show call history fax through show debug condition

show call history fax

To display the call history table for fax transmissions, use the show call history fax command in user EXEC or privileged EXEC mode.

show call history fax [brief [id identifier] | compact [duration {less | more} time] | id identifier | last number ]

Syntax Description

brief

(Optional) Displays a truncated version of the call history table.

id identifier

(Optional) Displays only the call with the specified identifier. Range is a hex value from 1 to FFFF.

compact

(Optional) Displays a compact version.

duration time

(Optional) Displays history information for calls that are longer or shorter than a specified time value. The arguments and keywords are as follows:

  • less--Displays calls shorter than the value in the time argument.

  • more--Displays calls longer than the value in the time argument.

  • time --Elapsed time, in seconds. Range is from 1 to 2147483647.

last number

(Optional) Displays the last calls connected, where the number of calls that appear is defined by the number argument. Range is from 1 to 100 .

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Release

Modification

11.3(1)T

This command was introduced on the Cisco 3600 series.

12.0(3)XG

This command was implemented for Voice over Frame Relay (VoFR) on the Cisco 2600 series and Cisco 3600 series.

12.0(4)XJ

This command was modified for store-and-forward fax.

12.0(4)T

This command was modified. The brief keyword was added, and the command was implemented on the Cisco 7200 series.

12.0(7)XK

This command was modified. The brief keyword was implemented on the Cisco MC3810.

12.1(2)T

This command was integrated into Cisco IOS Release 12.1(2)T.

12.1(5)XM

This command was implemented on the Cisco AS5800.

12.1(5)XM2

This command was implemented on the Cisco AS5350 and Cisco AS5400.

12.2(2)XA

This command was modified. The output of this command was modified to indicate whether the call in question has been established using Annex E.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 was not included in this release.

12.2(11)T

This command was implemented on the Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850.

12.3(1)

This command was modified. The following fields were added: FaxRelayMaxJitterBufDepth, FaxRelayJitterBufOverFlow, FaxRelayHSmodulation, and FaxRelayNumberOfPages.

12.3(14)T

This command was modified. T.38 fax relay call statistics were made available to Call Detail Records (CDRs) through vendor-specific attributes (VSAs) and added to the call log.

12.4(15)T

This command was modified. The Port and BearerChannel display fields were added to the TELE call leg record of the command output.

12.4(16)

This command was modified. The Port and BearerChannel display fields were added to the TELE call leg record of the command output.

12.4(22)T

This command was modified. Command output was updated to show IPv6 information.

Usage Guidelines

This command displays a call-history table that contains a list of fax calls connected through the router in descending time order. The maximum number of calls contained in the table can be set to a number from 0 to 500 using the dial-control-mib command in global configuration mode. The default maximum number of table entries is 50. Each call record is aged out of the table after a configurable number of minutes has elapsed, also specified by the dial-control-mib command. The default timer value is 15 minutes.

You can display subsets of the call history table by using specific keywords. To display the last calls connected through this router, use the keyword last , and define the number of calls to be displayed with the number argument.

To display a truncated version of the call history table, use the brief keyword.

This command applies to both on-ramp and off-ramp store-and-forward fax functions.

Examples

The following is sample output from the show call history fax command:


Router# show call history fax
Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 0
MGCP call-legs: 0
Total call-legs: 1
GENERIC:
SetupTime=590180 ms
Index=2
PeerAddress=4085452930
PeerSubAddress=
PeerId=81
PeerIfIndex=221
LogicalIfIndex=145
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=59389
DisconnectTime=68204
CallDuration=00:01:28
CallOrigin=2
ReleaseSource=1
ChargedUnits=0
InfoType=fax
TransmitPackets=295
TransmitBytes=5292
ReceivePackets=2967
ReceiveBytes=82110
TELE:
ConnectionId=[0xD9ACDFF1 0x9F5D11D7 0x8002CF18 0xB9C3632]
IncomingConnectionId=[0xD9ACDFF1 0x9F5D11D7 0x8002CF18 0xB9C3632]
CallID=2
Port=3/0/0 (2)
BearerChannel=3/0/0.1
TxDuration=28960 ms
VoiceTxDuration=0 ms
FaxTxDuration=28960 ms
FaxRate=voice bps
FaxRelayMaxJitterBufDepth  = 0 ms
FaxRelayJitterBufOverFlow = 0
FaxRelayHSmodulation = 0
FaxRelayNumberOfPages = 0
NoiseLevel=-120
ACOMLevel=127
SessionTarget=
ImgPages=0
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=4085550130
OriginalCallingOctet=0x0
OriginalCalledNumber=52930
OriginalCalledOctet=0xE9
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0xFF
TranslatedCallingNumber=4085550130
TranslatedCallingOctet=0x0
TranslatedCalledNumber=52930
TranslatedCalledOctet=0xE9
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwReceivedCalledNumber=52930
GwReceivedCalledOctet3=0xE9
GwReceivedCallingNumber=4085550130
GwReceivedCallingOctet3=0x0
GwReceivedCallingOctet3a=0x80

The table below provides an alphabetical listing of the fields displayed in the output of the show call history fax command and a description of each field.

Table 1. show call history fax Field Descriptions

Field

Description

ACOM Level

Current ACOM level for this call. ACOM is the combined loss achieved by the echo canceler, which is the sum of the Echo Return Loss, Echo Return Loss Enhancement, and nonlinear processing loss for the call.

BearerChannel

Identification of the bearer channel carrying the call.

Buffer Drain Events

Total number of jitter buffer drain events.

Buffer Fill Events

Total number of jitter buffer fill events.

CallDuration

Length of the call, in hours, minutes, and seconds, hh:mm:ss.

CallerName

Voice port station name string.

CallOrigin

Call origin: answer or originate.

CallState

Current state of the call.

ChargedUnits

Total number of charging units that apply to this peer since system startup. The unit of measure for this field is hundredths of second.

CodecBytes

Payload size, in bytes, for the codec used.

CoderTypeRate

Negotiated coder rate. This value specifies the send rate of voice or fax compression to its associated call leg for this call.

ConnectionId

Global call identifier for this gateway call.

ConnectTime

Time, in milliseconds (ms), at which the call was connected.

Consecutive-packets-lost Events

Total number of consecutive (two or more) packet-loss events.

Corrected packet-loss Events

Total number of packet-loss events that were corrected using the RFC 2198 method.

Dial-Peer

Tag of the dial peer sending this call.

DisconnectCause

Cause code for the reason this call was disconnected.

DisconnectText

Descriptive text explaining the reason for the disconnect.

DisconnectTime

Time, in ms, when this call was disconnected.

EchoCancellerMaxReflector=64

The location of the largest reflector, in ms. The reflector size does not exceed the configured echo path capacity. For example, if 32 ms is configured, the reflector does not report beyond 32 ms.

ERLLevel

Current Echo Return Loss (ERL) level for this call.

FaxTxDuration

Duration of fax transmission from this peer to the voice gateway for this call. You can derive the Fax Utilization Rate by dividing the FaxTxDuration value by the TxDuration value.

FaxRelayJitterBufOverFlow

Count of number of network jitter buffer overflows (number of packets). These packets are equivalent to lost packets.

FaxRelayMaxJitterBufDepth

Maximum depth of jitter buffer (in ms).

FaxRelayHSmodulation

Most recent high-speed modulation used.

FaxRelayNumberOfPages

Number of pages transmitted.

GapFillWithInterpolation

Duration of a voice signal played out with a signal synthesized from parameters, or samples of data preceding and following in time because voice data was lost or not received in time from the voice gateway for this call.

GapFillWithRedundancy

Duration of a voice signal played out with a signal synthesized from available redundancy parameters because voice data was lost or not received in time from the voice gateway for this call.

GapFillWithPrediction

Duration of the voice signal played out with signal synthesized from parameters, or samples of data preceding in time, because voice data was lost or not received in time from the voice gateway for this call. Examples of such pullout are frame-eraser and frame-concealment strategies in G.729 and G.723.1 compression algorithms.

GapFillWithSilence

Duration of a voice signal replaced with silence because voice data was lost or not received in time for this call.

GENERIC

Generic or common parameters, that is, parameters that are common for VoIP and telephony call legs.

GwReceivedCalledNumber, GwReceivedCalledOctet3, GwReceivedCallingNumber, GwReceivedCallingOctet3, GwReceivedCallingOctet3a

Call information received at the gateway.

H323 call-legs

Total H.323 call legs for which call records are available.

HiWaterPlayoutDelay

High-water-mark Voice Playout FIFO Delay during this call.

ImgPages

The fax pages that have been processed.

Incoming ConnectionId

The incoming_GUID. It can be different with ConnectionId (GUID) when there is a long_pound or blast_call feature involved. In those cases, incoming_GUID is unique for all the subcalls that have been generated, and GUID is different for each subcall.

Index

Dial peer identification number.

InfoActivity

Active information transfer activity state for this call.

InfoType

Information type for this call; for example, voice or fax.

InSignalLevel

Active input signal level from the telephony interface used by this call.

Last Buffer Drain/Fill Event

Elapsed time since the last jitter buffer drain or fill event, in seconds.

Local UUID

Unique identifier generated from the originating user agent.

LogicalIfIndex

Index number of the logical interface for this call.

LoWaterPlayoutDelay

Low-water-mark Voice Playout FIFO Delay during this call.

LowerIFName

Physical lower interface information. Appears only if the medium is ATM, Frame Relay (FR), or High-Level Data Link Control (HDLC).

Media

Medium over which the call is carried. If the call is carried over the (telephone) access side, the entry is TELE. If the call is carried over the voice network side, the entry is either ATM, FR, or HDLC.

Modem passthrough signaling method in use

Indicates that this is a modem pass-through call and that named signaling events (NSEs)--a Cisco-proprietary version of named telephone events in RFC 2833--are used for signaling codec upspeed. The upspeed method is the method used to dynamically change the codec type and speed to meet network conditions. This means that you might move to a faster codec when you have both voice and data calls and then slow down when there is only voice traffic.

NoiseLevel

Active noise level for this call.

OnTimeRvPlayout

Duration of voice playout from data received on time for this call. Derive the Total Voice Playout Duration for Active Voice by adding the OnTimeRvPlayout value to the GapFill values.

OriginalCallingNumber, OriginalCalling Octet, OriginalCalledNumber, OriginalCalledOctet, OriginalRedirectCalledNumber, OriginalRedirectCalledOctet

Original call information regarding calling, called, and redirect numbers, as well as octet-3s. Octet-3s are information elements (IEs) of Q.931 that include type of number, numbering plan indicator, presentation indicator, and redirect reason information.

OutSignalLevel

Active output signal level to the telephony interface used by this call.

PeerAddress

Destination pattern or number associated with this peer.

PeerId

ID value of the peer table entry to which this call was made.

PeerIfIndex

Voice port index number for this peer. For ISDN media, this would be the index number of the B channel used for this call.

PeerSubAddress

Subaddress when this call is connected.

Percent Packet Loss

Total percent packet loss.

Port

Identification of the voice port carrying the call.

ReceiveBytes

Number of bytes received by the peer during this call.

ReceiveDelay

Average Playout FIFO Delay plus the Decoder Delay during this voice call.

ReceivePackets

Number of packets received by this peer during this call.

ReleaseSource

Number value of the release source.

RemoteIPAddress

Remote system IP address for the VoIP call.

RemoteUDPPort

Remote system User Datagram Protocol (UDP) listener port to which voice packets are sent.

Remote UUID

Unique identifier generated from the terminating user agent.

RoundTripDelay

Voice packet round-trip delay between the local and remote systems on the IP backbone for this call.

SelectedQoS

Selected Resource Reservation Protocol (RSVP) quality of service (QoS) for this call.

SessionProtocol

Session protocol used for an Internet call between the local and remote routers through the IP backbone.

SessionTarget

Session target of the peer used for this call.

SetupTime

Value of the system UpTime, in ms, when the call associated with this entry was started.

SignalingType

Signaling type for this call; for example, channel-associated signaling (CAS) or common-channel signaling (CCS).

SIP call-legs

Total SIP call legs for which call records are available.

Telephony call-legs

Total telephony call legs for which call records are available.

Time between Buffer Drain/Fills

Minimum and maximum durations between jitter buffer drain or fill events, in seconds.

TranslatedCallingNumber, TranslatedCallingOctet, TranslatedCalledNumber, TranslatedCalledOctet, TranslatedRedirectCalled Number, TranslatedRedirectCalledOctet

Translated call information.

TransmitBytes

Number of bytes sent by this peer during this call.

TransmitPackets

Number of packets sent by this peer during this call.

TxDuration

The length of the call. Appears only if the medium is TELE.

VAD

Whether voice activation detection (VAD) was enabled for this call.

VoiceTxDuration

Duration of voice transmission from this peer to the voice gateway for this call. Derive the Voice Utilization Rate by dividing the VoiceTxDuration value by the TxDuration value.

The following is sample output from the show call history fax brief command:


Router# show call history fax brief
<ID>: <start>hs.<index> +<connect> +<disc> pid:<peer_id> <direction> <addr>
 tx:<packets>/<bytes> rx:<packets>/<bytes> <disc-cause>(<text>)
 IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late>
  delay:<last>/<min>/<max>ms <codec>
 Telephony <int>: tx:<tot>/<voice>/<fax>ms <codec> noise:<lvl>dBm acom:<lvl>dBm
2    : 5996450hs.25 +-1 +3802 pid:100 Answer 408
 tx:0/0 rx:0/0 1F  (T30 T1 EOM timeout)
 Telephony : tx:38020/38020/0ms g729r8 noise:0dBm acom:0dBm
2    : 5996752hs.26 +-1 +3500 pid:110 Originate uut1@linux2.allegro.com
 tx:0/0 rx:0/0 3F  (The e-mail was not sent correctly. Remote SMTP server said: 354 )
 IP 14.0.0.1 AcceptedMime:0 DiscardedMime:0
3    : 6447851hs.27 +1111 +3616 pid:310 Originate 576341.
 tx:11/14419 rx:0/0 10  (Normal connection)
 Telephony : tx:36160/11110/25050ms g729r8 noise:115dBm acom:-14dBm
3    : 6447780hs.28 +1182 +4516 pid:0 Answer
 tx:0/0 rx:0/0 10  (normal call clearing.)
 IP 0.0.0.0 AcceptedMime:0 DiscardedMime:0
4    : 6464816hs.29 +1050 +3555 pid:310 Originate 576341.
 tx:11/14413 rx:0/0 10  (Normal connection)
 Telephony : tx:35550/10500/25050ms g729r8 noise:115dBm acom:-14dBm
4    : 6464748hs.30 +1118 +4517 pid:0 Answer
 tx:0/0 rx:0/0 10  (normal call clearing.)
 IP 0.0.0.0 AcceptedMime:0 DiscardedMime:0
5    : 6507900hs.31 +1158 +2392 pid:100 Answer 4085763413
 tx:0/0 rx:3/3224 10  (Normal connection)
 Telephony : tx:23920/11580/12340ms g729r8 noise:0dBm acom:0dBm
5    : 6508152hs.32 +1727 +2140 pid:110 Originate uut1@linux2.allegro.com
 tx:0/2754 rx:0/0 3F  (service or option not available, unspecified)
 IP 14.0.0.4 AcceptedMime:0 DiscardedMime:0
6    : 6517176hs.33 +1079 +3571 pid:310 Originate 576341.
 tx:11/14447 rx:0/0 10  (Normal connection)
 Telephony : tx:35710/10790/24920ms g729r8 noise:115dBm acom:-14dBm
6    : 6517106hs.34 +1149 +4517 pid:0 Answer
 tx:0/0 rx:0/0 10  (normal call clearing.)
 IP 0.0.0.0 AcceptedMime:0 DiscardedMime:0
7    : 6567382hs.35 +1054 +3550 pid:310 Originate 576341.
 tx:11/14411 rx:0/0 10  (Normal connection)
 Telephony : tx:35500/10540/24960ms g729r8 noise:115dBm acom:-14dBm
7    : 6567308hs.36 +1128 +4517 pid:0 Answer
tx:0/0 rx:0/0 10  (normal call clearing.)
 IP 0.0.0.0 AcceptedMime:0 DiscardedMime:0

