First Published: November 19, 2021

Cisco IP Conference Phone 8832 Release Notes for Firmware Release 14.1(1)

These release notes support the Cisco IP Conference Phone 8832 running SIP Firmware Release 14.1(1).

The following table lists the support compatibility for the Cisco IP Phones.

Table 1. Cisco IP Phones, Support, and Firmware Release Compatibility

Cisco IP Phone

Support Requirements

8832

Cisco Unified Communications Manager 10.5(2) and later

Cisco Unified Communications Manager time zone update 2016d or later

SRST 8.0 (IOS load 15.1(1)T) and above

Cisco Expressway 8.7

8832

Unified CME 12.3 (Cisco IOS XE Fuji 16.9.1 release)

Related Documentation

Use the following sections to obtain related information.

Cisco IP Conference Phone 8832 Documentation

Find documentation specific to your language, phone model, and call control system on the product support page for the Cisco IP Phone 7800 Series.

Cisco Unified Communications Manager Documentation

See the Cisco Unified Communications Manager Documentation Guide and other publications that are specific to your Cisco Unified Communications Manager release on the product support page.

New and Changed Features

The following sections describe the features that are new or have changed in this release.

Features Available with the Firmware Release

The following sections describe the features available with the Firmware Release.

OAuth and Proxy TFTP Security Improvement

OAuth is now supported for Proxy Trivial File Transfer Protocol (TFTP). This feature keeps your phone secure during the registration process.

It requires Cisco Unified Communications Manager Release 14.0(1)SU1 or later.

OAuth Proxy TFTP is not supported for Mobile and Remote Access Through Expressway (MRA).

Where to Find More Information

  • Feature Configuration Guide for Cisco Unified Communications Manager (Release 14.0(1) or later)

  • System Configuration Guide for Cisco Unified Communications Manager (Release 14.0(1) or later)

Improved Call Alert for Hunt Group

Hunt Group has been improved to make it easier to identify calls.

The Call Alert shows Caller ID (when Caller ID is configured), Directory Number and Hunt Group Pilot Number for the hunt group call. The hunt group number is displayed after the label Hunt Group.

Where to Find More Information

Expanded Speed Dial

It is easier to use the following call features because of the softkey Speed Dial:

  • Call transfer

  • Conference calls

  • Group pickup

When you perform one of above call features, you will be able to use a new softkey Speed Dial to go to the speed dial list window you need to dial out. Use the navigation ring to move within the window, and to select your speed dial.

This feature doesn't require any configuration.

Where to Find More Information

  • Cisco IP Phone 8800 Series Administration Guide

  • Cisco IP Phone 8800 Series User Guide

Phone Migration without Transition Load

You can now migrate your enterprise phone to a multiplatform phone firmware in a single step without using transition firmware load, and then obtain and authorize the migration license from the server.

Where to Find More Information

  • Cisco IP Phone 7800 and 8800 Series Migration Guide (On-Premises to Multiplatform Phones)

  • Convert between Enterprise Firmware and Multiplatform Firmware for Cisco IP Phone 7800 and 8800 Series

Installation

Installation Requirements

Before you install the firmware release, you must ensure that your Cisco Unified Communications Manager is running the latest device pack. After you install a device pack on the Cisco Unified Communications Manager servers in the cluster, reboot all the servers.


Warning

The Cisco IP Conference Phone 8832 PoE Injector is supported on phones running firmware release 12.0(1)SR2 and later. Confirm that the latest firmware release is installed on the Cisco Unified Communications Manager before you connect the Cisco IP Conference Phone 8832 with the PoE injector to the network.

If you are not using the latest firmware release, then your phone may downgrade to an earlier firmware release, and lose network connectivity.

Install the Firmware Release on CUCM

Before using the phone firmware release on the Cisco Unified Communications Manager, you must install the latest Cisco Unified Communications Manager firmware on all Cisco Unified Communications Manager servers in the cluster.

Procedure

Step 1

Go to the Software Download page for the Cisco IP Conference Phone 8832
Step 2

Choose your phone model .

Step 3

Choose Session Initiation Protocol (SIP) Software.

Step 4

In the Latest Releases folder, choose 14.1(1).

Step 5

Select the firmware file, click the Download or Add to cart button, and follow the prompts.

