D Commands

dampen-igp-metric

dampen-igp-metric <sec> | no dampen-igp-metric

Syntax Description

no

Negate a command or set its defaults

dampen-igp-metric

Dampen IGP metric-related changes

sec

Time interval in seconds
Command Mode
  • /exec/configure/router-bgp/router-bgp-af

dampening

[no] dampening [ { <half-life> <reuse-limit> <suppress-limit> <max-suppress-time> } | { route-map <rmap-name> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

dampening

Configure route flap dampening

half-life

(Optional) Decay half life

reuse-limit

(Optional) Value to start reusing a route

suppress-limit

(Optional) Value to start suppressing a route

max-suppress-time

(Optional) Maximum suppress time for stable route

route-map

(Optional) Apply route-map to specify dampening criteria

rmap-name

(Optional) Route-map name
Command Mode
  • /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-ipv4-mdt /exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn

data-pattern

{ { no | default } data-pattern | data-pattern <hex-pattern> }

Syntax Description

no

default

Set a command to its defaults

data-pattern

Data Pattern

hex-pattern

Data Pattern in Hex
Command Mode
  • /exec/configure/ip-sla/udp

database-mapping

{ [ no ] database-mapping { <eid-prefix> | <eid-prefix6> } { redistribute | { { <locator> | <locator6> } priority <priority> weight <weight> } } }

Syntax Description

no

(Optional) Negate a command or set its defaults

database-mapping

Configure EID-prefix and locator-set for dynamic-EID

eid-prefix

IP EID-prefix for RLOC static mapping

locator

IP address of LISP-VM routers

priority

Configures which Locators from a set are preferred

priority

Lower priority Locator takes preference

weight

Traffic load-spreading among Locators

weight

Specified in a percentage from 0 to 100

redistribute

Used for redistirbuting into routing protocols
Command Mode
  • /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid

databits

[no] databits <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

databits

Set number of databits per character

i0

Number of data bits
Command Mode
  • /exec/configure/com1

databits

[no] databits <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

databits

Set number of databits per character

i0

Number of data bits
Command Mode
  • /exec/configure/console

datapath transport mts

[no] datapath transport mts

Syntax Description

no

(Optional) Negate a command or set its defaults

datapath

One Platform datapath

transport

transport for datapath

mts

mts
Command Mode
  • /exec/configure/onep

db-jid

[no] db-jid <jid> [ key-type <key-type> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

db-jid

Jabber ID of database

jid

Enter Jabber ID of database

key-type

(Optional) Query key type for this database

key-type

(Optional)

Command Mode
  • /exec/configure/fabric-db/server-xmpp

db-security user

[no] db-security user <user> password { 0 <clear> | 7 <encrypted> | <password> } [ shared-secret { 10 <clear> | 7 <encrypted> | <secret> } ]

Syntax Description

no

(Optional) Negate a command or set its defaults

db-security

Database Security

user

User ID

user

Enter user ID

password

Password

0

Password that follows should be in clear text

clear

Password in clear text

7

Password that follows should be in encrypted text

encrypted

Encrypted password

password

Enter password in clear text

shared-secret

(Optional) Shared-secret

10

(Optional) Indicates that password that follows should be in clear text

clear

(Optional) Password in clear text

7

(Optional) Password that follows should be in encrypted text

encrypted

(Optional) Encrypted password

secret

(Optional) Enter shared-secret in clear text
Command Mode
  • /exec/configure/fabric-db/server-ldap

db-table

[no] db-table <tablename> [ key-type <key-type> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

db-table

Table name to search

tablename

Enter table name to search

key-type

(Optional) Query key type for this table

key-type

(Optional)

Command Mode
  • /exec/configure/fabric-db/server-ldap

dead-interval

{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

dead-interval

Dead interval

interval

(seconds)
Command Mode
  • /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink

dead-interval

{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

dead-interval

Dead interval

interval

(seconds)
Command Mode
  • /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink

dead-interval

{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }

Syntax Description

no

Negate a command or set its defaults

dead-interval

Dead interval

interval

(seconds)
Command Mode
  • /exec/configure/router-ospf/vrf/router-ospf-slink

deadtime

[no] deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

deadtime

duration for which non-reachable server is skipped

i0

Length of time, in minutes
Command Mode
  • /exec/configure/radius

deadtime

[no] deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

deadtime

duration for which non-reachable server is skipped

i0

Length of time, in minutes
Command Mode
  • /exec/configure/ldap

deadtime

[no] deadtime <i0>

Syntax Description

no

(Optional) Negate a command or set its defaults

deadtime

duration for which non-reachable server is skipped

i0

Length of time, in minutes
Command Mode
  • /exec/configure/tacacs+

dec

dec <expr>

Syntax Description

dec

calculator with results in decimal format

expr

the expression to compute (integer arithmetics)
Command Mode
  • /exec

default-information originate

[no] default-information originate [ always ] [ route-map <map-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

