Cisco Remote PHY Shelf 7200 Command Reference

show platform diag

To view your RPHY diagnostics, use the show platform diag command in privileged EXEC mode.

show platform diag

Command Default

None.

Command Modes

Privileged EXEC (#) (FCC and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show platform diag command:

HA-Shelf-FCC# show platform diag
Chassis type: HA-RPHY-CHASSIS

HA-RPHY-FAN-TRAY:
	State                       : OK
	Software declared up time   : 2 days, 7 hours, 20 minutes, 20 seconds
	Primary UBoot               : 181019 *
	Golden UBoot                : 180508
	IOFPGA version              : a209 (Primary)
	EOBC version                : 1.01

PIC0, HA-RPHY-PIC
	State                       : OK

PIC1, HA-RPHY-PIC
	State                       : OK

P0, CBR-AC-PS
	State                       : OK

FAN0, UNKNOWN
	State                       : NORMAL
	Physical insert detect time : 2 days, 7 hours, 18 minutes, 18 seconds

FAN1, UNKNOWN
	State                       : NORMAL
	Physical insert detect time : 2 days, 7 hours, 18 minutes, 18 seconds

LC1, HA-RPHY-6x12-LC:
	State                       : OK
	Software declared up time   : 6 hours, 37 minutes, 50 seconds
	Primary UBoot               : 2017.11 (Aug 17 2018 - 08:43:42 +0800) *
	Golden UBoot                : 2016.01 (Apr 17 2018 - 03:00:31 +0800)
	FPGA version                : 2.3.15
	IOFPGA version              : 0x8229
	ADM1266-0 firmware version  : 010d02
	ADM1266-0 config version    : A23
	ADM1266-1 firmware version  : 010d02
	ADM1266-1 config version    : A23
	ADM1266-2 firmware version  : 010d02
	ADM1266-2 config version    : A23
	JPLD version                : 0x1

LC12, UNKNOWN:
	State                       : OK
	Software declared up time   : 6 hours, 19 minutes, 45 seconds
	Primary UBoot               : 2017.11 (Aug 17 2018 - 08:43:42 +0800) *
	Golden UBoot                : 2017.11 (Jun 11 2018 - 02:17:47 +0800)
	FPGA version                : 2.3.15
	IOFPGA version              : 0xc129
	ADM1266-0 firmware version  : 010a04
	ADM1266-0 config version    : A14
	ADM1266-1 firmware version  : 010a04
	ADM1266-1 config version    : A14
	ADM1266-2 firmware version  : 010a04
	ADM1266-2 config version    : A14
	JPLD version                : 0x2

show pm

To view packet count received on a specific port, use the show erpd command in privileged EXEC mode.

show pm index_id statistic port port_id

Syntax Description


`index_id`	Displays the information of a specific eRPD.
port `port_id`	Displays the information of a specific port.

Command Default

None.

Command Modes

Privileged EXEC (#) (Line Card, Primary eRPD, and Non-Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

The following is a sample output of the show pm command:

HA-Shelf-Slot-0# show pm 5 statistic port 1
Port 1
RX unsupported opcode frames        : 0x0
RX frames (all packets)             : 0x6dddbee
RX pause frames                     : 0x0
RX control frames                   : 0x0
RX undersized frames                : 0x0
RX truncated frames (FIFO full)     : 0x0
RX bytes                            : 0x0
RX good frames                      : 0x6dddbfc
RX MTU check error frames           : 0x0
RX jabber frames                    : 0x0
RX fragment                         : 0x0
RX out-of-range length frames       : 0x0
RX FCS error frames                 : 0x0
RX false carrier                    : 0x0
RX code error frames                : 0x0
RX alignment error                  : 0x0
TXCL                                : 0x1a5
TX FIFO underrun                    : 0x0
TX UC frames                        : 0x1d87b3
TX runt packets                     : 0x0
TX good frames                      : 0x1da692
TX frames (all packets)             : 0x1da692
TX oversized frames                 : 0x0
TNCL                                : 0x0
TX jabber                           : 0x0
TX runt packet with invalid FCS     : 0x0
TX FCS error                        : 0x0
TX error frames                     : 0x0
TX bytes                            : 0xc8bab74
TX BC frames                        : 0xae3

show process

To view your CPU, disk, and memory utillization, use the show process command in privileged EXEC mode.

show process {cpu | mem}

Command Default

None.

Command Modes

Privileged EXEC (#) (FCC and Line Card)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show process cpu command:

HA-Shelf-FCC# show process cpu

CPU Utilization 2.125%, CPU0  2.5%, CPU1  1.5%, CPU2  2.5%, CPU3  2.0%
  PID %MEM %CPU   VSZ/M   RSS/M TTY           COMMAND
    1  0.1  0.0       2       1 ?             /sbin/procd
    2  0.0  0.0       0       0 ?             kthreadd
    4  0.0  0.0       0       0 ?             kworker/0:0H
    6  0.0  0.0       0       0 ?             mm_percpu_wq
    7  0.0  0.0       0       0 ?             ksoftirqd/0
    8  0.0  0.0       0       0 ?             rcu_preempt
    9  0.0  0.0       0       0 ?             rcu_sched
   10  0.0  0.0       0       0 ?             rcu_bh
   11  0.0  0.0       0       0 ?             migration/0
   12  0.0  0.0       0       0 ?             cpuhp/0
   13  0.0  0.0       0       0 ?             cpuhp/1
   14  0.0  0.0       0       0 ?             migration/1
   15  0.0  0.0       0       0 ?             ksoftirqd/1
   16  0.0  0.0       0       0 ?             kworker/1:0
   17  0.0  0.0       0       0 ?             kworker/1:0H
   18  0.0  0.0       0       0 ?             cpuhp/2
   19  0.0  0.0       0       0 ?             migration/2
   20  0.0  0.0       0       0 ?             ksoftirqd/2
   21  0.0  0.0       0       0 ?             kworker/2:0
   22  0.0  0.0       0       0 ?             kworker/2:0H
   23  0.0  0.0       0       0 ?             cpuhp/3
   24  0.0  0.0       0       0 ?             migration/3
   25  0.0  0.0       0       0 ?             ksoftirqd/3
   26  0.0  0.0       0       0 ?             kworker/3:0
   27  0.0  0.0       0       0 ?             kworker/3:0H
   28  0.0  0.0       0       0 ?             netns
   43  0.0  0.0       0       0 ?             kworker/3:1
   61  0.0  0.0       0       0 ?             kworker/1:1
   64  0.0  0.0       0       0 ?             kworker/0:1
   69  0.0  0.0       0       0 ?             kworker/2:1

