- Index
- Preface
- Overview
- Using the Command-Line Interface
- Clustering Switches
- Assigning the Switch IP Address and Default Gateway
- Configuring Cisco IOS Configuration Engine
- Managing Switch Stacks
- Administering the Switch
- Configuring SDM Templates
- Configuring Switch-Based Authentication
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring Web-Based Authentication
- Configuring Interface Characteristics
- Configuring VLANs
- Configuring VTP
- Configuring Voice VLAN
- Configuring Private VLANs
- Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling
- Configuring STP
- Configuring MSTP
- Configuring Optional Spanning-Tree Features
- Configuring Flex Links and the MAC Address-Table Move Update Feature
- Configuring DHCP Features and IP Source Guard
- Configuring Dynamic ARP Inspection
- Configuring IGMP Snooping and MVR
- Configuring Port-Based Traffic Control
- Configuring CDP
- Configuring LLDP, LLDP-MED, and Wired Location Service
- Configuring UDLD
- Configuring SPAN and RSPAN
- Configuring RMON
- Configuring System Message Logging
- Configuring SNMP
- Configuring Embedded Event Manager
- Configuring Network Security with ACLs
- Configuring QoS
- Configuring EtherChannels and Link-State Tracking
- Configuring TelePresence E911 IP Phone Support
- Configuring IP Unicast Routing
- Configuring IPv6 Routing
- Configuring IPv6 MLD Snooping
- Configuring IPv6 ACLs
- Configuring HSRP
- Configuring Cisco IOS IP SLAs Operations
- Configuring Enhanced Object Tracking
- Configuring IP Multicast Routing
- Configuring MSDP
- Configuring Cache Services By Using WCCP
- Configuring Fallback Bridging
- Troubleshooting
- Configuring Online Diagnostics
- Configuring the Catalyst 3750G Integrated Wireless LAN Controller Switch
- Supported MIBs
- Working with the Cisco IOS File System, Configuration Files, and Software Images
- Unsupported Commands in Cisco IOS Release 12.2(55)SE
- Working with the Flash File System
- Displaying Available File Systems
- Setting the Default File System
- Displaying Information about Files on a File System
- Changing Directories and Displaying the Working Directory
- Creating and Removing Directories
- Copying Files
- Deleting Files
- Creating, Displaying, and Extracting tar Files
- Displaying the Contents of a File
- Working with Configuration Files
- Guidelines for Creating and Using Configuration Files
- Configuration File Types and Location n
- Creating a Configuration File By Using a Text Editor
- Copying Configuration Files By Using TFTP
- Copying Configuration Files By Using FTP
- Copying Configuration Files By Using RCP
- Clearing Configuration Information
- Replacing and Rolling Back Configurations
Working with the Cisco IOS File System, Configuration Files, and Software Images
This appendix describes how to manipulate the Catalyst 3750 switch flash file system, how to copy configuration files, and how to archive (upload and download) software images to a switch. Unless otherwise noted, the term switch refers to a standalone switch and to a switch stack.
Note For complete syntax and usage information for the commands used in this chapter, see the switch command reference for this release and the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2 from the Cisco.com page under Documentation > Cisco IOS Software > 12.2 Mainline > Command References.
Working with the Flash File System
The flash file system is a single flash device on which you can store files. It also provides several commands to help you manage software image and configuration files. The default flash file system on the switch is named flash:.
As viewed from the stack master, or any stack member, flash: refers to the local flash device, which is the device attached to the same switch on which the file system is being viewed. In a switch stack, each of the flash devices from the various stack members can be viewed from the stack master. The names of these flash file systems include the corresponding switch member numbers. For example, flash3:, as viewed from the stack master, refers to the same file system as does flash: on stack member 3. Use the show file systems privileged EXEC command to list all file systems, including the flash file systems in the switch stack.
No more than one user at a time can manage the software images and configuration files for a switch stack.
These sections contain this configuration information:
- Displaying Available File Systems
- Displaying Information about Files on a File System
- Creating and Removing Directories
- Copying Files
- Deleting Files
- Creating, Displaying, and Extracting tar Files
- Displaying the Contents of a File
Displaying Available File Systems
To display the available file systems on your switch, use the show file systems privileged EXEC command as shown in this example. In this example, the stack master is stack member 3; therefore flash3:
is aliased to flash:
. The file system on stack member 5 is displayed as flash5
on the stack master.
Setting the Default File System
You can specify the file system or directory that the system uses as the default file system by using the cd filesystem: privileged EXEC command. You can set the default file system to omit the filesystem: argument from related commands. For example, for all privileged EXEC commands that have the optional filesystem: argument, the system uses the file system specified by the cd command.
By default, the default file system is flash:.
You can display the current default file system as specified by the cd command by using the pwd privileged EXEC command.
Displaying Information about Files on a File System
You can view a list of the contents of a file system before manipulating its contents. For example, before copying a new configuration file to flash memory, you might want to verify that the file system does not already contain a configuration file with the same name. Similarly, before copying a flash configuration file to another location, you might want to verify its filename for use in another command.
To display information about files on a file system, use one of the privileged EXEC commands in Table C-2 :
Changing Directories and Displaying the Working Directory
Beginning in privileged EXEC mode, follow these steps to change directories and display the working directory.
Creating and Removing Directories
Beginning in privileged EXEC mode, follow these steps to create and remove a directory:
To delete a directory with all its files and subdirectories, use the delete /force /recursive filesystem :/ file-url privileged EXEC command.
Use the /recursive keyword to delete the named directory and all subdirectories and the files contained in it. Use the /force keyword to suppress the prompting that confirms a deletion of each file in the directory. You are prompted only once at the beginning of this deletion process. Use the /force and /recursive keywords for deleting old software images that were installed by using the archive download-sw command but are no longer needed.
For filesystem, use flash: for the system board flash device. For file-url, enter the name of the directory to be deleted. All the files in the directory and the directory are removed.
Copying Files
To copy a file from a source to a destination, use the copy source-url destination-url privileged EXEC command. For the source and destination URLs, you can use running-config and startup-config keyword shortcuts. For example, the copy running-config startup-config command saves the currently running configuration file to the NVRAM section of flash memory to be used as the configuration during system initialization.
You can also copy from special file systems (xmodem:, ymodem:) as the source for the file from a network machine that uses the Xmodem or Ymodem protocol.
Network file system URLs include ftp:, rcp:, and tftp: and have these syntaxes:
- FTP— ftp: [[ // username [ : password ] @ location ] / directory ] / filename
- RCP— rcp: [[ // username @ location ] / directory ] / filename
- TFTP— tftp: [[ // location ] / directory ] / filename
Local writable file systems include flash:.
