N Show Commands

show nbm defaults

show nbm defaults

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

defaults

Default config

Command Mode

  • /exec

show nbm flow-policy

show nbm flow-policy [ name { <policy-name> } ]

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

flow-policy

Flow policy show command

name

(Optional) Policy name

policy-name

(Optional) Policy name value

Command Mode

  • /exec

show nbm flows

show nbm flows [ group-based | m-group <group-ip-id> | { flow-policy { <cfg-pol-name> | <unknown-pol-name> } } | source <source-ip> [ group <group-ip> ] | group <group-ip> [ source <source-ip> ] | interface <if-name> ] [ all | active | inactive | no-receiver ] [ detail ] [ __readonly__ TABLE_flows { <mcast_grp> <src_ip> <start_time> <src_intf> <src_nbr_device> <lid> <status> <num_rx> <bw_mbps> <cfg_mbps> <src_slot> <unit> <slice> } [ { <act_slot> <act_unit> <stdby_slot> <stdby_unit> } ] { <dscp> <qos> <owner_type> <pol_name> } [ <flag> ] [ { <n_link> <num_links> } ] [ { <slot_2> <unit_2> <num_rx_2> } ] [ { <iiod> <ilink> <i_ifidx> <fab_iiod> <fab_oiod> <fab_ifidx> <oiod> <olink> <i_ieth_port> <fab_ieth_port> } ] [ { <rcv_if_idx> <iod> <name> <rcv_nbr_device> } ] [ { <end_timestr> <flow_rate_bps> <packets> <bytes> } ] ]

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

flows

NBM flows (default will be active flows)

active

(Optional) Active flows (default)

inactive

(Optional) Inactive flows

no-receiver

(Optional) Flows without any receiver

all

(Optional) Both active and inactive flows

group-based

(Optional) Multicast group based (*,G) flows to IGMP receivers

m-group

(Optional) Multicast group

group-ip-id

(Optional) Multicast group address

flow-policy

(Optional) Flow policy

cfg-pol-name

(Optional) Policy name

unknown-pol-name

(Optional) Policy name

source

(Optional) Source IP address

source-ip

(Optional) Source IP address

group

(Optional) Multicast group

group-ip

(Optional) Multicast group address

interface

(Optional) Ingress interface

detail

(Optional) Detailed output

if-name

(Optional) Interface name

__readonly__

(Optional)

TABLE_flows

(Optional) Flow stats table

mcast_grp

(Optional) Multicast group IP

src_ip

(Optional) Source IP

start_time

(Optional) Start time

src_intf

(Optional) Ingress source interface

src_nbr_device

(Optional) Ingress neighbor device name

lid

(Optional) Logical internal flow ID

status

(Optional) Flow status

num_rx

(Optional) Number of receivers

bw_mbps

(Optional) Set bandwidth

cfg_mbps

(Optional) Configured bandwidth

src_slot

(Optional) Source slot

unit

(Optional) Source unit

slice

(Optional) Source slice

dscp

(Optional) Flow DSCP

qos

(Optional) Flow QOS group

owner_type

(Optional) Flow Owner type

pol_name

(Optional) Flow Policy name

flag

(Optional) Flow not guarantee flag

n_link

(Optional) N Link

num_links

(Optional) Number of Links

act_slot

(Optional) Active FM Slot

act_unit

(Optional) Active FM Unit

stdby_slot

(Optional) Standby FM Slot

stdby_unit

(Optional) Standby FM Unit

slot_2

(Optional) Slot

unit_2

(Optional) Unit

num_rx_2

(Optional) Number of Receivers

iiod

(Optional) IIOD

ilink

(Optional) Ilink

i_ifidx

(Optional) Internal IF IDX

fab_iiod

(Optional) Fabric IIOD

fab_oiod

(Optional) Fabric OIOD

fab_ifidx

(Optional) Fabric IFIDX

oiod

(Optional) OIOD

olink

(Optional) OLink

i_ieth_port

(Optional) Internal IEth Link

fab_ieth_port

(Optional) Fabric IEth Port

rcv_if_idx

(Optional) Receiver interface index

iod

(Optional) Outgoing IOD

name

(Optional) Outgoing interface name

rcv_nbr_device

(Optional) Outgoing neighbor device name

end_timestr

(Optional) Deleted flow end time

flow_rate_bps

(Optional) Deleted flow flow rate in bps

packets

(Optional) Deleted flow packets

bytes

(Optional) Deleted flow bytes

Command Mode

  • /exec

show nbm flows bandwidth

show nbm flows bandwidth

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

flows

NBM flows

bandwidth

Per Flow Bandwidth in Mbps

Command Mode

  • /exec

show nbm flows statistics

show nbm flows statistics [ group-based | m-group <group-ip-id> | { flow-policy { <cfg-pol-name> | <unknown-pol-name> } } ] [ interface <if-name> ] [ __readonly__ { TABLE_stats <mcast_grp> <src_ip> <start_time> <src_intf> <packets> <bytes> <allow_bytes> <drop_bytes> } ]