This is a sample output of the show process mem command:

HA-Shelf-FCC# show process cpu
Disk Utilization (in kBytes)
Dev                  Mount                     Total       Used      %
/dev/root            /                        259856     160328   63.0
/dev/mmcblk0p1       /bootflash              2063184    1372496   70.0
/dev/mmcblk0p2       /fcc                    5160416    1236276   25.0
/dev/mmcblk0p3       /obfl                     92219      10345   12.0
/dev/loop0           /bootflash/corefiles     588352     126344   23.0

Memory Utilization (in kBytes)
Total  1861576, Available 1337616, Percent    28.1%, Used    865552, Free  996024
Active  444124, Inactive   106228, Buffers     3268, Cached  338324, Shared   23512
   pid      %     vsz     rss  shared    text    data cmd
     1    0.1    2660    1692    1388      52     536 /sbin/procd
     2    0.0       0       0       0       0       0 kthreadd
     4    0.0       0       0       0       0       0 kworker/0:0H
     6    0.0       0       0       0       0       0 mm_percpu_wq
     7    0.0       0       0       0       0       0 ksoftirqd/0
     8    0.0       0       0       0       0       0 rcu_preempt
     9    0.0       0       0       0       0       0 rcu_sched
    10    0.0       0       0       0       0       0 rcu_bh
    11    0.0       0       0       0       0       0 migration/0
    12    0.0       0       0       0       0       0 cpuhp/0
    13    0.0       0       0       0       0       0 cpuhp/1
    14    0.0       0       0       0       0       0 migration/1
    15    0.0       0       0       0       0       0 ksoftirqd/1
    16    0.0       0       0       0       0       0 kworker/1:0
    17    0.0       0       0       0       0       0 kworker/1:0H
    18    0.0       0       0       0       0       0 cpuhp/2
    19    0.0       0       0       0       0       0 migration/2
    20    0.0       0       0       0       0       0 ksoftirqd/2
    21    0.0       0       0       0       0       0 kworker/2:0
    22    0.0       0       0       0       0       0 kworker/2:0H
    23    0.0       0       0       0       0       0 cpuhp/3
    24    0.0       0       0       0       0       0 migration/3
    25    0.0       0       0       0       0       0 ksoftirqd/3
    26    0.0       0       0       0       0       0 kworker/3:0
    27    0.0       0       0       0       0       0 kworker/3:0H
    28    0.0       0       0       0       0       0 netns
    43    0.0       0       0       0       0       0 kworker/3:1
    61    0.0       0       0       0       0       0 kworker/1:1
    64    0.0       0       0       0       0       0 kworker/0:1
    69    0.0       0       0       0       0       0 kworker/2:1

show provision

To display information on all the CCAP cores, use the show provision command in privileged EXEC mode.

show provision [all | [ccap-core ccap-core index | gcp {ccap-identification | conn-verification } | history | manager [history] | message-history | state ]]

Syntax Description


all	Displays information on all CCAP cores.
ccap-core ccap-core index
gcp ccap-identification	Displays information on the provision GCP CCAP-identification.
gcp connection verification parameters	Displays information on the provision gcp conn-verification parameters.
history	Displays information on the core provision history.
manager	Displays information on the provision manager state information.
manager history	Displays information on the provision manager state change history.
message-history	Dispalys information on the provision agent state change history.
state	Displays the RPD state information.

Command Default

None.

Command Modes

Privileged EXEC (#) (Non-Primary eRPD and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

The following are sample output of the show provision all command:

HA-Shelf-eRPD-0/0# show provision all
Core-Index  ID               Interface  IP             Name      State        Role       Core-Mode  Initiated-By           
0           CORE-2274803641  vbh3       120.102.22.17  CCAPCORE  online       Principal  Active     DHCP                   
None        CORE-1741190364  vbh3       120.102.22.37  NA        init(ipsec)                        Provision_operational

HA-Shelf-eRPD-0/0# show provision ccap-core ccap-core index
Index  CoreId        CoreIpAddress          IsPrincipal  CoreMode              CoreFunction  
1      a0f8496b4a83  2001:120:102:22:2::17  True         CoreModeOutOfService  223           
0      a0f8496b4a83  120.102.22.17          True         CoreModeActive        223           
F02-Shelf-eRPD-1/3#show provision gcp ccap-identification
ccap-identification  ccap-core redis db information

HA-Shelf-eRPD-0/0# show provision gcp ccap-identification
Index  CoreId        CoreIpAddress          IsPrincipal  CoreMode              CoreFunction  
1      a0f8496b4a83  2001:120:102:22:2::17  True         CoreModeOutOfService  223           
0      a0f8496b4a83  120.102.22.17          True         CoreModeActive        223           
F02-Shelf-eRPD-1/3#show provision gcp ccap-identification
ccap-identification  ccap-core redis db information

HA-Shelf-eRPD-0/0# show provision gcp conn-verification
CoreId        MaxGcpIdleTime  GcpRecoveryAction          GcpRecoveryActionRetry  GcpRecoveryActionDelay  GcpReconnectTimeout  
a0f8496b4a83  0               GcpReconnectToTheSameCore  3                       30                      30