The firmware filename is cmterm-8832-sip.14-1-1-0001-125.k4.cop.sha512

Note 

If you added firmware to the cart, when you are ready to download the files, click the Cart and then click Download All.

Step 6

Click the + next to the firmware file name in the Download Cart section to access additional information about this file.

Step 7

Click the Readme link to open the installation instructions for the firmware.
Step 8

Follow the instructions in the readme file to install the firmware.

Install the Firmware Zip Files

If a Cisco Unified Communications Manager is not available to load the installer program, a zip file is available to load the firmware.

Firmware upgrades over the WLAN interface may take longer than upgrades using a wired connection. Upgrade times over the WLAN interface may take more than an hour, depending on the quality and bandwidth of the wireless connection.

Procedure

Step 1

Go to the software download page for the IP Conference Phone 8832
Step 2

Choose your phone model.

Step 3

Choose Session Initiation Protocol (SIP) Software.

Step 4

In the Latest Releases folder, choose 14.1(1).

Step 5

Select the firmware file, click the DownloadDownlod or Add to Cartbutton, and follow the prompts.

The firmware filename is cmterm-8832.14-1-1-0001-125.zip
Step 6

Unzip the files.

Step 7

For information about how to manually copy the firmware files to the server, see the Cisco Unified Communications Operating System Administration Guide

Limitations and Restrictions

Phone Behavior During Times of Network Congestion

  • Administrative tasks, such as an internal port scan or security scan

  • Attacks that occur on your network, such as a Denial of Service attack

Firmware Limitation of Cisco IP Conference Phone 8832 with Cisco IP Conference Phone 8832 PoE Injector

The Cisco IP Conference Phone 8832 PoE Injector is supported on phones running firmware release 12.0(1)SR2 and later. Confirm that the latest firmware release is installed on the Cisco Unified Communications Manager before you connect the Cisco IP Conference Phone 8832 with the PoE injector to the network.

If you are not using the latest firmware release, then your phone may downgrade to an earlier firmware release, and lose the network connectivity.

To recover a phone that has lost network connectivity, update Device Defaults for the Cisco IP Conference Phone 8832 to 8832-sip.12-0-1SR2-2.k3.cop.sgn or later in Cisco Unified Communications Manager Administration. Then, perform one of the following steps:

  • Force the phone to reboot from the alternate software image that supports the PoE Injector. To reboot your phone from the backup image, see Boot Up the Conference Phone from the Alternate Partition section in the Cisco IP Conference Phone 8832 Administration Guide for Cisco Unified Communications Manager.

  • Install and use the Cisco IP Conference Phone 8832 Ethernet Injector on the phone. This allows you to regain network connectivity. After the phone has upgraded to the latest firmware, you can again use the Cisco IP Conference Phone 8832 PoE Injector.

Health-Care Environment Use

This product is not a medical device and uses an unlicensed frequency band that is susceptible to interference from other devices or equipment.

Language Limitation

There is no localized Keyboard Alphanumeric Text Entry (KATE) support for the following Asian locales:

  • Chinese (China)

  • Chinese (Hong Kong)

  • Chinese (Taiwan)

  • Japanese (Japan)

  • Korean (Korea Republic)

The default English (United States) KATE is presented to the user instead.

For example, the phone screen will show text in Korean, but the 2 key on the keypad will display a b c 2 A B C.

Wireless Microphone Battery Limitation

When you press the Show detail softkey, the Cisco IP Conference Phone 8832 occasionally displays a false Bad battery warning. This issue occurs when you quickly reseat the wireless microphone 20 consecutive times or more.

To recover from this issue, perform the following steps in order:

  • Remove the microphone from the charging cradle.

  • Press the Mute button for approximately 10 seconds or until the microphone LED stops blinking white. Then, reseat the microphone on the charging cradle.

  • Restart the phone by disconnecting and reconnecting the Cisco IP Conference Phone 8832 Power Adapter.

    The Bad battery warning on the phone screen disappears and the current battery status appears. If you do not see the battery status, then the microphone battery has deteriorated and you must replace it.

Phone Data Migration Limitation for Cisco Unified Communications Manager Software Release 11.5SU8

The Phone Data Migration feature in Cisco Unified Communications Manager 11.5SU8 is not localized. Parameters and other items may not display in your native language. The limitation does not apply to information displayed on the phones.

