This doucment describes a troubleshooting scenario which applies to applications that do not work through the Cisco AnyConnect VPN Client.
There are no specific requirements for this document.
The information in this document is based on a Cisco Adaptive Security Appliance (ASA) that runs Version 8.x.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
This typical troubleshooting scenario applies to applications that do not work through the Cisco AnyConnect VPN Client for end-users with Microsoft Windows-based computers. These sections address and provide solutions to the problems:
If you see errors in the setupapi log file, you can turn up verbosity to 0x2000FFFF as described in this Windows KB article . Notice the article tells you to set it to 0xFFFF, but if you add the high-order value of 0x2, it makes the logging faster.
Obtain the MSI installer log file:
If this is an initial web deploy install, this log is located in the per-user temp directory.
Windows XP / Windows 2000:
\Documents and Settings\<username>\Local Settings\Temp\
If this is an automatic upgrade, this log is in the temp directory of the system:
The filename is in this format: anyconnect-win-x.x.xxxx-k9-install-yyyyyyyyyyyyyy.log. Obtain the most recent file for the version of the client you want to install. The x.xxxx changes based on the version, such as 2.0.0343, and yyyyyyyyyyyyyy is the date and time of the install.
Obtain the PC system information file:
From a Command Prompt/DOS box, type this:
Windows XP / Windows 2000:
winmsd /nfo c:\msinfo.nfo
msinfo32 /nfo c:\msinfo.nfo
Note: After you type into this prompt, wait. It can take between two to five minutes for the file to complete.
Obtain a systeminfo file dump from a Command Prompt:
Disconnection or Inability to Establish Initial Connection
If you experience connection problems with the AnyConnect client, such as disconnections or the inability to establish an initial connection, obtain these files:
The configuration file from the ASA in order to determine if anything in the configuration causes the connection failure:
From the console of the ASA, type write net x.x.x.x:ASA-Config.txt where x.x.x.x is the IP address of a TFTP server on the network.
From the console of the ASA, type show running-config. Let the configuration complete on the screen, then cut-and-paste to a text editor and save.
The ASA event logs:
In order to enable logging on the ASA for auth, WebVPN, Secure Sockets Layer (SSL), and SSL VPN Client (SVC) events, issue these CLI commands:
config terminal logging enable logging timestamp logging class auth console debugging logging class webvpn console debugging logging class ssl console debugging logging class svc console debugging
Originate an AnyConnect session and ensure that the failure can be reproduced. Capture the logging output from the console to a text editor and save.
In order to disable logging, issue no logging enable.
The Cisco AnyConnect VPN Client log from the Windows Event Viewer of the client PC:
Choose Start > Run.
Right-click the Cisco AnyConnect VPN Client log, and select Save Log File as AnyConnect.evt.
Note: Always save it as the .evt file format.
If the user cannot connect with the AnyConnect VPN Client, the issue might be related to an established Remote Desktop Protocol (RDP) session or Fast User Switching enabled on the client PC. The user can see the AnyConnect profile settings mandate a single local user, but multiple local users are currently logged into your computer. A VPN connection will not be established error message error on the client PC. In order to resolve this issue, disconnect any established RDP sessions and disable Fast User Switching.
Note: Make sure that port 443 is not blocked so the AnyConnect client can connect to the ASA.
When a user cannot connect the AnyConnect VPN Client to the ASA, the issue might be caused by an incompatibility between the AnyConnect client version and the ASA software image version. In this case, the user receives this error message: The installer was not able to start the Cisco VPN client, clientless access is not available.
When a user cannot connect to the AnyConnect VPN Client from the PC, the issue can be caused by the Antivirus software present on the PC.
Note: AnyConnect must be installed on the computer before you install any third-party firewall/anti-virus (AV) software. If AnyConnect is installed after any third-party firewall/anti-virus software, then AnyConnect fails to connect. In order to resolve this issue, disable all of the features of the personal firewall/AV. Then, make a small change on the AnyConnect virtual adapter and try to reconnect AnyConnect. For more information, refer to Cisco bug IDs CSCsj91840 and CSCti16453.
When you log in the first time to the AnyConnect, the login script does not run. If you disconnect and log in again, then the login script runs fine. This is the expected behavior.
