Cisco IP Phone 8800 Series Release Notes for Firmware Release 12.5(1)SR3

These release notes support the Cisco IP Phone 8811, 8841, 8845, 8851, 8851NR, 8861, 8865, and 8865NR running SIP Firmware Release 12.5(1)SR3.

The following table lists the support and protocol compatibility for the Cisco IP Phones.

Table 1. Cisco IP Phones, Support, and Firmware Release Compatibility

Cisco IP Phone

Protocol

Support Requirements

8811, 8841, 8845, 8851, 8851NR, 8861, 8865, and 8865NR

SIP

Cisco Unified Communications Manager 8.5(1) and later

Cisco Unified Communications Manager DST Olsen version D or later

SRST 8.0 (IOS load 15.1(1)T) and above

Cisco Expressway 8.7

8811, 8841, 8851, 8851NR, and 8861

SIP

CME 10.0 (IOS load 15.3(3)M)

Related Documentation

Use the following sections to obtain related information.

New and Changed Features

The following sections describe the features that are new or have changed in this release.


Note

Some features may require the installation of a Cisco Unified Communications Manager Device Package. Failure to install the Device Package before the phone firmware upgrade may render the phones unusable.


Features Available with the Firmware Release

The following sections describe the features available with the Firmware Release.

Cisco Headset Management

You can manage and control your Cisco headsets from a central location on Cisco Unified Communications Manager Administration. You can:

  • Apply customized settings and control default templates

  • Track deployed headsets and to generate inventory reports

You manage the headsets in Cisco Unified Communications Manager Administration with the Device > Headsets page.

This feature requires Cisco Unified Communications Manager 12.5(1)SU1 or later, and Cisco Headset 500 Series Firmware Release 1.5(0) or later to function.

Where to Find More Information
  • Administration Guide for Cisco Unified Communications Manager, Release 12.5(1)SU1

  • Cisco Headset 500 Series Administration Guide

Reset Headset Settings

Users can reset their Cisco Headset 530 Series or Cisco Headset 560 Series headset settings to remove their customizations. The headsets take the settings configured in the user's headset profile, as described in Cisco Headset Management.

The headset must be connected to the phone (USB connector for the Cisco Headset 530; USB connector or Y-cable to the Cisco Headset 560 Standard Base or Multibase). To reset the settings, the user presses Applications and selects Settings > Accessories > Setup > Reset settings.

Where to Find More Information
  • Cisco IP Phone 8800 Series User Guide

  • Cisco IP Phone 7800 and 8800 Series Accessories Guide

Generate a Problem Report Tool Log from Cisco Unified Communications Manager

You can generate a Problem Report Tool (PRT) log for a phone from Cisco Unified Communications Manager Administration. This allows you to collect the phone logs without generating a report from the phone. With this release, headset information is also displayed in the log, which you can use for troubleshooting.

You generate the PRT log in Cisco Unified Communications Manager Administration with the Device > Phone page.

You need to add a server address to the Customer Support Upload URL field on Cisco Unified Communications Manager before you generate the PRT log.

This feature requires Cisco Unified Communications Manager 12.5(1)SU1 or later.

Where to Find More Information
  • Cisco IP Phone 8800 Series Administration Guide for Cisco Unified Communications Manager

Features Available with the Latest Cisco Unified Communications Manager Device Pack

The following sections describe features in the release which require the new firmware and the latest Cisco Unified Communications Manager Device Pack. The applicable device packs are released after the firmware release.

For information about the Cisco Unified IP Phones and the required Cisco Unified Communications Manager device packs, see the following URL:

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/compat/devpack_comp_mtx.html

Activation Code Onboarding for Mobile and Remote Access

You can use Activation Code Onboarding with Mobile and Remote Access when you deploy Cisco IP Phones for off-premises users. This feature is a secure way to deploy off-premises phones when autoregistration is not required. But you can also configure a phone for autoregistration when on-premises, and activation codes when off-premises.

This feature extends the on-premises Activation Code Onboarding feature to off-premises phones.

Activation Code Onboarding for Mobile and Remote Access requires the following to function:

  • Smart Licensing

  • Cisco Expressway X12.5 or later.

  • Cisco Unified Communications Manager 12.5(1)SU1 or later

To enable this feature, you select Allow Activation Code via MRA and Require Activation Code for Onboarding in the Device Information section of the Phone Configuration page.

Where to Find More Information
  • Cisco IP Phone 8800 Series Administration Guide for Cisco Unified Communications Manager

  • Administration Guide for Cisco Unified Communications Manager and IM and Presence Service, Release 12.0(1) or later

Installation

Installation Requirements

Before you install the firmware release, you must ensure that your Cisco Unified Communications Manager (Unified CM) is running the latest device pack. After you install a device pack on the Unified CM servers in the cluster, you need to reboot all the servers.


Note

If your Unified CM doesn't have the required device pack to support this firmware release, the firmware may not work correctly.


