M Commands

mac-address

mac-address <macaddress> | no mac-address [ <macaddress> ]

Syntax Description

no

Negate a command or set its defaults

mac-address

Virtual MAC address

macaddress

MAC address(FORMAT:xxxx.xxxx.xxxx)
Command Mode
  • /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6

mac-address

mac-address <mac_address_val> | no mac-address [ <mac_address_val> ]

Syntax Description

no

Negate a command or set its defaults

mac-address

Configure interface mac address
Command Mode
  • /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub

mac-address

mac-address { <mac_address_val> | ipv6-extract } | no mac-address [ <mac_address_val> | ipv6-extract ]

Syntax Description

no

Negate a command or set its defaults

mac-address

Configure interface mac address

ipv6-extract

Extract mac-address from the IPv6 address configured on the interface
Command Mode
  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel /exec/configure/if-port-channel-sub /exec/configure/if-remote-ethernet-sub

mac-address

mac-address <mac-addr> | no mac-address

Syntax Description

no

Negate a command or set its defaults

mac-address

Manually set interface MAC address

mac-addr

MAC address
Command Mode
  • /exec/configure/if-vlan-common

mac-address ipv6-extract

mac-address ipv6-extract | no mac-address ipv6-extract

Syntax Description

no

Negate a command or set its defaults

mac-address

Configure interface mac address

ipv6-extract

Extract mac-address from the IPv6 address configured on the interface
Command Mode
  • /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub

mac-list

{ mac-list <name> [ seq <seq> ] { permit | deny } <mac-addr> [ <mac-mask> ] } | { no mac-list <name> [ seq <seq> ] [ { permit | deny } <mac-addr> [ <mac-mask> ] ] }

Syntax Description

no

Negate a command or set its defaults

mac-list

Build a mac list

name

Name of prefix list

seq

(Optional) Sequence number of an entry

seq

(Optional) Sequence number

permit

Specify routes to forward

deny

Specify routes to reject

mac-addr

MAC address

mac-mask

(Optional) MAC Mask. Default Mask is ffff.ffff.ffff
Command Mode
  • /exec/configure

mac access-list

[no] mac access-list <name> [ client <clienttype> <clientID> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

mac

MAC configuration commands

access-list

Configure access list

name

List name

client

(Optional) set client type

clienttype

(Optional) CLI/ONEP

clientID

(Optional) client appID
Command Mode
  • /exec/configure

mac address

[no] mac address { <macaddr> }

Syntax Description

no

(Optional) Negate a command or set its defaults

mac

Configure vMAC address options for Pathway

address

Pathway will use a specified vMAC address

macaddr

48-bit MAC address in HEX
Command Mode
  • /exec/configure/if-eth-any/vrrs

mac address inherit

mac address inherit

Syntax Description

mac

Configure vMAC address options for Pathway

address

Pathway will use a specified vMAC address

inherit

Pathway will inherit vMAC
Command Mode
  • /exec/configure/if-eth-any/vrrs

mac advert interval

[no] mac advert interval | mac advert interval <macint>

Syntax Description

no

Negate a command or set its defaults

mac

Configure vMAC address options for Pathway

advert

Specify vMAC unsolicited advertisements

interval

Specify interval between vMAC unsolicited advertisements

macint

Advertisement Interval in seconds
Command Mode
  • /exec/configure/if-eth-any/vrrs

mac packet-classify

[no] mac packet-classify

Syntax Description

no

(Optional) Negate a command or set its defaults

mac

MAC configuration commands

packet-classify

Force mac classification of packets
Command Mode
  • /exec/configure/if-ethernet-switch /exec/configure/if-remote-ethernet-switch /exec/configure/if-eth-port-channel-switch /exec/configure/if-ethernet-all

mac port access-group

[no] mac port access-group <name>

Syntax Description

no

(Optional) Negate a command or set its defaults

mac

MAC configuration commands

port

Port policy

access-group

Specify access control for packets

name

List name
Command Mode
  • /exec/configure/if-set-acl-l2

management

[no] management

Syntax Description

no

(Optional) Negate a command or set its defaults

management

Allow in-band management access to VLAN Interface IP address
Command Mode
  • /exec/configure/if-vlan-common

map-notify-group

{ [ no ] map-notify-group { <addr> | <addr6> } }

Syntax Description

no

(Optional) Negate a command or set its defaults

map-notify-group

Group address to send and receive site specific Map-Notify messages

addr

IPv4 group address
Command Mode
  • /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid

map-server

{ { [ no ] map-server { <ms> | <ms6> } [ key-type { sha1 | sha2 } ] key <key> } | { [ no ] map-server { <ms> | <ms6> } proxy-reply } }

Syntax Description

no

(Optional) Negate a command or set its defaults

map-server

To interact with Map-Server

ms

Address of IPv4 map-server

key-type

(Optional) Authentication key type, either sha1 or sha2

sha1

(Optional) Use sha1 authenication in Map-Register messages

sha2

(Optional) Use sha2 authenication in Map-Register messages

key

Authentication key used with Map-Server

key

SHA-1 password key

proxy-reply

Request Map-Server to send Map-Replies on behalf of dynamic-EID
Command Mode
  • /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid

match-address

[no] match-address

Syntax Description

no

(Optional) Negate a command or set its defaults

match-address

Match addresses in advertisement packets
Command Mode
  • /exec/configure/if-eth-any/vrrpv3