Some invalid combinations of source and destination exist. Specifically, you cannot copy these combinations:
- From a running configuration to a running configuration
- From a startup configuration to a startup configuration
- From a device to the same device (for example, the copy flash: flash: command is invalid)
For specific examples of using the copy command with configuration files, see the “Working with Configuration Files” section.
To copy software images either by downloading a new version or by uploading the existing one, use the archive download-sw or the archive upload-sw privileged EXEC command. For more information, see the “Working with Software Images” section.
Deleting Files
When you no longer need a file on a flash memory device, you can permanently delete it. To delete a file or directory from a specified flash device, use the delete [ /force ] [ /recursive ] [ filesystem : ] / file-url privileged EXEC command.
Use the /recursive keyword for deleting a directory and all subdirectories and the files contained in it. Use the /force keyword to suppress the prompting that confirms a deletion of each file in the directory. You are prompted only once at the beginning of this deletion process. Use the /force and /recursive keywords for deleting old software images that were installed by using the archive download-sw command but are no longer needed.
If you omit the filesystem : option, the switch uses the default device specified by the cd command. For file-url, you specify the path (directory) and the name of the file to be deleted.
When you attempt to delete any files, the system prompts you to confirm the deletion.
This example shows how to delete the file myconfig from the default flash memory device:
Creating, Displaying, and Extracting tar Files
You can create a tar file and write files into it, list the files in a tar file, and extract the files from a tar file as described in the next sections.
Note Instead of using the copy privileged EXEC command or the archive tar privileged EXEC command, we recommend using the archive download-sw and archive upload-sw privileged EXEC commands to download and upload software image files. For switch stacks, the archive download-sw and archive upload-sw privileged EXEC commands can only be used through the stack master. Software images downloaded to the stack master are automatically downloaded to the rest of the stack members.
To upgrade a switch with an incompatible software image, use the archive copy-sw privileged EXEC command to copy the software image from an existing stack member to the incompatible switch. That switch automatically reloads and joins the stack as a fully functioning member.
Creating a tar File
To create a tar file and write files into it, use this privileged EXEC command:
archive tar /create destination-url flash:/ file-url
For destination-url, specify the destination URL alias for the local or network file system and the name of the tar file to create. These options are supported:
- For the local flash file system, the syntax is
flash: - For the FTP, the syntax is
ftp: [[ // username [ : password ] @ location ] / directory] / tar-filename .tar - For the RCP, the syntax is
rcp: [[ // username @ location ] / directory ] / tar-filename .tar - For the TFTP, the syntax is
tftp: [[ // location ] / directory ] / tar-filename .tar
The tar-filename .tar is the tar file to be created.
For flash:/ file-url, specify the location on the local flash file system from which the new tar file is created. You can also specify an optional list of files or directories within the source directory to write to the new tar file. If none are specified, all files and directories at this level are written to the newly created tar file.
This example shows how to create a tar file. This command writes the contents of the new-configs directory on the local flash device to a file named saved.tar on the TFTP server at 172.20.10.30:
Displaying the Contents of a tar File
To display the contents of a tar file on the screen, use this privileged EXEC command:
For source-url, specify the source URL alias for the local or network file system. These options are supported:
- For the local flash file system, the syntax is
flash: - For the FTP, the syntax is
ftp: [[ // username [ : password ] @ location ] / directory ] / tar-filename .tar - For the RCP, the syntax is
rcp: [[ // username @ location ] / directory ] / tar-filename .tar - For the TFTP, the syntax is
tftp: [[ // location ] / directory ] / tar-filename .tar
The tar-filename .tar is the tar file to display.
You can also limit the display of the files by specifying an optional list of files or directories after the tar file; then only those files appear. If none are specified, all files and directories appear.
This example shows how to display the contents of a switch tar file that is in flash memory:
This example shows how to display only the /html directory and its contents:
/html
Extracting a tar File
To extract a tar file into a directory on the flash file system, use this privileged EXEC command:
archive tar /xtract source-url flash:/ file-url [ dir/file ...]
For source-url, specify the source URL alias for the local file system. These options are supported:
- For the local flash file system, the syntax is
flash: - For the FTP, the syntax is
ftp: [[ // username [ : password ] @ location ] / directory ] / tar-filename .tar - For the RCP, the syntax is
rcp: [[ // username @ location ] / directory ] / tar-filename .tar - For the TFTP, the syntax is
tftp: [[ // location ] / directory ] / tar-filename .tar
The tar-filename .tar is the tar file from which to extract files.
For flash:/ file-url [ dir/file ...], specify t he location on the local flash file system into which the tar file is extracted. Use the dir/file... option to specify an optional list of files or directories within the tar file to be extracted. If none are specified, all files and directories are extracted.
This example shows how to extract the contents of a tar file located on the TFTP server at 172.20.10.30. This command extracts just the new-configs directory into the root directory on the local flash file system. The remaining files in the saved.tar file are ignored.
Displaying the Contents of a File
To display the contents of any readable file, including a file on a remote file system, use the more [ /ascii | /binary | /ebcdic ] file-url privileged EXEC command:.
This example shows how to display the contents of a configuration file on a TFTP server:
Working with Configuration Files
This section describes how to create, load, and maintain configuration files.
Note For information about configuration files in switch stacks, see the “Stack Configuration Files” section.
Configuration files contain commands entered to customize the function of the Cisco IOS software. A way to create a basic configuration file is to use the setup program or to enter the setup privileged EXEC command. For more information, see Chapter3, “Assigning the Switch IP Address and Default Gateway”
You can copy ( download) configuration files from a TFTP, FTP, or RCP server to the running configuration or startup configuration of the switch. You might want to perform this for one of these reasons:
- To restore a backed-up configuration file.
- To use the configuration file for another switch. For example, you might add another switch to your network and want it to have a configuration similar to the original switch. By copying the file to the new switch, you can change the relevant parts rather than recreating the whole file.
- To load the same configuration commands on all the switches in your network so that all the switches have similar configurations.
You can copy ( upload) configuration files from the switch to a file server by using TFTP, FTP, or RCP. You might perform this task to back up a current configuration file to a server before changing its contents so that you can later restore the original configuration file from the server.
The protocol you use depends on which type of server you are using. The FTP and RCP transport mechanisms provide faster performance and more reliable delivery of data than TFTP. These improvements are possible because FTP and RCP are built on and use the TCP/IP stack, which is connection-oriented.