For information on the Unified CM Device Packs, see https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/compat/matrix/CMDP_BK_CCBDA741_00_cucm-device-package-compatibility-matrix.html.

Install the Firmware Release on Cisco Unified Communications Manager

Before using the phone firmware release on the Cisco Unified Communications Manager, you must install the latest Cisco Unified Communications Manager firmware on all Cisco Unified Communications Manager servers in the cluster.

Procedure


Step 1

Go to the following URL:

Step 2

Choose Cisco IP Phone 8800 Series.

Step 3

Choose your phone type.

Step 4

Choose Session Initiation Protocol (SIP) Software.

Step 5

In the Latest Releases folder, choose 12.5(1)SR3.

Step 6

Select the firmware file, click the Download or Add to cart button, and follow the prompts:

  • For Cisco IP Phone 8811, 8841, 8851, 8851NR, and 8861—cmterm-88xx-sip.12-5-1SR3-74.k3.cop.sgn

  • For Cisco IP Phone 8845, 8865, and 8865NR—cmterm-8845_65-sip.12-5-1SR3-74.k3.cop.sgn

Note 

If you added the firmware file to the cart, click the Download Cart link when you are ready to download the file.

Step 7

Click the + next to the firmware file name in the Download Cart section to access additional information about this file. The hyperlink for the readme file is in the Additional Information section, which contains installation instructions for the corresponding firmware.

Step 8

Follow the instructions in the readme file to install the firmware.


Install the Firmware Zip Files

If a Cisco Unified Communications Manager is not available to load the installer program, the following .zip files are available to load the firmware.

  • For Cisco IP Phone 8811, 8841, 8851, 8851NR, and 8861—cmterm-88xx.12-5-1SR3-74.zip

  • For Cisco IP Phone 8845, 8865, and 8865NR—cmterm-8845_65.12-5-1SR3-74.zip

Firmware upgrades over the WLAN interface may take longer than upgrades using a wired connection. Upgrade times over the WLAN interface may take more than an hour, depending on the quality and bandwidth of the wireless connection.

Procedure


Step 1

Go to the following URL:

Step 2

Choose Cisco IP Phones 8800 Series.

Step 3

Choose your phone model.

Step 4

Choose Session Initiation Protocol (SIP) Software.

Step 5

In the Latest Releases folder, choose 12.5(1)SR3.

Step 6

Download the relevant zip files.

Step 7

Unzip the files.

Step 8

Manually copy the unzipped files to the directory on the TFTP server. See Cisco Unified Communications Operating System Administration Guide for information about how to manually copy the firmware files to the server.


Limitations and Restrictions

Phone Behavior During Times of Network Congestion

Anything that degrades network performance can affect phone audio and video quality, and in some cases, can cause a call to drop. Sources of network degradation can include, but are not limited to, the following activities:

  • Administrative tasks, such as an internal port scan or security scan

  • Attacks that occur on your network, such as a Denial of Service attack

Health-Care Environment Use

This product is not a medical device and uses an unlicensed frequency band that is susceptible to interference from other devices or equipment.

On-Hook Transfer Limitation in SIP Phones

When the Cisco Unified Communications Manager Transfer On-Hook Enabled field is enabled, users might report a problem with direct call transfer in SIP phones. If the user transfers the call and immediately goes on hook before they hear the ring signal, the call may drop instead of being transferred.

The user needs to hear the ring signal so that they can be sure that the call is being routed.

Ringtone Limitation During Firmware Downgrade from Release 11.5(1)

When the phone downgrades from Firmware Release 11.5(1) to Firmware Release 11.0(1), the phone may not ring when there is an incoming call. The ringtone for the line has been deleted and must be manually set in the Settings > Ringtone menu.

Language Limitation

There is no localized Keyboard Alphanumeric Text Entry (KATE) support for the following Asian locales:

  • Chinese (China)

  • Chinese (Hong Kong)

  • Chinese (Taiwan)

  • Japanese (Japan)

  • Korean (Korea Republic)

The default English (United States) KATE is presented to the user instead.

For example, the phone screen will show text in Korean, but the 2 key on the keypad will display a b c 2 A B C.

Softkey Templates and Video Mode

You can't configure softkey templates for Video mode on the Cisco IP Phone 8800 Series phones. If a softkey appears on the phone, then it will not function correctly.

Caveats

View Caveats

You can search for caveats using the Cisco Bug Search.

Known caveats (bugs) are graded according to severity level, and can be either open or resolved.

Procedure


Step 1

Perform one of the following actions:

Step 2

When prompted, log in with your Cisco.com user ID and password.

Step 3

(Optional) Enter the bug ID number in the Search for field, then press Enter.


Open Caveats

The following list contains severity 1, 2, and 3 defects that are open for the Cisco IP Phone 8800 Series for Firmware Release 12.5(1)SR3.

For more information about an individual defect, access the Bug Search toolkit and search for the defect using the Identifier. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, the list reflects a snapshot of the defects that were open at the time this report was compiled. For an updated view of open defects, access Bug Toolkit as described in View Caveats.