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

flows

NBM flows

statistics

Flow statistics

group-based

(Optional) Multicast group based (*,G) flows to IGMP receivers

m-group

(Optional) Multicast group

group-ip-id

(Optional) Multicast group address

flow-policy

(Optional) Flow policy

cfg-pol-name

(Optional) Policy name

unknown-pol-name

(Optional) Policy name

interface

(Optional) Ingress port

if-name

(Optional) Interface name

__readonly__

(Optional)

TABLE_stats

(Optional) Flow stats table

mcast_grp

(Optional) Multicast group IP

src_ip

(Optional) Source IP

start_time

(Optional) Start time

src_intf

(Optional) Ingress source interface

packets

(Optional) Packets

bytes

(Optional) Bytes

allow_bytes

(Optional) Allowed bytes

drop_bytes

(Optional) Droped bytes

Command Mode

  • /exec

show nbm flows summary

show nbm flows summary [ __readonly__ TABLE_flows_summary { <flow_type> <sg> <starg> <total> } ]

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

flows

NBM Flows

summary

NBM Flow Summary

__readonly__

(Optional)

TABLE_flows_summary

(Optional) Flows summary

flow_type

(Optional) Type of Flow Summary

sg

(Optional) (S,G) number of flows

starg

(Optional) (*,G) number of flows

total

(Optional) Total Flows

Command Mode

  • /exec

show nbm host-policy all

show nbm host-policy all { sender | { receiver { local | external } } }

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

host-policy

Host policy

all

All policies on switch

sender

Sender Policy

receiver

Receiver Policy

local

Local receiver policy

external

External receiver policy

Command Mode

  • /exec

show nbm host-policy applied

show nbm host-policy applied { sender { all | interface { <if-name> } } }

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

host-policy

Host policy

applied

Applied policies only

sender

Sender Policy

all

All policies on switch

interface

Interface

if-name

Interface name

Command Mode

  • /exec

show nbm host-policy applied receiver

show nbm host-policy applied receiver { local { all | interface { <if-name> } } | external }

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

host-policy

Host policy

applied

Applied policies only

receiver

Receiver Policy

local

Local receiver policy

all

All policies on switch

external

External receiver policy

interface

Interface

if-name

Interface name

Command Mode

  • /exec

show nbm interface bandwidth

show nbm interface bandwidth [ __readonly__ [ TABLE_bw { <index> <ifname> <iod> <slot> <unit> <slice> <ingr_fl_bw_available> <ingr_fl_bw_usable> <ingr_fl_bw_capacity> <egr_fl_bw_available> <egr_fl_bw_capacity> <nbr_dev_id> <nbr_dev_name> <external> } ] ]

Syntax Description

show

Show running system information

nbm

Non Blocking Multicast

interface

interface

bandwidth

Bandwidth interface table

__readonly__

(Optional)

TABLE_bw

(Optional) TABLE BW

index

(Optional) Index

ifname

(Optional) Interface

iod

(Optional) IOD

slot

(Optional) SLOT

unit

(Optional) UNIT

slice

(Optional) SLICE

ingr_fl_bw_available

(Optional) Ingress Flow BW available

ingr_fl_bw_usable

(Optional) Ingress Flow BW usable

ingr_fl_bw_capacity

(Optional) Ingress Flow BW capacity

egr_fl_bw_available

(Optional) Egress Flow BW available

egr_fl_bw_capacity

(Optional) Egress Flow BW capacity

nbr_dev_id

(Optional) Neighbor device ID

nbr_dev_name

(Optional) Neighbor device name

external

(Optional) External

Command Mode

  • /exec

show ngoam interface statistics

show ngoam interface statistics [ __readonly__ [ TABLE_stats { <interface-name> <tx> <rx> } <statistics-end> ] ]