These sections contain this configuration information:
- Guidelines for Creating and Using Configuration Files
- Configuration File Types and Location n
- Creating a Configuration File By Using a Text Editor
- Copying Configuration Files By Using TFTP
- Copying Configuration Files By Using FTP
- Copying Configuration Files By Using RCP
- Clearing Configuration Information
- Replacing and Rolling Back Configurations
Guidelines for Creating and Using Configuration Files
Creating configuration files can aid in your switch configuration. Configuration files can contain some or all of the commands needed to configure one or more switches. For example, you might want to download the same configuration file to several switches that have the same hardware configuration.
Use these guidelines when creating a configuration file:
- We recommend that you connect through the console port for the initial configuration of the switch. If you are accessing the switch through a network connection instead of through a direct connection to the console port, keep in mind that some configuration changes (such as changing the switch IP address or disabling ports) can cause a loss of connectivity to the switch.
- If no password has been set on the switch, we recommend that you set one by using the enable secret secret-password global configuration command.
Note The copy {ftp: | rcp: | tftp:} system:running-config privileged EXEC command loads the configuration files on the switch as if you were entering the commands at the command line. The switch does not erase the existing running configuration before adding the commands. If a command in the copied configuration file replaces a command in the existing configuration file, the existing command is erased. For example, if the copied configuration file contains a different IP address in a particular command than the existing configuration, the IP address in the copied configuration is used. However, some commands in the existing configuration might not be replaced or negated. In this case, the resulting configuration file is a mixture of the existing configuration file and the copied configuration file, with the copied configuration file having precedence.
To restore a configuration file to an exact copy of a file stored on a server, copy the configuration file directly to the startup configuration (by using the copy {ftp: | rcp: | tftp:} nvram:startup-config privileged EXEC command), and reload the switch.
Configuration File Types and Location n
Startup configuration files are used during system startup to configure the software. Running configuration files contain the current configuration of the software. The two configuration files can be different. For example, you might want to change the configuration for a short time period rather than permanently. In this case, you would change the running configuration but not save the configuration by using the copy running-config startup-config privileged EXEC command.
The running configuration is saved in DRAM; the startup configuration is stored in the NVRAM section of flash memory.
Creating a Configuration File By Using a Text Editor
When creating a configuration file, you must list commands logically so that the system can respond appropriately. This is one method of creating a configuration file:
Step 1 Copy an existing configuration from a switch to a server.
For more information, see the “Downloading the Configuration File By Using TFTP” section, the “Downloading a Configuration File By Using FTP” section, or the “Downloading a Configuration File By Using RCP” section.
Step 2 Open the configuration file in a text editor, such as vi or emacs on UNIX or Notepad on a PC.
Step 3 Extract the portion of the configuration file with the desired commands, and save it in a new file.
Step 4 Copy the configuration file to the appropriate server location. For example, copy the file to the TFTP directory on the workstation (usually / tftpboot on a UNIX workstation).
Step 5 Make sure the permissions on the file are set to world-read.
Copying Configuration Files By Using TFTP
You can configure the switch by using configuration files you create, download from another switch, or download from a TFTP server. You can copy (upload) configuration files to a TFTP server for storage.
Preparing to Download or Upload a Configuration File B y Using TFTP
Before you begin downloading or uploading a configuration file by using TFTP, do these tasks:
- Ensure that the workstation acting as the TFTP server is properly configured. On a Sun workstation, make sure that the /etc/inetd.conf file contains this line:
Make sure that the /etc/services file contains this line:
Note You must restart the inetd daemon after modifying the /etc/inetd.conf and /etc/services files. To restart the daemon, either stop the inetd process and restart it, or enter a fastboot command (on the SunOS 4.x) or a reboot command (on Solaris 2.x or SunOS 5.x). For more information on the TFTP daemon, see the documentation for your workstation.
- Ensure that the switch has a route to the TFTP server. The switch and the TFTP server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the TFTP server by using the ping command.
- Ensure that the configuration file to be downloaded is in the correct directory on the TFTP server (usually / tftpboot on a UNIX workstation).
- For download operations, ensure that the permissions on the file are set correctly. The permission on the file should be world-read.
- Before uploading the configuration file, you might need to create an empty file on the TFTP server. To create an empty file, enter the touch filename command, where filename is the name of the file you will use when uploading it to the server.
- During upload operations, if you are overwriting an existing file (including an empty file, if you had to create one) on the server, ensure that the permissions on the file are set correctly. Permissions on the file should be world-write.
Downloading the Configuration File By Using TFTP
To configure the switch by using a configuration file downloaded from a TFTP server, follow these steps:
Step 1 Copy the configuration file to the appropriate TFTP directory on the workstation.
Step 2 Verify that the TFTP server is properly configured by referring to the “Preparing to Download or Upload a Configuration File B y Using TFTP” section.
Step 3 Log into the switch through the console port or a Telnet session.
Step 4 Download the configuration file from the TFTP server to configure the switch.
Specify the IP address or hostname of the TFTP server and the name of the file to download.
Use one of these privileged EXEC commands:
- copy tftp: [[[ // location ] / directory ] / filename ] system:running-config
- copy tftp: [[[ // location ] / directory ] / filename ] nvram:startup-config
The configuration file downloads, and the commands are executed as the file is parsed line-by-line.
This example shows how to configure the software from the file tokyo-confg at IP address 172.16.2.155:
Uploading the Configuration File By Using TFTP
To upload a configuration file from a switch to a TFTP server for storage, follow these steps:
Step 1 Verify that the TFTP server is properly configured by referring to the “Preparing to Download or Upload a Configuration File B y Using TFTP” section.
Step 2 Log into the switch through the console port or a Telnet session.
Step 3 Upload the switch configuration to the TFTP server. Specify the IP address or hostname of the TFTP server and the destination filename.
Use one of these privileged EXEC commands:
- copy system:running-config tftp: [[[ // location ] / directory ] / filename ]
- copy nvram:startup-config tftp: [[[ // location ] / directory ] / filename ]
The file is uploaded to the TFTP server.
This example shows how to upload a configuration file from a switch to a TFTP server:
Copying Configuration Files By Using FTP
You can copy configuration files to or from an FTP server.
The FTP protocol requires a client to send a remote username and password on each FTP request to a server. When you copy a configuration file from the switch to a server by using FTP, the Cisco IOS software sends the first valid username in this list:
- The username specified in the copy command if a username is specified.
- The username set by the ip ftp username username global configuration command if the command is configured.
- Anonymous.
The switch sends the first valid password in this list:
- The password specified in the copy command if a password is specified.
- The password set by the ip ftp password password global configuration command if the command is configured.
- The switch forms a password named username@switchname.domain. The variable username is the username associated with the current session, switchname is the configured hostname, and domain is the domain of the switch.
The username and password must be associated with an account on the FTP server. If you are writing to the server, the FTP server must be properly configured to accept your FTP write request.