RIP control distribution of default route

originate

RIP distribute a default route

always

(Optional) RIP always advertise default route

route-map

(Optional) Policy to constrain redistribution

map-name

(Optional) Route-map name
Command Mode
  • /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common

default-information originate

[no] default-information originate [ always ] [ route-map <policy-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control distribution of default route

originate

Distribute a default route

always

(Optional) Always advertise default route

route-map

(Optional) Policy to control distribution of default route

policy-name

(Optional) Route-map name
Command Mode
  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

default-information originate

[no] default-information originate

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control distribution of default information

originate

Distribute a default route
Command Mode
  • /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-ipv6-label /exec/configure/router-bgp/router-bgp-af-ipv4-label

default-information originate

[no] default-information originate [ always ] [ route-map <map> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control origination of a default route

originate

Originate a default route

always

(Optional) Always advertise default route

route-map

(Optional) Use a route-map for default route metrics

map

(Optional) Route-map name
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

default-information originate

[no] default-information originate [ always ] [ route-map <policy-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control distribution of default route

originate

Distribute a default route

always

(Optional) Always advertise default route

route-map

(Optional) Policy to control distribution of default route

policy-name

(Optional) Route-map name
Command Mode
  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

default-information originate

[no] default-information originate [ always ] [ route-map <map-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default-information

Control origination of a default route

originate

Originate a default route

always

(Optional) Always advertise default route

route-map

(Optional) Route-map to announce default routes

map-name

(Optional) A 'routing-rules' route-map name
Command Mode
  • /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-common

default-metric

default-metric <metric> | no default-metric [ <metric> ]

Syntax Description

no

Negate a command or set its defaults

default-metric

RIP default metric

metric

RIP metric value
Command Mode
  • /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common

default-metric

{ default-metric <cost> } | { no default-metric [ <cost> ] }

Syntax Description

no

Negate a command or set its defaults

default-metric

Specify default metric for redistributed routes

cost

Metric value
Command Mode
  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

default-metric

[no] default-metric <metric>

Syntax Description

no

(Optional) Negate a command or set its defaults

default-metric

Set metric of redistributed routes

metric

Default Metric
Command Mode
  • /exec/configure/router-bgp/router-bgp-af

default-metric

{ { default-metric <bw> <delay> <rel> <load> <mtu> } | { no default-metric [ <bw> <delay> <rel> <load> <mtu> ] } }

Syntax Description

no

Negate a command or set its defaults

default-metric

Set metric of redistributed routes

bw

Bandwidth in Kbits per second

delay

Delay metric

rel

Reliability metric where 255 is 100% reliable

load

Effective bandwidth metric (Loading) where 255 is 100% loaded

mtu

Maximum Transmission Unit metric of the path
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

default-metric

{ default-metric <cost> } | { no default-metric [ <cost> ] }

Syntax Description

no

Negate a command or set its defaults

default-metric

Specify default metric for redistributed routes

cost

Metric value
Command Mode
  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

default-originate

[ no | default ] default-originate [ route-map <rmap-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

default-originate

Originate a default toward this peer

route-map

(Optional) Route-map to specify criteria for originating default

rmap-name

(Optional) Route-map name
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af

define

[no] define <paramname> [ <paramtype> ] [ <paramdesc> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

define

Define a parameter

paramname

Enter the name of the parameter

paramtype

(Optional) param type

paramdesc

(Optional) Enter the parameter description
Command Mode
  • /exec/configure/param-list

delay

delay { { up <up_delay> [ down <down_delay> ] } | { down <down_delay> [ up <up_delay> ] } } | no delay

Syntax Description

no

Negate a command or set its defaults

delay

Tracking delay

up

Delay up change notification

up_delay

Seconds to delay

down

(Optional) Delay down change notification

down_delay

(Optional) Seconds to delay
Command Mode
  • /exec/configure/track /exec/configure/tr-list-bool /exec/configure/tr-list-thrp /exec/configure/tr-list-thrw

delay

delay <delay_val> | no delay [ <delay_val> ]

Syntax Description

no

Negate a command or set its defaults

delay

Specify interface throughput delay

delay_val

Throughput delay (tens of microseconds)
Command Mode
  • /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub

delay

delay <delay_val> | no delay [ <delay_val> ]

Syntax Description

no

Negate a command or set its defaults

delay

Specify interface throughput delay

delay_val

Throughput delay (tens of microseconds)
Command Mode
  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel /exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-remote-ethernet-sub /exec/configure/if-port-channel-range

delay

delay <microseconds> | no delay

Syntax Description

no

Negate a command or set its defaults

delay

Specify interface throughput delay

microseconds

Throughput delay (tens of microseconds)
Command Mode
  • /exec/configure/if-vlan-common

delay restore

delay restore <time-out> | no delay restore

Syntax Description

no

Negate a command or set its defaults

delay

Initialization delay

restore

Delay after restoring peer-link

time-out

Delay in bringing up the vPC links (in seconds)
Command Mode
  • /exec/configure/vpc-domain

delay restore interface-vlan

delay restore interface-vlan <time-out> | no delay restore interface-vlan

Syntax Description

no

Negate a command or set its defaults

delay

Initialization delay

restore

Delay after restoring peer-link

interface-vlan

Delay in bringing-up interface-vlan

time-out

Delay in bringing up the interface-vlan (in seconds)
Command Mode
  • /exec/configure/vpc-domain

delete

delete { <uri0> | <uri1> | <uri2> } [ no-prompt ]