HA-Shelf-eRPD-0/0# show provision history
Core-Index  Interface  IP             Mac                From-State         To-State           event                Added-By  Time                         
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  none               init(ipsec)        TRIGGER_Startup      DHCP      2019 Jan 22 00:35:17:585587  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:35:17:588386  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:35:19:076017  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:35:19:096427  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:35:49:103136  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:35:51:132740  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:35:51:158225  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:36:21:163149  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:36:23:169938  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:36:23:191646  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:36:53:202184  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:36:55:204878  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:36:55:225806  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        FAIL               TRIGGER_Error        DHCP      2019 Jan 22 00:36:55:262577  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  FAIL               DEL                TRIGGER_DEL          DHCP      2019 Jan 22 00:36:55:295124  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  none               init(ipsec)        TRIGGER_Startup      DHCP      2019 Jan 22 00:38:17:602204  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:38:17:605676  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:38:19:394182  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:38:19:414651  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:38:49:425994  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:38:51:435812  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:38:51:455711  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:39:21:463361  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:39:23:462831  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:39:23:482484  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:39:53:485051  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:39:55:510051  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:39:55:532824  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        FAIL               TRIGGER_Error        DHCP      2019 Jan 22 00:39:55:571848  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  FAIL               DEL                TRIGGER_DEL          DHCP      2019 Jan 22 00:39:55:607530  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  none               init(ipsec)        TRIGGER_Startup      DHCP      2019 Jan 22 00:41:17:598949  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:41:17:601737  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:41:18:667984  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:41:18:694449  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:41:48:703604  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:41:49:763436  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:41:49:784501  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:42:19:793378  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:42:20:884378  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:42:20:909116  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:42:50:922675  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:42:52:085139  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:42:52:108127  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        FAIL               TRIGGER_Error        DHCP      2019 Jan 22 00:42:52:150245  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  FAIL               DEL                TRIGGER_DEL          DHCP      2019 Jan 22 00:42:52:187436  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  none               init(ipsec)        TRIGGER_Startup      DHCP      2019 Jan 22 00:44:17:608804  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 22 00:44:17:611263  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 22 00:44:19:288293  
None        vbh3       120.102.22.37  ba:db:ad:17:0c:43  init(gcp-ira)      init(ipsec)        TRIGGER_TCP_FAIL     DHCP      2019 Jan 22 00:44:19:309643  
None        vbh3       120.102.22.17  ba:db:ad:17:0c:43  none               init(ipsec)        TRIGGER_Startup      DHCP      2019 Jan 21 16:59:05:425927  
None        vbh3       120.102.22.17  ba:db:ad:17:0c:43  init(ipsec)        init(tcp)          TRIGGER_IPSEC_OK     DHCP      2019 Jan 21 16:59:05:429235  
None        vbh3       120.102.22.17  ba:db:ad:17:0c:43  init(tcp)          init(gcp-ira)      TRIGGER_TCP_OK       DHCP      2019 Jan 21 16:59:06:796445  
None        vbh3       120.102.22.17  ba:db:ad:17:0c:43  init(gcp-ira)      init(gcp-cfg)      TRIGGER_GCP_IRA      DHCP      2019 Jan 21 16:59:06:893914  
0           vbh3       120.102.22.17  ba:db:ad:17:0c:43  init(gcp-cfg)      init(gcp-cfg-cpl)  TRIGGER_GCP_CFG      DHCP      2019 Jan 21 16:59:07:143812  
0           vbh3       120.102.22.17  ba:db:ad:17:0c:43  init(gcp-cfg-cpl)  init(gcp-op)       TRIGGER_GCP_CFG_CPL  DHCP      2019 Jan 21 16:59:15:635490  
0           vbh3       120.102.22.17  ba:db:ad:17:0c:43  init(gcp-op)       online             TRIGGER_GCP_OP       DHCP      2019 Jan 21 16:59:16:966356

HA-Shelf-eRPD-0/0# show provision manager
ID              State        Time                         
MGR-3526216643  OPERATIONAL  2019 Jan 21 16:59:16:957446

HA-Shelf-eRPD-0/0# show provision message-history
  ID              From-State           To-State             Event              Time                         
MGR-1833250024  none                 INIT                 Startup            2019 Jan 24 14:45:02:412139  
MGR-1833250024  INIT                 PRINCIPLE_PROVISION  STARTUP_TOD_OK     2019 Jan 24 14:45:17:481874  
MGR-1833250024  PRINCIPLE_PROVISION  PRINCIPAL_FOUND      SEEK_PRINCIPAL_OK  2019 Jan 24 14:45:53:720551  
MGR-1833250024  PRINCIPAL_FOUND      OPERATIONAL          OPERATIONAL_OK     2019 Jan 24 14:46:07:741142

HA-Shelf-eRPD-0/0# show provision state
TopLevelRpdstate:             OperationalPrincipalCore
ConnectPrincipalCoreSubState: GcpConfigPrincipalCore
LocalPtpSyncStatus:           True

NetworkAuthenticationPortIndex  NetworkAuthenticationRpdState  
4                               WaitForEapReq                  


AuxCoreIndex  AuxCoreId  AuxCoreIp  AuxCoreRPDState

show ptp clock

To display information on the PTP clock of the Line Card, use the show ssh command in privileged EXEC mode.

show ptp clock { session | rpd-pubkey}

Command Default

None.

Command Modes

Privileged EXEC (#) (Non-Primary eRPD and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.x	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

The following is a sample output of the show ptp clock command:

HA-Shelf-eRPD-0/0# show ptp clock 0 state 
apr state       : PHASE_LOCK
clock state     : CLOCK_VERIFY
current tod     : 1539406121   Sat Oct 13 04:48:41 2018
active stream   : 2
==stream    2   :
  port id       :                1
  master ip     :       10.90.3.93
  local ip      :       90.0.21.12
  stream state  :       PHASE_LOCK
  Master offset :             -655
  Path    delay :            14256
  Forward delay :            13601
  Reverse delay :            14846
  Freq offset   :           -57294
  1Hz  offset   :              802
==stream    4   :
  port id       :                2
  master ip     :       10.90.3.93
  local ip      :       90.0.22.12
  stream state  :       PHASE_LOCK
  Master offset :             -640
  Path    delay :            14317
  Forward delay :            13677
  Reverse delay :            14871
  Freq offset   :           -57083
  1Hz  offset   :              796
==stream    6   :
  port id       :                3
  master ip     :       10.90.3.93
  local ip      :       90.0.23.12
  stream state  :       PHASE_LOCK
  Master offset :             -446
  Path    delay :            14757
  Forward delay :            13759
  Reverse delay :            15756
  Freq offset   :           -57354
  1Hz  offset   :              833
==stream    8   :
  port id       :                4
  master ip     :       10.90.3.93
  local ip      :       90.0.20.12
  stream state  :       PHASE_LOCK
  Master offset :             -870
  Path    delay :            14398
  Forward delay :            13793
  Reverse delay :            15003
  Freq offset   :           -57427
  1Hz  offset   :              817

show reboot hold

To display information on what is blocking the system from reboot, use the show reboot hold command in privileged EXEC mode.

show reboot hold

Command Default

None.