When you connect the AnyConnect VPN Client to the ASA, you might receive this error: User not authorized for AnyConnect Client access, contact your administrator.
This error is seen when the AnyConnect image is missing from the ASA. Once the image is loaded to the ASA, AnyConnect can connect without any issues to the ASA.
This error can be resolved by disabling Datagram Transport Layer Security (DTLS). Go to Configuration > Remote Access VPN > Network (Client) Access > AnyConnect Connection Profiles and uncheck the Enable DTLS check box. This disables DTLS.
The dartbundle files show this error message when the user gets disconnected: TUNNELPROTOCOLDPDMGR_ERROR_NO_DPD_RESPONSE:The secure gateway failed to respond to Dead Peer Detection packets. This error means that the DTLS channel was torn due to Dead Peer Detection (DPD) failure. This error is resolved if you tweak the DPD keepalives and issue these commands:
When problems are detected with passing traffic to the private network with an AnyConnect session through the ASA, complete these data-gathering steps:
Obtain the output of the show vpn-sessiondb detail svc filter name <username> ASA command from the console. If the output shows Filter Name: XXXXX, then gather the output for show access-list XXXXX. Verify that the access-list XXXXX does not block the intended traffic flow.
Export the AnyConnect statistics from AnyConnect VPN Client > Statistics > Details > Export (AnyConnect-ExportedStats.txt).
Check the ASA configuration file for nat statements. If Network Address Translation (NAT) is enabled, these must exempt data that returns to the client as a result of NAT. For example, to NAT exempt (nat 0) the IP addresses from the AnyConnect pool, use this on the CLI:
access-list in_nat0_out extended permit ip any 10.136.246.0 255.255.255.0 ip local pool IPPool1 10.136.246.1-10.136.246.254 mask 255.252.0.0 nat (inside) 0 access-list in_nat0_out
Determine if the tunneled default gateway needs to be enabled for the setup. The traditional default gateway is the gateway of last resort for non-decrypted traffic.
!--- Route outside 0 0 is an incorrect statement. route outside 0 0 10.145.50.1 route inside 0 0 10.0.4.2 tunneled
For example, if the VPN Client needs to access a resource which is not in the routing table of the VPN Gateway, the packet is routed through the standard default gateway. The VPN gateway does not need the complete internal routing table in order to resolve this. The tunneled keyword can be used in this instance.
Verify if the AnyConnect traffic is dropped by the inspection policy of the ASA. You could exempt the specific application that is used by AnyConnct client if you implement the Modular Policy Framework of Cisco ASA. For example, you could exempt the skinny protocol from exemption with these commands.
ASA(config)# policy-map global_policy ASA(config-pmap)# class inspection_default ASA(config-pmap-c)# no inspect skinny
AnyConnect Crash Issues
Complete these data-gathering steps:
Ensure that the Microsoft Utility Dr Watson is enabled. In order to do this, choose Start > Run, and run Drwtsn32.exe. Configure this and click OK:
Number of Instructions : 25 Number of Errors To Save : 25 Crash Dump Type : Mini Dump Symbol Table : Checked Dump All Thread Contexts : Checked Append To Existing Log File : Checked Visual Notification : Checked Create Crash Dump File : Checked
When the crash occurs, gather the .log and .dmp files from C:\Documents and Settings\All Users\Application Data\Microsoft\Dr Watson. If these files appear to be in use, then use ntbackup.exe.
Obtain the Cisco AnyConnect VPN Client log from the Windows Event Viewer of the client PC:
Choose Start > Run.
Right-click the Cisco AnyConnect VPN Client log, and select Save Log File As AnyConnect.evt.
Note: Always save it as the .evt file format.
Fragmentation / Passing Traffic Issues
Some applications, such as Microsoft Outlook, do not work. However, the tunnel is able to pass other traffic such as small pings.
This can provide clues as to a fragmentation issue in the network. Consumer routers are particularly poor at packet fragmentation and reassembly.
Try a scaling set of pings in order to determine if it fails at a certain size. For example, ping -l 500, ping -l 1000, ping -l 1500, ping -l 2000.
It is recommended that you configure a special group for users that experience fragmentation, and set the SVC Maximum Transition Unit (MTU) for this group to 1200. This allows you to remediate users who experience this issue, but not impact the broader user base.
