show コマンド:802.11

show 802.11

802.11a、802.11b/g、または 802.11h の基本的なネットワーク設定を表示するには、show 802.11 コマンドを使用します。

show 802.11 { a | b | h }

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

コマンド デフォルト

なし。

次に、802.11a の基本的なネットワーク設定を表示する例を示します。


>  show 802.11a
802.11a Network.................................. Enabled
11nSupport....................................... Enabled
      802.11a Low Band........................... Enabled
      802.11a Mid Band........................... Enabled
      802.11a High Band.......................... Enabled
802.11a Operational Rates
    802.11a 6M Rate.............................. Mandatory
    802.11a 9M Rate.............................. Supported
    802.11a 12M Rate............................. Mandatory
    802.11a 18M Rate............................. Supported
    802.11a 24M Rate............................. Mandatory
    802.11a 36M Rate............................. Supported
    802.11a 48M Rate............................. Supported
    802.11a 54M Rate............................. Supported
802.11n MCS Settings:
    MCS 0........................................ Supported
    MCS 1........................................ Supported
    MCS 2........................................ Supported
    MCS 3........................................ Supported
    MCS 4........................................ Supported
    MCS 5........................................ Supported
    MCS 6........................................ Supported
    MCS 7........................................ Supported
    MCS 8........................................ Supported
    MCS 9........................................ Supported
    MCS 10....................................... Supported
    MCS 11....................................... Supported
    MCS 12....................................... Supported
    MCS 13....................................... Supported
    MCS 14....................................... Supported
    MCS 15....................................... Supported
802.11n Status:
    A-MPDU Tx:
        Priority 0............................... Enabled
        Priority 1............................... Disabled
        Priority 2............................... Disabled
        Priority 3............................... Disabled
        Priority 4............................... Disabled
        Priority 5............................... Disabled
        Priority 6............................... Disabled
        Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
--More-- or (q)uit
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Enabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC:
   Voice AC - Admission control (ACM)............ Disabled
   Voice max RF bandwidth........................ 75
   Voice reserved roaming bandwidth.............. 6
   Voice load-based CAC mode..................... Disabled
   Voice tspec inactivity timeout................ Disabled
   Voice Stream-Size............................. 84000
   Voice Max-Streams............................. 2
Video AC:
   Video AC - Admission control (ACM)............ Disabled
   Video max RF bandwidth........................ Infinite
   Video reserved roaming bandwidth.............. 0

次に、802.11h の基本的なネットワーク設定を表示する例を示します。


>  show 802.11h
802.11h ......................................... powerconstraint : 0
802.11h ......................................... channelswitch : Disable
802.11h ......................................... channelswitch mode : 0

