Declarations of Conformity and Regulatory Information

This section provides declarations of conformity and regulatory information for the . You can find additional information at: https://www.cisco.com/c/dam/assets/prod/wireless/wireless-compliance-tool/index.html.

Manufacturers Federal Communication Commission declaration of conformity statement



Access Point model

Certification number

CW9171I

UDX-600219010

Manufacturer:

Cisco Systems, Inc.170 West Tasman Drive San Jose, CA 95134-1706 USA

This device complies with Part 15 rules. Operation is subject to the following conditions:

  1. This device may not cause harmful interference.

  2. This device must accept any interference received, including interference that may cause undesired operation.

  3. For 6 GHz operation, this device is classified as a Low Power Indoor (LPI) access point and must be operated indoors only. Operation of the 6 GHz band outdoors is prohibited under FCC rules. This restriction applies exclusively to 6 GHz operation and does not affect operation in other supported frequency bands, which remain subject to applicable FCC regulations.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna

  • Increase separation between the equipment and receiver

  • Connect the equipment to an outlet on a circuit different from which the receiver is connected

  • Consult the dealer or an experienced radio/TV technician

  • Professional Installation is recommended


Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Low power indoor access points and subordinate devices

  • FCC regulations restrict the operation of this device to indoor use only.

  • This device is prohibited from being operated on oil platforms, cars, trains, boats, and aircraft, except it can be operated in large aircraft while flying above 10,000 feet in the 5.925-6.425 GHz band.

  • Transmitters in the 5.925-7.125 GHz band are prohibited from operating to control or communicate with unmanned aircraft systems.

Standard power access points

  • The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft.

  • Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.

VCCI statement for Japan

Warning

Warning

 

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.



Warning

 


Access Point model:

CW9171I

Guidelines for operating Cisco Wireless Access Points in Japan

This section provides guidelines for avoiding interference when operating Cisco Wireless Access Points in Japan. These guidelines are provided in both Japanese and English.

この機器の使用周波数帯では、電子レンジ等の産業・科学・医療用機器のほかエ場の製造ライン等で使用されている移動体識別用の構内無線局（免許を要する無線局）及び特定小電力無線局（免許を要しない無線局）が運用されています。

  1. この機器を使用する前に、近くで移動体臓別用の構内無線局及び特定小電力無線局が運用されていないことを確認して下さい。

  2. 万一、この機器から移動体識別用の構内無線局に対して電波干渉の事例が発生した場合には、速やかに使用周波数を変更するか又は電波の発射を停止した上、下記連絡先にご連絡頂き、混信回避のための処置等（例えぱ、ノくーティションの設置など｝Iこついてご相談して下さい。

  3. その他、この機器から移動体撒別用の特定，ト電力無線局に対して電波干渉の事例が発生した場合など何かお困りのことが起きたときは、次の連絡先へお問い合わせ下さい。

    連絡先：03-6434-6500

English Translation

This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.

  1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.

  2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.

  3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.

    Contact Number: 03-6434-6500

Canadian compliance statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

  • This device may not cause interference.

  • This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

  • L’appareil ne doit pas produire de brouillage.

  • L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Wi-Fi 7 Device

For operation in the 5925–6425 MHz band, this device is classified as a Low Power Indoor (LPI) or Very Low Power (VLP) device under Innovation, Science and Economic Development Canada (ISED) RSS-247 and shall be operated in accordance with applicable indoor-use and platform-based restrictions defined by ISED. These restrictions apply exclusively to 6 GHz operation and include limitations related to indoor use and operation on aircraft, vehicles, trains, maritime vessels, oil platforms, and unmanned aircraft systems. Operation in the 2.4 GHz and 5 GHz bands is not subject to these restrictions and remains governed by the applicable ISED regulatory requirements for those bands.

appareil Wi-Fi 7

Pour le fonctionnement dans la bande 5925–6425 MHz, cet appareil est classé comme dispositif de faible puissance intérieur (LPI) ou de très faible puissance (VLP) conformément à la norme CNR-247 d’Innovation, Sciences et Développement économique Canada (ISDE) et doit être utilisé conformément aux restrictions applicables relatives à l’utilisation intérieure et aux plateformes définies par ISDE. Ces restrictions s’appliquent exclusivement au fonctionnement dans la bande de 6 GHz et comprennent des limitations liées à l’utilisation intérieure ainsi qu’à l’exploitation sur les aéronefs, les véhicules, les trains, les navires maritimes, les plateformes pétrolières et les systèmes d’aéronefs sans pilote. Le fonctionnement dans les bandes de 2,4 GHz et de 5 GHz n’est pas soumis à ces restrictions et demeure régi par les exigences réglementaires applicables d’ISDE pour ces bandes.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

The transmitter module may not be co-located with any other transmitter or antenna.

Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.

Low power indoor access points and indoor subordinate devices

  • Operation shall be limited to indoor use only.

  • Le fonctionnement doit être limitée à une utilisation à l'intérieur seulement.

Standard client devices

  • The antenna height shall be determined by the installer or operator of the standard-power access point or fixed client device, or by automatic means. This information shall be stored internally in the device. Provision of accurate device information is mandatory. Information for antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 4.5.4 (c) shall be clearly indicated.

  • La hauteur de l'antenne doit être déterminée par l'installateur ou l'opérateur du point d'accès de puissance normale ou du dispositif client fixe, ou par des dispositifs automatiques. Cette information doit être enregistrée dans le dispositif. La fourniture d'information précise sur le dispositif est obligatoire. le ou les types d'antennes, le ou les modèles d'antennes et le ou les pires angles d'inclinaison nécessaires pour rester conforme à l'exigence de la section 4.5.4 c. s'appliquant au masque de p.i.r.e. doivent être clairement indiqués.

Industry Canada

Access Point model

Certification number

CW9171I

6961A-600219010

European community, Switzerland, Norway, Iceland, and Liechtenstein compliance

The product carries the CE Mark:



When operating in the 5150–5350 MHz band and the 5945–6425 MHz band, this device is restricted to indoor use in accordance with applicable European Union and EFTA regulatory requirements. These restrictions apply exclusively to operation within the specified frequency bands and do not affect operation in other supported bands, which remain subject to national regulations.

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator & your body.


Note
This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.

Access Point model:

CW9171I

Manufacturer:

Cisco Systems, Inc., 170 West Tasman Drive San Jose, CA 95134-1706 USA

United Kingdom compliance

When operating in the 5150–5350 MHz band and the 5925–6425 MHz band, this device is restricted to indoor use in accordance with applicable United Kingdom regulatory requirements. These restrictions apply exclusively to operation within the specified frequency bands and do not affect operation in other supported bands, which remain subject to applicable UK regulations.

This equipment should be installed and operated with minimum distance 20 cm (7.87 inches) between the radiator & your body.

Access Point model:

CW9171I

Manufacturer:

Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA

Administrative rules for Cisco Wireless Access Points in Taiwan

This section provides administrative rules for operating Cisco Wireless Access Points in Taiwan. The rules for all access points are provided in both Simplified Chinese and English.

Simplified Chinese translation

【低功率射頻器材技術規範】取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。應避免影響附近雷達系統之操作。

【本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者】

English translation

Without permission granted by the National Communications Commission (NCC), no company, enterprise, or user shall alter the frequency, increase the transmitting power, or modify the original characteristics or performance of approved low-power radio-frequency devices.

Low-power radio-frequency devices shall not affect aviation safety or interfere with lawful communications. If interference is observed, operation shall be ceased immediately and shall not resume until the interference has been resolved. Lawful communications refer to radio communications operated in accordance with the Telecommunications Management Act.

Low-power radio-frequency devices must accept interference from lawful communications and from industrial, scientific, and medical (ISM) radio-frequency equipment. Operation shall avoid interference with nearby radar systems.

This equipment must be installed and configured by qualified professional personnel and is not intended for direct sale to the general public.

This section contains special information for the operation of Cisco Wireless Access Points in Taiwan.

Access Point model

Certification number

CW9171I

TBD

Operation of Cisco Wireless Access Points in Brazil

Figure 1. Brazil Regulatory Information

This section contains special information for operation of Cisco Wireless Access Points in Brazil.

Portuguese

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.

English

This equipment is not entitled to the protection from harmful interference and may not cause interference with duly authorized systems.

equipamento Wi-Fi 7

Para operação na faixa de 5925–6425 MHz, este equipamento é classificado como dispositivo de baixa potência para uso interno, conforme os requisitos regulatórios aplicáveis no Brasil. As restrições relacionadas ao uso interno e à operação em aeronaves, veículos, trens, embarcações e plataformas petrolíferas aplicam-se exclusivamente à operação na banda de 6 GHz e não afetam a operação do equipamento em outras faixas de frequência suportadas, que permanecem sujeitas às regulamentações brasileiras aplicáveis.

Wi-Fi 7 Device

For operation in the 5925–6425 MHz band, this device is classified as a low-power indoor device in accordance with applicable Brazilian regulatory requirements. Restrictions on indoor use and on the operation of aircraft, vehicles, trains, maritime vessels, and oil platforms apply exclusively to 6 GHz operations and do not affect operations in other supported frequency bands, which remain subject to applicable Brazilian regulations.