Use the ip ftp username and ip ftp password commands to specify a username and password for all copies. Include the username in the copy command if you want to specify only a username for that copy operation.
If the server has a directory structure, the configuration file is written to or copied from the directory associated with the username on the server. For example, if the configuration file resides in the home directory of a user on the server, specify that user's name as the remote username.
For more information, see the documentation for your FTP server.
Preparing to Download or Upload a Configuration File By Using FTP
Before you begin downloading or uploading a configuration file by using FTP, do these tasks:
- Ensure that the switch has a route to the FTP server. The switch and the FTP server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the FTP server by using the ping command.
- If you are accessing the switch through the console or a Telnet session and you do not have a valid username, make sure that the current FTP username is the one that you want to use for the FTP download. You can enter the show users privileged EXEC command to view the valid username. If you do not want to use this username, create a new FTP username by using the ip ftp username username global configuration command during all copy operations. The new username is stored in NVRAM. If you are accessing the switch through a Telnet session and you have a valid username, this username is used, and you do not need to set the FTP username. Include the username in the copy command if you want to specify a username for only that copy operation.
- When you upload a configuration file to the FTP server, it must be properly configured to accept the write request from the user on the switch.
For more information, see the documentation for your FTP server.
Downloading a Configuration File By Using FTP
Beginning in privileged EXEC mode, follow these steps to download a configuration file by using FTP:
|
|
|
---|---|---|
Verify that the FTP server is properly configured by referring to the “Preparing to Download or Upload a Configuration File By Using FTP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode on the switch. This step is required only if you override the default remote username or password (see Steps 4, 5, and 6). |
||
copy ftp: [[[ // [ username [ : password ] @ ] location ] / directory ] / filename ] system:running-config copy ftp: [[[ // [ username [ : password ] @ ] location ] / directory ] / filename ] nvram:startup-config |
Using FTP, copy the configuration file from a network server to the running configuration or to the startup configuration file. |
This example shows how to copy a configuration file named host1-confg from the netadmin1 directory on the remote server with an IP address of 172.16.101.101 and to load and run those commands on the switch:
This example shows how to specify a remote username of netadmin1. The software copies the configuration file host2-confg from the netadmin1 directory on the remote server with an IP address of 172.16.101.101 to the switch startup configuration.
Uploading a Configuration File By Using FTP
Beginning in privileged EXEC mode, follow these steps to upload a configuration file by using FTP:
|
|
|
---|---|---|
Verify that the FTP server is properly configured by referring to the “Preparing to Download or Upload a Configuration File By Using FTP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode. This step is required only if you override the default remote username or password (see Steps 4, 5, and 6). |
||
copy system:running-config ftp: [[[ // [ username [ : password ] @ ] location ] / directory ] / filename ] copy nvram:startup-config ftp: [[[ // [ username [ : password ] @ ] location ] / directory ] / filename ] |
Using FTP, store the switch running or startup configuration file to the specified location. |
This example shows how to copy the running configuration file named switch2-confg to the netadmin1 directory on the remote host with an IP address of 172.16.101.101:
This example shows how to store a startup configuration file on a server by using FTP to copy the file:
Copying Configuration Files By Using RCP
The RCP provides another method of downloading, uploading, and copying configuration files between remote hosts and the switch. Unlike TFTP, which uses User Datagram Protocol (UDP), a connectionless protocol, RCP uses TCP, which is connection-oriented.
To use RCP to copy files, the server from or to which you will be copying files must support RCP. The RCP copy commands rely on the rsh server (or daemon) on the remote system. To copy files by using RCP, you do not need to create a server for file distribution as you do with TFTP. You only need to have access to a server that supports the remote shell (rsh). (Most UNIX systems support rsh.) Because you are copying a file from one place to another, you must have read permission on the source file and write permission on the destination file. If the destination file does not exist, RCP creates it for you.
The RCP requires a client to send a remote username with each RCP request to a server. When you copy a configuration file from the switch to a server, the Cisco IOS software sends the first valid username in this list:
- The username specified in the copy command if a username is specified.
- The username set by the ip rcmd remote-username username global configuration command if the command is configured.
- The remote username associated with the current TTY (terminal) process. For example, if the user is connected to the router through Telnet and was authenticated through the username command, the switch software sends the Telnet username as the remote username.
- The switch hostname.
For a successful RCP copy request, you must define an account on the network server for the remote username. If the server has a directory structure, the configuration file is written to or copied from the directory associated with the remote username on the server. For example, if the configuration file is in the home directory of a user on the server, specify that user's name as the remote username.
Preparing to Download or Upload a Configuration File By Using RCP
Before you begin downloading or uploading a configuration file by using RCP, do these tasks:
- Ensure that the workstation acting as the RCP server supports the remote shell (rsh).
- Ensure that the switch has a route to the RCP server. The switch and the server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the RCP server by using the ping command.
- If you are accessing the switch through the console or a Telnet session and you do not have a valid username, make sure that the current RCP username is the one that you want to use for the RCP download. You can enter the show users privileged EXEC command to view the valid username. If you do not want to use this username, create a new RCP username by using the ip rcmd remote-username username global configuration command to be used during all copy operations. The new username is stored in NVRAM. If you are accessing the switch through a Telnet session and you have a valid username, this username is used, and you do not need to set the RCP username. Include the username in the copy command if you want to specify a username for only that copy operation.
- When you upload a file to the RCP server, it must be properly configured to accept the RCP write request from the user on the switch. For UNIX systems, you must add an entry to the.rhosts file for the remote user on the RCP server. For example, suppose that the switch contains these configuration lines:
If the switch IP address translates to Switch1.company.com, the.rhosts file for User0 on the RCP server should contain this line:
For more information, see the documentation for your RCP server.
Downloading a Configuration File By Using RCP
Beginning in privileged EXEC mode, follow these steps to download a configuration file by using RCP:
|
|
|
---|---|---|
Verify that the RCP server is properly configured by referring to the “Preparing to Download or Upload a Configuration File By Using RCP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode. This step is required only if you override the default remote username (see Steps 4 and 5). |
||
copy rcp: [[[ // [ username @ ] location ] / directory ] / filename ] system:running-config copy rcp: [[[ // [ username @ ] location ] / directory ] / filename ] nvram:startup-config |
Using RCP, copy the configuration file from a network server to the running configuration or to the startup configuration file. |
This example shows how to copy a configuration file named host1-confg from the netadmin1 directory on the remote server with an IP address of 172.16.101.101 and load and run those commands on the switch:
This example shows how to specify a remote username of netadmin1. Then it copies the configuration file host2-confg from the netadmin1 directory on the remote server with an IP address of 172.16.101.101 to the startup configuration:
Uploading a Configuration File By Using RCP
Beginning in privileged EXEC mode, follow these steps to upload a configuration file by using RCP:
|
|
|
---|---|---|
Verify that the RCP server is properly configured by referring to the “Preparing to Download or Upload a Configuration File By Using RCP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode. This step is required only if you override the default remote username (see Steps 4 and 5). |
||
copy system:running-config rcp: [[[ // [ username @ ] location ] / directory ] / filename ] copy nvram:startup-config rcp: [[[ // [ username @ ] location ] / directory ] / filename ] |
Using RCP, copy the configuration file from a switch running or startup configuration file to a network server. |
This example shows how to copy the running configuration file named switch2-confg to the netadmin1 directory on the remote host with an IP address of 172.16.101.101:
This example shows how to store a startup configuration file on a server:
Clearing Configuration Information
You can clear the configuration information from the startup configuration. If you reboot the switch with no startup configuration, the switch enters the setup program so that you can reconfigure the switch with all new settings.
