Log Messages
Available Languages
Table Of Contents
Log Messages
This chapter provides an overview of the Cisco Media Gateway Controller (MGC) software log message system, describes the messages and parameters that might be displayed, and lists the Media Gateway Control Protocol (MGCP) return codes that might be included in a log message.
Within this chapter, the log messages have been divided into two categories: those that provide information useful for end-users and those that provide troubleshooting information useful only to the Cisco TAC.
The following sections are included in this chapter:
For further information about configuring and using system logs, refer to the Cisco Media Gateway Controller Software Release 7 Operations, Maintenance, and Troubleshooting Guide and the Cisco Media Gateway Controller Software Release 7 MML Command Reference Guide.
Log Messages Overview
The Cisco MGC creates system log messages and stores them in log files in either the /opt/CiscoMGC/var/log directory or a directory determined during the client initialization period or specified in the XE configuration parameter file. System log messages provide vital information that you can use in monitoring your system and troubleshooting problems. However, you should observe the following caution.
CautionDebug level logging provides extremely verbose output and, if misused, can cause serious system performance degradation.
The logging subsystem takes messages initiated by various software processes within the Cisco MGC software, formats the messages, and writes them to the appropriate log files. The logging subsystem also adds a time stamp, a process identifier (for the UNIX process), and a log message severity. Refer to the "SET-LOG" section of the Cisco Media Gateway Controller Software Release 7 MML Command Reference Guide for a description of log levels.
Log messages take the following form:
Date/time-stamp, Process Name, Process ID, <log level>, LogID:<text of the message>. (This text can take multiple lines but normally is only a single line.)Example:Fri Jan 14 08:46:53:700 2000 | ProcessManager (PID 19593) <Info>GEN_INFO_PSTART: Starting process PROVSAGT.
Note
The log files are stored in a directory indicated by the *.logDirectory XE configuration parameter and are given a name indicated by the *.logFileNamePrefix XE Configuration parameter. By default, all messages are written to the platform.log file in the $BASEDIR/var/log directory.
Additional XE configuration parameters can be set to direct various log messages to log files other than platform.log. To direct all log messages from a given process to a dedicated log file, use the *.logFileNamePrefix parameter to override the default. To direct log messages by category, set the various logger.category XE configuration parameters to the desired file name.
The viewer toolkit includes a log viewer that you can use to view the contents of the system logs. Various filter criteria are provided to reduce the volume of data included for you to review when searching the logs.
MGCP Return Codes
All MGCP commands are acknowledged by the system. The acknowledgment carries a return code indicating the status of the command. A number of log messages also include the MGCP return codes. A return code is an integer, for which the following three ranges of values have been defined:
•
•
•
The values currently defined are listed in Table 2-1.
End User Log Messages
Log messages that provide information useful for end-users are presented in this section. The documentation of these messages is still incomplete. Messages that are for informational purposes only, in which the second part of the message name is _INFO_, may lack descriptions.
MESSAGE:
CP_ERR_BC_INSV: <either class::method: or class::method: call <callid>> Bear channel is not in service
DESCRIPTION:
The bearer channel is not in service state.
MESSAGE:
CP_ERR_BLK_CICS: <class::method>: failed to block > <number of cics> cics
DESCRIPTION:
The action to block the CIC has failed because the CIC number is larger than the maximum number of CICs.
MESSAGE:
CP_ERR_CRT_PTCODE: <class::method>: unable to associate SS7 service <SS7 Service> to destination point code address
DESCRIPTION:
The request to create the SS7 service failed because there is no entry in the destination point code address table.
MESSAGE:
CP_ERR_FIND_COMPTYPE: <class::method>: failed to find compType table entry <component type>
DESCRIPTION:
The component type is not found in the component table.
MESSAGE:
CP_ERR_FIND_CUST: <class::method>: failed to find customer <customer ID>
DESCRIPTION:
The specified customer is not found.
MESSAGE:
CP_ERR_FIND_PTCODE: <class::method: <call<callid>>>: cannot find pointCode <point code>
DESCRIPTION:
The point code cannot be found.
MESSAGE:
CP_ERR_FIND_SIGPATH_COMP: <class method>: failed to find sigPath <sigPath Id> in component table
DESCRIPTION:
The signaling path cannot be found in the component table.
MESSAGE:
CP_ERR_FIND_SPAN: <class::method>: failed to find span <sigPath>/<span>
DESCRIPTION:
The span cannot be found in the span table.
MESSAGE:
CP_ERR_FIND_TRUNK: <class::method>: failed to find trunk <trunkGroup>/<trunk>
DESCRIPTION:
The trunk cannot be found in the trunk table.
MESSAGE:
CP_ERR_FIND_TRUNKGRP: <class::method>: failed to find trunkGroup <trunkGroup ID>
DESCRIPTION:
The trunk group cannot be found in the component table.
MESSAGE:
CP_ERR_FIND_TRUNKGRP_FOR_SIGPATH: <class::method: <call<callid>>>: cannot find trunkGroup for sigPath <sigPath Id> bearChan <bearChan id>
DESCRIPTION:
The trunk group cannot be found for the signal path or bearer channel.
MESSAGE:
CP_ERR_FIND_VP1: <class::method>: failed to find VP <VP ID>
DESCRIPTION:
The virtual path cannot be found.
MESSAGE:
CP_ERR_FIND_VP2: <class::method>: failed to find VP between VSF <VSF ID> - <VSF ID>
DESCRIPTION:
The virtual path cannot be found in the specified range of virtual switching fibers.
MESSAGE:
CP_ERR_FIND_VSF: <class::method>: failed to find VSF <VSF ID>
DESCRIPTION:
The virtual switching fiber cannot be found.
MESSAGE:
CP_ERR_FIND_VSF_BOX: <class::method>: failed to find VSF with boxnum <VSF box number>
DESCRIPTION:
The virtual switching fibers with the box number cannot be found.
MESSAGE:
CP_ERR_FIND_VSF_CXNSP: <class::method>: failed to find VSF with cxnSigPath <sigPath ID>
DESCRIPTION:
The virtual switching fiber with the connection signal path cannot be found.
MESSAGE:
CP_ERR_HUNG_CXN: <class::method>: bearChan <bearChan ID> hung on VSF <VSF ID>
DESCRIPTION:
This bearer channel is still set as in use on the VSF, but the call that created the connection has ended.
MESSAGE:
CP_ERR_HW_BC_BLK: <either class::method: or class::method: call <callid>> Bear channel is hardware blocked
DESCRIPTION:
The bearer channel is in the state of hardware blocking.
MESSAGE:
CP_ERR_INV_USER: <class::method>: invalid user/network for sigPath <sigPath ID>, default=user
DESCRIPTION:
The user or network for the signal path is invalid; the default is changed.
MESSAGE:
CP_ERR_LOAD_COT: <class::method>: failed to load <COT percentage name>, must be 0-100
DESCRIPTION:
The action to load the continuity test percentage has failed; the percentage must be between 0 and 100.
MESSAGE:
CP_ERR_MAN_BC_BLK: <either class::method: or class::method: call <callid>> Bear channel is manual blocked
DESCRIPTION:
The bearer channel is manually blocked.
MESSAGE:
CP_ERR_NO_AVAIL_BC: <either class::method: or class::method: call <callid>> No available bear channel
DESCRIPTION:
There is no available bearer channel to be acquired for new calls.
MESSAGE:
CP_ERR_RESET_ACT: <class::method>: failed to reset, grp reset already active on <pointCode>/<CIC>x
DESCRIPTION:
The reset action has failed because the group reset action was already activated on the point code.
MESSAGE:
CP_ERR_RESET_BC: <class::method>: failed to reset bearChan, no call on <pointCode>/<CIC>
DESCRIPTION:
The action to reset the bearer channel has failed because there is no call on the channel.
MESSAGE:
CP_ERR_RESET_CICS: <class::method>: failed to reset > <max number of cics> cics
DESCRIPTION:
The action to reset the CIC has failed because the CIC number is larger than the maximum CIC number.
MESSAGE:
CP_ERR_SP_IS_CONG: <either class::method: or class::method: call <callid>>: SigPath is congested
DESCRIPTION:
The signal path is in congestion. The new call setup may be affected.
MESSAGE:
CP_ERR_START_AUDIT: <either class::method: or class::method: call <callid>>: Cannot start audit
DESCRIPTION:
Unable to start a NAS audit; cannot start the audit timer
MESSAGE:
CP_ERR_START_GWAY_AUDIT: <either class::method: or class::method: call <callid>> Failed to start GWAY audit
DESCRIPTION:
Produced during startup and at failover (standby to active) to warn the user that a gateway audit has not been performed, typically as a result of XECfgParm.dat parameter engine.StarUpAuditEnabled=false. This message does not generally indicate a problem.
MESSAGE:
CP_ERR_STOP_GWAY_AUDIT: <either class::method: or class::method: call <callid>> Failed to stop GWAY audit during platform state change
DESCRIPTION:
The action to stop the gateway audit has failed because the platform state change is processing.
MESSAGE:
CP_INFO_DEL_DP: failed to delete dial plan tbls for customer <customer ID>, sigPath <sigPath ID>
MESSAGE:
CP_INFO_LOAD_DIALPLAN_FAIL: failed to load dial plan tbls for customer <customer ID>
MESSAGE:
CP_INFO_LOAD_DIALPLAN_OK: loaded dial plan tbls for customer <customer ID>
MESSAGE:
CP_WARN_CALL_FAIL: <class::method> <compID of either orig or term sigPath> <Span and CIC information>s
DESCRIPTION:
Produced any time a call object cannot be fully instantiated because the "mated" B channel(s) are unavailable for the reason shown in the log message:
•
•
Note
MESSAGE:
CP_WARN_CANT_IDLE: Audit cannot make vsf idle for pc <sigPathID>, span <spanID>, CIC <circuitID>
DESCRIPTION:
The audit cannot bring the virtual switching fiber to idle state.
MESSAGE:
CP_WARN_CONFIG_ERRS: <class::method>: <number of errors> config errors
DESCRIPTION:
Indicates a nonexistent signal path or the signal path has no bearer channels. The number of errors indicates the number of configuration violations detected.
MESSAGE:
CP_WARN_DUP_CHPT_MSG: <class::method>: Duplicate checkpoint answer message for call <call id
DESCRIPTION:
During an attempt to create a standby call, it was noted that the checkpoint answer message already exists. Duplicate call is not created.
MESSAGE:
CP_WARN_INV_CONFIG: <class::method>: invalid config, only <num bearChans> bearChans
DESCRIPTION:
The configuration command is invalid because the bearer channel number is less than 2.
MESSAGE:
CP_WARN_PTCODE_SEND_BLK1: bearChan: <pointCode>/<CIC> failed to send un/block msgs, pointCode not IS or initialized
DESCRIPTION:
Failed to send BLOCK/UNBLOCK messages; the point code is not in service state or is not initialized.
MESSAGE:
CP_WARN_PTCODE_SEND_BLK2: failed to send un/block msgs, pointCode <pointCode ID> not IS
DESCRIPTION:
Failed to send BLOCK/UNBLOCK messages; the point code is not in the service state.
MESSAGE:
CP_WARN_UCIC: <class method>: received unequipped CIC <CIC> for point code <point code>
DESCRIPTION:
Configuration error; bearer channel for originating call is not found.
MESSAGE:
ENV_CRIT_PROC_ERR: Unexpected return from <`Pre-init'|`init'|`Post-init'|`Run'|`Pre-finalize'> stage, status = <XE Status code - reason for the failure> (<status code converted to an error message string>)
DESCRIPTION:
Process initialization failure message in the XEProcShell. This can be either Finalize or Post-finalize.
MESSAGE:
ENV_ERR_CONFIG_PARM_LOOKUP_FAIL: Configuration parameter lookup failed for <Execution Environment Configuration Parameter name>
DESCRIPTION:
Process failed to locate the given parameter in the execution environment configuration file; the process will exit.
MESSAGE:
ENV_ERR_DEFLT_CHDIR: Change to default data dir <Default data directory> failed: <Error code> (<Error code converted to a string>)
DESCRIPTION:
The data directory is missing or the user does not have permission to access it.
MESSAGE:
ENV_ERR_GETHOSTBYNAME: Failed to find hostname for IPC <Pathname>, status <Error code>
DESCRIPTION:
The host in question does not exist or is currently not connected to the network.
MESSAGE:
ENV_ERR_PLATFORM_ID: Invalid value for PlatformId = <Bad platform id string from config parameter file>. Check configuration parameters.
DESCRIPTION:
Invalid information in the configuration file for the PlatformId.
MESSAGE:
ENV_ERR_PROCESSOR_INFO: Failed to get processor info - Status: <Error code>
DESCRIPTION:
The system will not attempt to bind engine threads to specific CPUs. The system will run, but performance might suffer if the CPU binding is required for this configuration to run at peak efficiency.
MESSAGE:
ENV_INFO_BIND_PROCESSOR_OK: Bind to processor <Processor number> successful
MESSAGE:
ENV_INFO_BIND_PSET: Attempt to bind to processor set <Processor set>
MESSAGE:
ENV_INFO_BIND_PSET_OK: Bind to processor set <Processor set> successful
MESSAGE:
ENV_INFO_BIND_THREAD: Bind Component <Component Id> to Thread - Poolname = <Thread identifier in SW_Layout table>
MESSAGE:
ENV_INFO_CLR_ALARM: COMPID <Component Id>: Clear alarm - Category <Category Id> Desc: <Alarm Description>
DESCRIPTION:
Clear a specific alarm.
MESSAGE:
ENV_INFO_CPU: Physical System: <Host name>\n\t# CPU = <Number of CPUs>\n\tClock Speed = <CPU Clock Speed>
MESSAGE:
ENV_INFO_IPC_OPEN: Opened FIFO <Name of the FIFO>(fd = <File Descriptor>)
MESSAGE:
ENV_INFO_NO_COMP_ENTRY: Failed to find component entry for <Component id> - Err = <Error code from findObj routine>
MESSAGE:
ENV_INFO_PROCESSOR_INFO: Failed to get processor info - status = <Error code>
DESCRIPTION:
The system will not attempt to bind engine threads to specific CPUs. The system will run, but performance might suffer if the CPU binding is required for this configuration to run at peak efficiency.
MESSAGE:
ENV_INFO_SET_ALARM: COMPID <Component Id>: Set alarm - Category <Alarm Category> Desc: <Alarm Description>
DESCRIPTION:
Set a specific alarm.
MESSAGE:
ENV_INFO_SET_PROCESS_PRIORITY: Attempt to set process priority to <New process priority>
MESSAGE:
ENV_INFO_SET_SCHED_PARMS: Scheduling parameters set successfully
MESSAGE:
ENV_WARN_CONFIG_PARM_LOAD_FAIL: <Handler trying to load a parameter>: Config param load failed for <Parameter name>, using default value (<Default value (may be empty string)>)
DESCRIPTION:
The system attempted to load a config parameter from the configuration file and failed; the system will continue with the default value for this parameter.
MESSAGE:
ENV_WARN_GET_SCHED_PARMS_FAIL: Can't get scheduling parameters - Errno = <Unix Error code>
DESCRIPTION:
Unable to get scheduling parameters.
MESSAGE:
ENV_WARN_LOAD_TBL: Failed to load component table with data mgr (<Error return from load routine>)
DESCRIPTION:
Failed to load a data table.
MESSAGE:
ENV_WARN_MEAS_LOCKFAIL: XEMeas(<Component Id>, <Category Id>): Failed to lock shared mem - Error code=<Error code>
DESCRIPTION:
Trying to update a shared memory measurement and failed to acquire the lock. See /usr/include/sys/errno.h for an interpretation of the error code.
MESSAGE:
ENV_WARN_SET_SCHED_PARMS_FAIL: Can't set scheduling parameters - Errno = <Unix Error code>
DESCRIPTION:
Failed to set scheduling parameters.
MESSAGE:
GEN_CRIT_AB_SWITCH_INIT_FAIL: <Classmethod> Error initializing A/B switch, switchover failed - will retry every <period in seconds, after which a retry will be attempted> seconds
DESCRIPTION:
During a failover attempt, the A/B switch could not be initialized. Re-attempt to initialize periodically based upon the value in foverd.commRetryInterval (milliseconds) in the XECfgParm.dat file.
MESSAGE:
GEN_CRIT_DYN_RCONFIG_BK_FAIL: Back-out of dynamic re-config failed <further info or an empty string>.
DESCRIPTION:
After failure of dynamic reconfiguration, a roll-back to the previous configuration was attempted. This roll-back failed. The Cisco MGC will continue to use available configuration information.
MESSAGE:
GEN_CRIT_FOD_REQ_PARMS: Required parms <loaded | missing> : <info on the params or null string>
DESCRIPTION:
Unable to load required parameters from the XECfgParm.dat file.
MESSAGE:
GEN_CRIT_OBJ_LNK_ERR: Error re-linking object model <further info or an empty string>
DESCRIPTION:
Dynamic reconfiguration has failed. Roll-back to original configuration will be attempted.
MESSAGE:
GEN_CRIT_PINIT: <class::method>: Process <process name> initialization failed. <specific reason for failure>
DESCRIPTION:
Unable to initialize a specified process. The reason for the failure is given.
MESSAGE:
GEN_ERR_AB_SWITCH_MODE_SET_FAIL: Cannot set <name of the mode> mode (errno: <error no>), will retry every <period in seconds, after which a retry will be attempted> seconds
DESCRIPTION:
The failover daemon is unable to set the mode of the A/B switch while initializing the A/B switch (during switchover). Re-attempt to set the mode periodically, based upon the value of foverd.commRetryInterval (milliseconds) in the XECfgParm.dat file.
MESSAGE:
GEN_ERR_AB_SWITCH_OPEN_FAIL: Cannot open <name of the device (path) to which the A/B switch is connected> (errno: <error no>), will retry every <period in seconds, after which a retry will be attempted> seconds
DESCRIPTION:
During a failover attempt, unable to open a port on the A/B switch. Re-attempt to open periodically based upon the value of foverd.commRetryInterval (milliseconds) in the XECfgParm.dat file.
MESSAGE:
GEN_ERR_AB_SWITCH_SIG_FAIL: Could not set <<signal name> (RTS,DTR etc.)> on <name of the device (path) to which the AB Switch is connected (errno: <errno>)
DESCRIPTION:
During a failover attempt, unable to send a sequence of pulses controlling the A/B switch. Re-attempt to initialize periodically based upon the value of foverd.commRetryInterval (milliseconds) in the XECfgParm.dat file.
MESSAGE:
GEN_ERR_CONFIG_FAIL: compId <component id>: <process and action> Configuration failure <reason>
DESCRIPTION:
An attribute of the specified component was configured with an invalid value.
MESSAGE:
GEN_ERR_DIROPEN: <class::method>: Error opening directory <name of directory which could not be opened>, status = <status of open operation>
DESCRIPTION:
Unable to create the specified directory. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
23 = File table overflow
24 = Too many open files
25 = Inappropriate ioctl for device
28 = No space left on device
MESSAGE:
GEN_ERR_FCOPY: Error copying file <name of file being copied> to <name of file being copied to, status = <status of copy>
DESCRIPTION:
Unable to copy the specified file. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
23 = File table overflow
24 = Too many open files
25 = Inappropriate ioctl for device
26 = Text file busy
27 = File too large
28 = No space left on device
MESSAGE:
GEN_ERR_FLINK: Error creating link between <top level directory> - <active directory path>, status = <System error code>
DESCRIPTION:
Unable to create an active link between directories. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
25 = Inappropriate ioctl for device
26 = Text file busy
29 = Illegal seek
30 = Read only file system
31 = Too many links
32 = Broken pipe
MESSAGE:
GEN_ERR_FNOTFOUND: Could not find file <file which could not be found>.
DESCRIPTION:
Unable to find the specified file. Possible status meanings are:
2 = No such file or directory
9 = Bad file number
20 = Not a directory
MESSAGE:
GEN_ERR_FOD_CXN_INIT_FAIL: Cannot initialize connection <connection Id (errno: <error no>) will retry every <period in seconds, after which a retry will be attempted> seconds
DESCRIPTION:
Unable to open the serial connection between the peer failover daemons. The Cisco MGC will attempt to open this connection again based upon the parameter in XECfgParm.dat forverd.commRetryInterval (in milliseconds). The default retry in the XECfgParm.dat file is 30 seconds (300 milliseconds).
MESSAGE:
GEN_ERR_FOPEN: Error opening file <name of file/fifo>, status = <status of open operation>
DESCRIPTION:
Unable to create or write to the specified file. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
23 = File table overflow
24 = Too many open files
25 = Inappropriate ioctl for device
26 = Text file busy
27 = File too large
28 = No space left on device
MESSAGE:
GEN_ERR_FREAD: Error reading file <name of file/fifo>, status = <status of read operation>
DESCRIPTION:
Unable to read the specified file. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
26 = Text file busy
27 = File too large
MESSAGE:
GEN_ERR_FREMOVE: Error removing file <file name>, status = <status>
DESCRIPTION:
Unable to delete the specified file. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
26 = Text file busy
MESSAGE:
GEN_ERR_FRENAME: Error renaming file <current file name> to be <new file name>, status = <status>
DESCRIPTION:
Unable to rename the specified file. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
25 = Inappropriate ioctl for device
26 = Text file busy
MESSAGE:
GEN_ERR_FWRITE: Error writing file <name of file>, status = <status>
DESCRIPTION:
Unable to create or write to the specified file. Possible status meanings are:
1 = Not super-user
2 = No such file or directory
9 = Bad file number
20 = Not a directory
23 = File table overflow
24 = Too many open files
25 = Inappropriate ioctl for device
26 = Text file busy
27 = File too large
28 = No space left on device
MESSAGE:
GEN_ERR_GETCFGPARM: <class::method>: Failed to get <name of configuration parameter> for facility <name of the facility>
DESCRIPTION:
Could not obtain the desired parameter from the XECfgParm.dat file.
MESSAGE:
GEN_ERR_HA_MSO: Cannot comply with Manual Switch Over request. Reason <reason string>
DESCRIPTION:
A request for manual switchover cannot be complied with.
MESSAGE:
GEN_ERR_HA_RSP: Received a NAK for Platform State from <component name>
DESCRIPTION:
A component fails to respond favorably to an HA command.
MESSAGE:
GEN_ERR_HLTH_ALM_CAT_FAIL: Health alarm category <name of the health alarm category> not found in table <table name>
DESCRIPTION:
An alarm category was not found in the appropriate configuration table.
MESSAGE:
GEN_ERR_LINK_DOWN: Link to <Remote location> is down
DESCRIPTION:
The communication path is unavailable.
MESSAGE:
GEN_ERR_MISMATCH: protocol mismatch with <name of the module, compID of link, compID of channel controller>
DESCRIPTION:
The protocol family for the link does not match that of the assigned channel controller.
MESSAGE:
GEN_ERR_MISSING: <What is missing - for example, in XEAlmCat.cpp it is `SNMP Trap #'> is missing for <Name of object that is missing information>
DESCRIPTION:
General error; a parameter or object is missing configuration or update information.
MESSAGE:
GEN_ERR_MKDIR: Failed to create directory: <Pathname>
DESCRIPTION:
Failed to create a directory; the path may be invalid or the user may not have permission to create a directory.
MESSAGE:
GEN_ERR_NOROUTE: compId <Component Id>: No Route found for <name (example: channel controller)>
DESCRIPTION:
Unable to get SS7 route information from data dictionary for the specified SS7 channel controller.
MESSAGE:
GEN_ERR_PG_NOT_FOUND: Process group name <process group name> not found in table <table name>
DESCRIPTION:
Did not find the specified process group in the components.dat file.
MESSAGE:
GEN_ERR_PROC_INPUT: Bad input stream while initializing process <process name>
DESCRIPTION:
The data dictionary file processes.dat is either missing or corrupted, or the specified process is not described in the processes.dat file.
MESSAGE:
GEN_ERR_PROC_KILL_FAIL: <name of process> Failed to kill process <reason>
DESCRIPTION:
Failed to kill the specified process. The reason is given in a system error code.
MESSAGE:
GEN_ERR_PROC_NOT_FOUND: Process name <process name> not found in table <table name>
DESCRIPTION:
Did not find the specified process in the components.dat file.
MESSAGE:
GEN_ERR_PSTOP: <class::method>: Failed to stop process <name of process>. <reason>
DESCRIPTION:
Unable to stop the specified process. The reason is a system error number.
MESSAGE:
GEN_ERR_SERVICE: <class::method>: Could not find service <name of the service>
DESCRIPTION:
The data manager is unable to find the specified service in the services.dat file.
MESSAGE:
GEN_ERR_SERV_NOT_AVA: <service name> service is not available
DESCRIPTION:
The service is not available.
MESSAGE:
GEN_ERR_TIMEOUT: <class::method name>: <timer name or other description of timer> timeout
DESCRIPTION:
The process timed-out while waiting for a response from the client or user.
MESSAGE:
GEN_ERR_TIMEOUT_PROC: <classmethod name> <timer name or other description of timer> timeout for <process name> process.
DESCRIPTION:
The response expected from the specified process did not occur within the time period set by the specified timer.
MESSAGE:
GEN_ERR_XFER_FILE: <class::method>: file transfer failed for <name of file being transferred>, status = <status>
DESCRIPTION:
Unable to move a file from one directory to another. The status is an XE event code.
MESSAGE:
GEN_INFO_ADDPATH_REQ: compId <component id>:Request to add path
MESSAGE:
GEN_INFO_CHG_PLAT_STATE: Setting the platform state to <target platform state>
DESCRIPTION:
Setting the platform to the specified state.
MESSAGE:
GEN_INFO_CHG_PROC_STATE: Changing the current state <current state> of Process <Process name> to <new state>
DESCRIPTION:
Changing the current state of the specified process to the new state.