Syntax Description

TABLE_stats

(Optional) interface statistics table

interface-name

(Optional) interface namestring

tx

(Optional) ngoam probe transmit on the interface

rx

(Optional) ngoam probe receive on the interface

show

Show running system information

ngoam

ngoam

interface

probe packet interface

statistics

ngoam probe interface statistics

__readonly__

(Optional) Read Only

statistics-end

(Optional) statistics table end marker

Command Mode

  • /exec

show ngoam loopback

show ngoam loopback { { statistics { session { <handle> | all } | summary } } | { status { session { <handle> | all } } } } [ __readonly__ [ TABLE_statistics { <sender-handle> <connect-check-id> <last-clear-stats> TABLE_stats_attr { <stat-attr> <stat-value> } } ] [ TABLE_status { <st-sender-handle> <type> <state> } ] [ TABLE_statistics_summary { <last-clear-summary-stats> <tx> <rx> <timeout> <unsent> <req-sw-fwd> <req-drop> <resp-tx> <resp-rx> <resp-unsent> <resp-dup> <resp-sw-fwd> <resp-drop> } ] ]

Syntax Description

show

Show running system information

ngoam

ngoam

loopback

ngoam loopback

statistics

ngoam loopback statistics

summary

ngoam loopback statistics summary

status

ngoam loopback status

session

ngoam loopback session

session

ngoam loopback session

handle

ngoam loopback session handle

handle

ngoam loopback session handle

all

Display results for all ping/loopback sessions

all

Display results for all ping/loopback sessions

TABLE_statistics

(Optional) statistics table

sender-handle

(Optional) sender handle

connect-check-id

(Optional) connect check id

last-clear-stats

(Optional) last clear time for statistics

TABLE_stats_attr

(Optional) Stats attributes table

stat-attr

(Optional) stats type

stat-value

(Optional) stats value

TABLE_statistics_summary

(Optional) statistics summary table

last-clear-summary-stats

(Optional) last clear time for summary statistics

tx

(Optional) summary request sent

rx

(Optional) summary reply received

timeout

(Optional) summary timeout

unsent

(Optional) summary unsent

resp-tx

(Optional) summary resp tx

resp-rx

(Optional) summary resp rx

resp-unsent

(Optional) summary resp unsent

resp-dup

(Optional) Duplicate responses received

req-sw-fwd

(Optional) Request pkts sw fwded

resp-sw-fwd

(Optional) Response pkts sw fwded

req-drop

(Optional) Requests dropped

resp-drop

(Optional) Responses dropped

TABLE_status

(Optional) database status table

st-sender-handle

(Optional) sender handle

type

(Optional) ngoam ping type

state

(Optional) ngoam ping state

__readonly__

(Optional) Read Only

Command Mode

  • /exec

show ngoam pathtrace

show ngoam pathtrace { { statistics { summary | { session { <handle> | all } } } } | { database session { <handle> | all } [ detail ] } } [ __readonly__ [ { TABLE_stats <sender-handle> <last-clear-stats> [ TABLE_stats_fields { <stat-attr> <stat-value> } ] } ] [ { TABLE_summary <last-clear-summary-stats> <tx> <rx> <timeout> <unsent> <req-sw-fwd> <req-drop> <resp-tx> <resp-rx> <resp-unsent> <resp-dup> <resp-sw-fwd> <resp-drop> } ] [ { TABLE_database <db-sender-handle> <db-start-time> <db-end-time> <db-last-clear-stats> <db-tx> <db-rx> <db-timeout> <db-unsent> <db-req-sw-fwd> <db-req-drop> <db-resp-tx> <db-resp-rx> <db-resp-unsent> <db-resp-dup> <db-resp-sw-fwd> <db-resp-drop> { TABLE_db_reply <seq-number> <cli-status> [ <reply-ip> ] [ <reply-ipv6> ] [ <ingress-if> ] [ <ingress-if-state> ] [ <egress-if> ] [ <egress-if-state> ] [ { TABLE_ifstats <if-name> <rx-len> <rx-bytes> <rx-pkt-rate> <rx-byte-rate> <rx-load> <rx-ucast> <rx-mcast> <rx-bcast> <rx-discards> <rx-errors> <rx-unknown> <rx-bandwidth> <tx-len> <tx-bytes> <tx-pkt-rate> <tx-byte-rate> <tx-load> <tx-ucast> <tx-mcast> <tx-bcast> <tx-discards> <tx-errors> <tx-bandwidth> } ] [ <end-row> ] + } } ] ]