The following example shows output for the show call history fax command with the T.38 Fax Relay statistics:


Router# show call history fax
Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 0
MGCP call-legs: 0
Total call-legs: 1
GENERIC:
SetupTime=9872460 ms
Index=8
PeerAddress=41023
PeerSubAddress=
PeerId=1
PeerIfIndex=242
LogicalIfIndex=180
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=9875610 ms
DisconnectTime=9936000 ms
CallDuration=00:01:00 sec
CallOrigin=2
ReleaseSource=1
ChargedUnits=0
InfoType=fax
TransmitPackets=268
TransmitBytes=4477
ReceivePackets=1650
ReceiveBytes=66882
TELE:
ConnectionId=[0xD6635DD5 0x9FA411D8 0x8005000A 0xF4107CA0]
IncomingConnectionId=[0xD6635DD5 0x9FA411D8 0x8005000A 0xF4107CA0]
CallID=7
Port=3/0/0:0 (7)
BearerChannel=3/0/0.8
TxDuration=6170 ms
VoiceTxDuration=0 ms
FaxTxDuration=0 ms
FaxRate=disable bps
FaxRelayMaxJitterBufDepth=560 ms
FaxRelayJitterBufOverFlow=0
FaxRelayMostRecentHSmodulation=V.17/short/14400
FaxRelayNumberOfPages=1
FaxRelayInitHSmodulation=V.17/long/14400
FaxRelayDirection=Transmit
FaxRelayPktLossConceal=0
FaxRelayEcmStatus=ENABLED
FaxRelayEncapProtocol=T.38 (UDPTL)
FaxRelayNsfCountryCode=Japan
FaxRelayNsfManufCode=0031B8EE80C48511DD0D0000DDDD0000DDDD000000000000000022ED00B0A400
FaxRelayFaxSuccess=Success
NoiseLevel=0
ACOMLevel=0
SessionTarget=
ImgPages=0
CallerName=Analog 41023
CallerIDBlocked=False
OriginalCallingNumber=
OriginalCallingOctet=0x80
OriginalCalledNumber=41021
OriginalCalledOctet=0xA1
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0xFF
TranslatedCallingNumber=41023
TranslatedCallingOctet=0x80
TranslatedCalledNumber=41021
TranslatedCalledOctet=0xA1
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwReceivedCalledNumber=41021
GwReceivedCalledOctet3=0xA1

The table below describes the fields not shown in the table above.

Table 2. show call history fax Field Descriptions

Field

Description

FaxRelayDirection

Direction of fax relay.

FaxRelayEcmStatus

Fax relay error correction mode status.

FaxRelayEncapProtocol

Fax relay encapsulation protocol.

FaxRelayFaxSuccess

Fax relay success.

FaxRelayInitHSmodulation

Fax relay initial high speed modulation.

FaxRelayMostRecentHSmodulation

Fax relay most recent high speed modulation.

FaxRelayNsfCountryCode

Fax relay Nonstandard Facilities (NSF) country code.

FaxRelayNsfManufCode

Fax relay NSF manufacturers code.

FaxRelayPktLossConceal

Fax relay packet loss conceal.

show call history media

To display the call history table for media calls, use the show call history media command in user EXEC or privileged EXEC mode.

show call history media [ [brief] [id identifier] | compact [duration {less | more} seconds] | last number]

Syntax Description

brief

(Optional) Displays a truncated version of the call history table.

id identifier

(Optional) Displays only the call with the specified identifier . The range is from 1 to FFFF.

compact

(Optional) Displays a compact version of the call history table.

duration

(Optional) Displays the call history for the specified time duration.

less

Displays the call history for shorter duration calls.

more

Displays the call history for longer duration calls.

seconds

Time, in seconds. The range is from 1 to 2147483647.

last number

(Optional) Displays the last calls connected, where the number of calls that appear is defined by the number argument. The range is from 1 to 100 .

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Release

Modification

12.4(15)T

This command was introduced.

Usage Guidelines

This command displays a call-history table that contains a list of media calls connected through the router in descending time order. The maximum number of calls contained in the table can be set to a number from 0 to 500 using the dial-control-mib command in global configuration mode. The default maximum number of table entries is 50. Each call record is aged out of the table after a configurable number of minutes has elapsed, also specified by the dial-control-mib command. The default timer value is 15 minutes.

You can display subsets of the call history table by using specific keywords. To display the last calls connected through this router, use the last keyword, and define the number of calls to be displayed with the number argument.

To display a truncated version of the call history table, use the brief keyword.

When a media call is active, you can display its statistics by using the show call active media command.

Examples

The following is sample output from the show call history media command:


Router# show call history media
Telephony call-legs: 0
SIP call-legs: 0
H323 call-legs: 0
Call agent controlled call-legs: 0
Media call-legs: 4
Total call-legs: 4
GENERIC:
SetupTime=308530 ms
Index=4
PeerAddress=sip:mrcpv2ASRServer@10.5.18.224:5060
PeerSubAddress=
PeerId=2234
PeerIfIndex=184
LogicalIfIndex=0
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=309440 ms
DisconnectTime=320100 ms
CallDuration=00:00:10 sec
CallOrigin=1
ReleaseSource=7
ChargedUnits=0
InfoType=speech
TransmitPackets=237
TransmitBytes=37920
ReceivePackets=0
ReceiveBytes=0
VOIP:
ConnectionId[0x2FB5B737 0xC3511DB 0x8005000B 0x5FDA0EF4]
IncomingConnectionId[0x2FB5B737 0xC3511DB 0x8005000B 0x5FDA0EF4]
CallID=14
RemoteIPAddress=10.5.18.224
RemoteUDPPort=10002
RemoteSignallingIPAddress=10.5.18.224
RemoteSignallingPort=5060
RemoteMediaIPAddress=10.5.18.224
RemoteMediaPort=10002
SRTP = off
TextRelay = off
Fallback Icpif=0
Fallback Loss=0
Fallback Delay=0
RoundTripDelay=0 ms
SelectedQoS=best-effort
tx_DtmfRelay=rtp-nte
FastConnect=FALSE
AnnexE=FALSE
Separate H245 Connection=FALSE
H245 Tunneling=FALSE
SessionProtocol=sipv2
ProtocolCallId=2FBDA670-C3511DB-8015C48C-6A894889@10.5.14.2
SessionTarget=10.5.18.224
OnTimeRvPlayout=3000
GapFillWithSilence=0 ms
GapFillWithPrediction=0 ms
GapFillWithInterpolation=2740 ms
GapFillWithRedundancy=0 ms
HiWaterPlayoutDelay=100 ms
LoWaterPlayoutDelay=40 ms
Source tg label=test5
ReceiveDelay=90 ms
LostPackets=0
EarlyPackets=0
LatePackets=0
VAD = disabled
CoderTypeRate=g711ulaw
CodecBytes=160
cvVoIPCallHistoryIcpif=16
MediaSetting=flow-around
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=
OriginalCallingOctet=0x0
OriginalCalledNumber=
OriginalCalledOctet=0x0
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0x0
TranslatedCallingNumber=555-0100
TranslatedCallingOctet=0x21
TranslatedCalledNumber=
TranslatedCalledOctet=0xC1
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwOutpulsedCallingNumber=555-0101
GwOutpulsedCallingOctet3=0x21
GwOutpulsedCallingOctet3a=0x81
MediaInactiveDetected=no
MediaInactiveTimestamp=
MediaControlReceived=
LongDurationCallDetected=no
LongDurationCallTimerStamp=
LongDurationCallDuration=
Username=
GENERIC:
SetupTime=308520 ms
Index=5
PeerAddress=sip:mrcpv2TTSServer@10.5.18.224:5060
PeerSubAddress=
PeerId=2235
PeerIfIndex=185
LogicalIfIndex=0
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=309370 ms
DisconnectTime=320100 ms
CallDuration=00:00:10 sec
CallOrigin=1
ReleaseSource=7
ChargedUnits=0
InfoType=speech
TransmitPackets=0
TransmitBytes=0
ReceivePackets=551
ReceiveBytes=88160
VOIP:
ConnectionId[0x2FB5B737 0xC3511DB 0x8005000B 0x5FDA0EF4]
IncomingConnectionId[0x2FB5B737 0xC3511DB 0x8005000B 0x5FDA0EF4]
CallID=13
RemoteIPAddress=10.5.18.224
RemoteUDPPort=10000
RemoteSignallingIPAddress=10.5.18.224
RemoteSignallingPort=5060
RemoteMediaIPAddress=10.5.18.224
RemoteMediaPort=10000
SRTP = off
TextRelay = off
Fallback Icpif=0
Fallback Loss=0
Fallback Delay=0
RoundTripDelay=0 ms
SelectedQoS=best-effort
tx_DtmfRelay=rtp-nte
FastConnect=FALSE
AnnexE=FALSE
Separate H245 Connection=FALSE
H245 Tunneling=FALSE
SessionProtocol=sipv2
ProtocolCallId=2FBC6E20-C3511DB-8013C48C-6A894889@10.5.14.2
SessionTarget=10.5.18.224
OnTimeRvPlayout=7000
GapFillWithSilence=0 ms
GapFillWithPrediction=0 ms
GapFillWithInterpolation=2740 ms
GapFillWithRedundancy=0 ms
HiWaterPlayoutDelay=100 ms
LoWaterPlayoutDelay=40 ms
Source tg label=test5
ReceiveDelay=95 ms
LostPackets=0
EarlyPackets=0
LatePackets=0
VAD = disabled
CoderTypeRate=g711ulaw
CodecBytes=160
cvVoIPCallHistoryIcpif=16
MediaSetting=flow-around
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=
OriginalCallingOctet=0x0
OriginalCalledNumber=
OriginalCalledOctet=0x0
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0x0
TranslatedCallingNumber=555-0102
TranslatedCallingOctet=0x21
TranslatedCalledNumber=
TranslatedCalledOctet=0xC1
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwOutpulsedCallingNumber=555-0103
GwOutpulsedCallingOctet3=0x21
GwOutpulsedCallingOctet3a=0x81
MediaInactiveDetected=no
MediaInactiveTimestamp=
MediaControlReceived=
LongDurationCallDetected=no
LongDurationCallTimerStamp=
LongDurationCallDuration=
Username=
GENERIC:
SetupTime=408050 ms
Index=7
PeerAddress=sip:mrcpv2ASRServer@10.5.18.224:5060
PeerSubAddress=
PeerId=2234
PeerIfIndex=184
LogicalIfIndex=0
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=408160 ms
DisconnectTime=426260 ms
CallDuration=00:00:18 sec
CallOrigin=1
ReleaseSource=7
ChargedUnits=0
InfoType=speech
TransmitPackets=598
TransmitBytes=95680
ReceivePackets=0
ReceiveBytes=0
VOIP:
ConnectionId[0x6B02FC0C 0xC3511DB 0x8006000B 0x5FDA0EF4]
IncomingConnectionId[0x6B02FC0C 0xC3511DB 0x8006000B 0x5FDA0EF4]
CallID=19
RemoteIPAddress=10.5.18.224
RemoteUDPPort=10002
RemoteSignallingIPAddress=10.5.18.224
RemoteSignallingPort=5060
RemoteMediaIPAddress=10.5.18.224
RemoteMediaPort=10002
SRTP = off
TextRelay = off
Fallback Icpif=0
Fallback Loss=0
Fallback Delay=0
RoundTripDelay=0 ms
SelectedQoS=best-effort
tx_DtmfRelay=rtp-nte
FastConnect=FALSE
AnnexE=FALSE
Separate H245 Connection=FALSE
H245 Tunneling=FALSE
SessionProtocol=sipv2
ProtocolCallId=6B0E94CD-C3511DB-801DC48C-6A894889@10.5.14.2
SessionTarget=10.5.18.224
OnTimeRvPlayout=11000
GapFillWithSilence=0 ms
GapFillWithPrediction=0 ms
GapFillWithInterpolation=9560 ms
GapFillWithRedundancy=0 ms
HiWaterPlayoutDelay=100 ms
LoWaterPlayoutDelay=55 ms
Source tg label=test5
ReceiveDelay=100 ms
LostPackets=0
EarlyPackets=0
LatePackets=0
VAD = disabled
CoderTypeRate=g711ulaw
CodecBytes=160
cvVoIPCallHistoryIcpif=16
MediaSetting=flow-around
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=
OriginalCallingOctet=0x0
OriginalCalledNumber=
OriginalCalledOctet=0x0
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0x0
TranslatedCallingNumber=555-0100
TranslatedCallingOctet=0x21
TranslatedCalledNumber=
TranslatedCalledOctet=0xC1
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwOutpulsedCallingNumber=555-0101
GwOutpulsedCallingOctet3=0x21
GwOutpulsedCallingOctet3a=0x81
MediaInactiveDetected=no
MediaInactiveTimestamp=
MediaControlReceived=
LongDurationCallDetected=no
LongDurationCallTimerStamp=
LongDurationCallDuration=
Username=
GENERIC:
SetupTime=408040 ms
Index=8
PeerAddress=sip:mrcpv2TTSServer@10.5.18.224:5060
PeerSubAddress=
PeerId=2235
PeerIfIndex=185
LogicalIfIndex=0
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=408130 ms
DisconnectTime=426260 ms
CallDuration=00:00:18 sec
CallOrigin=1
ReleaseSource=7
ChargedUnits=0
InfoType=speech
TransmitPackets=0
TransmitBytes=0
ReceivePackets=911
ReceiveBytes=145760
VOIP:
ConnectionId[0x6B02FC0C 0xC3511DB 0x8006000B 0x5FDA0EF4]
IncomingConnectionId[0x6B02FC0C 0xC3511DB 0x8006000B 0x5FDA0EF4]
CallID=18
RemoteIPAddress=10.5.18.224
RemoteUDPPort=10000
RemoteSignallingIPAddress=10.5.18.224
RemoteSignallingPort=5060
RemoteMediaIPAddress=10.5.18.224
RemoteMediaPort=10000
SRTP = off
TextRelay = off
Fallback Icpif=0
Fallback Loss=0
Fallback Delay=0
RoundTripDelay=0 ms
SelectedQoS=best-effort
tx_DtmfRelay=rtp-nte
FastConnect=FALSE
AnnexE=FALSE
Separate H245 Connection=FALSE
H245 Tunneling=FALSE
SessionProtocol=sipv2
ProtocolCallId=6B0CC055-C3511DB-801BC48C-6A894889@10.5.14.2
SessionTarget=10.5.18.224
OnTimeRvPlayout=9000
GapFillWithSilence=0 ms
GapFillWithPrediction=0 ms
GapFillWithInterpolation=9560 ms
GapFillWithRedundancy=0 ms
HiWaterPlayoutDelay=100 ms
LoWaterPlayoutDelay=55 ms
Source tg label=test5
ReceiveDelay=100 ms
LostPackets=0
EarlyPackets=0
LatePackets=0
VAD = disabled
CoderTypeRate=g711ulaw
CodecBytes=160
cvVoIPCallHistoryIcpif=16
MediaSetting=flow-around
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=
OriginalCallingOctet=0x0
OriginalCalledNumber=
OriginalCalledOctet=0x0
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0x0
TranslatedCallingNumber=555-0100
TranslatedCallingOctet=0x21
TranslatedCalledNumber=
TranslatedCalledOctet=0xC1
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwOutpulsedCallingNumber=555-0101
GwOutpulsedCallingOctet3=0x21
GwOutpulsedCallingOctet3a=0x81
MediaInactiveDetected=no
MediaInactiveTimestamp=
MediaControlReceived=
LongDurationCallDetected=no
LongDurationCallTimerStamp=
LongDurationCallDuration=
Username=

The table below describes the significant fields shown in the display, in alphabetical order.