Clearing the Startup Configuration File
To clear the contents of your startup configuration, use the erase nvram: or the erase startup-config privileged EXEC command.
Deleting a Stored Configuration File
To delete a saved configuration from flash memory, use the delete flash: filename privileged EXEC command. Depending on the setting of the file prompt global configuration command, you might be prompted for confirmation before you delete a file. By default, the switch prompts for confirmation on destructive file operations. For more information about the file prompt command, see the Cisco IOS Command Reference for Release 12.2.
Replacing and Rolling Back Configurations
The configuration replacement and rollback feature replaces the running configuration with any saved Cisco IOS configuration file. You can use the rollback function to roll back to a previous configuration.
Understanding Configuration Replacement and Rollback
To use the configuration replacement and rollback feature, you should understand these concepts:
Archiving a Configuration
The configuration archive provides a mechanism to store, organize, and manage an archive of configuration files. The configure replace privileged EXEC command increases the configuration rollback capability. As an alternative, you can save copies of the running configuration by using the copy running-config destination-url privileged EXEC command, storing the replacement file either locally or remotely. However, this method lacks any automated file management. The configuration replacement and rollback feature can automatically save copies of the running configuration to the configuration archive.
You use the archive config privileged EXEC command to save configurations in the configuration archive by using a standard location and filename prefix that is automatically appended with an incremental version number (and optional timestamp) as each consecutive file is saved. You can specify how many versions of the running configuration are kept in the archive. After the maximum number of files are saved, the oldest file is automatically deleted when the next, most recent file is saved. The show archive privileged EXEC command displays information for all the configuration files saved in the configuration archive.
The Cisco IOS configuration archive, in which the configuration files are stored and available for use with the configure replace command, is in any of these file systems: FTP, HTTP, RCP, TFTP.
Replacing a Configuration
The configure replace privileged EXEC command replaces the running configuration with any saved configuration file. When you enter the configure replace command, the running configuration is compared with the specified replacement configuration, and a set of configuration differences is generated. The resulting differences are used to replace the configuration. The configuration replacement operation is usually completed in no more than three passes. To prevent looping behavior no more than five passes are performed.
You can use the copy source-url running-config privileged EXEC command to copy a stored configuration file to the running configuration. When using this command as an alternative to the configure replace target-url privileged EXEC command, note these major differences:
- The copy source-url running-config command is a merge operation and preserves all the commands from both the source file and the running configuration. This command does not remove commands from the running configuration that are not present in the source file. In contrast, the configure replace target-url command removes commands from the running configuration that are not present in the replacement file and adds commands to the running configuration that are not present.
- You can use a partial configuration file as the source file for the copy source-url running-config command. You must use a complete configuration file as the replacement file for the configure replace target-url command.
Rolling Back a Configuration
You can also use the configure replace command to roll back changes that were made since the previous configuration was saved. Instead of basing the rollback operation on a specific set of changes that were applied, the configuration rollback capability reverts to a specific configuration based on a saved configuration file.
If you want the configuration rollback capability, you must first save the running configuration before making any configuration changes. Then, after entering configuration changes, you can use that saved configuration file to roll back the changes by using the configure replace target-url command.
You can specify any saved configuration file as the rollback configuration. You are not limited to a fixed number of rollbacks, as is the case in some rollback models.
Configuration Guidelines
Follow these guidelines when configuring and performing configuration replacement and rollback:
- Make sure that the switch has free memory larger than the combined size of the two configuration files (the running configuration and the saved replacement configuration). Otherwise, the configuration replacement operation fails.
- Make sure that the switch also has sufficient free memory to execute the configuration replacement or rollback configuration commands.
- Certain configuration commands, such as those pertaining to physical components of a networking device (for example, physical interfaces), cannot be added or removed from the running configuration.
– A configuration replacement operation cannot remove the interface interface-id command line from the running configuration if that interface is physically present on the device.
– The interface interface-id command line cannot be added to the running configuration if no such interface is physically present on the device.
- When using the configure replace command, you must specify a saved configuration as the replacement configuration file for the running configuration. The replacement file must be a complete configuration generated by a Cisco IOS device (for example, a configuration generated by the copy running-config destination-url command).
Note If you generate the replacement configuration file externally, it must comply with the format of files generated by Cisco IOS devices.
Configuring the Configuration Archive
Using the configure replace command with the configuration archive and with the archive config command is optional but offers significant benefit for configuration rollback scenarios. Before using the archive config command, you must first configure the configuration archive. Starting in privileged EXEC mode, follow these steps to configure the configuration archive:
Performing a Configuration Replacement or Rollback Operation
Starting in privileged EXEC mode, follow these steps to replace the running configuration file with a saved configuration file:
Working with Software Images
This section describes how to archive (download and upload) software image files, which contain the system software, the Cisco IOS code, and the embedded device manager software.
Note Instead of using the copy privileged EXEC command or the archive tar privileged EXEC command, we recommend using the archive download-sw and archive upload-sw privileged EXEC commands to download and upload software image files. For switch stacks, the archive download-sw and archive upload-sw privileged EXEC commands can only be used through the stack master. Software images downloaded to the stack master are automatically downloaded to the rest of the stack members.
To upgrade a switch in the stack that has an incompatible software image, use the archive copy-sw privileged EXEC command to copy the software image from an existing stack member to the incompatible switch. That switch automatically reloads and joins the stack as a fully functioning member.
You can download a switch image file from a TFTP, FTP, or RCP server to upgrade the switch software. If you do not have access to a TFTP server, you can download a software image file directly to your PC or workstation by using a web browser (HTTP) and then by using the device manager or Cisco Network Assistant to upgrade your switch. For information about upgrading your switch by using a TFTP server or a web browser (HTTP), see the release notes.
