Command Line Interface Reference, Commands I - Q, StarOS Release 20

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents

Find Matches in This Book

Results

Updated:: March 31, 2016

Chapter: Linkset Configuration Mode Commands

adjacent-point-code
end
exit
link
self-point-code

Linkset Configuration Mode Commands

Mode

The Linkset configuration mode defines the MTP3 linkset parameters for a specific SS7 routing domain instance.

Exec > Global Configuration > SS7 Routing Domain Configuration > Linkset Configuration

configure > ss7-routing-domain domain_id variant var_type > linkset id linkset_id

Entering the above command sequence results in the following prompt:

[local]host_name(config-ss7-rd-linkset-linkset_id)#

Important:

The commands or keywords/variables that are available are dependent on platform type, product version, and installed license(s).

adjacent-point-code
end
exit
link
self-point-code

adjacent-point-code

This command defines the point-code for the adjacent (next) network element in the SS7 network.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SS7 Routing Domain Configuration > Linkset Configuration

configure > ss7-routing-domain domain_id variant var_type > linkset id linkset_id

Entering the above command sequence results in the following prompt:

[local]host_name(config-ss7-rd-linkset-linkset_id)#

Syntax

Syntax Description

adjacent-point-code point-code
no adjacent-point-code

point-code

Point-code is an SS7 address for an element in the SS7 network. Point-codes must be defined in dotted-decimal format in a string of 1 to 11 digits. Format options include:

0.0.1 to 7.255.7 for point-code in the ITU range.
0.0.1 to 255.255.255 for point-code in the ANSI range.
0.0.1 to 15.31.255 for point-code in the TTC range.
a string of 1 to 11 digits in dotted-decimal to represent a point-code in a different range.

no

Removes the adjacent-point-code configuration for this linkset in the SS7 routing domain

Important:

Removing the linkset configuration will result in the termination of all of the links within the linkset.

Usage Guidelines

Use this command to define the point-code for the adjacent element in the SS7 network.

Examples

adjacent-point-code 6.202.7

end

Exits the current configuration mode and returns to the Exec mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

Syntax Description

end

Usage Guidelines

Use this command to return to the Exec mode.

exit

Exits the current mode and returns to the parent configuration mode.

Product

All

Privilege

Security Administrator, Administrator

Syntax

Syntax Description

exit

Usage Guidelines

Use this command to return to the parent configuration mode.

link

This command creates an MTP3 link configuration for the SS7 linkset and enters the Link configuration mode.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SS7 Routing Domain Configuration > Linkset Configuration

configure > ss7-routing-domain domain_id variant var_type > linkset id linkset_id

Entering the above command sequence results in the following prompt:

[local]host_name(config-ss7-rd-linkset-linkset_id)#

Syntax

Syntax Description

link id id [ link-type [ atm-broadband | highspeed-narrowband | lowspeed-narrowband ]
no link id id

no

Disables the specified link configuration.

Important:

Removing the link configuration will result in the termination of traffic on the specified link.

#_octets

Sets the number of octets for the length of the LSSU.

id

This number uniquely identifies the link in the linkset.

id: an integer between 1 and 16.

link-type

Identifies the signalling type for this link; options include:

ATM broadband -- ATM AAL5 over an optical line card (OLC2)
high speed-narrowband -- 64 kbps over a channelized optical line card (CLC2)
low speed-narrowband -- 4.8 kbps over a channelized optical line card (CLC2)

Important:

Be default link-type is ATM-broadband. To support narrowband SS7, one of the other options must be set.

Usage Guidelines

Access the Link configuration mode to configure the parameters for the the link.

Examples

Access configuration for link 4:

link id 4

self-point-code

This command defines the SS7 network point-code to identify this SGSN.

Product

SGSN

Privilege

Security Administrator, Administrator

Mode

Exec > Global Configuration > SS7 Routing Domain Configuration > Linkset Configuration

configure > ss7-routing-domain domain_id variant var_type > linkset id linkset_id

Entering the above command sequence results in the following prompt:

[local]host_name(config-ss7-rd-linkset-linkset_id)#

Syntax

Syntax Description

self-point-code point-code
no self-point-code

point-code

Point-code is an SS7 address for an element in the SS7 network. Point-codes must be defined in dotted-decimal format in a string of 1 to 11 digits. Format options include:

0.0.1 to 7.255.7 for point-code in the ITU range.
0.0.1 to 255.255.255 for point-code in the ANSI range.
0.0.1 to 15.31.255 for point-code in the TTC range.
a string of 1 to 11 digits in dotted-decimal to represent a point-code in a different range.