Table 3. show call history media Field Descriptions

Field

Description

CallDuration

Length of the call, in hours, minutes, and seconds, hh:mm:ss.

CallOrigin

Call origin: not answer or originate.

ChargedUnits

Total number of charging units that apply to this peer since system startup. The unit of measure for this field is hundredths of second.

CodecBytes

Payload size, in bytes, for the codec used.

CoderTypeRate

Negotiated coder rate. This value specifies the send rate of voice or fax compression to its associated call leg for this call.

ConnectionId

Global call identifier for this gateway call.

ConnectTime

Time, in ms, during which the call was connected.

GapFillWithInterpolation

Duration, in ms, of a voice signal played out with a signal synthesized from parameters, or samples of data preceding and following in time because voice data was lost or not received in time from the voice gateway for this call.

GapFillWithRedundancy

Duration, in ms, of a voice signal played out with a signal synthesized from available redundancy parameters because voice data was lost or not received in time from the voice gateway for this call.

GapFillWithPrediction

Duration, in ms, of the voice signal played out with a signal synthesized from parameters, or samples of data preceding in time, because voice data was lost or not received in time from the voice gateway for this call. Examples of such pullout are frame-eraser and frame-concealment strategies in G.729 and G.723.1 compression algorithms.

GapFillWithSilence

Duration, in ms, of a voice signal replaced with silence because voice data was lost or not received in time for this call.

GENERIC

Generic or common parameters; that is, parameters that are common for VoIP and telephony call legs.

H323 call-legs

Total H.323 call legs for which call records are available.

HiWaterPlayoutDelay

High-water-mark voice playout first in first out (FIFO) Delay during this call, in ms.

Index

Dial peer identification number.

InfoType

Information type for this call; for example, voice, speech, or fax.

LogicalIfIndex

Index number of the logical interface for this call.

LoWaterPlayoutDelay

Low-water-mark voice playout FIFO delay during this call, in ms.

OnTimeRvPlayout

Duration of voice playout from data received on time for this call. Derive the Total Voice Playout Duration for Active Voice by adding the OnTimeRvPlayout value to the GapFill values.

PeerAddress

Destination pattern or number associated with this peer.

PeerId

ID value of the peer table entry to which this call was made.

PeerIfIndex

Voice port index number for this peer. For ISDN media, this would be the index number of the B channel used for this call.

PeerSubAddress

Subaddress when this call is connected.

ReceiveBytes

Number of bytes received by the peer during this call.

ReceiveDelay

Average playout FIFO delay plus the decoder delay during this voice call, in ms.

ReceivePackets

Number of packets received by this peer during this call.

ReleaseSource

Number value of the release source.

RemoteIPAddress

Remote system IP address for the VoIP call.

RemoteUDPPort

Remote system User Datagram Protocol (UDP) listener port to which voice packets are sent.

RoundTripDelay

Voice packet round-trip delay, in ms, between the local and remote systems on the IP backbone for this call.

SelectedQoS

Selected Resource Reservation Protocol (RSVP) quality of service (QoS) for this call.

SessionProtocol

Session protocol used for an Internet call between the local and remote routers through the IP backbone.

SessionTarget

Session target of the peer used for this call.

SetupTime

Value of the system UpTime, in ms, when the call associated with this entry was started.

SIP call-legs

Total Session Initiation Protocol (SIP) call legs for which call records are available.

Telephony call-legs

Total telephony call legs for which call records are available.

TransmitBytes

Number of bytes sent by this peer during this call.

TransmitPackets

Number of packets sent by this peer during this call.

VAD

Whether voice activation detection (VAD) was enabled for this call.

show call history stats

To display the statistics of call history, use show call history stats command in privileged EXEC mode.

show call history stats { connected table | cps { details | table } | short-duration

Syntax Description

connected

Displays call statistics for connected calls.

table

(Optional) Displays call statistics for connected calls in tabular format.

cps

Displays call statistics in calls handled per second format.

details

Displays call statistics in calls handled per second format including call-leg rate.

table

Displays call statistics in calls handled per second format including call-leg rate in tabular format

short-duration

Displays the call statistics for short-duration calls. By default, any call with total duration less than 5 seconds is considered as a short duration call. You can change the default value using Management Information Base (MIB).

Command Modes

Privileged EXEC (#)

Command History

Release Modification

Cisco IOS XE Release 3.8

This command was introduced.

Usage Guidelines

Use show call history stats connected command to display statistics of connected calls in graphical format.

Device#show call history stats connected 

                                                                
   10                                                             
    9                                                             
    8                                                             
    7                                                             
    6                                                             
    5                                                             
    4                                                             
    3                                                             
    2                                                             
    1                                                             
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Connected Calls (last 60 seconds)
          # = Connected calls handled by the module

                                                                  
                                                                  
                                                     369963146641 
                                                    8880000440044 
                                                    8880077990066 
  910                                                  **         
  820                                                  #*         
  730                                                 *##         
  640                                                 *##*   **   
  550                                                 ###*   ##   
  460                                                 ####  *##*  
  370                                                *####  *##*  
  280                                                #####* ####  
  190                                                ######*####* 
  100                                               *######*####* 
   10                                               ############# 
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Connected Calls (last 60 minutes)
          * = maximum Connected calls    # = average Connected calls

                                                                              
                                                                              
      9                                                                       
      0                                                                       
      0                                                                       
  970                                                                         
  890 *                                                                       
  810 *                                                                       
  730 *                                                                       
  650 *                                                                       
  570 *                                                                       
  490 *                                                                       
  410 *                                                                       
  330 *                                                                       
  250 *                                                                       
  170 #                                                                       
     0....5....1....1....2....2....3....3....4....4....5....5....6....6....7..
               0    5    0    5    0    5    0    5    0    5    0    5    0  
          Connected Calls (last 72 hours)
          * = maximum Connected calls    # = average Connected calls

The following section describes how to interpret the graphical data:

  • Connected calls for the last 60 seconds—The graph displays the number of connected calls in the last 60 seconds. X-axis represents the time in seconds and Y-axis represents the number of connected calls. # represents the number of connected calls.

    For example, in the following graph, 15 calls were connected at the 2nd second.

    
                             1                  
           1122334455667788990998877665544332211                        
           5050505050505061505050505050505050505                       
      100                   ###                                         
       90                 #######                                       
       80               ###########                                     
       70             ###############                                   
       60           ###################                                 
       50         #######################                               
       40       ###########################                             
       30     ###############################                           
       20    ##################################                         
       10  #####################################                       
         0....5....1....1....2....2....3....3....4....4....5....5....6
                   0    5    0    5    0    5    0    5    0    5    0
    
  • Connected calls for the last 60 minutes—The graph displays the number of connected calls in the last 60 minutes. X-axis represents the time in minutes and Y-axis represents the number of connected calls. The values on the Y-axis vary based on the number of connected calls. * represents the maximum number of connected calls. # represents the average number of connected calls. The maximum number of connected calls over a minute is calculated by taking the average of 3 maximum values of connected calls over the 60 seconds in that minute.

    For example, in the following graph, on the 48th minute, a maximum of 383 calls were connected and average calls were 10.

    
    
                                                         369863146641 
                                                        8880900440044 
                                                        3330922440011 
      910                                                  **         
      820                                                  #*         
      730                                                  ##         
      640                                                 *##*   **   
      550                                                 ###*   ##   
      460                                                 ####  *##*  
      370                                                *####  *##*  
      280                                                #####* ####  
      190                                                ###### ####  
      100                                               *######*####* 
       10                                               ############# 
         0....5....1....1....2....2....3....3....4....4....5....5....6
                   0    5    0    5    0    5    0    5    0    5    0
              Connected Cube Calls (last 60 minutes)
              * = maximum Connected calls    # = average Connected calls
  • Connected calls for the last 72 hours—The graph displays the number of connected calls in the last 72 hours. X-axis represents the time in hours and Y-axis represents the number of connected calls. The values on the Y-axis vary based on the number of connected calls. * represents the maximum number of connected calls. # represents the average number of connected calls. The maximum connected calls over each hour are the same as the maximum connected calls over the minutes in that hour.

    For example, in the following graph, during the first hour, a maximum of 900 calls were connected and average calls were 170.

    
            
          9                                                                       
          0                                                                       
          0                                                                       
      970                                                                         
      890 *                                                                       
      810 *                                                                       
      730 *                                                                       
      650 *                                                                       
      570 *                                                                       
      490 *                                                                       
      410 *                                                                       
      330 *                                                                       
      250 *                                                                       
      170 #                                                                       
         0....5....1....1....2....2....3....3....4....4....5....5....6....6....7..
                   0    5    0    5    0    5    0    5    0    5    0    5    0  
              Connected Cube Calls (last 72 hours)
              * = maximum Connected calls    # = average Connected calls

Use table keyword to display the connected call statistics in tabular format. The output includes the following tables:

  • Connected calls for the last 60 seconds

  • Connected calls for the last 60 minutes

  • Connected calls for the last 72 hours

Examples

Device#show call history stats connected table 

   11:01:44 AM Thursday Aug 29 2019 IST



Connected Calls  (last 60 seconds)
Period     Average       Max
----------------------------
 1-5           0          0
 6-10          0          0
11-15          0          0
16-20          0          0
21-25          0          0
26-30          0          0
31-35          0          0
36-40          0          0
41-45          0          0
46-50          0          0
51-55          0          0
56-60          0          0


Connected Calls  (last 60 minutes)
Period     Average       Max
----------------------------
 1-5           0          0
 6-10          0          0
11-15          0          0
16-20          0          0
21-25          0          0
26-30          0          0
31-35          0          0
36-40          0          0
41-45          0          0
46-50        324        900
51-55        343        900
56-60        292        600

          
Connected Calls  (last 72 hours)
Period     Average       Max
----------------------------
 1-5          35        900
 6-10          0          0
11-15          0          0
16-20          0          0
21-25          0          0
26-30          0          0
31-35          0          0
36-40          0          0
41-45          0          0
46-50          0          0
51-55          0          0
56-60          0          0
61-65          0          0
66-70          0          0
71-72          0          0

Examples


Device#show call history stats cps

   10:26:05 AM Wednesday Sep 25 2019 UTC

                                                                  
                                                                  
                                                                  
                                                                  
                                                                  
   10                                                             
    9                                                             
    8                                                             
    7                                                             
    6                                                             
    5                                                             
    4                                                             
    3                                                             
    2                                                             
    1                                                             
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Call switching rate / CPS (last 60 seconds)
          # = calls handled by the module per second

                                                                  
                                                                  
                                                                  
                                                                  
                                   11                             
   10                                                             
    9                                                             
    8                                                             
    7                                                             
    6                                                             
    5                                                             
    4                                                             
    3                                                             
    2                                                             
    1                              **                             
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Call switching rate / CPS  (last 60 minutes)
          * = maximum calls/s    # = average calls/s

                                                                              
                                                                              
                                                                              
                                                                              
      1                                                                       
   10                                                                         
    9                                                                         
    8                                                                         
    7                                                                         
    6                                                                         
    5                                                                         
    4                                                                         
    3                                                                         
    2                                                                         
    1 *                                                                       
     0....5....1....1....2....2....3....3....4....4....5....5....6....6....7..
               0    5    0    5    0    5    0    5    0    5    0    5    0  
          Call switching rate / CPS (last 72 hours)
          * = maximum calls/s    # = average calls/s

Examples


Device#show call history stats cps detail 

   10:23:27 AM Wednesday Sep 25 2019 UTC

                                                                  
                                                                  
                                                                  
                                                                  
                                                                  
   10                                                             
    9                                                             
    8                                                             
    7                                                             
    6                                                             
    5                                                             
    4                                                             
    3                                                             
    2                                                             
    1                                                             
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Call switching rate / CPS (last 60 seconds)
          # = calls handled by the module per second

                                                                  
                                                                  
                                                                  
                                                                  
                                 11                               
   10                                                             
    9                                                             
    8                                                             
    7                                                             
    6                                                             
    5                                                             
    4                                                             
    3                                                             
    2                                                             
    1                            **                               
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Call switching rate / CPS  (last 60 minutes)
          * = maximum calls/s    # = average calls/s

                                                                              
                                                                              
                                                                              
                                                                              
      1                                                                       
   10                                                                         
    9                                                                         
    8                                                                         
    7                                                                         
    6                                                                         
    5                                                                         
    4                                                                         
    3                                                                         
    2                                                                         
    1 *                                                                       
     0....5....1....1....2....2....3....3....4....4....5....5....6....6....7..
               0    5    0    5    0    5    0    5    0    5    0    5    0  
          Call switching rate / CPS (last 72 hours)
          * = maximum calls/s    # = average calls/s


   10:23:27 AM Wednesday Sep 25 2019 UTC

                                                                  
                                                                  
                                                                  
                                                                  
                                                                  
   10                                                             
    9                                                             
    8                                                             
    7                                                             
    6                                                             
    5                                                             
    4                                                             
    3                                                             
    2                                                             
    1                                                             
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Call-leg switching rate (last 60 seconds)
          # = call legs handled by the module per second

                                                                  
                                                                  
                                                                  
                                                                  
                                 11                               
   10                                                             
    9                                                             
    8                                                             
    7                                                             
    6                                                             
    5                                                             
    4                                                             
    3                                                             
    2                                                             
    1                            **                               
     0....5....1....1....2....2....3....3....4....4....5....5....6
               0    5    0    5    0    5    0    5    0    5    0
          Call-leg switching rate (last 60 minutes)
          * = maximum call-legs/s    # = average call-legs/s

                                                                              
                                                                              
                                                                              
                                                                              
      1                                                                       
   10                                                                         
    9                                                                         
    8                                                                         
    7                                                                         
    6                                                                         
    5                                                                         
    4                                                                         
    3                                                                         
    2                                                                         
    1 *                                                                       
     0....5....1....1....2....2....3....3....4....4....5....5....6....6....7..
               0    5    0    5    0    5    0    5    0    5    0    5    0  
          Call-leg switching rate (last 72 hours)
          * = maximum call-legs/s    # = average call-legs/s

Examples


Device#show call history stats cps table

 10:26:50 AM Wednesday Sep 25 2019 UTC



Call switching rate / CPS (last 60 seconds)
Period     Actual     Average
-----------------------------
 1-5           0          0
 6-10          0          0
11-15          0          0
16-20          0          0
21-25          0          0
26-30          0          0
31-35          0          0
36-40          0          0
41-45          0          0
46-50          0          0
51-55          0          0
56-60          0          0


Call switching rate / CPS (last 60 minutes)
Period     Average       Max
----------------------------
 1-5           0          0
 6-10          0          0
11-15          0          0
16-20          0          0
21-25          0          0
26-30          0          0
31-35          0          1
36-40          0          0
41-45          0          0
46-50          0          0
51-55          0          0
56-60          0          0


Call switching rate / CPS (last 72 hours)
Period     Average       Max
----------------------------
 1-5           0          1
 6-10          0          0
11-15          0          0
16-20          0          0
21-25          0          0
26-30          0          0
31-35          0          0
36-40          0          0
41-45          0          0
46-50          0          0
51-55          0          0
56-60          0          0
61-65          0          0
66-70          0          0
71-72          0          0

show call history video

To display call history information for signaling connection control protocol (SCCP) video calls, use the show call history video command in user EXEC or privileged EXEC mode.

show call history video [ [brief] [id identifier] | compact [duration {less | more} seconds] | last number]

Syntax Description

brief

(Optional) Displays a truncated version of video call history information.

id identifier

(Optional) Displays only the video call history with the specified identifier. Range is a hexadecimal value from 1 to FFFF.

compact

(Optional) Displays a compact version of video call history information.

duration

(Optional) Displays the call history for the specified time duration.

less

Displays the call history for shorter duration calls.

more

Displays the call history for longer duration calls.

seconds

Time, in seconds. The range is from 1 to 2147483647.

last number

(Optional) Displays the last calls connected, where the number of calls that appear is defined by the number argument. The range is from 1 to 100 .