Syntax Description

delete

delete a file or directory

uri0

Delete a file or directory

uri1

Delete a file or directory on expansion flash

uri2

Directory or filename on logflash

no-prompt

(Optional) Do not prompt for multiple deletion of files
Command Mode
  • /exec

delete ca-certificate

delete ca-certificate

Syntax Description

delete

Delete the certificates

ca-certificate

Delete the ca certificates
Command Mode
  • /exec/configure/trustpoint

delete certificate

delete certificate [ force ]

Syntax Description

delete

Delete the certificates

certificate

Delete the identity certificate

force

(Optional) Force delete the identity certificate
Command Mode
  • /exec/configure/trustpoint

delete crl

delete crl

Syntax Description

delete

Delete the certificates

crl

Delete the CRL
Command Mode
  • /exec/configure/trustpoint

demand-circuit

[no] demand-circuit

Syntax Description

no

(Optional) Negate a command or set its defaults

demand-circuit

OSPF Demand circuit
Command Mode
  • /exec/configure/router-ospf/vrf/router-ospf-slink

description

description <describe> | { no | default } description [ <describe> ]

Syntax Description

no

Negate a command or set its defaults

default

Inherit values from a peer template

description

Neighbor specific description

describe

Upto 80 characters describing this neighbor
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor-sess

description

description [ port-profile ] <desc_line> | no description [ port-profile ] [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter port-profile description of maximum 80 characters

port-profile

(Optional) Hack for conf-sync

desc_line

Enter port-profile description of maximum 80 characters
Command Mode
  • /exec/configure/port-profile

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 254 characters

desc_line

Description of maximum 254 characters
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-eth-port-channel /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub /exec/configure/if-mgmt-ether /exec/configure/if-loopback /exec/configure/if-nve /exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-remote-ethernet-sub /exec/configure/if-port-channel-range

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 80 characters

desc_line

Description of maximum 80 characters
Command Mode
  • /exec/configure/if-overlay /exec/configure/if-te /exec/configure/if-nve

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Class-Map description

desc-str

Description of this class-map (up to 200 characters)
Command Mode
  • /exec/configure/class-map/type/uf

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Policy-Map description

desc-str

Description of this policy-map (up to 200 characters)
Command Mode
  • /exec/configure/policy-map/type/uf

description

{ [ no ] description <text> }

Syntax Description

description

description for this profile

text

description
Command Mode
  • /exec/configure/dot1x-cred

description

{ description <line> } | { no description }

Syntax Description

no

Negate a command or set its defaults

description

Description of the VRF

line

VRF description string
Command Mode
  • /exec/configure/vrf

description

{ description <description_text> | no description [ <description_text> ] }

Syntax Description

no

Negate a command or set its defaults

description

Virtual service description

description_text

Description of this virtual service
Command Mode
  • /exec/configure/virt-serv

description

description <desc_line> | no description

Syntax Description

no

Negate a command or set its defaults

description

Interface specific description

desc_line

Up to 255 characters describing this interface
Command Mode
  • /exec/configure/if-vlan-common

description

{ [ no ] description <descrip-string> }

Syntax Description

no

(Optional) Negate a command or set its defaults

description

Provide a description string for the LISP site

descrip-string

Description string
Command Mode
  • /exec/configure/lisp-site /exec/configure/vrf/lisp-site

description

[no] description <description>

Syntax Description

no

(Optional) Negate a command or set its defaults

description

Configure description for the policy

description

Description for the policy
Command Mode
  • /exec/configure/event-manager-applet

description

[no] description

Syntax Description

no

Negate a command or set its defaults

description

Configure description for the policy
Command Mode
  • /exec/configure/event-manager-applet

description

{ description <line> | no description }

Syntax Description

no

Negate a command or set its defaults

description

Description of the route-map

line

Route-map description string
Command Mode
  • /exec/configure/route-map

description

description <line> | no description

Syntax Description

no

Negate a command or set its defaults

description

Add a description for the role

line

Enter the description string(can include spaces)
Command Mode
  • /exec/configure/role

description

description <desc_line> | no description [ <desc_line> ]

Syntax Description

no

Negate a command or set its defaults

description

Enter description of maximum 254 characters

desc_line

Description of maximum 254 characters
Command Mode
  • /exec/configure/if-any-tunnel

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Class-Map description

desc-str

Description of this class-map (up to 200 characters)
Command Mode
  • /exec/configure/class-map

description

[no] description <desc-str>

Syntax Description

no

(Optional) Negate a command or set its defaults

description

Class-Map description

desc-str

Description of this class-map (up to 200 characters)
Command Mode
  • /exec/configure/class-map/type/queuing

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Table-Map description

desc-str

Description of this table-map (up to 200 characters)
Command Mode
  • /exec/configure/table-map

description

{ description <desc-str> | no description [ <desc-str> ] }

Syntax Description

no

Negate a command or set its defaults

description

Policy-Map description

desc-str

Description of this policy-map (up to 200 characters)
Command Mode
  • /exec/configure/policy-map /exec/configure/policy-map/type/queuing

description

[no] description [ <desc> ] | description <desc>

Syntax Description

no

Negate a command or set its defaults

description

Group description

desc

(Optional) Up to 80 characters describing this group
Command Mode
  • /exec/configure/if-eth-any/vrrpv3

description

[no] description | description <desc>

Syntax Description

no

(Optional) Negate a command or set its defaults

description

Pathway description

desc

Up to 80 characters describing this pathway
Command Mode
  • /exec/configure/if-eth-any/vrrs

