Implementing LTE WAN Backup with Cisco RV34x Series Routers Using a Windows PC

Available Languages

Download Options

PDF (1.5 MB)
View with Adobe Reader on a variety of devices
ePub (1.3 MB)
View in various apps on iPhone, iPad, Android, Sony Reader, or Windows Phone
Mobi (Kindle) (1.4 MB)
View on Kindle device or Kindle app on multiple devices

Updated:February 6, 2020

Document ID:1581028955961308

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Objective

This article explains how to use a Cisco Business RV router in tandem with a third-party router that has integrated Long Term Evolution (LTE) Wide Area Network (WAN) capability. The LTE router is used as back up connectivity to the Internet for the RV34x series router. In this scenario, the NETGEAR Nighthawk LTE Mobile Hotspot Router, Model MR1100, will be used.

If you use a Mac computer, you should follow the steps in Implementing LTE WAN Backup with Cisco RV34x Series Routers Using a Mac OSX.

NETGEAR Resources
Backup Internet Topology
Overview for Set Up
Initial Configuration on the LTE Mobile Router
Configure IP Passthrough on the LTE Mobile Router
Configure RV34x Router for Backup Internet on WAN 2
Verify Internet Access on the Cisco RV34x Router
Verify the WAN 2 Backup Internet

Applicable Devices | Firmware Version

RV340 | Firmware 1.0.03.16
RV340W | Firmware 1.0.03.16
RV345 | Firmware 1.0.03.16
RV345P | Firmware 1.0.03.16

Introduction

It is essential for a business to have consistent Internet. You want to do everything you can to ensure connectivity in your network, but you have no control over the reliability of your Internet Service Provider (ISP). At some point their service might go down, which means your network would too. That’s why it is important to plan ahead. What can you do?

It’s simple, with the Cisco Business RV34x series routers. There are two options available to set up a backup Internet:

You can add a second traditional ISP using a 3G/4G LTE Universal Serial Bus (USB) compatible dongle with a subscription. The challenge of this setup is when a third-party does an update to the dongle software, it can sometimes cause compatibility issues. If you would like to see the most up to date ISP USB dongle compatibility with Cisco RV Series Routers, click here.
Utilize the 2^nd WAN port and add a second ISP router with integrated LTE capability. The focus of this article is on this option, so if that interests you, please continue!

In this scenario we will focus on adding an ISP router with LTE capability, specifically, the NETGEAR Nighthawk LTE Mobile Hotspot Router, Model MR1100. The router uses mobile data, just like a mobile phone, when it is used to access the Internet so make sure you have the appropriate plan to support your environment.

Fourth generation (4G) LTE is an improvement over 3G. It provides a more reliable connection, faster upload and download speeds, and better voice and video clarity. Although 4G LTE is not a full 4G connection, it is considered far superior to 3G.

In addition, the secondary ISP can be configured to load balance and expand bandwidth on your network. If you would like to view a video on this, check out Cisco Tech Talk: Configuring Dual WAN for Load Balancing on RV340 Series Routers.

Cisco Business does not sell or support NETGEAR products. It was simply used as an LTE router that was compatible with the Cisco RV series routers.

NETGEAR Resources

Product Page
Quick Start Guide
User Manual
What Cellular Bands are Supported by MR1100 Nighthawk M1 Mobile Router?
List of Carriers Supported by AirCard Hotspot
Purchase the MR1100 Nighthawk M1 Mobile Router (Check your ISP for availability)

Backup Internet Topology

The image below illustrates the Primary ISP connected to WAN1 on the RV Series Router (represented as a blue box) and WAN 2 connected to the shown port on the NETGEAR router (the black piece of equipment) for the secondary ISP.

Before connecting the LTE router into the RV340 router, follow the instructions below to set up the LTE router as a backup Internet.

Overview for Set Up

Here are the high-level steps needed to enable backup Internet.

Initial Configuration on the LTE Mobile Router
Configure IP Passthrough on the LTE Mobile Router
Configure the RV34x Router for Backup Internet on WAN 2

Initial Configuration on the LTE Mobile Router

Use a workstation to connect to the Nighthawk LTE router and follow the instructions to set up standard administration and hotspot networks. Steps can be found in the NETGEAR User Manual. This sets the LTE router as a Wi-Fi hotspot.

Initial configuration for the LTE mobile router allows an Ethernet tethered connection. Using the same workstation, connect to the Ethernet port and verify a valid IP address is issued from the LTE mobile router. Check by opening your browser to check a valid Internet site.

The hotspot will be disabled automatically in the next section. This will allow access to the external public-facing IP address required for our needs.

Configure IP Passthrough on the LTE Mobile Router

After following the steps in the section above, you may access the dashboard to configure the LTE mobile router as a standalone device for straight access into the public Internet.

Complete the IP Passthrough configuration options to provide a direct, public-facing IP address.

Step 1

In a web browser, enter attwifimanager/index.html.

The dashboard is available after you go through the conventional setup instructions, so you should see a screen similar to the one shown below.

Step 2

Click Settings to access the advanced configuration parameters.

Step 3

Navigate to Mobile Router Setup.

Step 4

Under IP PASSTHROUGH, select ON Disables Wi-Fi on the mobile router. This will disable Wi-Fi hotspot support.

Step 5

Under TETHERING, select Charge only from the drop-down menu.

Step 6

Click Apply.

Step 7

A pop-up window will open to Confirm Restart, click Continue.

Step 8

A notice will appear in the upper right corner of the screen, Mobile Broadband Disconnected.

Step 9

A notice will appear, SCANNING FOR MOBILE ROUTER.

Step 10

The Wi-Fi interface needs to be disabled to test the configuration of the LTE router on the LAN network. To disable the Wi-Fi connection, click the Wi-Fi icon in the lower right-hand corner of your computer screen.

Step 11

Click on the connected Wi-Fi button to shut the Wi-Fi off.

Step 12

You will see that the Wi-Fi for the RV340 router is turned off.

Step 13

In Step 7, you had the NETGEAR router perform a reboot. Once that is complete, take an Ethernet cable and connect the LTE router directly to your personal computer.

Step 14

Right-click on the computer icon with the exclamation point.

Step 15

Select Open Network & Internet settings.

Step 16

Scroll down. Note the ISP Internet-facing IP address of your Ethernet LAN. This is the IP address of the LTE router.

Step 17

Check connectivity to the Internet by opening your browser and entering a valid Internet site.

Step 18

Disconnect the Ethernet cable from the LTE router and PC.

Configure RV34x Router for Backup Internet on WAN 2

Now that the LTE router has been configured and the workstation is receiving an ISP-generated IP address, connect the LTE mobile router directly to WAN 2 port of the RV340 series router as shown in the Backup Internet Topology section of this article. This address was provided to the Cisco router directly by the LTE router (from the ISP).

Currently the Internet connection is provided by WAN 1 of the RV340.