Command Modes

Privileged EXEC (#) (Non-Primary eRPD and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

The following is a sample output of the show reboot hold command:

HA-Shelf-eRPD-0/0# show reboot hold
PC_REBOOT_HOLD is not set

show running-config

To view port mapping and link redundancy details on the Cisco Remote PHY Shelf 7200, use the show running-config command in privileged EXEC mode.

show running-config [ bh-erpd-mapping | link-redundancy ]

Syntax Description


bh-erpd-mapping	Displays the SFP+ port mapping to RPHY devices.
link-redundancy	Displays the link redundancy mode.

Command Default

None.

Command Modes

Privileged EXEC (#) (FCC, Line Card, and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show running-config command:

HA-Shelf-FCC# show running-config
Building configuration...
!
hostname prefix 66666666666666666666 
!
login password 21232f297a57a5a7438 
!
over-temp-shutdown  
!
trunk vlan 423 slot 1 erpd 0 
trunk vlan 423 slot 1 erpd 1 
trunk vlan 423 slot 1 erpd 2 
trunk vlan 423 slot 1 erpd 3 
trunk vlan 423 slot 1 erpd 4 
trunk vlan 423 slot 1 erpd 5 
trunk vlan 100 slot 5 erpd 2 
trunk vlan 100 slot 5 erpd 3 
trunk vlan 100 slot 5 erpd 4 
trunk vlan 423 slot 12 erpd 0 
trunk vlan 423 slot 12 erpd 1 
trunk vlan 423 slot 12 erpd 2 
trunk vlan 423 slot 12 erpd 3 
trunk vlan 423 slot 12 erpd 4 
trunk vlan 423 slot 12 erpd 5 
!
mgmt ip 80.4.1.8 netmask 255.255.255.0 gateway 80.4.1.1 
!
bh-erpd-mapping backhaul 0 erpd 0
bh-erpd-mapping backhaul 1 erpd 1
bh-erpd-mapping backhaul 2 erpd 2
bh-erpd-mapping backhaul 4 erpd 3
bh-erpd-mapping backhaul 5 erpd 4
bh-erpd-mapping backhaul 6 erpd 5
!
link-redundancy mode 6+2
!

This is a sample output of the show running-config bh-erpd-mapping command:

HA-Shelf-FCC# show running-config bh-erpd-mapping
Building configuration...
!
bh-erpd-mapping backhaul 0 erpd 0
bh-erpd-mapping backhaul 1 erpd 1
bh-erpd-mapping backhaul 2 erpd 2
bh-erpd-mapping backhaul 4 erpd 3
bh-erpd-mapping backhaul 5 erpd 4
bh-erpd-mapping backhaul 6 erpd 5

This is a sample output of the show running-config link-redundancy command:

HA-Shelf-FCC# show running-config link-redundancy
Building configuration...
!
link-redundancy mode 6+2

show sfp info

To display general information about an SFP+ port , use the show sfp info command in privileged EXEC mode.

show sfp info port

Syntax Description


`port`	Specifies the port number.

Command Default

None.

Command Modes

Privileged EXEC (#) (Line Card)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show sfp info command for all the line cards:

HA-Shelf-Slot-0# show sfp info
== SFP A0 EEPROM CONTENT ==
Reg 0x0000: 03 04 07 10 00 00 00 00  00 00 00 06 67 00 00 00 
Reg 0x0010: 08 02 00 1e 43 49 53 43  4f 2d 46 49 4e 49 53 41 
Reg 0x0020: 52 20 20 20 00 00 90 65  46 54 4c 58 38 35 37 34 
Reg 0x0030: 44 33 42 43 4c 2d 43 53  41 20 20 20 03 52 00 c9 
Reg 0x0040: 00 1a 00 00 46 4e 53 32  31 34 38 30 42 56 55 20 
Reg 0x0050: 20 20 20 20 31 37 31 31  32 38 20 20 68 80 05 ee 
Reg 0x0060: 00 00 02 e7 e9 e6 51 74  36 82 8d 94 b2 8e dd fb 
Reg 0x0070: d6 15 07 00 00 00 00 00  00 00 00 00 36 7a 3d 6e 
Identifier      :0x3
Ext.Identifier  :0x4
Connector       :0x7
Compliance Code :0x10
Encoding        :0x6
BR,Nominal      :0x67
Rate Identifier :0x0
Length(9um)-km  :0x0
Length(9um)     :0x0
Length(50 um)   :0x8
Length(62.5 um) :0x2
Length(Copper)  :0x0
Length(OM3)     :0x1e
Vendor name     :CISCO-FINISAR   
Vendor OUI      :0x0 0x90 0x65 
Vendor PN       :FTLX8574D3BCL-CS
Vendor Rev      :A   
Wavelength      :850
CC Base         :0xc9
SN              :FNS21480BVU  
== SFP A2 EEPROM CONTENT ==
CLEI            :COUIA8NCAA
PN              :10-2415-03
PID             :SFP-10G-SR          
Reg 0x0000: 4b 00 fb 00 46 00 00 00  8d cc 74 04 87 5a 7a 76 
Reg 0x0010: 19 64 07 d0 18 6a 09 c4  39 c7 02 e5 1c f5 07 46 
Reg 0x0020: 3d e9 01 97 1f 07 03 ff  00 00 00 00 00 00 00 00 
Reg 0x0030: 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
Reg 0x0040: 00 00 00 00 3f 80 00 00  00 00 00 00 01 00 00 00 
Reg 0x0050: 01 00 00 00 01 00 00 00  01 00 00 00 00 00 00 bf 
Reg 0x0060: 1f 30 80 69 10 e9 17 38  13 f7 00 00 00 00 30 00 
Reg 0x0070: 00 00 00 00 00 00 00 00  ff ff ff ff ff ff ff 01 
Reg 0x0080: 43 4f 55 49 41 38 4e 43  41 41 31 30 2d 32 34 31 
Reg 0x0090: 35 2d 30 33 56 30 33 20  01 00 46 00 00 00 00 c6 
Reg 0x00a0: 00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00 
Reg 0x00b0: 00 00 00 00 00 00 00 00  00 00 00 00 00 00 aa aa 
Reg 0x00c0: 53 46 50 2d 31 30 47 2d  53 52 20 20 20 20 20 20 
Reg 0x00d0: 20 20 20 20 34 38 00 00  00 00 00 00 00 00 00 3c 
Reg 0x00e0: 1e 20 2a 2a 31 34 29 36  00 00 00 00 00 00 00 00 
Reg 0x00f0: 00 00 00 00 00 56 00 00  ff ff ff ff 00 00 00 00