MESSAGE:
GEN_INFO_CHKSUM: CheckSum on File <Filename> = <String containing the checksum value>
MESSAGE:
GEN_INFO_COMP_MON_STOP: Stopping monitoring for component <component name>
MESSAGE:
GEN_INFO_COMP_MON_STRT: Starting monitoring for component <component name>
MESSAGE:
GEN_INFO_COMP_MON_STRT_ACT: Graceful startup for monitoring of component <component name> pending active dependencies <description of active dependencies>
MESSAGE:
GEN_INFO_COMP_MON_STRT_INACT: Graceful startup for monitoring of component <component name> pending inactive dependencies <description of inactive dependencies>
MESSAGE:
GEN_INFO_DYN_RCONFIG_BK_OK: Back-out of dynamic re-config successful
MESSAGE:
GEN_INFO_DYN_RCONFIG_COMP: Dynamic re-configuration completed
MESSAGE:
GEN_INFO_DYRFG_STRT: Beginning dynamic re-configuration
MESSAGE:
GEN_INFO_EVTEXIT: Exiting event handler <name of event handler>
MESSAGE:
GEN_INFO_EVTHDNL_NOT_RQD: <Eventhandler name> Need not handle event of type <event type> <further info or an empty string>
MESSAGE:
GEN_INFO_EVTINIT: Initializing event handler <name of event handler>
MESSAGE:
GEN_INFO_EVT_CRT: Creating event <name of the event>
MESSAGE:
GEN_INFO_FACSTRT: Request to start <Facility name> completed with status <Return status or further info or an empty string>
MESSAGE:
GEN_INFO_FCREATE: Creating file <name of the file>
MESSAGE:
GEN_INFO_FIND_DIR: Failed to find directory: <Pathname>
MESSAGE:
GEN_INFO_FOD_RQ_RCV: Failover daemon received <type of request received <shutdown, OOS,IS etc.)> request <current state of local system> <current state of remote system>
MESSAGE:
GEN_INFO_FOVERD: <info string>
DESCRIPTION:
Generated by foverd to reflect the pertinent fault tolerant information.
MESSAGE:
GEN_INFO_FREAD: Reading file <name of the file>
MESSAGE:
GEN_INFO_GETCFGPARM: Getting Configuration Parameter <value of cfg. parameter> of <name of the parameter>, Facility <name of the facility>
MESSAGE:
GEN_INFO_HA_ACTION: <name of the process>: handling HA command <HA command <Standby/OOS/FSO/CSO>> <node for which this command is intended <local/remote>>
DESCRIPTION:
This message is used by components that receive an HA command from the process manager. When the process manager propagates High Availability commands to transition the platform to a certain active or standby state, these commands are received by different components like the Alarm Manager, Engine, Replicator, IOCM, and others. This message is intended for use by these components when handling such commands.
MESSAGE:
GEN_INFO_HA_ALL_READY: FT all ready
MESSAGE:
GEN_INFO_HA_ID: FTHA ownId=compId <component id>: peerid=<component id of peer>
MESSAGE:
GEN_INFO_HA_MSO_ENT: Entertaining a request for Manual Switch Over
MESSAGE:
GEN_INFO_HA_READY: <IOCC id of relevant IO Channel Controller>: FT Ready
MESSAGE:
GEN_INFO_HA_REG: <IOCC id of relevant IO Channel Controller>: FT Registered
MESSAGE:
GEN_INFO_HA_RSP: Received an Acknowledgement for Platform state from <component name>
DESCRIPTION:
This is an informational message logged by the process manager when a component responds favorably to an HA command.
MESSAGE:
GEN_INFO_IGNORE: Ignoring <Explanatory text>
MESSAGE:
GEN_INFO_INVALID_CONFIG: Unexpected configuration
MESSAGE:
GEN_INFO_LOG_LVL_CHGFAIL: <name of handler> Request for log level change, Component ID <ComponentId> failed <further info or an empty string>
MESSAGE:
GEN_INFO_MAXLINES: compId <Component Id>: Max <example: SRCP> number of lines exceeded
MESSAGE:
GEN_INFO_MONP_VERSION_CRT: Version <version> of monitoring process <process name> created
MESSAGE:
GEN_INFO_MON_PROC_CRT: Created monitoring process <process name>
MESSAGE:
GEN_INFO_MON_PROC_DEL: Monitoring process <process name> deleted
MESSAGE:
GEN_INFO_MON_PROC_SRSTRT: Monitoring process <process name> stop detected, with signal number <signal no.>, killing and restarting
MESSAGE:
GEN_INFO_MON_PROC_TRSTRT: Monitoring process <process name> termination detected, with signal number <signal no.>, restarting
MESSAGE:
GEN_INFO_MON_PROC_VERSION_SUP: Version <version> of monitoring process <process name> superseded
MESSAGE:
GEN_INFO_OLD_MON_PROC_COMP_KILL: Killed old monitoring process for component <component name>
MESSAGE:
GEN_INFO_OLD_MON_PROC_KILL: Killed old monitoring process for component <process name>
MESSAGE:
GEN_INFO_PCREAT: Created process <process name> with PID <process ID>
MESSAGE:
GEN_INFO_PDEL: Process <process name> deleted
MESSAGE:
GEN_INFO_PEXIT: Process <process which is exiting> exiting
DESCRIPTION:
This message is used by the process that is exiting.
MESSAGE:
GEN_INFO_PG_ACTION: <Activity indication <startup/shutdown>*> for process group <process group name> pending <description of the pending dependents <active/inactive>*> dependents
MESSAGE:
GEN_INFO_PG_BEGIN: Beginning graceful <state indication <Startup/Shutdown>> for process group <process group name>
MESSAGE:
GEN_INFO_PG_DELETED: Process group <process group name> deleted
MESSAGE:
GEN_INFO_PG_FEXIT: Force exiting process group <process group name>
MESSAGE:
GEN_INFO_PG_SDL_START: Scheduling startup for process group <process group name> in <seconds before startup> seconds
MESSAGE:
GEN_INFO_PG_SHUTDOWN: Shutting down process group <process group name>
MESSAGE:
GEN_INFO_PG_START: Starting process group <process group name>
MESSAGE:
GEN_INFO_PG_SUPERSEDED: Process group <process group name> superseded
MESSAGE:
GEN_INFO_PINIT: Process <process name> initialization complete
DESCRIPTION:
Initialization complete message.
MESSAGE:
GEN_INFO_PRG_OBSLT_DAT: Purging obsolete data from memory
MESSAGE:
GEN_INFO_PROCM: <Process Manager Informational Message>
DESCRIPTION:
Process manager informational message.
MESSAGE:
GEN_INFO_PROCM_FOD_MSG: Received command <command name> from FailOver process for node <node> in <Current state of the node> state
DESCRIPTION:
Received the specified command from the failover process for the specified node.
MESSAGE:
GEN_INFO_PROCM_RECVD_RES: Received <Response type> response from process <Process name>
DESCRIPTION:
The process manager received the specified response from the process stated.
MESSAGE:
GEN_INFO_PROC_NOTACTIVE: Process <process name> NOT Active
MESSAGE:
GEN_INFO_PROC_PND_SHUT_INACT: Shutdown for process <process name> pending active dependencies <description of active dependencies>
MESSAGE:
GEN_INFO_PROC_PND_START_INACT: Startup for process <process name> pending inactive dependencies <description of inactive dependencies>
MESSAGE:
GEN_INFO_PROC_RECOV: Process <Process name> has not recovered. <Extra information>
DESCRIPTION:
The specified process has not recovered. Additional information is given
MESSAGE:
GEN_INFO_PROC_RESTRT_DENY: Process <process name> has exceeded its restart limit of <maxRestarts> within <interval> seconds and will not be scheduled for restart
MESSAGE:
GEN_INFO_PROC_RESTRT_INIT: Restart initiated for process <process name>
MESSAGE:
GEN_INFO_PROC_RESTRT_STAT: Process <process name> restart <info on restart - already scheduled to restart, will not be scheduled to restart>
MESSAGE:
GEN_INFO_PROC_SDL_RESTRT: Scheduling startup for process <process name> in <time interval in seconds within which startup is scheduled> seconds
MESSAGE:
GEN_INFO_PROC_SDL_START: Scheduling startup for process <process name> in <seconds before startup> seconds
MESSAGE:
GEN_INFO_PROC_STAT_REQ_FAIL: <name of handler> Request for process status, Component ID <ComponentId> failed <further info or an empty string>
MESSAGE:
GEN_INFO_PROC_STOP_DETECTED: Process <process name> stop detected, with <additional info (`exit status' or `signal no')> <value of exit status or signal no>
MESSAGE:
GEN_INFO_PSHUT: Shutting down process <Process name> <further info or an empty string>
MESSAGE:
GEN_INFO_PSTART: Starting process <name of process that was started>
DESCRIPTION:
This message is used by the process that starts another process.
MESSAGE:
GEN_INFO_PSTARTED: Process <name of process that was started> started
DESCRIPTION:
This message is used by the process that was started by another process.
MESSAGE:
GEN_INFO_PVERSION_CRT: Version <version> of process <process name> created
MESSAGE:
GEN_INFO_PVERSION_SUP: Version <version> of process <process name> superseded
MESSAGE:
GEN_INFO_RECOV_COMP: Recovery for platform <PlatformId> completed <further info or an empty string>
MESSAGE:
GEN_INFO_RECOV_INIT: Initiating recovery sequence for platform <PlatformId> <further info or an empty string>
MESSAGE:
GEN_INFO_SHUT_COMP: Shutdown for platform <PlatformId> completed <further info or an empty string>
MESSAGE:
GEN_INFO_SHUT_INIT: Initiating shut-down sequence for platform <PlatformId> <further info or an empty string>
MESSAGE:
GEN_INFO_STANDALONE: Detected Standalone flag. Declaring the platform to be Active
MESSAGE:
GEN_INFO_STRT_INIT: Initiating start-up sequence for platform <PlatformId> <further info or an empty string>
MESSAGE:
GEN_INFO_TIMEOUT: <Name of the timer> timeout. <further info or an empty string>
MESSAGE:
GEN_INFO_VERSION: Process <process ID> - Version <version>
MESSAGE:
GEN_TRACE_EVTREC: <name of the event handler> Received message with event type/subtype <event type>/<event subtype>
MESSAGE:
GEN_TRACE_FREAD: Reading <FIFO name>, status = <status of read operation>, size = <number of bytes read>
DESCRIPTION:
Shows the status of reading a FIFO.
MESSAGE:
GEN_TRACE_FWRITE: Writing <FIFO name>, status = <status of read operation>, size = <number of bytes written>
DESCRIPTION:
Shows the status of writing a FIFO.
MESSAGE:
GEN_TRACE_IPCREAD: <class::method name>: Reading IPC <IPC name or service name>, size = <size of the data read from this IPC>
MESSAGE:
GEN_TRACE_POLLEVTREC: <class::method name>: received polling event <event type>
MESSAGE:
GEN_WARN_DEL: compId <component id> :Deleting component
DESCRIPTION:
Deleting the specified link from the channel controller.
MESSAGE:
GEN_WARN_FOD_PARM_INV: Invalid <parameter name> using default: <default value>
DESCRIPTION:
Did not obtain a meaningful value for this parameter from the XECfgParm.dat file. Using the default parameter. Default parameters are:
•
•
•
•
•
•
•
•
•
MESSAGE:
GEN_WARN_FOD_REM_STATE_CHG: Remote system <current/failover> state change: <current state> --> <next state>
DESCRIPTION:
The failover daemon is unable to change the state (to either current or failover) of the remote system.
MESSAGE:
GEN_WARN_FOVERD: <Information>
DESCRIPTION:
Reflects the pertinent fault tolerant warning information.
MESSAGE:
GEN_WARN_HA_MODE_NONHA: FT: non-fault tolerance mode going active
DESCRIPTION:
Unable to handle the platform state change. The non-fault tolerance mode is activated.
MESSAGE:
GEN_WARN_MON_PROC_TERM_TO: Monitoring process for component <component name> has not terminated within the expected health timeout interval of <timeout value> seconds, suspending monitoring until it terminates
DESCRIPTION:
The monitoring process for the specified component did not terminate within the expected health timeout interval; suspending monitoring until it terminates.
MESSAGE:
GEN_WARN_PATH_NOT_CREATED: compId <component id> :Path could not be created
DESCRIPTION:
An SS7 route could not be created for the specified component.
MESSAGE:
GEN_WARN_PHEALTH_CHK: Process <process name> failed health check
DESCRIPTION:
The specified process failed to respond to the heartbeat and is apparently not alive.
MESSAGE:
GEN_WARN_PROCM_ACKWAIT: Process <Process name> has not acknowledged command <command>
DESCRIPTION:
The specified process has not acknowledged the command sent.
MESSAGE:
GEN_WARN_PROCM_FOD_NAK: Failover process not starting predictably
DESCRIPTION:
The failover daemon has sent a negative acknowledgment.
MESSAGE:
GEN_WARN_PROCM_MSGIGN: Ignoring the message <message> from <node (local/remote)> . Reason: <Reason>
DESCRIPTION:
A message sent from either the local or remote node is being ignored for the reason stated.
MESSAGE:
GEN_WARN_PROCM_NOACK: No acknowledgement received from process <Process Name> for command <command>
DESCRIPTION:
Received an acknowledgment from the specified process for the command that was sent.
MESSAGE:
GEN_WARN_PROCM_OOS_FOD: Sending an Out Of Service Command to the FailOver process
DESCRIPTION:
Sending an out of service command to the failover process.
MESSAGE:
GEN_WARN_PROCM_PEND_COM: <Last Command> command pending. Received new command <New Command> from Failover Process
DESCRIPTION:
Received a new command from the failover process. The old command is still pending.
MESSAGE:
GEN_WARN_PROC_NOT_ALIVE: Process with PID <PID> is not alive, but is still listed in active process table
DESCRIPTION:
During a periodic cleanup by the process manager, it was discovered that the specified process identified by the PID is no longer alive.
MESSAGE:
GEN_WARN_PROC_TERM_DETECTED: Process <process name> termination detected, with <additional info (`exit status' or `signal no')> <value of exit status or signal no>
DESCRIPTION:
Termination of the specified process has been detected. The value of the exit status is a system wait code (see the UNIX command waitpid).
MESSAGE:
GEN_WARN_PSHUT: Shutting down process <Process name> <further info or an empty string>
DESCRIPTION:
Indicates that a graceful shutdown of the specified process is occurring.
MESSAGE:
GEN_WARN_PSTARTED: Process <name of process that was started> started
DESCRIPTION:
This message is used by the process that was started by another process.
MESSAGE:
GEN_WARN_PSTOP: Stopping process <process stopped>
DESCRIPTION:
The process manager is stopping the specified process.
MESSAGE:
GEN_WARN_SIG: Received signal <Signal name> <further info or an empty string>
DESCRIPTION:
The process manager received the specified signal.
MESSAGE:
MGMT_ERR_MMDBALRT: MMDB ALERT: <alert string>
DESCRIPTION:
Notifies user of the fault contained in the alert message
MESSAGE:
MGMT_ERR_POM_DEPLOY: <class::method>: deploy failed, status = <status>
DESCRIPTION:
Unable to deploy the provisioned configuration. Rollback to the original configuration. Status is an XE event code.
MESSAGE:
MGMT_ERR_POM_POSTPROV: <class::method name>: Error in post provisioning processing <Provisioning error message returned>
DESCRIPTION:
Post-processing in the POL (creation of channel controllers, customer specific files) failed.
MESSAGE:
MGMT_ERR_POM_PROVVALID: <class::method name>: Error validating configuration data for <number of tables rejected> tables
DESCRIPTION:
Validation of the provisioned configuration resulted in errors. Rollback to the original configuration. Number of validation rejections is provided.
MESSAGE:
MGMT_ERR_SETALMSEV: Failed to set Alarm Severity <alarm severity level <almMinor/almMajor/almCritical>> by command <command sent to device by IOCTL (TSIOCALCTL/U4FTIOCALCTL)>, status = <status>
DESCRIPTION:
Unable to set the alarm severity for the specified alarm. The status code is a system code (identified in errno.h).
MESSAGE:
MGMT_ERR_UPDOBJ: <class::method name>: Failed to update < name of object>, status = <Provisioning Object Library (POL) error code>
DESCRIPTION:
Unable to update or edit a component in the data dictionary.
MESSAGE:
MGMT_INFO_ALMACKED: Alarm (category ID <category ID>, component ID <component ID>) is set and acked
MESSAGE:
MGMT_INFO_ALMLOG: ALARM Originator <service ID>, Category <alarm category ID>, State <alarm state>
MESSAGE:
MGMT_INFO_CHANGE_LOG_LVL: Changing logging level to <new logging level (DEBUG, INFO, etc.)>
MESSAGE:
MGMT_INFO_GOT_EVENTYPE: GOT EVENT TYPE <event type>
MESSAGE:
MGMT_INFO_MMDBGREW: Database grew by <growth in kbytes> KBytes (<portion in use> of <total usable> in use)
MESSAGE:
MGMT_INFO_MMDBSHRA: Database shrank by <shrinkage in Kbytes>KBytes ( <portion in use> of <total usable> in use)
MESSAGE:
MGMT_INFO_MMDBTRM1: <request>: termination request received
MESSAGE:
MGMT_INFO_MMDBTRM2: <request>: termination begins
MESSAGE:
MGMT_INFO_POM_COMMIT: Successfully committed provisioning data
MESSAGE:
MGMT_INFO_POM_DEPLOY: Successfully deployed provisioning data
MESSAGE:
MGMT_INFO_POM_EMPTYLINK: The provisioning link path is empty, maintaining existing link
MESSAGE:
MGMT_INFO_POM_NOTFINDSESS: Could not find session <session id> for <usage of find session <cancel/stop>>
MESSAGE:
MGMT_INFO_POM_SESS: POM session by <user id> for version <destination version> restored
MESSAGE:
MGMT_INFO_POM_SESSBUSY: Session is used by <session ID>, starting session rejected
MESSAGE:
MGMT_INFO_POM_SESSTIMEOUT: Session inactive. <result of the session timeout>
MESSAGE:
MGMT_INFO_POM_STARTSESS: Session started by <session id>
MESSAGE:
MGMT_INFO_POM_STOPSESS: Session stopped by <session id>
MESSAGE:
MGMT_INFO_STARTDYNCFG: Dynamic reconfiguration starting for table <name of table>
MESSAGE:
MGMT_INFO_STOPDYNCFG: Dynamic reconfiguration for table <name of table> complete
MESSAGE:
MGMT_WARN_MMDBTRM3: <request>: termination complete
DESCRIPTION:
Completed the disconnect from the TimesTen database.
MESSAGE:
MGMT_WARN_UNKN_INTERVAL: <name of receiver> received unknown bucket interval <bucket interval> for bucket <name of bucket>
DESCRIPTION:
An unsupported interval is specified for this bucket. Defaulting to the 24 hour interval.
MESSAGE:
MGMT_WARN_UPOBJ: Updating Object <name of object> compId <component id>
DESCRIPTION:
Updating (as part of dynamic reconfiguration) the specified component.
MESSAGE:
MML_INFO_COMMAND: MML Command <name of MML command entered>
MESSAGE:
PROT_ERR_BSM_ACTI_GRP: Failed to activate session grp <group ID> set <set ID> with err <error number>
DESCRIPTION:
This message is applicable only if the VSC is configured in fault tolerant mode. Valid values of err are:
•
•
MESSAGE:
PROT_ERR_MTP3: MTP3 Error Message from compId <component Id>: <general error string>
DESCRIPTION:
The general error string `CP DiscInd reason xx' indicates failure of SS7 link identified by the `compId' in the message. xx indicates the reasons for the failure. The following are the valid reasons:
00—Request from the layer management.
01—SURM failure.
02—Excessive length of align period.
03—T7 timer expiration.
04—Physical interface failure.
05—2 out of 3 invalid BSNs.
06—2 out of 3 invalid FIBs.
07—LSSU condition.
08—Excessive MTP2 congestion.
19—SIOS received in LSC.
20—T2 expired waiting for SIO.
22—SIOS received in IAC.
23—proving failure.
24—T1 expired waiting for FISU.
25—SIN received while in service.
32—CTS lost.
37—No resources.
MESSAGE:
PROT_ERR_RLM_DATA_RCV: No data received for RLM link <component id of RLM link>
DESCRIPTION:
No data was received on the RLM link. As a result, the VSC takes the RLM out of service. Check the communication with the NAS.
MESSAGE:
PROT_ERR_SRCP_BLD_PARMTYPE: compId :<component id>: Unknown or unsupported SRCP parameter type <encoded value of the event parameter type>
DESCRIPTION:
Indicates that the SRCP message cannot be built because the event parameter type is unknown or unsupported.
MESSAGE:
PROT_ERR_SRCP_PARSE_MAJVER: compId <component id>: SRCP major version mismatch <major version number>
DESCRIPTION:
This message indicates the major version number in the SRCP message does not match that supported by this version of software.
MESSAGE:
PROT_ERR_SRCP_PARSE_MINVER: compId <component id>: SRCP minor version mismatch <minor version number>
DESCRIPTION:
This message indicates the minor version number in the SRCP message does not match what this version of software supports.
MESSAGE:
PROT_ERR_SRCP_PARSE_PROT: compId <component id>: Protocol <protocol> not SRCP
DESCRIPTION:
The SRCP message cannot be parsed because the protocol field in the command line is not SRCP.
MESSAGE:
PROT_ERR_UNREGSTR: unregistered SIO from Engine <component id
DESCRIPTION:
The SS7 IOCC has received a message from the engine with an invalid SIO.
MESSAGE:
PROT_ERR_VSI_ENG_SERVICE: compId <Component Id>: Failed to add <`Engine write' or `IDU read'> service; <the requested IDU service or the Engine service>not defined
DESCRIPTION:
Used when adding the Engine write, IDU read service for the VSI.
MESSAGE:
PROT_ERR_VSI_RESYNC_CKSUMBLK_NOTFOUND:Checksum block <Checksum block> does not exist for slave id <slave id>
DESCRIPTION:
A checksum block could not be found during the resync procedure.
MESSAGE:
PROT_ERR_VSI_RESYNC_PENDLIST_EMPTY: <class::method name>: Empty pending List
DESCRIPTION:
The pending list is empty.
MESSAGE:
PROT_ERR_XGCP_BLD_CVLEN: compId <component id>: Incorrect length of control vector <control vector id>
DESCRIPTION:
Indicates an inconsistency in the message (encoded in binary data stream format) received from the upper layer, specifically the size of a particular parameter (control vector), and building of the message is aborted.
MESSAGE:
PROT_ERR_XGCP_BLD_EPID: compId <component id>: XGCP endpoint string error <endpoint id>
DESCRIPTION:
Indicates that the xgcp message cannot be built because the end point is either not specified or not able to process.
MESSAGE:
PROT_ERR_XGCP_BLD_EVT: compId <component id>: SGCP/MGCP event <encoded value of the event> out of range
DESCRIPTION:
Indicates that the SGCP/MGCP message cannot be built because the event specified is not in the associated package.
MESSAGE:
PROT_ERR_XGCP_BLD_RESP_CODE: compId <component id>: XGCP endpoint string error <response code>s
DESCRIPTION:
Indicates that the xgcp message cannot be built because the response code is invalid.
MESSAGE:
PROT_ERR_XGCP_BLD_SIGEVT: compId <component id>: SGCP/MGCP event <encoded value of the event> cannot be signaled.
DESCRIPTION:
Indicates that the SGCP/MGCP message cannot be built because the signal request parameter specifies a non-signallable SGCP/MGCP event.
MESSAGE:
PROT_ERR_XGCP_PARSE_EVT: compId <component id>: SGCP/MGCP event <first 3 letters of the event> not found in package <package>
DESCRIPTION:
Indicates that the SGCP/MGCP message cannot be parsed because it contains an event that cannot be found in the associated package.
MESSAGE:
PROT_ERR_XGCP_PARSE_EVTPARM: compId <component id>: Cannot parse SGCP/MGCP parameter for <package>/<event that carries the parameter>
DESCRIPTION:
Indicates that the SGCP/MGCP message cannot be parsed because it contains an event that carries an invalid or extraneous parameter.
MESSAGE:
PROT_ERR_XGCP_PARSE_LINE: compId <component id>: Cannot parse <message line>
DESCRIPTION:
Indicates that an entire line in the SGCP/MGCP message cannot be parsed.
MESSAGE:
PROT_ERR_XGCP_PARSE_MINVER: compId <component id>: SGCP/MGCP minor version mismatch <minor version number>
DESCRIPTION:
Indicates the minor version number in the SGCP/MGCP message does not match what this version of software supports.
MESSAGE:
PROT_ERR_XGCP_PARSE_PKG: compId <component id>: SGCP/MGCP package <first letter of the package>.1s not found
DESCRIPTION:
Indicates that the SGCP/MGCP message cannot be parsed because it contains an unrecognized package.
MESSAGE:
PROT_ERR_XGCP_PARSE_PROT: compId <component id>: Protocol <protocol> not SGCP/MGCP
DESCRIPTION:
Indicates that the SGCP/MGCP message cannot be parsed because the protocol field in the command line is not SGCP/MGCP.