TCP connections hang once connected with AnyConnect.
In order to verify if your user has a fragmentation issue, adjust the MTU for AnyConnect clients on the ASA.
ASA(config)#group-policy <name> attributes webvpn svc mtu 1200
The AnyConnect VPN Client uninstalls itself once the connection terminates. The client logs show that keep installed is set to disabled.
AnyConnect uninstalls itself despite that the keep installed option is selected on the Adaptive Security Device Manager (ASDM). In order to resolve this issue, configure the svc keep-installer installed command under group-policy.
Issue Populating the Cluster FQDN
Problem: AnyConnect client is pre-populated with the hostname instead of the cluster Fully Qualified Domain Name (FQDN).
When you have a load-balancing cluster set up for SSL VPN and the client attempts to connect to the cluster, the request is redirected to the node ASA and the client logs in successfully. After some time, when the client tries to connect to the cluster again, the cluster FQDN is not seen in the Connect to entries. Instead, the node ASA entry to which the client has been redirected is seen.
This occurs because the AnyConnect client retains the host name to which it last connected. This behavior is observed and a bug has been filed. For complete details about the bug, refer to Cisco bug ID CSCsz39019. The suggested workaround is to upgrade the Cisco AnyConnect to Version 2.5.
Backup Server List Configuration
A backup server list is configured in case the main server selected by the user is not reachable. This is defined in the Backup Server pane in the AnyConnect profile. Complete these steps:
Click Manage from the Default Group Policy section.
Select your group-policy and click Edit.
Select Advanced and then click SSL VPN Client.
Click New. Then, you need to type a name for the Profile and assign the XML file.
Connect the client to the session in order to download the XML file.
AnyConnect: Corrupt Driver Database Issue
This entry in the SetupAPI.log file suggests that the catalog system is corrupt:
W239 driver signing class list "C:\WINDOWS\INF\certclas.inf" was missing or invalid. Error 0xfffffde5: Unknown Error., assuming all device classes are subject to driver signing policy.
You can also receive this error message: Error(3/17): Unable to start VA, setup shared queue, or VA gave up shared queue.
You can receive this log on the client: "The VPN client driver has encountered an error".
This issue is due to Cisco bug ID CSCsm54689. In order to resolve this issue, make sure that Routing and Remote Access Service is disabled before you start AnyConnect. If this does not resolve the issue, complete these steps:
Open a command prompt as an Administrator on the PC (elevated prompt on Vista).
Error: Unable to Update the Session Management Database
While the SSL VPN is connected through a web browser, the Unable to Update the Session Management Database. error message appears, and the ASA logs show %ASA-3-211001: Memory allocation Error. The adaptive security appliance failed to allocate RAM system memory.
This issue is due to Cisco bug ID CSCsm51093. In order to resolve this issue, reload the ASA or upgrade the ASA software to the interim release mentioned in the bug. Refer to Cisco bug ID CSCsm51093 for more information.
This issue can also be resolved if you disable threat-detection on ASA if threat-detection is used.
Error: "Module c:\Program Files\Cisco\Cisco AnyConnect VPN Client\vpnapi.dll failed to register"
When you use the AnyConnect client on laptops or PCs, an error occurs during the install:
"Module C:\Program Files\Cisco\Cisco AnyConnect VPN Client\vpnapi.dll failed to register..."
When this error is encountered, the installer cannot move forward and the client is removed.
These are the possible workarounds to resolve this error:
Copy these files from the \ProgramFiles\Cisco\CiscoAnyconnect folder to a new folder and run the regsvr32 vpnapi.dll command prompt:
Reimage the operating system on the laptop/PC.