Localization is complete for Cisco Unified Communications Manager Software Release 12.5(1)SU3 and later.

Caveats

View Caveats

You can search for caveats using the Cisco Bug Search.

Known caveats (bugs) are graded according to severity level, and can be either open or resolved.

Before you begin

To view caveats, you need the following items:

  • Internet connection

  • Web browser

  • Cisco.com user ID and password

Procedure

Step 1

Perform one of the following actions:

Step 2

When prompted, log in with your Cisco.com user ID and password.

Step 3

(Optional) To look for information about a specific problem, enter the bug ID number in the Search for field, and press Enter.

Open Caveats

The following list contains severity 1, 2, and 3 defects that are open for the Cisco IP Conference Phone 8832 for Firmware Release 14.1(1).

For more information about an individual defect, access the Bug Search toolkit and search for the defect using the Identifier. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, the list reflects a snapshot of the defects that were open at the time this report was compiled. For an updated view of open defects, access Bug Toolkit as described in View Caveats.

  • CSCvq55980 - Network name still displayed ssid when no wifi radio available

Resolved Caveats

The following list contains severity 1, 2, and 3 defects that are resolved for the Cisco IP Conference Phone 8832 for Firmware Release 14.1(1).

For more information about an individual defect, access the Bug Search toolkit and search for the defect using the Identifier. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, the list reflects a snapshot of the defects that were open at the time this report was compiled. For an updated view of open defects, access Bug Toolkit as described in View Caveats.

  • CSCvy08413 HW version on 8832 web page is error

Application Programming Interface

Cisco supports phone API utilization by 3rd party applications that have been tested and certified through Cisco by the 3rd party application developer. Any phone issues related to uncertified application interaction must be addressed by the 3rd party and will not be addressed by Cisco.

For support model of Cisco certified 3rd party applications/solutions, please refer to Cisco Solution Partner Program website for details.

Cisco Unified Communication Manager Public Keys

To improve software integrity protection, public keys are used to sign cop files for Cisco Unified Communications Manager Release 10.0.1 and later. These cop files have "k3 or k4" in their name. To install a k3 or k4 cop file on a pre-10.0.1 Cisco Unified Communications Manager, consult the README for the ciscocm.version3-keys.cop.sgn to determine if you must install this additional cop file on your specific Cisco Unified Communications Manager version. If these keys are not present and are required, you will see the error "The selected file is not valid" when you try to install the software package.

Unified Communications Manager Endpoints Locale Installer

By default, Cisco IP Phones are set up for the English (United States) locale. To use the Cisco IP Phones in other locales, you must install the locale-specific version of the Unified Communications Manager Endpoints Locale Installer on every Cisco Unified Communications Manager server in the cluster. The Locale Installer installs the latest translated text for the phone user interface and country-specific phone tones on your system so that they are available for the Cisco IP Phones.

To access the Locale Installer required for a release, access the Software Download page, navigate to your phone model, and select the Unified Communications Manager Endpoints Locale Installer link.

For more information, see the documentation for your particular Cisco Unified Communications Manager release.


Note

The latest Locale Installer may not be immediately available; continue to check the website for updates.

Cisco IP Phone Documentation Updates on Cisco Unified Communications Manager

The Cisco Unified Communications Manager Self Care Portal (Release 10.0 and later) and User Options web pages (Release 9.1 and earlier) provide links to the IP Phone user guides in PDF format. These user guides are stored on the Cisco Unified Communications Manager and are up to date when the Cisco Unified Communications Manager release is first made available to customers.

After a Cisco Unified Communications Manager release, subsequent updates to the user guides appear only on the Cisco website. The phone firmware release notes contain the applicable documentation URLs. In the web pages, updated documents display "Updated" beside the document link.


Note

The Cisco Unified Communications Manager Device Packages and the Unified Communications Manager Endpoints Locale Installer do not update the English user guides on the Cisco Unified Communications Manager.

You and your users should check the Cisco website for updated user guides and download the PDF files. You can also make the files available to your users on your company website.


Tip

You may want to bookmark the web pages for the phone models that are deployed in your company and send these URLs to your users.