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Cisco IOS Release

Cisco Product

Modification

12.4(4)XC

Cisco Unified CME 4.0

This command was introduced.

12.4(9)T

Cisco Unified CME 4.0

This command was integrated into Cisco IOS Release 12.4(9)T.

12.4(16); 12.4(15)T

Cisco Unified CME 4.0

This command was modified. The Port and BearerChannel display fields were added to the TELE call leg record of the command output.

Examples

The following is sample output from the show call history video command with the compact option:


Router# show call history video compact
      <callID>  A/O FAX T<sec> Codec       type        Peer Address       IP R<ip>:<udp>
Total call-legs: 2
       241      ANS     T17    g729r8      VOIP        P555-0100          192.0.2.0:16926
       242      ORG     T17    g729r8      TELE-VIDEO  P555-0101

The table below describes the significant fields shown in the display.

Table 4. show call history video Field Descriptions

Field

Description

callID

Unique identifier for the call leg.

A/O

Call leg was an answer (ANS) or an originator (ORG).

FAX

Fax number for the call leg.

T<sec>

Duration in seconds.

Codec

Codec used for this call leg.

type

Call type for this call leg.

Peer Address

Called or calling number of the remote peer.

IP R<ip>:<udp>

IP address and port number

Total call-legs

Total number of call legs for this call.

show call history video record

To display information about incoming and outgoing video calls, use the s how call history video record command in privileged EXEC mode.

show call history video record

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(5)XK

This command was introduced on the Cisco MC3810.

12.0(7)T

This command was integrated into Cisco IOS Release 12.0(7)T.

Examples

The following example displays information about two video calls:


Router# show call history video record
CallId = 4
CalledNumber = 221
CallDuration = 39006 seconds
DisconnectText = remote hangup
SVC: call ID = 8598630
Remote NSAP = 47.0091810000000002F26D4901.00107B09C645.C8
Local NSAP = 47.0091810000000002F26D4901.00107B4832E1.C8
vcd = 414, vpi = 0, vci = 158
SerialPort = Serial0
VideoSlot = 1, VideoPort = 0
CallId = 3
CalledNumber = 221
CallDuration = 557 seconds
DisconnectText = local hangup
SVC: call ID = 8598581
Remote NSAP = 47.0091810000000002F26D4901.00107B09C645.C8
Local NSAP = 47.0091810000000002F26D4901.00107B4832E1.C8
vcd = 364, vpi = 0, vci = 108
SerialPort = Serial0
VideoSlot = 1, VideoPort = 0

show call history voice

To display the call history table for voice calls, use the show call history voice command in user EXEC or privileged EXEC mode.

show call history voice [brief [id identifier] | compact [duration {less | more} seconds] | dest-route-string tag | id identifier | last number | redirect {rtpvt | tbct} | stats]

Syntax Description

brief

(Optional) Displays a truncated version of the call history table.

id identifier

(Optional) Displays only the call with the specified identifier. Range is from 1 to FFFF.

compact

(Optional) Displays a compact version of the call history table.

dest-route-string tag

(Optional) Displays only the call with the specified destination route tag value. The range is from 1 to 10000.

duration seconds

(Optional) Displays history information for calls that are longer or shorter than the value of the specified seconds argument. The arguments and keywords are as follows:

  • less --Displays calls shorter than the seconds value.

  • more --Displays calls longer than the seconds value.

  • seconds --Elapsed time, in seconds. Range is from 1 to 2147483647.

last number

(Optional) Displays the last calls connected, where the number of calls that appear is defined by the number argument. Range is from 1 to 100 .

redirect

(Optional) Displays information about calls that were redirected using Release-to-Pivot (RTPvt) or Two B-Channel Transfer (TBCT). The keywords are as follows:

  • rtpvt --Displays information about RTPvt calls.

  • tbct --Displays information about TBCT calls.

stats

(Optional) Displays information about digital signal processing (DSP) voice quality metrics.

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Release

Modification

11.3(1)T

This command was introduced on the Cisco 3600 series.

12.0(3)XG

Support was added for Voice over Frame Relay (VoFR) on the Cisco 2600 series and Cisco 3600 series.

12.0(4)XJ

This command was modified for store-and-forward fax.

12.0(4)T

The brief keyword was added, and the command was implemented on the Cisco 7200 series.

12.0(5)XK

This command was implemented on the Cisco MC3810.

12.0(7)XK

The brief keyword was implemented on the Cisco MC3810.

12.0(7)T

This command was integrated into Cisco IOS Release 12.0(7)T.

12.1(2)T

This command was integrated into Cisco IOS Release 12.1(2)T.

12.1(5)XM

This command was implemented on the Cisco AS5800.

12.1(5)XM2

This command was implemented on the Cisco AS5350 and Cisco AS5400.

12.2(2)XA

The output of this command was modified to indicate whether a specified call has been established using Annex E.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T. Support was not included for the Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850.

12.2(11)T

Support was added for Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850.

12.2(13)T

The ReleaseSource field was added to the Field Description table, and the record keyword was deleted from the command name.

12.3(1)

The redirect keyword was added.

12.4(2)T

The LocalHostname display field was added to the VoIP call leg record.

12.4(11)XW

The stats keyword was added.

12.4(15)T

The Port and BearerChannel display fields were added to the TELE call leg record of the command output.

12.4(16)

The Port and BearerChannel display fields were added to the TELE call leg record of the command output.

12.4(22)T

Command output was updated to show IPv6 information.

15.3(3)M

This command was modified. The dest-route-string keyword was added.

Cisco IOS XE Release 3.10S

This command was integrated into Cisco IOS XE Release 3.10S.

Usage Guidelines

This command displays a call-history table that contains a list of voice calls connected through the router in descending time order. The maximum number of calls contained in the table can be set to a number from 0 to 500 using the dial-control-mib command in global configuration mode. The default maximum number of table entries is 50. Each call record is aged out of the table after a configurable number of minutes has elapsed. The timer value is also specified by the dial-control-mib command. The default timer value is 15 minutes.

You can display subsets of the call history table by using specific keywords. To display the last calls connected through this router, use the last keyword, and define the number of calls to be displayed with the number argument.

To display a truncated version of the call history table, use the brief keyword.

Use the show call active voice redirect command to review records for calls that implemented RTPvt or TBCT.

When a call is active, you can display its statistics by using the show call active voice command.

Use the show call active voice dest-route-string command to display only the active voice calls with call routing configured using specified destination-route-string globally and at the dial-peer level.

Examples

The following is sample output from the show call history voice command:


Router# show call history voice
GENERIC:
SetupTime=104648 ms
Index=1
PeerAddress=55240
PeerSubAddress=
PeerId=2
PeerIfIndex=105
LogicalIfIndex=0
DisconnectCause=10
DisconnectText=normal call clearing.
ConnectTime=104964
DisconectTime=143329
CallDuration=00:06:23
CallOrigin=1
ChargedUnits=0
InfoType=speech
TransmitPackets=37668
TransmitBytes=6157536
ReceivePackets=37717
ReceiveBytes=6158452
VOIP:
ConnectionId[0x4B091A27 0x3EDD0003 0x0 0xFEFD4]
CallID=2
RemoteIPAddress=10.14.82.14
RemoteUDPPort=18202
RoundTripDelay=2 ms
SelectedQoS=best-effort
tx_DtmfRelay=inband-voice
FastConnect=TRUE
SessionProtocol=cisco
SessionTarget=ipv4:10.14.82.14
OnTimeRvPlayout=40
GapFillWithSilence=0 ms
GapFillWithPrediction=0 ms
GapFillWithInterpolation=0 ms
GapFillWithRedundancy=0 ms
HiWaterPlayoutDelay=67 ms
LoWaterPlayoutDelay=67 ms
ReceiveDelay=67 ms
LostPackets=0 ms
EarlyPackets=0 ms
LatePackets=0 ms
VAD = enabled
CoderTypeRate=g729r8
CodecBytes=20
cvVoIPCallHistoryIcpif=0
SignalingType=cas
Modem passthrough signaling method is nse
Buffer Fill Events = 0
Buffer Drain Events = 0
Percent Packet Loss = 0
Consecutive-packets-lost Events = 0
Corrected packet-loss Events = 0
Last Buffer Drain/Fill Event = 373sec
Time between Buffer Drain/Fills = Min 0sec Max 0sec
GENERIC:
SetupTime=104443 ms
Index=2
PeerAddress=50110
PeerSubAddress=
PeerId=100
PeerIfIndex=104
LogicalIfIndex=10
DisconnectCause=10
DisconnectText=normal call clearing.
ConnectTime=104964
DisconectTime=143330
CallDuration=00:06:23
CallOrigin=2
ChargedUnits=0
InfoType=speech
TransmitPackets=37717
TransmitBytes=5706436
ReceivePackets=37668
ReceiveBytes=6609552
TELE:
ConnectionId=[0x4B091A27 0x3EDD0003 0x0 0xFEFD4]
CallID=3
Port=3/0/0 (3)
BearerChannel=3/0/0.1
TxDuration=375300 ms
VoiceTxDuration=375300 ms
FaxTxDuration=0 ms
CoderTypeRate=g711ulaw
NoiseLevel=-75
ACOMLevel=11
SessionTarget=
ImgPages=0

The following example from a Cisco AS5350 router displays a sample of voice call history records showing release source information:


Router# show call history voice
Telephony call-legs: 1
SIP call-legs: 0
H323 call-legs: 1
Total call-legs: 2
GENERIC:
SetupTime=85975291 ms
.
.
.
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=85975335
DisconnectTime=85979339
CallDuration=00:00:40
CallOrigin=1
ReleaseSource=1
.
.
.
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=85975335
DisconnectTime=85979339
CallDuration=00:00:40
CallOrigin=1
ReleaseSource=1
.
.
.
VOIP:
ConnectionId[0x2868AD84 0x375B11D4 0x8012F7A5 0x74DE971E]
CallID=1
.
.
.
GENERIC:
SetupTime=85975290 ms
.
.
.
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=85975336
DisconnectTime=85979340
CallDuration=00:00:40
CallOrigin=2
ReleaseSource=1
.
.
.
TELE:
ConnectionId=[0x2868AD84 0x375B11D4 0x8012F7A5 0x74DE971E]
CallID=2
Port=3/0/0 (2)
BearerChannel=3/0/0.1

The following is sample output from the show call history voice brief command:


Router# show call history voice brief
<ID>: <CallID> <start>hs.<index> +<connect> +<disc> pid:<peer_id> <direction> <addr> 
dur hh:mm:ss tx:<packets>/<bytes> rx:<packets>/<bytes> <disc-cause>(<text>)
IP <ip>:<udp> rtt:<time>ms pl:<play>/<gap>ms lost:<lost>/<early>/<late>
delay:<last>/<min>/<max>ms <codec>
media inactive detected:<y/n> media cntrl rcvd:<y/n> timestamp:<time>
MODEMPASS <method> buf:<fills>/<drains> loss <overall%> <multipkt>/<corrected>
last <buf event time>s dur:<Min>/<Max>s
FR <protocol> [int dlci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>
<codec> (payload size)
ATM <protocol> [int vpi/vci cid] vad:<y/n> dtmf:<y/n> seq:<y/n>
<codec> (payload size)
Telephony <int> (callID) [channel_id] tx:<tot>/<voice>/<fax>ms <codec> noise:<lvl>dBm acom:<lvl>dBm
MODEMRELAY info:<rcvd>/<sent>/<resent> xid:<rcvd>/<sent> total:<rcvd>/<sent>/<drops> disc:<cause code>
speeds(bps): local <rx>/<tx> remote <rx>/<tx>
Proxy <ip>:<audio udp>,<video udp>,<tcp0>,<tcp1>,<tcp2>,<tcp3> endpt: <type>/<manf>
bw: <req>/<act> codec: <audio>/<video>
tx: <audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes>
rx: <audio pkts>/<audio bytes>,<video pkts>/<video bytes>,<t120 pkts>/<t120 bytes>

The following is sample output from the show call history voice redirect command:


Router# show call history voice redirect tbct
index=2, xfr=tbct-notify, status=redirect_success, start_time=*00:12:25.981 UTC Mon Mar 1 1993, ctrl name=T1-2/0,  tag=13
index=3, xfr=tbct-notify, status=redirect_success, start_time=*00:12:25.981 UTC Mon Mar 1 1993, ctrl name=T1-2/0,  tag=13
index=4, xfr=tbct-notify, status=redirect_success, start_time=*00:13:07.091 UTC Mon Mar 1 1993, ctrl name=T1-2/0,  tag=12
index=5, xfr=tbct-notify, status=redirect_success, start_time=*00:13:07.091 UTC Mon Mar 1 1993, ctrl name=T1-2/0,  tag=12
Number of call-legs redirected using tbct with notify:4

The table below describes the significant fields shown in the show call history voice redirect tbct display.

Table 5. show call history voice redirect Field Descriptions

Field

Description

index

Index number of the record in the history file.

xfr

Whether TBCT or TBCT with notify has been invoked.

status

Status of the redirect request.

start_time

Time, in hours, minutes, and seconds when the redirected call began.

ctrl name

Name of the T1 controller where the call originated.

tag

Call tag number that identifies the call.

Number of call-legs redirected using tbct with notify

Total number of call legs that were redirected using TBCT with notify.

show call history watermark connected table

To display the last n high watermark that is achieved by number of connected call rates per second in various periods, use the show call history watermark connected table command. The periods are seconds, minutes, and hours since the last reload. The size of the table is variable and is configurable.

show call history watermark connected table [ [brief] [id identifier] | compact [duration {less | more} seconds] | last number]

This command has no arguments or keywords.

Command Modes


Privileged EXEC (#)

Cisco IOS Release

Modification

15.3(1)T

This command was introduced.

Examples

The following is a sample output in the show call history watermark connected table command:

The output displays a tabular format of call rate per second for the last 1 minute, 1 hour, and all time.