match

[no] match { { access-group name <acl-name> } | [ not ] { { cos <cos-value> } | any | { eth-src <mac_src> <mac_src_wild> } | { eth-dest <mac_dest> <mac_dest_wild> } | { eth-type <eth-value> } | { vlan <vlan-number> } | { ip-tos <tos-value> <tos-mask> } | { ip-protocol <ip-protocol-value> } | { ip-src-addr <ip-s-addr> <ip-s-mask> } | { ip-dst-addr <ip-d-addr> <ip-d-mask> } | { tcp-src-port <tcp-src-port-addr> } | { tcp-dst-port <tcp-dest-port-addr> } | { udp-src-port <udp-src-port-addr> } | { udp-dst-port <udp-dest-port-addr> } | { input-interface <ifnum> } | { ipv6-src-addr <ipv6-s-addr> <ipv6-s-mask> } | { ipv6-dst-addr <ipv6-d-addr> <ipv6-d-mask> } | { ipv6-protocol <ipv6-protocol-value> } | { ipv6-flowlabel <ipv6-flowlabel-value> } | { icmpv6-type <icmpv6-type-value> } | { icmpv6-code <icmpv6-code-value> } | { ipv4-dscp <ipv4-dscp-list> } | { ipv6-dscp <ipv6-dscp-list> } | { dscp { <dscp-list> | <dscp-enum> } + } | { precedence { <precedence-list> | <prec-enum> } + } | { discard-class <discard-class-list> } | { qos-group <qos-group-list> } | { class-map <cmap-name-plc> } | { protocol <protocol-enum> } | { packet length <len-list> } | { ip rtp <port-list> } | { mpls experimental topmost <exp-list> } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

not

(Optional) Negate this match result

access-group

Access group

name

Named Access List

acl-name

Access List name

cos

IEEE 802.1Q class of service

dscp

DSCP in IP(v4) and IPv6 packets

dscp-list

List of DSCP values

dscp-enum

precedence

Precedence in IP(v4) and IPv6 packets

precedence-list

List of precedence values

prec-enum

discard-class

Discard class

discard-class-list

List of discard-class values

qos-group

Qos-group

qos-group-list

List of qos-group values

class-map

Class map

cmap-name-plc

Match class-map name

protocol

Protocol

protocol-enum

packet

Packet

length

Length of IP datagram

len-list

list of IP packet length

ip

IP

rtp

Real Time Protocol

port-list

UDP port list that are using RTP

mpls

Match on MPLS label

experimental

Match on MPLS Experimental label

topmost

Match on topmost MPLS label

exp-list

List of MPLS exp values

any

Match on Any Filter

eth-dest

Match on Layer 2 destination MAC address

eth-src

Match on Layer 2 source MAC address

eth-type

Match on Ether type

vlan

Match on 802.1Q vlan

ip-tos

Match on IPv4 TOS

ip-protocol

Match on IP protocol

ip-src-addr

Match on IPv4 source address

ip-dst-addr

Match on IPv4 destination address

ipv6-src-addr

Match on IPv6 source address

ipv6-dst-addr

Match on IPv6 destination address

tcp-src-port

Match on TCP source port

tcp-dst-port

Match on TCP source port

udp-src-port

Match on UDP source port

udp-dst-port

Match on UDP source port

input-interface

Match on physical input interface

ipv6-protocol

Match on IPv6 Protocol Value

ipv6-flowlabel

Match on IPv6 Flowlabel

icmpv6-type

Match on ICMPv6 Message Type

icmpv6-code

Match on ICMPv6 Message Code

ipv4-dscp

Match on DSCP for IPV4 Packets

ipv6-dscp

Match on DSCP for IPV6 Packets

cos-value

class of service Value

mac_src

Source MAC address

mac_src_wild

Source MAC mask

mac_dest

Destination MAC address

mac_dest_wild

Destination MAC mask

eth-value

Ethernet type

vlan-number

Vlan number

tos-value

IPv4 TOS

tos-mask

IPV4 TOS Mask for DSCP

ip-protocol-value

IPV4 protocol

ip-s-addr

IPV4 address in format a.b.c.d

ip-d-addr

IPV4 address in format a.b.c.d

ip-s-mask

IPV4 address Mask in format a.b.c.d

ip-d-mask

IPV4 address Mask in format a.b.c.d

tcp-src-port-addr

Transport layer port number

tcp-dest-port-addr

Transport layer port number

udp-src-port-addr

Transport layer port number

udp-dest-port-addr

Transport layer port number

ifnum

Physical interface Name and Number

ipv6-protocol-value

IPv6 Protocol Value

ipv6-flowlabel-value

IPv6 Flowlabel

icmpv6-type-value

ICMPv6 Message Type

icmpv6-code-value

ICMPv6 Message Code

ipv4-dscp-list

List of IPV4 DSCP values

ipv6-dscp-list

List of IPV6 DSCP values
Command Mode
  • /exec/configure/class-map/type/plc

match

[no] match <ip_ipv6_mac> address <name>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Specify the match clause

ip_ipv6_mac

IP/IPv6/MAC

address

Match an access list

name

List name
Command Mode
  • /exec/configure/vacl

match

[no] match { { access-group name <acl-name> } | [ not ] { dscp { <dscp-list> | <dscp-enum> } + } | { qos-group <qos-group-list> } }

Syntax Description

dscp-list

<dscp-enum>

no

(Optional) Negate a command or set its defaults

match

Classification criteria

not

(Optional) Negate this match result

access-group

Access group

name

Named Access List

acl-name

Access List name

dscp

DSCP in IP(v4) and IPv6 packets

dscp-enum

qos-group

Qos-group

qos-group-list

List of qos-group values
Command Mode
  • /exec/configure/class-map

match

[no] match { [ not ] { { cos <cos-list> } | { precedence { <precedence-list> | <prec-enum> } + } | { discard-class <discard-class-list> } | { class-map <cmap-name> } | { protocol <protocol-enum> } | { packet length <len-list> } | { ip rtp <port-list> } | { mpls experimental topmost <exp-list> } } }

Syntax Description

cos-list

<precedence-list>

no

(Optional) Negate a command or set its defaults

match

Classification criteria

not

(Optional) Negate this match result

cos

IEEE 802.1Q class of service

precedence

Precedence in IP(v4) and IPv6 packets

precedence-list

List of precedence values

prec-enum

discard-class

Discard class

discard-class-list

List of discard-class values

class-map

Class map

cmap-name

Match class-map name

protocol

Protocol

protocol-enum

packet

Packet

length

Length of IP datagram

len-list

list of IP packet length

ip

IP

rtp

Real Time Protocol

port-list

UDP port list that are using RTP

mpls

Match on MPLS label

experimental

Match on MPLS Experimental label

topmost

Match on topmost MPLS label

exp-list

List of MPLS exp values
Command Mode
  • /exec/configure/class-map

match access-group name

[no] match access-group name <acs-grp-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

access-group

Match with given access group

name

Name of the access group

acs-grp-name

Match parameter for class-map
Command Mode
  • /exec/configure/cmap

match as-number

[no] match as-number [ { <asnum> | <asnum_range> } + ] { <asnum_trail> | <asnum_range_trail> }