The log message related to this error on the AnyConnect client looks similar to this:
DEBUG: Error 2911: Could not remove the folderC:\Program Files\Cisco\Cisco AnyConnect VPN Client\. The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2911. The arguments are: C:\Program Files\Cisco\Cisco AnyConnect VPN Client\, , DEBUG: Error 2911: Could not remove the folder C:\Program Files\Cisco\Cisco AnyConnect VPN Client\. The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2911. The arguments are: C:\Program Files\Cisco\Cisco AnyConnect VPN Client\, , Info 1721. There is a problem with this Windows Installer package. A program required for this install to complete could not be run. Contact your support personnel or package vendor. Action: InstallHelper.exe, location: C:\Program Files\Cisco\Cisco AnyConnect VPN Client\InstallHelper.exe, command: -acl "C:\Documents and Settings\All Users\Application Data\Cisco\Cisco AnyConnect VPN Client\\" -r
Error: "An error was received from the secure gateway in response to the VPN negotiation request. Please contact your network administrator"
When clients try to connect to the VPN with the Cisco AnyConnect VPN Client, this error is received.
This message was received from the secure gateway:
"Illegal address class" or "Host or network is 0" or "Other error"
The issue occurs because of the ASA local IP pool depletion. As the VPN pool resource is exhausted, the IP pool range must be enlarged.
Cisco bug ID is CSCsl82188 is filed for this issue. This error usually occurs when the local pool for address assignment is exhausted, or if a 32-bit subnet mask is used for the address pool. The workaround is to expand the address pool and use a 24-bit subnet mask for the pool.
Error: Session could not be established. Session limit of 2 reached.
When you try to connect more than two clients with the AnyConnect VPN Client, you receive the Login Failed error message on the Client and a warning message in the ASA logs that states Session could not be established. Session limit of 2 reached. I have the AnyConnect essential license on the ASA, which runs Version 8.0.4.
This error occurs because the AnyConnect essential license is not supported by ASA version 8.0.4. You need to upgrade the ASA to version 8.2.2. This resolves the error.
Note: Regardless of the license used, if the session limit is reached, the user will receive the login failed error message.
This error can also occur if the vpn-sessiondb max-anyconnect-premium-or-essentials-limit session-limit command is used to set the limit of VPN sessions permitted to be established. If the session-limit is set as two, then the user cannot establish more than two sessions even though the license installed supports more sessions. Set the session-limit to the number of VPN sessions required in order to avoid this error message.
Error: Anyconnect not enabled on VPN server while trying to connect anyconnect to ASA
You receive the Anyconnect not enabled on VPN server error message when you try to connect AnyConnect to the ASA.
This error is resolved if you enable AnyConnect on the outside interface of the ASA with ASDM. For more information on how to enable AnyConnect on the outside interface, refer to Enabling the SSL VPN Client Protocol.
Error:- %ASA-6-722036: Group client-group User xxxx IP x.x.x.x Transmitting large packet 1220 (threshold 1206)
The %ASA-6-722036: Group < client-group > User < xxxx > IP < x.x.x.x> Transmitting large packet 1220 (threshold 1206) error message appears in the logs of the ASA. What does this log mean and how is this resolved?
This log message states that a large packet was sent to the client. The source of the packet is not aware of the MTU of the client. This can also be due to compression of non-compressible data. The workaround is to turn off the SVC compression with the svc compression none command. This resolves the issue.
Error: The secure gateway has rejected the agent's vpn connect or reconnect request.
When you connect to the AnyConnect Client, this error is received: "The secure gateway has rejected the agent's vpn connect or reconnect request. A new connection requires re-authentication and must be started manually. Please contact your network administrator if this problem persists. The following message was received from the secure gateway: no assigned address".
This error is also received when you connect to the AnyConnect Client: "The secure gateway has rejected the connection attempt. A new connection attempt to the same or another secure gateway is needed, which requires re-authentication. The following message was received from the secure gateway:Host or network is 0".
This error is also received when you connect to the AnyConnect Client: "The secure gateway has rejected the agent's vpn connect or reconnect request. A new connection requires a re-authentication and must be started manually. Please contact the network administrator if the problem persists. The following message was received from the secure gateway: No License".
The router was missing pool configuration after reload. You need to add the concerned configuration back to the router.
Router#show run | in pool
ip local pool SSLPOOL 192.168.30.2 192.168.30.254 svc address-pool SSLPOO
The "The secure gateway has rejected the agent's vpn connect or reconnect request. A new connection requires a re-authentication and must be started manually. Please contact the network administrator if the problem persists. The following message was received from the secure gateway: No License" error occurs when the AnyConnect mobility license is missing. Once the license is installed, the issue is resolved.