Device#show call history watermark connected table
Device   01:48:05 AM Thursday Mar 14 2019 UTC
===============================================
Connected Calls
------- The WaterMark Table for Second --------
Value : 0, ts : [Thu, 14 Mar 2019 01:48:01 GMT]
Value : 0, ts : [Thu, 14 Mar 2019 01:48:02 GMT]
Value : 0, ts : [Thu, 14 Mar 2019 01:48:03 GMT]
Value : 0, ts : [Thu, 14 Mar 2019 01:48:04 GMT]
Value : 0, ts : [Thu, 14 Mar 2019 01:48:05 GMT]
------- The WaterMark Table for Minute-------
Value : 0, ts : [Wed, 13 Mar 2019 05:33:06 GMT]
Value : 0, ts : [Wed, 13 Mar 2019 05:33:06 GMT]
Value : 0, ts : [Wed, 13 Mar 2019 05:33:06 GMT]
Value : 0, ts : [Wed, 13 Mar 2019 05:33:06 GMT]
Value : 0, ts : [Wed, 13 Mar 2019 05:33:06 GMT]
------- The WaterMark Table for Hour --------
Value : 0, ts : [Wed, 13 Mar 2019 05:16:05 GMT]
Value : 0, ts : [Wed, 13 Mar 2019 05:16:05 GMT]
Value : 0, ts : [Wed, 13 Mar 2019 05:16:05 GMT]
Value : 1, ts : [Wed, 13 Mar 2019 00:12:05 GMT]
Value : 1, ts : [Wed, 13 Mar 2019 05:16:05 GMT]
------- The WaterMark Table for Alltime------
Value : 1, ts : [Sun, 10 Mar 2019 01:39:05 GMT]
Value : 1, ts : [Sun, 10 Mar 2019 23:06:05 GMT]
Value : 1, ts : [Wed, 13 Mar 2019 00:12:05 GMT]
Value : 1, ts : [Wed, 13 Mar 2019 05:16:05 GMT]
Value : 2, ts : [Sun, 10 Mar 2019 23:57:05 GMT]
Device#

Usage Guidelines

This command displays the last n high watermark that is achieved by number of connected call rates per second in various periods. The periods are seconds, minutes, and hours since the last reload.

show call language voice

To display a summary of languages configured and the URLs of the corresponding Tool Command Language (TCL) modules for the languages that are not built-in languages, use the show call language voice command in EXEC mode.

show call language voice [language | summary]

Syntax Description

language

(Optional) Two-character prefix configured with the call language voice command in global configuration mode, either for a prefix for a built-in language or one that you have defined; for example, "en" for English or "ru" for Russian.

summary

(Optional) Summary of all the languages configured and the URLs for the TCL modules other than built-in languages.

Command Modes


EXEC (#)

Command History

Release

Modification

12.2(2)T

This command was introduced.

Usage Guidelines

This command is similar to the show call application voice command. If a language is built in, the URL listed reads "fixed." If you decide to overwrite the built-in language with your own language, the word "fixed" in the URL column changes to the actual URL where your new application lives.

Examples

The following command displays a summary of the configured languages:


Router# show call language voice summary
name       url
sp         fixed
ch         fixed
en         fixed
ru         tftp://dirt/fwarlau/scripts/multilag/ru_translate.tcl

The following command displays information about Russian-language configuration:


Router# show call language voice ru
ru_translate.tcl
ru_translate.tcl~
singapore.cfg
test.tcl
people% more ru_translate.tcl
# Script Locked by: farmerj
# Script Version: 1.1.0.0
# Script Lock Date: Sept 24 2000
# ca_translate.tcl
#------------------------------------------------------------------
# Sept 24, 2000 Farmer Joe
#
# Copyright (c) 2000 by Cisco Systems, Inc.
# All rights reserved.
#------------------------------------------------------------------
#<snip>...
...set prefix ""
#puts "argc"
#foreach arg $argv {
#puts "$arg"
#    translates $arg
#    puts "\t\t**** $prompt RETURNED"
#}

Field descriptions should be self-explanatory.

show call leg

To display event logs and statistics for voice call legs, use the show call leg command in privileged EXEC mode.

show call leg {active | history} [summary | [last number | leg-id leg-id] [event-log | info]]

Syntax Description

active

Statistics or event logs for active call legs.

history

Statistics or event logs for terminated call legs.

summary

(Optional) A summary of each call leg.

last number

(Optional) Selected number of most recent call legs. Not available with active keyword.

leg-id leg-id

(Optional) A specific call leg. Output displays event logs or statistics for that call leg.

event-log

(Optional) Event logs for call legs.

info

(Optional) Statistics for call legs.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.3(8)T

This command was introduced.

Usage Guidelines

If you use the leg-id keyword, only statistics or event logs for that call leg display. To display event logs with this command, you must enable event logging with the call leg event-log command.

Examples

The following is sample output from the show call leg command using different keywords:


Router# show call leg active summary
G<id>  L<id>     Elog A/O FAX T<sec> Codec       type  Peer Address       IP R<ip>:<udp>
G11DC  L A        Y   ANS     T2     None        TELE  P4085550198
Total call-legs: 1
Router# show call leg active event-log
 
Event log for call leg ID: A        Connection ID: 11DC 
buf_size=4K, log_lvl=INFO
<ctx_id>:<timestamp>:<seq_no>:<severity>:<msg_body>
A:1057277701:71:INFO: Call setup indication received, called = 4085550198,  calling = 52927, echo canceller = enable, direct inward dialing
A:1057277701:72:INFO: Dialpeer = 1
A:1057277701:77:INFO: Digit collection
A:1057277701:78:INFO: Call connected using codec None
Total call-legs: 1
Router# show call leg active info
 
Information for call leg ID: A        Connection ID: 11DC 
 GENERIC:
SetupTime=3012940 ms
Index=1
PeerAddress=4085550198
PeerSubAddress=
PeerId=1
PeerIfIndex=329
LogicalIfIndex=253
ConnectTime=301295
CallDuration=00:00:20
CallState=4
CallOrigin=2
ChargedUnits=0
InfoType=2
TransmitPackets=412
TransmitBytes=98880
ReceivePackets=0
ReceiveBytes=0
TELE:
ConnectionId=[0x632D2CAB 0xACEB11D7 0x80050030 0x96F8006E]
IncomingConnectionId=[0x632D2CAB 0xACEB11D7 0x80050030 0x96F8006E]
TxDuration=20685 ms
VoiceTxDuration=0 ms
FaxTxDuration=0 ms
CoderTypeRate=None
NoiseLevel=-120
ACOMLevel=90
OutSignalLevel=-50
InSignalLevel=-41
InfoActivity=0
ERLLevel=38
EchoCancellerMaxReflector=16685
SessionTarget=
ImgPages=0
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=4085550198
OriginalCallingOctet=0x0
OriginalCalledNumber=52927
OriginalCalledOctet=0xE9
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0xFF
TranslatedCallingNumber=4085550198
TranslatedCallingOctet=0x0
TranslatedCalledNumber=52927
TranslatedCalledOctet=0xE9
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwReceivedCalledNumber=52927
GwReceivedCalledOctet3=0xE9
GwReceivedCallingNumber=4085550198
GwReceivedCallingOctet3=0x0
GwReceivedCallingOctet3a=0x81
Total call-legs: 1

For a description of the call leg statistics, see the description for the show call active voice command.


Router# show call leg active leg-id A
 
Call Information - Connection ID: 11DC , Call Leg ID: A
 GENERIC:
SetupTime=3012940 ms
Index=1
PeerAddress=4085550198
PeerSubAddress=
PeerId=1
PeerIfIndex=329
LogicalIfIndex=253
ConnectTime=301295
CallDuration=00:00:40
CallState=4
CallOrigin=2
ChargedUnits=0
InfoType=2
TransmitPackets=824
TransmitBytes=197760
ReceivePackets=0
ReceiveBytes=0
TELE:
ConnectionId=[0x632D2CAB 0xACEB11D7 0x80050030 0x96F8006E]
IncomingConnectionId=[0x632D2CAB 0xACEB11D7 0x80050030 0x96F8006E]
TxDuration=20685 ms
VoiceTxDuration=0 ms
FaxTxDuration=0 ms
CoderTypeRate=None
NoiseLevel=-120
ACOMLevel=90
OutSignalLevel=-50
InSignalLevel=-41
InfoActivity=0
ERLLevel=38
EchoCancellerMaxReflector=16685
SessionTarget=
ImgPages=0
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=4085550198
OriginalCallingOctet=0x0
OriginalCalledNumber=52927
OriginalCalledOctet=0xE9
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0xFF
TranslatedCallingNumber=4085550198
TranslatedCallingOctet=0x0
TranslatedCalledNumber=52927
TranslatedCalledOctet=0xE9
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwReceivedCalledNumber=52927
GwReceivedCalledOctet3=0xE9
GwReceivedCallingNumber=4085550198
GwReceivedCallingOctet3=0x0
GwReceivedCallingOctet3a=0x81
Call Event Log - Connection ID: 11DC , Call Leg ID: A       
buf_size=4K, log_lvl=INFO
<ctx_id>:<timestamp>:<seq_no>:<severity>:<msg_body>
A:1057277701:71:INFO: Call setup indication received, called = 4085550198,  calling = 52927, echo canceller = enable, direct inward dialing
A:1057277701:72:INFO: Dialpeer = 1
A:1057277701:77:INFO: Digit collection
A:1057277701:78:INFO: Call connected using codec None
Call-leg found: 1
Router# show call leg active leg-id A event-log
 
Call Event Log - Connection ID: 11DC , Call Leg ID: A       
buf_size=4K, log_lvl=INFO
<ctx_id>:<timestamp>:<seq_no>:<severity>:<msg_body>
A:1057277701:71:INFO: Call setup indication received, called = 4085550198,  calling = 52927, echo canceller = enable, direct inward dialing
A:1057277701:72:INFO: Dialpeer = 1
A:1057277701:77:INFO: Digit collection
A:1057277701:78:INFO: Call connected using codec None
Call-leg found: 1
Router# show call leg history summary
 
G<id>  L<id>     Elog A/O FAX T<sec> Codec       type  Peer Address       IP R<ip>:<udp> disc-cause
G11DB  L 7        Y   ANS     T24    None        TELE  P4085550198 D10  
G11DC  L A        Y   ANS     T159   None        TELE  P4085550198 D10  
Total call-legs: 2
Router# show call leg history last 1
Call Information - Connection ID: 11DC , Call Leg ID: A
GENERIC:
SetupTime=3012940 ms
Index=4
PeerAddress=4085550198
PeerSubAddress=
PeerId=1
PeerIfIndex=329
LogicalIfIndex=253
DisconnectCause=10  
DisconnectText=normal call clearing (16)
ConnectTime=301295
DisconnectTime=317235
CallDuration=00:02:39
CallOrigin=2
ReleaseSource=1
ChargedUnits=0
InfoType=speech
TransmitPackets=2940
TransmitBytes=705600
ReceivePackets=0
ReceiveBytes=0
TELE:
ConnectionId=[0x632D2CAB 0xACEB11D7 0x80050030 0x96F8006E]
IncomingConnectionId=[0x632D2CAB 0xACEB11D7 0x80050030 0x96F8006E]
TxDuration=20685 ms
VoiceTxDuration=0 ms
FaxTxDuration=0 ms
CoderTypeRate=None
NoiseLevel=-120
ACOMLevel=90
SessionTarget=
ImgPages=0
CallerName=
CallerIDBlocked=False
OriginalCallingNumber=4085550198
OriginalCallingOctet=0x0
OriginalCalledNumber=52927
OriginalCalledOctet=0xE9
OriginalRedirectCalledNumber=
OriginalRedirectCalledOctet=0xFF
TranslatedCallingNumber=4085550198
TranslatedCallingOctet=0x0
TranslatedCalledNumber=52927
TranslatedCalledOctet=0xE9
TranslatedRedirectCalledNumber=
TranslatedRedirectCalledOctet=0xFF
GwReceivedCalledNumber=52927
GwReceivedCalledOctet3=0xE9
GwReceivedCallingNumber=4085550198
GwReceivedCallingOctet3=0x0
GwReceivedCallingOctet3a=0x81
Call Event Log - Connection ID: 11DC , Call Leg ID: A       
buf_size=4K, log_lvl=INFO
<ctx_id>:<timestamp>:<seq_no>:<severity>:<msg_body>
A:1057277701:71:INFO: Call setup indication received, called = 4085550198,  calling = 52927, echo canceller = enable, direct inward dialing
A:1057277701:72:INFO: Dialpeer = 1
A:1057277701:77:INFO: Digit collection
A:1057277701:78:INFO: Call connected using codec None
A:1057277860:150:INFO: Inform application call disconnected (cause = normal call clearing (16))
A:1057277860:154:INFO: Call disconnected (cause = normal call clearing (16))
A:1057277860:155:INFO: Call released
Total call-legs: 1
Total call-legs with event log: 1
Router# show call leg history leg-id A event-log
 
Call Event Log - Connection ID: 11DC , Call Leg ID: A       
buf_size=4K, log_lvl=INFO
<ctx_id>:<timestamp>:<seq_no>:<severity>:<msg_body>
A:1057277701:71:INFO: Call setup indication received, called = 4085550198,  calling = 52927, echo canceller = enable, direct inward dialing
A:1057277701:72:INFO: Dialpeer = 1
A:1057277701:77:INFO: Digit collection
A:1057277701:78:INFO: Call connected using codec None
A:1057277860:150:INFO: Inform application call disconnected (cause = normal call clearing (16))
A:1057277860:154:INFO: Call disconnected (cause = normal call clearing (16))
A:1057277860:155:INFO: Call released
Call-leg matched ID found: 1
Call-legs matched ID with event log: 1

Field descriptions should be self-explanatory.

show call media forking

To display currently active media forking sessions, use the show call media forking command in user EXEC or privileged EXEC mode.

show call media forking

Syntax Description

This command has no arguments or keywords.

Command Modes


User EXEC (>)
Privileged EXEC (#)

Command History

Release

Modification

15.2(2)T

This command was introduced.

Usage Guidelines

Use this command to verify that media forking was successful for relevant anchor legs.

Examples

The following example is a sample output from the show call media forking command..


Router# show call media forking
Warning: Output may be truncated if sessions are added/removed concurrently!
Session Call n/f Destination (port address)
7 6 far 1234 1.5.35.254
8 6 near 5678 1.5.35.254

The table below describes the fields that are displayed in the output.

Field

Description

Session

Session Identifier.

Call

Call Leg identifier in hexadecimal. It must match the Call ID from the show call leg active command.

n/f

Direction (Near End or Far End) of the voice stream that was forked.

Destination (port address)

Destination for the forked packets. It consists of the folllowing:

  • RTP Port

  • IP Address

show callmon

To display call monitor information, use the show callmon command in user EXEC or privileged EXEC mode.

show callmon {call | gcid | subscription | trace {all | event {all | call | connection} | exec | server | subscription | trigger}}

Syntax Description

call

Displays the active call monitor calls.

gcid

Displays the active global call ID information.

subscription

Displays the subscription information.

trace

Displays the trace information.

all

Displays all types of traces based on time.

event

Displays the event trace information.

  • all --Displays all event traces.

  • call --Displays event traces related to a call.

  • connection --Displays the event traces related to a connection.

exec

Displays all critical execution traces.

server

Displays all session server up or down traces.

subscription

Displays all subscription traces.

trigger

Displays the entire trigger structure by index.

Command Modes


User EXEC (>)
Privileged EXEC (#))

Command History

Release

Modification

12.4(22)T

This command was introduced.

Examples

The following sample output from the show callmon call command shows active call monitor calls:


Router# show callmon call
 line dn     sub_id   number of call instance
6401,     1
      callID 2038(19D7),  *cg = 6401, cd = 6601
6601,     1
      callID 2039(19D7),  cg = 6401, *cd = 6601

The table below describes the significant fields shown in the display.

Table 6. show callmon call Field Descriptions

Field

Description

dn

Directory number.

number of call

Number of call instances.

instance

Contents of the call instance.