Syntax Description

show

Show running system information

ngoam

ngoam

pathtrace

ngoam pathtrace

statistics

ngoam pathtrace statistics

summary

ngoam pathtrace statistics summary

session

ngoam pathtrace session

handle

ngoam pathtrace session handle

all

Display results for all pathtrace sessions

database

ngoam pathtrace results from the database

session

ngoam pathtrace session

all

Display results for all pathtrace sessions

handle

ngoam pathtrace session handle

detail

(Optional) Show detailed stats if present

__readonly__

(Optional) Read Only

TABLE_stats

(Optional) statistics table

sender-handle

(Optional) sender handle

last-clear-stats

(Optional) last clear time for statistics

TABLE_stats_fields

(Optional) statistics entries

stat-attr

(Optional) stats type

stat-value

(Optional) stats value

TABLE_summary

(Optional) statistics summary table

last-clear-summary-stats

(Optional) last clear time for summary statistics

tx

(Optional) summary request sent

rx

(Optional) summary reply received

timeout

(Optional) summary timeout

unsent

(Optional) summary unsent

req-sw-fwd

(Optional) Request pkts sw fwded

req-drop

(Optional) Requests dropped

resp-tx

(Optional) summary resp tx

resp-rx

(Optional) summary resp rx

resp-unsent

(Optional) summary resp unsent

resp-dup

(Optional) Duplicate responses received

resp-sw-fwd

(Optional) Response pkts sw fwded

resp-drop

(Optional) Responses dropped

TABLE_database

(Optional) pathtrace database

db-sender-handle

(Optional) Sender handle

db-start-time

(Optional) Start time

db-end-time

(Optional) End time

db-last-clear-stats

(Optional) Last clear stats

db-tx

(Optional) Tx packets

db-rx

(Optional) Rx packets

db-timeout

(Optional) Timeout

db-unsent

(Optional) Unsent

db-req-sw-fwd

(Optional) Request pkts sw fwded

db-req-drop

(Optional) Requests dropped

db-resp-tx

(Optional) Response tx

db-resp-rx

(Optional) Response Rx

db-resp-unsent

(Optional) Response unsent

db-resp-dup

(Optional) Duplicate response recvd

db-resp-sw-fwd

(Optional) Response pkts sw fwded

db-resp-drop

(Optional) Responses dropped

TABLE_db_reply

(Optional) Replies

seq-number

(Optional) Sequence number

cli-status

(Optional) ngoam pathtrace status

reply-ip

(Optional) ngoam pathrace reply ip

ingress-if

(Optional) Ingress interface

ingress-if-state

(Optional) Ingress interface state

egress-if

(Optional) Egress interface

egress-if-state

(Optional) Egress interface state

end-row

(Optional) Row end

TABLE_ifstats

(Optional) Interface statistics

if-name

(Optional) Interface name

rx-len

(Optional) Rx Length

rx-bytes

(Optional) Rx Bytes

rx-pkt-rate

(Optional) Rx packet rate

rx-byte-rate

(Optional) Rx byte rate

rx-load

(Optional) Rx load

rx-ucast

(Optional) Rx unicast pkts

rx-mcast

(Optional) Rx mcast pkts

rx-bcast

(Optional) Rx bcast pkts

rx-discards

(Optional) Rx discards

rx-errors

(Optional) Rx errors

rx-unknown

(Optional) Rx unknown

rx-bandwidth

(Optional) Rx bandwidth

tx-len

(Optional) Tx Length

tx-bytes

(Optional) Tx Bytes

tx-pkt-rate

(Optional) Tx packet rate

tx-byte-rate

(Optional) Tx byte rate

tx-load

(Optional) Tx load

tx-ucast

(Optional) Tx unicast pkts

tx-mcast

(Optional) Tx mcast pkts

tx-bcast

(Optional) Tx bcast pkts

tx-discards

(Optional) Tx discards

tx-errors

(Optional) Tx unknown

tx-bandwidth

(Optional) Tx bandwidth

Command Mode

  • /exec

show ngoam probe

show ngoam probe { { statistics { summary | { session { <handle> | all } } } } } [ __readonly__ [ TABLE_stats { <sender-handle> <transaction-id> <dst-vip> <vni> <oam-type> <flow-str> <last-clear-stats> <req-sent> <req-not-sent> } <statistics-end> ] [ TABLE_summary { <last-clear-summary-stats> <tx> <rx> <timeout> <unsent> <resp-tx> <resp-rx> <resp-unsent> } ] ]

Syntax Description

show

Show running system information

ngoam

ngoam

probe

ngoam probe

statistics

ngoam probe statistics

summary

ngoam probe statistics summary

session

ngoam probe session

handle

ngoam probe session handle

all

Display results for all probe sessions

TABLE_stats

(Optional) statistics table

sender-handle

(Optional) sender handle

transaction-id

(Optional) Transaction Identifier

dst-vip

(Optional) Destination Vtep ip address

vni

(Optional) vxlan header vni

oam-type

(Optional) draft pang oam type

flow-str

(Optional) 128 byte flow string.