MESSAGE:
PROT_INFO_ADD_PTCODE: compId <Component Id> :Unable to add <type of point code> Pt Code
MESSAGE:
PROT_INFO_ASN_LNK_CNTL: ASN channel <component id> state change <state change information> cause <reason for state change>
MESSAGE:
PROT_INFO_ASN_PATH_CNTL: ASN path <component id> state change <state change information> cause <reason for state change>
MESSAGE:
PROT_INFO_BAD_STAT: compId <component id> :cfgTrilliumLinkset linkset - bad state
MESSAGE:
PROT_INFO_BAD_TRANS: bad <SSC> transition <component id>
MESSAGE:
PROT_INFO_BSM_ACTI_GRP: Activate session grp %i set %i
MESSAGE:
PROT_INFO_BSM_LINK_DOWN: Receive IO_DATA_LINK_DOWN for set %i grp %i sess %i
MESSAGE:
PROT_INFO_BSM_LINK_RESET: Receive IO_DATA_LINK_RESET for set %i grp %i sess %i
MESSAGE:
PROT_INFO_BSM_LINK_UP: Receive IO_DATA_LINK_UP for set %i grp %i sess %i
MESSAGE:
PROT_INFO_BSM_SESS_EXIST: Session %i already exists in group %i
MESSAGE:
PROT_INFO_BSM_STBY_GRP: Standby session grp %i set %i
MESSAGE:
PROT_INFO_B_SSC_TRANS: Path <component id>: B-Chan <previous state>: B-SSC trans <current state>
MESSAGE:
PROT_INFO_CHANGE_LOG_LVL: Changing logging level to <new logging level (DEBUG, INFO, etc.)>
MESSAGE:
PROT_INFO_CHNA_DEL_REQ: Received SSC request for deleted channel <component id of deleted channel>
MESSAGE:
PROT_INFO_CRT_SESS_MNGR: Created Session Manager
MESSAGE:
PROT_INFO_DPC_NOT_CONFIG: compId <component id of Destination Point Code> :Destination Pt code not configured properly
MESSAGE:
PROT_INFO_DPNSS: Info message from DPNSS: <Text of the message>
MESSAGE:
PROT_INFO_DPNSS_BEAR_CNTL: DPNSS channel %lx state change %s channel %s
MESSAGE:
PROT_INFO_DPNSS_LNK_CNTL: DPNSS channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_IDU_TOO_BIG: <component id>: PDU size (<size of PDU>) exceeds max<maximum PDU size> size
MESSAGE:
PROT_INFO_IOCC_INIT: Initializing IOCC: <component id of channel controller>
MESSAGE:
PROT_INFO_IOCC_KILL: killing Channel Controller
MESSAGE:
PROT_INFO_IP: Info message from IP: <Text of the message>
MESSAGE:
PROT_INFO_IP_LNK_CNTL: IP channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_ISDN: Info message from ISDN: <general information string>
MESSAGE:
PROT_INFO_KILL_SESS_MNGR: Terminating Session Manager
MESSAGE:
PROT_INFO_MSG_UNKNLINK: compId <component id> :RLM message for unknown link
MESSAGE:
PROT_INFO_MTP3:compId <component id> %s
MESSAGE:
PROT_INFO_MTP3_LNK_CNTL: Link %lx state change %s cause %s
MESSAGE:
PROT_INFO_MTP3_LOOPBACK: <enable or disabled> MTP3 loopback
MESSAGE:
PROT_INFO_MTP3_LSET_CNTL: Linkset %lx state change %s cause %s
MESSAGE:
PROT_INFO_MTP3_PC_CNTL: Point code %lx state change %s cause %s
MESSAGE:
PROT_INFO_NOT_CONFIG: compId <Component Id> : Unable to configure <type of point code, for example,user, MTP3> for pt code <Component Id of the point code>
MESSAGE:
PROT_INFO_NOT_DEF_FOR: <name of channel (i.e. bearer)> ( <channel id>) is not defined for <component id of channel>
MESSAGE:
PROT_INFO_OPC_NOTCONFIG: compId <component id>:Origination Pt code not configured
MESSAGE:
PROT_INFO_PATH_PC_SSC: Path %08lx: PC SSC - trans %i
MESSAGE:
PROT_INFO_PATH_SSC: Path %08lx: SSC - trans %i cause %i
MESSAGE:
PROT_INFO_PLAT_ABORT: Platform state abort
MESSAGE:
PROT_INFO_PLAT_ACTIVE: Setting platform active
MESSAGE:
PROT_INFO_PLAT_CNTRL_SWITCH: Setting platform controlled switchover
MESSAGE:
PROT_INFO_PLAT_FRCD_SWITCH: Setting platform forced switchover
MESSAGE:
PROT_INFO_PLAT_OUT_OF_SRV: Setting platform out-of-service
MESSAGE:
PROT_INFO_PLAT_STANDBY: Setting platform standby
MESSAGE:
PROT_INFO_PRIOCNTL_REALTIME: Priocntl <channel controller name> now Real Time!!!
MESSAGE:
PROT_INFO_PROC_CTRL_REQ: <component id>: procCtrlReq(), status: <state transition>
MESSAGE:
PROT_INFO_Q921_LNK_CNTL: Q921 channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_RCVD_FROM_ICOM: Received <SSC name> from IOCM
MESSAGE:
PROT_INFO_RCVD_SSC: <class name>, received ssc msg from IOCM
MESSAGE:
PROT_INFO_RCV_SSC_REQ: Received SSC request <name of SSC request> for RLM link <component id>
MESSAGE:
PROT_INFO_RCV_UNSUP_SSC_REQ: Received unsupported SSC request for channel <component id>
MESSAGE:
PROT_INFO_REINIT_TCP: compId <component id of TCP channel> :Re-initializing TCP channel
MESSAGE:
PROT_INFO_REM_SIGCHAN: <component id of SigChan>: removeSigChan
MESSAGE:
PROT_INFO_REQ_CHAN_DEL: Received SSC request for deleted channel <component id of channel>
MESSAGE:
PROT_INFO_RESUM_RLM_PROC: Resuming RLM processing for group <group ID>
MESSAGE:
PROT_INFO_RLM_GROUP_CNTL: RLM channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_RLM_NOTENA: Rlm enabled: port <port number>
MESSAGE:
PROT_INFO_RUDP_LNK_CNTL: RUDP channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_SENDFAIL: Unable to send link statistics to IOCM
MESSAGE:
PROT_INFO_SEND_IDU: <component id of channel which is sending IDU>: Send IDU to Eng
MESSAGE:
PROT_WARN_SERV_STAT_CHG: <component id>:procSSCMsgToChanMgr(), invalid status <status>
MESSAGE:
PROT_INFO_SERV_STAT_CHG: <component id>: procSSCMsgToChanMgr(), status: <status> - incorrect
MESSAGE:
PROT_INFO_SESS_ADD: <component id of session>: Session added successfully
MESSAGE:
PROT_INFO_SM_SET_CNTL: SM channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_SS7_CFG_MSG: Received SS7 <the name of Module> cfg msg from IOCM
MESSAGE:
PROT_INFO_SSC_TO_CHANMGR: <component id>: SSC Msg to ioChanMgr, status: <status>
MESSAGE:
PROT_INFO_TCP_LNK_CNTL: TCP channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_TIMER_NOTAVA: Unable to allocate <the name of timer> timer
MESSAGE:
PROT_INFO_UDP_LNK_CNTL: UDP channel %lx state change %s cause %s
MESSAGE:
PROT_INFO_UNEX_MSG: compId <component id> :<message type> message to unexpected component
MESSAGE:
PROT_INFO_UNSUP_REQ_CHAN: Received unsupported SSC request for channel <component id>
MESSAGE:
PROT_INFO_UNXP_CODE_STAT: Unexpected Pt code status <status> for <component id>
MESSAGE:
PROT_INFO_VSI_CFG_MSG: compId <component id of SigChan>: Received sig chan config msg from channel manager
DESCRIPTION:
Indicates the receipt of the configuration message from the channel manager.
MESSAGE:
PROT_INFO_VSI_MASTER: compId <Component Id>: VSI Master log <info log from Master>
DESCRIPTION:
Displays information level messages from VSI Master API.
MESSAGE:
PROT_INFO_VSI_RESP_RCV: <class::method>: received <ACK or NAK> response
DESCRIPTION:
Highlights an ACK/NAK response from the slave.
MESSAGE:
PROT_INFO_VSI_SIG_CHAN: VSI Sig Can <component id>, state changed to <current state>, cause <cause for the state transition>
DESCRIPTION:
Indicates the status change on a VSI signaling channel.
MESSAGE:
PROT_INFO_VSI_SIG_PATH: VSI Sig Path <component id>, state changed to <current state>, cause <cause for state transition>
DESCRIPTION:
Indicates the status change on a VSI signaling path.
MESSAGE:
PROT_INFO_WAIT_NET_STABLE: RLM group <RLM group id>: waiting for network to stabilize
MESSAGE:
PROT_TRACE_ASN_PDU: Hex dump of ASN messages %lx %d %s
MESSAGE:
PROT_TRACE_ATM_AAL5_CLOSE: compId <componentId>: Deleting Stream <info on DSL number and File descriptor>
DESCRIPTION:
Indicates the closing of an AAL5 interface.
MESSAGE:
PROT_TRACE_ATM_AAL5_OPEN: compId <componentId>: IO stream AAL5 Open interface <name of the interface>
DESCRIPTION:
Indicates the opening of an AAL5 interface.
MESSAGE:
PROT_TRACE_ATM_SEND: SEND TO >>>> <component Id of the port on which message is sent> <: <VPCI to which message was sent>
DESCRIPTION:
Indicates that an ATM message has been sent.
MESSAGE:
PROT_TRACE_DPNSS_PDU: Hex dump of DPNSS messages %lx %d %s
MESSAGE:
PROT_TRACE_IP_PDU: Hex dump of IP message %lx %d %s
MESSAGE:
PROT_TRACE_MGCP_FROM_GW: compId: <component ID>, MGCP msg from gateway, IP: <gateway's IP address>, msg: <message>
DESCRIPTION:
Captures an MGCP message from the gateway.
MESSAGE:
PROT_TRACE_MGCP_TO_GW: compId: <component ID>, MGCP msg to gateway, IP: <gateway's IP address>, msg: <message>
DESCRIPTION:
Captures an MGCP message to the gateway.
MESSAGE:
PROT_TRACE_MTP3_PDU: Hex dump of MTP3 and UP messages %lx %d %s
MESSAGE:
PROT_TRACE_Q921_PDU: Hex dump of Q921 messages %lx %d %s
MESSAGE:
PROT_TRACE_RLM_PDU: Hex dump of RLM messages %lx %d %s
MESSAGE:
PROT_TRACE_RUDP_PDU: Hex dump of RUDP messages %lx %d %s
MESSAGE:
PROT_TRACE_SM_PDU: Hex dump of SM messages %lx %d %s
MESSAGE:
PROT_TRACE_SRCP_FROM_GW: compId: <component ID>, SRCP msg from gateway, IP: <gateway's IP address>, msg: <message>
DESCRIPTION:
Captures an SRCP message from the gateway.
MESSAGE:
PROT_TRACE_SRCP_TO_GW: compId: <component ID>, SRCP msg to gateway, IP: <gateway's IP address>, msg: <message>
DESCRIPTION:
Captures an SRCP message to the gateway.
MESSAGE:
PROT_TRACE_TCAP_PDU_RX: Hex dump of TCAP message received, SSN= <Subsystem number in the message>, LEN= <Length of the trace data>, <Hex dump of TCAP PDU>
MESSAGE:
PROT_TRACE_TCAP_PDU_TX: Hex dump of TCAP message transmitted, SSN= <Subsystem number in the message>, LEN= <Length of the trace data>, <Hex dump of TCAP PDU>
MESSAGE:
PROT_TRACE_TCP_PDU: Hex dump of TCP messages %lx %d %s
MESSAGE:
PROT_TRACE_UDP_PDU: Hex dump of UDP messages %lx %d %s
MESSAGE:
PROT_TRACE_VSI_MASTER_MSG_SEND: Sending message to client. Message type <message type being sent>
DESCRIPTION:
The master is sending a message to the client.
MESSAGE:
PROT_TRACE_VSI_PDU: Hex dump of VSI messages <component id> <from or to Media Gateway Controller (0 FROM, 1 TO)> <Hex dump of PDU>
DESCRIPTION:
Dumps the VSI PDU information when VSI messages are sent or received.
MESSAGE:
PROT_TRACE_VSI_PROCCTRLREQ: compId <Component Id>: procCtrlReq - status <current status>
DESCRIPTION:
A ProcCtrlReq has been received from the channel manager.
MESSAGE:
PROT_WARN_ENG_FULL: Engine IPC is full: pending incoming IDUs
DESCRIPTION:
An IOCC is not able to send the messages received from the network to the engine. Verify whether the engine is or is not processing the calls.
MESSAGE:
PROT_WARN_PROC_CTRL_REQ: <component id> :procCtrlReq() <contents of buffer>
MESSAGE:
PROT_WARN_TCP: TCP Warning Message <general error string>
MESSAGE:
PROT_WARN_XGCP_PARSE_LONGCOMM: compId <component id>: Long SGCP/MGCP comment truncated <comment>
DESCRIPTION:
The SGCP/MGCP message contains a long comment, and only a truncated copy will be passed to the upper layer.
MESSAGE:
TIOS_ERR_CDNG_INV: physLineIf: <component id of physical line> - coding %s is invalid for CEPT carrier
DESCRIPTION:
The line coding type has been configured incorrectly for the specified physical interface. Check the configuration for the specified physical interface.
MESSAGE:
TIOS_ERR_INVALIDCARD: Invalid Cardtype <cardtype> for line <component id of line>
DESCRIPTION:
Indicates a configuration error for the line.
MESSAGE:
TIOS_ERR_INV_CARD: %08lx - invalid card %s or line %s
DESCRIPTION:
Indicates a configuration error for the physical interface.
MESSAGE:
TIOS_ERR_INV_CARRIER: %s %C - invalid carrier %s
DESCRIPTION:
Indicates a configuration error in the physical interface.
MESSAGE:
TIOS_ERR_INV_PROT: invalid Transport protocol= %s in stp.dat
DESCRIPTION:
Indicates a configuration error in SS7 subsystem.
MESSAGE:
TIOS_ERR_IN_STATE: in State <name of the current state>
DESCRIPTION:
This message is informational and does not indicate an error.
MESSAGE:
TIOS_ERR_LINKFAIL: compId <component id of link>: No link with prio=1
DESCRIPTION:
Indicates a configuration error. No SS7 link with priority 1 is configured in the linkset indicated by the component ID.
MESSAGE:
TIOS_ERR_NOCARDCOMP: <component id of card>: No containing card component
DESCRIPTION:
An entry in the sigChanDev.dat file uses a card that is not provisioned.
MESSAGE:
TIOS_ERR_NOLINE: <component id of line>: No line entry
DESCRIPTION:
An entry in the sigChanDev.dat file is referring to a nonexistent entry in the physLineIf.dat file.
MESSAGE:
TIOS_ERR_NOLINECOMP: <component id of line component>: No containing line component
DESCRIPTION:
An entry in the sigChanDev.dat file is referring to a nonexistent entry in the physLineIf.dat file.
MESSAGE:
TIOS_ERR_NOTDEF: OPC <component id of OPC> or APC <component id of APC>: not defined for route compId <component id of route>
DESCRIPTION:
Indicates a configuration error for an APC; either parameter 1 or parameter 2 in the error message is not defined in the dpc.dat file.
MESSAGE:
TIOS_ERR_NO_ENTRY: FAILURE: <component id of sigChan>: No sigChanDev or sigChanDevIp Entry
DESCRIPTION:
The parameter in the log message is not defined in either the sigChanDev.dat file or the sigChanDevIp.dat file.
MESSAGE:
TIOS_ERR_PROC_EXIST: <component id of process> component does not exist in process
DESCRIPTION:
The specified internal component does not exist in the process reporting the error. There is no MML mapping to the component ID, indicating that there is no component entry.
MESSAGE:
TIOS_ERR_PROTNOFOUND: Signaling Terminal Port Number not found.
DESCRIPTION:
Indicates a configuration error in the XECfgParm.dat file. The parameter stPort must be defined for the SS7 channel controllers to function properly.
MESSAGE:
TIOS_ERR_RECONFIG_FAIL: <component ID of component being reconfigured> reconfigure failed, <component ID of component in wrong state> must not be IS
DESCRIPTION:
The DPC specified in the first parameter must be taken out of service to reconfigure the component specified in the second parameter.
MESSAGE:
TIOS_ERR_SCCP_MEAS: Error in SCCP measurement collection
DESCRIPTION:
Indicates an error in retrieving the SCCP measurements from the trillium SCCP stack. As a result, the measurement counters for the SCCP will not show the correct values.
MESSAGE:
TIOS_ERR_TCAPMSG: Error in processing TCAP message. Invalid/missing <Name of the parameter associated with the error>, param = <Parameter1 value>,param2= <Parameter2 value>
DESCRIPTION:
A TCAP message could not be processed in the trillium TCAP stack because of invalid or missing parameters. The following invalid or missing parameters are reported:
•
•
•
•
MESSAGE:
TIOS_ERR_TCAPSTACK: Error from TCAP stack. FAILURE: <Error type>. param1= <Parameter associated with the error>,param2= <Parameter associated with the error>
DESCRIPTION:
The dynamic reconfiguration might have failed as a result of this error.
MESSAGE:
TIOS_ERR_UNKNOWN_IPADDR: Unknown IP address <peer or local>
DESCRIPTION:
Indicates a configuration error in the XECfgParm.dat file. IP_Addr1, IP_Addr2, IP_Addr3, IP_Addr4 parameters are possibly not defined in this file.
MESSAGE:
TIOS_ERR_UNKN_CKPT: Unknown <name of the checkPt port> checkpoint port
DESCRIPTION:
The parameter chkPtPort is not defined in the XECfgParm.dat file.
MESSAGE:
TIOS_ERR_UNKN_COMPTP: Component type <name of the comp type> is not defined in compTypes.dat
DESCRIPTION:
The component type is not defined in the compTypes.dat file.
MESSAGE:
TIOS_ERR_UNKN_MGC: Unknown Media Gateway Controller: <Media Gateway Controller name>
DESCRIPTION:
The parameters ownTranspathId and/or peerTranspathId are not defined in the XECfgParm.dat file.
MESSAGE:
TIOS_ERR_UNKN_MSG: Unknown meas for <component id>, measNm <measurement name>
DESCRIPTION:
The measNm parameter is not defined in the measCats.dat file.
MESSAGE:
TIOS_ERR_UNKN_PLTST: Parameter `desiredPlatformState' is not defined in XECfgParm.dat
DESCRIPTION:
The parameter desiredPlatformState is not defined in the XECfgParm.dat file.
MESSAGE:
TIOS_ERR_UNKN_PROPERTY: Property <Property prefix>. <Property name> is not defined in properties.dat. Info = <Additional informational parameter>
DESCRIPTION:
The property identified by the parameters in the message is not defined in the properties.dat file.
MESSAGE:
TIOS_ERR_UNKN_STRING_PROPERTY: String property <Property prefix> - <Property name> not defined in properties.dat. Info= <Additional informational parameter>
DESCRIPTION:
The property identified in the parameters in the message is not defined in the properties.dat file.
MESSAGE:
TIOS_ERR_UNKN_TIOS_FAM: <data file name for which the error is detected> unknown proto family <protocol family name that is not recognized> for sigpath <Component name>
DESCRIPTION:
The sigPath.dat file contains a record with an unknown protocol family name.
MESSAGE:
TIOS_ERR_UNREC_CARD: <class name>: unrecognized card type <card type>
DESCRIPTION:
Iindicates an error in one of the records in the sigChanDev.dat file.
MESSAGE:
TIOS_INFO_CRSER: ioCardABC compId <component id of service>: createService
MESSAGE:
TIOS_INFO_DELOBJ: Deleting object <component id of object being deleted>
MESSAGE:
TIOS_INFO_DLD: compId <component id of module being downloaded>: Downloaded <name of module being downloaded>
DESCRIPTION:
MGCP signal path information.
MESSAGE:
TIOS_INFO_FIND_IOCC_FAIL: Cannot find ioCC <component id of channel controller not found>: Creating <component id of new channel controller being created>
MESSAGE:
TIOS_INFO_GETALA: ioCardABC compId <component id of card>: trying to get alarms
MESSAGE:
TIOS_INFO_INIT_ACTV: INIT: Active Mode
MESSAGE:
TIOS_INFO_INIT_STBY: INIT: Standby Mode
MESSAGE:
TIOS_INFO_NOT_IMPL: <component id>: NOT IMPL fault= <fault id> state= <state id>
MESSAGE:
TIOS_INFO_PORTFOUND: Found Signaling Terminal Port Number <port number>
MESSAGE:
TIOS_INFO_RCMSG: ioCardABC compId <component id>: rcv XERawMsg
MESSAGE:
TIOS_INFO_RCVERRMSG: ioCardABC compId <component id>: rcv ioCardIpcErrorMsg
MESSAGE:
TIOS_INFO_RECON: <component id>: RECON state= <SVC state>
MESSAGE:
TIOS_INFO_SCCP_USER_IS: SCCP User IS: Switch=<protocol type (ANSI/ITU)>,suId= <SCCP Service user Id>
MESSAGE:
TIOS_INFO_SCCP_USER_OOS: SCCP User OOS: Switch=<protocol type (ANSI/ITU)>,suId=<SCCP Service user Id>
MESSAGE:
TIOS_INFO_SSN_STATE: SSN State change for SSN = <Subsystem number>, DPC= <DPC>: new state = <new state>
MESSAGE:
TIOS_WARN_AUDIT_CMPLT: <component id>: Gateway AUDIT already retrieved and complete (command = <command>)
DESCRIPTION:
The gateway audit is complete.
MESSAGE:
TIOS_WARN_AUDIT_RESP: Gateway Audit Response string = <contents of the audit response>
DESCRIPTION:
The gateway audit response is received.
MESSAGE:
TIOS_WARN_AUDIT_RNNG: <component id>: Gateway audit in progress - request <command> ignored
DESCRIPTION:
The gateway audit is in progress. The request translation table is as follows:
0—Undefined
1—GW_START
2—LINE_START
3—GW_RESPONSE
4—LINE RESPONSE
5—GW-RTRV
6—LINE-RTRV
MESSAGE:
TIOS_WARN_CKPT_SSC: compId <Component Id>: CHKPT SSC trans= <Transition id>, cause= <Error number>
DESCRIPTION:
This log message should appear only on the STANDBY VSC and indicates the receipt of a checkpointing event for a signaling channel. The value of the cause is always 0 and can be ignored.
MESSAGE:
TIOS_WARN_DIST_INV: distance <Value of distVal parameter which is wrong> is not valid for CEPT carrier
DESCRIPTION:
The distVal parameter for one of the records in the physLineIf.dat file is incorrect. A distVal of 75 is assumed.
MESSAGE:
TIOS_WARN_FAS_SSC_XMIT: <component id>: Transmitted FAS IP Service State Change=<new service state>, Cause=<cause for change to new service state>
DESCRIPTION:
A Service State Change event has been sent. SSC translations are as follows:
0=CAUSE_UNKNOWN
1=CAUSE_NA
2=CONFIG_FAIL
3=LINE_FAIL
4=LINKSET_FAIL
5=LINK_FAIL
6=ENGINE_RESET
7=CAUSE_COMMANDED_OOS
8=CAUSE_COMMANDED_IS
9=SUPPORTING_ENTITY
10=OOS_PENDING
11=IS_PENDING
12=TRAFFIC_PATH
Causes of C7 A-OOS
13=C7_SignalErr
14=C7_BSNR_FIBR
15=C7_LinkCongestion
16=C7_AckDelay
17=C7_LocalInhibit
18=C7_RemoteInhibit
19=C7_LocalBlocked
20=C7_RemoteBlocked
21=C7_LocalUninhibit
22=C7_RemoteUninhibit
23=C7_LocalUnblocked
24=C7_RemoteUnblocked
25=C7_LocalInhibitDeny
26=CongLocal
27=CongRemote
28=CAUSE_ACTIVE
29=CAUSE_STBY
30=MGCP_HEARTBEAT_FAILED
31=SRCP_HEARTBEAT_FAILED
32=SRCP_AUDIT_GW_TYPE_FAILED
33=SRCP_AUDIT_GW_SLOT_NUM_FAILED
34=SRCP_AUDIT_GW_NUM_OF_LINES_FAILED
35=SRCP_AUDIT_GW_BACKHAUL_PROTOCOL_FAILED
36=SRCP_AUDIT_GW_CONTROL_PROTOCOL_FAILED
37=SRCP_AUDIT_GW_COORD_PROTOCOL_FAILED
38=SRCP_AUDIT_GW_NUM_OF_BACKHAUL_SESSIONS_FAILED
39=SRCP_AUDIT_GW_CU_IP_ADDR_FAILED
40=SRCP_AUDIT_GW_CU_IP_PORT_FAILED
41=SRCP_AUDIT_GW_SU_IP_ADDR_FAILED
42=SRCP_AUDIT_GW_SU_IP_PORT_FAILED
43=SRCP_AUDIT_LINE_SIG_PROTOCOL_FAILED
44=SRCP_AUDIT_LINE_CODING_FAILED
45=SRCP_AUDIT_LINE_STATE_FAILED
46=SRCP_AUDIT_LINE_LOOPBACK_FAILED
47=C7_Prohibit
48=C7_Restrict
49=C7_SRT_PASSED
50=C7_SRT_FAILED
Cause code translation:
0 = UNDEFINED_TRANS
1 = CREATE
2 = DELETE
3 = COMMANDED_IS
4 = COMMANDED_OOS
5 = FAILED
6 = RESTORED
7 = RESET
8 = CONGESTION
9 = FORCED_OOS
10= COMMANDED_INH
11= COMMANDED_UNINH
12= COMMANDED_EMRG_ALIGN
13= ENG_IS
14= ENG_OOS
15= RESTART_DCHANS
MESSAGE:
TIOS_WARN_FAULT: <component id>: FAULT=<fault id> <active or clear>
DESCRIPTION:
Indicates a change in an alarm state for the given component.