The following sample output from the show callmon gcid command shows the active global call ID information:


Router# show callmon gcid
 GCID                              callIDs(active_entry_id)
AE48ECBC-D89311DB-87FC996E-115FF692
 isConfGcid:FALSE        gcid_conf:00000000-00000000-00000000-00000000
, 2038(19D7), 2039(19D7)

The table below describes the significant fields shown in the display.

Table 7. show callmon gcid Field Descriptions

Field

Description

GCID

Global call ID.

CallIDs

Active call IDs.

show call prompt-mem-usage

To display the amount of memory used by prompts, use the show call prompt-mem-usage command in privileged EXEC mode.

show call prompt-mem-usage [detail]

Syntax Description

detail

(Optional) Displays details about memory usage and names of tones used.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.2(15)T

This command was introduced.

12.3(7)T

The detail keyword was added.

Usage Guidelines

Use this command to display the number of prompts loaded into the gateway, the amount of memory used by the prompts, the number of prompts currently being played, and the status of prompt loads.

For calls transferred by a Cisco CallManager Express (Cisco CME) system, the ringback tone generation for commit-at-alerting uses an interactive voice response (IVR) prompt playback mechanism. Ringback tone is played to the transferred party by the Cisco CME system associated with the transferring party.

The system automatically generates tone prompts as needed on the basis of the network-locale setting made in the Cisco CME system.

Examples

The following sample output shows details about the memory usage of the prompts that are used.


Router# show call prompt-mem-usage
Prompt memory usage:
             config’d      wait    active      free     mc total    ms total
    file(s)      0200      0010      0001     00189        00011      00002
    memory   02097152  00081259  00055536  01960357     00136795
 Prompt load counts: (counters reset 0)
    success 11(1st try) 0(2nd try), failure 0
 Other mem block usage:
            mcDynamic   mcReader
    gauge       00001      00001
Number of prompts playing: 1 
Number of start delays   : 0
MCs in the ivr MC sharing table
===============================
Media Content: NoPrompt (0x83C64554)
  URL: 
  cid=0, status=MC_READY size=24184 coding=g711ulaw refCount=0
Media Content: tone://GB_g729_tone_ringback (0x83266EC8)
  URL: tone://GB_g729_tone_ringback

The table below describes the significant fields shown in the display.

Table 8. show call prompt-mem-usage Field Descriptions

Field

Description

file(s)

Number of prompts in different queues.

file(s) - config’d

Maximum number of configured prompts that can be simultaneously available in memory. In the sample output, the value of 200 in this field means that loading the 201st prompt results in the oldest prompts being removed.

file(s) -wait

Number of prompts in the wait queue that are not being used in any call and are ready to be deleted when there is no space for a new prompt. This field lists older prompts that can be deleted.

file(s) - active

Number of prompts that are being used in active calls. These prompts cannot be deleted.

file(s) - free

Number of prompts that can be loaded without deleting any prompt from the wait queue. This is the number of configured prompts (listed under config’d) minus the total number of prompts in the wait and active states.

file(s) - mc total

Total number of prompts in the wait and active states.

ms total

Number of media streams that are currently active. One media stream is used for playing INBOX prompts. A prompt is considered an INBOX prompt if its URL is either flash:, http:, ram:, or tftp:.

memory

Displays the memory used by prompts, in bytes.

memory - config’d

Maximum amount of memory configured to be available for prompts.

memory - wait

Total amount of memory used by prompts in the wait list.

memory - active

Total amount of memory used by prompts in the active list.

memory - free

Amount of available memory. This is the amount of configured prompts (listed under config’d) memory minus the total amount of memory used by the prompts in the wait and active lists.

memory - mc total

Total amount of memory used by prompts in the wait and active lists.

Prompt load counts

Number of successful attempts to load a prompt on the first try and on the second try, and the number of attempts to load a prompt that failed.

mcDynamic

Number of dynamic element queues that are active. A dynamic element queue is a list of prompts that are played together.

mcReader

Number of mcReaders that are active. An mcReader is used for playing one mcDynamic queue of prompts. An mcReader is used only if the mcDynamic contains prompts that are associated with one of the following types of URL: flash:, http:, ram:, or tftp:.

Number of prompts playing

Number of prompts that are currently playing.

Number of start delays

Number of times that prompts failed to start and have subsequently restarted.

MCs in the ivr MC sharing table

The fields below this line of text refer to each media content (prompt) currently cached in memory. In the sample output, the only cached prompt is the built-in default prompt named "NoPrompt."

Media Content

Name of the prompt, which is derived from the audio file URL (the characters after the last "/" in the URL). The address in parentheses is the memory location of the prompt.

URL

Location of the file for the prompt that is playing. In the case of the default prompt, NoPrompt, no URL is given.

cid

Call identification number of the call that initiated the loading of the prompt.

status

Status of the media content. The following values are possible:

  • MC_NOT_READY--Initial status for media content. When the media content is successfully loaded, the status will change to MC_READY.

  • MC_READY--Media content is loaded into memory and ready for use.

  • MC_LOAD_FAIL--Media content failed to load.

size

Size of the media content, in bytes.

coding

Type of encoding used by the media content.

refCount=0

Number of calls to which this media content is currently being streamed.

show call resource voice stats

To display resource statistics for an H.323 gateway, use the show call resource voice stats command in privileged EXEC mode.

show call resource voice stats [ds0 | dsp]

Syntax Description

ds0

(Optional) Specifies the voice digital signal level zero (DS0) resource statistics information.

dsp

(Optional) Specifies the voice digital signal processor (DSP) resource statistics information.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(5)T

This command was introduced.

12.1(5)XM2

This command was integrated into Cisco IOS Release 12.1(5)XM2

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB1

This command was integrated into Cisco IOS Release into 12.2(2)XB1.

12.2(8)T

This command was modified. Support for the Cisco AS5300,Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 series routers is not included in this release.

12.4(22)T

This command was modified. The ds0 and dsp keywords were added.

Usage Guidelines

The show call resource voice stats command displays the H.323 resources that are monitored when the resource threshold command is used to configure resource threshold reporting.

Examples

The following is sample output from the show call resource voice stats command, which shows the resource statistics for an H.323 gateway:


Router# show call resource voice stats
Resource Monitor -  Dial-up Resource Statistics Information:
DSP Statistics:
Utilization: 0 percent
Total channels: 48
Inuse channels: 0
Disabled channels 0:
Pending channels: 0
Free channels: 48
DS0 Statistics:
Total channels: 0
Addressable channels: 0
Inuse channels: 0
Disabled channels: 0
Free channels: 0

The table below describes significant fields shown in this output.

Table 9. show call resource voice stats Field Descriptions

Statistic

Definition

Total channels

Number of channels physically configured for the resource.

Inuse channels

Number of addressable channels that are in use. This value includes all channels that either have active calls or have been reserved for testing.

Disabled channels

Number of addressable channels that are physically down or that have been disabled administratively with the shutdown or busyout command.

Pending channels

Number of addressable channels that are pending in loadware download.

Free channels

Number of addressable channels that are free.

Addressable channels

Number of channels that can be used for a specific type of dialup service, such as H.323, which includes all the DS0 resources that have been associated with a voice plain old telephone service (POTS) dial plan profile.

show call resource voice threshold

To display the threshold configuration settings and status for an H.323 gateway, use the show call resource voice threshold command in privileged EXEC mode.

show call resource voice threshold [ds0 | dsp]

Syntax Description

ds0

(Optional) Specifies the voice digital signal level zero (DS0) resource statistics information.

dsp

(Optional) Specifies the voice digital signal processor (DSP) resource statistics information.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(5)T

This command was introduced.

12.1(5)XM2

This command was integrated into Cisco IOS Release 12.1(5)XM2

12.2(2)XB1

This command was integrated into Cisco IOS Release into 12.2(2)XB1.

12.4(22)T

This command was modified. The ds0 and dsp keywords were added.

Usage Guidelines

The show call resource voice threshold command displays the H.323 resource thresholds that are configured with the resource threshold command.

Examples

The following is sample output from the show call resource voice threshold command, which shows the resource threshold settings and status for an H.323 gateway:


Router# show call resource voice threshold
Resource Monitor -  Dial-up Resource Threshold Information:
DS0 Threshold:
Client Type: h323
High Water Mark: 70
Low Water Mark: 60
Threshold State: init
DSP Threshold:
Client Type: h323
High Water Mark: 70
Low Water Mark: 60
Threshold State: low_threshold_hit

The table below describes the significant fields shown in the display.

Table 10. show call resource voice threshold Field Descriptions

Field

Description

High Water Mark

Resource-utilization level that triggers a message indicating that H.323 resource use is high. The range is 1 to 100. A value of 100 indicates that the resource is unavailable.The default is 90.

Low Water Mark

Resource-utilization level that triggers a message indicating that H.323 resource use has dropped below the high-usage level. The range is 1 to 100. The default is 90.

show call rsvp-sync conf

To display the configuration settings for Resource Reservation Protocol (RSVP) synchronization, use the show call rsvp -sync conf command in privileged EXEC mode.

show call rsvp-sync conf

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.1(3)XI1

This command was introduced on the Cisco 2600 series, Cisco 3600 series, Cisco 7200, Cisco MC3810, Cisco AS5300, and Cisco AS5800.

12.1(5)T

This command was integrated into Cisco IOS Release 12.1(5)T.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(8)T

Support for the Cisco AS5300,Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 is not included in this release.

12.2(11)T

This command is supported on the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 in this release.

Examples

The following example shows sample output from this command:


Router# show call rsvp-sync conf
VoIP QoS: RSVP/Voice Signaling Synchronization config:
Overture Synchronization is ON
Reservation Timer is set to 10 seconds

The table below describes significant fields shown in this output.

Table 11. show call rsvp-sync conf Field Descriptions

Field

Description

Overture Synchronization is ON

Indicates whether RSVP synchronization is enabled.

Reservation Timer is set to xx seconds

Number of seconds for which the RSVP reservation timer is configured.

show call rsvp-sync stats

To display statistics for calls that attempted Resource Reservation Protocol (RSVP) reservation, use the show call rsvp -sync stats command in privileged EXEC mode.

show call rsvp-sync stats

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.1(3)XI1

This command was introduced.

12.1(5)T

This command was integrated into Cisco IOS Release 12.1(5)T.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T.

Examples

The following example shows sample output from this command:


Router# show call rsvp-sync stats
VoIP QoS:Statistics Information:
Number of calls for which QoS was initiated   : 18478
Number of calls for which QoS was torn down   : 18478
Number of calls for which Reservation Success was notified : 0
Total Number of PATH Errors encountered : 0
Total Number of RESV Errors encountered : 0
Total Number of Reservation Timeouts encountered : 0

The table below describes significant fields shown in this output.

Table 12. show call rsvp-sync stats Field Descriptions

Field

Description

Number of calls for which QoS was initiated

Number of calls for which RSVP setup was attempted.

Number of calls for which QoS was torn down

Number of calls for which an established RSVP reservation was released.

Number of calls for which Reservation Success was notified

Number of calls for which an RSVP reservation was successfully established.

Total Number of PATH Errors encountered

Number of path errors that occurred.

Total Number of RESV Errors encountered

Number of reservation errors that occurred.

Total Number of Reservation Timeouts encountered

Number of calls in which the reservation setup was not complete before the reservation timer expired.

show call spike status

To display the configured call spike threshold and statistics for incoming calls, use the show call spike status command in privileged EXEC mode.

show call spike status [dial-peer tag]

Syntax Description

dial-peer

(Optional) Displays configuration information for a dial peer.

tag

(Optional) Specifies the dial peer identifying number. Range is from 1 to 2147483647.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.2(2)XA

This command was introduced.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T. This command was not supported on the Cisco AS5300, Cisco AS5350, and Cisco AS5400 in this release.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(4)XM

This command was implemented on the Cisco 1750 and Cisco 1751. This command was not supported on any other platforms in this release.

12.2(8)T

This command was implemented on the Cisco 7200 series. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 was not included in this release.

12.2(11)T

Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 was added in this release.

15.1(3)T

This command was modified. The output fields of the command were modified to include the output at the dial peer level.

Examples

The following is sample output from this command:


Router# show call spike status
 Call Spiking:Configured
 Call spiking :NOT TRIGGERED
 total call count in sliding window ::20

The table below describes the significant fields shown in the display.

Table 13. show call spike status Field Descriptions

Field

Description

Call Spiking

Current enabled state of call spiking.

Call Spiking

Details if the call spiking limit has been triggered.

total call count in sliding window

Number of calls during the spiking interval.


Router# show call spike status dial-peer 400
TAG        CONFIG    SPIKED TOTAL REJECTED CALLS    REJECTED CALLS
400        YES       NO        4                       0             

The table below describes the significant fields shown in the display.

Table 14. show call spike status (dial peer) Field Descriptions

Field

Description

TAG

Dial peer tag.

CONFIG

Displays if the call spike command has been configured.

SPIKED

Details if the call spiking limit has been triggered.

TOTAL REJECTED CALLS

Displays the number of calls rejected due to a call spike in the dial peer.

REJECTED CALLS

Displays the number of calls rejected when the call spike was triggered until the call spike control was released.

show call threshold

To display enabled triggers, current values for configured triggers, and the number of application programming interface (API) calls that were made to global and interface resources, use the show call threshold command in privileged EXEC mode.

show call threshold {config | status [unavailable] | stats}

Syntax Description

config

Displays the current threshold configuration.

status

Displays the status of all configured triggers and whether or not the CPU is available.

unavailable

(Optional) Displays the status for all unavailable resources.

stats

Displays statistics for API calls; that is, the resource-based measurement.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.2(2)XA

This command was introduced.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T. This command is not supported on the Cisco AS5300, Cisco AS5350, and Cisco AS5400 platforms in this release.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(4)XM

This command was implemented on the Cisco 1750 and Cisco 1751. This command is not supported on any other platforms in this release.

12.2(8)T

This command was implemented on the Cisco 7200 series. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.

12.2(11)T

This command was implemented on the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850.

15.2(2)T

This command was modified. The output was modified to display the configured bandwidth threshold, bandwidth availability, and call admission control statistics.

Examples

The following is sample output from the show call threshold config command:


Router# show call threshold config

Some resource polling interval:
  CPU_AVG interval: 60
  Memory interval:  5
IF              Type            Value   Low     High    Enable
-----           ----            -----   ----    ----    ------
Serial3/1:23    int-calls       0       107     107     N/A
N/A             cpu-avg         0        70      90     busy&treat

The following is sample output from the show call threshold status command:


Router# show call threshold status

Status  IF              Type            Value   Low     High    Enable
------  ---             ------          ----    ----    ----    -----
Avail   N/A             total-calls     0       5       5000    busyout
Avail   N/A             cpu-avg         0       5       65      busyout

The following is sample output from the show call threshold status unavailable command:


Router# show call threshold status unavailable

Unavailable configured resources at the current time:
IF              Type            Value   Low     High    Enable
----            -----           -----   ----    ----    -----

The following is sample output from the show call threshold stats command:


Router# show call threshold stats

Total resource check: 0
 successful: 0
 failed:   0

The table below describes significant fields shown in this output.

Table 15. show call threshold Field Descriptions

Field

Description

CPU_AVG interval

Interval of configured trigger CPU_AVG.

Memory interval

Interval of configured trigger Memory.

IF

Interface type and number.

Type

Type of resource.

Value

Value of a call that is to be matched against low and high thresholds.

Low

Low threshold.

High

High threshold.