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

as-number

Match BGP peer AS number

asnum

(Optional) <AA4>,

asnum_range

(Optional) <AA4>-<AA4>,

asnum_trail

<AA4>,

asnum_range_trail

<AA4>-<AA4>,
Command Mode
  • /exec/configure/route-map

match as-number as-path-list

match as-number as-path-list <aspl-name> + | no match as-number as-path-list { <aspl-name> | <aspl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

as-number

Match BGP peer AS number

as-path-list

AS-path access-list

aspl-name

aspl-name

aspl-name

Command Mode
  • /exec/configure/route-map

match as-path

match as-path <aspl-name> + | no match as-path { <aspl-name> | <aspl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

as-path

Match BGP AS path list

aspl-name

aspl-name

aspl-name

Command Mode
  • /exec/configure/route-map

match class-map

[no] match class-map <cmap-name>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

class-map

Class map

cmap-name

class map name
Command Mode
  • /exec/configure/class-map/type/queuing

match community

[no] match community <name> + [ exact-match ]

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

community

Match BGP community list

name

Community list name

exact-match

(Optional) Do exact matching of communities
Command Mode
  • /exec/configure/route-map

match cos

[no] match cos <cos-list>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

cos

IEEE 802.1Q class of service

cos-list

List of class-of-service values
Command Mode
  • /exec/configure/class-map/type/queuing

match cos

[no] match cos <cos-list>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

cos

IEEE 802.1Q class of service

cos-list

List of class-of-service values
Command Mode
  • /exec/configure/class-map/type/uf

match datalink

[no] match datalink { mac source-address | mac destination-address | ethertype | vlan }

Syntax Description

match

Specify a key field

datalink

datalink (Layer 2) attributes

mac

MAC Address

source-address

Source MAC Address

destination-address

Destination MAC Address

ethertype

Ethertype

vlan

VLAN ID
Command Mode
  • /exec/configure/nfm-record

match dscp

[no] match dscp { <dscp-list> | <dscp-enum> } +

Syntax Description

dscp-list

<dscp-enum>

no

(Optional) Negate a command or set its defaults

match

Classification criteria

dscp

DSCP in IP(v4) and IPv6 packets

dscp-enum

Command Mode
  • /exec/configure/color-cmap

match dscp

[no] match dscp { <dscp-list> } +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

dscp

DSCP in IP(v4) packets

dscp-list

List of DSCP values
Command Mode
  • /exec/configure/class-map/type/queuing

match exception

[no] match exception { { { ip | ipv6 } { option | { icmp { redirect | unreachable } } | municast } } | ttl-failure | glean | mtu-failure | nat-flow | { multicast { rpf-failure | sg-rpf-failure | dest-miss } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

exception

Match exception packets

ip

ipv4 match criteria

ipv6

ipv6 match criteria

option

Match ip/ipv6 option exception packets

icmp

Icmp redirect packets

redirect

Send redirected packets back to sender

unreachable

Send unreachable packets back to sender

municast

IP unicast packets with multicast MAC

ttl-failure

Failed in ttl

mtu-failure

mtu-failure

glean

Glean packets

multicast

multicast packets

rpf-failure

multicast rpf check failure

sg-rpf-failure

multicast sg rpf check failure

dest-miss

L3 multicast destination lookup failure

nat-flow

ipv4 software nat flow packets
Command Mode
  • /exec/configure/cmap

match extcommunity

[no] match extcommunity <name> + [ exact-match ]

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

extcommunity

Match BGP community list

name

Extended Community list name

exact-match

(Optional) Do exact matching of extended communities
Command Mode
  • /exec/configure/route-map

match interface

[no] match interface <name> +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

interface

Match first hop interface of route

name

Interface name
Command Mode
  • /exec/configure/route-map

match ip

[no] match ip { protocol | tos }

Syntax Description

match

Specify a key field

ip

IP attributes

protocol

Protocol

tos

TOS
Command Mode
  • /exec/configure/nfm-record

match ip address

[no] match ip address <name> +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

ip

Configure IP features

address

Match address of route or match packet

name

IP access-list name (for use in route-maps for PBR only)
Command Mode
  • /exec/configure/route-map

match ip address prefix-list

match ip address prefix-list <ipv4-pfl-name> + | no match ip address prefix-list { <ipv4-pfl-name> | <ipv4-pfl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ip

Configure IP features

address

Match address of route or match packet

prefix-list

Match entries of prefix-lists

ipv4-pfl-name

ipv4-pfl-name

ipv4-pfl-name

Command Mode
  • /exec/configure/route-map

match ip multicast

{ match ip multicast { { rp <iprp> [ rp-type <iprptype> ] } | { group <gprefix> } | { source <ipsrc> } } + } | { match ip multicast { { rp <iprp> [ rp-type <iprptype> ] } | { group-range <gaddr_start> to <gaddr_end> } | { source <ipsrc> } } + } | { no match ip multicast }

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ip

Configure IP features

multicast

Match multicast attributes

rp

Rendezvous point

iprp

IPv4 rendezvous prefix

rp-type

(Optional) Multicast rendezvous point type

iprptype

(Optional) IPv4 rendezvous point type

group

Multicast Group prefix

gprefix

IPv4 group prefix

group-range

Multicast Group address range

gaddr_start

First Group address

to

Range

gaddr_end

Last Group address

source

Multicast source address

ipsrc

IPv4 source prefix
Command Mode
  • /exec/configure/route-map

match ip next-hop prefix-list

match ip next-hop prefix-list <ipv4-pfl-name> + | no match ip next-hop prefix-list { <ipv4-pfl-name> | <ipv4-pfl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ip