You can replace the current image with the new one or keep the current image in flash memory after a download.
You can use the archive download-sw /allow-feature-upgrade privileged EXEC command to allow installation of an image with a different feature set, for example, upgrading from the IP base image to the IP services image. Beginning in this release, you can also use the boot auto-download-sw global configuration command to specify a URL to use to get an image for automatic software upgrades. When you enter this command, the master switch uses this URL in case of a version mismatch.
You upload a switch image file to a TFTP, FTP, or RCP server for backup purposes. You can use this uploaded image for future downloads to the same switch or to another of the same type.
The protocol that you use depends on which type of server you are using. The FTP and RCP transport mechanisms provide faster performance and more reliable delivery of data than TFTP. These improvements are possible because FTP and RCP are built on and use the TCP/IP stack, which is connection-oriented.
These sections contain this configuration information:
- Image Location on the Switch
- tar File Format of Images on a Server or Cisco.com
- Copying Image Files By Using TFTP
- Copying Image Files By Using FTP
- Copying Image Files By Using RCP
- Copying an Image File from One Stack Member to Another
Note For a list of software images and the supported upgrade paths, see the release notes.
Image Location on the Switch
The Cisco IOS image is stored as a .bin file in a directory that shows the version number. A subdirectory contains the files needed for web management. The image is stored on the system board flash memory (flash:).
You can use the show version privileged EXEC command to see the software version that is currently running on your switch. In the display, check the line that begins with System image file is...
. It shows the directory name in flash memory where the image is stored.
You can also use the dir filesystem : privileged EXEC command to see the directory names of other software images that might be stored in flash memory.The archive download-sw /directory privileged EXEC command allows you to specify a directory one time followed by a tar file or list of tar files to be downloaded instead of specifying complete paths with each tar file. For example, you can enter archive download-sw /directory tftp://10.1.1.10/ c3750-ipservices-tar.122-35.SE.tar c3750-ipbase-tar.122-35.SE.tar.
tar File Format of Images on a Server or Cisco.com
Software images located on a server or downloaded from Cisco.com are provided in a tar file format, which contains these files:
- An info file, which serves as a table of contents for the tar file
- One or more subdirectories containing other images and files, such as Cisco IOS images and web management files
This example shows some of the information contained in the info file. Table C-3 provides additional details about this information:
Copying Image Files By Using TFTP
You can download a switch image from a TFTP server or upload the image from the switch to a TFTP server.
You download a switch image file from a server to upgrade the switch software. You can overwrite the current image with the new one or keep the current image after a download.
You upload a switch image file to a server for backup purposes; this uploaded image can be used for future downloads to the same or another switch of the same type.
Note Instead of using the copy privileged EXEC command or the archive tar privileged EXEC command, we recommend using the archive download-sw and archive upload-sw privileged EXEC commands to download and upload software image files. For switch stacks, the archive download-sw and archive upload-sw privileged EXEC commands can only be used through the stack master. Software images downloaded to the stack master are automatically downloaded to the rest of the stack members.
To upgrade a switch with an incompatible software image, use the archive copy-sw privileged EXEC command to copy the software image from an existing stack member to the incompatible switch. That switch automatically reloads and joins the stack as a fully functioning member.
Preparing to Download or Upload an Image File By Using TFTP
Before you begin downloading or uploading an image file by using TFTP, do these tasks:
- Ensure that the workstation acting as the TFTP server is properly configured. On a Sun workstation, make sure that the /etc/inetd.conf file contains this line:
Make sure that the /etc/services file contains this line:
Note You must restart the inetd daemon after modifying the /etc/inetd.conf and /etc/services files. To restart the daemon, either stop the inetd process and restart it, or enter a fastboot command (on the SunOS 4.x) or a reboot command (on Solaris 2.x or SunOS 5.x). For more information on the TFTP daemon, see the documentation for your workstation.
- Ensure that the switch has a route to the TFTP server. The switch and the TFTP server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the TFTP server by using the ping command.
- Ensure that the image to be downloaded is in the correct directory on the TFTP server (usually / tftpboot on a UNIX workstation).
- For download operations, ensure that the permissions on the file are set correctly. The permission on the file should be world-read.
- Before uploading the image file, you might need to create an empty file on the TFTP server. To create an empty file, enter the touch filename command, where filename is the name of the file you will use when uploading the image to the server.
- During upload operations, if you are overwriting an existing file (including an empty file, if you had to create one) on the server, ensure that the permissions on the file are set correctly. Permissions on the file should be world-write.
Downloading an Image File By Using TFTP
You can download a new image file and replace the current image or keep the current image.
Beginning in privileged EXEC mode, follow Steps 1 through 3 to download a new image from a TFTP server and overwrite the existing image. To keep the current image, go to Step 3.
|
|
|
---|---|---|
Copy the image to the appropriate TFTP directory on the workstation. Make sure that the TFTP server is properly configured; see the “Preparing to Download or Upload an Image File By Using TFTP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
archive download-sw /allow-feature-upgrade /overwrite /reload tftp: [[ // location ] / directory ] / image-name .tar |
Download the image file from the TFTP server to the switch, and overwrite the current image.
|
|
archive download-sw /leave-old-sw /reload tftp: [[ // location ] / directory ] / image-name .tar |
Download the image file from the TFTP server to the switch, and keep the current image.
|
The download algorithm verifies that the image is appropriate for the switch model and that enough DRAM is present, or it aborts the process and reports an error. If you specify the /overwrite option, the download algorithm removes the existing image on the flash device whether or not it is the same as the new one, downloads the new image, and then reloads the software.
Note If the flash device has sufficient space to hold two images and you want to overwrite one of these images with the same version, you must specify the /overwrite option.
If you specify the /leave-old-sw, the existing files are not removed. If there is not enough space to install the new image and keep the running image, the download process stops, and an error message is displayed.
The algorithm installs the downloaded image on the system board flash device (flash:). The image is placed into a new directory named with the software version string, and the BOOT environment variable is updated to point to the newly installed image.
If you kept the old image during the download process (you specified the /leave-old-sw keyword), you can remove it by entering the delete /force /recursive filesystem :/ file-url privileged EXEC command. For filesystem, use flash: for the system board flash device. For file-url, enter the directory name of the old image. All the files in the directory and the directory are removed.
Uploading an Image File By Using TFTP
You can upload an image from the switch to a TFTP server. You can later download this image to the switch or to another switch of the same type.
Use the upload feature only if the web management pages associated with the embedded device manager have been installed with the existing image.
