Cisco IR800 Series Router Factory Default Settings

Introduction

This document describes how to reset Cisco IR829 devices to its default configuration.

Prerequisites

Requirements

Cisco recommends that you have knowledge of these topics:

• Console access to the device
• Paper clip to press the reset button

Components Used

The information in this document is based on Cisco IR829 Router.

The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.

Background Information

The rommon in IR800 series routers is totally different from the rommon found in most other Cisco devices. 

You cannot do a password recovery on IR800 series routers in the usual sense because IR800 series routers do not support the config-register setting to allow you to bypass the startup-config. You can only "recover” your routerwhen you wipe out its startup-config.  Ensure you save a copy of your working running-config to a file on flash, just in case you can need it again later on. It has a Reset button to reset the device to its factory-default settings.

Note: There is no way to recover the startup configuration once the device is Reset.

Procedure

Method 1. For Cisco IOS® Version 15.5(3)M5 or Earlier

If the version of the Cisco IOS® is 15.5(3)M5 or earlier, then the device must be booted to password prompt before you reset the device.

Once you see the password prompt, long press the reset button for 30 seconds until this message appears:

*Jan 28 05:21:24.143: %FCPLMGR-5-CFG_BUTTON_LONG_PRESSED: Config reset button was held for more than 10 seconds. NVRAM filesystem erased.
*Jan 28 05:21:24.145: %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
*Jan 28 05:21:24.145: %SYS-5-RELOAD: Reload requested by IR800 Fcplmgr OS events dispatcher. Reload Reason: Configuration Reset button (long) pressed.
%FCPLMGR-5-CFG_BUTTON_LONG_PRESSED: Config reset button was held for more than 10 seconds. NVRAM filesystem erased.

This erases the content of the NVRAM and the device reboots itself in rommon-2 prompt.

Boot the IOx from the rommon-2 prompt. The IOx image starts the boot sequence and once completed, the device must come up with factory default settings.

rommon-2>boot flash:ir800-universalk9-mz.SPA.155-3.M5

Booting image: flash:ir800-universalk9-mz.SPA.155-3.M5....   [Multiboot-elf, <0

x110000:0x988e584:0x48c5c4>, shtab=0x9e2b500

Signature verification was successful, entry=0x110240]

[CU:0]

Jumps to: 0x110240

 
Smart Init is enabled

smart init is sizing iomem

                 TYPE      MEMORY_REQ

    Onboard devices &

         buffer pools      0x02E44000

-----------------------------------------------

               TOTAL:      0x02E44000

 
Rounded IOMEM up to: 47MB.

Using 10 percent iomem. [47MB/448MB]

 
              Restricted Rights Legend

 
Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

 
           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

 
 
 
Cisco IOS® Software, ir800 Software (ir800-UNIVERSALK9-M), Version 15.5(3)M5, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2016 by Cisco Systems, Inc.

Compiled Mon 20-Jun-16 15:52 by prod_rel_team

 
 
This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

 
A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

 
If you require further assistance please contact us by sending email to

export@cisco.com.

 
Cisco IR829GW-LTE-GA-ZK9 (revision 2.0) with 373760K/52224K bytes of memory.

Processor board ID FGL192420ZL

Last reset from CLI initiated reload

 
FPGA version: 2.0.0

 
2 Serial(sync/async) interfaces

7 Gigabit Ethernet interfaces

9 terminal lines

2 Cellular interfaces

1 cisco Embedded AP (s)

DRAM configuration is 72 bits wide with parity disabled.

256K bytes of non-volatile configuration memory.

976562K bytes of ATA System Flash (Read/Write)

250000K bytes of ATA Bootstrap Flash (Read/Write)

 
%Error opening tftp://255.255.255.255/network-confg (Timed out)

%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)

         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no

Press RETURN to get started!

IR800>en

IR800# 

Method 2. For Cisco IOS® Version 15.6 or Later

If the Cisco IOS® version is 15.6 and later, power off the device and simultaneously press the reset button while you apply power to the device.

Hold the reset button for about 30 seconds until the Protocol over Ethernet (PoE) light comes on and then release the button.

Cisco IOS® Software, ir800 Software (ir800-UNIVERSALK9-M), Version 15.6(1)T1, RELEASE SOFTWARE (fc1)
 Technical Support: http://www.cisco.com/techsupport
 Copyright (c) 1986-2016 by Cisco Systems, Inc.
 Compiled Mon 29-Feb-16 10:51 by prod_rel_team
   This product contains cryptographic features and is subject to United
 States and local country laws governing import, export, transfer and
 use. Delivery of Cisco cryptographic products does not imply
 third-party authority to import, export, distribute or use encryption.
 Importers, exporters, distributors and users are responsible for
 compliance with U.S. and local country laws. By using this product you
 agree to comply with applicable laws and regulations. If you are unable
 to comply with U.S. and local laws, return this product immediately.
   A summary of U.S. laws governing Cisco cryptographic products may be found at:
 <ahref="http: www.cisco.com="" wwl="" export="" crypto="" tool="" stqrg.html"="">http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
   If you require further assistance please contact us by sending email to
 export@cisco.com.
   Cisco IR829GW-LTE-GA-ZK9 (revision 2.0) with 373760K/52224K bytes of memory.
 Processor board ID FGL192420ZL
 Last reset from Power-on
   FPGA version: 2.2.0
   BIOS: version 9 Production
 BIOS: date[YYYY/MM/DD] :[2015/8/21]
   MCU Bootloader : 28
 MCU Application: 0
   2 Serial(sync/async) interfaces
 7 Gigabit Ethernet interfaces
 9 terminal lines
 2 Cellular interfaces
 1 cisco Embedded AP (s)
 DRAM configuration is 72 bits wide with parity disabled.
 256K bytes of non-volatile configuration memory.
 976562K bytes of ATA System Flash (Read/Write)
 250000K bytes of ATA Bootstrap Flash (Read/Write)
   Erasing the nvram filesystem will remove all files! Continue? [OK]
 Erase of nvram: complete
 Router IOS Configuration Recovery is unsuccessful
   Router Configuration Dialogue will be used
                       --- System Configuration Dialog ---
 Would you like to enter the initial configuration dialog? [yes/no]: no
 Press RETURN to get started!
 IR800>en
 IR800#