Configure IP features

next-hop

Match next-hop address of route

prefix-list

Match entries of prefix-lists

ipv4-pfl-name

ipv4-pfl-name

ipv4-pfl-name

Command Mode
  • /exec/configure/route-map

match ip route-source prefix-list

match ip route-source prefix-list <ipv4-pfl-name> + | no match ip route-source prefix-list { <ipv4-pfl-name> | <ipv4-pfl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ip

Configure IP features

route-source

Match advertising source address of route

prefix-list

Match entries of prefix-lists

ipv4-pfl-name

ipv4-pfl-name

ipv4-pfl-name

Command Mode
  • /exec/configure/route-map

match ipv4

[no] match ipv4 { source | destination } address

Syntax Description

match

Specify a key field

ipv4

IPv4 attributes

source

Source Address

destination

Destination Address

address

Address
Command Mode
  • /exec/configure/nfm-record

match ipv6

[no] match ipv6 { { { source | destination } address } | { flow-label | options } }

Syntax Description

match

Specify a key field

ipv6

IPv6 attributes

source

Source Address

destination

Destination Address

address

Address

flow-label

Flow label

options

Options
Command Mode
  • /exec/configure/nfm-record

match ipv6 address

[no] match ipv6 address <name>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

ipv6

Configure IPv6 features

address

Match address of route or match packet

name

IPv6 access-list name (for use in route-maps for PBR only)
Command Mode
  • /exec/configure/route-map

match ipv6 address prefix-list

match ipv6 address prefix-list <ipv6-pfl-name> + | no match ipv6 address prefix-list { <ipv6-pfl-name> | <ipv6-pfl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ipv6

Configure IPv6 features

address

Match address of route or match packet

prefix-list

Match entries of prefix-lists

ipv6-pfl-name

ipv6-pfl-name

ipv6-pfl-name

Command Mode
  • /exec/configure/route-map

match ipv6 multicast

{ match ipv6 multicast { { rp <ipv6rp> [ rp-type <ipv6rptype> ] } | { group <gprefix> } | { source <ipv6src> } } + } | { match ipv6 multicast { { rp <ipv6rp> [ rp-type <ipv6rptype> ] } | { group-range <gaddr_start> to <gaddr_end> } | { source <ipv6src> } } + } | { no match ipv6 multicast }

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ipv6

Configure IPv6 features

multicast

Match multicast attributes

rp

Rendezvous point

rp-type

(Optional) Multicast rendezvous point type

ipv6rptype

(Optional) IPv6 rendezvous point type

group

Multicast group address

group-range

Multicast Group address range

to

Range

source

Multicast source address
Command Mode
  • /exec/configure/route-map

match ipv6 next-hop prefix-list

match ipv6 next-hop prefix-list <ipv6-pfl-name> + | no match ipv6 next-hop prefix-list { <ipv6-pfl-name> | <ipv6-pfl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ipv6

Configure IPv6 features

next-hop

Match next-hop address of route

prefix-list

Match entries of prefix-lists

ipv6-pfl-name

ipv6-pfl-name

ipv6-pfl-name

Command Mode
  • /exec/configure/route-map

match ipv6 route-source prefix-list

match ipv6 route-source prefix-list <ipv6-pfl-name> + | no match ipv6 route-source prefix-list { <ipv6-pfl-name> | <ipv6-pfl-name> } +

Syntax Description

no

Negate a command or set its defaults

match

Match values from routing table

ipv6

Configure IPv6 features

route-source

Match advertising source address of route

prefix-list

Match entries of prefix-lists

ipv6-pfl-name

ipv6-pfl-name

ipv6-pfl-name

Command Mode
  • /exec/configure/route-map

match metric

[no] match metric { <measure> [ <plus-minus> <deviation> ] } +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

metric

Match metric of route

plus-minus

(Optional) +-

measure

Metric value

deviation

(Optional) Deviation value
Command Mode
  • /exec/configure/route-map

match protocol

[no] match protocol { arp | mpls [ router-alert | exp <exp_value> ] }

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

protocol

Protocol

arp

IP ARP

mpls

Multi-protocol Label Switching

router-alert

(Optional) Match packets with router-alert label set to 1 for OTV Overlay frames

exp

(Optional) Match packets on MPLS exp bits

exp_value

(Optional) Exp bits value
Command Mode
  • /exec/configure/cmap

match protocol

[no] match protocol { fcoe | iscsi | tcp }

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

protocol

Protocol

fcoe

FCoE

iscsi

ISCSI

tcp

TCP
Command Mode
  • /exec/configure/class-map/type/uf

match qos-group

[no] match qos-group { <qos-group-list> } +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

qos-group

QoS Group

qos-group-list

List of qos-group values
Command Mode
  • /exec/configure/class-map/type/queuing

match qos-group

[no] match qos-group <qos-group-list>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

qos-group

QoS Group

qos-group-list

List of qos-group values
Command Mode
  • /exec/configure/class-map/type/uf

match qos-group2 (queuing)

[no] match qos-group2 { <qos-group-list> }

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

qos-group2

QoS Group

qos-group-list

List of qos-group values

Command Mode
  • /exec/configure/class-map/type/queuing

match qos-group2 (uf)

[no] match qos-group2 <qos-group-list>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

qos-group2

QoS Group

qos-group-list

Qos-group value

Command Mode
  • /exec/configure/class-map/type/uf

match redirect

[no] match redirect <opt_match_redirect>

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Classification criteria

redirect

Match redirected packets

opt_match_redirect

Match criteria for redirected packets
Command Mode
  • /exec/configure/cmap

match route-type

[no] match route-type { external | internal | level-1 | level-2 | local | nssa-external | type-1 | type-2 | inter-area | intra-area } +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

route-type

Match route-type of route

external

external route (BGP, EIGRP and OSPF type 1/2)

internal

internal route (including OSPF intra/inter area)

level-1

IS-IS level-1 route

level-2

IS-IS level-2 route

local

locally generated route

nssa-external

nssa-external route (OSPF type 1/2)

type-1

OSPF external type 1 route

type-2

OSPF external type 2 route

inter-area

OSPF inter area route

intra-area

OSPF intra area route
Command Mode
  • /exec/configure/route-map

match source-protocol

[no] match source-protocol <src_prot> +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

source-protocol

Match source protocol

src_prot

Protocol instance name
Command Mode
  • /exec/configure/route-map

match tag

[no] match tag <tagid> +

Syntax Description

no

(Optional) Negate a command or set its defaults

match

Match values from routing table

tag

Match tag of route

tagid

Tag value
Command Mode
  • /exec/configure/route-map

match transport

[no] match transport { destination-port | source-port }

Syntax Description

match

Specify a key field

transport

Transport layer fields

destination-port

Transport destination port

source-port

Transport source port
Command Mode
  • /exec/configure/nfm-record

max-lsa

[no] max-lsa <maximum-number> [ <threshold> ] [ warning-only | [ ignore-time <ignore-time-minutes> ] [ ignore-count <ignore-count-number> ] [ reset-time <reset-time-minutes> ] ]