last-clear-stats

(Optional) last clear time for statistics

req-sent

(Optional) request sent

req-not-sent

(Optional) request not sent or failed

statistics-end

(Optional) statistics table end marker

TABLE_summary

(Optional) statistics summary table

last-clear-summary-stats

(Optional) last clear time for summary statistics

tx

(Optional) summary request sent

rx

(Optional) summary reply received

timeout

(Optional) summary timeout

unsent

(Optional) summary unsent

resp-tx

(Optional) summary resp tx

resp-rx

(Optional) summary resp rx

resp-unsent

(Optional) summary resp unsent

__readonly__

(Optional) Read Only

Command Mode

  • /exec

show ngoam traceroute statistics

show ngoam traceroute statistics { summary | { session { <handle> | all } } } [ __readonly__ [ TABLE_stats { <sender-handle> <last-clear-stats> TABLE_stats_attr { <stat-attr> <stat-value> } } ] [ TABLE_summary { <last-clear-summary-stats> <tx> <rx> <timeout> <unsent> <resp-tx> <resp-rx> <resp-unsent> <resp-dup> } ] ]

Syntax Description

show

Show running system information

ngoam

ngoam

traceroute

ngoam traceroute

statistics

ngoam traceroute statistics

summary

ngoam traceroute statistics summary

session

ngoam traceroute session

handle

ngoam traceroute session handle

all

Display results for all traceroute sessions

TABLE_stats

(Optional) statistics table

sender-handle

(Optional) sender handle

last-clear-stats

(Optional) last clear time for statistics

TABLE_stats_attr

(Optional) Stats attributes table

stat-attr

(Optional) stats type

stat-value

(Optional) stats value

TABLE_summary

(Optional) statistics summary table

last-clear-summary-stats

(Optional) last clear time for summary statistics

tx

(Optional) summary request sent

rx

(Optional) summary reply received

timeout

(Optional) summary timeout

unsent

(Optional) summary unsent

resp-tx

(Optional) summary resp tx

resp-rx

(Optional) summary resp rx

resp-unsent

(Optional) summary resp unsent

resp-dup

(Optional) Duplicate responses received

__readonly__

(Optional) Read Only

Command Mode

  • /exec

show ngoam xconnect session

show ngoam xconnect session { <id> [ iodb ] | all [ dbdump ] } [ __readonly__ [ TABLE_xc_db_summary { [ <legend> ] <vlan-id> <peer-ip> <vni> <db-state> <local-if> <local-if-state> <remote-if> <remote-if-state> [ <end-row> ] + } + ] [ ENTRY_xc_db_detail { <detail> <d-vlan-id> <d-peer-ip> [ <peer-name> ] <d-vni> <d-db-state> <last-state-change-ts> <d-local-if> <d-local-if-state> <vpc-if> <vpc-if-state> <remote-if-detail> <remote-if-detail-state> <remote-vpc-if> <remote-vpc-if-state> [ <d-end-row> ] + } ] ]

Syntax Description

show

Show running system information

ngoam

ngoam information

xconnect

crossconnect info

session

xc session id

id

Vlan-id of the xc

iodb

(Optional) Iodb

all

show summary info for all sessions

__readonly__

(Optional) Read Only

TABLE_xc_db_summary

(Optional) XC Db table

ENTRY_xc_db_detail

(Optional) XC Db detail

detail

(Optional) Detail or not

vlan-id

(Optional) Vlan id

d-vlan-id

(Optional) Vlan id

vni

(Optional) vni

d-vni

(Optional) vni

local-if

(Optional) Interface

d-local-if

(Optional) Interface

local-if-state

(Optional) Interface state

d-local-if-state

(Optional) Interface state

remote-if

(Optional) Remote interface

remote-if-state

(Optional) Remote interface state

remote-if-detail

(Optional) Remote interface

remote-if-detail-state

(Optional) Remote interface state

vpc-if

(Optional) Interface

vpc-if-state

(Optional) Interface state

remote-vpc-if

(Optional) Remote vpc interface

remote-vpc-if-state

(Optional) Remote vpc interface state

db-state

(Optional) XC state

d-db-state

(Optional) XC state

last-state-change-ts

(Optional) Last state change timestamp

peer-ip

(Optional) Peer ip

d-peer-ip

(Optional) Peer ip

peer-name

(Optional) Peer name

end-row

(Optional) end row

d-end-row

(Optional) end row

legend

(Optional) legend

dbdump

(Optional) Dump the whole database

Command Mode

  • /exec

show npv external-interface-usage

show npv external-interface-usage [ server-interface <if0> ] [ __readonly__ { TABLE_intf_usage <svr_intf> <ext_intf> } ]

Syntax Description

show

Show running system information

npv

Show information about NPV

external-interface-usage

Show external interface usage by server interfaces

server-interface

(Optional) Show external interface usage by a server interface

if0

(Optional)