  • CSCvi43560: After ADA incoming call announcement, ringer is played from BT headset, not speaker

  • CSCvn16712: 88xx phone LEDs flash due to MIC keys being overwritten

  • CSCvp72972: Display (Caller ID) and RIU(Remote) are overlapped

Resolved Caveats

The following list contains the severity 1, 2, and 3 defects that are resolved for the Cisco IP Phone 8800 Series that uses Firmware Release 12.5(1)SR3.

For more information about an individual defect, you can access the online record for the defect from the Bug Search Toolkit. You must be a registered Cisco.com user to access this online information.

Because defect status continually changes, the list reflects a snapshot of the defects that were open at the time this report was compiled. For an updated view of resolved defects or to view specific bugs, access the Bug Search Toolkit as described in View Caveats.

  • CSCvm21280: Evaluation of sl-bigeasy-phones for CVE-2018-5391 (FragmentSmack)

  • CSCvn97460: 8861 restarts when accessing the call history screen due to Java running out of memory

  • CSCvo04442: 88XX phones use incorrect line to make a call with shared line

  • CSCvo76607: Phone doesn't adhere to RFC3711 while sending SRTPC BYE message

  • CSCvo76995: 8861 KEM Remote Line in use LED displays wrong color in specific scenario

  • CSCvo98362: "Error:Invalid Code in Speed dial" not displayed if FAC or CMC is misconfigured

  • CSCvp03879: 8865 with APU72 USB adapter, call is dropped when initiating a conference call

  • CSCvp13743: Phone does not display Called Party Name when second digit of Called Party Number is either 4 or 5

  • CSCvp14154: Plug-out and plug-in headset's APU71 USB adapter cable from the phone during call results in no audio

  • CSCvp25014: Remote party resume the call will change the focus of the share line's to the first line.

  • CSCvp26442: 88xx: Second line seizes focus with ELM enabled and "Always use prime line" disabled

  • CSCvp28297: the focus can not shift to the first line when use the same phone line making two calls

  • CSCvp28359: Local ringing does not stop when Early media packets are received

  • CSCvp43504: phone dn disappear and show incorrectly when press setup softkey under accessories page.

  • CSCvp46043: 8861 showing Restricted / SIP URI when call answered and held

  • CSCvp61074: IPPhoneExecute ignores comma in dial executeItem on phone models 8851/65

  • CSCvp62731: BT battary and signal icon should be right aligned in R2L locale

  • CSCvp69871: 78xx media server may crash when sending buffered pre recording packets

  • CSCvp87772: IP Phone 8851 will reset when using Headset 562 and Using USB ONLY

Cisco Unified Communication Manager Public Keys

To improve software integrity protection, new public keys are used to sign cop files for Cisco Unified Communications Manager Release 10.0.1 and later. These cop files have "k3" in their name. To install a k3 cop file on a pre-10.0.1 Cisco Unified Communications Manager, consult the README for the ciscocm.version3-keys.cop.sgn to determine if this additional cop file must first be installed on your specific Cisco Unified Communications Manager version. If these keys are not present and are required, you will see the error "The selected file is not valid" when you try to install the software package.

Unified Communications Manager Endpoints Locale Installer

By default, Cisco IP Phones are set up for the English (United States) locale. To use the Cisco IP Phones in other locales, you must install the locale-specific version of the Unified Communications Manager Endpoints Locale Installer on every Cisco Unified Communications Manager server in the cluster. The Locale Installer installs the latest translated text for the phone user interface and country-specific phone tones on your system so that they are available for the Cisco IP Phones.

To access the Locale Installer required for a release, access https://software.cisco.com/download/navigator.html?mdfid=286037605&flowid=46245, navigate to your phone model, and select the Unified Communications Manager Endpoints Locale Installer link.

For more information, see the documentation for your particular Cisco Unified Communications Manager release.


Note

The latest Locale Installer may not be immediately available; continue to check the website for updates.


Cisco IP Phone Documentation Updates on Cisco Unified Communications Manager

The Cisco Unified Communications Manager Self Care Portal (Release 10.0 and later) and User Options web pages (Release 9.1 and earlier) provide links to the IP Phone user guides in PDF format. These user guides are stored on the Cisco Unified Communications Manager and are up to date when the Cisco Unified Communications Manager release is first made available to customers.

After a Cisco Unified Communications Manager release, subsequent updates to the user guides appear only on the Cisco website. The phone firmware release notes contain the applicable documentation URLs. In the web pages, updated documents display "Updated" beside the document link.


Note

The Cisco Unified Communications Manager Device Packages and the Unified Communications Manager Endpoints Locale Installer do not update the English user guides on the Cisco Unified Communications Manager.


You and your users should check the Cisco website for updated user guides and download the PDF files. You can also make the files available to your users on your company website.


Tip

You may want to bookmark the web pages for the phone models that are deployed in your company and send these URLs to your users.