show ssh

To display information on the SSH sessions, use the show ssh command in privileged EXEC mode.

show ssh { session | rpd-pubkey}

Command Default

None.

Command Modes

Privileged EXEC (#) (Non-Primary eRPD and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.x	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

The following is a sample output of the show ssh command:

HA-Shelf-FCC# show ssh session
connected session: 1
ssh password auth: on
ssh NMS pubkey num: 0

HA-Shelf-FCC# show ssh rpd-pubkey
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCMXf/DNGyOi/UHAG8g+d3XTnIDnvW2r1PTe/gaihzx7IEZHhVPr1RJjNIaK9t7Zx9Ps3+v4SrBg5SA3HxxyAuvlQfw0kbrJZvumXbGxtnp3dOXj0hC8ogQmKMp4I/rSoQVQk6Z/OvgCG9WplMpRfv+FxhazYnEQbj+dLReTgJGIikR7Uja8lpPQhJ+Czm+iSHlZO5XuQA9gexslClL9Mmu64YoDqUfJyKxe8+P8wjaOEoYuGrjCPxz/2ps6THuyxdi1863C710qGOe8nIiXHkYQNem7fSwI7rcBFqBfQ7bSNnIrVCDvQU2Ly/eTQ6oYVsG9zn4FJjkWRyU7pdr4Wh9 root@RPDBADBAD170C40
Fingerprint: md5 91:36:e5:4e:db:20:da:d5:e3:8f:3b:60:23:7a:57:66
F02-Shelf-eRPD-1/3#show ssh rpd-pubkey

show startup-config

To display the currently saved configuration, use the show startup-config command in privileged EXEC mode.

show startup-config

Command Default

None.

Command Modes

Privileged EXEC (#) (FCC, Line Card, and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show startup-config command for all the line cards:

HA-Shelf-FCC# show startup-config
!
hostname prefix F02-Shelf 
!
login password 21232f297a57a5a743894a0e4a801fc3 
!
over-temp-shutdown enable 
!
trunk vlan 423 slot 0 erpd 0 
trunk vlan 423 slot 0 erpd 1 
trunk vlan 423 slot 0 erpd 2 
trunk vlan 423 slot 0 erpd 3 
trunk vlan 423 slot 0 erpd 4 
trunk vlan 423 slot 0 erpd 5 
trunk vlan 423 slot 1 erpd 0 
trunk vlan 423 slot 1 erpd 1 
trunk vlan 423 slot 1 erpd 2 
trunk vlan 423 slot 1 erpd 3 
trunk vlan 423 slot 1 erpd 4 
trunk vlan 423 slot 1 erpd 5 
!
mgmt ip 80.4.1.7 netmask 255.255.255.0 gateway 80.4.1.1 
!
bh-erpd-mapping backhaul 0 erpd 0
bh-erpd-mapping backhaul 1 erpd 1
bh-erpd-mapping backhaul 2 erpd 2
bh-erpd-mapping backhaul 3 erpd 3
bh-erpd-mapping backhaul 4 erpd 4
bh-erpd-mapping backhaul 5 erpd 5
!
link-redundancy mode N/A
!

show static l2tp

To display information on the static Layer 2 VPN, use the show static l2tp command in privileged EXEC mode.

show static l2tp {tunnels | session | session link}

Syntax Description


session	Displays information on the static Layer 2 VPN session.
session link	Displays information on the static Layer 2 VPN session link.
tunnels	Displays information on the Layer 2 VPN static tunnels.

Command Default

None.

Command Modes

Privileged EXEC (#) (Non-Primary eRPD and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

The following is a sample output of the show static l2tp command:

HA-Shelf-eRPD-0/0# show static l2tp
2019-01-22 00:33:16,663-cmd_ios.py-1114-ERROR-cli error:'module' object has no attribute 'STATIC_SYSTEM_INFO'
2019-01-22 00:33:16,665-cmd_ios.py-1115-WARNING-Traceback (most recent call last):
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1111, in cmdloop
    stop = self.onecmd(line)
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1051, in onecmd
    stop = func()
  File "/usr/lib/python2.7/site-packages/cli/l2tp_cli/l2tp_cli.py", line 192, in show_static_l2tp
    system_type= l2tpMsg.STATIC_SYSTEM_INFO
AttributeError: 'module' object has no attribute 'STATIC_SYSTEM_INFO'

