list aaa

Extended IP access list aaa
 10 permit tcp any any match-all +ack +syn -fin

Example: Creating an Access List Entry with Noncontiguous Ports

The following access list entry can be created because up to ten ports can be entered after the eq and neq operators:


ip access-list extended aaa
 permit tcp any eq telnet ftp any eq 23 45 34
 end

Enter the show access-lists command to display the newly created access list entry.


Device# show access-lists aaa

Extended IP access list aaa
 10 permit tcp any eq telnet ftp any eq 23 45 34

Example: Consolidating Some Existing Access List Entries into One Access List Entry with Noncontiguous Ports

The show access-lists command is used to display a group of access list entries for the access list named abc:


Device# show access-lists abc
Extended IP access list abc
 10 permit tcp any eq telnet any eq 450
 20 permit tcp any eq telnet any eq 679
 30 permit tcp any eq ftp any eq 450 
 40 permit tcp any eq ftp any eq 679

Because the entries are all for the same permit statement and simply show different ports, they can be consolidated into one new access list entry. The following example shows the removal of the redundant access list entries and the creation of a new access list entry that consolidates the previously displayed group of access list entries:


ip access-list extended abc
 no 10
 no 20
 no 30
 no 40
 permit tcp any eq telnet ftp any eq 450 679
 end

When the show access-lists command is reentered, the consolidated access list entry is displayed:


Device# show access-lists abc
Extended IP access list abc
 10 permit tcp any eq telnet ftp any eq 450 679

Example: Filtering on TTL Value

The following access list filters IP packets containing type of service (ToS) level 3 with time-to-live (TTL) values 10 and 20. It also filters IP packets with a TTL greater than 154 and applies that rule to noninitial fragments. It permits IP packets with a precedence level of flash and a TTL value not equal to 1, and it sends log messages about such packets to the console. All other packets are denied.


ip access-list extended incomingfilter
 deny ip any any tos 3 ttl eq 10 20
 deny ip any any ttl gt 154 fragments
 permit ip any any precedence flash ttl neq 1 log
!
interface TenGigabitEthernet4/1/0

ip access-group incomingfilter in

Example: Control Plane Policing to Filter on TTL Values 0 and 1

The following example configures a traffic class called acl-filter-class for use in a policy map called acl-filter. An access list permits IP packets from any source having a time-to-live (TTL) value of 0 or 1. Any packets matching the access list are dropped. The policy map is attached to the control plane.


ip access-list extended ttlfilter

 permit ip any any ttl eq 0 1

class-map acl-filter-class 

 match access-group name ttlfilter 

policy-map acl-filter

 class acl-filter-class

 drop

control-plane

 service-policy input acl-filter

Additional References

Related Documents

Related Topic

Document Title

Security commands

Cisco IOS Security Command Reference

Configuring the device to drop or ignore packets containing IP Options by using the no ip options command.

ACL IP Options Selective Drop

Overview information about access lists.

IP Access List Overview

Information about creating an IP access list and applying it to an interface

Creating an IP Access List and Applying It to an Interface

QoS commands

Cisco IOS Quality of Service Solutions Command Reference

RFCs

RFC

Title

RFC 791

Internet Protocol

http://www.faqs.org/rfcs/rfc791.html

RFC 793

Transmission Control Protocol

RFC 1393

Traceroute Using an IP Option

Technical Assistance

Description

Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for Creating an IP Access List to Filter IP Options, TCP Flags, Noncontiguous Ports, or TTL Values

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/. An account on http://www.cisco.com/ is not required.


Note

The below table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.


Table 3. Feature Information for Creating an IP Access List to Filter IP Options, TCP Flags, Noncontiguous Ports, or TTL Values

Feature Name

Releases

Feature Information

IP Access Lists

Cisco IOS-XE Release 3.15.0S

This feature was introduced on the Cisco cBR Series Converged Broadband Router s.