Syntax Description

no

(Optional) Negate a command or set its defaults

max-lsa

Feature to limit the number of non-self-originated LSAs

maximum-number

Set maximum number of non self-generated LSAs

threshold

(Optional) Threshold value (%) at which to generate a warning message

warning-only

(Optional) Log a warning message when limit is exceeded

ignore-time

(Optional) Set time during which all adjacencies are suppressed

ignore-time-minutes

(Optional) ignore-time in minutes

ignore-count

(Optional) Set count on how many times adjacencies can be suppressed

ignore-count-number

(Optional) ignore-count

reset-time

(Optional) Set number of minutes after which ignore-count is reset to zero

reset-time-minutes

(Optional) reset-time in minutes
Command Mode
  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

max-lsa

[no] max-lsa <maximum-number> [ <threshold> ] [ warning-only | [ ignore-time <ignore-time-minutes> ] [ ignore-count <ignore-count-number> ] [ reset-time <reset-time-minutes> ] ]

Syntax Description

no

(Optional) Negate a command or set its defaults

max-lsa

Feature to limit the number of non-self-originated LSAs

maximum-number

Set maximum number of non self-generated LSAs

threshold

(Optional) Threshold value (%) at which to generate a warning message

warning-only

(Optional) Log a warning message when limit is exceeded

ignore-time

(Optional) Set time during which all adjacencies are suppressed

ignore-time-minutes

(Optional) ignore-time in minutes

ignore-count

(Optional) Set count on how many times adjacencies can be suppressed

ignore-count-number

(Optional) ignore-count

reset-time

(Optional) Set number of minutes after which ignore-count is reset to zero

reset-time-minutes

(Optional) reset-time in minutes
Command Mode
  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

max-lsp-lifetime

max-lsp-lifetime <lifetime> | no max-lsp-lifetime [ <lifetime> ]

Syntax Description

no

Negate a command or set its defaults

max-lsp-lifetime

Set maximum LSP lifetime

lifetime

Maximum LSP lifetime in seconds
Command Mode
  • /exec/configure/otv-isis/otv-isis-vrf-common

max-lsp-lifetime

max-lsp-lifetime <lifetime> | no max-lsp-lifetime [ <lifetime> ]

Syntax Description

no

Negate a command or set its defaults

max-lsp-lifetime

Set maximum LSP lifetime

lifetime

Maximum LSP lifetime in seconds
Command Mode
  • /exec/configure/router-isis/router-isis-vrf-common

max-metric router-lsa

[no] max-metric router-lsa [ external-lsa [ <max-metric-extlsa> ] ] [ include-stub ] [ on-startup [ <timeout> ] [ wait-for bgp <tag> ] ] [ summary-lsa [ <max-metric-sumlsa> ] ]

Syntax Description

no

(Optional) Negate a command or set its defaults

max-metric

Maximize the cost metric

external-lsa

(Optional) External LSAs

max-metric-extlsa

(Optional) Max metric value for external LSAs

include-stub

(Optional) Advertise Max metric for Stub links as well

on-startup

(Optional) Effective only at startup

timeout

(Optional) Wait period in seconds after startup

wait-for

(Optional) Wait for an event to advertise normal metric

bgp

(Optional) BGP Convergence

tag

(Optional) Tag of BGP to wait for

summary-lsa

(Optional) Summary LSAs

max-metric-sumlsa

(Optional) Max metric value for summary LSAs
Command Mode
  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

max-metric router-lsa

[no] max-metric router-lsa [ external-lsa [ <max-metric-extlsa> ] ] [ stub-prefix-lsa ] [ on-startup [ <timeout> ] [ wait-for bgp <tag> ] ] [ inter-area-prefix-lsa [ <max-metric-sumlsa> ] ]

Syntax Description

no

(Optional) Negate a command or set its defaults

max-metric

Maximize the cost metric

external-lsa

(Optional) External LSAs

max-metric-extlsa

(Optional) Max metric value for external LSAs

stub-prefix-lsa

(Optional) Advertise Max metric for Stub links as well

on-startup

(Optional) Effective only at startup

timeout

(Optional) Wait period in seconds after startup

wait-for

(Optional) Wait for an event to advertise normal metric

bgp

(Optional) BGP Convergence

tag

(Optional) Tag of BGP to wait for

inter-area-prefix-lsa

(Optional) Inter-area-prefix LSAs

max-metric-sumlsa

(Optional) Max metric value for summary LSAs
Command Mode
  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

max-ports

[ vmware ] max-ports <i0>

Syntax Description

vmware

(Optional) VMware configuration

max-ports

Max ports on which this profile can be inherited

i0

Enter the max-number of ports
Command Mode
  • /exec/configure/port-profile

max-ports

[no] [ vmware ] max-ports

Syntax Description

no

Negate a command or set its defaults

vmware

(Optional) VMware configuration

max-ports

Max ports on which this profile can be inherited
Command Mode
  • /exec/configure/port-profile

maxas-limit

maxas-limit <as-limit> | no maxas-limit [ <as-limit> ]

Syntax Description

no

Negate a command or set its defaults

maxas-limit

Allow AS-PATH attribute from EBGP neighbor imposing a limit on number of ASes

as-limit

Number of ASes in the AS-PATH attribute
Command Mode
  • /exec/configure/router-bgp/vrf-cmds

maximum-paths

maximum-paths <max-paths> | no maximum-paths [ <max-paths> ]