Access Point model

Certification number

CW9171I

TBD

Declaration of conformity for RF exposure

This section provides information on compliance with applicable regulatory requirements and international guidelines related to human exposure to radio frequency (RF) electromagnetic fields.

The Cisco CW9171I access point is designed to comply with applicable RF exposure requirements established by regulatory authorities and recognized international standards, including but not limited to:

  • United States: 47 CFR Part 2, Subpart J

  • Canada: Innovation, Science and Economic Development Canada (ISED) Safety Code 6

  • European Union: Council Recommendation 1999/519/EC and applicable EN standards based on ICNIRP guidelines

  • International: International Commission on Non-Ionizing Radiation Protection (ICNIRP) guidelines

  • Australia: Applicable Australian Radiation Protection standards

To ensure compliance with these requirements, the Cisco CW9171I shall be installed and operated using Cisco-approved antennas and accessories only. The device is intended to be installed in a manner that maintains a minimum separation distance of 20 cm (7.87 inches) between the radiating elements and all persons during normal operation, unless otherwise specified by applicable regional regulations.

The CW9171I includes radio transmitters and receivers and is designed to operate within established RF exposure limits, which incorporate substantial safety margins to ensure protection for all persons, regardless of age or health condition.

This device meets applicable international guidelines for exposure to radio frequency electromagnetic fields

The Cisco CW9171I device contains radio transmitters and receivers and is designed to operate within the limits for human exposure to radio waves established by applicable regulatory authorities and recognized international guidelines, which incorporate substantial safety margins to ensure the safety of all persons, regardless of age or health condition.

To maintain compliance with these requirements, the device shall be installed and operated in a manner that prevents direct contact with the antennas by the end user and maintains a minimum separation distance of 20 cm (7.87 inches) between the radiating elements and all persons during normal operation, unless otherwise specified by applicable regional regulations.

Separation Distance

20 cm (7.87 inches)

RF Exposure Compliance (FCC/ISED/International)

This device meets applicable regulatory requirements and international guidelines for human exposure to radio frequency electromagnetic fields.

The Cisco CW9171I access point contains radio transmitters and receivers and is designed to operate within the limits for RF exposure established by the Federal Communications Commission (FCC), Innovation, Science and Economic Development Canada (ISED), and other applicable regulatory authorities. These limits incorporate substantial safety margins to ensure the safety of all persons, regardless of age or health condition.

To maintain compliance with these requirements, the device shall be installed and operated in a manner that prevents direct contact with the antennas by the end user and maintains a minimum separation distance of 20 cm (7.87 inches) between the radiating elements and all persons during normal operation, unless otherwise specified by applicable regional regulations.

The device has been evaluated and found compliant with the applicable RF exposure requirements as part of the radio certification process.

Table 1. Minimum Separation Distance

Frequency Band

Minimum Separation distance

2.4 GHz / 5 GHz / 6 GHz

20 cm (7.87 inches)

Conformité à l’exposition aux radiofréquences – Canada

Cet appareil est conforme aux exigences réglementaires applicables et aux directives internationales en matière d’exposition humaine aux champs électromagnétiques de radiofréquence.

L’appareil Cisco CW9171I comprend des émetteurs et récepteurs radio et a été conçu pour fonctionner dans les limites d’exposition aux radiofréquences établies par Innovation, Sciences et Développement économique Canada (ISDE), notamment le Code de sécurité 6 de Santé Canada, ainsi que par d’autres autorités réglementaires applicables. Ces limites intègrent des marges de sécurité importantes afin d’assurer la protection de toutes les personnes, indépendamment de l’âge ou de l’état de santé.

Afin de maintenir la conformité à ces exigences, l’appareil doit être installé et utilisé de manière à empêcher tout contact direct entre les antennes et l’utilisateur final, et à maintenir la distance minimale d’éloignement indiquée ci-dessous entre les éléments rayonnants et toute personne durant le fonctionnement normal, sauf indication contraire prévue par les réglementations régionales applicables.

Table 2. Distance minimale d’éloignement

Bande de fréquences

Distance minimale d’éloignement

2.4 GHz / 5 GHz / 6 GHz

20 cm (7.87 inches)

Note

Remarque : La distance minimale d’éloignement s’applique à toutes les bandes de fréquences prises en charge durant le fonctionnement normal, sauf indication contraire prévue par les réglementations régionales applicables.

Additional information on RF exposure

You can find additional information on the subject at the following links:

You can obtain additional information from the following organizations:

Declaration of conformity statements

All the Declaration of Conformity statements related to this product can be found at the following location: https://pas.cisco.com/pdtcnc/#/