Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents

Find Matches in This Book

Results

Updated:: December 22, 2014

Chapter: Appendix C - Access Point Pinouts

Access Point Pinouts

This appendix describes the pin signals of the access point Ethernet connectors, and the power injector input and output connectors.

Table C-1 describes the pin signals of the access point LAN connector

Table C-1 Access Point LAN Connector Pinouts
Pin Number	Signal Name
1	Ethernet signal pair (10/100/1000BASE-T)
2	Ethernet signal pair (10/100/1000BASE-T)
3	Ethernet signal pair (10/100/1000BASE-T)
6	Ethernet signal pair (10/100/1000BASE-T)
4	Ethernet signal pair (10/100/1000BASE-T)
5	Ethernet signal pair (10/100/1000BASE-T)
7	Ethernet signal pair (10/100/1000BASE-T)
8	Ethernet signal pair (10/100/1000BASE-T)
Shield	Chassis ground

Table C-2 describes the pin signals for the access point PoE-in Ethernet connector. The Pinouts given in this table are applicable to AIR-POWERINJ1500. Not all PoE power sources follow these pinouts.

Table C-2 Access Point PoE-In Ethernet Connector Pinouts for AIR-POWERINJ1500
Pin Number	Signal Name
1	Ethernet signal pair (10/100/1000BASE-T) and DC return
2	Ethernet signal pair (10/100/1000BASE-T) and DC return
3	Ethernet signal pair (10/100/1000BASE-T) and DC (+)
6	Ethernet signal pair (10/100/1000BASE-T) and DC (+)
4	Ethernet signal pair (1000BASE-T) and DC (+)
5	Ethernet signal pair (1000BASE-T) and DC (+)
7	Ethernet signal pair (1000BASE-T) and DC return
8	Ethernet signal pair (1000BASE-T) and DC return
Shield	Chassis ground

Table C-3 describes the pin signals for the power injector input connector (To Switch).

Table C-3 Power Injector Input Connector (To Switch) Pinouts
Pin Number	Signal Name
1	Ethernet signal pair (10/100/1000BASE-T)
2	Ethernet signal pair (10/100/1000BASE-T)
3	Ethernet signal pair 10/100/1000BASE-T)
6	Ethernet signal pair 10/100/1000BASE-T)
4	Ethernet signal pair (1000BASE-T)
5	Ethernet signal pair (1000BASE-T)
7	Ethernet signal pair (1000BASE-T)
8	Ethernet signal pair (1000BASE-T)
Shield	Chassis ground

Table C-4 describes the RJ-45 pin signals for the power injector output connector (To AP). The Pinouts given in this table are applicable to AIR-POWERINJ1500. Not all PoE power sources follow these pinouts.

Table C-4 Power Injector AIR-POWERINJ1500 Output Connector (To AP) Pinouts
Pin Number	Signal Name
1	Ethernet signal pair (10/100/1000BASE-T) and DC return
2	Ethernet signal pair (10/100/1000BASE-T) and DC return
3	Ethernet signal pair (10/100/1000BASE-T) and DC (+)
6	Ethernet signal pair (10/100/1000BASE-T) and DC (+)
4	Ethernet signal pair (1000BASE-T) and DC (+)
5	Ethernet signal pair (1000BASE-T) and DC (+)
7	Ethernet signal pair (1000BASE-T) and DC return
8	Ethernet signal pair (1000BASE-T) and DC return
Shield	Chassis ground

Was this Document Helpful?

Feedback

Contact Cisco

Open a Support Case
(Requires a Cisco Service Contract)