Enable

Shows if busyout and the call treatment command are enabled.

show call treatment

To display the call-treatment configuration and statistics for handling the calls on the basis of resource availability, use the show call treatment command in privileged EXEC mode.

show call treatment {config | stats}

Syntax Description

config

Displays the call treatment configuration.

stats

Displays statistics for handling the calls on the basis of resource availability.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.2(2)XA

This command was introduced.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T. This command was not supported on the Cisco AS5300, Cisco AS5350, and Cisco AS5400 in this release.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(4)XM

This command was implemented on the Cisco 1750 and Cisco 1751. This command was not supported on any other platforms in this release.

12.2(8)T

This command was implemented on the Cisco 7200 series. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.

12.2(11)T

This command is supported on the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 in this release.

Examples

The following is sample output from this command:


Router# show call treatment config

Call Treatment Config
---------------------
Call treatment is OFF.
Call treatment action is: Reject
Call treatment disconnect cause is: no-resource
Call treatment ISDN reject cause-code is: 41

The table below describes significant fields shown in this output.

Table 16. show call treatment config Field Descriptions

Field

Description

Call treatment is:

State of call treatment, either ON or OFF.

Call treatment action is:

Action trigger assigned for call treatment.

Call treatment disconnect cause is:

Reason for disconnect.

Call treatment ISDN reject cause-code is:

Reject code number assigned.

The following is sample output from the show call treatment command:


Router# show call treatment stats
Call Treatment Statistics
-------------------------
Total Calls by call treatment: 0
Calls accepted by call treatment: 0
Calls rejected by call treatment: 0
Reason          Num. of calls rejected
------          ----------------------
cpu-5sec:       0
cpu-avg:        0
total-mem:      0
io-mem:         0
proc-mem:       0
total-calls:    0

The table below describes significant fields shown in this output.

Table 17. show call treatment stats Field Descriptions

Field

Description

Total Calls by call treatment:

Number of calls received and treated.

Calls accepted by call treatment:

Calls that passed treatment parameters.

Calls rejected by call treatment:

Calls that failed treatment parameters.

cpu-5sec

Number of calls rejected for failing the cpu-5sec parameter.

cpu-avg

Number of calls rejected for failing the cpu-avg parameter.

total-mem

Number of calls rejected for failing the total-mem parameter.

io-mem

Number of calls rejected for failing the io-mem parameter.

proc-mem

Number of calls rejected for failing the proc-mem parameter.

total-calls

Number of calls rejected for failing the total-calls parameter.

show call-router routes

To display the routes cached in the current border element (BE), use the show call-router routes in EXEC mode.

show call-router routes [static | dynamic | all]

Syntax Description

static

Descriptors provisioned on the border element.

dynamic

Dynamically learned descriptors.

all

Both static and dynamic descriptors.

Command Default

All

Command Modes


EXEC (#)

Command History

Release

Modification

12.2(2)XA

This command was introduced.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T.

Examples

The following example is sample output from this command.


Router# show call-router routes
Static Routes:
==============
  DescriptorID= 6561676C65000000000000000000000A
  lastChanged = 19930301063311
   IP addr         :port       Prefix
   172.18.195.64   :2099       5553122
Dynamic Routes:
===============
  DescriptorID= 506174726F6E6F757300000000000002
  lastChanged = 19930228190012
   IP addr         :port       Prefix
   172.18.195.65   :2099       310
  DescriptorID= 506174726F6E6F757300000000000003
  lastChanged = 19930228190012
   IP addr         :port       Prefix
   172.18.195.65   :2099       555301
  DescriptorID= 506174726F6E6F757300000000000004
  lastChanged = 19930228190012
   IP addr         :port       Prefix
   172.18.195.65   :2099       555302
DescriptorID= 506174726F6E6F757300000000000005
  lastChanged = 19930228190012
   IP addr         :port       Prefix
   172.18.195.65   :2099       818
  DescriptorID= 506174726F6E6F757300000000000001
  lastChanged = 19930228190012
   IP addr         :port       Prefix
   172.18.195.65   :2099       1005

Field descriptions should be self-explanatory.

show call-router status

To display the Annex G border element status, use the show call -router status command in user EXEC mode.

show call-router status [neighbors]

Syntax Description

neighbors

(Optional) Displays the neighbor border element status.

Command Modes


User EXEC (#)

Command History

Release

Modification

12.2(2)XA

This command was introduced.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T and modified to add the neighbors keyword.

Examples

The following example displays the Annex G border element status. Note that the example shows the status for two neighbors.:


Router# show call-router status neighbors
ANNEX-G CALL ROUTER STATUS:
  ===========================
    Border Element ID Tag   : Celine
    Domain Name             : Celine-Domain
    Border Element State    : UP
    Border Element Local IP : 172.18.193.31:2099
    Advertise Policy        : STATIC descriptors
    Hopcount Value          : 7
    Descriptor TTL          : 3180
    Access Policy           : Neighbors only
    Current Active Calls    : 0
    Current Calls in Cache  : 0
    Cumulative Active Calls : 0
    Usage Ind Messages Sent : 0
    Usage Ind Cfm Rcvd      : 0
    IRRs Received           : 0
    DRQs Received           : 0
    Usage Ind Send Retrys   : 0
  NEIGHBOR INFORMATION:
  =====================
    Local Neighbor ID : (none)
    Remote Element ID : (unknown)
    Remote Domain ID  : (unknown)
    IP Addr           : 1.2.3.4:2099
    Status            : DOWN
    Caching           : OFF
    Query Interval    : 30 MIN (querying disabled)
    Usage Indications :
      Current Active Calls : 0
      Retry Period         : 600 SEC
      Retry Window         : 3600 MIN
    Service Relationship Status: ACTIVE
      Inbound Service Relationship  : DOWN
        Service ID     : (none)
        TTL            : 1200 SEC
      Outbound Service Relationship : DOWN
        Service ID     : (none)
        TTL            : (none)
        Retry interval : 120 SEC (0 until next attempt)

The table below describes significant fields shown in this output.

Table 18. show call-router status Field Descriptions

Field

Description

Border Element ID Tag

Identifier for the border element.

Border Element State

Indicates if the border element is running.

Border Element Local IP

Local IP address of the border element.

Advertise Policy

Type of descriptors that the border element advertises to its neighbors. Default is static . Other values are dynamic and all .

Hopcount Value

Maximum number of border element hops through which an address resolution request can be forwarded. Default is 7.

Descriptor TTL

Time-to-live value, or the amount of time, in seconds, for which a route from a neighbor is considered valid. Range is from 1 to 2147483647. Default is 1800 (30 minutes).

Access Policy

Requires that a neighbor be explicitly configured for requests to be accepted.

Local Neighbor ID

Domain name reported in service relationships.

Service Relationship Status

Service relationship between two border elements is active.

Inbound Service Relationship

Inbound time-to-Live (TTL) value in number of seconds. Range is from 1 to 4294967295.

Outbound Service Relationship

Specifies the amount of time, in seconds, to establish the outbound relationship. Range is from 1 to 65535.

Retry interval

Retry value between delivery attempts, in number of seconds. Range is from 1 to 3600.

show ccm-manager

To display a list of Cisco CallManager servers and their current status and availability, use the show ccm -manager command in privileged EXEC mode.

show ccm-manager [backhaul | config-download | fallback-mgcp | hosts | music-on-hold | redundancy | download-tones [c1 | c2]]

Syntax Description

backhaul

(Optional) Displays information about the backhaul link.

config-download

(Optional) Displays information about the status of Media Gateway Control Protocol (MGCP) and Skinny Client Control Protocol (SCCP) configuration download.

fallback-mgcp

(Optional) Displays the status of the MGCP gateway fallback feature.

hosts

(Optional) Displays a list of each configured Cisco CallManager server in the network, together with its operational status and host IP address.

music-on-hold

(Optional) Displays information about all the multicast music-on-hold (MOH) sessions in the gateway at any given point in time.

redundancy

(Optional) Displays failover mode and status information for hosts, including the redundant link port, failover interval, keepalive interval, MGCP traffic time, switchover time, and switchback mode.

download-tones c1 | c2

(Optional) Displays custom tones downloaded to the gateway. The custom tone value of c1 or c2 specifies which tone information to display.

Command Default

If none of the optional keywords is specified, information related to all keywords is displayed.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.1(3)T

This command was introduced on the Cisco CallManager Version 3.0 and Cisco VG200.

12.2(2)XA

This command was implemented on the Cisco 2600 series and Cisco 3600 series.

12.2(2)XN

This command was modified to provide enhanced MGCP voice gateway interoperability to Cisco CallManager Version 3.1 for the Cisco 2600 series, Cisco 3600 series, and Cisco VG200.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11) and the Cisco CallManager Version 3.2. It was implemented on the Cisco IAD2420 series.

12.2(15)ZJ

The download-tones [ c1 | c2 ] keywords were added for the following platforms: Cisco 2610XM, Cisco 2611XM, Cisco 2620XM, Cisco 2621XM, Cisco 2650XM, Cisco 2651XM, Cisco 2691, Cisco 3640A, Cisco 3660, Cisco 3725, and Cisco 3745.

12.3(4)T

The keywords were integrated into Cisco IOS Release 12.3(4)T.

12.3(14)T

New output was added relating to SCCP autoconfiguration.

12.4(15)XY

The display output was modified to include the number of TFTP download failures allowed.

Usage Guidelines

Use the show ccm-manager config-download command to determine the status of Cisco Unified Communications Manager servers and the automatic download information and statistics.

Examples

The following sample output shows the configured amplitudes, frequencies, and cadences of custom tone 1, Hong Kong:


Router# show ccm-manager download-tones c1
!
Custom Tone 1 : Hong Kong
Pulse dial:normal, Percent make:35%, DTMF low Amp.= 65424, high Amp.= 65446, Pcm:u-Law
                                      FXS  FXO  E&M  FXS  FXO  E&M
Dual Tone DR NF FOF FOS AOF AOF AOF AOS AOS AOS ONTF OFTF ONTS OFTS ONTT OFTT ONT4 OFT4
(optional) FOF2 FOS2 FOF3 FOS3 FOF4 FOS4 FOT FO4 AOT AO4 RCT1 RCT2 RCT3 RCT4
BUSY 0  2 480 620 -120 -120 -120 -120 -120 -120 500 500 0 0 0 0 0 0
RING_BACK           0  2   440   520 -120 -120 -120 -120 -120 -120   400   200   400  3000 
CONGESTION          0  2   480   620 -200 -200 -200 -240 -240 -240   250   250     0     0 
NUMBER_UNOBTAINABLE 0  2   480   620 -120 -120 -120 -120 -120 -120 65535     0     0     0 
DIAL_TONE           0  2   350   440 -150 -150 -150 -150 -150 -150 65535     0     0     0 
DIAL_TONE2          0  2   350   440 -150 -150 -150 -150 -150 -150 65535     0     0     0 
OUT_OF_SERVICE      0  1   950     0 -150 -150 -150    0    0    0   330   330     0     0 
ADDR_ACK            0  1   600     0 -240 -240 -240    0    0    0   125   125   125 65535 
DISCONNECT          0  1   600     0 -150 -150 -150    0    0    0   330   330   330 65535 
OFF_HOOK_NOTICE     0  2  1400  2040 -240 -240 -240 -240 -240 -240   100   100     0     0 
OFF_HOOK_ALERT      0  2  1400  2040 -240 -240 -240 -240 -240 -240   100   100     0     0 
WAITING             0  0     0     0    0    0    0    0    0    0     0     0     0     0 
CONFIRM             0  0     0     0    0    0    0    0    0    0     0     0     0     0 
CNFWRN_J            0  1   950     0 -170 -170 -190    0    0    0   100   100   100 65535 
CNFWRN_D            0  1   600     0 -170 -170 -190    0    0    0   100   100   100 65535 
STUTT_DIALTONE      0  2   350   440 -150 -150 -150 -150 -150 -150   100   100   100   100   100   100 65535     0
PERM_SIG_TONE       0  1   480     0 -170 -170 -170    0    0    0 65535     0     0     0
WAITING1            0  0     0     0    0    0    0    0    0    0     0     0     0     0 
WAITING2            0  0     0     0    0    0    0    0    0    0     0     0     0     0 
WAITING3            0  0     0     0    0    0    0    0    0    0     0     0     0     0 
WAITING4            0  0     0     0    0    0    0    0    0    0     0     0     0     0 
MSGWAIT_IND         0  0     0     0    0    0    0    0    0    0     0     0     0     0 
OFF_HOOK_WARN       0  0     0     0    0    0    0    0    0    0     0     0     0     0 
Sequence Tone       DR NF F1C1  F2C1   AOF   AOS  C1ONT C1OFT C2ONT C2OFT C3ONT C3OFT C4ONT C4OFT  F1C2  F2C2  F1C3  F2C3  F1C4  F2C4
INTERCEPT           0  0     0     0     0     0      0     0     0     0     0     0 
TONE_ON_HOLD        0  0     0     0     0     0      0     0     0     0     0     0 
NO_CIRCUIT          0  0     0     0     0     0      0     0     0     0     0     0 
Legend:
DR: direction NF: number of frequency FO<F,S,T,4>: frequency of<1st,2nd,3rd,4th>  AO<F,S,T,4>: amplitude of<1st,2nd,3rd,4th>
FOF<1-4>: frequency of 1st, cadence<1-4> FOS<1-4>: frequency of 2nd, cadence<1-4>
RCT<1-4>: repeat count for cadence<l-4>  F(1-4>C<1-4> : frequency<1-4> of cadence<1-4>
C<1-4>ONT: cadence<1-4> on time C<1-4>OFT: cadence<1-4> off time

The three tables below and give descriptions of significant fields once the tones are automatically downloaded to the gateway.

Table 19. show ccm-manager download-tones Significant Output Fields

Field

Description

Percent make

Pulse ratio in percentage of make.

DTMF low Amp.

Low frequency level.

high Amp.

High frequency level.

Pcm

Pulse Code Modulation (mu-law or a-law).

Table 20. show ccm-manager download-tones Output Fields for Dual Tones

Field of Dual Tone

Description

DR

Direction to PSTN (0) or Packet Network (1).

NF

Number of Frequency (from 1 to 4).

FOF

Frequency of First component (in Hz).

FXS AOF

Amplitude of First component (from 1 to 65535 = +3 dBm0) for the foreign exchange station (FXS).

FXO AOF

Amplitude of First component (from 1 to 65535 = +3 dBm0) for the foreign exchange office (FXO).

E&M AOF

Amplitude of First component (from 1 to 65535 = +3 dBm0) for the recEive and transMit (E&M).

FXS AOS

Amplitude of Second component (from 1 to 65535 = +3 dBm0) for the FXS.

FXO AOS

Amplitude of Second component (from 1 to 65535 = +3 dBm0) for the FXO.

E&M AOS

Amplitude of Second component (from 1 to 65535 = +3 dBm0) for the E&M.

ONTF

On time; time the tone is generated (milliseconds) for the first frequency.

OFTF

Off time; silence time (milliseconds) for the first frequency.

ONTS

On time; time the tone is generated (milliseconds) for the second frequency.

OFTS

Off time; silence time (milliseconds) for the second frequency.

ONTT

On time; time the tone is generated (milliseconds) for the third frequency.

OFTT

Off time; silence time (milliseconds) for the third frequency.

ONT4

On time; time the tone is generated (milliseconds) for the fourth frequency.

OFT4

Off time; silence time (milliseconds) for the fourth frequency.

FOF2

Frequency of First component for the second cadence.

FOS2

Frequency of Second component for the second cadence.

FOF3

Frequency of First component for the third cadence.

FOS3

Frequency of Second component for the third cadence.