__readonly__

(Optional) Read Only

TABLE_intf_usage

(Optional) External Interfaces Usage Table

svr_intf

(Optional) Server Interface

ext_intf

(Optional) External Interface

Command Mode

  • /exec

show npv flogi-table

show npv flogi-table [ { interface <if0> | vsan <i0> } ] [ __readonly__ [ [ TABLE_flogi <svr_intf> <vsan_id> <fcid> <pwwn> <ext_intf> <nwwn> ] [ <flogi_count> ] ] ]

Syntax Description

show

Show running system information

npv

Show information about NPV

flogi-table

Show information about FLOGI sessions

interface

(Optional) Show information about FLOGI sessions for a server interface

if0

(Optional)

vsan

(Optional) Show information about FLOGI sessions for a VSAN

i0

(Optional)

__readonly__

(Optional) Read Only

TABLE_flogi

(Optional) FLOGI Table

svr_intf

(Optional) Server Interface

vsan_id

(Optional) VSAN ID

fcid

(Optional) FLOGI FCID

pwwn

(Optional) The PWWN

ext_intf

(Optional) External Interface

nwwn

(Optional) The NWWN

flogi_count

(Optional) Total FLOGI Count

Command Mode

  • /exec

show npv status

show npv status [ vsan <i0> ] [ __readonly__ [ [ <npiv_status> ] [ <load_balance> ] [ { TABLE_extintf <ext_intf> [ <ext_vsan> ] [ <ext_fcid> ] <ext_state> [ { TABLE_vsan <vsan_vsan> <vsan_state> [ <vsan_fcid> ] } ] } ] <ext_intf_count> [ { TABLE_svrintf <svr_intf> <svr_vsan> <svr_state> } ] <svr_intf_count> ] ]

Syntax Description

show

Show running system information

npv

Show information about NPV

status

Show NPV status

vsan

(Optional) Show NPV status for a specific VSAN

i0

(Optional)

__readonly__

(Optional) Read Only

npiv_status

(Optional) NPIV enable/disable status

load_balance

(Optional) disruptive load balance status

TABLE_extintf

(Optional) External Interfaces Table

ext_intf

(Optional) External Interface

ext_vsan

(Optional) External Interface VSAN

ext_fcid

(Optional) External Interface FCID

ext_state

(Optional) External Interface State

TABLE_vsan

(Optional) External Interfaces VSAN Table

vsan_vsan

(Optional) External Interface VSAN

vsan_state

(Optional) VSAN State

vsan_fcid

(Optional) VSAN FCID

ext_intf_count

(Optional) External Interface count

TABLE_svrintf

(Optional) Server Interfaces Table

svr_intf

(Optional) Server Interface

svr_vsan

(Optional) Server Interface VSAN

svr_state

(Optional) Server Interface State

svr_intf_count

(Optional) Server Interface count

Command Mode

  • /exec

show npv traffic-map

show npv traffic-map [ server-interface <if0> ] [ __readonly__ [ { TABLE_traffic_map <svr_intf> <ext_intf> } ] ]

Syntax Description

show

Show running system information

npv

Show information about NPV

traffic-map

Show information about Traffic Map

server-interface

(Optional) Show information about Traffic map for a server interface

if0

(Optional)

__readonly__

(Optional) Read Only

TABLE_traffic_map

(Optional) Traffic Map Table

svr_intf

(Optional) Server Interface

ext_intf

(Optional) External Interface

Command Mode

  • /exec

show ntp access-groups

show ntp access-groups [ __readonly__ [ <matchall> ] [ { TABLE_accessgroups <accesslist> [ <type> ] } ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

access-groups

Display NTP access groups

__readonly__

(Optional)

matchall

(Optional) matchall

TABLE_accessgroups

(Optional) accessgroups

accesslist

(Optional) accesslist

type

(Optional) type

Command Mode

  • /exec

show ntp authentication-keys

show ntp authentication-keys [ __readonly__ [ { TABLE_authkeys <Authkey> [ <MD5String> ] } ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

authentication-keys

Display authentication keys

__readonly__

(Optional)

