Introduction
This document describes the steps required to enable the license boot level for the Cisco Catalyst 8000V Edge Software. When you boot a Catalyst 8000V Edge Software instance for the first time, the mode router boots in depends on the release version. You must install the software license or enable an evaluation license to obtain the supported throughput and features. Based on the release version you must enable the boot level or change the maximum throughput level and reboot the device.
Prerequisites
Pre-deployed Catalyst 8000V Edge Software, registered with the Smart Licensing Using Policy.
Requirements
Cisco recommends that you have knowledge of these topics:
- Catalyst 8000V Edge Software basic configuration
- Smart Licensing Using Policy configuration
Components Used
The information in this document is based on these software versions:
- Catalyst 8000V Edge Software with Cisco IOS®-XE v17.4.1
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.
Background Information
In some Cat8000V Edge Software deployments that run Cisco IOS®-XE versions 17.4.x, the license boot level is not set. This causes problems with the license based features in the virtual router.
Here you have an example from where the boot level is not set:
Cat8000#show version
...
License Level:
License Type: Perpetual
Next reload license Level:
Addon License Level:
Addon License Type: Subscription
Next reload addon license Level:
You have three options to setup the boot level in the virtual router, Network-Advantage, Network-Essentials and Network-Premiere.
Cat8000#configure termial
Cat8000(config)#license boot level ?
network-advantage License Level Network-Advantage
network-essentials License Level Network-Essentials
network-premier License Level Network-Premier
You have three options to configure the addon, based on the boot level that you choose, DNA-Advantage, DNA-Essentials and DNA-Premiere.
Cat8000(config)#license boot level network-essentials addon ?
dna-essentials Add-on option DNA-Essentials
Cat8000(config)#license boot level network-premier addon ?
dna-premier Add-on option DNA-Premier
Cat8000(config)#license boot level network-advantage addon ?
dna-advantage Add-on option DNA-Advantage
Note: In order to check the features provided by each of the license boot levels and its addon you can review the next document. Cisco DNA Software Subscription Matrix for Switching
Configure
The Network-Essentials boot level with the DNA-Essentials addon is shown in this Catalyst 8000V Edge Software configuration example.
Configuration Steps
Step 1. In order to configure the Network-Essentials boot level, get into the router global configuration and apply the next command.
Cat8000#configure terminal
Cat8000(config)#license boot level network-essentials
Step 2. Then, setup the dna-essentials addon as follows.
Cat8000(config)#license boot level network-essentials addon dna-essentials
% use 'write' command to make license boot config take effect on next boot
Step 3. With the show version command you can verify the changes applied, but this takes effect on the next boot.
Cat8000#show version
...
License Level:
License Type: Perpetual
Next reload license Level: network-essentials
Addon License Level:
Addon License Type: Subscription
Next reload addon license Level: dna-essentials
Step 4. Save the configuration changes.
Cat8000#write
Step 5. You must reload the device for the changes to take effect.
Cat8000#reload
Verify
1. After the reload of the Catalyst 8000V Edge Software, use the show version command to verify the setup of the boot level and the addon.
Cat8000#show version
...
License Level: network-essentials
License Type: Perpetual
Next reload license Level: network-essentials
Addon License Level: dna-essentials
Addon License Type: Subscription
Next reload addon license Level: dna-essentials
2. Use the show license status command to check the Catalyst 8000V Edge Software is registered to Smart Licensing Using Policy.
Cat8000#show license status
Utility:
Status: DISABLED
Smart Licensing Using Policy:
Status: ENABLED
Data Privacy:
Sending Hostname: yes
Callhome hostname privacy: DISABLED
Smart Licensing hostname privacy: DISABLED
Version privacy: DISABLED
Transport:
Type: Smart
URL: https://smartreceiver.cisco.com/licservice/license
Proxy:
Not Configured
...
Usage Reporting:
Last ACK received: Apr 13 10:51:45 2021 EST
Next ACK deadline: Jun 12 10:51:45 2021 EST
3. Use the show license status command to ensure a trust code is installed for the smart trasport method, on the Trust Code Installed section, it must be updated with the registration date as follows.
Cat8000#show license status
...
Trust Code Installed: Apr 13 10:51:45 2021 EST
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
Related Information
Technical Support & Documentation - Cisco Systems
Configure Smart Licensing Using Policy on IOS-XE Routers
Feedback