Error: "Unable to update the session management database"
When you try to authenticate in WebPortal, this error message is received: "Unable to update the session management database".
This problem is related to memory allocation on the ASA. This issue is mostly encountered when the ASA Version is 8.2.1. Originally, this requires a 512MB RAM for its complete functionality. Refer to the Memory requirements section in the release notes.
As a temporary workaround, try to free the memory with these steps:
Disable the threat-detection.
Disable SVC compression.
Reload the ASA.
Error: "The VPN client driver has encountered an error"
This is an error message obtained on the client machine when you try to connect to AnyConnect.
In order to resolve this error, complete this procedure in order to manually set the AnyConnect VPN agent to Interactive:
Right-click My Computer > Manage > Services and Applications > Services > and select the Cisco AnyConnect VPN Agent.
Right-click Properties, then log on, and select Allow service to interact with the desktop.
This sets the registry Type value DWORD to 110 (default is 010) for the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\vpnagent.
Note: If this is to be used, then the preference would be to use the .MST transform in this instance. This is because if you set this manually with these methods, it requires that this be set after every install/upgrade process. This is why there is a need to identify the application that causes this problem.
When Routing and Remote Access Service (RRAS) is enabled on the Windows PC, AnyConnect fails with the The VPN client driver has encountered an error. error message. In order to resolve this issue, make sure that Routing and RRAS is disabled before starting AnyConnect. Refer to Cisco bug ID CSCsm54689 for more information.
Error: "Unable to process response from xxx.xxx.xxx.xxx"
AnyConnect clients fail to connect to a Cisco ASA. The error in the AnyConnect window is "Unable to process response from xxx.xxx.xxx.xxx".
In order to resolve this error, try these workarounds:
Remove WebVPN from the ASA and reenable it.
Change the port number to 444 from the existing 443 and reenable it on 443.
For more information on how to enable WebVPN and change the port for WebVPN, refer to this Solution.
Error: "The AnyConnect package on the secure gateway could not be located"
This error is caused on the user's Linux machine when it tries to connect to the ASA by launching AnyConnect. Here is the complete error:
"The AnyConnect package on the secure gateway could not be located. You may be experiencing network connectivity issues. Please try connecting again."
In order to resolve this error message, verify whether the Operating System (OS) that is used on the client machine is supported by the AnyConnect client. For complete information on supported software, refer to the System Requirements section in the AnyConnect Release Notes.
Error: "Secure VPN via remote desktop is not supported"
Users are unable to perform a remote desktop access. The Secure VPN via remote desktop is not supported error message appears.
This issue is due to these Cisco bug IDs: CSCsu22088 and CSCso42825. If you upgrade the AnyConnect VPN Client, it can resolve the issue. Refer to these bugs for more information.
Error: "The server certificate received or its chain does not comply with FIPS. A VPN connection will not be established"
When you attempt to VPN to the ASA 5505, the The server certificate received or its chain does not comply with FIPS. A VPN connection will not be established error message appears.
In order to resolve this error, you must disable the Federal Information Processing Standards (FIPS) in the AnyConnect Local Policy file. This file can usually be found at C:\ProgramData\Cisco\Cisco AnyConnect VPN Client\AnyConnectLocalPolicy.xml. If this file is not found in this path, then locate the file at a different directory with a path such as C:\Documents and Settings\All Users\Application Data\Cisco AnyConnectVPNClient\AnyConnectLocalPolicy.xml. Once you locate the xml file, make changes to this file as shown here:
Change the phrase:
Then, restart the computer. Users must have administrative permissions in order to modify this file.
Error: "Certificate Validation Failure"
Users are unable to launch AnyConnect and receive the Certificate Validation Failure error.
Certificate authentication works differently with AnyConnect compared to the IPSec client. In order for certificate authentication to work, you must import the client certificate to your browser and change the connection profile in order to use certificate authentication. You also need to enable this command on your ASA in order to allow SSL client-certificates to be used on the outside interface:
ssl certificate-authentication interface outside port 443
Error: "VPN Agent Service has encountered a problem and needs to close. We are sorry for the inconvenience"
When AnyConnect Version 2.4.0202 is installed on a Windows XP PC, it stops at updating localization files and an error message shows that the vpnagent.exe fails.