MESSAGE:
TIOS_WARN_SC_SSC_RCV: <component id>: Received Signal Channel Service State Change=<new service state>, Cause=<cause for change to new service state>
DESCRIPTION:
A Service State Change event has been received. SSC translations are as follows:
0=CAUSE_UNKNOWN
1=CAUSE_NA
2=CONFIG_FAIL
3=LINE_FAIL
4=LINKSET_FAIL
5=LINK_FAIL
6=ENGINE_RESET
7=CAUSE_COMMANDED_OOS
8=CAUSE_COMMANDED_IS
9=SUPPORTING_ENTITY
10=OOS_PENDING
11=IS_PENDING
12=TRAFFIC_PATH
Causes of C7 A-OOS
13=C7_SignalErr
14=C7_BSNR_FIBR
15=C7_LinkCongestion
16=C7_AckDelay
17=C7_LocalInhibit
18=C7_RemoteInhibit
19=C7_LocalBlocked
20=C7_RemoteBlocked
21=C7_LocalUninhibit
22=C7_RemoteUninhibit
23=C7_LocalUnblocked
24=C7_RemoteUnblocked
25=C7_LocalInhibitDeny
26=CongLocal
27=CongRemote
28=CAUSE_ACTIVE
29=CAUSE_STBY
30=MGCP_HEARTBEAT_FAILED
31=SRCP_HEARTBEAT_FAILED
32=SRCP_AUDIT_GW_TYPE_FAILED
33=SRCP_AUDIT_GW_SLOT_NUM_FAILED
34=SRCP_AUDIT_GW_NUM_OF_LINES_FAILED
35=SRCP_AUDIT_GW_BACKHAUL_PROTOCOL_FAILED
36=SRCP_AUDIT_GW_CONTROL_PROTOCOL_FAILED
37=SRCP_AUDIT_GW_COORD_PROTOCOL_FAILED
38=SRCP_AUDIT_GW_NUM_OF_BACKHAUL_SESSIONS_FAILED
39=SRCP_AUDIT_GW_CU_IP_ADDR_FAILED
40=SRCP_AUDIT_GW_CU_IP_PORT_FAILED
41=SRCP_AUDIT_GW_SU_IP_ADDR_FAILED
42=SRCP_AUDIT_GW_SU_IP_PORT_FAILED
43=SRCP_AUDIT_LINE_SIG_PROTOCOL_FAILED
44=SRCP_AUDIT_LINE_CODING_FAILED
45=SRCP_AUDIT_LINE_STATE_FAILED
46=SRCP_AUDIT_LINE_LOOPBACK_FAILED
47=C7_Prohibit
48=C7_Restrict
49=C7_SRT_PASSED
50=C7_SRT_FAILED
Cause code translation:
0 = UNDEFINED_TRANS
1 = CREATE
2 = DELETE
3 = COMMANDED_IS
4 = COMMANDED_OOS
5 = FAILED
6 = RESTORED
7 = RESET
8 = CONGESTION
9 = FORCED_OOS
10= COMMANDED_INH
11= COMMANDED_UNINH
12= COMMANDED_EMRG_ALIGN
13= ENG_IS
14= ENG_OOS
15= RESTART_DCHANS
MESSAGE:
TIOS_WARN_SC_SSC_XMIT: <component id>: Transmitted Signal Channel Service State Change=<new service state>, Cause=<cause for change to new service state>
DESCRIPTION:
Service State Change event has been sent. SSC translations follow:
0=CAUSE_UNKNOWN
1=CAUSE_NA
2=CONFIG_FAIL
3=LINE_FAIL
4=LINKSET_FAIL
5=LINK_FAIL
6=ENGINE_RESET
7=CAUSE_COMMANDED_OOS
8=CAUSE_COMMANDED_IS
9=SUPPORTING_ENTITY
10=OOS_PENDING
11=IS_PENDING
12=TRAFFIC_PATH
Causes of C7 A-OOS
13=C7_SignalErr
14=C7_BSNR_FIBR
15=C7_LinkCongestion
16=C7_AckDelay
17=C7_LocalInhibit
18=C7_RemoteInhibit
19=C7_LocalBlocked
20=C7_RemoteBlocked
21=C7_LocalUninhibit
22=C7_RemoteUninhibit
23=C7_LocalUnblocked
24=C7_RemoteUnblocked
25=C7_LocalInhibitDeny
26=CongLocal
27=CongRemote
28=CAUSE_ACTIVE
29=CAUSE_STBY
30=MGCP_HEARTBEAT_FAILED
31=SRCP_HEARTBEAT_FAILED
32=SRCP_AUDIT_GW_TYPE_FAILED
33=SRCP_AUDIT_GW_SLOT_NUM_FAILED
34=SRCP_AUDIT_GW_NUM_OF_LINES_FAILED
35=SRCP_AUDIT_GW_BACKHAUL_PROTOCOL_FAILED
36=SRCP_AUDIT_GW_CONTROL_PROTOCOL_FAILED
37=SRCP_AUDIT_GW_COORD_PROTOCOL_FAILED
38=SRCP_AUDIT_GW_NUM_OF_BACKHAUL_SESSIONS_FAILED
39=SRCP_AUDIT_GW_CU_IP_ADDR_FAILED
40=SRCP_AUDIT_GW_CU_IP_PORT_FAILED
41=SRCP_AUDIT_GW_SU_IP_ADDR_FAILED
42=SRCP_AUDIT_GW_SU_IP_PORT_FAILED
43=SRCP_AUDIT_LINE_SIG_PROTOCOL_FAILED
44=SRCP_AUDIT_LINE_CODING_FAILED
45=SRCP_AUDIT_LINE_STATE_FAILED
46=SRCP_AUDIT_LINE_LOOPBACK_FAILED
47=C7_Prohibit
48=C7_Restrict
49=C7_SRT_PASSED
50=C7_SRT_FAILED
Cause code translation:
0 = UNDEFINED_TRANS
1 = CREATE
2 = DELETE
3 = COMMANDED_IS
4 = COMMANDED_OOS
5 = FAILED
6 = RESTORED
7 = RESET
8 = CONGESTION
9 = FORCED_OOS
10= COMMANDED_INH
11= COMMANDED_UNINH
12= COMMANDED_EMRG_ALIGN
13= ENG_IS
14= ENG_OOS
15= RESTART_DCHANS
MESSAGE:
TIOS_WARN_UNKN_LF: line <field name> type <value that is not recognized> is not recognized
DESCRIPTION:
The value of the field identified by the first parameter in one of the records in the physLineIf.dat file is not recognized.
MESSAGE:
TIOS_WARN_XMIT_AUDIT: <Message id>: XMIT AUDIT command <Command in the message>
DESCRIPTION:
This message is generated when a gateway audit message is sent.
MESSAGE:
PROT_TRACE_SIP_FROM_GW: compId: <component ID>, SIP msg from gateway, IP: <gateway's IP address>, msg: <message>
DESCRIPTION:
Captures a SIP message from the gateway.
MESSAGE:
PROT_TRACE_SIP_TO_GW: compId: <component ID>, SIP msg to gateway, IP: <gateway's IP address>, msg: <message>
DESCRIPTION:
Captures a SIP message to the gateway.
MESSAGE:
ENV_ERR_DNS_BIND: failed to bind to a port for processing DNS queries: <bind() Error code>
DESCRIPTION:
The SIP IOCC failed to bind to any of the specified DNS ports. The ports could be in use by other applications.
MESSAGE:
TIOS_WARN_DNS_QUERYFAIL: failed to send DNS query msg: <IP address>
DESCRIPTION:
Occurs when the SIP IOCC sends a DNS query to the network.
MESSAGE:
TIOS_WARN_DNS_QUERYTIMEOUT: DNS Query Timeout for IP: <destination IP address>
DESCRIPTION:
The SIP IOCC sent a DNS query to the DNS server and did not receive the DNS response on time.
MESSAGE:
TIOS_INFO_DNS_UP: local SIP DNS state changed to UP
DESCRIPTION:
The SIP changed the local DNS state to UP.
MESSAGE:
TIOS_INFO_DNS_DOWN: local SIP DNS state changed to DOWN
DESCRIPTION:
The SIP changed the local DNS state to DOWN.
MESSAGE:
TIOS_ERR_SOCKET_ICMP: <class::method> failed to open a raw socket for ICMP msg processing:<socket() return code>
DESCRIPTION:
An error occurred when creating a raw socket. The socket can be opened only by a superuser.
MESSAGE:
GEN_ERR_UNKNOWN_MSG: <component ID>: Unrecognized or unknown message <Method name> <Content of the buffer>
DESCRIPTION:
Unable to process a message from either the engine or the gateway.
TAC Log Messages
The following log messages are intended to assist the Cisco Technical Assistance Center (TAC) in troubleshooting customer problems. Use of these messages frequently requires knowledge of the programming code used in the Cisco MGC software. Therefore, these messages have not been described for the end user; they are listed here, in alphabetical order, for reference purposes only.
If you receive one of the following messages, contact the Cisco TAC for assistance. See the preface for information about contacting the Cisco TAC.
MESSAGE:
CP_CRIT_ADD_CHGHNDLR: %s: failed to add change handler
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_CRIT_ADD_PROPTBL: %s: failed to add engine properties table
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_CRIT_ASP_ID: %s: failed to find ASP comp ID
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_CRIT_ASP_TYPE: %s: type for ASP is not specified in comType.dat table
Note
PARAMETERS:
%s:class::method
MESSAGE:
CP_CRIT_CHPT_EVTHNDLR: %s: failed to install CHPT event handler %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: status string
MESSAGE:
CP_CRIT_CRT_MGRS: %s: failed to create data mgr or call mgr
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_CRIT_EVTHNDLR: %s: failed to instantiate all event handlers
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_CRIT_EXT_EVTHNDLR: %s: failed to install external event handler %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: status string
MESSAGE:
CP_CRIT_FIND_CC_PARM: %s: failed to find call-context file parm %s, %s
Note
PARAMETERS:
%s: class::method
%s: parameter not found
%s: reason
MESSAGE:
CP_CRIT_FIND_MDL_PARM: %s: failed to find MDL file parm %s, %s
Note
PARAMETERS:
%s: class::method
%s: parameter not found
%s: reason
MESSAGE:
CP_CRIT_INIT_IMPEXP: %s: failed to init MDL import/export parms
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_CRIT_INIT_SIGS: %s: failed to init signals
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_CRIT_INT_EVTHNDLR: %s: failed to install internal event handler %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: status string
MESSAGE:
CP_CRIT_IOS_EVTHNDLR: %s: failed to install IOS event handler %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: status string
MESSAGE:
CP_CRIT_LOAD: %s: failed to load %s from %s
Note
PARAMETERS:
%s: class::method
%s: LCM or CC
%s: fileName
MESSAGE:
CP_CRIT_MML_EVTHNDLR: %s: failed to install mml event handler %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: status string
MESSAGE:
CP_CRIT_PROC_EVTHNDLR: %s: failed to install PROC event handler %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: status string
MESSAGE:
CP_CRIT_REGSERVICE: %s: failed to register %s service
Note
PARAMETERS:
%s: class method
%s: service name
MESSAGE:
CP_CRIT_REG_MDLFUNC: %s: failed to register mdl function %s
Note
PARAMETERS:
%s: class method
%s: function name
MESSAGE:
CP_CRIT_TALK2_EVTHNDLR: %s: failed to install Talk2 event handler %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: status string
MESSAGE:
CP_CRIT_TRC_HDR: %s: failed to create trace header file (/tmp permissions?)
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_ADD_CHGHNDLR: %s: failed to add change handler
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_ADD_CLIENT: %s: failed to add client
Note
PARAMETERS:
%s: class method
MESSAGE:
CP_ERR_ADD_MDLSIGNAL: %s: failed to add MDL signal %s to engine-mdl signal table
Note
PARAMETERS:
%s: class method
%s: mdl signal Id
MESSAGE:
CP_ERR_ADD_MEAS: %s: failed to add meas failed for %s
Note
PARAMETERS:
%s: class method
%s: dest
MESSAGE:
CP_ERR_ALLOC_MDL_TIMERS: %s Failed to allocate MDL timers for process %s process id %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: MDL process name
%d: MDL process id
MESSAGE:
CP_ERR_ALLOC_MEM: %s Failed to alloc memory for class %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: class name
MESSAGE:
CP_ERR_ASGN_BC: %s: failed to assign, bearChan %s has no VSF
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_AUDIT_CONGST: %s: auditLoop application is congested
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_AUDIT_SCHEDULE: %s: auditLoop application is scheduled again
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_AUEP: %s: failed to audit the end point
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_BAD_CALLSIDE: %s: bad callside %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: callside
MESSAGE:
CP_ERR_BAD_CKSUM: %s: bad checksum for %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: file name
MESSAGE:
CP_ERR_BAD_STREAM: %s: bad stream
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_BC_NOT_FOUND: %s Failed to find bear channel
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_BOXNUM: %s: failed to get boxnum: none <= %d
Note
PARAMETERS:
%s: class::method
%d: max boxnum
MESSAGE:
CP_ERR_BUILD_MDL_MSG: %s Failed to build MDL message
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_CALL_SCHEDULED_TWICE: %s Call got scheduled twice
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_CALL_TERM_ABNORMALLY: %s Call has terminated abnormally %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: terminating cause
MESSAGE:
CP_ERR_CHAN_MAP_IE_NOT_SUPPORTED: %s Channel Map IEs not supported
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_CHAN_NOT_ACQ: %s the channel is not acquired
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_CREATE_CALL_FAILED: %s:Could not create a new call
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_CREATE_STBY_CALL_INSTANCE: %s Failed to create standby call instance
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_CRT_ASP: %s: failed to create auxSigPath
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_CRT_BC_EXISTS: %s: failed to create bearChan %s, already exists
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_CRT_BC_VSF: %s: failed to create bearChan %s, no VSF
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_CRT_CABLE: %s: failed to create cable %C, null VSF %C
Note
PARAMETERS:
%s: class::method
%C: cable ID (component id)
%C: VSF ID (component id)
MESSAGE:
CP_ERR_CRT_CALL: %s: failed to create call on %C/%x
Note
PARAMETERS:
%s: class::method
%C: pointCode
%08x: bearChan
MESSAGE:
CP_ERR_CRT_MEAS: %s: failed to create meas
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_CRT_SIGPATH: %s: failed to create sigPath %C
Note
PARAMETERS:
%s: class::method
%C: sigPath ID
MESSAGE:
CP_ERR_CRT_SPAN: %s: failed to create span %x, sigPath %C
Note
PARAMETERS:
%s: class::method
%x: span ID
%C: sigPath ID
MESSAGE:
CP_ERR_CRT_VP: %s: failed to create VP %x
Note
PARAMETERS:
%s: class::method
%x: VP Id
MESSAGE:
CP_ERR_CXN_EXIST: %s: %s connection already exists
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: type of connection
MESSAGE:
CP_ERR_DD_RETRV: %s: failed to retrieve a record of record type %d key %s from dynamic data store
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: record type
%s: key
MESSAGE:
CP_ERR_DEL_CHGHNDLR: %s: failed to delete change handler
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_DE_REG_WRITE_SERVICE: %s Failed to de-register write service
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_DUP_ENDPOINT: %s: duplicate endpoint %s, %s
Note
DESCRIPTION:
The specified bearer channel has the same endpoint as a previously specified one.
PARAMETERS:
%s: class::method
%s: existing bearChan
%s: bearChan with dup endpoint
MESSAGE:
CP_ERR_ENABLE_ACCESS: %s: cannot enable engine system connection data access
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_ENCODE_VSF: %s: failed to encode msg to VSF, cxn %d, endpoint %s
Note
PARAMETERS:
%s: class::method
%d: cxn ID
%s: endpoint ID
MESSAGE:
CP_ERR_ENQUEUE_FAILED_IN_CALL: %s: Failed to queue a command into %s queue of call %d
Note
PARAMETERS:
%s: class::method
%s: queue name
%d: call id
MESSAGE:
CP_ERR_FILL_EXIST: %s: handleStartTrace(Abnormal) file exists
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_FIND_BC: %s: cannot find bearChan %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: bearChan ID
MESSAGE:
CP_ERR_FIND_BC_CALL: %s: Call %d asscociated with the bearer channel %s cannot be found in the call map.
Note
PARAMETERS:
%s: class::method
%d: call id
%s: bearer channel identifier (sigpath id/span id/CIC)
MESSAGE:
CP_ERR_FIND_CABLE: %s: failed to find cable with slot %u, port %u
Note
PARAMETERS:
%s: class::method
%u: slot
%u: port
MESSAGE:
CP_ERR_FIND_CABLE_BTWN: %s: failed to find cable between %C - %C
Note
PARAMETERS:
%s: class::method
%C: VSF ID
%C: VSF ID
MESSAGE:
CP_ERR_FIND_CABLE_ID: %s: failed to find cable %C/%C
Note
PARAMETERS:
%s: class::method
%C: VP ID
%C: cable ID
MESSAGE:
CP_ERR_FIND_CALL: %s: failed to find call on %C/%x
Note
PARAMETERS:
%s: class::method
%C: pointCode
%x: bearChan
MESSAGE:
CP_ERR_FIND_CALL_FOR_CALLID: %s: cannot find call for call id %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: call id
MESSAGE:
CP_ERR_FIND_CALL_PROCESS: %s: Could not obtain process %d in call %d.
Note
PARAMETERS:
%s: class::method
%d: mdl process id
%d: signal name
MESSAGE:
CP_ERR_FIND_CDR_FUNC: %s: failed to find cdr function for tagId %d
Note
PARAMETERS:
%s: class::method
%d: tag id
MESSAGE:
CP_ERR_FIND_CLIENT: %s: failed to find client
Note
PARAMETERS:
%s: class method
MESSAGE:
CP_ERR_FIND_CXN1: %s: failed to find cxn %u
Note
PARAMETERS:
%s: class::method
%s: cxn ID
MESSAGE:
CP_ERR_FIND_CXN2: %s: failed to find cxn %u, %s
Note
PARAMETERS:
%s: class::method
%s: cxn ID
%s: notification parms
MESSAGE:
CP_ERR_FIND_CXN_BC: %s: failed to find cxn with bearChan %s
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_FIND_CXN_CALL: %s: failed to find cxn with call ID %s
Note
PARAMETERS:
%s: class::method
%s: VSF data
MESSAGE:
CP_ERR_FIND_CXN_REQID: %s: failed to find cxn from req ID %u %s
Note
PARAMETERS:
%s: class::method
%u: request ID
%s: VSF ID
MESSAGE:
CP_ERR_FIND_ENUM_ID: %s: failed to find enum id %s
Note
PARAMETERS:
%s: class::method
%s: enum id
MESSAGE:
CP_ERR_FIND_ENUM_TAG: %s: failed to find enum tag %s
Note
PARAMETERS:
%s: class::method
%s: enum tag
MESSAGE:
CP_ERR_FIND_MASTER_DATA: %s: No master data saved in call %d for the signal %s; hence not requeuing the signal
Note
PARAMETERS:
%s: class::method
%d: call id
%s: signal name
MESSAGE:
CP_ERR_FIND_MEAS: %s Failed to find measurement %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: measurement name
MESSAGE:
CP_ERR_FIND_RANGE: %s: failed to find range for %s
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_FIND_SIGPATH: %s: failed to find the sigPth %C in usepool as it should be
Note
PARAMETERS:
%s: class method
%C: sigPath Id
MESSAGE:
CP_ERR_FIND_TXN: %s: failed to find txn %u
Note
PARAMETERS:
%s: class::method
%u: txn ID
MESSAGE:
CP_ERR_FIND_VC: %s: failed to find virtChan %C/%u
Note
PARAMETERS:
%s: class::method
%C: sigPath
%u: virtChan
MESSAGE:
CP_ERR_GET_CALL_PROC: %s: failed to find call control process %d in call %d
Note
PARAMETERS:
%s: class method
%d: call side
%d: call Id
MESSAGE:
CP_ERR_GET_CC: %s: cannot get call control for %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: call side
MESSAGE:
CP_ERR_GET_CDR_MGR: %s: failed to get CDR manager
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_GET_CHPT_CONN_DATA: %s Failed to populate Ans connection data
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_GET_EXTDATA: %s: failed to get external function data
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_GET_MDL_DIR: %s: failed to get MDL protocol dir %s %s
Note
PARAMETERS:
%s: class::method
%s: facility
%s: reason
MESSAGE:
CP_ERR_GET_MDL_PROC_FROM_CALL: %s Failed to get MDL process id %d from cmgCall object
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MDL process id = mdlProcIdTP
MESSAGE:
CP_ERR_GET_NEW_CALL: %s Failed to get new call
Note
PARAMETERS:
%s: either class::method: or class::method: call <call id>
MESSAGE:
CP_ERR_GET_OCC: %s: cannot get originating call control process
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_GET_OVLD: %s: failed to get overload condition
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_GET_PA: %s: failed to get protocol adapter for sigPath %C
Note
PARAMETERS:
%s: class::method
%C: sigPath ID
MESSAGE:
CP_ERR_GET_PARM: %s: failed to get parameter id
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_GET_PROC: %s: failed to get orig process for call %d
Note
PARAMETERS:
%s: class::method
%d: call ID
MESSAGE:
CP_ERR_GET_PROP: %s: failed to get property value
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_GET_SIGPATH: %s: failed to get sigPath for call %d
Note
PARAMETERS:
%s: class::method
%d: call ID
MESSAGE:
CP_ERR_GET_SIGPATH_FOR_CALLSIDE: %s: failed to get sigPath for callside %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: callside
MESSAGE:
CP_ERR_GET_TCC: %s: cannot get terminating call control process
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_IE_NOT_FOUND: %s CALL_STATE information element is not found
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_INCON_SLAVES: %s: inconsistent slave values: %d cics > %d bits
Note
PARAMETERS:
%s: class::method
%d: number of cics
%d: number of bits
MESSAGE:
CP_ERR_INIT: %s: failed to initialize %s
Note
PARAMETERS:
%s: class method
%s: class name
MESSAGE:
CP_ERR_INIT_CHPT_STBY_CALL_LEG: %s Failed to init %s call leg
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: ORIG or TERM call side
MESSAGE:
CP_ERR_INIT_MDL_INF: %s: failed to initialize mdl informer
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_INIT_MDL_PROC: %s Failed to initialize MDL for process %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: process name
MESSAGE:
CP_ERR_INIT_MDO: %s: failed to init conversion def %s from MDO file %s
Note
PARAMETERS:
%s: class::method
%s: protocol name
%s: protocol file
MESSAGE:
CP_ERR_INS1: %s: failed to insert %s
Note
PARAMETERS:
%s: class::method
%s: object that can't be inserted
MESSAGE:
CP_ERR_INS2: %s: failed to insert, null %s
Note
PARAMETERS:
%s: class::method
%s: missing object
MESSAGE:
CP_ERR_INSERT_CDR_FUNC: %s: failed to insert CDR function
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_INSERT_OBJ_IN_MAP: %s Failed to insert key %d in MAP %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MAP key
%s: MAP table name
MESSAGE:
CP_ERR_INSERT_PROC: %s: Failed to insert cmgCallRefId into processedProcs, size = %d
Note
PARAMETERS:
%s: class::method
%d: proc size
MESSAGE:
CP_ERR_INSTALL_HDLR: %s Failed to install Call Generator event handler %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: state string
MESSAGE:
CP_ERR_INV_ARG: %s: invalid args
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_INV_ARG_FOR_TAG: %s: invalid args for tagId %d
Note
PARAMETERS:
%s: class::method
%d: tag ID
MESSAGE:
CP_ERR_INV_BC_IE: %s Bear Chan IE has invalid length
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_INV_CALL_DIR: %s Invalid call direction
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_INV_COMM: %s Invalid command %d for target %d
Note
PARAMETERS:
%s: application identifier
%d: command type
%d: target type
MESSAGE:
CP_ERR_INV_DATA_LEN: %s Invalid MDL data length %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MDL data len
MESSAGE:
CP_ERR_INV_ENUM_TYPE: %s Invalid enum type %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MDL data len
MESSAGE:
CP_ERR_INV_FUNC: %s: invalid function code
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_INV_GWY: %s invalid gateway %C
Note
PARAMETERS:
%s: application identifier
%C: gateway compid
MESSAGE:
CP_ERR_INV_IDU_PARM: %s: %s %s
Note
PARAMETERS:
%s: class method
%s: parameter name
%s: error reason
MESSAGE:
CP_ERR_INV_LCM: %s: invalid LCM checksum (CC version)
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_INV_LEGID: %s: incorrect LegId value
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_INV_MDL_FUNC_GROUP: %s invalid MDL function group %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MDL function group id
MESSAGE:
CP_ERR_INV_MDL_PROC: %s Invalid MDL process id %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: process id
MESSAGE:
CP_ERR_INV_MDL_TAG: %s Invalid MDL tag %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MDL tag id
MESSAGE:
CP_ERR_INV_MSG_LEN: %s Invalid message length %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: message length in bytes
MESSAGE:
CP_ERR_INV_MSG_TYPE: %s Invalid message type %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: message type
MESSAGE:
CP_ERR_INV_NULL_SIGPATH: %s: invalid null sigPath %C
Note
PARAMETERS:
%s: class::method
%C: sigPath ID
MESSAGE:
CP_ERR_INV_PARM: %s: invalid parameter %d %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: parameter
%s: cause
MESSAGE:
CP_ERR_INV_PARMS: %s Invalid parameter %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: parameter id
MESSAGE:
CP_ERR_INV_PARM_COUNT: %s Invalid number of parameter %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: number of parameter
MESSAGE:
CP_ERR_INV_PDUTP: %s: invalid PDU type from sigPath %C
Note
PARAMETERS:
%s: class::method: <call<callid>>
%C: sigPath
MESSAGE:
CP_ERR_INV_PROP: %s: invalid property value %s for %s
Note
PARAMETERS:
%s: class::method
%s: property value
%s: sigPath ID
MESSAGE:
CP_ERR_INV_RESTART_IND_IE: %s: restart indicator IE has invalid length
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_INV_SERVICE_STATE: %s: invalid service state %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: channel service state
MESSAGE:
CP_ERR_INV_SIGPATH: %s Invalid sigPath
Note
PARAMETERS:
%s: application identifier
MESSAGE:
CP_ERR_INV_SLAVE: %s: invalid slave %x not in this group reset (%s)
Note
PARAMETERS:
%s: class::method
%x: CIC
%s: slave range
MESSAGE:
CP_ERR_INV_SPAN_ID: %s Invalid spanid %d
Note
PARAMETERS:
%s: application identifier
%d: spanid
MESSAGE:
CP_ERR_INV_STOP_COMMAND: %s bad status at event type = %d, event sub type = %d
Note
PARAMETERS:
%s: application identifier
%d: event type
%d: event sub type
MESSAGE:
CP_ERR_INV_TAG_COUNT: %s Invalid MDL tag count %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MDL tag count
MESSAGE:
CP_ERR_INV_TARGET: %s Invalid target %d for command %d
Note
PARAMETERS:
%s: application identifier
%d: target type
%d: command type
MESSAGE:
CP_ERR_INV_TXN: %s: invalid txn %u is not a cxn
Note
PARAMETERS:
%s: class::method
%u: txn ID
MESSAGE:
CP_ERR_LINK_MDL_PROC_TO_CALL: %s Failed to link MDL process to %s call context
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: ORIG or TERM call side
MESSAGE:
CP_ERR_LOAD_MDL: %s: failed to load MDL module %s from %s
Note
PARAMETERS:
%s: class::method: <call<callid>>
%s: process name
%s: protocol file name
MESSAGE:
CP_ERR_LOAD_TBL: %s: failed to load %s from %s
Note
PARAMETERS:
%s: class::method
%s: table name
%s: file name
MESSAGE:
CP_ERR_MARKED_FOR_DEL_CALL: %s Call is marked for delete
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_MDL_MSG: %s: Invalid MDL message %s
Note
PARAMETERS:
%s: group ID, message ID and error status
%d: groupID (defined in MDL Engine Interface)
MESSAGE:
CP_ERR_MDL_MSG_PARSE: %s: message parse failed, call ID %d
Note
DESCRIPTION:
Error message that engine cannot parse a message from MDL.