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Record

line

Record description string (63 characters maximum)
Command Mode
  • /exec/configure/nfm-record

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Monitor

line

Monitor description string (63 characters maximum)
Command Mode
  • /exec/configure/nfm-monitor

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Exporter

line

Monitor description string (63 characters maximum)
Command Mode
  • /exec/configure/nfm-exporter

description

{ [ no ] description <line> | no description }

Syntax Description

description

Provide a description for this Flow Sampler

line

Sampler description string (63 characters maximum)
Command Mode
  • /exec/configure/nfm-sampler

dest-ipaddr

{ { no | default } dest-ipaddr | dest-ipaddr { <ip-address> | <hostname> } }

Syntax Description

no

Negate a command or set its defaults

default

Set a command to its defaults

dest-ipaddr

Destination ip address

ip-address

IP address, broadcast disallowed

hostname

IP Hostname, broadcast disallowed
Command Mode
  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp

dest-port

{ { no | default } dest-port | dest-port <port> }

Syntax Description

no

default

Set a command to its defaults

dest-port

Destination port

port

udp port number
Command Mode
  • /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp

destination-profile

[no] destination-profile <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s0

User defined destination profile name
Command Mode
  • /exec/configure/callhome

destination-profile

[no] destination-profile <s0> email-addr <s1>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s0

User defined destination profile name

email-addr

Add email addr

s1

Provide email address, example: jdow@xyz.com
Command Mode
  • /exec/configure/callhome

destination-profile

[no] destination-profile <s4> { http <s2> }

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s4

User defined destination profile name

http

Add http or https url

s2

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL
Command Mode
  • /exec/configure/callhome

destination-profile

[no] destination-profile <s5> transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s5

User defined destination profile name

transport-method

Callhome message sending transport-method

email

email transport-method
Command Mode
  • /exec/configure/callhome

destination-profile

[no] destination-profile <s6> transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

s6

User defined destination profile name

transport-method

Callhome message sending transport-method

http

http transport-method
Command Mode
  • /exec/configure/callhome

destination-profile

destination-profile <s0> format { full-txt | short-txt | XML }

Syntax Description

destination-profile

Configure destination profiles

s0

User defined destination profile name

format

Callhome message format (default XML)

full-txt

Plain text message format

short-txt

Short text message format

XML

XML message format
Command Mode
  • /exec/configure/callhome

destination-profile

destination-profile <s0> message-level <i0>

Syntax Description

destination-profile

Configure destination profiles

s0

User defined destination profile name

message-level

Callhome message level(0-lowest urgency, 9-highest urgency)

i0

Command Mode
  • /exec/configure/callhome

destination-profile

destination-profile <s0> message-size <i0>

Syntax Description

destination-profile

Configure destination profiles

s0

User defined destination profile name

message-size

Configure maximum message size (default 2500000)

i0

Provide maximum possible message size
Command Mode
  • /exec/configure/callhome

destination-profile CiscoTAC-1 email-addr

[no] destination-profile CiscoTAC-1 email-addr <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

email-addr

Add email addr

s0

Provide email address, example: jdow@xyz.com
Command Mode
  • /exec/configure/callhome

destination-profile CiscoTAC-1 http

[no] destination-profile CiscoTAC-1 http <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

http

Add http or https url

s0

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL
Command Mode
  • /exec/configure/callhome

destination-profile CiscoTAC-1 message-level

destination-profile CiscoTAC-1 message-level <i0>

Syntax Description

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

message-level

Callhome message level(0-lowest urgency, 9-highest urgency)

i0

Command Mode
  • /exec/configure/callhome

destination-profile CiscoTAC-1 message-size

destination-profile CiscoTAC-1 message-size <i0>

Syntax Description

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

message-size

Configure maximum message size (default 5000000)

i0

Provide maximum possible message size
Command Mode
  • /exec/configure/callhome

destination-profile CiscoTAC-1 transport-method email

[no] destination-profile CiscoTAC-1 transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

transport-method

Callhome message sending transport-method

email

email transport-method
Command Mode
  • /exec/configure/callhome

destination-profile CiscoTAC-1 transport-method http

[no] destination-profile CiscoTAC-1 transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