Beginning in privileged EXEC mode, follow these steps to upload an image to a TFTP server:
|
|
|
---|---|---|
Make sure the TFTP server is properly configured; see the “Preparing to Download or Upload an Image File By Using TFTP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
archive upload-sw tftp: [[ // location ] / directory ] / image-name .tar |
Upload the currently running switch image to the TFTP server.
|
The archive upload-sw privileged EXEC command builds an image file on the server by uploading these files in order: info, the Cisco IOS image, and the web management files. After these files are uploaded, the upload algorithm creates the tar file format.
Copying Image Files By Using FTP
You can download a switch image from an FTP server or upload the image from the switch to an FTP server.
You download a switch image file from a server to upgrade the switch software. You can overwrite the current image with the new one or keep the current image after a download.
You upload a switch image file to a server for backup purposes. You can use this uploaded image for future downloads to the switch or another switch of the same type.
Note Instead of using the copy privileged EXEC command or the archive tar privileged EXEC command, we recommend using the archive download-sw and archive upload-sw privileged EXEC commands to download and upload software image files. For switch stacks, the archive download-sw and archive upload-sw privileged EXEC commands can only be used through the stack master. Software images downloaded to the stack master are automatically downloaded to the rest of the stack members.
To upgrade a switch with an incompatible software image, use the archive copy-sw privileged EXEC command to copy the software image from an existing stack member to the incompatible switch. That switch automatically reloads and joins the stack as a fully functioning member.
Preparing to Download or Upload an Image File By Using FTP
You can copy images files to or from an FTP server.
The FTP protocol requires a client to send a remote username and password on each FTP request to a server. When you copy an image file from the switch to a server by using FTP, the Cisco IOS software sends the first valid username in this list:
- The username specified in the archive download-sw or archive upload-sw privileged EXEC command if a username is specified.
- The username set by the ip ftp username username global configuration command if the command is configured.
- Anonymous.
The switch sends the first valid password in this list:
- The password specified in the archive download-sw or archive upload-sw privileged EXEC command if a password is specified.
- The password set by the ip ftp password password global configuration command if the command is configured.
- The switch forms a password named username@switchname.domain. The variable username is the username associated with the current session, switchname is the configured hostname, and domain is the domain of the switch.
The username and password must be associated with an account on the FTP server. If you are writing to the server, the FTP server must be properly configured to accept the FTP write request from you.
Use the ip ftp username and ip ftp password commands to specify a username and password for all copies. Include the username in the archive download-sw or archive upload-sw privileged EXEC command if you want to specify a username only for that operation.
If the server has a directory structure, the image file is written to or copied from the directory associated with the username on the server. For example, if the image file resides in the home directory of a user on the server, specify that user's name as the remote username.
Before you begin downloading or uploading an image file by using FTP, do these tasks:
- Ensure that the switch has a route to the FTP server. The switch and the FTP server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the FTP server by using the ping command.
- If you are accessing the switch through the console or a Telnet session and you do not have a valid username, make sure that the current FTP username is the one that you want to use for the FTP download. You can enter the show users privileged EXEC command to view the valid username. If you do not want to use this username, create a new FTP username by using the ip ftp username username global configuration command. This new name will be used during all archive operations. The new username is stored in NVRAM. If you are accessing the switch through a Telnet session and you have a valid username, this username is used, and you do not need to set the FTP username. Include the username in the archive download-sw or archive upload-sw privileged EXEC command if you want to specify a username for that operation only.
- When you upload an image file to the FTP server, it must be properly configured to accept the write request from the user on the switch.
For more information, see the documentation for your FTP server.
Downloading an Image File By Using FTP
You can download a new image file and overwrite the current image or keep the current image.
Beginning in privileged EXEC mode, follow Steps 1 through 7 to download a new image from an FTP server and overwrite the existing image. To keep the current image, go to Step 7.
|
|
|
---|---|---|
Verify that the FTP server is properly configured by referring to the “Preparing to Download or Upload an Image File By Using FTP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode. This step is required only if you override the default remote username or password (see Steps 4, 5, and 6). |
||
archive download-sw /allow-feature-upgrade /overwrite /reload ftp: [[ // username [ : password ] @ location ] / directory ] / image-name .tar |
Download the image file from the FTP server to the switch, and overwrite the current image.
|
|
archive download-sw /leave-old-sw /reload ftp: [[ // username [ : password ] @ location ] / directory ] / image-name .tar |
Download the image file from the FTP server to the switch, and keep the current image.
|
The download algorithm verifies that the image is appropriate for the switch model and that enough DRAM is present, or it aborts the process and reports an error. If you specify the /overwrite option, the download algorithm removes the existing image on the flash device, whether or not it is the same as the new one, downloads the new image, and then reloads the software.
Note If the flash device has sufficient space to hold two images and you want to overwrite one of these images with the same version, you must specify the /overwrite option.
If you specify the /leave-old-sw, the existing files are not removed. If there is not enough space to install the new image and keep the running image, the download process stops, and an error message is displayed.
The algorithm installs the downloaded image onto the system board flash device (flash:). The image is placed into a new directory named with the software version string, and the BOOT environment variable is updated to point to the newly installed image.
If you kept the old image during the download process (you specified the /leave-old-sw keyword), you can remove it by entering the delete /force /recursive filesystem :/ file-url privileged EXEC command. For filesystem, use flash: for the system board flash device. For file-url, enter the directory name of the old software image. All the files in the directory and the directory are removed.
Uploading an Image File By Using FTP
You can upload an image from the switch to an FTP server. You can later download this image to the same switch or to another switch of the same type.
Use the upload feature only if the web management pages associated with the embedded device manager have been installed with the existing image.
Beginning in privileged EXEC mode, follow these steps to upload an image to an FTP server:
|
|
|
---|---|---|
Verify that the FTP server is properly configured by referring to the “Preparing to Download or Upload a Configuration File By Using FTP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode. This step is required only if you override the default remote username or password (see Steps 4, 5, and 6). |
||
archive upload-sw ftp: [[ // [ username [ : password ] @ ] location ] / directory ] / image-name .tar |
Upload the currently running switch image to the FTP server.
|
The archive upload-sw command builds an image file on the server by uploading these files in order: info, the Cisco IOS image, and the web management files. After these files are uploaded, the upload algorithm creates the tar file format.
Copying Image Files By Using RCP
You can download a switch image from an RCP server or upload the image from the switch to an RCP server.
You download a switch image file from a server to upgrade the switch software. You can overwrite the current image with the new one or keep the current image after a download.
You upload a switch image file to a server for backup purposes. You can use this uploaded image for future downloads to the same switch or another of the same type.
Note Instead of using the copy privileged EXEC command or the archive tar privileged EXEC command, we recommend using the archive download-sw and archive upload-sw privileged EXEC commands to download and upload software image files. For switch stacks, the archive download-sw and archive upload-sw privileged EXEC commands can only be used through the stack master. Software images downloaded to the stack master are automatically downloaded to the rest of the stack members.