show 802.11

802.11a、802.11b/g、または 802.11h の基本的なネットワーク設定を表示するには、show 802.11 コマンドを使用します。

show 802.11 { a | b | h }

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

コマンド デフォルト

なし。

次に、802.11a の基本的なネットワーク設定を表示する例を示します。


>  show 802.11a
802.11a Network.................................. Enabled
11nSupport....................................... Enabled
      802.11a Low Band........................... Enabled
      802.11a Mid Band........................... Enabled
      802.11a High Band.......................... Enabled
802.11a Operational Rates
    802.11a 6M Rate.............................. Mandatory
    802.11a 9M Rate.............................. Supported
    802.11a 12M Rate............................. Mandatory
    802.11a 18M Rate............................. Supported
    802.11a 24M Rate............................. Mandatory
    802.11a 36M Rate............................. Supported
    802.11a 48M Rate............................. Supported
    802.11a 54M Rate............................. Supported
802.11n MCS Settings:
    MCS 0........................................ Supported
    MCS 1........................................ Supported
    MCS 2........................................ Supported
    MCS 3........................................ Supported
    MCS 4........................................ Supported
    MCS 5........................................ Supported
    MCS 6........................................ Supported
    MCS 7........................................ Supported
    MCS 8........................................ Supported
    MCS 9........................................ Supported
    MCS 10....................................... Supported
    MCS 11....................................... Supported
    MCS 12....................................... Supported
    MCS 13....................................... Supported
    MCS 14....................................... Supported
    MCS 15....................................... Supported
802.11n Status:
    A-MPDU Tx:
        Priority 0............................... Enabled
        Priority 1............................... Disabled
        Priority 2............................... Disabled
        Priority 3............................... Disabled
        Priority 4............................... Disabled
        Priority 5............................... Disabled
        Priority 6............................... Disabled
        Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
--More-- or (q)uit
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Enabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC:
   Voice AC - Admission control (ACM)............ Disabled
   Voice max RF bandwidth........................ 75
   Voice reserved roaming bandwidth.............. 6
   Voice load-based CAC mode..................... Disabled
   Voice tspec inactivity timeout................ Disabled
   Voice Stream-Size............................. 84000
   Voice Max-Streams............................. 2
Video AC:
   Video AC - Admission control (ACM)............ Disabled
   Video max RF bandwidth........................ Infinite
   Video reserved roaming bandwidth.............. 0

次に、802.11h の基本的なネットワーク設定を表示する例を示します。


>  show 802.11h
802.11h ......................................... powerconstraint : 0
802.11h ......................................... channelswitch : Disable
802.11h ......................................... channelswitch mode : 0

show 802.11 cleanair

マルチキャスト ダイレクト設定の状態を表示するには、show 802.11 cleanair コマンドを使用します。

show 802.11 { a | b | h } cleanair config

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

config

ネットワークの cleanair の設定を表示します。

コマンド デフォルト

なし

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。

次に、802.11a cleanair の設定を表示する例を示します。


(Cisco Controller) > show 802.11a cleanair
Clean Air Solution............................... Enabled
Air Quality Settings:
    Air Quality Reporting........................ Enabled
    Air Quality Reporting Period (min)........... 15
    Air Quality Alarms........................... Enabled
    Air Quality Alarm Threshold.................. 35 Interference Device Settings:
    Interference Device Reporting................ Enabled
    Interference Device Types:
        TDD Transmitter.......................... Disabled
        Jammer................................... Disabled
        Continuous Transmitter................... Disabled
        DECT-like Phone.......................... Disabled
        Video Camera............................. Disabled
        WiFi Inverted............................ Disabled
        WiFi Invalid Channel..................... Disabled
        SuperAG.................................. Disabled
        Radar.................................... Disabled
        Canopy................................... Disabled
        WiMax Mobile............................. Disabled
        WiMax Fixed.............................. Disabled
Interference Device Alarms................... Enabled
    Interference Device Types Triggering Alarms:
        TDD Transmitter.......................... Disabled
        Jammer................................... Disabled
        Continuous Transmitter................... Disabled
        DECT-like Phone.......................... Disabled
        Video Camera............................. Disabled
        WiFi Inverted............................ Disabled
        WiFi Invalid Channel..................... Disabled
        SuperAG.................................. Disabled
        Radar.................................... Disabled
        Canopy................................... Disabled
        WiMax Mobile............................. Disabled
        WiMax Fixed.............................. Disabled Additional Clean Air Settings:
    CleanAir Event-driven RRM State.............. Enabled
    CleanAir Driven RRM Sensitivity.............. Medium
    CleanAir Persistent Devices state............ Disabled

show 802.11 cleanair air-quality summary

802.11 ネットワークの電波品質のサマリー情報を表示するには、show 802.11 cleanair air-quality summary コマンドを使用します。

show 802.11 { a | b | h } cleanair air-quality summary

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

summary

802.11 無線帯域電波品質情報のサマリーを表示します。

コマンド デフォルト

なし

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。

次に、802.11a ネットワークの電波品質のサマリー情報を表示する例を示します。


(Cisco Controller) > show 802.11a cleanair air-quality summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name            Channel 	Avg AQ 	Min AQ 	Interferers 	DFS
------------------ ------- 	------ 	------ 	----------- 	---
CISCO_AP3500			 	 	36			95	 70			0
CISCO_AP3500					40			93	 75			0

show 802.11 cleanair air-quality worst

802.11 ネットワークの最も深刻な電波品質の情報を表示するには、show 802.11 cleanair air-quality worst コマンドを使用します。

show 802.11 { a | b | h } cleanair air-quality worst

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

worst

802.11 ネットワークの最も深刻な電波品質の情報を表示します。

コマンド デフォルト

なし

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。

次に、802.11a ネットワークの最も深刻な電波品質の情報を表示する例を示します。


(Cisco Controller) > show 802.11 cleanair air-quality worst
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name            Channel 	Avg AQ 	Min AQ 	Interferers 	DFS
------------------ ------- 	------ 	------ 	----------- 	---
CISCO_AP3500			 	 	1			83	 57			3		 5

show 802.11 cleanair device ap

802.11 無線帯域のデバイス アクセス ポイントの情報を表示するには、show 802.11 cleanair device ap コマンドを使用します。

show 802.11 { a | b | h } cleanair device ap cisco_ap

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

cisco_ap

特定のアクセス ポイント名。

コマンド デフォルト

なし

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。

次に、802.11a ネットワークのデバイス アクセス ポイントを表示する例を示します。

(Cisco Controller) > show 802.11a cleanair device ap AP_3500
DC = Duty Cycle (%)
ISI = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID
No  ClusterID          DevID  Type 	 	 	 	 	 	 AP Name 			 	 	 	 	 ISI  RSSI 	 DC   Channel
--- ------------------ ------ ---------- --------------- ---- ----- ---- -------------
1   c2:f7:40:00:00:03  0x8001 DECT phone 	CISCO_AP3500 	1    -43 	 	 3 	 	 	149,153,157,161
2   c2:f7:40:00:00:51  0x8002 Radar		 	 	 CISCO_AP3500 	1    -81 		 	2 	 	153,157,161,165
3   c2:f7:40:00:00:03  0x8005 Canopy	 	 	 CISCO_AP3500 	2    -62	 	 	2 	 	 153,157,161,165

show 802.11 cleanair device type

802.11 無線帯域の特定のアクセス ポイントによって検出されたすべての干渉デバイス タイプの情報を表示するには、show 802.11 cleanair device type コマンドを使用します。

show 802.11 { a | b | h } cleanair device type device_type

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

device_type

指定した無線帯域の干渉デバイスのタイプ。デバイス タイプは次のいずれかです。

  • tdd-tx:Tdd トランスミッタのデバイス情報。

  • jammer:電波妨害デバイス情報。

  • cont-tx:連続トランスミッタのデバイス情報。

  • dect-like:Dect-like 電話デバイス情報。

  • video:ビデオ デバイス情報。

  • 802.11-inv:WiFi 反転デバイス情報。

  • 802.11-nonstd:非標準 WiFi デバイス情報。

  • superag:Superag デバイス情報。

  • canopy:Canopy デバイス情報。

  • wimax-mobile:WiMax モバイル デバイス情報。

  • wimax-fixed:WiMax 固定デバイス情報。

コマンド デフォルト

なし

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。

次に、802.11a ネットワークに指定されたアクセス ポイントによって検出されたすべての干渉源情報を表示する例を示します。


(Cisco Controller) > show 802.11a cleanair device type canopy
DC = Duty Cycle (%)
ISI = Interference Severity Index (1-Low Interference, 100-High Interference)
RSSI  = Received Signal Strength Index (dBm)
DevID = Device ID
No  ClusterID          DevID  Type 	 	 	 	 	 	 AP Name 			 	 	 	 	 ISI  RSSI 	 DC   Channel
--- ------------------ ------ ---------- --------------- ---- ----- ---- -------------
1c2:f7:40:00:00:03  0x8005 Canopy	 	 	 	 	 CISCO_AP3500 	2    -62	 	 	 2 	 	 153,157,161,165

show 802.11 cu-metrics

アクセス ポイントのチャネル使用率メトリックを表示するには、show 802.11 cu-metrics コマンドを使用します。

show 802.11 { a | b } cu-metrics cisco_ap

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

cisco_ap

アクセス ポイント名。

コマンド デフォルト

なし

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。

次に、show 802.11a cu-metrics コマンドの出力例を示します。


(Cisco Controller) > show 802.11a cu-metrics AP1
AP Interface Mac:           30:37:a6:c8:8a:50
Measurement Duration:       90sec
 Timestamp               Thu Jan 27 09:08:48 2011
   Channel Utilization stats
   ================
     Picc (50th Percentile)...................... 0
     Pib (50th Percentile)....................... 76
     Picc (90th Percentile)...................... 0
     Pib (90th Percentile)....................... 77
 Timestamp               Thu Jan 27 09:34:34 2011

show 802.11 extended

アクセス ポイント無線の拡張設定を表示するには、show 802.11 extended コマンドを使用します。

show 802.11 { a | b } extended

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

extended

802.11a/b 無線の拡張設定を表示します。

コマンド デフォルト

なし

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。
8.0

コマンド出力は、Rx SOP しきい値を含むように拡張されました。

次に、無線の拡張設定を表示する例を示します。


(Cisco Controller) > show 802.11a extended 
Default 802.11a band radio extended configurations:
    beacon period 300, range 60;
    multicast buffer 45, rate 200;
    RX SOP -80; CCA threshold -90;
AP0022.9090.b618 00:24:97:88:99:60
    beacon period 300, range 60; multicast buffer 45, rate 200;
    RX SOP -80; CCA threshold -77
AP0022.9090.bb3e 00:24:97:88:c5:d0
    beacon period 300, range 0; multicast buffer 0, rate 0;
    RX SOP -80; CCA threshold -0
ironRap.ddbf 00:17:df:36:dd:b0
    beacon period 300, range 0; multicast buffer 0, rate 0;
    RX SOP  -80; CCA threshold -0

次に、無線の拡張設定および Rx SOP しきい値を表示する例を示します。

(Cisco Controller) > show 802.11a extended 
Default 802.11a band Radio Extended Configurations:
    Beacon period: 100, range: 0 (AUTO);
    Multicast buffer: 0 (AUTO), rate: 0 (AUTO);
    RX SOP threshold: -76; CCA threshold: 0 (AUTO);

AP3600-XALE3  34:a8:4e:6a:7b:00
    Beacon period: 100, range: 0 (AUTO);
    Multicast buffer: 0 (AUTO), rate: 0 (AUTO);
    RX SOP threshold: -76; CCA threshold: 0 (AUTO);

show 802.11 media-stream

マルチキャスト ダイレクト設定の状態を表示するには、show 802.11 media-stream コマンドを使用します。

show 802.11 { a | b | h } media-stream media_stream_name

構文の説明

a

802.11a ネットワークを指定します。

b

802.11b/g ネットワークを指定します。

h

802.11h ネットワークを指定します。

media_stream_name

指定されたメディア ストリーム名。

コマンド デフォルト

なし。

コマンド履歴

リリース 変更内容
7.6 このコマンドは、リリース 7.6 以前のリリースで導入されました。

次に、メディア ストリームの設定を表示する例を示します。


> show 802.11a media-stream rrc
Multicast-direct................................. Enabled
Best Effort...................................... Disabled
Video Re-Direct.................................. Enabled
Max Allowed Streams Per Radio.................... Auto
Max Allowed Streams Per Client................... Auto
Max Video Bandwidth.............................. 0
Max Voice Bandwidth.............................. 75
Max Media Bandwidth.............................. 85
Min PHY Rate..................................... 6000
Max Retry Percentage............................. 80