PARAMETERS:
%s: class::method
%d: call ID
MESSAGE:
CP_ERR_MDL_OBJ_PTR_IS_NULL: %s object ptr %s is NULL for process %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: cmgLcmProcCxt.m_lcmDef
%s: MDL process name
MESSAGE:
CP_ERR_MISMATCH_SIGPATH: %s Mismatch sigpath data are %C and %C
Note
PARAMETERS:
%s: application identifier
%C: sigpath compid
%C: sigpath compid
MESSAGE:
CP_ERR_MSG_TOO_LONG: %s Message is too long
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_NO_ASCID: %s: Remote ASC ID not set
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_NO_MATE: %s: failed to set call using, %s has no mate
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_NO_TRK_IN_GRP: %s:There is no trunk in trunk group %u
Note
PARAMETERS:
%s: class::method
%u: trunk group Id
MESSAGE:
CP_ERR_NULL_CALLOBJ: %s: null call object
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_NULL_CALL_PROC: %s: null process found in the map for call reference %d
Note
PARAMETERS:
%s: class method
%d: call reference id
MESSAGE:
CP_ERR_NULL_CXN: %s: null connection for Virtual Path %C
Note
DESCRIPTION:
Error message that this virtual path has no associated connection.
PARAMETERS:
%s: class::method
%C: Virtual Path ID
MESSAGE:
CP_ERR_NULL_PDU: %s: null PDU
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_OBJ_NOT_FOUND_IN_MAP: %s Failed to find key %d in MAP %s
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: MAP key
%s: MAP table name
MESSAGE:
CP_ERR_OBJ_PTR_IS_NULL: %s object ptr %s is NULL
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: cmgLcmProcCxt.m_lcmDef
MESSAGE:
CP_ERR_OPEN_FILE: %s: failed to open file, errno %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: errno
MESSAGE:
CP_ERR_PAIR: %s: %s for sigpath %C
Note
PARAMETERS:
%s: class method
%s: pair state
%C: sigPathId
MESSAGE:
CP_ERR_PARSE_SGCP: %s: failed to parse SGCP: %s
Note
PARAMETERS:
%s: class::method
%s: command or response string
MESSAGE:
CP_ERR_PARSE_SLOT: %s: failed to parse slot/port from %s for bearChan %s
Note
PARAMETERS:
%s: class::method
%s: physical interface
%s: bearChan ID
MESSAGE:
CP_ERR_PDUMSG: %s: Error PDU message sent to %C
Note
PARAMETERS:
%s: class::method: <call<callid>>
%C: sigPath
MESSAGE:
CP_ERR_PDU_LONG: %s: PDU message too long
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_POPULATE_ANS_CHPT_CALL_LEG: %s Failed to populate %s ans checkpoint call leg
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: ORIG or TERM call side
MESSAGE:
CP_ERR_POPULATE_ANS_CHPT_DATA: %s Failed to populate ans call chpt msg
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_PRINT_CALL: %s: failed to print call %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: callId
MESSAGE
CP_ERR_PRINT_MDL_MSG: %s: failed to print MDL:
MESSAGE:
groupID %d, msgID %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: groupID (defined in MDL Engine Interface)
%d: messageID (defined in MDL Engine Interface)
MESSAGE:
CP_ERR_PROC_MSG: %s: failed to process MDL message %s
Note
PARAMETERS:
%s: class::method
%s: message type
MESSAGE:
CP_ERR_QUERY: %s: data access query failed: %s
Note
PARAMETERS:
%s: class::method
%s: returned error message from the query
MESSAGE:
CP_ERR_READ_BUF: %s: failed to read null msg buf, txn %d
Note
PARAMETERS:
%s: class::method
%d: txn ID
MESSAGE:
CP_ERR_READ_PARM: %s: failed to read parameter from extData
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_REG_EVT: %s: failed to register events
Note
PARAMETERS:
%s: class method
MESSAGE:
CP_ERR_REG_PIPE_EVT: %s Failed to register communication event %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: communication event id
MESSAGE:
CP_ERR_REG_READ_SERVICE: %s Failed to register read service
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_REG_SVC: %s: failed to register %08x for service %s
Note
PARAMETERS:
%s: class::method
%08x: object
%s: service name
MESSAGE:
CP_ERR_REG_TBL: %s: failed to register for %s table
Note
PARAMETERS:
%s: class::method
%s: table name
MESSAGE:
CP_ERR_REG_WRITE_SERVICE: %s Failed to register write service
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_REL_BW: %s: failed to release bandwidth, call (%lu) + avail (%lu) > max
Note
PARAMETERS:
%s: class::method
%lu: call bandwidth
%lu: available bandwidth
MESSAGE:
CP_ERR_RTRV_HDL_DBS: %s: failed to retrieve handle to engDatabase
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_RTRV_HDL_MDL_INF: %s: failed to retrieve handle to rmgMDL_Informer
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_RTRV_HDL_MDL_PROC: %s: failed to retrieve handle to cmgMDLProcCxt
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_SAVE_TCC: %s: failed to save TCC info for call %d
Note
PARAMETERS:
%s: class::method
%d: call ID
MESSAGE:
CP_ERR_SEND_ANS_MSG_TO_REP: %s Failed to send ans chpt msg to replicator
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_SEND_CALLEVT: %s: failed to send message into call pointCode=%C, CIC=%x
Note
PARAMETERS:
%s: class method
%C: pointCode
%x: CIC
MESSAGE:
CP_ERR_SEND_CU: %s: failed to send message, CU has no ID for cxn %d
Note
PARAMETERS:
%s: class::method
%d: cxn ID
MESSAGE:
CP_ERR_SEND_MSG: %s: failed to send message into call for %C
Note
PARAMETERS:
%s: class::method: <call<callid>>
%C: sigPath
MESSAGE:
CP_ERR_SEND_MSG_TO_MDL_PROC: %s Failed to send message to MDL process
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_SEND_MSG_TO_PROC: %s: failed to send message into mdl process %d of call %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: process id
%d: call id
MESSAGE:
CP_ERR_SEND_MSG_TO_REP: %s Failed to send Evt %d and EvtSubType %d to replicator
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: XE Event id
%d: XE Event Sub Type id
MESSAGE:
CP_ERR_SEND_VSF: %s: failed to send msg to VSF, too long (%d), txn %d
Note
PARAMETERS:
%s: class::method
%d: length
%d: txn ID
MESSAGE:
CP_ERR_SET_ARG: %s: failed to set args
Note
PARAMETERS:
%s: class::method: <call<callid>>
MESSAGE:
CP_ERR_SET_EVT_PARMS: %s: failed to set event parms for cxn %d, no req events
Note
PARAMETERS:
%s: class::method
%d: cxn ID
MESSAGE:
CP_ERR_SET_INUSE: %s: failed to set call using, %s in use by call %d
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
%d: call ID
MESSAGE:
CP_ERR_SET_MATED: %s: failed to set call using, %s already mated
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_SET_PROP: %s: failed to set property value
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_SIGNAL_MISMATCH: %s:Discrepancy in the signals (%s) stored in the master data and the signal command; hence not requeuing the signal
Note
PARAMETERS:
%s: class::method
%s: signals that are not matching
MESSAGE:
CP_ERR_SIGPATH_NOTAVAIL: %s sigpath %C not available
Note
PARAMETERS:
%s: class::method
%C: sigpath component id
MESSAGE:
CP_ERR_SIG_CALL: %s: failed to signal call %d
Note
PARAMETERS:
%s: class::method
%d: call ID
MESSAGE:
CP_ERR_START_MDL_PROC: %s Failed to start MDL process %s process id %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%s: MDL process name
%d: MDL process id
MESSAGE:
CP_ERR_STREAM: %s: stream error
Note
PARAMETERS:
%s: class method
MESSAGE:
CP_ERR_TEMP_LOGMSG: %s
Note
PARAMETERS:
%s: temporary placeholder string for future defined message
MESSAGE:
CP_ERR_UNEX_EVT: %s: unexpected event %s
Note
PARAMETERS:
%s: class::method
%s: event ID
MESSAGE:
CP_ERR_UNEX_MSG: %s: unexpected msg type %s
Note
PARAMETERS:
%s: class::method
%s: msg type
MESSAGE:
CP_ERR_UNEX_RESP1: %s: unexpected VSF response %d
Note
PARAMETERS:
%s: class::method
%d: response code
MESSAGE:
CP_ERR_UNEX_RESP2: %s: unexpected response from VSF, cxn %d, state %d
Note
PARAMETERS:
%s: class::method
%d: cxn ID
%d: state
MESSAGE:
CP_ERR_UNEX_TRAN: %s: unexpected transition %d
Note
PARAMETERS:
%s: class::method
%d: state transition
MESSAGE:
CP_ERR_UNKN_BLKTP: %s: unknown block type %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: blocktype
MESSAGE:
CP_ERR_UNKN_CALLTYPE: %s: unknown call type %d
Note
PARAMETERS:
%s: class::method
%d: call type
MESSAGE:
CP_ERR_UNKN_CHAN_MGMT: %s: unknown chan mgmt type %d
Note
PARAMETERS:
%s: class::method
%d: chan mgmt type
MESSAGE:
CP_ERR_UNKN_CMD1: %s: unknown cmd %d
Note
PARAMETERS:
%s: class::method
%d: command
MESSAGE:
CP_ERR_UNKN_CMD2: %s: unknown command: %s
Note
PARAMETERS:
%s: class::method
%s: command
MESSAGE:
CP_ERR_UNKN_COMPTYP: %s: unknown compType in cxnSigPath %C
Note
PARAMETERS:
%s: class::method
%C: cxnSigPath ID
MESSAGE:
CP_ERR_UNKN_CXN: %s: unknown cxn type %d
Note
PARAMETERS:
%s: class::method
%d: cxn type
MESSAGE:
CP_ERR_UNKN_MEAS: %s: unknown meas %s for sigPath %C
Note
PARAMETERS:
%s: class::method
%s: measurement
%C: sigPath ID
MESSAGE:
CP_ERR_UNKN_MSGTYPE: %s: unknown message type %d received
Note
PARAMETERS:
%s: class method
%d: message Type
MESSAGE:
CP_ERR_UNKN_MSG_MDL: %s: unknown MDL message group %d, message type %d
Note
PARAMETERS:
%s: class::method
%d: message group
%d: message type
MESSAGE:
CP_ERR_UNKN_MSG_VSF: %s: unknown msg %d from %s
Note
PARAMETERS:
%s: class::method
%d: msg code
%s: msg source
MESSAGE:
CP_ERR_UNKN_PROTO_FAM: %s: unknown protocol family for %s
Note
PARAMETERS:
%s: class::method
%s: protocol name
MESSAGE:
CP_ERR_UNKN_PROTO_SIGPATH: %s: unknown protocol %s for sigPath %C
Note
PARAMETERS:
%s: class::method
%s: proto name
%C: sigPath ID
MESSAGE:
CP_ERR_UNKN_QUERY: %s: unknown data access query %s
Note
PARAMETERS:
%s: class::method
%s: access query name
MESSAGE:
CP_ERR_UNKN_REQTP: %s: unknown request type %d
Note
PARAMETERS:
%s: class::method: <call<callid>>
%d: request type
MESSAGE:
CP_ERR_UNKN_SEL_ALGO: %s: unknown select algorithm %s for trunkGrp %08x
Note
PARAMETERS:
%s: class::method
%s: algorithm
%08x: trunkGroup ID
MESSAGE:
CP_ERR_UNKN_TRUNKGRP: %s: unknown trunkGrp type %s for sigPath %C
Note
PARAMETERS:
%s: class::method
%s: trunkGroup type
%C: sigPath ID
MESSAGE:
CP_ERR_UNSPEC_PARM: %s: unspecified config parameter %s, status %s
Note
PARAMETERS:
%s: class method
%s: parameter name
%s: status
MESSAGE:
CP_ERR_UN_MATCHING_PA: %s Un-matching protocol adapter
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_ERR_UPD_TBL: %s: failed to update table %s
Note
PARAMETERS:
%s: class::method
%s: table name
MESSAGE:
CP_ERR_UPD_TBL_PURGE: %s: failed to update tables, purge failed
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_ERR_VAL_BC: %s: failed to validate bearChan %s
Note
PARAMETERS:
%s: class::method
%s: bearChan ID
MESSAGE:
CP_ERR_VAL_DPC: %s: failed to validate DPC %C
Note
PARAMETERS:
%s: class::method
%C: DPC ID
MESSAGE:
CP_ERR_VAL_SIGPATH: %s: failed to validate sigPath %C
Note
PARAMETERS:
%s: class::method
%C: sigPath ID
MESSAGE:
CP_ERR_VIRTCHAN_NONDPNSS: %s: virtual chan for non-DPNSS sigpath %C
Note
PARAMETERS:
%s: class method
%C: sigpath Id
MESSAGE:
CP_ERR_VNET_GT_SIGPATH: %s vnet %s > max length 4 for sigpath %C
Note
PARAMETERS:
%s:
%s:
%C: sigpath
MESSAGE:
CP_ERR_VNET_TBL_INDEX: %s vnet tbl index %d, max 9999 for sigpath %C
Note
PARAMETERS:
%s:
%s:
%C: sigpath
MESSAGE:
CP_ERR_WRITE_SIGPATH: %s: failed to write event to sigPath %C
Note
PARAMETERS:
%s: class::method
%C: sigPath ID
MESSAGE:
CP_INFO_ABORT_CMD: Aborting the following command %s
Note
PARAMETERS:
%s: string for command
MESSAGE:
CP_INFO_AUDIT_IN_PROGRESS: %s: audit already in progress
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_INFO_AUDIT_SYNC: %s: Audit: VSC and EndOffice not in sync for PC=%s, CIC=%d
Note
PARAMETERS:
%s: class::method
%s: point code name
%d: chan ID
MESSAGE:
CP_INFO_CHANGE_DIALPLAN: Changed dial plan for %s
Note
PARAMETERS:
%s: customer Id
MESSAGE:
CP_INFO_CHAN_STATE: Mismatch in channel state, %s, span %d, channel %d
Note
PARAMETERS:
%s: channel state in Media Gateway and media gateway controller
%d: spanID
%d: channel number
MESSAGE:
CP_INFO_CRT_BCS: created %d bearChans
Note
PARAMETERS:
%d: number of bearChans
MESSAGE:
CP_INFO_CRT_BC_PAIRS: created %d bearChan pairs
Note
PARAMETERS:
%d: number of bearChan pairs
MESSAGE:
CP_INFO_CRT_BC_SIGPATH: created %d bearChans for sigPath %C
Note
PARAMETERS:
%d: num bearChans
%C: sigPath ID
MESSAGE:
CP_INFO_CRT_CABLE: created %d cables
Note
PARAMETERS:
%d: number of cables
MESSAGE:
CP_INFO_CRT_SIGPATH: created %d sigPaths
Note
PARAMETERS:
%d: number of sigPaths
MESSAGE:
CP_INFO_CRT_TRUNKGRP: created %d trunkGroups
Note
PARAMETERS:
%d: number of trunk groups
MESSAGE:
CP_INFO_CRT_VP: created %d VPs
Note
PARAMETERS:
%d: number of VPs
MESSAGE:
CP_INFO_CXNS: %s: connection info: %s
Note
PARAMETERS:
%s: class::method
%s: connection info
MESSAGE:
CP_INFO_DUMP_DATA: %s
Note
PARAMETERS:
%s: data string
MESSAGE:
CP_INFO_FIND_EXTFUNC: %s:could not find extfunc data entry for %d in call %d
Note
PARAMETERS:
%s: class::method
%d: external function id
%d: call id
MESSAGE:
CP_INFO_FINISH_AUDIT: Audit finished
Note
MESSAGE:
CP_INFO_GRPSERV_COUNT: %s: reached max count for checking group service complete
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_INFO_INIT_CMD: command initialized %s
Note
PARAMETERS:
%s: info string
MESSAGE:
CP_INFO_INIT_HDLR: %s initialized
Note
PARAMETERS:
%s: class method
MESSAGE:
CP_INFO_LOAD_PROTO: loaded %s from file %s
Note
PARAMETERS:
%s: protocol name
%s: filename
MESSAGE:
CP_INFO_MDLSIGNAL_TBL: Build engine-mdl table: %d ASC signals
Note
PARAMETERS:
%d: number of signals
MESSAGE:
CP_INFO_PROCESS_NOT_EXIST: %s:Process %d in call %d no longer exists, so trashing the timer expiration event
Note
PARAMETERS:
%s: class::method
%d: Process
%d: callId
MESSAGE:
CP_INFO_RESYNC_RESP: %s: RESYNC RESP does not match previous RESYNC REQ sig path %C, span %d, discard message
Note
PARAMETERS:
%s: class::method
%C: sigPathID
%d: spanID
MESSAGE:
CP_INFO_RMG_INIT: resource mgr init OK, local ASP ID = %08x
Note
PARAMETERS:
%08x: ASP ID
MESSAGE:
CP_INFO_RUNMODE: running in %s mode
Note
PARAMETERS:
%s: SWITCHED or NAILED-UP
MESSAGE:
CP_INFO_SET_ALARM: Alarm set: sigPath=%C, %s
Note
This log is generated to further specify the scope of the alarm generated for the signalling path noted.
span=<span>
bc=<bearer channel>
alarmIndex=nnn
PARAMETERS:
%C: component name of the SigPath
%s: span, bearer channel, and alarmIndex of alarm
MESSAGE:
CP_INFO_SSC_EVENT: %s SSC FROM sigState %s TO sigTransState %s
Note
PARAMETERS:
%s: application log identifier
%s: current sigpath state
%s: transition sigpath state
MESSAGE:
CP_INFO_START_AUDIT: Audit started
Note
MESSAGE:
CP_INFO_START_TRACE: Start trace: trace log file %s%s
Note
PARAMETERS:
%s:trace directiory
%s:trace filename
MESSAGE:
CP_INFO_STOP_AUDIT: Audit stopped
Note
MESSAGE:
CP_INFO_STOP_TRACE: Stop trace: sigPath %C
Note
PARAMETERS:
%C: sigPathId
MESSAGE:
CP_INFO_TEMP_LOGMSG: %s
Note
PARAMETERS:
%s: temporary placeholder string for future defined message
MESSAGE:
CP_INFO_UNSPEC_PARM: unspecified config param %s, will default
Note
PARAMETERS:
%s: parameter name
MESSAGE:
CP_TRACE_PRO_HEX_MSG: %s
Note
PARAMETERS:
%s: protocol message in hex format
MESSAGE:
CP_TRACE_STOP_COMMAND: %s event type = %d, event sub type = %d
Note
PARAMETERS:
%s: application identifier
%d: event type
%d: event sub type
MESSAGE:
CP_WARN_AUDIT: Cannot start audit %s
Note
PARAMETERS:
%s: reason
MESSAGE:
CP_WARN_BAD_ENUM_VALUE: %s: enum value is out of bound: enum tag =%s, enum value= %d
Note
PARAMETERS:
%s: class::method
%s: enum tag
%d: enum value
MESSAGE:
CP_WARN_BC_NOT_CONFG: The bearChan for SigPath %C, span %lx, CIC %d is not configured
Note
PARAMETERS:
%C: sigPathID
%lx: spanID
%d: circuitID
MESSAGE:
CP_WARN_CANT_CHG_AUD_STATE: %s cannot change audit state from %d to %d
Note
PARAMETERS:
%s: class::method
%d: old state
%d: new state
MESSAGE:
CP_WARN_CONGEST: %s
Note
PARAMETERS:
%s: congestion info string
MESSAGE:
CP_WARN_FIND_BC: cannot find bearChan %s
Note
PARAMETERS:
%s: beachChan Id
MESSAGE:
CP_WARN_FIND_CALL: %s cannot find call obj with callId %u
Note
PARAMETERS:
%s: class::method
%u: callId
MESSAGE:
CP_WARN_FIND_PROP: %s could not find property %s for resource %s
Note
PARAMETERS:
%s: class::method
%s: propName
%s: compName
MESSAGE:
CP_WARN_FIND_PROTO_ADAPTER: %s: %s protocol adapter corresponding sig path id %x is zero. So, the check point data is being ignored. May be the engine is initialized with no data and is not yet synched with the master.
Note
PARAMETERS:
%s: class::method
%s: Originating/Terminating side
%x: SigPathId
MESSAGE:
CP_WARN_FIND_SPAN: failed to find span %C/%x
Note
PARAMETERS:
%C: sigPath
%x: span
MESSAGE:
CP_WARN_GET_ALARM_CAT: %s: failed to get alarm category: %s
Note
PARAMETERS:
%s: class::method
%s: alarm category
MESSAGE:
CP_WARN_GET_PROT_ADAPTER: failed to get protocol adapter for sigPath %C
Note
PARAMETERS:
%s: class::method
MESSAGE:
CP_WARN_INSUFF_PA_ENTRIES: %s Insufficient protocol adapter entries
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
MESSAGE:
CP_WARN_INV_PARMS: %s Invalid parameter %d
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: parameter id
MESSAGE:
CP_WARN_NO_BC_INIT: no bearChans (re)initialized
Note
MESSAGE:
CP_WARN_PROT_ADP_DEL: %s The last protocol adapter for sigPath %C was deleted, entering into special logic
Note
PARAMETERS:
%s: class::method
%C: SigPath Id
MESSAGE:
CP_WARN_QUEUE_SIGN: %s [Thread:%d] This signal cannot be queued
Note
PARAMETERS:
%s: either class::method: or class::method: call <callid>
%d: XEThread
MESSAGE:
CP_WARN_REG_READ_SERVICE: failed to register read service %s
Note
PARAMETERS:
%s: service name
MESSAGE:
CP_WARN_REG_WRITE_SERVICE: failed to register write service %s
Note
PARAMETERS:
%s: service name
MESSAGE:
CP_WARN_RESYNC: Audit:: resync response not received for sp %C, span %lx
Note
PARAMETERS:
%C: sigPathID
%lx: spanID
MESSAGE:
CP_WARN_STATE_MISMATCH: %s: connection %s doesn't match response message %u
Note
DESCRIPTION:
Warning message that this connection is in an unexpected state when receiving a response from VSF.
PARAMETERS:
%s: class::method
%s: cxn ID, state
%u: msg type
MESSAGE:
CP_WARN_SYNC: %s: unable to send RESYNC REQ message for sigPath %C
Note
PARAMETERS:
%s: class::method
%C: sigpath Id
MESSAGE:
CP_WARN_SYNC_EP: Audit: Media Gateway Controller busy, EP idle for %C/%x/%x
Note
PARAMETERS:
%C: sigpath Id
%x: span Id
%x: bearChan Id
MESSAGE:
CP_WARN_TEMP_LOGMSG: %s
Note
PARAMETERS:
%s: temporary placeholder string for future defined message
MESSAGE:
CP_WARN_UNSPEC_PROP_PTCODE: unspecified %s for pointCode %C, default=%d
Note
PARAMETERS:
%s: property name
%C: pointCode ID
%d: default value
MESSAGE:
CP_WARN_UNSPEC_PROP_SIGPATH: unspecified %s for sigPath %C, default=%d
Note
PARAMETERS:
%s: property name
%C: sigPath ID
%d: default value
MESSAGE:
CP_WARN_UNSPEC_PROP_TRUNKGRP: unspecified %s for trunkGroup %d, default=%d
Note
PARAMETERS:
%s: property name
%d: trunkGroup ID
%d: default value
MESSAGE:
CP_WARN_WRITE_MSG: %s: can not write message to destination: Sigpath Id: %C
Note
PARAMETERS:
%s: class::method
%C: sigPath ID
MESSAGE:
CP_WARN_WRITE_SIGPATH: %s: cannot write to %C, state %u
Note
DESCRIPTION:
Warning message that this connection sigPath is not in service.
