Cisco Nexus 9000 Series NX-OS Command Reference (Configuration Commands), Release 7.0(3)I3(1)

l2rib dup-host-mac-detection

l2rib dup-host-mac-detection { default | <num-of-moves> <duration> }

Syntax Description


l2rib	Layer 2 routing information base
dup-host-mac-detection	Set Duplicate-Host-MAC-Detection parameters
default	Default parameters (5 moves in 180 secs)
num-of-moves	Number of host moves to be allowed
duration	Duplicate detection timeout in secs for host moves

Command Mode

/exec/configure

l2rib dup-host-mac-recovery

l2rib dup-host-mac-recovery { default | <timeout> <retry-count> | disable }

Syntax Description


l2rib	Layer 2 routing information base
dup-host-mac-recovery	Set Duplicate-Host-MAC-Recovery (Unfreeze) parameters
default	Default parameters (30 secs unfreeze time and 3 retries)
timeout	Unfreeze timeout (secs)
retry-count	Unfreeze retry count
disable	Disable duplicate host MAC recovery (is enabled by default)

Command Mode

/exec/configure

l2rib event-history

l2rib event-history { client-tbl | ead-pl | errors | mac | mac-ip | misc-obj | rmac | topology | tx-infra } size { default | medium | high | very-high }

Syntax Description


l2rib	Layer 2 routing information base
event-history	Set event-history size for L2RIB
client-tbl	L2RIB Client, Producer, Consumer Tables Event Logs
ead-pl	L2RIB EAD, Path-List Objects Event Logs
errors	L2RIB Error Logs
mac	L2RIB MAC Object Event Logs
mac-ip	L2RIB MAC Object Event Logs
misc-obj	L2RIB IMET, Flood-List, ARP-Signal, Peer ID, Startup-Routes Objects Event Logs
rmac	L2RIB Router MAC Object Event Logs
topology	L2RIB Topology Object Event Logs
tx-infra	L2RIB TxList, TxSend, TxThread Event Logs
size	Size
default	Default (Low)
medium	Medium
high	High
very-high	Very High

Command Mode

/exec/configure

label allocate global

[no] label allocate global { all-routes | host-routes | prefix-list <pfx-list> }

Syntax Description


no	(Optional) Negate a command or set its defaults
label	LDP label configuration
allocate	Allocate local labels
global	Specify default VPN Routing/Forwarding instance
all-routes	Allocate local labels for all routes
host-routes	Allocate local labels for host routes only (default)
prefix-list	Specify a prefix-list for local label filtering
pfx-list	IP prefix-list for destination prefixes

Command Mode

/exec/configure/ldp

lacp fast-select-hot-standby

lacp fast-select-hot-standby | no lacp fast-select-hot-standby

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
fast-select-hot-standby	Configure fast select for hot standby ports. Enabling this feature will allow fast selection of hot standby port when last active port in the port-channel is going down.

Command Mode

/exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p

lacp port-priority

lacp port-priority <port-pri> | no lacp port-priority

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
port-priority	Set LACP port priority
port-pri	Enter port priority

Command Mode

/exec/configure/if-eth-base /exec/configure/if-ethernet-all

lacp rapid-transition

lacp rapid-transition | no lacp rapid-transition

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
rapid-transition	Optimizes LACP timers for rapid transition from P->I, I->P state

Command Mode

/exec/configure

lacp rate

lacp rate <rate_type>

Syntax Description


lacp	Set LACP parameters for the interface
rate	Configure rate at which PDUs are sent by LACP
rate_type	Rate type

Command Mode

/exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp rate

[no] lacp rate

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
rate	Configure rate at which PDUs are sent by LACP

Command Mode

/exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch

lacp system-priority

lacp system-priority <sys-pri> | no lacp system-priority

Syntax Description


no	Negate a command or set its defaults
lacp	Set LACP parameters for the interface
system-priority	Set LACP system priority
sys-pri	Enter System Priority

Command Mode

/exec/configure

last

last [ <lines> ]

Syntax Description


\|	Pipe command output to filter
last	Display last lines
lines	(Optional) number of lines to print

Command Mode

/output

layer2-switched flow monitor

[no] layer2-switched flow monitor <monitorname> input [ sampler <samplername> ]

Syntax Description


layer2-switched	Configure L2 features
flow	NetFlow related commands
monitor	Apply a Flow Monitor to this interface
monitorname	Name of Flow Monitor
input	Apply Flow Monitor on input traffic
sampler	(Optional) Optional Sampler to apply to this Flow Monitor
samplername	(Optional) Name of Sampler

Command Mode

/exec/configure/if-switching

layer3 peer

layer3 peer | no layer3 peer

Syntax Description


no	Negate a command or set its defaults
layer3	Enable layer 3 functionality
peer	no change for TTL of packets destined to the peer

Command Mode

/exec/configure/vpc-domain

ldap-search-map

[no] ldap-search-map

Syntax Description


no	Negate a command or set its defaults
ldap-search-map	Set one of the configured search-map as active

Command Mode

/exec/configure/ldap

ldap-search-map

ldap-search-map <s0>

Syntax Description


ldap-search-map	Set one of the configured search-map as active
s0	Name of the search-map

Command Mode

/exec/configure/ldap

ldap-server deadtime

[no] ldap-server deadtime <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
deadtime	Global LDAP server deadtime period in seconds
i0	LDAP server deadtime period in minutes (default 0 mins -disabled)

Command Mode

/exec/configure

ldap-server host

[no] ldap-server host { <hostipname> } [ { enable-ssl | port <i1> [ timeout <i2> ] | rootDN <s0> [ password { 7 <s1> { { [ port1 <i3> [ timeout1 <i4> ] ] } | { [ timeout5 <i9> ] } } | <s2> { { [ port2 <i5> [ timeout2 <i6> ] ] } | { [ timeout4 <i8> ] } } } ] | timeout3 <i7> } ]

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
host	LDAP server's DNS name or IP address
hostipname	IPV4/IPV6 address or DNS name
enable-ssl	(Optional) LDAP server enable ssl
port	(Optional) LDAP server's port (default: global config)
i1	(Optional) port number
timeout	(Optional) LDAP server timeout period in seconds
i2	(Optional) LDAP server timeout in seconds (default: global config)
rootDN	(Optional) LDAP server root DN
s0	(Optional) root DN
password	(Optional) LDAP server root password
7	(Optional) LDAP root password (encrypted)
s1	(Optional) password (encrypted)
port1	(Optional) LDAP server's port (default: global config)
i3	(Optional) port number
timeout1	(Optional) LDAP server timeout period in seconds
i4	(Optional) LDAP server timeout in seconds (default: global config)
s2	(Optional) password (clear text)
port2	(Optional) LDAP server's port (default: global config)
i5	(Optional) port number
timeout2	(Optional) LDAP server timeout period in seconds
i6	(Optional) LDAP server timeout in seconds (default: global config)
timeout3	(Optional) LDAP server timeout period in seconds
i7	(Optional) LDAP server timeout in seconds (default: global config)
timeout4	(Optional) LDAP server timeout period in seconds
i8	(Optional) LDAP server timeout in seconds (default: global config)
timeout5	(Optional) LDAP server timeout period in seconds
i9	(Optional) LDAP server timeout in seconds (default: global config)

Command Mode

/exec/configure

ldap-server port

[no] ldap-server port <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
port	Global LDAP server's port (default 389)
i0	port number

Command Mode

/exec/configure

ldap-server timeout

[no] ldap-server timeout <i0>

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap-server	Configure LDAP related parameters
timeout	Global LDAP server timeout period in seconds
i0	LDAP server timeout period in seconds (default 5 sec)

Command Mode

/exec/configure

ldap search-map

[no] ldap search-map <s0>

Syntax Description


no	(Optional) Negate a command or set its defaults
ldap	Configure information about ldap
search-map	Configure the search-map
s0	Search Map Name

Command Mode

/exec/configure

license expiry check_interval

license expiry check_interval <i0>

Syntax Description


license	Enter the license configuration mode
expiry	Configure the expiry check interval
check_interval	Configure the expiry check interval
i0	Specify the license expiry check interval in seconds

Command Mode

/exec

license grace-period

[no] license grace-period

Syntax Description


no	(Optional) Negate a command or set its defaults
license	Modify license features
grace-period	Configure grace period support for licenses

Command Mode

/exec/configure

license grace-period days

license grace-period days <i0>

Syntax Description


license	Enter the license configuration mode
grace-period	Configure the grace period
days	Congigure the grace period in days
i0	Number of days

Command Mode

/exec

license grace-period seconds

license grace-period seconds <i0>

Syntax Description


license	Enter license configuration mode
grace-period	Configure the grace period
seconds	Configure the grace period in seconds
i0	Specify the grace period in seconds

Command Mode

/exec

license grace period

license grace period <i0>

Syntax Description


license	Enter the license configuration mode
grace	Configure the grace period
period	Specify the grace period in days
i0

Command Mode

/exec

license reserve count

[no] license reserve count <i0> package <license-feature> module <i1>

Syntax Description


no	(Optional) Negate a command or set its defaults
license	Display licensing information
reserve	Reserve the licenses for the specified module
count	Count of licenses to reserve
i0	Count of licenses
package	Name of the license package to reserve
license-feature	Name of the license package
module	Module number
i1	Module number

Command Mode

/exec/configure

limit-resource m4route-mem

{ limit-resource m4route-mem [ minimum { <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } } | { no limit-resource m4route-mem [ [ minimum { <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
m4route-mem	set ipv4 route memory limits
minimum	(Optional) minimum route memory to allocate
min	(Optional) minimum route memory value
min-hi	(Optional) minimum route memory value
maximum	maximum route memory to allocate
max-lo	maximum route memory value
max	maximum route memory value
max-hi	maximum route memory value
equal-to-min	maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource m6route-mem

{ limit-resource m6route-mem [ minimum { <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> } } | { no limit-resource m6route-mem [ [ minimum { <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
m6route-mem	set ipv6 route memory limits
minimum	(Optional) minimum route memory to allocate
min	(Optional) minimum route memory value
min-hi	(Optional) minimum route memory value
maximum	maximum route memory to allocate
max-lo	maximum route memory value
max	maximum route memory value
max-hi	maximum route memory value

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource module-type

{ limit-resource module-type <card-type> + } | { no limit-resource module-type }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
module-type	Controls which type of modules are allowed in this vdc
card-type	Allowed module types

Command Mode

/exec/configure/vdc

limit-resource monitor-session-erspan-dst minimum

{ limit-resource monitor-session-erspan-dst minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-erspan-dst [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


limit-resource	Resource configuration
monitor-session-erspan-dst	Monitor erspan destination session
minimum	minimum monitor erspan-dst session to allocate
min-val	minimum monitor erspan-dst session value
maximum	maximum monitor erspan-dst session to allocate
max-val	maximum monitor erspan-dst session value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session-inband-src minimum

{ limit-resource monitor-session-inband-src minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session-inband-src [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


limit-resource	Resource configuration
monitor-session-inband-src	Monitor inband source
minimum	minimum monitor inband source to allocate
min-val	minimum monitor inband source value
maximum	maximum monitor inband source to allocate
max-val	maximum monitor inband source value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource monitor-session minimum

{ limit-resource monitor-session minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource monitor-session [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


limit-resource	Resource configuration
monitor-session	Monitor local/erspan-source session
minimum	minimum monitor local session to allocate
min-val	minimum monitor local session value
maximum	maximum monitor local session to allocate
max-val	maximum monitor local session value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource port-channel minimum

limit-resource port-channel minimum <min-val> maximum { <max-val> | equal-to-min } | no limit-resource port-channel [ minimum <min-val> maximum { <max-val> | equal-to-min } ]

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
port-channel	set port-channel limits
minimum	minimum port-channels to allocate
min-val
maximum	maximum port-channels to allocate
max-val
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource u4route-mem

{ limit-resource u4route-mem [ minimum { <min-lo> | <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } } | { no limit-resource u4route-mem [ [ minimum { <min-lo> | <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
u4route-mem	set ipv4 route memory limits
minimum	(Optional) minimum route memory to allocate
min-lo	(Optional) minimum route memory value
min	(Optional) minimum route memory value
min-hi	(Optional) minimum route memory value
maximum	maximum route memory to allocate
max-lo	maximum route memory value
max	maximum route memory value
max-hi	maximum route memory value
equal-to-min	maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource u6route-mem

{ limit-resource u6route-mem [ minimum { <min-lo> | <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } } | { no limit-resource u6route-mem [ [ minimum { <min-lo> | <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
u6route-mem	set ipv6 route memory limits
minimum	(Optional) minimum route memory to allocate
min-lo	(Optional) minimum route memory value
min	(Optional) minimum route memory value
min	(Optional) minimum route memory value
min-hi	(Optional) minimum route memory value
maximum	maximum route memory to allocate
max-lo	maximum route memory value
max	maximum route memory value
max-hi	maximum route memory value
equal-to-min	maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource vlan minimum

{ limit-resource vlan minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resource vlan [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
vlan	set VLAN limits
minimum	minimum VLANs to allocate
min-val	minimum VLANs value
maximum	maximum VLANs to allocate
max-val	maximum VLANs value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

limit-resource vrf minimum

{ limit-resource vrf minimum <number1> maximum { <number2> | equal-to-min } } | { no limit-resource vrf [ minimum <number1> maximum { <number2> | equal-to-min } ] }

Syntax Description


no	Negate a command or set its defaults
limit-resource	Resource configuration
vrf	set vrf resource limits
minimum	minimum vrf resources to allocate
number1	minimum vrf resource value
maximum	maximum vrf resources to allocate
number2	maximum vrf resource value
equal-to-min	set maximum value equal to min

Command Mode

/exec/configure/vdc-template /exec/configure/vdc

line console

[no] line console

Syntax Description


no	(Optional) Negate a command or set its defaults
line	Configure a terminal line
console	Primary terminal line

Command Mode

/exec/configure

line console

[no] line console

Syntax Description


no	(Optional) Negate a command or set its defaults
line	Configure a terminal line
console	Primary terminal line

Command Mode

/exec/configure

line vty

Syntax Description


line	Configure a terminal line
vty	Virtual terminal line

Command Mode

/exec/configure

line vty

[no] line vty

Syntax Description


no	Negate a command or set its defaults
line	Configure a terminal line
vty	Virtual terminal line

Command Mode

/exec/configure

link-management timers

[no] link-management timers { bandwidth-hold | periodic-flooding } | link-management timers { bandwidth-hold <bw_seconds> | periodic-flooding <flood_seconds> }

Syntax Description


no	Negate a command or set its defaults
link-management	Link Management configuration
timers	Link Management timers configuration
bandwidth-hold	Link Management bandwidth hold timer
bw_seconds	seconds
periodic-flooding	Link Management periodic flooding interval
flood_seconds	seconds [0 to disable, minimum set to 30]

Command Mode

/exec/configure/te

link debounce

link debounce [ time <time_val> ] | no link debounce [ time <time_val> ]

Syntax Description


no	Negate a command or set its defaults
link	Configure link
debounce	Configure link debounce timer
time	(Optional) Link debounce time
time_val	(Optional) Timer value (in milliseconds)

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-sub

lisp-rig

{ lisp-rig | rig } [ instance-id <iid> ] { <hostname> | { <eid> | <eid6> } } to { <ddt-hostname> | { <ddt> | <ddt6> } }

Syntax Description


lisp-rig	LISP-DDT Referral Internet Groper
rig	LISP-DDT Referral Internet Groper
instance-id	(Optional) Instance-ID of VPN EID resides in
iid	(Optional) 24-bit instance-ID value
eid	RIG on a IPv4 Endpoint ID (EID)
hostname	DNS name for Endpoint ID (EID)
to	Where to send the Map-Request
ddt-hostname	DNS name for DDT-node
ddt	DDT-node IPv4 address to send Map-Request to

Command Mode

/exec

list

list [ <index> ]

Syntax Description


list	Re-list all or part of the explicit path entries
index	(Optional) List starting at entry index number

Command Mode

/exec/configure/te/expl-path

list

Syntax Description


list	Re-list all of the attribute list entries

Command Mode

/exec/configure/te/lsp-attr

listobject-boolean

listobject-boolean <object-id> not

Syntax Description


listobject-boolean	Configure Object as member of tracking list
object-id	Tracked object
not	Negate Up status

Command Mode

/exec/configure/tr-list-bool

listobject-weight

listobject-weight { <object-id> weight <weight-val> } | threshold-weight { weight-thresh { weightup <up-weight> [ weightdown <down-weight> ] | weightdown <down-weight> [ weightup <up-weight> ] } } | no threshold-weight weight-thresh

Syntax Description


no	Negate a command or set its defaults
listobject-weight	Configure Object as member of tracking list
object-id	Tracked Object
weight	Assign a weight to object
weight-val	Assign a weight to object
threshold-weight	Threshold parameters
weight-thresh	Weight threshold
weightup	Up threshold
up-weight	Up threshold weight
weightdown	(Optional) Down threshold
down-weight	(Optional) Down threshold weight

Command Mode

/exec/configure/tr-list-thrw

listobject

[no] listobject <object-id>

Syntax Description


no	(Optional) Negate a command or set its defaults
listobject	Configure Object as member of tracking list
object-id	Tracked Object

Command Mode

/exec/configure/tr-list-thrw /exec/configure/tr-list-thrp /exec/configure/tr-list-bool

lldp

[no] lldp { holdtime <i0> | reinit <i1> | timer <i2> | portid-subtype <i3> | tlv-select { management-address | port-description | port-vlan | system-capabilities | system-description | system-name | dcbxp } }

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure global LLDP parameters
holdtime	Specify the holdtime (in sec) to be sent in packets
i0	holdtime in sec
reinit	Delay (in sec) for LLDP initialisation on any interface
i1	reinit in sec
timer	Specify the rate at which LLDP packets are sent (in sec)
i2	rate of packets in sec
portid-subtype	config portid subtype for LLDP TLV and SNMP MIBs
i3	0: long interface name (default), 1: short interface name
tlv-select	Selection of LLDP to send
management-address	Management Address TLV
port-description	Port Description TLV
port-vlan	Port Vlan ID TLV
system-capabilities	System Capabilities TLV
system-description	System Description TLV
system-name	System Name TLV
dcbxp	DCBXP TLVs

Command Mode

/exec/configure

lldp eee

[no] lldp eee { rx_wake_time <i0> | tx_wake_time <i1> }

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure LLDP parameters
eee	Configure LLDP EEE parameters
rx_wake_time	Specify the EEE rx wake time
i0	EEE rx wake time
tx_wake_time	Specify the EEE tx wake time
i1	EEE tx wake time

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp receive

[no] lldp receive

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
receive	Enable LLDP reception on interface

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-select eee

[no] lldp tlv-select eee

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
tlv-select	Configure EEE parameter
eee	Enable/Disable LLDP EEE TLV

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-select management-address

[no] lldp tlv-select management-address { v4 | v6 }

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure global LLDP parameters
tlv-select	Selection of LLDP to send
management-address	Management Address TLV
v4	Management Address TLV v4
v6	Management Address TLV v6

Command Mode

/exec/configure

lldp tlv-set management-address

[no] lldp tlv-set management-address <ip-addr>

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
tlv-set	LLDP TLV configuration for interface
management-address	Management address to be sent in management-tlv of LLDPDU.
ip-addr	IP address in dotted decimal format i.i.i.i

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set management-address

[no] lldp tlv-set management-address <ipv6-addr> ipv6

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
tlv-set	LLDP TLV configuration for interface
management-address	Management address to be sent in management-tlv of LLDPDU.
ipv6	IPV6

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp tlv-set vlan

[no] lldp tlv-set vlan [ <vlan-id> ]

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
tlv-set	LLDP TLV configuration for interface
vlan	VLAN-id whose SVI IP address should be used as management adrress in management-tlv of LLDPDU. Default is native VLAN.
vlan-id	(Optional) vlan-id within range of 1-4094

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

lldp transmit

[no] lldp transmit

Syntax Description


no	(Optional) Negate a command or set its defaults
lldp	Configure Interface LLDP parameters
transmit	Enable LLDP transmission on interface

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether /exec/configure/if-eth-base /exec/configure/if-mgmt-ether

load-balance

[no] load-balance { [ method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst | ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | buckets <num> | mask-position <mask> ] + }

Syntax Description


no	(Optional) Negate a command or set its defaults
load-balance	ITD Loadbalance
method	(Optional) ITD Loadbalance method
src	(Optional) Source based parameters
dst	(Optional) Destination based parameters
ip	(Optional) IP
ip-l4port	(Optional) IP and L4 port
src-protocol	(Optional) Protocol
range	(Optional) Match only packets in the range of port numbers
src-x	(Optional)
src-y	(Optional)
ip-dst	(Optional) IP
dst-protocol	(Optional) Protocol
dst-x	(Optional)
dst-y	(Optional)
buckets	(Optional) Used to create the buckets for traffic distribution, and it should be in powers of 2
num	(Optional) Loadbalance bucket number
mask-position	(Optional) Loadbalance mask position
mask	(Optional) Loadbalance mask position number range 0-31 for IPv4

Command Mode

/exec/configure/itd

load-balancing

load-balancing <load-bal> | no load-balancing [ <load-bal> ]

Syntax Description


no	Negate a command or set its defaults
load-balancing	Load balancing method
load-bal	Load balancing method

Command Mode

/exec/configure/if-eth-any/glbp

load-interval

load-interval <interval> | no load-interval [ <interval1> ]

Syntax Description


no	Negate a command or set its defaults
load-interval	Specify interval for load calculation for an interface
interval	Load interval delay in seconds
interval1	(Optional) Load interval delay in seconds

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load-interval

load-interval [ counter <counter_val> ] <interval> | no load-interval [ counter <counter_val> ] [ <interval1> ]

Syntax Description


no	Negate a command or set its defaults
load-interval	Specify interval for load calculation for an interface
counter	(Optional) Specify counter for this load interval
interval	Load interval delay in seconds
counter_val	(Optional) Specify counter for this load interval
interval1	(Optional) Load interval delay in seconds

Command Mode

/exec/configure/if-vlan-common

load-interval counter

load-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]

Syntax Description


no	Negate a command or set its defaults
load-interval	Specify interval for load calculation for an interface
counter	Specify counter for this load interval
counter_val	Specify counter for this load interval
interval	Load interval delay in seconds
interval1	(Optional) Load interval delay in seconds

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel

load

load <uri0> [ <s0> ]

Syntax Description


load	Load system image
uri0	Enter image URI
s0	(Optional) Options

Command Mode

/exec

load

load <uri0>

Syntax Description


load	Load system image
uri0	Enter image URI

Command Mode

/exec

load

load <uri0> [ <s0> ]

Syntax Description


load	Load system image
uri0	Enter image URI
s0	(Optional) Options

Command Mode

/exec

local-as

local-as <asn> | no local-as [ <asn> ]

Syntax Description


no	Negate a command or set its defaults
local-as	Specify the local-as for this vrf
asn	AS number

Command Mode

/exec/configure/router-bgp/router-bgp-vrf

local-as

{ local-as <asn> [ no-prepend [ replace-as [ dual-as ] ] ] } | { { no | default } local-as [ <asn> ] }

Syntax Description


no	Negate a command or set its defaults
default	Inherit values from a peer template
local-as	Specify the local-as number for the eBGP neighbor
asn	Autonomous System Number
no-prepend	(Optional) Do not prepend the local-as number to updates from the eBGP neighbor
replace-as	(Optional) Prepend only the local-as number to updates to eBGP neighbor
dual-as	(Optional) Connect using either the local-as number or the real as

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor-sess

locator-led

[no] locator-led { chassis | module <module> | fan <fan_num> }

Syntax Description


no	(Optional) Negate a command or set its defaults
locator-led	blink locator led on device
chassis	blink chassis led
module	blink module led
module	please enter the module number
fan	blink Fan led
fan_num	fan number

Command Mode

/exec

lockdown

[no] lockdown

Syntax Description


no	(Optional) Negate a command or set its defaults
lockdown	Lockdown the LSP--disable reoptimization

Command Mode

/exec/configure/te/lsp-attr

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state
detail	(Optional) Notify all state changes

Command Mode

/exec/configure/router-ospf /exec/configure/router-ospf/vrf

log-adjacency-changes

[no] log-adjacency-changes [ detail ]

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state
detail	(Optional) Notify all state changes

Command Mode

/exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf

log-adjacency-changes

{ [ no ] log-adjacency-changes } | { [ no ] [ eigrp ] log-neighbor-changes }

Syntax Description


no	(Optional) Negate a command or set its defaults
eigrp	(Optional) EIGRP router configuration commands
log-adjacency-changes	Log changes in adjacency state
log-neighbor-changes	Enable/Disable IP-EIGRP neighbor logging

Command Mode

/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state

Command Mode

/exec/configure/otv-isis/otv-isis-vrf-common

log-adjacency-changes

[no] log-adjacency-changes

Syntax Description


no	(Optional) Negate a command or set its defaults
log-adjacency-changes	Log changes in adjacency state

Command Mode

/exec/configure/router-isis/router-isis-vrf-common

log-event-type

no ] [ eigrp ] log-event-type [ dual ] [ xmit ] [ transport ]

Syntax Description


no	(Optional) Negate a command or set its defaults
eigrp	(Optional) EIGRP router configuration commands
log-event-type	Set event types logged
dual	(Optional) Log DUAL events
xmit	(Optional) Log transmission events
transport	(Optional) Log transport events

Command Mode

/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

log-neighbor-changes

[no] log-neighbor-changes

Syntax Description


no	(Optional) Negate a command or set its defaults
log-neighbor-changes	Log a message for neighbor up/down event

Command Mode

/exec/configure/router-bgp/vrf-cmds

log-neighbor-changes

no | default ] log-neighbor-changes [ disable ]

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
log-neighbor-changes	Log message for neighbor up/down event
disable	(Optional) Disable logging of neighbor up/down event

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor-sess

log-neighbor-warnings

{ { [ eigrp ] log-neighbor-warnings [ <interval> ] } | { no [ eigrp ] log-neighbor-warnings [ <interval> ] } }

Syntax Description


no	Negate a command or set its defaults
eigrp	(Optional) EIGRP router configuration commands
log-neighbor-warnings	Enable/Disable IP-EIGRP neighbor warnings
interval	(Optional) Neighbor warning interval in seconds

Command Mode

/exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common

logging

[no] logging { lsp { path-errors | preemption | reservation-errors | setups | teardowns } | tunnel { lsp-selection | path change } } | logging { lsp { path-errors | preemption | reservation-errors | setups | teardowns } | tunnel { lsp-selection | path change } }

Syntax Description


no	Negate a command or set its defaults
logging	Trap logging configuration
lsp	LSP-specific traps logging configuration
path-errors	Log LSP Path Error traps
preemption	Log LSP Preemption traps
reservation-errors	Log LSP Reservation Error traps
setups	Log LSP Establishment Traps
teardowns	Log LSP Teardown Traps
tunnel	Tunnel-specific traps logging configuration
lsp-selection	Log Tunnel LSP Selection traps
path	Log Tunnel Path-related traps
change	Log Tunnel Path change traps

Command Mode

/exec/configure/te

logging

[no] logging { neighbor-changes |

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Enable LDP logging
neighbor-changes	Log LDP neighbor state changes

Command Mode

/exec/configure/ldp

logging abort

Syntax Description


logging	Modify message logging facilities
abort	Flushes cached data without committing and releases the lock

Command Mode

/exec/configure

logging clear_console

Syntax Description


logging	Exec logging commands
clear_console	Clear Console

Command Mode

/exec

logging distribute

[no] logging distribute

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
distribute	Enables/disables fabric distribution using cfs.

Command Mode

/exec/configure

logging drop threshold

logging drop threshold <threshold-in-packets> [ level <level-value> ] | [ no ] logging drop threshold [ <threshold-in-packets> [ level <level-value> ] ]

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	set logging for copp class
drop	logging for dropped packets
threshold	threshold value for dropped packets
level	(Optional) syslog level
level-value	(Optional) specify the logging level between 1-7

Command Mode

/exec/configure/pmap/class

logging event

[no] logging event { link-status | trunk-status } { enable | default }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
link-status	UPDOWN and CHANGE messages
trunk-status	TRUNK status messages
enable	To enable logging overriding port level configuration
default	default logging configuration used by interfaces not explicitly configured

Command Mode

/exec/configure

logging event port link-status

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port link-status

[no] logging event port link-status

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port link-status

logging event port link-status [ default ] | no logging event port link-status

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages
default	(Optional) Use the global default value

Command Mode

/exec/configure/if-port-channel /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-gig-ether-sub /exec/configure/if-loopback /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p

logging event port link-status default

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
link-status	UPDOWN and CHANGE messages
default	Use the global default value

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
trunk-status	TRUNK status messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status

[no] logging event port trunk-status

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
event	Interface events
port	Port level events
trunk-status	TRUNK status messages

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging event port trunk-status default

Syntax Description


logging	Configure logging for interface
event	Interface events
port	Port level events
trunk-status	TRUNK status messages
default	Use the global default value

Command Mode

/exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel

logging flush

Syntax Description


logging	Exec logging commands
flush	Flushing logging

Command Mode

/exec

logging invalid-username

[no] logging invalid-username

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	One Platform logging
invalid-username	Display invalid usernames in ONE-P log messages

Command Mode

/exec/configure/onep

logging level

logging level { keystore | sksd } <i0> | no logging level { keystore | sksd } [ <i0> ]

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
keystore	Keystore syslog level
sksd	Keystore/sksd syslog level
i0

Command Mode

/exec/configure

logging level ethpm

[no] logging level ethpm { link-up | link-down } <level>

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
level	Facility parameter for syslog messages
ethpm	Set level for ethpm syslog messages
link-up	Configure logging level for link up syslog messages
link-down	Configure logging level for link down syslog messages
level	Logging Level

Command Mode

/exec/configure

logging max_messages

logging max_messages <i0>

Syntax Description


logging	Exec logging commands
max_messages	Increase maximum syslogd message buffer size
i0

Command Mode

/exec

logging message interface type ethernet

logging message interface type ethernet <info> | no logging message interface type ethernet <info>

Syntax Description


no	Negate a command or set its defaults
logging	Configure logging for interface
message	Interface events
interface	Interface level events
type	Interface type
ethernet	Ethernet interfaces
info	Field Names to be added to interface syslog

Command Mode

/exec/configure

logging reconcile

logging reconcile { all [ force ] | files <i0> | vtys <i1> | dev <s0> }

Syntax Description


logging	Modify message logging facilities
reconcile	Reconcile the internal data structures in syslogd, only use in console connection when all VTYs are closed
all	Reconcile all VTY elements in Files array and VTY list - only supported in console
force	(Optional) Reconcile all VTY elements in Files array and VTY list - force to run in VTYs or console
files	Reconcile specific element in Files array
i0	Enter Files array index to reconcile
vtys	Reconcile specific element in VTY list
i1	Enter VTY list index to reconcile
dev	Reconcile specific dev elements in Files array and VTY list
s0	Enter the dev name to reconcile

Command Mode

/exec/configure

logging source-interface

{ logging source-interface <interface> | no logging source-interface }

Syntax Description


no	Negate a command or set its defaults
logging	Modify message logging facilities
source-interface	Enable Source-Interface for Remote Syslog Server
interface	Source interface name

Command Mode

/exec/configure

logging timestamp

[no] logging timestamp { microseconds | milliseconds | seconds }

Syntax Description


no	(Optional) Negate a command or set its defaults
logging	Modify message logging facilities
timestamp	Set logging timestamp granularity
microseconds	Timestamp in micro-seconds
milliseconds	Timestamp in milli-seconds
seconds	Timestamp in seconds (Default)

Command Mode

/exec/configure

login block-for

login block-for <i1> attempts <i2> within <i3>

Syntax Description


login	Enable secure login checking
block-for	Set quiet-mode active time period
i1	Time period in seconds
attempts	Set max number of fail attempts
i2	Fail attempts max value
within	Watch period for fail attempts
i3	Time period in seconds

