Configure Port Forwarding and Port Triggering in RV160 and RV260 Routers

Available Languages

Download Options

PDF (558.7 KB)
View with Adobe Reader on a variety of devices
ePub (531.7 KB)
View in various apps on iPhone, iPad, Android, Sony Reader, or Windows Phone
Mobi (Kindle) (648.0 KB)
View on Kindle device or Kindle app on multiple devices

Updated:February 21, 2020

Document ID:1582314584857268

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Objective
Applicable Devices | Firmware Version
Introduction
Configure Port Forwarding
Configure Port Triggering

Objective

The objective of this article is to show you how to configure port forwarding and port triggering on the RV160 and RV260 Routers.

Applicable Devices | Firmware Version

RV160 | 1.0.00.13
RV260 | 1.0.00.13

Introduction

Port forwarding and port triggering are features that allow some internet users to have access to specific resources on your network, while protecting the resources that you want to keep private.

Port forwarding allows public access to services on network devices on the Local Area Network (LAN) by opening a specific port or port range for a service, such as file transfer protocol (FTP). Port forwarding opens a port range for services such as internet gaming that uses alternate ports to communicate between the server and the LAN host.

Port triggering allows a specified port or port range to open for inbound traffic after user sends outbound traffic through the trigger port. Port triggering allows the device to monitor outgoing data for specific port numbers. The device recalls the IP address of the client that sent the matching data. When the requested data returns through the device, the data is sent to the proper client using the IP addressing and port mapping rules.

For more information on port forwarding and port triggering, click here.

Configure Port Forwarding

To configure port forwarding, follow these steps:

Step 1. Log in to the web configuration utility. Enter the username and password for the router and click Login. The default username and password is cisco.

In this article, we will be using the RV260 to configure port forwarding. The configuration may vary depending on the model you use.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position PF-PT Step1.png$

Step 2. Click Firewall > Port Forwarding.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PF_Step2.png$

Step 3. In the Port Forwarding Table, click add icon or select the row and click edit icon) and configure the following:

Enable	Check Enable to enable port forwarding
External Service	Select an external service from the drop-down list. (If a service is not listed, you can add or modify the list by following the instructions in the Service Management section)
Internal Service	Select an internal service from the drop-down list. (If a service is not listed, you can add or modify the list by following the instructions in the Service Management section)
Internal IP Addresses	Enter the internal IP addresses of the server
Interfaces	Select the interface from the drop-down list, to apply port forwarding on

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PF_Step3.png$

To add or edit an entry on the Service list, follow these steps:

Step 4. Click Service Management.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PF_Step4.png$

Step 5. In the Service Management click Add icon or select a row and click Edit icon.

Configure the following:

Application Name - Name of the service or application.
Protocol - Required protocol. Refer to the documentation for the service that you are hosting.
Port Start/ICMP Type/IP Protocol - Range of port numbers reserved for this service.
Port End - Last number of the port reserved for this service.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PF_Step5.png$

To add a service, click on the plus icon and configure Name, Protocol, Port Start/ICMP Type/IP Protocol and Port End/ICMP Code.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Add step.png$

To edit a service, select a row and click on the edit icon to configure the fields as shown below.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Edit step.png$

In this example, FTP service is selected.

Step 6. Click Apply.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PF_Step6.png$

Step 7. In the Universal Plug and Play (UPnP) Port Forwarding Table, click the refresh icon to refresh the data. The port forwarding rules for UPnP are dynamically added by the UPnP application.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PF_Step7.png$

Configure Port Triggering

To configure port triggering, follow these steps:

Step 1. Log in to the web configuration utility. Enter the username and password for the router and click Login. The default username and password is cisco.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position PF-PT Step1.png$

In this article, we will be using the RV260 to configure port triggering. The configuration may vary depending on the model you use.

Step 2. Click Firewall > Port Triggering.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PT_Step2.png$

Step 3. To add or edit a service to the port triggering table, configure the following:

Click add icon (or select the row and click edit icon and enter the information:

Enable	Check to enable port triggering
Application Name	Enter the name of the application
Trigger Service	Select a service from the drop-down list (If a service is not listed, you can add or modify the list by following the instructions in the Service Management section)
Incoming Service	Select a service from the drop-down list (If a service is not listed, you can add or modify the list by following the instructions in the Service Management section)
Interfaces	Select the interface from the drop-down list

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PT_Step3.png$

Step 4. Click Service Management to add, or edit an entry on the Service list.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PT_Step4.png$

Step 5. In the Service Management, click add icon or select the row and click edit icon.

Configure the following:

Application Name - Name of the service or application.
Protocol - Required protocol. Refer to the documentation for the service that you are hosting.
Port Start/ICMP Type/IP Protocol - Range of port numbers reserved for this service.
Port End - Last number of the port reserved for this service.

$C:\Users\kriselva\Desktop\Pole Position\PF-PT\Pole position_PT_Step5.png$