Summary

• A vulnerability in the TCP ingress handler for the data interfaces that are configured with management access to Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an increase in CPU and memory usage, resulting in a denial of service (DoS) condition.

  The vulnerability is due to insufficient ingress TCP rate limiting for TCP ports 22 (SSH) and 443 (HTTPS). An attacker could exploit this vulnerability by sending a crafted, steady stream of TCP traffic to port 22 or 443 on the data interfaces that are configured with management access to the affected device.

  Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.

  This advisory is available at the following link:
  https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190501-firepower-dos

Affected Products

• Vulnerable Products

  This vulnerability affects the following Cisco products that are running a vulnerable release of Cisco FTD Software:

  • 3000 Series Industrial Security Appliances (ISAs)
  • Adaptive Security Appliance (ASA) 5500-X Series Firewalls
  • Firepower 2100 Series
  • Firepower 4100 Series
  • Firepower 9300 Security Appliances
  • FTD Virtual (FTDv)

  For information about which Cisco FTD Software releases are vulnerable, see the Fixed Software section of this advisory.

  Determining the Cisco FTD Software Release

  To determine which Cisco FTD Software release is running on a device, administrators can log in to the device, use the show version command in the CLI, and refer to the output of the command. The following example shows the output of the command for a device that is running Cisco FTD Software Release 6.2.0:

  > show version
  
  ---------------------[ ftd ]---------------------
  Model : Cisco ASA5525-X Threat Defense (75) Version 6.2.0 (Build 362)
  UUID : 2849ba3c-ecb8-11e6-98ca-b9fc2975893c
  Rules update version : 2017-03-15-001-vrt
  VDB version : 279
  ----------------------------------------------------

  Determining the SSH and HTTP Service Configurations

  In the following table, the left column lists the Cisco FTD features that may be vulnerable. The right column indicates the basic configuration for the feature from the show running-config CLI command, if it can be determined. If the device is configured with any of these features, the device is affected by the vulnerability described in this advisory.

  Cisco FTD Feature	Vulnerable Configuration
  HTTP service enabled1,2	http server enable <port> http <remote_ip_address> <remote_subnet_mask> <interface_name>
  SSH service enabled1,3	ssh <remote_ip_address> <remote_subnet_mask> <interface_name>

  ¹ The device is vulnerable only from an IP address in the configured HTTP or SSH command range.
  ² All devices configured for FDM access have the HTTP service enabled.
  ³ All devices that are managed by FMC have the SSH service enabled.
  

  Products Confirmed Not Vulnerable

  Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.

  Cisco has confirmed that this vulnerability does not affect Cisco Adaptive Security Appliance (ASA) Software.

Workarounds

• There are no workarounds that address this vulnerability.

Fixed Software

• Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:
  https://www.cisco.com/c/en/us/products/end-user-license-agreement.html

  Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.

  When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page, to determine exposure and a complete upgrade solution.

  In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.

  Customers Without Service Contracts

  Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC:
  https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html

  Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.

  Fixed Releases

  Customers are advised to upgrade to an appropriate release as indicated in the applicable table in this section. To ensure a complete upgrade solution, customers should consider that this advisory is part of a collection that includes the following advisories:

  • cisco-sa-20190501-asa-csrf: Cisco Adaptive Security Appliance Software Cross-Site Request Forgery Vulnerability
  • cisco-sa-20190501-asa-frpwrtd-dos: Cisco Adaptive Security Appliance Software and Cisco Firepower Threat Defense Software TCP Timer Handling Denial of Service Vulnerability
  • cisco-sa-20190501-asa-ftd-dos: Cisco Adaptive Security Appliance Software and Firepower Threat Defense Software WebVPN Denial of Service Vulnerability
  • cisco-sa-20190501-asa-ftd-entropy: Cisco Adaptive Security Appliance Software and Firepower Threat Defense Software Low-Entropy Keys Vulnerability
  • cisco-sa-20190501-asa-ftd-ike-dos: Cisco Adaptive Security Appliance Software and Cisco Firepower Threat Defense Software MOBIKE Denial of Service Vulnerability
  • cisco-sa-20190501-asaftd-saml-vpn: Cisco Adaptive Security Appliance Software and Firepower Threat Defense Software VPN SAML Authentication Bypass Vulnerability
  • cisco-sa-20190501-asa-ipsec-dos: Cisco Adaptive Security Appliance Software IPsec Denial of Service Vulnerability
  • cisco-sa-20190501-firepower-dos: Cisco Firepower Threat Defense Software TCP Ingress Handler Denial of Service Vulnerability
  • cisco-sa-20190501-frpwr-dos: Cisco Firepower Threat Defense Software Packet Processing Denial of Service Vulnerability
  • cisco-sa-20190501-frpwr-smb-snort: Cisco Firepower Threat Defense Software SMB Protocol Preprocessor Detection Engine Denial of Service Vulnerabilities
  • cisco-sa-20190501-sd-cpu-dos: Cisco Adaptive Security Appliance Software and Firepower Threat Defense Software WebVPN Denial of Service Vulnerability

  In the following table(s), the left column lists Cisco software releases. The center column indicates whether a release is affected by the vulnerability described in this advisory and the release that includes the fix for this vulnerability. The right column indicates whether a release is affected by all the vulnerabilities described in this collection of advisories and which release includes fixes for those vulnerabilities.

  Cisco FTD Software

  Cisco FTD Software Release	Recommended Release for This Vulnerability	Recommended Release for All Vulnerabilities Described in the Collection of Advisories
  6.0	6.2.3.12	6.2.3.12
  6.0.1	6.2.3.12	6.2.3.12
  6.1.0	6.2.3.12	6.2.3.12
  6.2.0	6.2.3.12	6.2.3.12
  6.2.1	6.2.3.12	6.2.3.12
  6.2.2	6.2.3.12	6.2.3.12
  6.2.3	6.2.3.12	6.2.3.12
  6.3.0	6.3.0.3	6.3.0.3
  6.4.0	Not vulnerable	Not vulnerable

  To upgrade to a fixed release of Cisco FTD Software, customers can do one of the following:

  • For devices that are managed by using Cisco Firepower Management Center (FMC), use the FMC interface to install the upgrade. After installation is complete, reapply the access control policy.
  • For devices that are managed by using Cisco Firepower Device Manager (FDM), use the FDM interface to install the upgrade. After installation is complete, reapply the access control policy.

Exploitation and Public Announcements

• The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.

Source

• This vulnerability was found during the resolution of a Cisco TAC support case.

URL

• https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20190501-firepower-dos

Revision History

• Version	Description	Section	Status	Date
  1.1	Updated the FTD fixed releases table to indicate that FTD Software Release 6.3.0.3 is available.	Fixed Software	Final	2019-May-02
  1.0	Initial public release.	—	Final	2019-May-01

  Show Less

---