To upgrade a switch with an incompatible software image, use the archive copy-sw privileged EXEC command to copy the software image from an existing stack member to the incompatible switch. That switch automatically reloads and joins the stack as a fully functioning member.
Preparing to Download or Upload an Image File By Using RCP
RCP provides another method of downloading and uploading image files between remote hosts and the switch. Unlike TFTP, which uses User Datagram Protocol (UDP), a connectionless protocol, RCP uses TCP, which is connection-oriented.
To use RCP to copy files, the server from or to which you will be copying files must support RCP. The RCP copy commands rely on the rsh server (or daemon) on the remote system. To copy files by using RCP, you do not need to create a server for file distribution as you do with TFTP. You only need to have access to a server that supports the remote shell (rsh). (Most UNIX systems support rsh.) Because you are copying a file from one place to another, you must have read permission on the source file and write permission on the destination file. If the destination file does not exist, RCP creates it for you.
RCP requires a client to send a remote username on each RCP request to a server. When you copy an image from the switch to a server by using RCP, the Cisco IOS software sends the first valid username in this list:
- The username specified in the archive download-sw or archive upload-sw privileged EXEC command if a username is specified.
- The username set by the ip rcmd remote-username username global configuration command if the command is entered.
- The remote username associated with the current TTY (terminal) process. For example, if the user is connected to the router through Telnet and was authenticated through the username command, the switch software sends the Telnet username as the remote username.
- The switch hostname.
For the RCP copy request to execute successfully, an account must be defined on the network server for the remote username. If the server has a directory structure, the image file is written to or copied from the directory associated with the remote username on the server. For example, if the image file resides in the home directory of a user on the server, specify that user’s name as the remote username.
Before you begin downloading or uploading an image file by using RCP, do these tasks:
- Ensure that the workstation acting as the RCP server supports the remote shell (rsh).
- Ensure that the switch has a route to the RCP server. The switch and the server must be in the same subnetwork if you do not have a router to route traffic between subnets. Check connectivity to the RCP server by using the ping command.
- If you are accessing the switch through the console or a Telnet session and you do not have a valid username, make sure that the current RCP username is the one that you want to use for the RCP download. You can enter the show users privileged EXEC command to view the valid username. If you do not want to use this username, create a new RCP username by using the ip rcmd remote-username username global configuration command to be used during all archive operations. The new username is stored in NVRAM. If you are accessing the switch through a Telnet session and you have a valid username, this username is used, and there is no need to set the RCP username. Include the username in the archive download-sw or archive upload-sw privileged EXEC command if you want to specify a username only for that operation.
- When you upload an image to the RCP to the server, it must be properly configured to accept the RCP write request from the user on the switch. For UNIX systems, you must add an entry to the.rhosts file for the remote user on the RCP server.
For example, suppose the switch contains these configuration lines:
If the switch IP address translates to Switch1.company.com, the.rhosts file for User0 on the RCP server should contain this line:
For more information, see the documentation for your RCP server.
Downloading an Image File By Using RCP
You can download a new image file and replace or keep the current image.
Beginning in privileged EXEC mode, follow Steps 1 through 6 to download a new image from an RCP server and overwrite the existing image. To keep the current image, go to Step 6.
|
|
|
---|---|---|
Verify that the RCP server is properly configured by referring to the “Preparing to Download or Upload an Image File By Using RCP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode. This step is required only if you override the default remote username (see Steps 4 and 5). |
||
archive download-sw /allow-feature-upgrade /overwrite /reload rcp: [[[ // [ username @ ] location ] / directory ] / image-name .tar ] |
Download the image file from the RCP server to the switch, and overwrite the current image.
|
|
archive download-sw /leave-old-sw /reload rcp: [[[ // [ username @ ] location ] / directory ] / image-name .tar ] |
Download the image file from the RCP server to the switch, and keep the current image.
|
The download algorithm verifies that the image is appropriate for the switch model and that enough DRAM is present, or it aborts the process and reports an error. If you specify the /overwrite option, the download algorithm removes the existing image on the flash device whether or not it is the same as the new one, downloads the new image, and then reloads the software.
Note If the flash device has sufficient space to hold two images and you want to overwrite one of these images with the same version, you must specify the /overwrite option.
If you specify the /leave-old-sw, the existing files are not removed. If there is not enough room to install the new image an keep the running image, the download process stops, and an error message is displayed.
The algorithm installs the downloaded image onto the system board flash device (flash:). The image is placed into a new directory named with the software version string, and the BOOT environment variable is updated to point to the newly installed image.
If you kept the old software during the download process (you specified the /leave-old-sw keyword), you can remove it by entering the delete /force /recursive filesystem :/ file-url privileged EXEC command. For filesystem, use flash: for the system board flash device. For file-url, enter the directory name of the old software image. All the files in the directory and the directory are removed.
Uploading an Image File By Using RCP
You can upload an image from the switch to an RCP server. You can later download this image to the same switch or to another switch of the same type.
The upload feature should be used only if the web management pages associated with the embedded device manager have been installed with the existing image.
Beginning in privileged EXEC mode, follow these steps to upload an image to an RCP server:
|
|
|
---|---|---|
Verify that the RCP server is properly configured by referring to the “Preparing to Download or Upload an Image File By Using RCP” section. |
||
Log into the switch through the console port or a Telnet session. |
||
Enter global configuration mode. This step is required only if you override the default remote username (see Steps 4 and 5). |
||
archive upload-sw rcp: [[[ // [ username @ ] location ] / directory ] / image-name .tar ] |
Upload the currently running switch image to the RCP server.
|
The archive upload-sw privileged EXEC command builds an image file on the server by uploading these files in order: info, the Cisco IOS image, and the web management files. After these files are uploaded, the upload algorithm creates the tar file format.
Copying an Image File from One Stack Member to Another
For switch stacks, the archive download-sw and archive upload-sw privileged EXEC commands can be used only through the stack master. Software images downloaded to the stack master are automatically downloaded to the rest of the stack members.
To upgrade a switch that has an incompatible software image, use the archive copy-sw privileged EXEC command to copy the software image from an existing stack member to the one that has incompatible software. That switch automatically reloads and joins the stack as a fully functioning member.
Note To successfully use the archive copy-sw privileged EXEC command, you must have downloaded from a TFTP server the images for both the stack member switch being added and the stack master. You use the archive download-sw privileged EXEC command to perform the download.
Beginning in privileged EXEC mode from the stack member that you want to upgrade, follow these steps to copy the running image file from the flash memory of a different stack member: