Cisco ONS SONET TL1 Command Guide, Release 10.x.x

<TAP>

The test access point number. The TAP number must be an integer with a range of 1 to 999. It is a string.

Note This command only supports changing the mode for a single TAP number at a time.

<MD>

The test access mode. (SPLTE, SPLTF, LOOPE, and LOOPF require an external quasi-random signal [QRS] input signal.) Single facility access digroup (FAD) test access does not support MONEF, SPLTEF, and SPLTAB modes.

The parameter type is test access mode (TACC_MODE).

• LOOPE

Splits both the A and B paths. Connect the line incoming from the E direction to the line outgoing in the E direction, and connect this looped configuration to the FAD. The line outgoing in the F direction will have a QRS connected, and the line incoming from the F direction will be terminated by the nominal characteristic impedance of the line. Intrusive test access mode.

• LOOPF

Splits both the A and B paths. Connect the line incoming from F direction to the line outgoing in the F direction, and connect this looped configuration to the FAD. The line outgoing in the E direction will have a QRS connected, and the line incoming from the E direction will be terminated by the nominal characteristic impedance of the line. Intrusive test access mode.

• MONE

Indicates that a monitor connection will be provided from the FAD to the A transmission path of the accessed circuit.

• MONEF

Indicates that a monitor connection will be provided for the following:

• From the FAD1 to a dual FAD (DFAD), or from the odd pair of a facility access path (FAP) to the A transmission path
• From the FAD2 of the same DFAD or the even pair of a FAP, to the B transmission path of the accessed circuit

• MONF

Indicates that a monitor connection will be provided from the FAD to the B transmission path of the accessed circuit.

• SPLTA

Indicates that a connection will be provided from both the E and F sides of the A transmission path of the circuit under test to the FAD and split the A transmission path. Intrusive test access mode.

• SPLTB

Indicates that a connection will be provided from both the E and F sides of the B transmission path of the circuit under test to the FAD and split the B transmission path. Intrusive test access mode.

• SPLTE

Splits both the A and B paths and connect the E side of the accessed circuit to the FAD. The line outgoing in the F direction will have a QRS connected, the line incoming from the F direction will have a QRS connected, and the line incoming from the E direction will be terminated by the nominal characteristic impedance of the line. Intrusive test access mode.

• SPLTEF

Splits both the A and B paths, and connect the E side of the accessed circuit to FAD1 and the F side to FAD2. Intrusive test access mode.

• SPLTF

Splits both the A and B paths, and connect the F side of the accessed circuit to the FAD. The line outgoing in the E direction will have a QRS connected, the line incoming in the E direction will have a QRS connected, and the line incoming from the E direction will be terminated by the nominal characteristic impedance of the line. Intrusive test access mode.

<SRC>

The source access identifier from the “EQPT” section.

<EQPTTYPE>

The equipment type to be upgraded. The parameter type is EQUIPMENT_TYPE.

• 10GE-XP

(ONS 15454) 2 x 10 Gbps. muxponder/L2 ethernet switch card

• 100G-LC-C

100G-LC-C card

• 100G-CK-C

100G-CK-C card

• 10X10G-LC

10X10G-LC card

• CFP-LC

CFP-LC card

• AR-MXP

Any rate muxponder

• AR-XP

Any rate xponder

• AR-XPE

Any rate enhanced xponder.

• 16-WXC-FS

16-WXC-FS card.

• 15216-MD-40-EVEN

Thermal Multiplex/Demultiplex Passive Unit, spaced at 50 GHz on even grid

• 15216-MD-40-ODD

Thermal Multiplex/Demultiplex Passive Unit, spaced at 50 GHz on odd grid

• 15216-MD-ID-50

Thermal Interleaver Passive Unit, spaced at 50 GHz grid

• 15216-FLD4-30-3

Edge 4-Ch Bi-Directional OADM Module 1530.33 to 1532.68.

• 15216-FLD4-33-4

Edge 4-Ch Bi-Directional OADM Module 1533.47 to 1535.82.

• 15216-FLD4-36-6

Edge 4-Ch Bi-Directional OADM Module 1536.61 to 1538.98.

• 15216-FLD4-39-7

Edge 4-Ch Bi-Directional OADM Module 1539.77 to 1542.14.

• 15216-FLD4-42-9

Edge 4-Ch Bi-Directional OADM Module 1542.94 to 1545.32.

• 15216-FLD4-46-1

Edge 4-Ch Bi-Directional OADM Module 1546.12 to 1548.51.

• 15216-FLD4-49-3

Edge 4-Ch Bi-Directional OADM Module 1549.32 to 1551.72.

• 15216-FLD4-52-5

Edge 4-Ch Bi-Directional OADM Module 1552.52 to 1554.94.

• 15216-FLD4-55-7

Edge 4-Ch Bi-Directional OADM Module 1555.75 to 1558.17.

• 15216-FLD4-58-9

Edge 4-Ch Bi-Directional OADM Module 1558.98 to 1561.42.

• 32DMX-L

3- channel demultiplexer for L-band

• 32WSS-L

32-channel wavelength switch selector for L-band

• 40-MXP-C

40 Gbit/Sec Multirate Muxponder

• 40-SMR1-C

The single module 40-channel ROADM on C-band

• 40-SMR2-C

The single module 40-channel ROADM with EDFA on C-band

• 40-TXP-C

40 Gigabits per second Multirate Transponder

• 80-WXC-C

80-channel wavelength cross-connect spaced at 100 GHz grid

• AD-1B

OADM 1-Band Filter

• AD-1C

OADM 1-Channel Filter

• AD-2C

OADM 2-Channel Filter

• AD-4B

OADM 4-Band Filter

• AD-4C

OADM 4-Channel Filter

• AICI

AIC-I card

• AIP

Alarm Indication Panel

• ALM-PWR

Alarm Power

• ASAP-4

ASAP carrier card with four PIM slots

• BP

The backplane of the NE

• CE-100T-8

8-port 100T card

• CE-1000-4

4-port GIGE mapper card

• CRFT-TMG

Craft Timing

• DCC

Data Communications Channel

• DCU

Dispersion Compensation Unit

• DMX-32

Optical DMX 32 Channels

• DS3i-N-12

DS3i-N-12 card

• E1

E1 card

• E1-42

42-port E1 card

• E1000T-2

2-port interface card supporting 1000BaseT Ethernet facilities

• E100T-12

12-port interface card supporting 100BaseT Ethernet facilities

• E100T-4

Four-port interface card supporting 100BaseT Ethernet facilities

• E1N

E1N card

• E3

E3 card

• EDRA-1-26

EDRA-1-26 amplifier

• EDRA-1-35

EDRA-1-35 amplifier

• EDRA-2-26

EDRA-2-26 amplifier

• EDRA-2-35

EDRA-2-35 amplifier

• FBGDCU-1157

• FBGDCU-1322

• FBGDCU-165

• FBGDCU-1653

• FBGDCU-1983

• FBGDCU-331

• FBGDCU-496

• FBGDCU-661

• FBGDCU-826

• FBGDCU-992

• FILLER_CARD

Filler card

• FMEC-155E-1TO1

The equipment type for FMEC STM1E12 card

• FMEC-155E-1TO3

The equipment type for FMEC STM1E12 card with 1:3 protection

• FMEC-155E-UNPROT

The equipment type for FMEC STM1E12 card without protection

• FMEC-SMZ-E1

FMEC card corresponding to E1 card

• FMEC-SMZ-E3

FMEC card corresponding to E3 card

• FTA

Fan Tray of the NE

• FTA1

Fan Tray 1 of the NE

• FTA2

Fan Tray 2 of the NE

• G1K-4

G1K-4 card

• MD-4

Optical Multiplexer/Demultiplexer with 4 Channels

• MD-48-CM

• MD-48-EVEN

• MD-48-ODD

• MESH-PP-SMR

The passive unit Patch Panel device used to connect upto four 40-SMR2-C cards

• MF-16AD-CFS

16-channels - 1 direction, colorless, omnidirectional add/drop unit.

• MF-4x4-COFS

4-channels, 4-directions, colorless, omnidirectional add/drop unit.

• MF-AST-EDFA

MF-AST-EDFA unit

• MF-DEG-5

5-degrees mesh patch panel

• MF-MPO-8LC

MPO to 8-LC adapter

• MF-UPG-4

4-degrees upgrade module

• ML100X-8

8-port 100X card with optical interface

• ML-100T-8

8-port 100T card with optical interface

• MMU

Multiring mesh upgrade unit

• MS-ISC-100T

Fast Ethernet switch card used for internal shelf connection

• MUX-32

Optical MUX 32 Channels

• MXP-2.5G-10G

10G (4 * 2.5G) Muxponder card

• MXP-MR-10DME

10 Gbps datamux with enhanced FEC

• OPT-AMP-L

Optical preamplifier for L-band

• OPT-BST

Optical booster amplifier

• OPT-BST-L

Optical booster for L-band

• OPT-EDFA-17

MAL-less EDFA Optical Amplifier - C-band - 17dB Gain

• OPT-EDFA-24

MAL-less EDFA Optical Amplifier - C-band - 24dB Gain

• OPT-PRE

Optical Preamplifier

• OPT-RAMP-C

Raman pump amplifier C-band

• OPT-RAMP-CE

An extended version of Raman pump amplifier

• OPT-RAMP-COP

Raman COP card.

• OPT-RAMP-CTP

Raman CTP card.

• OPT-RAMP-E

Raman pump amplifier E-band

• OSC-CSM

Optical Service Channel with Combiner/Separator Module

• OSCM

Optical Service Channel Module

• OTU2-XP

A 4x10G transponder that is capable to operate with multiple bit rates - 10G FC, 10GE, and OC192/STM64

• PIM-4

Pluggable interface module with 4 PPM slots

• PP-4-SMR

Patch-Panel, 4 degrees, for SMR cards

• PP-MESH-4

Patch-Panel, 4 degrees

• PP-MESH-8

Patch-Panel, 8 degrees

• PPM-1

Pluggable port module with 1-port SFP module

• PSM

Protection Service Module card

• PTF-4

Fabric card.

• PTM-4

Line card.

• PTSA

CPT 50 panel.

• PTSYS- Fan-Out-Group

PTSYS Fan-Out-Group.

• SHELF

Shelf entity

• STM4

An interface card that supports one or more STM4 (622 Mbps) optical facilities

• STM4-4

A four port STM4 card

• STM4-IR-1

An interface card that supports one intermediate range STM4 (622 Mbps) optical facilities

• STM4-LR-1

An interface card that supports one long range STM4 (622 Mbps) optical facilities

• STM4-SR-1

An interface card that supports one short range STM4 (622 Mbps) optical facilities

• STM64-4

A four port STM64 card

• STM64-LR-1

An interface card that supports one or more STM64 optical facilities

• STM1

An interface card that supports multiple STM1 (155 Mbps) optical facilities

• STM1-IR-4

An interface card that supports four intermediate range STM1 (155 Mbps) optical facilities

• STM1-SR-4

An interface card that supports four short range STM1 (155 Mbps) optical facilities

• STM1ATM-IR-6

An interface card that supports six intermediate range STM1 (155 Mbps) ATM optical fibers

• STM1IR-STM1SH-
  1310-8

An STM1 card which has 8 ports over the lower speed slot with XC-VXL-10G/XC-VXL-2.5G

• STM1POS-SR-4

An interface card that supports four short range STM1 (155 Mbps) POS optical facilities

• STM16

An interface card that supports one or more STM16 (10 Gbps) optical facilities

• STM16-AS-1

An interface card that supports one short range OC-48 (10 Gbps) optical facilities that can be provisioned in any I/O slot

• STM16-ELR-1

An interface card that supports one short range STM16 (2.5 Gbps) optical facility

• STM16-IR-1

An interface card that supports one intermediate range STM16 (10 Gbps) optical facility

• STM16-LR-1

An interface card that supports one long range STM16 (10 Gbps) optical facility

• STM16-SR-1

An interface card that supports one short range STM16 (10 Gbps) optical facilities

• TCC

Timing, Communications, and Control card

• TDC-CC

Coarse tunable dispersion compensation unit

• TDC-FC

Fine tunable dispersion compensation unit

• TXP-MR-10G

10G Multirate Transponder card

• TXP-MR-2.5G

Multirate 2.5G Unprotected

• TXPP-MR-2.5G

Multirate 2.5G Protected

• UNKNOWN

Unknown equipment type

• UNPROVISIONED

Unprovisioned equipment type

• WSE

Wire Speed Encryption (WSE) card

• XC-VXC-10G

XC-VXC-10G cross-connect card

• XCVXL-10G

XC-VXL-10G cross-connect card

• XCVXL-2.5G

XC-VXL-2.5G cross-connect card

<PPMTYPE>

Identifies the pluggable port module type. This parameter can take only one value.

• PPM-1

Single-port PPM

<PPMNUM>

Identifies the pluggable port module number. This parameter is an Integer.

• 1

PPM No. 1

• 2

PPM No. 2

• 3

PPM No. 3

• 4

PPM No. 4

• 5

PPM No. 5

• 6

PPM No. 6

• 7

PPM No. 7

• 8

PPM No. 8

• 9

PPM No. 9

• 10

PPM No. 10

• 11

PPM No. 11

• 12

PPM No. 12

<PORTNUM>

Identifies the port number, which is used on the entity port with PPM. This para meter is an integer.

• 1

Port No. 1

<PORTRATE>

Identifies the port rate, which is used to specify the port rate of the multi-rate card.

• STM1

STM-1 rate

• STM4

STM-4 rate

• STM16

STM-16 rate