CiscoTAC-1

Configure destination profile for XML message

transport-method

Callhome message sending transport-method

http

http transport-method
Command Mode
  • /exec/configure/callhome

destination-profile full-txt-destination email-addr

[no] destination-profile full-txt-destination email-addr <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

email-addr

Add email addr

s0

Provide email address, example: jdow@xyz.com
Command Mode
  • /exec/configure/callhome

destination-profile full-txt-destination http

[no] destination-profile full-txt-destination http <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

http

Add http or https url

s0

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL
Command Mode
  • /exec/configure/callhome

destination-profile full-txt-destination message-level

destination-profile full-txt-destination message-level <i0>

Syntax Description

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

message-level

Callhome message level(0-lowest urgency, 9-highest urgency)

i0

Command Mode
  • /exec/configure/callhome

destination-profile full-txt-destination message-size

destination-profile full-txt-destination message-size <i0>

Syntax Description

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

message-size

Configure maximum message size (default 2500000)

i0

Provide maximum possible message size
Command Mode
  • /exec/configure/callhome

destination-profile full-txt-destination transport-method email

[no] destination-profile full-txt-destination transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

transport-method

Callhome message sending transport-method

email

email transport-method
Command Mode
  • /exec/configure/callhome

destination-profile full-txt-destination transport-method http

[no] destination-profile full-txt-destination transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

full-txt-destination

Configure destination profile for plain txt message

transport-method

Callhome message sending transport-method

http

http transport-method
Command Mode
  • /exec/configure/callhome

destination-profile short-txt-destination email-addr

[no] destination-profile short-txt-destination email-addr <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

email-addr

Add email addr

s0

Provide email address, example: jdow@xyz.com
Command Mode
  • /exec/configure/callhome

destination-profile short-txt-destination http

[no] destination-profile short-txt-destination http <s0>

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

http

Add http or https url

s0

Provide http or https url, example1: http://site.com/services/callserv example2: https://site2.com/serv/CALL
Command Mode
  • /exec/configure/callhome

destination-profile short-txt-destination message-level

destination-profile short-txt-destination message-level <i0>

Syntax Description

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

message-level

Callhome message level(0-lowest urgency, 9-highest urgency)

i0

Command Mode
  • /exec/configure/callhome

destination-profile short-txt-destination message-size

destination-profile short-txt-destination message-size <i0>

Syntax Description

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

message-size

Configure maximum message size (default 4000)

i0

Command Mode
  • /exec/configure/callhome

destination-profile short-txt-destination transport-method email

[no] destination-profile short-txt-destination transport-method email

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

transport-method

Callhome message sending transport-method

email

email transport-method
Command Mode
  • /exec/configure/callhome

destination-profile short-txt-destination transport-method http

[no] destination-profile short-txt-destination transport-method http

Syntax Description

no

(Optional) Negate a command or set its defaults

destination-profile

Configure destination profiles

short-txt-destination

Configure destination profile for short txt message

transport-method

Callhome message sending transport-method

http

http transport-method
Command Mode
  • /exec/configure/callhome

destination

[no] destination | destination <ipaddr>

Syntax Description

no

Negate a command or set its defaults

destination

destination of tunnel

ipaddr

ip address (A.B.C.D)
Command Mode
  • /exec/configure/if-te

destination

{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination }

Syntax Description

destination

Specify the destination address

ipaddr

Destination IP address for collector

use-vrf

(Optional) Optional VRF label

vrf_name

(Optional) VRF name

vrf-known-name

(Optional) Known VRF name
Command Mode
  • /exec/configure/nfm-exporter

device-group

{ device-group <name> } | { no device-group <name> }

Syntax Description

no

Negate a command or set its defaults

device-group

ITD device group

name

ITD device group name
Command Mode
  • /exec/configure/itd

diagnostic bootup level

[no] diagnostic bootup level

Syntax Description

no

Negate a command or set its defaults

diagnostic

Diagnostic commands

bootup

Configure Diagnostic for bootup

level

Select diagnostic level
Command Mode
  • /exec/configure

diagnostic eem action aggressive

[no] diagnostic eem action aggressive

Syntax Description

no

(Optional) Negate a command or set its defaults

diagnostic

Diagnostic commands

eem

Configure Diagnostic for eem

action

Select diagnostic action

aggressive

Take aggressive default actions
Command Mode
  • /exec/configure

diagnostic pss shrink

diagnostic pss shrink

Syntax Description

diagnostic

Diagnostic commands

pss

PSS command

shrink

compact the diag_port_lb PSS
Command Mode
  • /exec

diff-clean

diff-clean [ all-sessions ]

Syntax Description

diff-clean

remove temp files created by '| diff' filters

all-sessions

(Optional) remove '| diff' temp files from all sessions (past and present!) of current user
Command Mode
  • /exec

diff-clean all-users

diff-clean all-users

Syntax Description

diff-clean

remove temp files created by '| diff' filters

all-users

remove '| diff' temp files from all sessions (past and present!) of all users
Command Mode
  • /exec

diff

diff [ again | echo | -c [ <lines> ] | -b | -B | -i | -I <regexp> | -y | --left-column | -W <columns> | -q | -s ] +

Syntax Description

|

Pipe command output to filter

diff

show difference between current and previous invocation (creates temp files: remove them with 'diff-clean' command and dont use it on commands with big outputs, like 'show tech'!)

again

(Optional) dont create new file: use old ones, just change display options or add more filters

echo

(Optional) echo the current file (only effective if no old file)

