Cisco IE 1000 Industrial Ethernet Switch Hardware Installation Guide

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents

Find Matches in This Book

Available Languages

Download Options

Book Title

Cisco IE 1000 Industrial Ethernet Switch Hardware Installation Guide

Chapter Title

Technical Specifications

PDF - Complete Book (4.15 MB)
View with Adobe Reader on a variety of devices

Results

Updated:: November 19, 2021

Technical Specifications

This appendix provides the technical specification for the Cisco IE 1000 switches.

Operating Temperature Specifications

Table 1 lists the Operating Temperatures (measured inside enclosure, 1” below switch) for the Cisco IE 1000 switches.

Table 1 Operation Temperature Specification for the Cisco IE 1000 Switches
	Industrial Automation and Hazardous Locations	Substation	Traffic Signal
Enclosure types	Sealed enclosures (No airflow) For example: NEMA4, NEMA4X, NEMA12, NEMA13, IP54, and IP66.	Vented enclosures (Minimum 40 lfm¹) For example: NEMA1, IP20, and IP21.	Fan or blower-equipped enclosures (Minimum 200 lfm)
Temperatures (measured inside enclosure, 1” below switch)	POE: -40C to +60C Non-POE: -20C to +60C	POE: -40C to +70C Non-POE: -20C to +70C	POE: -34C to +74C Non-POE: -16C to +74C

^1.lfm = linear feet per minute.

Note: The safety certifications apply only to ambient temperatures under 158°F (70°C) measured 1” below switch. However, the Cisco IE 1000 switch can function under the environmental conditions shown in Table 1.

Technical Specifications

The technical specifications for the Cisco IE 1000 switches are as follows:

Table 2 Cisco IE 1000 Technical Specifications


Environmental Ranges
Storage temperature	–40 to 185°F (–40 to 85°C)
Operating temperature ² (Measured inside enclosure, 1” below switch)	POE	Non-POE
	-34C to +74C ■ -40C to +70C (40 lfm Vented Enclosure Operating) ■ -40C to +60C (Sealed Enclosure Operating) ■ -34C to +74C (Minimum 200 lfm Fan or Blower equipped Enclosure Operating) -40C to +85C (Type Tested to +85C for 16 hours) ³	-16C to +74C ■ -20C to +70C (40 lfm Vented Enclosure Operating) ■ -20C to +60C (Sealed Enclosure Operating) ■ -16C to +74C (Minimum 200 lfm Fan or Blower equipped Enclosure Operating) 85C Type Tested for 16 hours
Operating humidity	5 to 95% (noncondensing)
Operating shock	30 g at 11 ms, and 200 g at 2.11 ms.
Operating altitude	Up to 13,000 ft (3962 m)
Storage altitude	Up to 40,000 ft (12,192 m)
Power Requirements
DC input voltage	■ Marked range: – 12-24 VDC (IE1000-4T1T / IE1000-6T2T) – 48-54 VDC (IE1000-4P2S / IE1000-8P2S) ■ Maximum operating range: – 9-32 VDC (IE1000-4T1T / IE1000-6T2T) – 48-54 VDC (IE1000-4P2S / IE1000-8P2S) Note: ■ The DC-input power supply is an SELV circuit, and it can only be connected to another SELV circuit.
Power consumption	■ IE-1000-4T1T-LM -- 3.6W ■ IE-1000-6T2T-LM -- 4.8W ■ IE-1000-4P2S-LM -- 140.4W ■ IE-1000-8P2S-LM -- 205.2W


Physical Dimensions
Weight	IE-1000-4T1T-LM -- 1.10 lb (0.50 kg) IE-1000-6T2T-LM -- 1.25 lb (0.57 kg) IE-1000-4P2S-LM -- 1.70 lb (0.77 kg) IE-1000-8P2S-LM -- 1.85 lb (0.84 kg)
Dimensions (W x D x H).8 x 5.3 x 5 in. (45.7 x 134 x 127 mm)⁴	IE-1000-4T1T-LM -- 1.5 x 4.5 x 5 in. (38.1 x 115 x 127 mm) IE-1000-6T2T-LM -- 1.8 x 4.5 x 5 in. (45.7 x 115 x 127 mm) IE-1000-4P2S-LM -- 1.8 x 5.3 x 5 in. (45.7 x 134 x 127 mm) IE-1000-8P2S-LM -- 1

^2.Operating temperatures exceeding 60C are not covered by the product safety certifications and approvals. However, the switch can function in the installations under the environmental conditions listed.

^3.When using industrial grade SFP modules, maximum operating temperature limits shown in table 1 apply. When using commercial grade SFP modules, maximum system operating temperature limits must be de-rated by 15 deg. C.

^4.Width includes the cosmetic end-caps. Height does not include the power and alarm connections.

Alarm Ratings

The alarm ratings for the Cisco IE 1000 switches are below.

Table 3 Cisco IE 1000 Alarm Ratings
Alarm Ratings	Specification
Alarm output electrical specification	1.0 A @ 24 VDC or 0.5 A @ 48 VDC

Was this Document Helpful?

Feedback

Contact Cisco

Open a Support Case
(Requires a Cisco Service Contract)