TABLE_authkeys

(Optional) authentication keys

Authkey

(Optional) authentication key

MD5String

(Optional) password

Command Mode

  • /exec

show ntp authentication-status

show ntp authentication-status [ __readonly__ [ <authentication> ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

authentication-status

NTP Authentication Status

__readonly__

(Optional)

authentication

(Optional) authentication enabled/disabled

Command Mode

  • /exec

show ntp information

show ntp information [ __readonly__ [ <system_type> ] [ <software_version> ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

information

Show ntp information

__readonly__

(Optional)

system_type

(Optional) Ntp System Type

software_version

(Optional) Ntp Software Version

Command Mode

  • /exec

show ntp logging-status

show ntp logging-status [ __readonly__ [ <loggingstatus> ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

logging-status

Display NTP logging status

__readonly__

(Optional)

loggingstatus

(Optional) logging enabled/disabled

Command Mode

  • /exec

show ntp peer-status

show ntp peer-status [ __readonly__ [ <totalpeers> ] [ { TABLE_peersstatus <syncmode> <remote> <local> <st> <poll> <reach> <delay> [ <vrf> ] } ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

peer-status

Show the status for all the server/peers

__readonly__

(Optional)

totalpeers

(Optional) totalpeers

TABLE_peersstatus

(Optional) peersstatus

syncmode

(Optional) peermode

remote

(Optional) remote addr

local

(Optional) local addr

st

(Optional) stratum

poll

(Optional) ntp poll

reach

(Optional) reach

delay

(Optional) delay

vrf

(Optional) vrf name

Command Mode

  • /exec

show ntp peers

show ntp peers [ __readonly__ [ { TABLE_peers <PeerIPAddress> <serv_peer> <conf_flag> } ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

peers

Show all the peers.

__readonly__

(Optional)

TABLE_peers

(Optional) peers

PeerIPAddress

(Optional) peer Ip addr

serv_peer

(Optional) server or peer

conf_flag

(Optional) configured or dynamic

Command Mode

  • /exec

show ntp rts-update

show ntp rts-update [ __readonly__ [ <rtsupdate> ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

rts-update

Show if the RTS update is enabled

__readonly__

(Optional)

rtsupdate

(Optional) rts update enabled/disabled

Command Mode

  • /exec

show ntp session status

show ntp session status [ __readonly__ [ <session_status> ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

session

Show the session information

status

Show the session status

__readonly__

(Optional)

session_status

(Optional) last session status

Command Mode

  • /exec

show ntp source-interface

show ntp source-interface [ __readonly__ [ <sourceinterface> ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

source-interface

Source interface configured

__readonly__

(Optional)

sourceinterface

(Optional) source interface

Command Mode

  • /exec

show ntp source

show ntp source [ __readonly__ [ { TABLE_sourceip <sourceip> } ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

source

Source IP address configured

__readonly__

(Optional)

TABLE_sourceip

(Optional) source ip table

sourceip

(Optional) source ip addr

Command Mode

  • /exec

show ntp statistics

show ntp statistics { [ io ] | [ local ] | [ memory ] | peer { ipaddr { <ipv4_0> | <ipv6_1> } | name <s0> } } [ __readonly__ [ { <iotimesincereset> <ioreceivebuffers> <iofreereceivebuffers> <iousedreceivebuffers> <iolowwaterrefills> <iodroppedpackets> <ioignoredpackets> <ioreceivedpackets> <iopacketssent> <iopacketsnotsent> <iointerruptshandled> <ioreceivedbyint> } ] [ { <localsystemuptime> <localtimesincereset> <localoldversionpackets> <localnewversionpackets> <localunknownversionnumber> <localbadpacketformat> <localpacketsprocessed> <localbadauthentication> [ <localpacketsrejected> ] } ] [ { <memtimesincereset> <memtotalpeermemory> <memfreepeermemory> <memcallstofindpeer> <memnewpeerallocations> <mempeerdemobilizations> <memhashtablecounts> } ] [ { <peeripremotehost> <peeriplocalinterface> <peeriptimelastreceived> <peeriptimeuntilnextsend> <peeripreachabilitychange> <peerippacketssent> <peerippacketsreceived> <peeripbadauthentication> <peeripbogusorigin> <peeripduplicate> <peeripbaddispersion> <peeripbadreferencetime> <peeripcandidateorder> } ] [ { <peernameremotehost> <peernamelocalinterface> <peernametimelastreceived> <peernametimeuntilnextsend> <peernamereachabilitychange> <peernamepacketssent> <peernamepacketsreceived> <peernamebadauthentication> <peernamebogusorigin> <peernameduplicate> <peernameduplicate> <peernamebaddispersion> <peernamebadreferencetime> <peernamecandidateorder> } ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

statistics

Show the NTP statistics

io

(Optional) Show the input-output statistics.

local

(Optional) Show the counters maintained by the local NTP.

memory

(Optional) Show the statistics counters related to memory code.

peer

Show the per-peer statistics counter of a peer.