-c

(Optional) set number of lines of context (default 3)

lines

(Optional) number of lines of context

-b

(Optional) Ignore changes in amount of white space

-B

(Optional) Ignore changes that just insert or delete blank lines

-i

(Optional) Ignore changes in case

-I

(Optional) Ignore changes that just insert or delete lines that match regexp

regexp

(Optional) regexp of lines to ignore

-y

(Optional) Use the side by side output format

--left-column

(Optional) Print only the left column of two common lines in side by side format

-W

(Optional) Use an output width of <columns> in side by side format

columns

(Optional) Use an output width of <columns> in side by side format

-q

(Optional) Report only whether the files differ, not the details of the differences

-s

(Optional) Report when two files are the same
Command Mode
  • /output

dir

dir [ <uri0> | <uri1> | <uri2> ]

Syntax Description

dir

list files in a directory

uri0

(Optional) Directory or filename

uri1

(Optional) Directory or filename on expansion flash

uri2

(Optional) Directory or filename on log flash
Command Mode
  • /exec

disable-connected-check

[ no | default ] disable-connected-check

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

disable-connected-check

Disable check for directly connected peer
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor-sess

disable-memory-alert-check

[no] disable-memory-alert-check

Syntax Description

no

(Optional) Negate a command or set its defaults

disable-memory-alert-check

Disables the system memory alert handling in BGP
Command Mode
  • /exec/configure/router-bgp

disable-peer-as-check

[ no | default ] disable-peer-as-check

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

disable-peer-as-check

Disable checking of peer AS-number while advertising
Command Mode
  • /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6 /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af

disable-peer-as-check

[ no | default ] disable-peer-as-check

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

disable-peer-as-check

Disable checking of peer AS-number while advertising
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn

disable-policy-batching

[no] disable-policy-batching [ { ipv4 | ipv6 } prefix-list <prfxlist-name> ]

Syntax Description

no

(Optional) Negate a command or set its defaults

disable-policy-batching

Disable batching evaluation of outbound policy for a peer

ipv4

(Optional) IPv4 address-family

ipv6

(Optional) IPv6 address-family

prefix-list

(Optional) Apply prefix-list

prfxlist-name

(Optional) Name of prefix-list
Command Mode
  • /exec/configure/router-bgp

disable

disable

Syntax Description

disable

disable callhome
Command Mode
  • /exec/configure/callhome

discard-route

[no] discard-route { external | internal }

Syntax Description

no

(Optional) Negate a command or set its defaults

discard-route

Install discard route

external

External route

internal

Internal route
Command Mode
  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

discard-route

[no] discard-route { external | internal }

Syntax Description

no

(Optional) Negate a command or set its defaults

discard-route

Install discard route

external

External route

internal

Internal route
Command Mode
  • /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

discovery

discovery { quick-start | hello { holdtime <link-hello-holdtime> | interval <link-hello-intvl> } | targeted-hello { accept [ from <pfx-list> ] | tgt-holdtime <tgt-hello-holdtime> | tgt-interval <tgt-hello-intvl> } | ignore-transport-address | omit-transport-address | spoofing } | no discovery { quick-start | hello { holdtime | interval } | targeted-hello { accept | tgt-holdtime | tgt-interval } | ignore-transport-address | omit-transport-address | spoofing }

Syntax Description

no

Negate a command or set its defaults

discovery

LDP discovery

quick-start

Enable quick LDP Hello transmissions on interface up

hello

LDP discovery Hello

interval

LDP discovery Hello interval

holdtime

LDP discovery Hello holdtime

link-hello-holdtime

Holdtime in seconds

link-hello-intvl

Hello interval in seconds

targeted-hello

LDP discovery Targeted Hello

accept

Accept targeted hellos

from

(Optional) Prefix list to specify acceptable targeted hello sources

pfx-list

(Optional) Name of prefix list

tgt-holdtime

LDP discovery Targeted Hello holdtime

tgt-hello-holdtime

Holdtime in seconds

tgt-interval

LDP discovery Targeted Hello interval

tgt-hello-intvl

Hello interval in seconds

ignore-transport-address

omit-transport-address

spoofing
Command Mode
  • /exec/configure/ldp

distance

distance <distance> | no distance [ <distance> ]

Syntax Description

no

Negate a command or set its defaults

distance

RIP administrative distance

distance

RIP administrative distance
Command Mode
  • /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common

distance

distance <admin-dist> | no distance [ <admin-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

OSPFv3 administrative distance

admin-dist

adminitrative distance value
Command Mode
  • /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6

distance

distance <ebgp-dist> <ibgp-dist> <local-dist> | no distance [ <ebgp-dist> <ibgp-dist> <local-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

Configure administrative distance

ebgp-dist

Distance for EBGP routes

ibgp-dist

Distance for IBGP routes

local-dist

Distance for local routes
Command Mode
  • /exec/configure/router-bgp/router-bgp-af

distance

{ { distance <int-distance> <ext-distance> } | { no distance [ <int-distance> <ext-distance> ] } }

Syntax Description

no

Negate a command or set its defaults

distance

Define an administrative distance

int-distance

Distance for internal routes

ext-distance

Distance for external routes
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

distance

distance <admin-dist> | no distance [ <admin-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

OSPF administrative distance

admin-dist

adminitrative distance value
Command Mode
  • /exec/configure/router-ospf /exec/configure/router-ospf/vrf

distance

distance <admin-dist> | no distance [ <admin-dist> ]