This behavior is logged in Cisco bug ID CSCsq49102. The suggested workaround is to disable the Citrix client.
Error: "This installation package could not be opened. Verify that the package exists"
When AnyConnect is downloaded, this error message is received:
"Contact your system administrator. The installer failed with the following error: This installation package could not be opened. Verify that the package exists and that you can access it, or contact the application vendor to verify that this is a valid Windows Installer package."
Complete these steps in order to fix this issue:
Remove any anti-virus software.
Disable the Windows firewall.
If neither Step 1 or 2 helps, then format the machine and then install.
Error: "Error applying transforms. Verify that the specified transform paths are valid."
This error message is recieved during the auto-download of AnyConnect from the ASA:
"Contact your system administrator. The installer failed with the following error: Error applying transforms. Verify that the specified transform paths are valid."
This is the error message received when connecting with AnyConnect for MacOS:
"The AnyConnect package on the secure gateway could not be located. You may be experiencing network connectivity issues. Please try connecting again."
Complete one of these workarounds in order to resolve this issue:
The root cause of this error might be due to a corrupted MST translation file (for example, imported). Perform these steps to fix this:
Remove the MST translation table.
Configure the AnyConnect image for MacOS in the ASA.
From the ASDM, follow the Network (Client) Access > AnyConnect Custom > Installs path and delete the AnyConnect package file. Make sure the package remains in Network (Client) Access > Advanced > SSL VPN > Client Setting.
Error: "The VPN client driver has encountered an error"
This error is received:
The VPN client driver has encountered an error when connecting through Cisco AnyConnect Client.
This issue can be resolved when you uninstall the AnyConnect Client, and then remove the anti-virus software. After this, reinstall the AnyConnect Client. If this resolution does not work, then reformat the PC in order to fix this issue.
Error: "A VPN reconnect resulted in different configuration setting. The VPN network setting is being re-initialized. Applications utilizing the private network may need to be restored."
This error is received when you try to launch AnyConnect:
"A VPN reconnect resulted in different configuration setting. The VPN network setting is being re-initialized. Applications utilizing the private network may need to be restarted."
In order to resolve this error, use this:
group-policy <Name> attributes webvpn svc mtu 1200
The svc mtu command is replaced by the anyconnect mtu command in ASA Version 8.4(1) and later as shown here:
hostname(config)#group-policy <Name> attributes
hostname(config-group-webvpn)#anyconnect mtu 500
AnyConnect Error While Logging In
The AnyConnect receives this error when it connects to the Client:
The VPN connection is not allowed via a local proxy. This can be changed through AnyConnect profile settings.
The issue can be resolved if you make these changes to the AnyConnect profile:
IE Proxy Setting is Not Restored after AnyConnect Disconnect on Windows 7
In Windows 7, if the IE proxy setting is configured for Automatically detect settings and AnyConnect pushes down a new proxy setting, the IE proxy setting is not restored back to Automatically detect settings after the user ends the AnyConnect session. This causes LAN issues for users who need their proxy setting configured for Automatically detect settings.
Error: AnyConnect Essentials can not be enabled until all these sessions are closed.
This error message is received on Cisco ASDM when you attempt to enable the AnyConnect Essentials license:
There are currently 2 clientless SSL VPN sessions in progress. AnyConnect Essentials can not be enabled until all these sessions are closed.
This is the normal behavior of the ASA. AnyConnect Essentials is a separately licensed SSL VPN client. It is entirely configured on the ASA and provides the full AnyConnect capability, with these exceptions:
No Cisco Secure Desktop (CSD) (including HostScan/Vault/Cache Cleaner)
No clientless SSL VPN
Optional Windows Mobile Support
This license cannot be used at the same time as the shared SSL VPN premium license. When you need to use one license, you need to disable the other.
Error: Connection tab on Internet option of Internet Explorer hides after getting connected to the AnyConnect client.
The connection tab on the Internet option of Internet Explorer hides after you are connected to the AnyConnect client.
This is due to the msie-proxy lockdown feature. If you enable this feature, it hides the Connections tab in Microsoft Internet Explorer for the duration of an AnyConnect VPN session. If you disable the feature, it leaves the display of the Connections tab unchanged.