Syntax Description

no

Negate a command or set its defaults

maximum-paths

RIP set maximum paths per route

max-paths

Maximum paths per prefix
Command Mode
  • /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common

maximum-paths (router-ospf3-af-ipv6)

maximum-paths <max-paths> | no maximum-paths [ <max-paths> ]

Syntax Description

no

Negate a command or set its defaults

maximum-paths

Maximum paths per destination

max-paths

Maximum paths per destination

Command Mode
  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

maximum-paths (router-bgp-af)

maximum-paths [ ibgp ] <mpath-count> | no maximum-paths [ ibgp ] [ <mpath-count> ]

Syntax Description

no

Negate a command or set its defaults

maximum-paths

Forward packets over multipath paths

ibgp

(Optional) Configure multipath for IBGP paths

mpath-count

Number of parallel paths

Command Mode
  • /exec/configure/router-bgp/router-bgp-af

maximum-paths (router-eigrp-af-common)

{ { maximum-paths <num-paths> } | { no maximum-paths [ <num-paths> ] } }

Syntax Description

no

Negate a command or set its defaults

maximum-paths

Forward packets over multiple paths

num-paths

Number of paths

Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

maximum-paths (vrf)

maximum-paths <max-paths> | no maximum-paths [ <max-paths> ]

Syntax Description

no

Negate a command or set its defaults

maximum-paths

Maximum paths per destination

max-paths

Maximum paths per destination

Command Mode
  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

maximum-paths (router-isis-af-ipv6)

maximum-paths <max-paths> | no maximum-paths [ <max-paths> ]

Syntax Description

no

Negate a command or set its defaults

maximum-paths

Set maximum paths per destination

max-paths

Maximum paths per destination

Command Mode
  • /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-ipv6

maximum-paths eibgp

maximum-paths eibgp <mpath-count> | no maximum-paths eibgp [ <mpath-count> ]

Syntax Description

no

Negate a command or set its defaults

maximum-paths

Forward packets over multipath paths

eibgp

Configure multipath for both EBGP and IBGP paths

mpath-count

Number of parallel paths
Command Mode
  • /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6

maximum-peers

{ maximum-peers <limit> | no maximum-peers [ <limit> ] }

Syntax Description

no

Negate a command or set its defaults

maximum-peers

Maximum number of peers for this prefix

limit

Max. peers limit
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor-prefix

maximum-prefix

maximum-prefix <limit> [ <percent> ] [ restart <restart-time> | warning-only ] | { no | default } maximum-prefix [ <limit> [ <percent> ] [ restart <restart-time> | warning-only ] ]

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

maximum-prefix

Maximum number of prefixes from this neighbor

limit

Max. prefix limit

percent

(Optional) Threshold percentage at which to generate a warning

restart

(Optional) Restart bgp connection after limit is exceeded

restart-time

(Optional) Restart interval in minutes

warning-only

(Optional) Only give a warning message when limit is exceeded
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af

maximum-prefix (router-eigrp)

{ { maximum-prefix <value> [ <threshold> ] [ warning-only ] [ restart <time1> ] [ restart-count <count> ] [ reset-time <time2> ] [ dampened ] } | { no maximum-prefix [ <value> [ <threshold> ] [ warning-only ] [ restart <time1> ] [ restart-count <count> ] [ reset-time <time2> ] [ dampened ] ] } }

Syntax Description

no

Negate a command or set its defaults

maximum-prefix

Maximum number of IP prefixes acceptable in aggregate

value

Number of IP prefixes for maximum-prefix limit

threshold

(Optional) Threshold value (%) at which to generate a warning message

warning-only

(Optional) Only give warning message when limit is exceeded

restart

(Optional) Duration for which a prefix source is ignored

time1

(Optional) Restart interval in minutes

restart-count

(Optional) Number of times sessions are auto-restarted

count

(Optional) Number of times

reset-time

(Optional) Duration after which restart history is cleared

time2

(Optional) Reset time in minutes

dampened

(Optional) Exponentially increase restart time interval

Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common
  • /exec/configure/router-eigrp/router-eigrp-af-common

maximum-prefix

maximum-prefix <limit> [ <percent> ] [ restart <restart-time> | warning-only ] | { no | default } maximum-prefix [ <limit> [ <percent> ] [ restart <restart-time> | warning-only ] ]

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

maximum-prefix

Maximum number of prefixes from this neighbor

limit

Max. prefix limit

percent

(Optional) Threshold percentage at which to generate a warning

restart

(Optional) Restart bgp connection after limit is exceeded

restart-time

(Optional) Restart interval in minutes

warning-only

(Optional) Only give a warning message when limit is exceeded

Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn

maximum routes

[no] maximum routes <limit> [ { <warnlevel> [ reinstall <threshold> ] } | warning-only ]

Syntax Description

no

(Optional) Negate a command or set its defaults

maximum

Set a limit

routes

Maximum number of routes allowed in this routing table

limit

Maximum number of routes allowed

warnlevel

(Optional) Threshold value (%) at which to generate a warning msg

reinstall

(Optional) Reinstall previous rejected route due to over maximum route limit

threshold

(Optional) Threshold value (%) at which to reinstall routes back to VRF

warning-only

(Optional) Only give a warning message if limit is exceeded
Command Mode
  • /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6

mcast-group

mcast-group <maddr1> [ <maddr2> ] | no mcast-group

Syntax Description

no

Negate a command or set its defaults

mcast-group

NVE Multicast Group

maddr1

Multicast IP Prefix

maddr2

(Optional) Multicast IP Prefix
Command Mode
  • /exec/configure/if-nve/vni

mdix auto

{ mdix auto | no mdix [ auto ] }

Syntax Description

no

Negate a command or set its defaults

mdix

Enable auto mdix mode

auto

Enable auto mdix mode
Command Mode
  • /exec/configure/if-ethernet-all /exec/configure/if-eth-base