Syntax Description

no

Negate a command or set its defaults

distance

Administrative distance

admin-dist

Distance value
Command Mode
  • /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-common

distribute-list

[no] distribute-list { { route-map <map> } | { prefix-list <list> } } { in | out } <interface>

Syntax Description

no

(Optional) Negate a command or set its defaults

distribute-list

Filter networks in routing updates

route-map

Use a route-map for route filtering

map

Route-map name

prefix-list

Use a prefix-list for route filtering

list

Reference to prefix-list name

in

Filter incoming routing updates

out

Filter outgoing routing updates

interface

Interface name
Command Mode
  • /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

distribute

{ { distribute <src-level> into <dst-level> { { route-map { <map-name> | <rtr_pol_name> } } | all } } | { no distribute <src-level> into <dst-level> [ { route-map { <map-name> | <rtr_pol_name> } } | all ] } }

Syntax Description

no

Negate a command or set its defaults

distribute

Distribute routes between ISIS levels

src-level

Route-distribution between levels

dst-level

Route-distribution between levels

route-map

Route Map to constrain distribution

into

from level-n into level-m

map-name

A 'routing-rules' route-map name

rtr_pol_name

all

Distribute all level-n routes
Command Mode
  • /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-common

dns

[no] dns { <WORD> } { name-server { <hostname> | <ip-address> } } { [ source-ip { <source-ip-hostname> | <source-ip-address> } ] | [ source-port <src-port> ] } +

Syntax Description

no

(Optional)

source-ip

(Optional) source-port

src-port

(Optional)

dns

DNS Operation

WORD

Target IP Address or Hostname

name-server

Name Server

hostname

Destination hostname, broadcast disallowed

ip-address

Destination IP address, broadcast disallowed

source-ip-hostname

(Optional) source IP hostname, broadcast disallowed

source-ip-address

(Optional) source IP address, broadcast disallowed

source-port

(Optional) Source Port
Command Mode
  • /exec/configure/ip-sla

dont-capability-negotiate

[ no | default ] dont-capability-negotiate

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

dont-capability-negotiate

Don't negotiate capability with this neighbor
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor-sess

dos2nxos

dos2nxos <uri0>

Syntax Description

dos2nxos

DOS to NXOS text file format converter

uri0

Filename to be displayed
Command Mode
  • /exec

dot1q default dynamic

{ dot1q default dynamic } | { no dot1q default }

Syntax Description

no

Negate a command or set its defaults

dynamic

Dynamic Profile Map: Retrieve profile name from the external server

dot1q

Dot1Q Encapsulation

default

Default (wildcard). Match any dot1q when there is no specific dot1q mapping configured
Command Mode
  • /exec/configure/profile-map /exec/configure/profile-map-global

dot1x default

dot1x default

Syntax Description

dot1x

dot1x configuration commands
Command Mode
  • /exec/configure

dot1x default

dot1x default

Syntax Description

dot1x

dot1x configuration commands
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x mac-auth-bypass

dot1x mac-auth-bypass [ eap ] | no dot1x mac-auth-bypass

Syntax Description

no

Negate a command or set its defaults

dot1x

dot1x configuration commands

mac-auth-bypass

Configure Mac-Auth-Bypass

eap

(Optional) EAP Authentication
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x max-reauth-req

dot1x max-reauth-req <count> | no dot1x max-reauth-req

Syntax Description

dot1x

dot1x configuration commands

max-reauth-req

Maximum Re-authentication Attempts Before Failing

count

number of retries
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x max-req

dot1x max-req <count> | no dot1x max-req

Syntax Description

dot1x

dot1x configuration commands

max-req

Maximum Retries to Initiate Authentication

count

number of retries
Command Mode
  • /exec/configure

dot1x max-req

dot1x max-req <count> | no dot1x max-req

Syntax Description

dot1x

dot1x configuration commands

max-req

Maximum Retries to Initiate Authentication

count

number of retries
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x port-control

[no] dot1x port-control <port-control-value>

Syntax Description

dot1x

dot1x configuration commands

port-control

port control

port-control-value

set the port-control value
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x radius-accounting

[no] dot1x radius-accounting

Syntax Description

dot1x

dot1x configuration commands

radius-accounting

accounting messages to RADIUS
Command Mode
  • /exec/configure

dot1x re-authenticate

{ dot1x re-authenticate } | { dot1x re-authenticate interface <if> }

Syntax Description

dot1x

dot1x configuration commands

re-authenticate

Manually re-authenticate an Interface

if

target interface
Command Mode
  • /exec

dot1x re-authentication

[no] dot1x re-authentication

Syntax Description

dot1x

dot1x configuration commands

re-authentication

Enable or Disable Reauthentication for this port
Command Mode
  • /exec/configure

dot1x re-authentication

[no] dot1x re-authentication

Syntax Description

dot1x

dot1x configuration commands

re-authentication

Enable or Disable Reauthentication for this port
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x show credential