FOF4

Frequency of First component for the fourth cadence.

FOS4

Frequency of Second component for the fourth cadence.

FOT

Frequency of Third component (in Hertz).

FO4

Frequency of Fourth component (in Hertz).

AOT

Amplitude of Third component (from 1 to 65535 = +3 dBm0).

AO4

Amplitude of Fourth component (from 1 to 65535 = +3 dBm0).

RCT1

Number of repeat for the first cadence.

RCT2

Number of repeat for the second cadence.

RCT3

Number of repeat for the third cadence.

RCT4

Number of repeat for the fourth cadence.

Table 21. show ccm-manager download-tones Output Fields for Sequence Tones

Field of Sequence Tone

Description

DR

Direction to PSTN (0) or Packet Network (1).

NF

Number of Frequency (from 1 to 4).

F1C1

Frequency 1 of Cadence 1.

F2C1

Frequency 2 of Cadence 1.

AOF

Amplitude of First component (from 1 to 65535).

AOS

Amplitude of Second component (from 1 to 65535).

C1ONT

Cadence 1 On Time.

C1OFT

Cadence 1 Off Time.

C2ONT

Cadence 2 On Time.

C2OFT

Cadence 2 Off Time.

C3ONT

Cadence 3 On Time.

C3OFT

Cadence 3 Off Time.

C4ONT

Cadence 4 On Time.

C4OFT

Cadence 4 Off Time.

F1C2

Frequency 1 of Cadence 2.

F2C2

Frequency 2 of Cadence 2.

F1C3

Frequency 1 of Cadence 3.

F2C3

Frequency 2 of Cadence 3.

F1C4

Frequency 1 of Cadence 4.

F2C4

Frequency 2 of Cadence 4.

The following is sample output from the show ccm -manager command for displaying the status and availability of both the primary and the backup Cisco Unified Communications Manager server:


Router# show ccm-manager
MGCP Domain Name: Router2821.cisco.com
Priority        Status                   Host
============================================================
Primary         Registered               10.78.236.222
First Backup    None                     
Second Backup   None                     
Current active Call Manager:    10.78.236.222
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            21:48:37 UTC Nov 4 2007 (elapsed time: 00:00:15)
Last MGCP traffic time:         21:48:51 UTC Nov 4 2007 (elapsed time: 00:00:02)
Last failover time:             None
Last switchback time:           None
Switchback mode:                Graceful
MGCP Fallback mode:             Not Selected
Last MGCP Fallback start time:  None
Last MGCP Fallback end time:    None
MGCP Download Tones:            Disabled 
TFTP retry count to shut Ports: 3
PRI Backhaul Link info:
    Link Protocol:      TCP
    Remote Port Number: 2428
    Remote IP Address:  172.20.71.38
    Current Link State: OPEN
    Statistics:
        Packets recvd:   1
        Recv failures:   0
        Packets xmitted: 3
        Xmit failures:   0
    PRI Ports being backhauled:
       Slot 1, port 1
MGCP Download Tones:             Enabled
Configuration Auto-Download Information
=======================================
Current version-id: {1645327B-F59A-4417-8E01-7312C61216AE}
Last config-downloaded:00:00:49
Current state: Waiting for commands
Configuration Download statistics:
        Download Attempted             : 6
          Download Successful          : 6
          Download Failed              : 0
        Configuration Attempted        : 1
          Configuration Successful     : 1
          Configuration Failed(Parsing): 0
          Configuration Failed(config) : 0
Last config download command: New Registration
Configuration Error History:
FAX mode: cisco

The table below describes the significant fields shown in the display.

Table 22. show ccm-manager Field Descriptions

Field

Description

MGCP Domain Name (system)

System used in the Internet for translating domain names of network nodes into IP addresses.

Priority

Priority of the Cisco CallManager servers present in the network. Possible priorities are primary, first backup, and second backup.

Status

Current usage of the Cisco Unified Communications Manager server. Values are Registered, Idle, Backup Polling, and Undefined.

Host

Host IP address of the Cisco CallManager server.

Current active Call Manager

IP address of the active Cisco Communications Manager server. This field can be the IP address of any one of the following Cisco Communications Manager servers: Primary, First Backup, and Second Backup.

Backhaul/Redundant link port

Port that the Cisco CallManager server is to use.

Failover Interval

Maximum amount of time that can elapse without the gateway receiving messages from the currently active Cisco Call Manager before the gateway switches to the backup Cisco Call Manager.

Keepalive Interval

Interval following which, if the gateway has not received any messages from the currently active Cisco Communications Manager server within the specified amount of time, the gateway sends a keepalive message to the Cisco Communications Manager server to determine if it is operational.

Last keepalive sent

Time in hours (military format), minutes and seconds at which the last keepalive message was sent.

Last MGCP traffic time

Time in hours (military format), minutes and seconds at which the last MGCP traffic message was sent.

Switchback mode

Displays the switchback mode configuration that determines when the primary Cisco CallManager server is used if it becomes available again while a backup Cisco CallManager server is being used.

Values that can appear in this field are Graceful, Immediate, Schedule -time, and Uptime-delay.

MGCP Fallback mode

Displays the MGCP fallback mode configuration. If "Not Selected" displays, then fallback is not configured. If "Enabled/OFF" displays, then fallback is configured but not in effect. If "Enabled/ON" displays, then fallback is configured and in effect.

Last MGCP Fallback start time

Start time stamp in hours (military format), minutes and seconds of the last fallback.

Lasts MGCP Fallback end time

End time stamp in hours (military format), minutes and seconds of the last fallback.

MGCP Download Tones

Displays if the customized tone download is enabled.

TFTP retry count to shut Ports

Number of TFTP download failures allowed before endpoints are shutdown.

The following is sample output from the show ccm-manager config-download command showing the status of the SCCP download:


Router# show ccm-manager config-download
Configuration Auto-Download Information
=======================================
Current version-id:{4171F93A-D8FC-49D8-B1C4-CE33FA8095BF}
Last config-downloaded:00:00:47
Current state:Waiting for commands
Configuration Download statistics:
        Download Attempted             :6
          Download Successful          :6
          Download Failed              :0
        Configuration Attempted        :1
          Configuration Successful     :1
          Configuration Failed(Parsing):0
          Configuration Failed(config) :0
Last config download command:New Registration
SCCP auto-configuration status
===============================================================
Registered with Call Manager: No
Local interface: FastEthernet0/0 (000c.8522.6910)
Current version-id: {D3A886A2-9BC9-41F8-9DB2-0E565CF51E5A}
Current config applied at: 04:44:45 EST Jan 9 2003
Gateway downloads succeeded: 1
Gateway download attempts: 1
Last gateway download attempt:  04:44:45 EST Jan 9 2003
Last successful gateway download: 04:44:45 EST Jan 9 2003
Current TFTP server: 10.2.6.101
Gateway resets: 0
Gateway restarts: 0
Managed endpoints: 6
Endpoint downloads succeeded: 6
Endpoint download attempts: 6
Last endpoint download attempt:  04:44:45 EST Jan 9 2003
Last successful endpoint download: 04:44:45 EST Jan 9 2003
Endpoint resets: 0
Endpoint restarts: 0
Configuration Error History:
sccp ccm CCM-PUB7 identifier 1
end
controller T1 2/0no shut
controller T1 2/0no shut
controller T1 2/0no shut
isdn switch-type primary-ni
end

The table below describes the significant fields shown in the display.

Table 23. show ccm-manager config-download Field Descriptions

Field

Description

Current state

Current configuration state.

Download Attempted

Number of times the gateway has tried to download the configuration file. The number of successes and failures is displayed.

Configuration Attempted

Number of times the gateway has tried to configure the gateway based on the configuration file. The number of successes and failures is displayed.

Managed endpoints

Number of SSCP-controlled endpoints (analog and BRI phones).

Endpoint downloads succeeded

Number of times the gateway has successfully downloaded the configuration files for SCCP-controlled endpoints.

Endpoint download attempts

Number of times the gateway has tried to download the configuration files for SCCP-controlled endpoints.

Endpoint resets

Number of SCCP gateway resets.

Endpoint restarts

Number of SCCP gateway restarts.

Configuration Error History

Displays SCCP autoconfiguration errors.

The following is sample output from the show ccm-manager fallback-mgcp command:


Router# show ccm-manager fallback-mgcp
Current active Call Manager:   172.20.71.38
MGCP Fallback mode:            Enabled/OFF
Last MGCP Fallback start time: 00:14:35
Last MGCP Fallback end time:   00:17:25

The table below displays te mode. Modes are as follows:

Table 24. show ccm-manager fallback-mgcp modes

Field

Description

MGCP Fallback mode

The following are displayed:

  • Not Selected--Fallback is not configured.

  • Enabled/OFF--Fallback is configured but not in effect.

  • Enabled/ON--Fallback is configured and in effect.

Last MGCP Fallback start time

Start time stamp in hh:mm:ss of the last fallback.

Last MGCP Fallback end time

End time stamp in hh:mm:ss of the last fallback.

The following is sample output from the show ccm-manager music-on-hold command:


Router# show ccm-manager music-on-hold
Current active multicast sessions :1
 Multicast       RTP port   Packets       Call   Codec    Incoming
 Address         number     in/out        id              Interface
===================================================================
172.20.71.38     2428        5/5          99      g711

The table below describes the significant fields shown in the display.

Table 25. show ccm-manager music-on-hold Field Descriptions

Field

Description

Current active multicast sessions

Number of active calls on hold.

Multicast Address

Valid class D address from which the gateway is getting the RTP streams.

RTP port number

Valid RTP port number on which the gateway receives the RTP packets.

Packets in/out

Number of RTP packets received and sent to the digital signal processor (DSP).

Call id

Call ID of the call that is on hold.

Codec

Codec number.

Incoming Interface

Interface through which the gateway is receiving the RTP stream.

show cdapi

To display the Call Distributor Application Programming Interface (CDAPI), use the show cdapi command in privileged EXEC mode.

show cdapi

Syntax Description

This command has no arguments or keywords.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(7)T

This command was introduced on the Cisco AS5300.

12.3(4)T

This command was enhanced to display V.120 call types registering with the modem.

Usage Guidelines

CDAPI is the internal application programming interface (API) that provides an interface between signaling stacks and applications.

Examples

The following is sample output from the show cdapi command. The output displays the following information:

  • Signaling stacks that register with CDAPI

  • Applications that register with CDAPI

  • Active calls

  • Call type of each active call

  • Message buffers in use


Router# show cdapi
Registered CDAPI Applications/Stacks
====================================
Signaling Stack: ISDN
        Interface: Se6/0:23
Application: TSP CDAPI Application Voice
        Application Type(s) : Voice Data Facility Signaling V110 V120
        Application Level   : Tunnel
        Application Mode    : Enbloc
Application: TSP CDAPI Application COT
        Application Type(s) : Cot
        Application Level   : Tunnel
        Application Mode    : Enbloc
Application: CSM
        Application Type(s) : Modem V110 V120
        Application Level   : Basic
        Application Mode    : Enbloc
Signaling Stack: XCSP
Application: dialer
        Application Type(s) : Data
        Application Level   : Basic
        Application Mode    : Enbloc
Active CDAPI Calls
==================
        Se7/7:23 Call ID = 0x7717, Call Type = V.120, Application = CSM
CDAPI Message Buffers
=====================
Free Msg Buffers: 320
Free Raw Buffers: 320
Free Large-Raw Buffers: 120

Field descriptions should be self-explanatory. However, the following information may be of help:

  • Enbloc is the mode where all call-establishment information is sent in the setup message (opposite of overlap mode, where additional messages are needed to establish the call).

  • Cot is the Continuity Test (COT) subsystem that supports the continuity test required by the Signaling System 7 (SS7) network to conduct loopback and tone check testing on the path before a circuit is established.

show ces clock-select

To display the setting of the network clock for the specified port, use the show ces clock -select command in privileged EXEC mode.

show ces slot/port clock-select

Syntax Description

slot

Backplane slot number.

/port

Interface port number. The slash must be entered.

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.1(2)T

This command was introduced on the Cisco 3600 series.

Examples

The following is sample output from this command for slot 1, port 0:


Router# show ces 1/0 clock-select
Priority 1 clock source:not configured
Priority 2 clock source:not configured
Priority 3 clock source:ATM1/0 UP
Priority 4 clock source:Local oscillator
Current clock source:ATM1/0, priority:3

Field descriptions should be self-explanatory.

show connect

To display configuration information about drop-and-insert connections that have been configured on a router, use the show connect command in privileged EXEC mode.

show connect {all | elements | name | id | port {T1 | E1}slot/port}

Syntax Description

all

Information for all configured connections.

elements

Information for registered hardware or software interworking elements.

name

Information for a connection that has been named by using the connect global configuration command. The name you enter is case sensitive and must match the configured name exactly.

id

Information for a connection that you specify by an identification number or range of identification numbers. The router assigns these IDs automatically in the order in which they were created, beginning with 1. The show connect all command displays these IDs.

port

Information for a connection that you specify by indicating the type of controller (T1 or E1) and location of the interface.

T1

T1 controller.

E1

E1 controller.

slot/port

Location of the T1 or E1 controller port whose connection status you want to see. Valid values for slot and port are 0 and 1 . The slash must be entered.

Command Default

No default behavior or values

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(5)XK

This command was introduced on the Cisco 2600 series and Cisco 3600 series.

12.0(7)T

This command was integrated into Cisco IOS Release 12.0(7)T.

Usage Guidelines

This command shows drop-and-insert connections on modular access routers that support drop-and-insert. It displays different information in different formats, depending on the keyword that you use.

Examples

The following examples show how the same tabular information appears when you enter different keywords:


Router# show connect all
ID   Name               Segment 1            Segment 2           State
========================================================================
1    Test              -T1 1/0 01           -T1 1/1 02           ADMIN UP
2    Test2             -T1 1/0 03           -T1 1/1 04           ADMIN UP
Router# show connect id 1-2
ID   Name               Segment 1            Segment 2           State
========================================================================
1    Test              -T1 1/0 01           -T1 1/1 02           ADMIN UP
2    Test2             -T1 1/0 03           -T1 1/1 04           ADMIN UP
Router# show connect port t1 1/1
ID   Name               Segment 1            Segment 2           State
========================================================================
1    Test              -T1 1/0 01           -T1 1/1 02           ADMIN UP
2    Test2             -T1 1/0 03           -T1 1/1 04           ADMIN UP

The following examples show details about specific connections, including the number of time slots in use and the switching elements:


Router# show connect id 2
Connection: 2 - Test2
 Current State: ADMIN UP
 Segment 1: -T1 1/0 03
  TDM timeslots in use: 14-18 (5 total)
 Segment 2: -T1 1/1 04
  TDM timeslots in use: 14-18
Internal Switching Elements: VIC TDM Switch
Router# show connect name Test
 Connection: 1 - Test
 Current State: ADMIN UP
 Segment 1: -T1 1/0 01
  TDM timeslots in use: 1-13 (13 total)
 Segment 2: -T1 1/1 02
  TDM timeslots in use: 1-13
Internal Switching Elements: VIC TDM Switch

Field descriptions should be self-explanatory.

show controllers rs366

To display information about the RS-366 video interface on the video dialing module (VDM), use the show controllers rs366 command in privileged EXEC mode.

show controllers rs366 slot port

Syntax Description

slot

Slot location of the VDM module. Valid entries are 1 or 2.

port

Port location of the EIA/TIA-366 interface in the VDM module.

Command Default

No default behavior or values

Command Modes


Privileged EXEC (#)

Command History

Release

Modification

12.0(5)XK