PARAMETERS:
%s: class::method
%C: sigPath ID
%u: sigPath state
MESSAGE:
ENV_CRIT_LOGSRVR_REREAD_REQUEST: Logger requested to reread component.dat
Note
DESCRIPTION:
The LogServer has been notified that it should reread the components file in order to pick up any updates that might have been applied so that the component id translation to MML name is accurate. This message is reserved for use by the log server only.
MESSAGE:
ENV_ERR_ADD_ALM_FAIL: compId %C: Failed to add/register alarm id %ld, category %lx
Note
PARAMETERS:
%C: MMLname[Component Id]
%ld: Alarm Id
%lx: Category
MESSAGE:
ENV_ERR_ADD_CHG_HDLR: Component Chg Hdlr Add failed - status = %d
Note
PARAMETERS:
%d: Error code
MESSAGE:
ENV_ERR_ALM_CAT_FAIL: Alarm Cat %s not found - Cannot %s Alarm for comp %s
Note
PARAMETERS:
%s: Alarm category
%s: `set' or `clear'
%s: Component name
MESSAGE:
ENV_ERR_ALM_COMP_FAIL: Component %s not found - Cannot %s Alarm Cat %s
Note
PARAMETERS:
%s: Component name
%s: `set' or `clear'
%s: Alarm category
MESSAGE:
ENV_ERR_BIND: bind() failed for UDP IPC %s, status %d
Note
PARAMETERS:
%s: Pathname
%d: Error code
MESSAGE:
ENV_ERR_CONNECT: bind() failed for UDP IPC %s, status %d
Note
DESCRIPTION:
Process has failed to open an IPC channel to another process in the system.
PARAMETERS:
%s: Pathname
%d: Error code
MESSAGE:
ENV_ERR_CRT_MUTEX: Failed to create XEMutex %s
Note
PARAMETERS:
%s: Name of the mutex
MESSAGE:
ENV_ERR_CRT_SHARED_MEM_KEY: Error creating shared memory key %s, status %d
Note
PARAMETERS:
%s: Key string
%d: Error code
MESSAGE:
ENV_ERR_CRT_SOCKET: Failed to create socket for IPC (%s), status %d
Note
DESCRIPTION:
The application failed to create an IPC socket. The application will exit.
PARAMETERS:
%s: Pathname
%d: Error code
MESSAGE:
ENV_ERR_DATA_MGR: Data manager init failed - %d (%s)
Note
PARAMETERS:
%d: Error code
%s: Error code converted to a string
MESSAGE:
ENV_ERR_EVT_DISPATCH: Event dispatcher init failed - status = %d
Note
PARAMETERS:
%d: Error code
MESSAGE:
ENV_ERR_EVT_SIZE: Event size %d different from buffer size %d
Note
PARAMETERS:
%d: Size of the event
%d: Size of the incoming buffer
MESSAGE:
ENV_ERR_FIFO_READ: Bad return from FIFO read: Status %d
Note
PARAMETERS:
%d: Error code
MESSAGE:
ENV_ERR_INTERNAL: Internal error: %s - %s
Note
PARAMETERS:
%s: Error description string
%s: Translation of XE Error code
MESSAGE:
ENV_ERR_IPC_CANT_PUT: IPC Open failed - Error code = %s Path %s
Note
PARAMETERS:
%s: Error code converted to string (strerr(errno))
%s: The FIFO that can't be accessed
MESSAGE:
ENV_ERR_IPC_FLAG: Failed to %s %s for IPC fd %d
Note
PARAMETERS:
%s: Set or Clear
%s: Description of the flag
%d: IPC File Descriptor
MESSAGE:
ENV_ERR_IPC_MODE: Failed to %s for %s, status %d
Note
PARAMETERS:
%s: Set or Clear + <what was not set/cleared>
%s: IPC pathname
%d: Error code
MESSAGE:
ENV_ERR_IPC_NULL_SVC: IPC Open failed - Null Service
Note
MESSAGE:
ENV_ERR_IPC_OPEN: IPC Open failed - Error code = %s Bad Path %s
Note
PARAMETERS:
%s: Error code converted to string (strerr(errno))
%s: The FIFO that can't be accessed
MESSAGE:
ENV_ERR_IPC_READ: IPC Read failed - Error code = %s Bad Path %s
Note
PARAMETERS:
%s: Error code converted to string (strerr(errno))
%s: The FIFO that can't be accessed
MESSAGE:
ENV_ERR_IPC_STAT: IPC Stat failed - Error code = %s Bad Path %s
Note
PARAMETERS:
%s: Error code converted to string (strerr(errno))
%s: The FIFO that can't be accessed
MESSAGE:
ENV_ERR_LICENSE: License could not be obtained - status = %d
Note
DESCRIPTION:
License could not be obtained.
PARAMETERS:
%d: Error code
MESSAGE:
ENV_ERR_LOAD_SW_TBL: Failed to load SW Layout table - Status: %d
Note
PARAMETERS:
%d: Error code
MESSAGE:
ENV_ERR_LOAD_TBL: Error loading objects from file to %s - Status %d (%s)
Note
PARAMETERS:
%s: Table name
%d: Error code
%s: Error code, converted to a string
MESSAGE:
ENV_ERR_MAIN_LOOP: regAppMainLoop() called more than once
Note
DESCRIPTION:
Application has called this routine more than once.
MESSAGE:
ENV_ERR_POLL: Bad return from poll() - status = %d
Note
DESCRIPTION:
System call failed - check the status to see what happened.
PARAMETERS:
%d:Value of errno
MESSAGE:
ENV_ERR_REG_SW_TBL: Failed to register SW Layout table - Status: %d
Note
PARAMETERS:
%d: Error code
MESSAGE:
ENV_ERR_REOPEN_SERVICE: Can't reopen default service %s
Note
PARAMETERS:
%s: Default service name
MESSAGE:
ENV_ERR_SIGACTION: Sigaction error for sig num %d, status = %d
Note
PARAMETERS:
%d: Signal number
%d: Value of errno
MESSAGE:
ENV_ERR_STREAMS: Formatted Streams not supported - service: %s
Note
PARAMETERS:
%s: Service name
MESSAGE:
ENV_ERR_STREAM_GETMSG: Getmsg failed on fd %d: Status %d (%s)
Note
PARAMETERS:
%d: File descriptor
%d: Error code
%s: Error code, converted to a string
MESSAGE:
ENV_ERR_STREAM_INV_MODULE: %s not a valid module - no modules pushed
Note
PARAMETERS:
%s: Name of the streams module
MESSAGE:
ENV_ERR_STREAM_IOCTL: IOCTL (NREAD) failed on fd %d: Status %d (%s)
Note
PARAMETERS:
%d: File descriptor
%d: Error code
%s: Error code, converted to a string
MESSAGE:
ENV_ERR_STREAM_OPEN: STREAMS open failed: %s: %s
Note
DESCRIPTION:
System failed to open a stream object. The reason for the failure is displayed.
PARAMETERS:
%s: Pathname that was being opened
%s: Reason for failure
MESSAGE:
ENV_ERR_STREAM_PUSH: Error pushing a Streams (%s) module: %s
Note
PARAMETERS:
%s: Pathname that was being opened
%s: Name of the streams module
MESSAGE:
ENV_ERR_THREAD_SPAWN: Failed to spawn thread: Detailed error info: %s
Note
DESCRIPTION:
System failed to create a thread.
PARAMETERS:
%s: Description of error (attr_init_failed, set_stacksize etc.)
MESSAGE:
ENV_ERR_UNKN_SERVICE: Unknown service type `%s' in configuration
Note
PARAMETERS:
%s': Service description
MESSAGE:
ENV_ERR_UNSUPPORTED_IPC: Unsupported IPC mechanism (%d) - service: %s
Note
PARAMETERS:
%d: IPC type
%s: Service name
MESSAGE:
ENV_TRACE_IPC_OPEN: Opened buffered FIFO %s (fd = %d)
Note
PARAMETERS:
%s: Name of the FIFO
%d: File Descriptor
MESSAGE:
ENV_WARN_ACCESS_PSET_FAIL: Can't access processor set %d: Errno = %d
Note
PARAMETERS:
%d: Processor set
%d: Unix Error code
MESSAGE:
ENV_WARN_BIND_PROCESSOR_FAIL: Failed to bind %s to processor %d - Status: %d
Note
PARAMETERS:
%s: Process/thread name (from SW_Layout.cfg table)
%d: Physical CPU number
%d: Error code
MESSAGE:
ENV_WARN_BIND_PSET_FAIL: Can't bind to processor set %d: Errno = %d
Note
PARAMETERS:
%d: Processor set
%d: Unix Error code
MESSAGE:
ENV_WARN_EXTRA_FIELDS: Extra fields in service.dat ignored: %s
Note
DESCRIPTION:
Service.dat file is configured incorrectly
PARAMETERS:
%s: List of information from service.dat
MESSAGE:
ENV_WARN_NO_SW_LAYOUT_REC: Failed to find first SW_Layout record
Note
MESSAGE:
ENV_WARN_REG_TBL: Failed to register component table with data mgr (%d)
Note
PARAMETERS:
%d: Error return from regTable routine
MESSAGE:
GEN_CRIT_ADD_SERVICE: Error adding %s service.
Note
PARAMETERS:
%s: name of the service
MESSAGE:
GEN_CRIT_ALLOCMEMFAIL: %s: Failed to allocate memory for %s
Note
PARAMETERS:
%s: class::method
%s: type of object
MESSAGE:
GEN_CRIT_EVTHDLCRT: %s: Error creating event Handler %s
Note
PARAMETERS:
%s: name of class::method
%s: name of event handler
MESSAGE:
GEN_CRIT_SERVICE_NOT_DEF: %s service not defined
Note
PARAMETERS:
%s: undefined service
MESSAGE:
GEN_ERR_ADD_ROUTE: %s Unable to add route (%C)
Note
PARAMETERS:
%s: name of class/method
%C): MMLname[component id]
MESSAGE:
GEN_ERR_ALLOC_EVT_FAIL: %s: Could not allocate %s %s
Note
PARAMETERS:
%s: Classmethod
%s: name of event
%s: reason for failure or supplementary string
MESSAGE:
GEN_ERR_ALM_CAT_FAIL: Alarm Cat %s not found - Cannot %s Alarm for comp %s
Note
PARAMETERS:
%s: Alarm category
%s: `set' or `clear'
%s: Component name
MESSAGE:
GEN_ERR_ALM_CAT_NOT_FOUND: alarm category %s not found in table %s
Note
PARAMETERS:
%s: name of the alarm category
%s: table name
MESSAGE:
GEN_ERR_ALM_PRXY_PROC_FAIL: Cannot create %s XEAlarmProxy for process %s
Note
PARAMETERS:
%s: alarm name
%s: process name
MESSAGE:
GEN_ERR_BUFFOV: %s buffer overflow
Note
DESCRIPTION:
This message indicates an error due to overflow of an internal buffer.
PARAMETERS:
%s: name of the buffer
MESSAGE:
GEN_ERR_CKSUM: %s CheckSum error on %s = %s
Note
PARAMETERS:
%s: Facility name
%s: Filename or connection name on which checksum error occurred
%s: String containing the checksum value or further info on the error
MESSAGE:
GEN_ERR_CORRUPT_INP: Corrupted input for %s
Note
DESCRIPTION:
Internal creation of alarm failed
PARAMETERS:
%s: Name of component with corrupted input
MESSAGE:
GEN_ERR_CPROCEXIT: %s: Child Process %d terminated with status = %d
Note
PARAMETERS:
%s: class::method name
%d: process id
%d:
MESSAGE:
GEN_ERR_DBOPEN: %s : Failed to open database %s
Note
PARAMETERS:
%s:%s class:method name
%s:%s Database name
MESSAGE:
GEN_ERR_DEPNT_GRP: %s %s cannot be a dependent group - group does not exist.
Note
PARAMETERS:
%s: classmethod
%s: name of dependent
MESSAGE:
GEN_ERR_DEPNT_PROC: %s %s cannot be a dependent process - process does not exist.
Note
PARAMETERS:
%s: classmethod
%s: name of dependent
MESSAGE:
GEN_ERR_DEP_CIRCLR: Dependency between %s and %s appears circular and will be ignored
Note
PARAMETERS:
%s: name of component
%s: name of component
MESSAGE:
GEN_ERR_DEP_GRP: %s Dependency %s cannot be placed on group - group does not exist.
Note
PARAMETERS:
%s: classmethod
%s: name of dependency
MESSAGE:
GEN_ERR_DEP_INV: Dependency between %s and %s invalid %s
Note
PARAMETERS:
%s: name of component
%s: name of component
%s: further error info or a null string
MESSAGE:
GEN_ERR_DEP_PROC: %s Dependency %s cannot be placed on process - process does not exist.
Note
PARAMETERS:
%s: classmethod
%s: name of dependency
MESSAGE:
GEN_ERR_DREG_SERVICE: Error De-Registering Service compId %C
Note
PARAMETERS:
%C: component id of service
MESSAGE:
GEN_ERR_EVTCRT: %s: Error creating event handler %s
Note
PARAMETERS:
%s: Class::method
%s: name of event handler
MESSAGE:
GEN_ERR_EVTHDLIDFIND: %s: Could not find event handler with ID = %d
Note
PARAMETERS:
%s: class::method
%d: id of event handler
MESSAGE:
GEN_ERR_EVTHDLNAMEFIND: %s: Could not find event handler %s
Note
PARAMETERS:
%s: class::method
%s: name of the event handler
MESSAGE:
GEN_ERR_EVTHNDL: %s Cannot handle event of type %d %s
Note
PARAMETERS:
%s: Classmethodeventhandler name
%d: event type
%s: further info or an empty string
MESSAGE:
GEN_ERR_EVTINIT: %s: Error initializing event handler %s
Note
PARAMETERS:
%s: class::method name
%s: event handler name
MESSAGE:
GEN_ERR_EVTINSTALL: %s: Could not install %s event handler.
Note
PARAMETERS:
%s: Class::method
%s: name of event handler
MESSAGE:
GEN_ERR_EVTNOTFND: %s Cannot find originating event %s
Note
PARAMETERS:
%s: event handler
%s: further info or an empty string
MESSAGE:
GEN_ERR_EVTREAD: %s: Error reading message, Service ID=%x, status=%d
Note
PARAMETERS:
%s: class::method
%x: name of service
%d: status
MESSAGE:
GEN_ERR_EVTWRITE: %s: Error sending message with event type %d, status = %d
Note
PARAMETERS:
%s: name of class/method name
%d: event type
%d: status
MESSAGE:
GEN_ERR_FIND: compId %C: Could not find %s
Note
PARAMETERS:
%C: Component Id
%s: Name
MESSAGE:
GEN_ERR_FOD_CXN_INV_STATE: %s Invalid state on read (%s): `%s'
Note
PARAMETERS:
%s: Facility name
%s): connection name
%s': supplementary info or a null string
MESSAGE:
GEN_ERR_FOD_SIGACT: Sigaction returned error for signal number %d, errno: %d
Note
PARAMETERS:
%d: signal number
%d: error no
MESSAGE:
GEN_ERR_FOVERD: %s
Note
DESCRIPTION:
This log message is generated by foverd to reflect the pertinent fault tolerant error information.
PARAMETERS:
%s: error string
MESSAGE:
GEN_ERR_FREADSIZE: Error reading %s with %d bytes, expected %d bytes
Note
PARAMETERS:
%s: name of file/fifo
%d: bytes read
%d: bytes expected
MESSAGE:
GEN_ERR_GETFAIL: Could not get %s id
Note
DESCRIPTION:
Only used for VSI SigChans.
PARAMETERS:
%s: name of the object
MESSAGE:
GEN_ERR_HA_UNKNCMD: FT: Unknown command %d to local node
Note
PARAMETERS:
%d: command number
MESSAGE:
GEN_ERR_HLTH_ALM_PROC_FAIL: Failed to %s health alarm for process %s %s
Note
PARAMETERS:
%s: `set' or `clear'
%s: process name
%s: further info on error or null string
MESSAGE:
GEN_ERR_IFINIT_FAIL: Could not initialize %s: %s
Note
DESCRIPTION:
This message is logged to indicate the failure to initialize an interface such as the alarm manager.
PARAMETERS:
%s: interface name
%s: format string used for logging a symbolic status code
MESSAGE:
GEN_ERR_INIT: %s Failed to initialize %s
Note
DESCRIPTION:
This is reported when initialization of a module occurs.
PARAMETERS:
%s:%s class:method name
%s:%s Module name
MESSAGE:
GEN_ERR_IPCCREATE: %s: Error creating %s IPC for %s.
Note
PARAMETERS:
%s:class::method
%s:type of IPC <READ/WRITE/READWRITE>
%s.:name of the service
MESSAGE:
GEN_ERR_IPCOPEN: %s: Error opening %s IPC for %s.
Note
PARAMETERS:
%s: class::method
%s: type of IPC <READ/WRITE/READWRITE>
%s.: name of the service
MESSAGE:
GEN_ERR_IPCPOLL: %s: Error polling IPC %s, status = %d
Note
PARAMETERS:
%s: class::method name
%s: IPC name or service name
%d:
MESSAGE:
GEN_ERR_IPCREAD: %s: Error reading IPC %s, status = %d
Note
PARAMETERS:
%s: class::method name
%s: IPC name or service name
%d:
MESSAGE:
GEN_ERR_IPCREADSIZE: Error reading IPC %s with %d bytes, %d bytes expected
Note
PARAMETERS:
%s: IPC name
%d: number of bytes read from IPC
%d: number of bytes expected
MESSAGE:
GEN_ERR_IPCWRITE: %s: Error writing IPC %s, error: = %d
Note
PARAMETERS:
%s: class::method name
%s: IPC name or service name
%d: error no
MESSAGE:
GEN_ERR_IPC_INIT: %s Error initializing %s IPC stat=%d
Note
PARAMETERS:
%s: class name
%s: IPC name
%d: errorno
MESSAGE:
GEN_ERR_LIBCFAIL: C Library call %s failure %d
Note
DESCRIPTION:
This message indicates an error was returned by a C library function.
PARAMETERS:
%s: name of the C Library function
%d: error code
MESSAGE:
GEN_ERR_MON_PROC_CRT: Attempt to create monitoring process %s failed, monitoring suspended.
Note
PARAMETERS:
%s: process name
MESSAGE:
GEN_ERR_MOOS_ALM_PROC_FAIL: Failed to %s MOOS alarm for process %s %s
Note
PARAMETERS:
%s: `set' or `clear'
%s: process name
%s: further info on error or null string
MESSAGE:
GEN_ERR_OBJCRT_FAIL: compId %C: Instantiation of %s failed in %s
Note
DESCRIPTION:
Used when object instantiation fails.
PARAMETERS:
%C: Component Id
%s: name of the object being instantiated
%s: is class::method name
MESSAGE:
GEN_ERR_PCREAT: Cannot create process %s %s.
Note
DESCRIPTION:
ProcM failed to start one of its processes.
PARAMETERS:
%s: process name
%s.: format string used for logging a symbolic status code
MESSAGE:
GEN_ERR_PEVT_WRITE: Failed to write event to process %s %s:
Note
PARAMETERS:
%s: process name
%s:: format string used for logging a symbolic status code
MESSAGE:
GEN_ERR_PEXEC: %s: Failed to run process %s, status = %d
Note
PARAMETERS:
%s: class::method
%s: name of process
%d: value of errno
MESSAGE:
GEN_ERR_PFORK: %s: Failed to fork process %s, status = %d
Note
PARAMETERS:
%s: Class::method name
%s: process name
%d: value of errno
MESSAGE:
GEN_ERR_PG_INV: Process group %s invalid %s
Note
PARAMETERS:
%s: process group name
%s: further error info or a null string
MESSAGE:
GEN_ERR_PG_RX_TIMER_NOTSUPP: Process group %s received unsupported timer event
Note
PARAMETERS:
%s: process group name
MESSAGE:
GEN_ERR_POLL: %s: %s polling error, status = %d
Note
PARAMETERS:
%s: class::method
%s: name of timer or any name to indicate the error
%d: status
MESSAGE:
GEN_ERR_PROCM_DBWRITE: %s Error writing to Database %s
Note
DESCRIPTION:
Software error reported by procM when it fails to write into a database file.
PARAMETERS:
%s:class:method name
%s:Database name
MESSAGE:
GEN_ERR_PROCM_FIND_PROC: Could not find processes to send Command : %s
Note
PARAMETERS:
%s:%s Command
MESSAGE:
GEN_ERR_PROCM_NAK: Received a NAK from %s for %s
Note
PARAMETERS:
%s:%s Process name
%s:%s command
MESSAGE:
GEN_ERR_PROC_CRASH_WITH_CORE: Process %s has crashed, Core file = %s
Note
DESCRIPTION:
Error message indicating coredump of a process and Name of the core file.
PARAMETERS:
%s: process name
%s: core file name
MESSAGE:
GEN_ERR_PROC_INV: Process %s invalid %s
Note
PARAMETERS:
%s: process name
%s: further error info or a null string
MESSAGE:
GEN_ERR_PTXN_PATH: Unable to build transition path for process %s %s.
Note
PARAMETERS:
%s: process name
%s.: further info or an empty string
MESSAGE:
GEN_ERR_REC_DBASE: %s Recovery database error %s
Note
PARAMETERS:
%s: classmethod
%s: further info on the error or a null string
MESSAGE:
GEN_ERR_REC_DBASE_COMP: %s Recovery database error %s for component %lx
Note
PARAMETERS:
%s: classmethod
%s: further info on the error or a null string
%lx: name of component
MESSAGE:
GEN_ERR_REGSERVICE: %s: Could not register service %s, status = %d
Note
PARAMETERS:
%s: class::method name
%s: service name
%d: status
MESSAGE:
GEN_ERR_REGTBL: %s Could not register Table %s
Note
PARAMETERS:
%s:%s class:method name
%s:%s table name
MESSAGE:
GEN_ERR_REGWR_SERVICE_PROC: %s Error registering write service for process %s %s.
Note
PARAMETERS:
%s: classmethod name
%s: process name
%s.: format string used for logging a symbolic status code
MESSAGE:
GEN_ERR_REM_OBJ: %s Error removing %s objects.
Note
PARAMETERS:
%s: classmethod
%s: further info or the type of the object
MESSAGE:
GEN_ERR_SERV_NOT_DEF: %s service not defined
Note
PARAMETERS:
%s: service name
MESSAGE:
GEN_ERR_TIMERINIT: %s: Failed to initialize %s timers
Note
PARAMETERS:
%s: class::method
%s: timer name
MESSAGE:
GEN_ERR_TIMERSTART: %s: Failed to start %s timer. %s
Note
PARAMETERS:
%s: class::method
%s: name of timer
%s: further information or an empty string
MESSAGE:
GEN_ERR_TMDOUT_TXN: %s Timed-out transaction %s
Note
PARAMETERS:
%s: event handler
%s: further info or an empty string
MESSAGE:
GEN_ERR_TXN_DSTR: Error destroying transaction, tid %ld %s %s.
Note
PARAMETERS:
%ld: transaction ID
%s: further info or an empty string
%s.: format string used for logging a symbolic status code
MESSAGE:
GEN_ERR_TXN_FIND: Failed to find transaction, tid %ld, for %s %s.
Note
PARAMETERS:
%ld: transaction ID
%s: facility name
%s.: format string used for logging a symbolic status code
MESSAGE:
GEN_ERR_TXN_ORG_EVT: Failed to find orig event for %s %s.
Note
PARAMETERS:
%s: facility name
%s.: format string used for logging a symbolic status code
MESSAGE:
GEN_ERR_UNKNEVT: %s: received unknown event type:subtype %d :%d
Note
PARAMETERS:
%s: class::method
%d: event type
%d: event subtype
MESSAGE:
GEN_ERR_UNKNPROT: compId %C: unknown Protocol Family, %d
Note
PARAMETERS:
%C: component id
%d: protocol family number
MESSAGE:
GEN_ERR_UNKN_ALARM: compId %C: Unknown Alarm %s
Note
PARAMETERS:
%C: component id
%s: alarm name
MESSAGE:
GEN_ERR_UNKN_COMPID: compId %C: unknown component Id %C
Note
DESCRIPTION:
This message is used to indicate an invalid component id.
PARAMETERS:
%C: component id of the component that generates the message.
%C: component id which is invalid
MESSAGE:
GEN_INFO_ADD_LINK: compId %C :Unable to add link %s
Note
PARAMETERS:
%C: component id
%s: line name / type (e.g. MTP3)
MESSAGE:
GEN_INFO_ADD_LINKSET: compId %C :Unable to add linkset %s
Note
PARAMETERS:
%C: component id
%s: name / type of linkset
MESSAGE:
GEN_INFO_CLOSE_FD: Closed %d
Note
PARAMETERS:
%d: File Descriptor for file or FIFO that was closed
MESSAGE:
GEN_WARN_EVTCRT: Error creating event handler %s
Note
PARAMETERS:
%s: name of event handler
MESSAGE:
GEN_WARN_UNKN_ALARM: Unknown Alarm %s
Note
PARAMETERS:
%s: name of unknown alarm
MESSAGE:
GEN_WARN_UNKN_TIMER_EVT: %s: received unknown timer event type/subtype %d/%d
Note
PARAMETERS:
%s: class:method name
%d: event type
%d: event subtype
MESSAGE:
GEN_WARN_UNKWNEVT: %s: received unknown event type:subtype %d : %d
Note
PARAMETERS:
%s: class::method or name of event handler
%d: event type
%d: event subtype
MESSAGE:
MGMT_CRIT_ADDFAIL: Error adding %s service
Note
PARAMETERS:
%s: name of service
MESSAGE:
MGMT_CRIT_SRVC_UNDEF: %s service is not defined
Note
DESCRIPTION:
Channel Manager service not defined in the services.dat file.