dot1x show credential <name>

Syntax Description

dot1x

dot1x configuration commands

credential

supplicant credential profile

name

profile name
Command Mode
  • /exec/configure/dot1x-cred

dot1x system-auth-control

[no] dot1x system-auth-control

Syntax Description

dot1x

dot1x configuration commands

system-auth-control

Enable or Disable SysAuthControl
Command Mode
  • /exec/configure

dot1x timeout quiet-period

dot1x timeout quiet-period <value> | no dot1x timeout quiet-period

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

quiet-period

Timeout For Retrying Authentication After Failed Authentication

value

time interval in seconds
Command Mode
  • /exec/configure

dot1x timeout quiet-period

dot1x timeout quiet-period <value> | no dot1x timeout quiet-period

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

quiet-period

Timeout For Retrying Authentication After Failed Authentication

value

time interval in seconds
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x timeout ratelimit-period

dot1x timeout ratelimit-period <value> | no dot1x timeout ratelimit-period

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

ratelimit-period

Rate Limit period for EAPOL-Start

value

time interval in seconds
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x timeout re-authperiod

dot1x timeout re-authperiod <value> | no dot1x timeout re-authperiod

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

re-authperiod

Timeout For Re-Authentication

value

time interval in seconds
Command Mode
  • /exec/configure

dot1x timeout re-authperiod

dot1x timeout re-authperiod <value> | no dot1x timeout re-authperiod

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

re-authperiod

Timeout For Re-Authentication

value

time interval in seconds
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x timeout server-timeout

dot1x timeout server-timeout <value> | no dot1x timeout server-timeout

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

server-timeout

Timeout for Radius Retries

value

time interval in seconds
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x timeout supp-timeout

dot1x timeout supp-timeout <value> | no dot1x timeout supp-timeout

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

supp-timeout

Timeout for Supplicant retries

value

time interval in seconds
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

dot1x timeout tx-period

dot1x timeout tx-period <value> | no dot1x timeout tx-period

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

tx-period

Timeout For Resending Requests To Supplicant

value

time interval in seconds
Command Mode
  • /exec/configure

dot1x timeout tx-period

dot1x timeout tx-period <value> | no dot1x timeout tx-period

Syntax Description

dot1x

dot1x configuration commands

timeout

Various Timeouts

tx-period

Timeout For Resending Requests To Supplicant

value

time interval in seconds
Command Mode
  • /exec/configure/if-eth-base /exec/configure/if-ethernet-all

down-bit-ignore

{ down-bit-ignore } | { no down-bit-ignore }

Syntax Description

no

Negate a command or set its defaults

down-bit-ignore

Configure a PE router to ignore the DN bit for network summary, external and NSSA external LSA
Command Mode
  • /exec/configure/router-ospf/vrf

downlink delay

downlink delay <ena-dis-flg> [ timeout <time-out> ] | no downlink delay

Syntax Description

no

Negate a command or set its defaults

downlink

Change downlink linkup time

delay

delay bringup of downlinks

ena-dis-flg

Enable/Disable downlink delay feature

timeout

(Optional) downlink ports enable delay in seconds

time-out

(Optional) Time out
Command Mode
  • /exec/configure

dscp

{ [ no ] dscp <dscp> | no dscp }

Syntax Description

dscp

Optional DSCP

dscp

Differentiated services codepoint value
Command Mode
  • /exec/configure/nfm-exporter

dual-active exclude interface-vlan

dual-active exclude interface-vlan <allow-vlans> | no dual-active exclude interface-vlan

Syntax Description

no

Negate a command or set its defaults

dual-active

Configuration when peer link is down but peer is alive

interface-vlan

Interface vlan configuration

exclude

Interface vlans to exclude from suspension when dual-active

allow-vlans

Set allowed interface vlans
Command Mode
  • /exec/configure/vpc-domain

duplex

duplex <duplex_mode> | no duplex [ <duplex_mode> ]

Syntax Description

no

Negate a command or set its defaults

duplex

Enter the port duplex mode

duplex_mode

Interface duplex mode
Command Mode
  • /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member

duplex

duplex <duplex_mode> | no duplex [ <duplex_mode> ]

Syntax Description

no

Negate a command or set its defaults

duplex

Enter the port duplex mode

duplex_mode

Interface duplex mode
Command Mode
  • /exec/configure/if-port-channel

duplex

duplex <duplex_mode> | no duplex [ <duplex_mode> ]

Syntax Description

no

Negate a command or set its defaults

duplex

Enter the port duplex mode

duplex_mode

Interface duplex mode
Command Mode
  • /exec/configure/if-mgmt-ether

duplicate-message throttle

[no] duplicate-message throttle

Syntax Description

no

(Optional) Negate a command or set its defaults

duplicate-message

Configure throttling of duplicate callhome alert messages

throttle

Enable throttling of duplicate callhome alert messages
Command Mode
  • /exec/configure/callhome

dynamic-capability

[ no | default ] dynamic-capability

Syntax Description

no

(Optional) Negate a command or set its defaults

default

(Optional) Inherit values from a peer template

dynamic-capability

Dynamic capability
Command Mode
  • /exec/configure/router-bgp/router-bgp-neighbor-sess

dynamic-med-interval

[no] dynamic-med-interval <sec>

Syntax Description

no

(Optional) Negate a command or set its defaults

dynamic-med-interval

Sets the interval for dampening of med changes

sec

Time interval in seconds
Command Mode
  • /exec/configure/router-bgp