medium

{ medium { broadcast | p2p } | no medium { broadcast | p2p } }

Syntax Description

no

Negate a command or set its defaults

medium

Configure Interface medium mode

broadcast

Broadcast medium

p2p

Point-to-Point medium
Command Mode
  • /exec/configure/if-ethernet-p2p-switch /exec/configure/if-ethernet-p2p /exec/configure/if-ethernet-all /exec/configure/if-eth-l3-non-member /exec/configure/if-port-channel /exec/configure/if-remote-ethernet-sub /exec/configure/if-eth-port-channel-p2p /exec/configure/if-ethernet-p2p-m

medium

medium <medium-type> | no medium <medium-type>

Syntax Description

no

Negate a command or set its defaults

medium

Configure Interface medium mode

medium-type

Command Mode
  • /exec/configure/if-vlan-common

medium broadcast

{ medium broadcast | no medium broadcast }

Syntax Description

no

Negate a command or set its defaults

medium

Configure Interface medium mode

broadcast

Broadcast medium
Command Mode
  • /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p

medium p2p

{ medium p2p | no medium p2p }

Syntax Description

no

Negate a command or set its defaults

medium

Configure Interface medium mode

p2p

Point-to-Point medium
Command Mode
  • /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub

member vni

[no] member vni <vni-range> mcast-group <maddr1> [ <maddr2> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

member

NVE VN-Segment Membership

vni

Virtual Network Identifier

vni-range

vni range, Example: 5000 or 5001-5008

mcast-group

NVE Multicast Group

maddr1

Multicast IP Prefix

maddr2

(Optional) Multicast IP Prefix
Command Mode
  • /exec/configure/if-nve

member vni

[no] member vni <vni-range>

Syntax Description

no

(Optional) Negate a command or set its defaults

member

NVE VN-Segment Membership

vni

Virtual Network Identifier

vni-range

vni range, Example: 5000 or 5001-5008
Command Mode
  • /exec/configure/if-nve

member vni

[no] member vni <vni-range> associate-vrf

Syntax Description

no

(Optional) Negate a command or set its defaults

member

NVE VN-Segment Membership

vni

Virtual Network Identifier

vni-range

vni range, Example: 5000 or 5001-5008

associate-vrf

Associate vni with a vrf
Command Mode
  • /exec/configure/if-nve

merge config

merge config <from-file> [ show-only ]

Syntax Description

merge

merge

config

merge configuration (to running-config)

from-file

the file containing the destination configuration, a patch will be created and applied to the running-config's matching section (format accordning to 'show run section' command output)

show-only

(Optional) only show the patch, don't execute it
Command Mode
  • /exec

message-digest-key

{ { message-digest-key <keyid> md5 <key> } | { no message-digest-key [ <keyid> md5 <key> ] } }

Syntax Description

no

Negate a command or set its defaults

message-digest-key

Message digest authentication password (key)

keyid

Key ID

md5

Use MD5 algorithm

key

The OSPF password (key)
Command Mode
  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

message-digest-key (router-ospf-slink)

{ { message-digest-key <keyid> md5 <key> } | { no message-digest-key [ <keyid> md5 <key> ] } }

Syntax Description

no

Negate a command or set its defaults

message-digest-key

Message digest authentication password (key)

keyid

Key ID

md5

Use MD5 algorithm

key

OSPF password (key)

Command Mode
  • /exec/configure/router-ospf/vrf/router-ospf-slink

metric-style

[no] metric-style { transition }

Syntax Description

no

(Optional) Negate a command or set its defaults

metric-style

Configure metric style used in advertised LSPs

transition

Use both narrow and wide metric style
Command Mode
  • /exec/configure/router-isis/router-isis-vrf-common

metric direct 0

[no] metric direct 0

Syntax Description

no

(Optional) Negate a command or set its defaults

metric

Cost of direct routes

direct

Cost of direct routes

0

direct route cost is zero to be compatible with IOS
Command Mode
  • /exec/configure/router-rip

metric maximum-hops

{ { metric maximum-hops <hops> } | { no metric maximum-hops [ <hops> ] } }

Syntax Description

no

Negate a command or set its defaults

metric

Modify EIGRP routing metrics and parameters

maximum-hops

Advertise EIGRP routes greater than <hops> as unreachable

hops

Hop count
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

metric rib-scale

{ { metric rib-scale <ribscale> } | { no metric rib-scale [ <ribscale> ] } }

Syntax Description

no

Negate a command or set its defaults

metric

Modify EIGRP routing metrics and parameters

rib-scale

Defines RIB scaling value

ribscale

Rib scale
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

metric version 64bit

{ { metric version 64bit } | { no metric version [ 64bit ] } }

Syntax Description

no

Negate a command or set its defaults

metric

Modify EIGRP routing metrics and parameters

version

Modify EIGRP metric version

64bit

64 bit metric version
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

metric weights

{ { metric weights <tos> <k1> <k2> <k3> <k4> <k5> [ <k6> ] } | { no metric weights [ <tos> <k1> <k2> <k3> <k4> <k5> [ <k6> ] ] } }

Syntax Description

no

Negate a command or set its defaults

metric

Modify EIGRP routing metrics and parameters

weights

Modify EIGRP metric coefficients

tos

Type Of Service (Only TOS 0 supported)

k1

K1

k2

K2

k3

K3

k4

K4

k5

K5

k6

(Optional) K6
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

mgmt-policy

{ no mgmt-policy <policy-name> } | { mgmt-policy <policy-name> { permit | deny } [ [ ip { <ip-addr> [ <ip-mask> ] } ] | [ ip6 <ipv6-prefix> ] ] [ protocol { tcp | udp | icmp } ] [ src-port <srcport> [ <srcport-end> ] ] [ dest-port <dstport> [ <dstport-end> ] ] }