ipaddr

Peer's IP address

ipv4_0

name

Peer's Name

s0

__readonly__

(Optional)

iotimesincereset

(Optional) time since reset

ioreceivebuffers

(Optional) receive buffers

iofreereceivebuffers

(Optional) free receive buffers

iousedreceivebuffers

(Optional) used receive buffers

iolowwaterrefills

(Optional) low water refills

iodroppedpackets

(Optional) dropped packets

ioignoredpackets

(Optional) ignored packets

ioreceivedpackets

(Optional) received packets

iopacketssent

(Optional) packets sent

iopacketsnotsent

(Optional) packets not sent

iointerruptshandled

(Optional) interrupts handled

ioreceivedbyint

(Optional) received by int

localsystemuptime

(Optional) system up time

localtimesincereset

(Optional) time since reset

localoldversionpackets

(Optional) old version packets

localnewversionpackets

(Optional) new version packets

localunknownversionnumber

(Optional) unknown version number

localbadpacketformat

(Optional) bad packet format

localpacketsprocessed

(Optional) packets processed

localbadauthentication

(Optional) bad authentication

localpacketsrejected

(Optional) packets rejected

memtimesincereset

(Optional) time since reset

memtotalpeermemory

(Optional) total peer memory

memfreepeermemory

(Optional) free peer memory

memcallstofindpeer

(Optional) calls to find peer

memnewpeerallocations

(Optional) new peer allocations

mempeerdemobilizations

(Optional) peer demobilizations

memhashtablecounts

(Optional) hash table counts

peeripremotehost

(Optional) peeripremotehost

peeriplocalinterface

(Optional) peeriplocalinterface

peeriptimelastreceived

(Optional) peeriptimelastreceived

peeriptimeuntilnextsend

(Optional) peeriptimeuntilnextsend

peeripreachabilitychange

(Optional) peeripreachabilitychange

peerippacketssent

(Optional) peerippacketssent

peerippacketsreceived

(Optional) peerippacketsreceived

peeripbadauthentication

(Optional) peeripbadauthentication

peeripbogusorigin

(Optional) peeripbogusorigin

peeripduplicate

(Optional) peeripduplicate

peeripbaddispersion

(Optional) peeripbaddispersion

peeripbadreferencetime

(Optional) peeripbadreferencetime

peeripcandidateorder

(Optional) peeripcandidateorder

peernameremotehost

(Optional) peernameremotehost

peernamelocalinterface

(Optional) peernamelocalinterface

peernametimelastreceived

(Optional) peernametimelastreceived

peernametimeuntilnextsend

(Optional) peernametimeuntilnextsend

peernamereachabilitychange

(Optional) peernamereachabilitychange

peernamepacketssent

(Optional) peernamepacketssent

peernamepacketsreceived

(Optional) peernamepacketsreceived

peernamebadauthentication

(Optional) peernamebadauthentication

peernamebogusorigin

(Optional) peernamebogusorigin

peernameduplicate

(Optional) peernameduplicate

peernamebaddispersion

(Optional) peernamebaddispersion

peernamebadreferencetime

(Optional) peernamebadreferencetime

peernamecandidateorder

(Optional) peernamecandidateorder

Command Mode

  • /exec

show ntp status

show ntp status [ __readonly__ [ <distribution> ] [ <operational_state> ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

status

Show the NTP distribution status

__readonly__

(Optional)

distribution

(Optional) distribution enabled/disabled

operational_state

(Optional) last operation status

Command Mode

  • /exec

show ntp trusted-keys

show ntp trusted-keys [ __readonly__ [ { TABLE_trustkeys <key> } ] ]

Syntax Description

show

Show running system information

ntp

Show NTP information

trusted-keys

Display trusted keys

__readonly__

(Optional)

TABLE_trustkeys

(Optional) trusted keys

key

(Optional) trusted key

Command Mode

  • /exec

show nxapi-server logs

show nxapi-server logs

Syntax Description

show

Show running system information

nxapi-server

Show NX-API Server

logs

Show NX-API Server logs

Command Mode

  • /exec

show nxapi

show nxapi [ __readonly__ <nxapi_status> [ configuration_error <c_error> ] [ <http_port> ] [ <https_port> <ssl_issuer> <ssl_enddate> ] ]

Syntax Description

show

Show running system information

nxapi

Show nxapi status

__readonly__

(Optional)

nxapi_status

(Optional) NX-API enabled status

configuration_error

(Optional) config syntax error

c_error

(Optional) confg syntax error

http_port

(Optional) Configured HTTP port

https_port

(Optional) Configured HTTPS port

ssl_issuer

(Optional) Issuer information for current certificate

ssl_enddate

(Optional) Expiration date of current certificate

Command Mode

  • /exec

show nxapi syntax

show nxapi syntax <cli>

Syntax Description

show

Show running system information

nxapi

Show nxapi status

syntax

Display syntax for given command

cli

the exact cli to look-up

Command Mode

  • /exec