HA-Shelf-eRPD-0/0# show static l2tp session
2019-01-22 00:30:45,677-cmd_ios.py-1114-ERROR-cli error:'module' object has no attribute 'STATIC_SYSTEM_INFO'
2019-01-22 00:30:45,679-cmd_ios.py-1115-WARNING-Traceback (most recent call last):
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1111, in cmdloop
    stop = self.onecmd(line)
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1051, in onecmd
    stop = func()
  File "/usr/lib/python2.7/site-packages/cli/l2tp_cli/l2tp_cli.py", line 283, in show_static_l2tp_session
    system_type = l2tpMsg.STATIC_SYSTEM_INFO
AttributeError: 'module' object has no attribute 'STATIC_SYSTEM_INFO'

HA-Shelf-eRPD-0/0# show static l2tp session link
2019-01-22 23:26:28,614-cmd_ios.py-1114-ERROR-cli error:'module' object has no attribute 'STATIC_SYSTEM_INFO'
2019-01-22 23:26:28,621-cmd_ios.py-1115-WARNING-Traceback (most recent call last):
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1111, in cmdloop
    stop = self.onecmd(line)
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1051, in onecmd
    stop = func()
  File "/usr/lib/python2.7/site-packages/cli/l2tp_cli/l2tp_cli.py", line 433, in show_static_l2tp_session_link
    system_type = l2tpMsg.STATIC_SYSTEM_INFO
AttributeError: 'module' object has no attribute 'STATIC_SYSTEM_INFO'

HA-Shelf-eRPD-0/0# show static l2tp tunnel
2019-01-22 00:28:20,950-cmd_ios.py-1114-ERROR-cli error:'module' object has no attribute 'STATIC_SYSTEM_INFO'
2019-01-22 00:28:20,954-cmd_ios.py-1115-WARNING-Traceback (most recent call last):
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1111, in cmdloop
    stop = self.onecmd(line)
  File "/usr/lib/python2.7/site-packages/cli/cmd_ios/cmd_ios.py", line 1051, in onecmd
    stop = func()
  File "/usr/lib/python2.7/site-packages/cli/l2tp_cli/l2tp_cli.py", line 215, in show_static_l2tp_tunnel
    system_type = l2tpMsg.STATIC_SYSTEM_INFO
AttributeError: 'module' object has no attribute 'STATIC_SYSTEM_INFO'

show tech-support

To display general information about the router when reporting a problem, use the show tech-support command in privileged EXEC mode.

show tech-support

Command Default

None.

Command Modes

Privileged EXEC (#) (FCC and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show tech-support command for all the line cards:

HA-Shelf-FCC# show tech-support
----14:01:22.147 Tue Jan 08 2019: show clock----
14:01:22.149 Tue Jan 08 2019


----14:01:22.149 Tue Jan 08 2019: show version----
Cisco FCC Software, version fcc_V2.1_20190104231640, build by yangluo, on 2019-01-04 15:18:08
Branch information:
FCC branch: hds_dev
OpenRPD branch: rphy_dev

System image file:
Current image is "/bootflash/openwrt-bundle-190104_231125.itb.sign"
Primary image is "/bootflash/openwrt-bundle-190104_231125.itb.sign"
Secondary image is "/bootflash/openwrt-bundle-190104_231125.itb.sign"

System uptime: 12 hours, 56 minutes, 3 seconds

Last reload reason: Reboot

System memory information:
MemTotal:        1861548 kB
MemFree:         1014144 kB
MemAvailable:    1248236 kB
Buffers:            2840 kB
Cached:           302780 kB

For more credits info of HA-Shelf used open source, use "show version credits"



----14:01:22.955 Tue Jan 08 2019: show version all----
FCC:
	Cisco FCC Software, version fcc_V2.1_20190104231640, build by yangluo, on 2019-01-04 15:18:08
	Branch information:
	FCC branch: hds_dev
	OpenRPD branch: rphy_dev
	
	System image file:
	Current image is "/bootflash/openwrt-bundle-190104_231125.itb.sign"
	Primary image is "/bootflash/openwrt-bundle-190104_231125.itb.sign"
	Secondary image is "/bootflash/openwrt-bundle-190104_231125.itb.sign"
	
	System uptime: 12 hours, 56 minutes, 4 seconds
	
	Last reload reason: Reboot
	
	System memory information:
	MemTotal:        1861548 kB
	MemFree:         1013500 kB
	MemAvailable:    1247592 kB
	Buffers:            2840 kB
	Cached:           302784 kB

Linecard slot 0:
	Cisco HDSHELF Software, version hdshelf_V2.1_20190104231640, build by yangluo, on 2019-01-04 15:18:08
	Branch information:
	Linecard branch: hds_dev
	OpenRPD branch: rphy_dev
	
	System image file:
	Current image is from FCC
	Backup image is "/bootflash/openwrt-bundle-190104_231125.itb.sign"
	
	System uptime: 12 hours, 53 minutes, 2 seconds
	
	Last reload reason: Powercycle
	
	System memory information:
	MemTotal:        5913552 kB
	MemFree:         2094440 kB
	MemAvailable:    2305652 kB
	Buffers:           20048 kB
	Cached:           478528 kB

For more credits info of HA-Shelf used open source, use "show version credits"



----14:01:25.053 Tue Jan 08 2019: show running-config----
Building configuration...
!
hostname prefix F02-Shelf 
!
login password 21232f297a57a5a743894a0e4a801fc3 
!
over-temp-shutdown enable 
!
trunk vlan 423 slot 0 erpd 0 
trunk vlan 423 slot 0 erpd 1 
trunk vlan 423 slot 0 erpd 2 
trunk vlan 423 slot 0 erpd 3 
trunk vlan 423 slot 0 erpd 4 
trunk vlan 423 slot 0 erpd 5 
trunk vlan 423 slot 1 erpd 0 
trunk vlan 423 slot 1 erpd 1 
trunk vlan 423 slot 1 erpd 2 
trunk vlan 423 slot 1 erpd 3 
trunk vlan 423 slot 1 erpd 4 
trunk vlan 423 slot 1 erpd 5 
!
mgmt ip 192.0.2.1 netmask 255.255.255.0 gateway 192.0.2.2 
!
bh-erpd-mapping backhaul 0 erpd 0
bh-erpd-mapping backhaul 1 erpd 1
bh-erpd-mapping backhaul 2 erpd 2
bh-erpd-mapping backhaul 3 erpd 3
bh-erpd-mapping backhaul 4 erpd 4
bh-erpd-mapping backhaul 5 erpd 5
!
link-redundancy mode N/A
!