Syntax Description

no

Negate a command or set its defaults

mgmt-policy

PM Management Policy

policy-name

Name of the policy

permit

Permit access

deny

Deny access

ip

(Optional) IPV4 address

ip-addr

(Optional) IPV4 source address/subnet

ip-mask

(Optional) IPV4 mask

ip6

(Optional) IPV6 Address

protocol

(Optional) Protocol

tcp

(Optional) TCP protocol

udp

(Optional) UDP protocol

icmp

(Optional) ICMP protocol

src-port

(Optional) Source port

srcport

(Optional) Source port

srcport-end

(Optional) Source Port end

dest-port

(Optional) Destination port

dstport

(Optional) Destination port

dstport-end

(Optional) Destination Port end
Command Mode
  • /exec/configure

mkdir

mkdir <uri0>

Syntax Description

mkdir

Create new directory

uri0

Directory name
Command Mode
  • /exec

mode

[no] mode <mode-id>

Syntax Description

no

(Optional) Negate a command or set its defaults

mode

Hot-standby mode

mode-id

Node Mode
Command Mode
  • /exec/configure/itd-dg-node

mode

[no] mode <numsample> every <period>

Syntax Description

mode

Define the Sampler mode

numsample

Number of samples per sampling - 64 max

every

Time-based sampling

period

Sampling Time Period in millseconds - 64000 max
Command Mode
  • /exec/configure/nfm-sampler

mode

[no] mode <numsample> out-of <samples> | no mode

Syntax Description

mode

Define the Sampler mode

numsample

Number of samples per sampling - 63 max

out-of

M out of N packets

samples

Number of packets in each sampling - 8191 max
Command Mode
  • /exec/configure/nfm-sampler

mode openflow

[no] mode openflow

Syntax Description

no

(Optional) Negate a command or set its defaults

mode

Configure the interface operational mode

openflow

Disable/Enable openflow on the interface
Command Mode
  • /exec/configure/if-port-channel /exec/configure/if-ethernet-all /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-eth-non-member

mode tap-aggregation

[no] mode tap-aggregation

Syntax Description

no

(Optional) Negate a command or set its defaults

mode

Configure the interface operational mode

tap-aggregation

Disable/Enable tap aggregation on the interface
Command Mode
  • /exec/configure/if-switching

monitor erspan granularity

[no] monitor erspan granularity { 100_ms | 100_ns | 1588 | ns }

Syntax Description

no

(Optional) Negate a command or set its defaults

monitor

Configure Ethernet SPAN sessions

erspan

Configure Ethernet ERSPAN sessions

granularity

Configure granularity for ERSPAN Type III sessions

100_ms

100 microseconds

100_ns

100 nanoseconds

1588

1588 in seconds/nanoseconds

ns

nanoseconds
Command Mode
  • /exec/configure

monitor erspan origin ip-address

[no] monitor erspan origin ip-address <ip> [ global ]

Syntax Description

no

(Optional) Negate a command or set its defaults

monitor

Configure Ethernet SPAN sessions

erspan

Configure Ethernet ERSPAN sessions

origin

Configure the erspan origin ip address

ip-address

Configure global origin IP address

ip

global

(Optional) Configure in default VDC across all VDCs
Command Mode
  • /exec/configure

monitor erspan switch-id

[no] monitor erspan switch-id <switch_id>

Syntax Description

no

(Optional) Negate a command or set its defaults

monitor

Configure Ethernet SPAN sessions

erspan

Configure Ethernet ERSPAN sessions

switch-id

Configure the erspan switch-id

switch_id

erspan-switch-id
Command Mode
  • /exec/configure

move

move <uri0> <uri1>

Syntax Description

move

Move files

uri0

Source file path

uri1

Destination file path
Command Mode
  • /exec

mping

mping [ { broadcast | lc module <i0> | sup module <i1> } ]

Syntax Description

mping

run mping

broadcast

(Optional) mping broadcast

lc

(Optional) mping line-cards

module

(Optional) slot information

i0

(Optional)

sup

(Optional) mping supervisor

module

(Optional) slot information

i1

(Optional)

Command Mode
  • /exec

mpls traffic-eng tunnels

[no] mpls traffic-eng tunnels

Syntax Description

no

(Optional) Negate a command or set its defaults

mpls

MPLS configuration commands

traffic-eng

Configure Traffic Engineering parameters

tunnels

enable MPLS Traffic Engineering tunnels
Command Mode
  • /exec/configure/if-igp /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

mst

mst <mst-id> designated priority <prio> | no mst <mst-id> designated priority [ <prio> ]

Syntax Description

no

Negate a command or set its defaults

mst

Multiple spanning tree configuration

mst-id

MST instance range, example: 0-3,5,7-9

designated

Set the designated bridge priority for the spanning tree

priority

Set the bridge priority for the spanning tree

prio

bridge priority in increments of 4096
Command Mode
  • /exec/configure/spanning-tree/pseudo

mst

mst <mst-id> root priority <prio> | no mst <mst-id> root priority [ <prio> ]

Syntax Description

no

Negate a command or set its defaults

mst

Multiple spanning tree configuration

mst-id

MST instance range, example: 0-3,5,7-9

root

Set the root bridge priority for the spanning tree

priority

Set the bridge priority for the spanning tree

prio

bridge priority in increments of 4096
Command Mode
  • /exec/configure/spanning-tree/pseudo

mtu

[no] mtu [ <mtu-val> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

mtu

Configure MTU

mtu-val

(Optional) Bytes
Command Mode
  • /exec/configure/if-any-tunnel

mtu1

[no] mtu1 <value>

Syntax Description

no

(Optional) Negate a command or set its defaults

mtu1

MTU for the CoS

value

MTU value
Command Mode
  • /exec/configure/policy-map/type/uf/class

mtu

mtu <mtu_val> | no mtu [ <mtu_val> ]

Syntax Description

no

Negate a command or set its defaults

mtu

Configure mtu for the port

mtu_val

Command Mode
  • /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub /exec/configure/if-sub /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

mtu

[no] mtu <value>

Syntax Description

no

(Optional) Negate a command or set its defaults

mtu

MTU for the CoS

value

MTU value
Command Mode
  • /exec/configure/policy-map/type/uf/class

mtu

mtu <mtu_val> | no mtu

Syntax Description

no

Negate a command or set its defaults

mtu

Set the interface Maximum Transmission Unit (MTU)

mtu_val

MTU size in bytes
Command Mode
  • /exec/configure/if-vlan-common

multi-topology

[no] multi-topology [ transition ]

Syntax Description

no

(Optional) Negate a command or set its defaults

multi-topology

Enable multitopoloy for IPV6

transition

(Optional) Configure multitopology transition mode
Command Mode
  • /exec/configure/router-isis/router-isis-af-ipv6