PARAMETERS:
%s: name of the service
MESSAGE:
MGMT_ERR_ADDOBJ: %s: Failed to add %s, status = %d
Note
PARAMETERS:
%s: class::method name
%s: name of the object
%d: XE status
MESSAGE:
MGMT_ERR_ARUINIT: %s: Failed to initialize ARU
Note
PARAMETERS:
%s: class::method name
MESSAGE:
MGMT_ERR_DMGR_NOTAVAIL: XEDataMgr not available
Note
MESSAGE:
MGMT_ERR_DMNOTAVAIL: %s: Data Manager is not available
Note
PARAMETERS:
%s: class::method name
MESSAGE:
MGMT_ERR_EDITALM: Failed to %s alarm: compId %C, category %d
Note
PARAMETERS:
%s: action <Add/Delete/Update>
%C: Component Id
%d: category
MESSAGE:
MGMT_ERR_EDITCLT: Failed to %s a client of service ID %d
Note
PARAMETERS:
%s: action <Add/Delete/Update>
%d: service id
MESSAGE:
MGMT_ERR_EDITTBL: %s: Failed to %s table %s
Note
PARAMETERS:
%s: class::method
%s: action <PURGE/LOAD/REGISTER/DEREGISTER/RELOAD/UPDATE>
%s: table name
MESSAGE:
MGMT_ERR_FINDALMCAT: %s: Failed to find alarm category ID %d
Note
PARAMETERS:
%s: class::method name
%d: alarm category ID
MESSAGE:
MGMT_ERR_FINDOBJ: %s: Failed to find object %s from table %s
Note
PARAMETERS:
%s: class::method name
%s: name of object
%s: name of the table
MESSAGE:
MGMT_ERR_GETALMCLTLIST: %s: Failed to get client list
Note
PARAMETERS:
%s: class::method
MESSAGE:
MGMT_ERR_GETALMREGLIST: %s Failed to get alarm registration list
Note
PARAMETERS:
%s: class::method name
MESSAGE:
MGMT_ERR_INITDMPR: %s: Failed to initialize %s, status = %d
Note
PARAMETERS:
%s: class::method
%s: name of the dumper (could be measurement report or alarm dumper)
%d: status
MESSAGE:
MGMT_ERR_INVLD_PARAM: invalid parms: fd %d, buf %s
Note
PARAMETERS:
%d: fd number
%s: contents of buffer
MESSAGE:
MGMT_ERR_MMDBDETL: ODBC Error %s, TimesTen error %d, ODBC rc %d
Note
PARAMETERS:
%s: ODBC error string
%d: x10 error code
%d: ODBC return code
MESSAGE:
MGMT_ERR_MMDBSUM: Database error while `%s' (filename %s, line %d)
Note
PARAMETERS:
%s': action being performed
%s: filename
%d: line number
MESSAGE:
MGMT_ERR_MSG_TOOLARGE: message is too large (%i)
Note
PARAMETERS:
%i: size of message
MESSAGE:
MGMT_ERR_NOTAVAIL: %s not available %s
Note
PARAMETERS:
%s:
%s:
MESSAGE:
MGMT_ERR_OPEN_SERVICE: Failed to open %s service (%i)
Note
PARAMETERS:
%s: service name
%i: service id
MESSAGE:
MGMT_ERR_POM_COMMIT: %s: commit failed, status = %d
Note
PARAMETERS:
%s: class::method
%d: status
MESSAGE:
MGMT_ERR_POM_INVALID_RST_INDEX: %s: POM received invalid result index %d
Note
PARAMETERS:
%s: class::method name
%d: index value
MESSAGE:
MGMT_ERR_POM_PEERPROV: %s: Error %s provisioning data by peer, status = %d
Note
PARAMETERS:
%s: class::method name
%s: <deploying/synchronizing>
%d: status of provisioning request
MESSAGE:
MGMT_ERR_REGALM: Failed to %s alarm registration, compId %C, alarm category %d
Note
PARAMETERS:
%s: action of Add/Delete/Update
%C: component id
%d: alarm category
MESSAGE:
MGMT_ERR_RESETALMRELAY: %s: Failed to reset alarm state (%s) relay
Note
PARAMETERS:
%s: class::method name
%s: state <INFO/MINOR/MAJOR/CRITICAL>
MESSAGE:
MGMT_ERR_SENDALM: %s: Failed to send alarm event %d to client of service ID %d
Note
PARAMETERS:
%s: class::method name
%d: type of alarm event
%d: service ID of the client
MESSAGE:
MGMT_ERR_SETALMRELAY: %s: Failed to set alarm state (%s) relay
Note
PARAMETERS:
%s: class::method
%s: state <INFO/MINOR/MAJOR/CRITICAL>
MESSAGE:
MGMT_ERR_SNMP_MKTRAPVARBIND: %s: Failed to make trap varbind for %s
Note
PARAMETERS:
%s: class::method name
%s: trap name
MESSAGE:
MGMT_ERR_SNMP_REGALM: %s: Failed to register for receiving alarm report
Note
PARAMETERS:
%s: class::method name
MESSAGE:
MGMT_ERR_SRVC_NOTAVAIL: %s service is not available in %s
Note
PARAMETERS:
%s: name of service
%s: name of module
MESSAGE:
MGMT_ERR_TBLNAME: %s: Invalid table name %s
Note
PARAMETERS:
%s: class::method
%s: name of table
MESSAGE:
MGMT_WARN_FINDALM: Failed to find alarm, compId %C, cat. Id %ld, service Id %d
Note
PARAMETERS:
%C: component Id
%ld: category Id
%d: service Id
MESSAGE:
MGMT_WARN_FINDALMREG: %s Failed to find alarm registration of service ID %d and category ID %d
Note
PARAMETERS:
%s: class::method name
%d: service id
%d: category id
MESSAGE:
MGMT_WARN_FINDOBJ: Failed to find object %s from table %s
Note
PARAMETERS:
%s: object name
%s: table name
MESSAGE:
MGMT_WARN_MMDBDLCK: Database deadlocks occurred (%d detected)
Note
PARAMETERS:
%d: number of locks
MESSAGE:
MGMT_WARN_MMDBTIMO: Database lock timeouts occurred (%d detected)
Note
PARAMETERS:
%d: number of timeouts
MESSAGE:
MGMT_WARN_READ_EVNT: read event: %x retrnd %i bytes: %i expected
Note
PARAMETERS:
%x:
%i:
%i:
MESSAGE:
MGMT_WARN_WRITE_EVT: compId %C: write failed (%s) for %s Event
Note
PARAMETERS:
%C: component id
%s: service name
%s: is the type of event
MESSAGE:
MML_ERR_BLK_STATE_UNKN: compId %C: Unknown block state=%s, CIC=%s
Note
DESCRIPTION:
This message is written when MML receives an unknown block from the engine in response to a rtrv-CIC command.
PARAMETERS:
%C: component id
%s: unknown block state
%s: CIC
MESSAGE:
PROT_CRIT_ADDFAIL: Error adding %s service
Note
PARAMETERS:
%s: name of service
MESSAGE:
PROT_CRIT_ALLOC_WRITE: Error allocating %s area
Note
PARAMETERS:
%s: is name of the area
MESSAGE:
PROT_CRIT_COMP_UNDEF: compId %C: component is not defined
Note
PARAMETERS:
%C: component id
MESSAGE:
PROT_CRIT_CREATE_THREAD_FAIL: Failed to create de-mux thread
Note
MESSAGE:
PROT_CRIT_DPNSS: critical message from DPNSS: %s
Note
PARAMETERS:
%s: text of critical message from DPNSS
MESSAGE:
PROT_CRIT_ISDN: Fatal/Critical message from ISDN: %s
Note
PARAMETERS:
%s: Text of the message
MESSAGE:
PROT_CRIT_SRVC_UNDEF: %s service is not defined
Note
DESCRIPTION:
This message indicates an error in the services.dat file.
PARAMETERS:
%s: name of the service
MESSAGE:
PROT_ERR_ADDFAIL: Error adding %s service
Note
PARAMETERS:
%s: name of the service
MESSAGE:
PROT_ERR_ADD_SESS: %C: Error adding session %s
Note
PARAMETERS:
%C: component id
%s: name of session
MESSAGE:
PROT_ERR_ALLOC_MSG: %s: Cannot allocate message area
Note
PARAMETERS:
%s: class:method name
MESSAGE:
PROT_ERR_ALLOC_PACK: Error allocating packet (%C) for channel %C
Note
DESCRIPTION:
This message is valid only for the IOCCs that use telenetwork kernel.
PARAMETERS:
%C: component id of channel where packet is being allocated
%C: component id of channel where packet is going
MESSAGE:
PROT_ERR_ALLOC_SEND: Error allocating SSC to send to %C over IP
Note
PARAMETERS:
%C: component id
MESSAGE:
PROT_ERR_ALLOC_WRITE: Error allocating %s
Note
PARAMETERS:
%s: string indicating where pdu was sent
MESSAGE:
PROT_ERR_ASN: ASN Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_ATM_ADDPOLLDEV_FAIL: compId %C: Error adding poll device %s
Note
DESCRIPTION:
Used to indicate the failure to add poll device.
PARAMETERS:
%C: componentId
%s: name of the interface
MESSAGE:
PROT_ERR_ATM_ADDVPCI_FAIL: Add VPCI failed: %s
Note
DESCRIPTION:
Used to indicate failure of VPCI addition. It is preceded by the file descriptor and VPCI value.
PARAMETERS:
%s: Error code converted to string (strerr(errno))
MESSAGE:
PROT_ERR_ATM_ADDVPCI_NOTINSERVICE: compId %C: add vpci to a stream not in-service: %s
Note
PARAMETERS:
%C: componentId
%s: function name in which this call was made
MESSAGE:
PROT_ERR_ATM_ATTACH_FAIL: ATM Attach failed: %s
Note
DESCRIPTION:
Used to indicate the failure of ATM attach. It is preceded by the file descriptor and interface number.
PARAMETERS:
%s: Error code converted to string (strerr(errno))
MESSAGE:
PROT_ERR_ATM_BWALLOC_FAIL: Bandwidth Alloc failed: %s
Note
DESCRIPTION:
Used to indicate the failure of ATM BandWidth allocation. It is preceded by the interface number.
PARAMETERS:
%s: Error code converted to string (strerr(errno))
MESSAGE:
PROT_ERR_ATM_DSL_NOTFOUND: compId %C: no DSL was found: %s
Note
PARAMETERS:
%C: componentId
%s: function name in which this call was made
MESSAGE:
PROT_ERR_ATM_FD_READ_FAIL: FD %i error reading data: %s
Note
PARAMETERS:
%i: File Descriptor
%s: Error code converted to string (strerr(errno))
MESSAGE:
PROT_ERR_ATM_INTF_OPEN_FAIL: ATM interface open failed: %s
Note
DESCRIPTION:
Used to indicate a ATM interface open failure. It is preceded by the interface name.
PARAMETERS:
%s: Error code converted to string (strerr(errno))
MESSAGE:
PROT_ERR_ATM_NO_LOCAL_DSL: compId %C: No local DSL available: %s
Note
DESCRIPTION:
Used to indicate the non availability of local DSL.
PARAMETERS:
%C: componentId
%s: function name in which this call was made
MESSAGE:
PROT_ERR_ATM_SEND_FAIL: compId %C: ioStreamSend error: %s
Note
PARAMETERS:
%C: componentId
%s: Error code converted to string (strerr(errno))
MESSAGE:
PROT_ERR_ATM_SETRAW_FAIL: ATM Set RAW failed: %s
Note
DESCRIPTION:
Used to indicate failure of ATM Set RAW. It is preceded by the interface number.
PARAMETERS:
%s: Error code converted to string (strerr(errno))
MESSAGE:
PROT_ERR_ATM_STREAM_INUSE: compId %C: stream already in use: %s
Note
PARAMETERS:
%C: componentId
%s: function name in which this call was made
MESSAGE:
PROT_ERR_ATM_UNEXPECTED_POLL: %s: Unexpected polling event
Note
PARAMETERS:
%s: function name in which this call was made
MESSAGE:
PROT_ERR_BAD_CMND: bad %s command
Note
PARAMETERS:
%s: name of the command
MESSAGE:
PROT_ERR_BSM_ADD_SESS: Failed to add session to group %i with err %x
Note
MESSAGE:
PROT_ERR_BSM_ADD_SESS_RET: Failed to add session with err %s
Note
PARAMETERS:
%s:
MESSAGE:
PROT_ERR_BSM_CRT_FAIL: Error creating Bsm object for session set %lx
Note
DESCRIPTION:
This message is no longer used.
PARAMETERS:
%lx:
MESSAGE:
PROT_ERR_BSM_CRT_MISC: Failed to %s for %lx with err %x
Note
MESSAGE:
PROT_ERR_BSM_DEL_GRP: Failed to delete group %i from set %i with err %x
Note
MESSAGE:
PROT_ERR_BSM_DEL_SESS: Failed to delete session %i from group %i with err %x
Note
MESSAGE:
PROT_ERR_BSM_DEL_SET: Failed to delete set %i with err %x
Note
MESSAGE:
PROT_ERR_BSM_GRP_CONF: Session %i already exists in group %i which conflict with group %i
Note
MESSAGE:
PROT_ERR_BSM_PLAT_INIT: bsm platform_init failed %i
Note
MESSAGE:
PROT_ERR_BSM_RUDP_CONFIG: Failed to configure rudpParms for group %i with err %x
Note
MESSAGE:
PROT_ERR_BSM_SET_EXIST: Session set %i already exists for %lx
Note
MESSAGE:
PROT_ERR_BSM_SET_REG: Failed to register %s for session set %i with err %x
Note
MESSAGE:
PROT_ERR_BSM_STBY_GRP: Failed to standby session grp %i set %i with err %x
Note
MESSAGE:
PROT_ERR_CCTC_NOT_ACTIVE: %s:CCTC not active
Note
PARAMETERS:
%s:
MESSAGE:
PROT_ERR_CCTC_NOT_STANBY: %s:CCTC not Standby
Note
PARAMETERS:
%s:
MESSAGE:
PROT_ERR_CRT_PROT_LOG: Error creating protocol logger
Note
MESSAGE:
PROT_ERR_CRT_SESS_MNGR_FAIL: Failed to create Session Manager %i
Note
MESSAGE:
PROT_ERR_DISCRD_TCP: %C: Discarding TCP DATA size =%d
Note
PARAMETERS:
%C: component id
%d: size of packet
MESSAGE:
PROT_ERR_DMGR_NOTAVAIL: XEDataMgr not available
Note
MESSAGE:
PROT_ERR_DPNSS: Error message from DPNSS: %s
Note
PARAMETERS:
%s: Text of the message
MESSAGE:
PROT_ERR_ENG_PDU_TOO_BIG: Engine PDU (%C) for channel %lx too large (%d)
Note
PARAMETERS:
%C: component id
%lx: channel
%d: size of packet
MESSAGE:
PROT_ERR_ILLEGAL_STAT: Illegal SigChan status type
Note
MESSAGE:
PROT_ERR_INIT: Cannot instantiate %s
Note
PARAMETERS:
%s: Name of module it cannot instantiate.
MESSAGE:
PROT_ERR_INVALID_MSGLEN: Invalid messageLength %d in KEEPALIVE, IPChan=%C
Note
PARAMETERS:
%d: message length
%C: component id
MESSAGE:
PROT_ERR_INVAL_STAT: Invalid State for %s Ctrl request
Note
PARAMETERS:
%s: The device name. i.e Link
MESSAGE:
PROT_ERR_INV_STAT: %C :procCtrlReq(), invalid status
Note
PARAMETERS:
%C: component id
MESSAGE:
PROT_ERR_INV_SWITCH: Switch type (%i) for %C is invalid
Note
PARAMETERS:
%i: switch type number
%C: component id
MESSAGE:
PROT_ERR_IP: IP Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_ISDN: Error message from ISDN: %s
Note
DESCRIPTION:
Refer to the Cisco Media Gateway Controller Software Release 7 Operations, Maintenance, and Troubshhooting Guide for a detailed explanation about this error message.
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_KILL_SESS_MNGR: Error terminating Session Manager %i
Note
DESCRIPTION:
Error codes:
0x51—Session does not exist.
0x01—General failure.
PARAMETERS:
%i: error code
MESSAGE:
PROT_ERR_LX_FAIL: %s for %C failed
Note
PARAMETERS:
%s: class::method
%C: component id
MESSAGE:
PROT_ERR_MAKE_REASON: FT Make %s: reason %d
Note
PARAMETERS:
%s:
%d:
MESSAGE:
PROT_ERR_MSG_SEND_FAIL: %C: %s, failed to send msg
Note
PARAMETERS:
%C: component id
%s: name of the module
MESSAGE:
PROT_ERR_MTP: MTP Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_OPC_FIND: Can not find OPC %C
Note
PARAMETERS:
%C: component id of IPC
MESSAGE:
PROT_ERR_OPEN_SERVICE: Failed to open %s service (%i)
Note
PARAMETERS:
%s: service name
%i: service id
MESSAGE:
PROT_ERR_PATH_MAP_INSERT: Failed to add path %C to path map
Note
PARAMETERS:
%C: component id of path
MESSAGE:
PROT_ERR_POOL_MEM: Cannot get memory pool
Note
MESSAGE:
PROT_ERR_PRIOCNTL_FAIL: PRIOCTL failed %s start procM as root
Note
PARAMETERS:
%s: error
MESSAGE:
PROT_ERR_PROC_IDU: %C: procEngineIDU msg buf, sigPath OOS (%d)
Note
PARAMETERS:
%C: component id of sigpath
%d: sigpath status
MESSAGE:
PROT_ERR_Q921: Q921 Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_RCV_SSC_NON_ACTV: Received SSC in non-active state %C
Note
PARAMETERS:
%C: component id
MESSAGE:
PROT_ERR_RLM: RLM Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_RUDP: RUDP Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_RUDP_INIT_FAIL: Failed to initialize RUDP, return code=%i
Note
PARAMETERS:
%i: return code
MESSAGE:
PROT_ERR_SCHEDINFO: Schedinfo lid %d rid %d
Note
PARAMETERS:
%d: lid id
%d: rid id
MESSAGE:
PROT_ERR_SCHEDINFO_FAIL: Schedinfo failed for %s
Note
PARAMETERS:
%s: is RT chmod +s Chan Ctrl
MESSAGE:
PROT_ERR_SESS_MAP_INSERT: Failed to add chan %C to session map %i
Note
PARAMETERS:
%C: component id
%i: return code
MESSAGE:
PROT_ERR_SOCKETINIT:compId %C :Socket-init failed
Note
PARAMETERS:
%C: component id
MESSAGE:
PROT_ERR_SRCP_BLD_ACTION: compId %C: Cannot specify action with SRCP signals %d
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be built because actions are not allowed with SRCP signals.
PARAMETERS:
%C: component id
%d: encoded value of the signal
MESSAGE:
PROT_ERR_SRCP_BLD_CVID: compId %C: Unrecognized control vector %d
Note
DESCRIPTION:
This message indicates an unknown parameter (encoded in binary data stream format as a control vector) in the message received from upper layer. An attempt will be made to skip over the unrecognized control vector but the message built will likely be incomplete.
PARAMETERS:
%C: component id
%d: control vector id
MESSAGE:
PROT_ERR_SRCP_BLD_CVLEN: compId %C: Incorrect length of control vector %d
Note
DESCRIPTION:
This message indicates an inconsistency in the message (encoded in binary data stream format) received from upper layer, specifically the size of a particular parameter (control vector), and building of the message is aborted.
PARAMETERS:
%C: component id
%d: control vector id
MESSAGE:
PROT_ERR_SRCP_BLD_EVT: compId %C: SRCP event %d out of range
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be built because the event specified is not in the associated package.
PARAMETERS:
%C: component id
%d: encoded value of the event
MESSAGE:
PROT_ERR_SRCP_BLD_REQEVT: compId %C: SRCP event %d cannot be requested
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be built because the requested event parameter specifies an SRCP event that cannot be requested.
PARAMETERS:
%C: component id
%d: encoded value of the event
MESSAGE:
PROT_ERR_SRCP_BLD_REQINFO: compId %C: Invalid SRCP requested info %d
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be built because the requested information parameter is invalid.
PARAMETERS:
%C: component id
%d: encoded value of the requested info
MESSAGE:
PROT_ERR_SRCP_BLD_SIGEVT: compId %C: SRCP event %d cannot be signalled
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be built because the signal request parameter specifies an SRCP event that cannot be signalled.
PARAMETERS:
%C: component id
%d: encoded value of the event
MESSAGE:
PROT_ERR_SRCP_PARSE_EPID: compId %C: Cannot parse SRCP endpoint id in %.60s
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be parsed because the endpoint ID is invalid (refer to RFC 821).
PARAMETERS:
%C: component id
%.60s: endpoint id
MESSAGE:
PROT_ERR_SRCP_PARSE_EVTPARM: compId %C: Cannot parse SRCP parameter for %s/%s
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be parsed because it contains an event which carries an invalid or extraneous parameter.
PARAMETERS:
%C: component id
%s: package
%s: event which carries the parameter
MESSAGE:
PROT_ERR_SRCP_PARSE_LINE: compId %C: Cannot parse %.60s
Note
DESCRIPTION:
This message indicates that an entire line in the SRCP message cannot be parsed.
PARAMETERS:
%C: component id
%.60s: message line
MESSAGE:
PROT_ERR_SRCP_PARSE_MSGTYPE: compId %C: Unknown or unexpected message type %.20s
Note
DESCRIPTION:
This message indicates that the SRCP message cannot be parsed because the message type is unknown or unexpected (for call agent).
PARAMETERS:
%C: component id
%.20s: message type
MESSAGE:
PROT_ERR_SRCP_RANGE_TXNID: compId %C: SRCP transaction ID %u out of range
Note
DESCRIPTION:
This message is used by components that handle SRCP messages. It indicates an error caused by an out of range transaction ID. SRCP transaction id ranges from 1 to 999999999.
PARAMETERS:
%C: component id
%u: transaction id
MESSAGE:
PROT_ERR_SRVC_NOTAVAIL: %s service is not available in %s
Note
PARAMETERS:
%s: name of service
%s: name of module
MESSAGE:
PROT_ERR_SWITCH_TYPE: compId %C :Switch type (%i) is invalid
Note
PARAMETERS:
%C: component id
%i: switch type
MESSAGE:
PROT_ERR_TCP: TCP Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_UDP: UDP Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_VSI: VSI : VSI Error Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_ERR_VSI_MASTER: compId %C: VSI Master Error log %s
Note
DESCRIPTION:
Used to display info level messages from VSI Master API.
PARAMETERS:
%C: Component Id
%s: error log from Master
MESSAGE:
PROT_ERR_VSI_RESYNC_BADCKSUMBLK_EXCEEDED: Bad Check sum blocks count %u, exceeds Maximum number of checksum blocks %u
Note
DESCRIPTION:
Used when the bad checksum block count exceeds the maximum checksum block count.
PARAMETERS:
%u: the number of bad checksum blocks
%u: the maximum number of checksum blocks.
MESSAGE:
PROT_ERR_VSI_RESYNC_CONNID_CMTSTATUSFAIL: Could not update Connection Id %u to CommitStatus %d
Note
DESCRIPTION:
Used when the commit status of the specified connection ID could not be updated.
PARAMETERS:
%u: connection ID
%d: Commit status
MESSAGE:
PROT_ERR_VSI_RESYNC_CONNID_DELETEFAIL: %s: Could not delete connId %u from %s
Note
DESCRIPTION:
Used when the specified Connection ID could not be deleted from the specified list, that is, response resyncDataarray list.
PARAMETERS:
%s: is class::method name
%u: connection Id
%s: the list (response list/resync data array)
MESSAGE:
PROT_ERR_VSI_RESYNC_CONNID_NOTFOUND: %s Connection Id %u not found in %s
Note
DESCRIPTION:
Used when connection ID could not be found in resyncdataarray/pending list/response list.
PARAMETERS:
%s: class::method name
%u: Connection Id
%s: the list (resyncDataArray or pending list or response list)
MESSAGE:
PROT_ERR_VSI_RESYNC_PENDLIST_ADDFAIL: %s: Could not add request to pending list
Note
DESCRIPTION:
Used when a request could not be added to the pending list.
PARAMETERS:
%s: is class::method name.
MESSAGE:
PROT_ERR_VSI_RESYNC_PHYSIF_NOTFOUND: Could not find Physical Id for logical I/F Id %lx
Note
DESCRIPTION:
Used when a physical interface ID corresponding to a logical interface ID could not be found.
PARAMETERS:
%lx: is the logical Interface ID.
MESSAGE:
PROT_ERR_VSI_STATUSRESP_SENDFAIL: compId %C: Failed to send status response to IOCM
Note
DESCRIPTION:
Used when the status response from VSI fails to be sent.
PARAMETERS:
%C: component id
MESSAGE:
PROT_ERR_VSI_UNKN_MSGTYPE: %s: Unknown message type %d received
Note
DESCRIPTION:
Used when an unknown message type is received by the given object in the IOCC-VSI subsystem.
PARAMETERS:
%s: class::method name
%d: message ID received
MESSAGE:
PROT_ERR_WRITE_FAIL: Write failed (%s) for %s Event (path: %08lx).
Note
MESSAGE:
PROT_ERR_WRT_BUFF: %C: procEngineIDU msg buf, error writing buffer (%d)
Note
PARAMETERS:
%C: component id
%d: size of buffer
MESSAGE:
PROT_ERR_XGCP_BLD_ACTION: compId %C: Cannot specify action with SGCP/MGCP signals %d
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be built because actions are not allowed with SGCP/MGCP signals.
PARAMETERS:
%C: component id
%d: encoded value of the signal
MESSAGE:
PROT_ERR_XGCP_BLD_CVID: compId %C: Unrecognized control vector %d
Note
DESCRIPTION:
This message indicates an unknown parameter (encoded in binary data stream format as a control vector) in the message received from upper layer. An attempt will be made to skip over the unrecognized control vector but the message built will likely be incomplete.