----14:01:25.061 Tue Jan 08 2019: show platform----
Chassis type: HA-RPHY-CHASSIS

Slot       Type                 State          
---------- -------------------- ---------------
  LC0      HA-RPHY-6x12-LC      OK             
  LC1      HA-RPHY-6x12-LC      OK             
  PIC0     HA-RPHY-PIC          OK             
  PIC1     HA-RPHY-PIC          OK             
  PIC2     HA-RPHY-PIC          OK             
  PIC3     HA-RPHY-PIC          OK             
  PIC4     HA-RPHY-PIC          OK             
  PIC5     HA-RPHY-PIC          OK             
  P0       CBR-AC-PS            OK             
  P1       CBR-AC-PS            OK             
  P2       UNKNOWN              N/A            
  P3       UNKNOWN              N/A            
  FAN0     UNKNOWN              NORMAL         
  FAN1     UNKNOWN              NORMAL         
  FAN2     UNKNOWN              NORMAL         
  FAN3     UNKNOWN              NORMAL         
  FAN4     UNKNOWN              NORMAL         


----14:01:26.791 Tue Jan 08 2019: show platform diag----
Chassis type: HA-RPHY-CHASSIS

HA-RPHY-FAN-TRAY:
	State                       : OK
	Software declared up time   : 12 hours, 56 minutes, 8 seconds
	Primary UBoot               : 181019 *
	Golden UBoot                : 180508
	IOFPGA version              : a209 (Primary)
	EOBC version                : 1.01

PIC0, HA-RPHY-PIC:
	State                       : OK

P0, CBR-AC-PS:
	State                       : OK

FAN0, UNKNOWN:
	State                       : NORMAL
	Physical insert detect time : 12 hours, 54 minutes, 10 seconds

LC0, HA-RPHY-6x12-LC:
	State                       : OK
	Software declared up time   : 12 hours, 53 minutes, 7 seconds
	Primary UBoot               : 23 *
	Golden UBoot                : 20
	FPGA version                : 2.3.15
	IOFPGA version              : c129
	ADM1266-0 firmware version  : 010a04
	ADM1266-0 config version    : A14
	ADM1266-1 firmware version  : 010a04
	ADM1266-1 config version    : A14
	ADM1266-2 firmware version  : 010a04
	ADM1266-2 config version    : A14
	JPLD version                : 0x2



----14:01:31.932 Tue Jan 08 2019: show inventory----
NAME: Cisco Smart PHY 7200 HA-Shelf Chassis
PID: HA-RPHY-CHASSIS    SN: FXS2209Q26V      VID: 04

----14:01:33.910 Tue Jan 08 2019: show erpd----
Slot Index IPv4           MAC               Master Online
0    0     ---            BA:DB:AD:17:0C:20        N
0    1     ---            BA:DB:AD:17:0C:21        N
0    2     ---            BA:DB:AD:17:0C:22        N
0    3     ---            BA:DB:AD:17:0C:23        N


----14:01:34.003 Tue Jan 08 2019: show redundancy----
Redundant System Information :
------------------------------
       Available system uptime = 1 day, 35 minutes
Switchovers system experienced = 0
              Standby failures = 0
       Last switchover reason = none


----14:01:34.005 Tue Jan 08 2019: show trunk vlan----
Slot  eRPD  VLAN
0     0     423 
0     1     423  

----14:01:34.058 Tue Jan 08 2019: show bh-erpd-mapping all----
LC 0 :
backhaul0 <---> erpd0
backhaul1 <---> erpd1
backhaul2 <---> erpd2
backhaul3 <---> erpd3
backhaul4 <---> erpd4
backhaul5 <---> erpd5

LC 2 is not up.

LC 12 is not up.

----14:01:34.161 Tue Jan 08 2019: show link-redundancy all----
LC 0 :
---------------------------
Backhaul |State   Role
---------|-----------------
0        |Active  Primary
1        |Active  Primary
2        |Active  Primary
3        |Active  Primary
4        |Active  Primary
5        |Active  Primary
6        |  -     Primary
7        |  -     Primary
---------------------------

LC 2 is not up.

LC 12 is not up.

----14:01:34.259 Tue Jan 08 2019: show group environment all----
Sensor List:  Environmental Monitoring
ID    Sensor                  State                Value
--    ------                  -----                -----
1     temp: Fan0 Inlet        NORMAL               35 Celsius
2     temp: Fan1 Inlet        NORMAL               32 Celsius
3     temp: Fan2 Inlet        NORMAL               33 Celsius
4     temp: Fan3 Inlet        NORMAL               32 Celsius
5     temp: Fan4 Inlet        NORMAL               28 Celsius
6     temp: PIC0 Exhaust Air1 NORMAL               28 Celsius
7     temp: PIC0 Exhaust Air2 NORMAL               27 Celsius
8     temp: PIC1 Exhaust Air1 NORMAL               28 Celsius

FCC module List:  Environmental Monitoring
Device name    State    PWM setpoint for fans   RPD inlet sensor reading used 
-----------    -----    ---------------------   ----------------------------- 
FCC module     NORMAL   7000 RPM                31 Celsius                    

Fan module List:  Environmental Monitoring
ID    Fan module  State       Temperature     Speed     
--    ----------  -----       -----------     -----     
1     Fan 0       NORMAL      35 Celsius      6854 RPM  
2     Fan 1       NORMAL      32 Celsius      6823 RPM  
3     Fan 2       NORMAL      33 Celsius      6873 RPM  
4     Fan 3       NORMAL      32 Celsius      6841 RPM  
5     Fan 4       NORMAL      28 Celsius      6820 RPM  

====================================
Slot      Controller          Value
------------------------------------
 P0        PEM Power           267 W
 P1        PEM Power           249 W
------------------------------------
Input Power Summary:     516 W
====================================
 LC0       FRU Power         136 W
 LC1       FRU Power         131 W
------------------------------------
Power Consumed Summary:    267 W
====================================
More Cards can be supported:   
------------------------------------
LC:                         11
====================================


----14:01:36.367 Tue Jan 08 2019: show cpu all----
Slot  CPU%
0     30        
1     37        
FCC   0         


----14:01:37.741 Tue Jan 08 2019: show memory all----
Slot  MemoryUsed  MemoryFree
0     3742896K    2170656K
1     3926620K    1986932K
FCC   866025K     1040199K

show tgc-clock

To view the sync state of the PTP clock, use the show tgc-clock command in privileged EXEC mode.

show tgc-clock erpd state

Command Default

None.