Command Mode

/exec/configure

login block-for

[no] login block-for

Syntax Description


no	Negate a command or set its defaults
login	Enable secure login checking
block-for	Set quiet-mode active time period

Command Mode

/exec/configure

login quiet-mode

[no] login quiet-mode

Syntax Description


no	Negate a command or set its defaults
login	Enable secure login checking
quiet-mode	Set quiet-mode options

Command Mode

/exec/configure

login quiet-mode access-class

login quiet-mode access-class <access-list>

Syntax Description


login	Enable secure login checking
quiet-mode	Set quiet-mode options
access-class	Set access class
access-list	Access-list name

Command Mode

/exec/configure

logit

logit <log>

Syntax Description


logit	Add
log	Specify

Command Mode

/exec

logout-warning

{ logout-warning <i0> | no logout-warning [ <i0> ] }

Syntax Description


no	Negate a command or set its defaults
logout-warning	Configure logout warning
i0	Enter logout warning time in seconds

Command Mode

/exec/configure/line

low-memory exempt

[ no | default ] low-memory exempt

Syntax Description


no	(Optional) Negate a command or set its defaults
default	(Optional) Inherit values from a peer template
low-memory	Behaviour
exempt	Do

Command Mode

/exec/configure/router-bgp/router-bgp-neighbor-sess

lshow

Syntax Description


lshow	display this instance of credential

Command Mode

/exec/configure/dot1x-cred

lshow

Syntax Description


lshow	local show: displays config of current interface

Command Mode

/exec/configure/if-igp

lsp-gen-interval

lsp-gen-interval <level> <max-wait> [ <initial-wait> <second-wait> ] | no lsp-gen-interval <level> <max-wait> [ <initial-wait> <second-wait> ]

Syntax Description


no	Negate a command or set its defaults
lsp-gen-interval	Configure LSP generation interval
level	IS-IS level
max-wait	Maximum wait between trigger and LSP generation (milli-secs)
initial-wait	(Optional) Initial wait between trigger and LSP generation (milli-secs)
second-wait	(Optional) Second wait used in LSP generation (milli-secs) during backoff

Command Mode

/exec/configure/router-isis/router-isis-vrf-common

lsp-mtu

lsp-mtu <mtu> | no lsp-mtu [ <mtu> ]

Syntax Description


no	Negate a command or set its defaults
lsp-mtu	Set LSP MTU
mtu	Maximum LSP size in bytes

Command Mode

/exec/configure/otv-isis/otv-isis-vrf-common

lsp-mtu

lsp-mtu <mtu> | no lsp-mtu [ <mtu> ]

Syntax Description


no	Negate a command or set its defaults
lsp-mtu	Set LSP MTU
mtu	Maximum LSP size in bytes

Command Mode

/exec/configure/router-isis/router-isis-vrf-common

lsp attributes

[no] lsp attributes <name>

Syntax Description


no	(Optional) Negate a command or set its defaults
lsp	Configure LSP parameters
attributes	Configure LSP attributes
name	Name of LSP attribute list

Command Mode

/exec/configure/te

Bias-Free Language

Results

Chapter: L Commands

L Commands

l2rib dup-host-mac-detection

l2rib dup-host-mac-recovery

l2rib event-history

label allocate global

lacp fast-select-hot-standby

lacp port-priority

lacp rapid-transition

lacp rate

lacp rate

lacp system-priority

last

layer2-switched flow monitor

layer3 peer

ldap-search-map

ldap-search-map

ldap-server deadtime

ldap-server host

ldap-server port

ldap-server timeout

ldap search-map

license expiry check_interval

license grace-period

license grace-period days

license grace-period seconds

license grace period

license reserve count

limit-resource m4route-mem

limit-resource m6route-mem

limit-resource module-type

limit-resource monitor-session-erspan-dst minimum

limit-resource monitor-session-inband-src minimum

limit-resource monitor-session minimum

limit-resource port-channel minimum

limit-resource u4route-mem

limit-resource u6route-mem

limit-resource vlan minimum

limit-resource vrf minimum

line console

line console

line vty

line vty

link-management timers

link debounce

lisp-rig

list

list

listobject-boolean

listobject-weight

listobject

lldp

lldp eee

lldp receive

lldp tlv-select eee

lldp tlv-select management-address

lldp tlv-set management-address

lldp tlv-set management-address

lldp tlv-set vlan

lldp transmit

load-balance

load-balancing

load-interval

load-interval

load-interval counter

load

load

load

local-as

local-as

locator-led

lockdown

log-adjacency-changes

log-adjacency-changes

log-adjacency-changes

log-adjacency-changes

log-adjacency-changes