PARAMETERS:
%C: component id
%d: control vector id
MESSAGE:
PROT_ERR_XGCP_BLD_MODE: compId %C: Invalid SGCP/MGCP mode %d
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be built because the mode parameter is invalid.
PARAMETERS:
%C: component id
%d: encoded value of the mode
MESSAGE:
PROT_ERR_XGCP_BLD_MSGTYPE: compId %C: Invalid SGCP/MGCP message type %d
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be built because the message type specified is invalid.
PARAMETERS:
%C: component id
%d: encoded value of the message type
MESSAGE:
PROT_ERR_XGCP_BLD_OFFLIMIT: compId %C: Traversing pass end of GDS
Note
DESCRIPTION:
This message indicates an inconsistency in the message (encoded in binary data stream) received from upper layer, specifically the length of the data stream, and building of the message is aborted.
PARAMETERS:
%C: component id
MESSAGE:
PROT_ERR_XGCP_BLD_PARMTYPE: compId %C: Unknown or unsupported SGCP/MGCP parameter type %d
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be built because the event parameter type is unknown or unsupported.
PARAMETERS:
%C: component id
%d: encoded value of the event parameter type
MESSAGE:
PROT_ERR_XGCP_BLD_PKG: compId %C: SGCP/MGCP package %d out of range
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be built because the package parameter is not within the range of supported packages.
PARAMETERS:
%C: component id
%d: encoded value of the package
MESSAGE:
PROT_ERR_XGCP_BLD_REQEVT: compId %C: SGCP/MGCP event %d cannot be requested
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be built because the requested event parameter specifies a non-requestable SGCP/MGCP event.
PARAMETERS:
%C: component id
%d: encoded value of the event
MESSAGE:
PROT_ERR_XGCP_BLD_REQINFO: compId %C: Invalid SGCP/MGCP requested info %d
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be built because the requested info parameter is invalid.
PARAMETERS:
%C: component id
%d: encoded value of the requested info
MESSAGE:
PROT_ERR_XGCP_PARSE_EPID: compId %C: Cannot parse SGCP/MGCP endpoint id in %.60s
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be parsed because the endpoint ID is invalid (refer to RFC 821).
PARAMETERS:
%C: component id
%.60s: endpoint id
MESSAGE:
PROT_ERR_XGCP_PARSE_MAJVER: compId %C: SGCP/MGCP major version mismatch %d
Note
DESCRIPTION:
This message indicates the major version number in the SGCP/MGCP message does not match what this version of software supports.
PARAMETERS:
%C: component id
%d: major version number
MESSAGE:
PROT_ERR_XGCP_PARSE_MSGTYPE: compId %C: Unknown or unexpected message type %.20s
Note
DESCRIPTION:
This message indicates that the SGCP/MGCP message cannot be parsed because the message type is unknown or unexpected (for call agent).
PARAMETERS:
%C: component id
%.20s: message type
MESSAGE:
PROT_ERR_XGCP_RANGE_TXNID: compId %C: SGCP/MGCP transaction ID %u out of range
Note
DESCRIPTION:
This message is used by components that handle SGCP/MGCP messages. It indicates an error due to an out of range transaction ID. SGCP/MGCP transaction IDs range from 1 to 999999999.
PARAMETERS:
%C: component id
%u: transaction id
MESSAGE:
PROT_WARN_ASN: ASN Warning Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_WARN_CHAN_NOT_CREATED: channel not created %C
Note
PARAMETERS:
%C: component id
MESSAGE:
PROT_WARN_CONFLIC_CONFIG: compId %C: Conflicting IP configurations w/ channels %C
Note
PARAMETERS:
%C: component Id of channel
%C: component id of channel whose config is conflicting with the other channel
MESSAGE:
PROT_WARN_DPNSS: DPNSS Warning Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_WARN_IP: Warning message from IP: %s
Note
PARAMETERS:
%s: Text of the message
MESSAGE:
PROT_WARN_ISDN: Warning message from ISDN: %s
Note
PARAMETERS:
%s:
MESSAGE:
PROT_WARN_MTP3: MTP3 Warning Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_WARN_NOPOLLIN: Received a message from a file descriptor that is not being polled.
Note
MESSAGE:
PROT_WARN_POLLERR: POLLERR file descriptor %d
Note
DESCRIPTION:
IOCC encountered an error while polling a file descriptor. As a result, the IOCC has stopped polling that file descriptor.
PARAMETERS:
%d: file descriptor number
MESSAGE:
PROT_WARN_Q921: Q921 Warning Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_WARN_READFAIL: read failed (%s) %s event (%x)
Note
MESSAGE:
PROT_WARN_READ_EVNT: read event: %x retrnd %i bytes: %i expected
Note
MESSAGE:
PROT_WARN_RLM: compId %C: RLM should not be here
Note
PARAMETERS:
%C: component id
MESSAGE:
PROT_WARN_RUDP: RUDP Warning Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_WARN_SRCP_PARSE_LONGCOMM: compId %C: Long SRCP comment truncated %.60s
Note
DESCRIPTION:
This message indicates that the SRCP message contains a long comment and only a truncated copy will be passed to upper layer.
PARAMETERS:
%C: component id
%.60s: comment
MESSAGE:
PROT_WARN_UDP: UDP Warning Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_WARN_VSI: VSI Warning Message %s
Note
PARAMETERS:
%s: general error string
MESSAGE:
PROT_WARN_WRITE_EVT: compId %C: write failed (%s) for %s Event
Note
PARAMETERS:
%C: component id
%s: service name
%s: is the type of event
MESSAGE:
TIOS_CRIT_MSG_WRT_FAIL: msg write failed = %d
Note
PARAMETERS:
%d: error code
MESSAGE:
TIOS_CRIT_STPSCP_INDEX: STPSCP index = %d is assigned to SSN = %d and SSN = %d in STP.DAT
Note
PARAMETERS:
%d: STPSCP index value from STP.dat
%d: %d SSN values in STP.dat associated with the STPSCP index
MESSAGE:
TIOS_CRIT_TCAPSTACK: TCAP stack interface error. %s failed. SSN =%d
Note
PARAMETERS:
%s: Name of the stack function that returned an Error
%d: Subsystem number
MESSAGE:
TIOS_ERR_ADD: Failure adding %C
Note
PARAMETERS:
%C: component id of object attempted to be added
MESSAGE:
TIOS_ERR_ADDOBJ: %C: Adding %s
Note
PARAMETERS:
%C: is compID
%s: is the name of the object added.
MESSAGE:
TIOS_ERR_ASP_MSG: compId %C: Sending SSC with an unknown transition because signal=%08x
Note
PARAMETERS:
%C: component id
%08x: component id of signal
MESSAGE:
TIOS_ERR_BAD_SIDE: %s bad %s side for sigpath %x
Note
MESSAGE:
TIOS_ERR_BUF_TOO_SMALL: %s - buffer size exceeded
Note
MESSAGE:
TIOS_ERR_CARD_INIT: %s Card Instantiation
Note
PARAMETERS:
%s: name of the card
MESSAGE:
TIOS_ERR_COLL_ERR: ITK IO Card Statistics Gather Failure on card %d
Note
PARAMETERS:
%d: card number
MESSAGE:
TIOS_ERR_CREATELINE: Line create error compId %C
Note
PARAMETERS:
%C: component id of the line
MESSAGE:
TIOS_ERR_CRT_FAIL: %C: Cannot create ioCC
Note
PARAMETERS:
%C: component id of channel controller
MESSAGE:
TIOS_ERR_DATA_TABLE: Failed to load data table %s
Note
PARAMETERS:
%s: Data table name
MESSAGE:
TIOS_ERR_EVT_FAIL: Failed to write %s event on SVC %s
Note
PARAMETERS:
%s: event type (ex: control)
%s: name of the svc
MESSAGE:
TIOS_ERR_FIND: %s %s component type not found
Note
MESSAGE:
TIOS_ERR_FORMT_INV: physLineIf: %08lx - format %s is invalid for CEPT carrier
Note
MESSAGE:
TIOS_ERR_INTRNL_ERR: INTERNAL: %s errors
Note
MESSAGE:
TIOS_ERR_IPC_ERR: Received IPC Error from %s compId %C
Note
PARAMETERS:
%s: indicates where error is coming from (for example, . line card)
%C: component id of that component
MESSAGE:
TIOS_ERR_MAP_FAM_FAIL: %lx: FAILURE pc cannot map family %d
Note
PARAMETERS:
%lx:component id of the pointcode
%d:Point code family type that can not be mapped.
MESSAGE:
TIOS_ERR_MEAS_ADD: Failed to add a measurement for %x, unknown measurement %s
Note
PARAMETERS:
%x: Component Id
%s: Measurement name
MESSAGE:
TIOS_ERR_MLTPL_PROT_ENTRS: (%C) Multiple control protocol entries found to same GW in .dat files
Note
PARAMETERS:
%C: component id of sigPath
MESSAGE:
TIOS_ERR_NO_TYPE_PC: %C: Point code with no type
Note
DESCRIPTION:
Pointcode type of the parameter is unknown. Examples of pointcode types are ANSI, ETSI, NTT, and CHINA.
PARAMETERS:
%C: component id of point code
MESSAGE:
TIOS_ERR_NULL_PTR: %s - NULL GDS message pointer
Note
PARAMETERS:
%s: class::method name
MESSAGE:
TIOS_ERR_OPEN: channel compId %C: Failure opening Svc %s %s
Note
PARAMETERS:
%C: component id
%s: buffer
%s: name of the svc
MESSAGE:
TIOS_ERR_RUDP_ADD_DEL: %p, rudpAddDeleteFd failed
Note
PARAMETERS:
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_ADD_FD: rudpAddDeleteFd, exceeded number of fds adding fd %d
Note
PARAMETERS:
%d: file descriptor
MESSAGE:
TIOS_ERR_RUDP_ALLOC_CONN: rudp_accept, connection failed to open
Note
MESSAGE:
TIOS_ERR_RUDP_ALLOC_CREC: rudp_accept, failed to create new connection record
Note
MESSAGE:
TIOS_ERR_RUDP_ARR_INVAL_STATE: rudpSegArrival, connection %p invalid state %d
Note
PARAMETERS:
%p: pointer to connection record
%d: current state
MESSAGE:
TIOS_ERR_RUDP_BUF_EMPTY: Send buffer empty in rudp_send()
Note
MESSAGE:
TIOS_ERR_RUDP_BUF_FREE: rudpBufFree, failed buffer %p
Note
PARAMETERS:
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_BUF_FREE_TWICE: rudpBufFree, buffer freed twice
Note
MESSAGE:
TIOS_ERR_RUDP_BUF_GETSZ: rudpBufGetSz, failed buffer %p
Note
PARAMETERS:
%p: pointer to buffer
MESSAGE:
TIOS_ERR_RUDP_BUF_SETSZ: rudpBufSetSz, failed buffer %p
Note
PARAMETERS:
%p: pointer to buffer
MESSAGE:
TIOS_ERR_RUDP_BUF_TOO_LARGE: Buffer too large in rudp_send().Received %d, max_allowed %d
Note
PARAMETERS:
%d: number of bytes received
%d: maximum buffer size
MESSAGE:
TIOS_ERR_RUDP_CLOSE: Cannot close server connection record, there are active clients
Note
MESSAGE:
TIOS_ERR_RUDP_CLOSE_DATA: rudp_close, rudpWaitData failed
Note
MESSAGE:
TIOS_ERR_RUDP_CLOSE_WAIT: Error - connection already being closed
Note
MESSAGE:
TIOS_ERR_RUDP_CREC: Trying to remove connection %p, from %p, which has no children
Note
PARAMETERS:
%p: pointer to connection record
%p: pointer to connection record (parent)
MESSAGE:
TIOS_ERR_RUDP_CREC2: Trying to remove connection %p, from %p, which is not a parent
Note
PARAMETERS:
%p: pointer to connection record
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_CREC3: Trying to remove connection %p, from %p, list empty
Note
PARAMETERS:
%p: pointer to connection record
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_CREC4: Trying to remove connection %p, from %p, not in list
Note
PARAMETERS:
%p: pointer to connection record
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_DEL_FD: rudpAddDeleteFd, failed to delete fd %d
Note
PARAMETERS:
%d: file descriptor
MESSAGE:
TIOS_ERR_RUDP_INVAL_CONNID: Invalid Connection ID
Note
MESSAGE:
TIOS_ERR_RUDP_INVAL_CONNTYPE: rudpAddDeleteFd, invalid connection type (%d) adding fd %d
Note
PARAMETERS:
%d: connection type
%d: file descriptor
MESSAGE:
TIOS_ERR_RUDP_INVAL_STATE: Error - invalid state
Note
MESSAGE:
TIOS_ERR_RUDP_IN_SEQ: rudpProcessInSeq, connection %p failed to get buffer from out-of-sequence queue
Note
PARAMETERS:
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_LISTEN_CREC: rudp_listen, cannot find connection record, error %d
Note
PARAMETERS:
%d: error code
MESSAGE:
TIOS_ERR_RUDP_LISTEN_INVAL_CREC: rudp_listen, invalid connection record, %p
Note
PARAMETERS:
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_MAX_FD: Exceeded max number of file descriptors (RUDP)
Note
MESSAGE:
TIOS_ERR_RUDP_MAX_RESYN: Connection %p, maximum number (%d) of soft resets exceeded
Note
PARAMETERS:
%p: pointer to connection record
%d: number of soft resets
MESSAGE:
TIOS_ERR_RUDP_MAX_RETRANS: Connection %p, maximum number (%d) of retransmission exceeded
Note
PARAMETERS:
%p: pointer to connection record
%d: maximum number of retranmissions
MESSAGE:
TIOS_ERR_RUDP_NEXT_CREC: rudp_next, cannot find connection record, fd %d
Note
PARAMETERS:
%d: file descriptor
MESSAGE:
TIOS_ERR_RUDP_NO_MORE_CREC: rudpConnAdd, no more connection records
Note
MESSAGE:
TIOS_ERR_RUDP_OOS_QUEUE_EMPTY: rudpRemoveSentSegment, conn %p out-of-sequence empty
Note
PARAMETERS:
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_QUEUE_EMPTY: rudpFront, connection %p input queue is empty
Note
PARAMETERS:
%p: pointer to connection record
MESSAGE:
TIOS_ERR_RUDP_RETRANS: rudpRetransmit, failed to retrieve size of header
Note
MESSAGE:
TIOS_ERR_RUDP_SEM_WAIT: rudpFront, connection %p sem_wait failed, rc = %d
Note
PARAMETERS:
%p: pointer to connection record
%d: return code
MESSAGE:
TIOS_ERR_RUDP_TIMER: rudp_timer, NULL rudpFirstConn
Note
MESSAGE:
TIOS_ERR_RUDP_WAIT_DATA: rudpWaitDat, connection %p sem_wait failed, rc %d
Note
PARAMETERS:
%p: pointer to connection record
%d: return code
MESSAGE:
TIOS_ERR_SCCP_CONFIG_FAIL: SCCP Config failed. Element=%d,Instance=%d,reason=%d
Note
PARAMETERS:
%d: Type of configuration that failed.
%d: Instance number
%d: reason.
MESSAGE:
TIOS_ERR_SCCP_INVALID_EVT:Invalid event in SCCP prim %d spId %d cause %d
Note
PARAMETERS:
%d: Event Id.
%d: SCCP service provider ID
%d: Cause.
MESSAGE:
TIOS_ERR_SCCP_INVALID_MTP3_EVT:Invalid event in SCCP from MTP3 prim %d spId %d cause %d
Note
PARAMETERS:
%d: Event Id.
%d: SCCP service provider ID
%d: Cause.
MESSAGE:
TIOS_ERR_SCCP_INVALID_TCAP_EVT:Invalid event in SCCP from TCAP prim %d spId %d cause %d
Note
PARAMETERS:
%d: Event Id.
%d: SCCP service provider ID
%d: Cause.
MESSAGE:
TIOS_ERR_SCCP_ROUTING_ERR: SCCP ROUTING ERROR. UNKNOWN ROUTE.
Note
MESSAGE:
TIOS_ERR_SCCP_SYNTAX_ERR: Syntax error in SCCP switch %d suId = %d
Note
PARAMETERS:
%d: Protocol variant.
%d: SCCP service user ID
MESSAGE:
TIOS_ERR_SC_SSC_UNKWN: compId %C: Unknown %s SSC transition %d
Note
DESCRIPTION:
This message indicates that the channel manager could not handle the SSC message from the channel controller.
PARAMETERS:
%C: component id
%s: name of the SSC
%d: state transition
MESSAGE:
TIOS_ERR_SIGPATH: sigpath create error compId %C
Note
PARAMETERS:
%C: component id of SigPath
MESSAGE:
TIOS_ERR_SIZE_NOT_MATCH: %s - buffer size not match GDS length
Note
PARAMETERS:
%s:Name of the method logging this error message.
MESSAGE:
TIOS_ERR_SSCTRANS: %s SSC transition Cause %s default %d
Note
PARAMETERS:
%s: location SSC origin
%s: the cause
%d: default value
MESSAGE:
TIOS_ERR_STACK_SWERR: Software error: FILE=%s, LINE=%d, ERRVAL = %d
Note
PARAMETERS:
%s: File name in which the error was detected
%d: Line number
%d: Error Value
MESSAGE:
TIOS_ERR_STREAM: %s stream error
Note
PARAMETERS:
%s: name of the class
MESSAGE:
TIOS_ERR_TCAPCONFIG: TCAP %s config not OK, Param = %d
Note
DESCRIPTION:
This error indicates an internal configuration error in TCAP process.
PARAMETERS:
%s: Configuration type.
%d: Parameter associated with the error.
MESSAGE:
TIOS_ERR_TCAP_ENGINE: TCAP-ENGINE interface error. Bad or missing %s. msgType=%d. param=%d
Note
PARAMETERS:
%s: Name of the parameter associated with the error
%d: Message type
%d: Parameter value
MESSAGE:
TIOS_ERR_TCAP_GEN_FAIL: %s failed in %s. Param =%d
Note
PARAMETERS:
%s: Name of the method
%s: class::method
%d: Parameter
MESSAGE:
TIOS_ERR_UNKNOUTPUT: compId %C: Unknown output %x
Note
PARAMETERS:
%C: component id
%x:
MESSAGE:
TIOS_ERR_UNKN_TRANS: Unknown %s Transition %d
Note
PARAMETERS:
%s: i.e CheckPt or UI
%d: Transition id
MESSAGE:
TIOS_ERR_UNKN_TYPE: %s - Unknown %s message type %d
Note
MESSAGE:
TIOS_ERR_UNKN_VCTR_TYPE: %s - Unknown Control Vector type %d
Note
MESSAGE:
TIOS_ERR_VALIDATING_OP: Validating %s for op=%d
Note
DESCRIPTION:
This should be changed to an INFO message since this is not an error.
PARAMETERS:
%s:s is table name.
%d:d is op
MESSAGE:
TIOS_INFO_ADDOBJ: %C: Added
Note
PARAMETERS:
%C: is component ID
MESSAGE:
TIOS_INFO_FIND_IOCC_FAIL_CRT: %C: Cannot find ioCC: %C - Creating
Note
PARAMETERS:
%C: component id of channel controller not found
%C: component id of new channel controller being created
MESSAGE:
TIOS_WARN_ADDOBJ: Adding Object %s compId %C:
Note
PARAMETERS:
%s: name of the object
%C: component id of object
MESSAGE:
TIOS_WARN_ADD_DEVICE: Adding %C on device %s
Note
PARAMETERS:
%C: component id of object
%s: name of the object
MESSAGE:
TIOS_WARN_ADD_SIGPATH: Adding Lisup SigPath %C
Note
PARAMETERS:
%C: component id of sigpath
MESSAGE:
TIOS_WARN_ASP_RESET: %C: Receive Reset from ASP CC
Note
DESCRIPTION:
Since ASP IOCC is no longer used, this message should never appear in the log file.
PARAMETERS:
%C: component id of ASP channel controller
MESSAGE:
TIOS_WARN_ASP_SSC_RCV: %X : Received ASP SSC=%d CAUSE=%d
Note
DESCRIPTION:
Since ASP IOCC is no longer used, this message should never appear in the log file.
PARAMETERS:
%X:
%d:
%d:
MESSAGE:
TIOS_WARN_ATTACH_ROUTE: %C: Attaching Route to linkset=%C
Note
PARAMETERS:
%C: component id of route
%C: component id of linkset
MESSAGE:
TIOS_WARN_BAD_SIDE: %s bad %s side for sigpath %x
Note
MESSAGE:
TIOS_WARN_DELOBJ: Deleting object %x
Note
PARAMETERS:
%x: Component Id
MESSAGE:
TIOS_WARN_DLD: IOCC %C is not downloaded.
Note
PARAMETERS:
%C: component id of channel controller being downloaded
MESSAGE:
TIOS_WARN_DONE_ADD_SIGPATH: Done adding Lisup SigPath %C
Note
PARAMETERS:
%C: component id of SigPath
MESSAGE:
TIOS_WARN_EVT_FAIL: Failed Unknown %s Event subtype=%d
Note
PARAMETERS:
%s: Event name
%d: subtype number
MESSAGE:
TIOS_WARN_EVT_NOT_IMPL: %x: FAILURE Event %d not implemented
Note
PARAMETERS:
%d: Event number
MESSAGE:
TIOS_WARN_EVT_RCV: Received an unknown %s. Event subtype=%d
Note
PARAMETERS:
%s.: Event name
%d: subtype number
MESSAGE:
TIOS_WARN_FIND: %C cannot find component name
Note
PARAMETERS:
%C: component id
MESSAGE:
TIOS_WARN_GEN_UNSIGNAL: %C: Generated unknown signal %x
Note
DESCRIPTION:
The state machine for the component cannot handle the output signal.
PARAMETERS:
%C: component id
%x: sigid
MESSAGE:
TIOS_WARN_MAXCONFIG: Configured limit for %s has reached. Limit=%d
Note
PARAMETERS:
%s: Name of the configured parameter
%d: Maximum configured value
MESSAGE:
TIOS_WARN_MGMT_EVT_NOT_IMPL: %C: FAILURE mgmt event subtype=%d not implemented
Note
PARAMETERS:
%C: component id
%d: subevent type
MESSAGE:
TIOS_WARN_PC_SSC_RCV: %X: Received SC-SSC TRANSITION = %d CAUSE=%d
Note
PARAMETERS:
%X:component id for which SSC is received.
%d:new state.
%d:cause for the transition.
MESSAGE:
TIOS_WARN_PC_SSC_XMIT: %X: Transmitted SC-SSC TRANSITION = %d CAUSE=%d
Note
PARAMETERS:
%X:Component for which the SSC is transmitted.
%d:Requested transition.
%d:Cause
MESSAGE:
TIOS_WARN_RELOAD: Dynamic reconfig: Entering update handler for %s
Note
DESCRIPTION:
The update handler for the data file is invoked during dynamic reconfiguration.
PARAMETERS:
%s: name of data file
MESSAGE:
TIOS_WARN_SP_SSC_XMIT: %X: Transmit SP-SSC TRANSITION= %d, CAUSE =%d
Note
PARAMETERS:
%X:component id
%d:Requested state transition.
%d:cause
MESSAGE:
TIOS_WARN_SSC_TRANS: compId %C: XMIT SSC transition %d
Note
PARAMETERS:
%C: Component Id
%d: Transition ID
MESSAGE:
TIOS_WARN_TCAP_GEN_DEL: Deleting %s. Param = %d
Note
PARAMETERS:
%s.: Object name being deleted.
%d: Parameter.
MESSAGE:
TIOS_WARN_TIMER_EVT_NOBUF: Received timer event with no buffer
Note
MESSAGE:
TIOS_WARN_UNKN_LCD_TP: line coding type %s is not recognized
Note
DESCRIPTION:
This message is no longer used by TIOS subsystem.
PARAMETERS:
%s:
MESSAGE:
TIOS_WARN_UNREC: %s not recognized
Note
DESCRIPTION:
This message is no longer used by TIOS subsystem.
PARAMETERS:
%s:
MESSAGE:
TIOS_WARN_UNREC_ENUM: %s enum %d is not recognized
Note
DESCRIPTION:
Card type parameter in one of the records in the physLineIf.dat file is not recognized.
PARAMETERS:
%s:
%d:
MESSAGE:
TIOS_WARN_UNREC_INVRTR: Inverted HDLC type %s is not recognized
Note
DESCRIPTION:
Configuration error in physLineIf.dat.
PARAMETERS:
%s:
MESSAGE:
TIOS_WARN_UNREC_LINE: line %s type %s is not recognized
Note
DESCRIPTION:
Configuration error in the physLineIf.dat file.
PARAMETERS:
%s:parameter
%s:value that is not recognized
MESSAGE:
TIOS_WARN_UNSIGNAL: %x: unknown signal %s
Note
PARAMETERS:
%x:component id
%s:signal
MESSAGE:
TIOS_WARN_UNXP_TYPE: unexpected %s type %i
Note
DESCRIPTION:
Configuration error in physLineIf.dat.
PARAMETERS:
%s: name of the event
%i: type of the event
MESSAGE:
TIOS_WARN_UPDOBJ: Failed to update %s, compId %C
Note
PARAMETERS:
%s: name of the object
%C: component id of object
MESSAGE:
TIOS_WARN_UPD_DEST: Update Destination %C
Note
DESCRIPTION:
Updating the destination during dynamic reconfiguration.
PARAMETERS:
%C: component id of destination
MESSAGE:
TIOS_ERR_INV_IDU: %s IDU message Error: %s
Note
PARAMETERS:
%s: class::method
%s: error reason
MESSAGE:
MGMT_INFO_MMDBALRT: MMDB ALERT: %s
Note
PARAMETERS:
%s: alert string
MESSAGE:
TIOS_WARN_OBJNOTFND_MIB: compId %C: Entry not found in the MIB.
Note
PARAMETERS:
%C: Component id of the object that was not found in the MIB.
Feedback