Command Modes

Privileged EXEC (#) (Line Card, Primary eRPD, and Non-Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show tgc-clock command for all the line cards:

HA-Shelf-eRPD-0/0# show tgc-clock 5 state
clock state       : SUB_SYNC
current tod       : 1546940711  Tue Jan  8 09:45:11 2019
  SCQAM0: 0x10a9c996
  SCQAM1: 0x10a9d72e
US Port 0:
  TOP: 0x10a9e32e, RCVR0: 0x10aa0c80, DELTA: 0x2952
  TOP: 0x10aa2d52, RCVR1: 0x10aa4780, DELTA: 0x1a2e
  TOP: 0x10aa6582, RCVR2: 0x5b58000, DELTA: 0xf50b1a7e
  TOP: 0x10aaa5be, RCVR3: 0x5b5c000, DELTA: 0xf50b1a42
  TOP: 0x10aadc91, RCVR4: 0x5b5a000, DELTA: 0xf50ac36f
  TOP: 0x10ab103b, RCVR5: 0x5b5c000, DELTA: 0xf50aafc5
  TOP: 0x10ab4a96, RCVR6: 0x5b5c000, DELTA: 0xf50a756a
  TOP: 0x10ab7c85, RCVR7: 0x5b5e000, DELTA: 0xf50a637b
  TOP: 0x10abc1e4, RCVR8: 0x5b60000, DELTA: 0xf50a3e1c
  TOP: 0x10ac12f7, RCVR9: 0x10ac3e00, DELTA: 0x2b09
  TOP: 0x10ac5945, RCVR10: 0x5b62000, DELTA: 0xf509c6bb
  TOP: 0x10ac9a3f, RCVR11: 0x5b66000, DELTA: 0xf509c5c1
US Port 1:
  TOP: 0x10acdaea, RCVR0: 0x5b44000, DELTA: 0xf5076516
  TOP: 0x10ad1b95, RCVR1: 0x5b4c000, DELTA: 0xf507a46b
  TOP: 0x10adb626, RCVR2: 0x5b4e000, DELTA: 0xf50729da
  TOP: 0x10ae3980, RCVR3: 0x5b62000, DELTA: 0xf507e680
  TOP: 0x10af5161, RCVR4: 0x5b62000, DELTA: 0xf506ce9f
  TOP: 0x10af9bc5, RCVR5: 0x5b64000, DELTA: 0xf506a43b
  TOP: 0x10afd414, RCVR6: 0x5b64000, DELTA: 0xf5066bec
  TOP: 0x10b00fcb, RCVR7: 0x5b68000, DELTA: 0xf5067035
  TOP: 0x10b053ae, RCVR8: 0x5b68000, DELTA: 0xf5062c52
  TOP: 0x10b097c1, RCVR9: 0x5b6a000, DELTA: 0xf506083f
  TOP: 0x10b0cd66, RCVR10: 0x5b6a000, DELTA: 0xf505d29a
  TOP: 0x10b0fdd9, RCVR11: 0x5b6c000, DELTA: 0xf505c227

show tod

To display the date and time of the day, use the show tod command.

show tod

Command Default

None.

Command Modes

Privileged EXEC (#) (Non-Primary eRPD and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

The following is a sample output of the show tod command:

HA-Shelf-eRPD-0/0# show tod
Server       TimeOffset  Time                  Status  
10.79.41.66  32400       2019 Jan 22 00:25:36  OK

show trunk vlan

To view virtual LAN configuration on your Remote PHY Shelf 7200 device, use the show trunk vlan command in privileged EXEC mode.

show trunk vlan

Command Default

None.

Command Modes

Privileged EXEC (#) (FCC, Line Card, and Primary eRPD)

Command History


Release	Modification
Cisco Remote PHY Shelf 7200 Software 1.1	This command was introduced on the Cisco Remote PHY Shelf 7200.

Examples

This is a sample output of the show trunk vlan command:

HA-Shelf-FCC# show trunk vlan
Slot  eRPD  VLAN
0     0     423 
0     1     423 
0     2     423 
0     3     423 
0     4     423 
0     5     423 
1     0     423 
1     1     423 
1     2     423 
1     3     423 
1     4     423 
1     5     423

Bias-Free Language

Results

Chapter: Commands: show o through show t

Commands: show o through show t

show platform diag

Command Default

Command Modes

Command History

Examples

show pm

Syntax Description

Command Default

Command Modes

Command History

Examples

show process

Command Default

Command Modes

Command History

Examples

show provision

Syntax Description

Command Default

Command Modes

Command History

Examples

show ptp clock

Command Default

Command Modes

Command History

Examples

show reboot hold

Command Default

Command Modes

Command History

Examples

show running-config

Syntax Description

Command Default

Command Modes

Command History

Examples

show sfp info

Syntax Description

Command Default

Command Modes

Command History

Examples

show ssh

Command Default

Command Modes

Command History

Examples

show startup-config

Command Default

Command Modes

Command History

Examples

show static l2tp

Syntax Description

Command Default

Command Modes

Command History

Examples

show tech-support

Command Default

Command Modes

Command History

Examples

show tgc-clock

Command Default

Command Modes

Command History

Examples

show tod

Command Default

Command Modes

Command History

Examples