Summary

• A vulnerability in the web UI of Cisco IOS and Cisco IOS XE Software could allow an unauthenticated, remote attacker to conduct a cross-site request forgery (CSRF) attack on an affected system.

  The vulnerability is due to insufficient CSRF protections for the web UI on an affected device. An attacker could exploit this vulnerability by persuading a user of the interface to follow a malicious link. A successful exploit could allow the attacker to perform arbitrary actions with the privilege level of the targeted user. If the user has administrative privileges, the attacker could alter the configuration, execute commands, or reload an affected device.

  Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.

  This advisory is available at the following link:
  https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20200108-ios-csrf

Affected Products

• Vulnerable Products

  This vulnerability affects Cisco devices that are running a vulnerable release of Cisco IOS or Cisco IOS XE Software earlier than 16.1.1 with the HTTP Server feature enabled. The default state of the HTTP Server feature in Cisco IOS and Cisco IOS XE Software is version dependent.

  For information about which Cisco IOS and Cisco IOS XE Software releases are vulnerable, see the Fixed Software section of this advisory.

  Determine the HTTP Server Configuration

  To determine whether the HTTP Server feature is enabled for a device, administrators can log in to the device and use the show running-config | include ip http server|secure|active command in the CLI to check for the presence of the ip http server command or the ip http secure-server command in the global configuration. If either command is present and configured, the HTTP Server feature is enabled for the device.

  The following example shows the output of the show running-config | include ip http server|secure|active command for a device that has the HTTP Server feature enabled:

  Router# show running-config | include ip http server|secure|active
  
  ip http server
  ip http secure-server

  Note: The presence of either command, or both commands, in the device configuration indicates that the web UI feature is enabled.

  If the ip http server command is present and the configuration also contains ip http active-session-modules none, the vulnerability is not exploitable over HTTP.

  If the ip http secure-server command is present and the configuration also contains ip http secure-active-session-modules none, the vulnerability is not exploitable over HTTPS.

  Products Confirmed Not Vulnerable

  Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.

  Cisco has confirmed that this vulnerability does not affect Cisco IOS XR Software or Cisco NX-OS Software.

Workarounds

• There are no workarounds that address this vulnerability.

  Disabling the HTTP Server feature eliminates the attack vector for this vulnerability and may be a suitable mitigation until affected devices can be upgraded. Administrators can disable the HTTP Server feature by using the no ip http server or no ip http secure-server command in global configuration mode. If both http server and http-secure server are in use, then both commands are required to disable the HTTP Server feature.

Fixed Software

• Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:
  https://www.cisco.com/c/en/us/products/end-user-license-agreement.html

  Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.

  When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page, to determine exposure and a complete upgrade solution.

  In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.

  Customers Without Service Contracts

  Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC:
  https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html

  Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.

  Cisco IOS and IOS XE Software

  To help customers determine their exposure to vulnerabilities in Cisco IOS and IOS XE Software, Cisco provides a tool, the Cisco IOS Software Checker, that identifies any Cisco Security Advisories that impact a specific software release and the earliest release that fixes the vulnerabilities described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities described in all the advisories identified (“Combined First Fixed”).

  Customers can use this tool to perform the following tasks:

  • Initiate a search by choosing one or more releases from a drop-down list or uploading a file from a local system for the tool to parse
  • Enter the output of the show version command for the tool to parse
  • Create a custom search by including all previously published Cisco Security Advisories, a specific advisory, or all advisories in the most recent bundled publication

  To determine whether a release is affected by any published Cisco Security Advisory, use the Cisco IOS Software Checker on Cisco.com or enter a Cisco IOS or IOS XE Software release—for example, 15.1(4)M2 or 3.13.8S—in the following field:

  By default, the Cisco IOS Software Checker includes results only for vulnerabilities that have a Critical or High Security Impact Rating (SIR). To include results for Medium SIR vulnerabilities, use the Cisco IOS Software Checker on Cisco.com and check the Medium check box in the Impact Rating drop-down list.

Exploitation and Public Announcements

• The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.

Source

• Cisco would like to thank Mehmet Önder Key for reporting this vulnerability.

URL

• https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20200108-ios-csrf

Revision History

• Version	Description	Section	Status	Date
  1.1	Changed "show running-config | include ip http server|secure" to "show running-config | include ip http server|secure|active".	Affected Products	Final	2020-APR-28
  1.0	Initial public release.	—	Final	2020-JAN-08

  Show Less

---