Error: Few users getting Login Failed Error message when others are able to connect successfully through AnyConnect VPN
A few users receive the Login Failed Error message when others can connect successfully through the AnyConnect VPN.
This issue can be resolved if you make sure the do not require pre-authentication checkbox is checked for the users.
Error: The certificate you are viewing does not match with the name of the site you are trying to view.
During the AnyConnect profile update, an error is shown that says the certificate is invalid. This occurs with Windows only and at the profile update phase. The error message is shown here:
The certificate you are viewing does not match with the name of the site you are trying to view.
This can be resolved if you modify the server list of the AnyConnect profile in order to use the FQDN of the certificate.
This is a sample of the XML profile:
Note: If there is an existing entry for the Public IP address of the server such as <HostAddress>, then remove it and retain only the FQDN of the server (for example, <HostName> but not <Host Address>).
Cannot Launch AnyConnect From the CSD Vault From a Windows 7 Machine
When the AnyConnect is launched from the CSD vault, it does not work. This is attempted on Windows 7 machines.
Currently, this is not possible because it is not supported.
AnyConnect Profile Does Not Get Replicated to the Standby After Failover
The AnyConnect 3.0 VPN client with ASA Version 8.4.1 software works fine. However, after failover, there is no replication for the AnyConnect profile related configuration.
This problem has been observed and logged under Cisco bug ID CSCtn71662. The temporary workaround is to manually copy the files to the standby unit.
AnyConnect Client Crashes if Internet Explorer Goes Offline
When this occurs, the AnyConnect event log contains entries similar to these:
Description : Function: CAdapterNetworkStateIfc::SetConnectedStateToConnected File: .\AdapterNetworkStateIfc.cpp Line: 147 Invoked Function: InternetSetOption Return Code: 12010 (0x00002EEA) Description: The length is incorrect for the option type
The AnyConnect client fails to connect and the Unable to establish a connection error message is received. In the AnyConnect event log, the TLSPROTOCOL_ERROR_INSUFFICIENT_BUFFER error is found.
This occurs when the headend is configured for split-tunneling with a very large split-tunnel list (approximately 180-200 entries) and one or more other client attributes are configured in the group-policy, such as dns-server.
In order to resolve this issue, complete these steps:
Reduce the number of entries in the split-tunnel list.
For more information, refer to Cisco bug ID CSCtc41770.
Error Message: "Connection attempt has failed due to invalid host entry"
The Connection attempt has failed due to invalid host entry error message is received while AnyConnect is authenticated with the use of a certificate.
In order to resolve this issue, try either of these possible solutions:
Upgrade the AnyConnect to Version 3.0.
Disable Cisco Secure Desktop on your computer.
For more information, refer to Cisco bug ID CSCti73316.
Error: "Ensure your server certificates can pass strict mode if you configure always-on VPN"
When you enable the Always-On feature on AnyConnect, the Ensure your server certificates can pass strict mode if you configure always-on VPN error message is received.
This error message implies that if you want to use the Always-On feature, you need a valid sever certificate configured on the headend. Without a valid server certificate, this feature does not work. Strict Cert Mode is an option that you set in the AnyConnect local policy file in order to ensure the connections use a valid certificate. If you enable this option in the policy file and connect with a bogus certificate, the connection fails.
Error: "Connection Attempt Failed"
This Diagnostic AnyConnect Reporting Tool (DART) shows one failed attempt:
****************************************** Date : 03/25/2014 Time : 09:52:21 Type : Error Source : acvpnui
Description : Function: CTransportWinHttp::SendRequest File: .\CTransportWinHttp.cpp Line: 1170 Invoked Function: HttpSendRequest Return Code: 12004 (0x00002EE4) Description: An internal error occurred in the Microsoft Windows HTTP Services ***************************************** Date : 03/25/2014 Time : 09:52:21 Type : Error Source : acvpnui
Description : Function: ConnectIfc::connect File: .\ConnectIfc.cpp Line: 472 Invoked Function: ConnectIfc::sendRequest Return Code: -30015443 (0xFE36002D) Description: CTRANSPORT_ERROR_CONN_UNKNOWN ****************************************** Date : 03/25/2014 Time : 09:52:21 Type : Error Source : acvpnui