callhome common

Description: Callhome common policy configuration mode

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# callhome common

callhome test info|notice|emergency|alert|critical|error|debug|warning

Description: Send callhome test message

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# callhome test info|notice|emergency|alert|critical|error|debug|warning

callhome test info|notice|emergency|alert|critical|error|debug|warning node <Source node>

Description: Source node

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# callhome test info|notice|emergency|alert|critical|error|debug|warning node <Source node>

catalog-version <version>

Description: Change catalog version

Syntax:

Command Mode: firmware : Firmware upgrade configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# firmware
(config-firmware)# catalog-version <version>

cdp enable|default

Description: Configure CDP parameters on DVS uplink ports

Syntax:

Command Mode: configure-dvs : Configure a VMWare Domain as DVS type

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-dvs
(config-vmware-dvs)# cdp enable|default

cdp enable|default

Description: Configure CDP parameters on AVS/AVE uplink ports

Syntax:

Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-avs
(config-vmware-avs)# cdp enable|default

cdp enable|default

Description: Configure CDP parameters on AVS/AVE uplink ports

Syntax:

Command Mode: configure-ave : Configure a Cisco AVE domain

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-ave
(config-vmware-ave)# cdp enable|default

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: template policy-group : Configure Policy Group Parameters

Command Path:

# configure [['terminal', 't']]
(config)# template policy-group <WORD>
(config-pol-grp-if)# cdp enable

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: template port-channel : Configure Port-Channel Parameters

Command Path:

# configure [['terminal', 't']]
(config)# template port-channel <WORD>
(config-po-ch-if)# cdp enable

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: template spine-interface-policy-group : Configure Policy Group Parameters

Command Path:

# configure [['terminal', 't']]
(config)# template spine-interface-policy-group <WORD>
(config-spine-if-pol-grp)# cdp enable

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: interface ethernet : Ethernet IEEE 802.3z

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# interface ethernet <ifRange>
(config-leaf-if)# cdp enable

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: interface port-channel : Port Channel interface

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# interface port-channel <WORD> [fex <fex>]
(config-leaf-if)# cdp enable

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: interface ethernet : Ethernet IEEE 802.3z

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# interface ethernet <ifRange>
(config-leaf-if)# cdp enable

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: interface port-channel : Port Channel interface

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# interface port-channel <WORD> [fex <fex>]
(config-leaf-if)# cdp enable

cdp enable

Description: Configure CDP interface parameters

Syntax:

Command Mode: interface : Provide VPC Name

Command Path:

# configure [['terminal', 't']]
(config)# vpc context leaf <101-4000> <101-4000> [fex <fex>]
(config-vpc)# interface vpc <WORD> [fex <fex>]
(config-vpc-if)# cdp enable

cert-chain <WORD>

Description: Set The PEM-encoded chain of trust from the trustpoint to a trusted root authority.

Syntax:

Command Mode: crypto ca : Configure certificate authority related information

Command Path:

# configure [['terminal', 't']]
(config)# crypto ca <WORD>
(config-ca)# cert-chain <WORD>

cert <CERTIFICATE>

Description: Provide a certificate, that contains public key and signed information.

Syntax:

Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate

Command Path:

# configure [['terminal', 't']]
(config)# crypto keyring <WORD>
(config-keyring)# cert <CERTIFICATE>

certificate <WORD>

Description: Create AAA user certificate in X.509 format.

Syntax:

Command Mode: username : Create a locally-authenticated user account

Command Path:

# configure [['terminal', 't']]
(config)# username <WORD>
(config-username)# certificate <WORD>

channel-group <WORD> [vpc]

Description: Create Port Channel

Syntax:

Command Mode: leaf-interface-group : Configure Leaf Interface Group

Command Path:

# configure [['terminal', 't']]
(config)# leaf-interface-profile <WORD>
(config-leaf-if-profile)# leaf-interface-group <WORD>
(config-leaf-if-group)# channel-group <WORD> [vpc]

channel-group <WORD> [vpc]

Description: Configure Port Channel on Fex

Syntax:

Command Mode: fex-interface-group : Configure Fex Interface Group

Command Path:

# configure [['terminal', 't']]
(config)# fex-profile <WORD>
(config-fex-profile)# fex-interface-group <WORD>
(config-fex-if-group)# channel-group <WORD> [vpc]

channel-group <WORD> [vpc]

Description: Associate a Channel Group to this Interface

Syntax:

Command Mode: interface ethernet : Ethernet IEEE 802.3z

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# interface ethernet <ifRange>
(config-leaf-if)# channel-group <WORD> [vpc]

channel-group <WORD> [vpc]

Description: Associate a Channel Group to this Interface

Syntax:

Command Mode: interface ethernet : Ethernet IEEE 802.3z

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# interface ethernet <ifRange>
(config-leaf-if)# channel-group <WORD> [vpc]

channel-mode on|active|passive|mac-pinning

Description: Configure LACP mode override on DVS uplink ports

Syntax:

Command Mode: configure-dvs : Configure a VMWare Domain as DVS type

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-dvs
(config-vmware-dvs)# channel-mode on|active|passive|mac-pinning

channel-mode on|active|passive|mac-pinning

Description: Configure LACP mode override on AVS/AVE uplink ports

Syntax:

Command Mode: configure-avs : Configure a VMWare Domain as AVS (N1K) type

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-avs
(config-vmware-avs)# channel-mode on|active|passive|mac-pinning

channel-mode on|active|passive|mac-pinning

Description: Configure LACP mode override on AVS/AVE uplink ports

Syntax:

Command Mode: configure-ave : Configure a Cisco AVE domain

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-ave
(config-vmware-ave)# channel-mode on|active|passive|mac-pinning

channel-mode on|active|passive|mac-pinning

Description: Configure channeling mode

Syntax:

Command Mode: template port-channel : Configure Port-Channel Parameters

Command Path:

# configure [['terminal', 't']]
(config)# template port-channel <WORD>
(config-po-ch-if)# channel-mode on|active|passive|mac-pinning

channel-mode on|active|passive|mac-pinning

Description: Configure channeling mode

Syntax:

Command Mode: interface port-channel : Port Channel interface

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# interface port-channel <WORD> [fex <fex>]
(config-leaf-if)# channel-mode on|active|passive|mac-pinning

channel-mode on|active|passive|mac-pinning

Description: Configure channeling mode

Syntax:

Command Mode: interface port-channel : Port Channel interface

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# interface port-channel <WORD> [fex <fex>]
(config-leaf-if)# channel-mode on|active|passive|mac-pinning

channel-mode on|active|passive|mac-pinning

Description: Configure channeling mode

Syntax:

Command Mode: interface : Provide VPC Name

Command Path:

# configure [['terminal', 't']]
(config)# vpc context leaf <101-4000> <101-4000> [fex <fex>]
(config-vpc)# interface vpc <WORD> [fex <fex>]
(config-vpc-if)# channel-mode on|active|passive|mac-pinning

cif cluster <WORD> device <WORD> device-interface <WORD>

Description: Configure Relation to Cluster Interface

Syntax:

Command Mode: l1l2redir-dest : Configure l1l2redirect destination

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# svcredir-pol <WORD>
(svcredir-pol)# l1l2redir-dest <WORD>
(config-l1l2redir-dest)# cif cluster <WORD> device <WORD> device-interface <WORD>

cipher-suite <arg>

Description: Configure SAP negotiation algorithm

Syntax:

Command Mode: template macsec access|fabric security-policy : Configure MAC security policy parameters

Command Path:

# configure [['terminal', 't']]
(config)# template macsec access|fabric security-policy <WORD>
(config-macsec-param)# cipher-suite <>

ciphers <WORD>

Description: HTTPS cipher suite

Syntax:

Command Mode: https : HTTPS communication policy group

Command Path:

# configure [['terminal', 't']]
(config)# comm-policy <WORD>
(config-comm-policy)# https
(config-https)# ciphers <WORD>

clear-encryption-key

Description: Clears AES encryption key

Command Mode: crypto aes : AES encryption configuration

Command Path:

# configure [['terminal', 't']]
(config)# crypto aes
(config-aes)# clear-encryption-key

clear-pwd-history

Description: Clears the password history of a locally-authenticated user

Command Mode: username : Create a locally-authenticated user account

Command Path:

# configure [['terminal', 't']]
(config)# username <WORD>
(config-username)# clear-pwd-history

clear core-status controller <NUMBER> <WORD>

Description: Remove exported core status and files for controllers

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear core-status controller <NUMBER> <WORD>

clear core-status switch <NUMBER> <WORD>

Description: Remove exported core status and files for switches

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear core-status switch <NUMBER> <WORD>

clear core controller <NUMBER> <WORD>

Description: Remove core metadata information generated at a controller

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear core controller <NUMBER> <WORD>

clear core switch <NUMBER> <WORD>

Description: Remove core metadata information generated at a switch

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear core switch <NUMBER> <WORD>

clear endpoints leaf <node-id> tenant <tenant-name> bridge-domain <bd-name>

Description: Clear Bridge-Domain Hosting the endpoints

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear endpoints leaf <WORD> tenant <WORD> bridge-domain <WORD>

clear endpoints leaf <node-id> tenant <tenant-name> bridge-domain <bd-name> vlan <NUMBER>

Description: Clear VLAN Hosting the endpoints

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear endpoints leaf <WORD> tenant <WORD> bridge-domain <WORD> vlan <NUMBER>

clear endpoints leaf <node-id> tenant <tenant-name> vrf <vrf-name>

Description: Clear VRF Hosting the endpoints

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear endpoints leaf <WORD> tenant <WORD> vrf <WORD>

clear firmware upgrade scheduler-restrictions

Description: Clear firmware upgrade scheduler restrictions

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear firmware upgrade scheduler-restrictions

clear snapshot file <WORD>

Description: Remove snapshot file

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear snapshot file <WORD>

clear snapshot job <WORD>

Description: Remove snapshot job

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear snapshot job <WORD>

clear techsupport controllers <NUMBER> <WORD>

Description: Clear techsupport status for controllers

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear techsupport controllers <NUMBER> <WORD>

clear techsupport switch <NUMBER> <WORD>

Description: Clear techsupport status for switch

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear techsupport switch <NUMBER> <WORD>

clear tenant <WORD>

Description: Clear Tenant related information

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD>

clear tenant <WORD> bridge-domain <WORD>

Description: Show Bridge-domain Information

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD> bridge-domain <WORD>

clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics arp

Description: Clear Bridge-domain First Hop Security ARP Statistics

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics arp

clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics dhcpv4

Description: Clear Bridge-domain First Hop Security DHCPv6 Statistics

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics dhcpv4

clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics dhcpv6

Description: Clear Bridge-domain First Hop Security DHCPv6 Statistics

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics dhcpv6

clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics neighbor-discovery

Description: Clear Bridge-domain First Hop Security Neighbor Discovery Statistics

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD> bridge-domain <WORD> first-hop-security statistics neighbor-discovery

clear tenant <WORD> bridge-domain <WORD> first-hop-security violation-event all

Description: Clear all FHS Violations

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD> bridge-domain <WORD> first-hop-security violation-event all

clear tenant <WORD> bridge-domain <WORD> first-hop-security violation-event feature <WORD> origin <WORD> type <WORD> ip <WORD> mac <WORD> pctag <WORD>

Description: Specify FHS Violation feature type

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear tenant <WORD> bridge-domain <WORD> first-hop-security violation-event feature <WORD> origin <WORD> type <WORD> ip <WORD> mac <WORD> pctag <WORD>

clear troubleshoot report <WORD>

Description: Remove non-pending reports of a troubleshoot session

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# clear troubleshoot report <WORD>

cli-only-mode-enable

Description: Enable HTTP CLI only mode

Command Mode: http : HTTP communication policy group

Command Path:

# configure [['terminal', 't']]
(config)# comm-policy <WORD>
(config-comm-policy)# http
(config-http)# cli-only-mode-enable

cli-only-mode-enable

Description: Enable HTTPs CLI only mode

Command Mode: https : HTTPS communication policy group

Command Path:

# configure [['terminal', 't']]
(config)# comm-policy <WORD>
(config-comm-policy)# https
(config-https)# cli-only-mode-enable

client-cert-ca <ca-name>

Description: Use specified CA for the HTTPS client certificate auth

Syntax:

Command Mode: https : HTTPS communication policy group

Command Path:

# configure [['terminal', 't']]
(config)# comm-policy <WORD>
(config-comm-policy)# https
(config-https)# client-cert-ca <ca-name>

client-cert-state-enable

Description: Enable the state of the HTTPS communication service

Command Mode: https : HTTPS communication policy group

Command Path:

# configure [['terminal', 't']]
(config)# comm-policy <WORD>
(config-comm-policy)# https
(config-https)# client-cert-state-enable

clock display-format local|utc

Description: Configure Clock Display Format

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# clock display-format local|utc

clock show-offset enable

Description: Enable/Disable Display of the Offset

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# clock show-offset enable

clock timezone <timeZone>

Description: Configure clock timezone

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# clock timezone <timeZone>

cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] [host <host>] [management-ip <management-ip>] [gateway <gateway>] [subnet-mask <subnet-mask>] [management-port <management-port>] [management-vnic <management-vnic>] [mgmt-portgroup <mgmt-portgroup>] [ha-portgroup <ha-portgroup>] [ha-vnic <ha-vnic>] [user-name <WORD>]

Description: Configure L4-L7 Cluster Device

Syntax:

Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [switching-mode <switching-mode>] [service <service>] [function <function>] [context <context>] [trunking <enable|disable>] [vm-instantiation-policy <vm-instantiation-policy>]
(config-cluster)# cluster-device <WORD> [vcenter <WORD>] [vm <WORD>] [host <host>] [management-ip <management-ip>] [gateway <gateway>] [subnet-mask <subnet-mask>] [management-port <management-port>] [management-vnic <management-vnic>] [mgmt-portgroup <mgmt-portgroup>] [ha-portgroup <ha-portgroup>] [ha-vnic <ha-vnic>] [user-name <WORD>]

cluster-interface <WORD> [vlan <NUMBER>]

Description: Configure L4-L7 Cluster Interface

Syntax:

Command Mode: l4l7 cluster name : Add a L4-L7 Service Device Cluster

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 cluster name <WORD> type <type> vlan-domain <domain-name> [switching-mode <switching-mode>] [service <service>] [function <function>] [context <context>] [trunking <enable|disable>] [vm-instantiation-policy <vm-instantiation-policy>]
(config-cluster)# cluster-interface <WORD> [vlan <NUMBER>]

collect <arg>

Description: Configure collect

Syntax:

Command Mode: flow record : Configure Netflow Record

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# flow record <WORD>
(config-tn-flow-record)# collect <>

collect <arg>

Description: Configure collect

Syntax:

Command Mode: flow record : Configure Netflow Record

Command Path:

# configure [['terminal', 't']]
(config)# flow record <WORD>
(config-flow-record)# collect <>

comm-policy <WORD>

Description: Configure any communication policy, ssh/telnet/shellinabox/http/https

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# comm-policy <WORD>

community-list expanded <WORD> <LINE>

Description: Configure expanded community list templates

Syntax:

Command Mode: template route group : Configure Route Group

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# template route group <WORD> tenant <WORD>
(config-route-group)# community-list expanded <WORD> <LINE>

community-list expanded <WORD> <LINE>

Description: Configure expanded community list templates

Syntax:

Command Mode: template route group : Configure Route Group

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# template route group <WORD> tenant <WORD>
(config-route-group)# community-list expanded <WORD> <LINE>

community-list standard <WORD> ASN2:NN

Description: Configure standard community list templates

Syntax:

Command Mode: template route group : Configure Route Group

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# template route group <WORD> tenant <WORD>
(config-route-group)# community-list standard <WORD> ASN2:NN

community-list standard <WORD> ASN2:NN

Description: Configure standard community list templates

Syntax:

Command Mode: template route group : Configure Route Group

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# template route group <WORD> tenant <WORD>
(config-route-group)# community-list standard <WORD> ASN2:NN

compatibility-check

Description: Check for compatibility

Command Mode: controller-group : Controller Upgrade Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# firmware
(config-firmware)# controller-group
(config-firmware-controller)# compatibility-check

compatibility-check

Description: Check for compatibility

Command Mode: switch-group : Create switch firmware upgrade policy

Command Path:

# configure [['terminal', 't']]
(config)# firmware
(config-firmware)# switch-group <WORD>
(config-firmware-switch)# compatibility-check

conf-offset <arg>

Description: Configure confidentiality offset for encryption

Syntax:

Command Mode: template macsec access|fabric security-policy : Configure MAC security policy parameters

Command Path:

# configure [['terminal', 't']]
(config)# template macsec access|fabric security-policy <WORD>
(config-macsec-param)# conf-offset <>

config-file <config-file>

Description: Select configuration file SVM instantiation policy

Syntax:

Command Mode: inst-pol : Configure L4L7 service vm instantiation policy

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# inst-pol <WORD> <vmm-domain> <ctrlr> <vm-template> <resource-pool> <datastore>
(config-inst-pol)# config-file <config-file>

configure-ave

Description: Configure a Cisco AVE domain

Command Mode: vmware-domain : Create a VMM VMWare Domain

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-ave

configure-avs

Description: Configure a VMWare Domain as AVS (N1K) type

Command Mode: vmware-domain : Create a VMM VMWare Domain

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-avs

configure-dvs

Description: Configure a VMWare Domain as DVS type

Command Mode: vmware-domain : Create a VMM VMWare Domain

Command Path:

# configure [['terminal', 't']]
(config)# vmware-domain <WORD> [delimiter <WORD>] [access-mode <access-mode>]
(config-vmware)# configure-dvs

configure [['terminal', 't']]

Description: Configuration Mode

Syntax:

Command Mode: exec : Exec Mode

Command Path:

# configure [['terminal', 't']]

connection <WORD> [peerconnect <Peer connectivity>] intra-service service1 <WORD> connector1 <WORD> service2 <WORD> connector2 <WORD>

Description: Configure L4-L7 connection between service nodes

Syntax:

Command Mode: l4l7 graph : Configure L4-L7 Service Graph

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
(config-graph)# connection <WORD> [peerconnect <Peer connectivity>] intra-service service1 <WORD> connector1 <WORD> service2 <WORD> connector2 <WORD>

connection <WORD> [peerconnect <Peer connectivity>] intra-service service1 <WORD> connector1 <WORD> service2 <WORD> connector2 <WORD> copyservice <WORD> connector <WORD>

Description: Configure copy node and connector

Syntax:

Command Mode: l4l7 graph : Configure L4-L7 Service Graph

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
(config-graph)# connection <WORD> [peerconnect <Peer connectivity>] intra-service service1 <WORD> connector1 <WORD> service2 <WORD> connector2 <WORD> copyservice <WORD> connector <WORD>

connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer service <WORD> connector <WORD>

Description: Configure service node that connects to a terminal node

Syntax:

Command Mode: l4l7 graph : Configure L4-L7 Service Graph

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
(config-graph)# connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer service <WORD> connector <WORD>

connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer service <WORD> connector <WORD> copyservice <WORD> connector <WORD>

Description: Configure copy node and connector

Syntax:

Command Mode: l4l7 graph : Configure L4-L7 Service Graph

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
(config-graph)# connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer service <WORD> connector <WORD> copyservice <WORD> connector <WORD>

connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer terminal provider|consumer copyservice <WORD> connector <WORD>

Description: Configure copy node and connector

Syntax:

Command Mode: l4l7 graph : Configure L4-L7 Service Graph

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
(config-graph)# connection <WORD> [peerconnect <Peer connectivity>] terminal provider|consumer terminal provider|consumer copyservice <WORD> connector <WORD>

connector <WORD> [cluster-interface <WORD>]

Description: Configure Connector for a Service Node

Syntax:

Command Mode: service : Configure L4-L7 Service

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# l4l7 graph <WORD> [contract <contract-option>]
(config-graph)# service <WORD> [device-cluster-tenant <WORD>] [device-cluster <WORD>] [mode <Available Modes>] [svcredir <Service Redirection>] [service-type <Service Type>]
(config-service)# connector <WORD> [cluster-interface <WORD>]

console [severity severity <severity-value>] [format <format>]

Description: Enable the logging to console(switches only)

Syntax:

Command Mode: logging : Logging server group configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# logging server-group <WORD>
(config-logging)# console [severity severity <severity-value>] [format <format>]

consumer epg-label <WORD>

Description: Add a consumer EPG label

Syntax:

Command Mode: external-l3 epg : External L3 EPG configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
(config-tenant-l3ext-epg)# consumer epg-label <WORD>

consumption <consumption>

Description: Update consumption value in PoE Node-policy

Syntax:

Command Mode: template power-over-ethernet node-policy : Configure Power Over Ethernet Parameters

Command Path:

# configure [['terminal', 't']]
(config)# template power-over-ethernet node-policy <WORD>
(config-poe-node-pol)# consumption <consumption>

consumption <4000-30000>

Description: Set power wattage for interface consumption

Syntax:

Command Mode: switchport power-over-ethernet : Power Over Ethernet configuration

Command Path:

# configure [['terminal', 't']]
(config)# template policy-group <WORD>
(config-pol-grp-if)# switchport power-over-ethernet <WORD>
(config-power-over-ethernet)# consumption <4000-30000>

contract-id <WORD>

Description: Service contract id of the customer

Syntax:

Command Mode: destination-profile : Configure destination profile Parameters

Command Path:

# configure [['terminal', 't']]
(config)# callhome common
(config-callhome)# destination-profile
(config-callhome-destnprof)# contract-id <WORD>

contract-id <WORD>

Description: Service contract id of the customer

Syntax:

Command Mode: destination-profile : Configure destination profile Parameters

Command Path:

# configure [['terminal', 't']]
(config)# smartcallhome common
(config-smartcallhome)# destination-profile
(config-callhome-destnprof)# contract-id <WORD>

contract <WORD> [type <type>]

Description: Configure binary contracts between Application EPGs

Syntax:

Command Mode: tenant : Tenant configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# contract <WORD> [type <type>]

contract consumer <WORD> [qos-class <WORD>]

Description: Add the supplied contract to be consumed by any AEPg on this VRF

Syntax:

Command Mode: vrf : Configuration for vrf

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# vrf context <WORD>
(config-tenant-vrf)# contract consumer <WORD> [qos-class <WORD>]

contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]

Description: Add a contract consumed by this AEPg, along with an optional list of subject labels

Syntax:

Command Mode: epg : AEPg configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# application <WORD>
(config-tenant-app)# epg <WORD> [type <WORD>]
(config-tenant-app-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]

contract consumer <contractName> [imported] [label <WORD>]

Description: Add a contract consumed by this EPG, along with an optional list of subject labels

Syntax:

Command Mode: external-l3 epg : External L3 EPG configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
(config-tenant-l3ext-epg)# contract consumer <contractName> [imported] [label <WORD>]

contract consumer <WORD> [imported] [label <WORD>]

Description: Add a contract consumed by this In-band Epg, along with an optional list of subject labels

Syntax:

Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties or create new inband

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# inband-mgmt epg <WORD>
(config-inb-epg)# contract consumer <WORD> [imported] [label <WORD>]

contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]

Description: Add a contract consumed by this EPG, along with an optional list of subject labels

Syntax:

Command Mode: external-l2 : L2 external EPG creation/configuration

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# external-l2 epg <WORD>
(config-tenant-l2ext-epg)# contract consumer <WORD> [imported] [label <WORD>] [qos-class <WORD>]

contract consumer <WORD> [imported]

Description: Add a consumer contract

Syntax:

Command Mode: match prefix-list : Match entries of a prefix-list

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
(config-leaf-vrf)# route-map <WORD>
(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
(config-leaf-vrf-route-map-match)# contract consumer <WORD> [imported]

contract consumer <WORD> [imported]

Description: Add a consumer contract

Syntax:

Command Mode: match prefix-list : Match entries of a prefix-list

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
(config-leaf-vrf)# route-map <WORD>
(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
(config-leaf-vrf-route-map-match)# contract consumer <WORD> [imported]

contract deny <WORD>

Description: Attach a taboo contract to this AEPg

Syntax:

Command Mode: epg : AEPg configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# application <WORD>
(config-tenant-app)# epg <WORD> [type <WORD>]
(config-tenant-app-epg)# contract deny <WORD>

contract deny <contractName>

Description: Attach a taboo contract to this EPG

Syntax:

Command Mode: external-l3 epg : External L3 EPG configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
(config-tenant-l3ext-epg)# contract deny <contractName>

contract deny <contractName>

Description: Attach a taboo contract to this InBand Epg

Syntax:

Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties or create new inband

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# inband-mgmt epg <WORD>
(config-inb-epg)# contract deny <contractName>

contract deny <WORD>

Description: Attach a taboo contract to this EPG

Syntax:

Command Mode: external-l2 : L2 external EPG creation/configuration

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# external-l2 epg <WORD>
(config-tenant-l2ext-epg)# contract deny <WORD>

contract enforce [ingress] [egress]

Description: Add a policy enforcement

Syntax:

Command Mode: vrf : Configuration for vrf

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# vrf context <WORD>
(config-tenant-vrf)# contract enforce [ingress] [egress]

contract intra-epg <WORD>

Description: Contract for controlling Intra-EPG traffic

Syntax:

Command Mode: epg : AEPg configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# application <WORD>
(config-tenant-app)# epg <WORD> [type <WORD>]
(config-tenant-app-epg)# contract intra-epg <WORD>

contract provider <WORD> [qos-class <WORD>]

Description: Add the supplied contract to be provided by any AEPg on this VRF

Syntax:

Command Mode: vrf : Configuration for vrf

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# vrf context <WORD>
(config-tenant-vrf)# contract provider <WORD> [qos-class <WORD>]

contract provider <WORD> [label <WORD>] [qos-class <WORD>]

Description: Contract provided by this AEPg, along with an optional list of subject labels

Syntax:

Command Mode: epg : AEPg configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# application <WORD>
(config-tenant-app)# epg <WORD> [type <WORD>]
(config-tenant-app-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]

contract provider <contractName> [label <WORD>]

Description: Add a contract provided by this EPG, along with an optional list of subject labels

Syntax:

Command Mode: external-l3 epg : External L3 EPG configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# external-l3 epg <WORD> [oob-mgmt] [l3out <l3out>]
(config-tenant-l3ext-epg)# contract provider <contractName> [label <WORD>]

contract provider <contractName> [label <label>]

Description: Add a contract provided by this AEPg, along with an optional list of subject labels

Syntax:

Command Mode: inband-mgmt : Enter Inside In-band management mode to modify inband properties or create new inband

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# inband-mgmt epg <WORD>
(config-inb-epg)# contract provider <contractName> [label <label>]

contract provider <WORD> [label <WORD>] [qos-class <WORD>]

Description: Add a contract provided by this EPG, along with an optional list of subject labels

Syntax:

Command Mode: external-l2 : L2 external EPG creation/configuration

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# external-l2 epg <WORD>
(config-tenant-l2ext-epg)# contract provider <WORD> [label <WORD>] [qos-class <WORD>]

contract provider <contractName>

Description: Add a contract provided by this AEPg, along with an optional list of subject labels

Syntax:

Command Mode: oob-mgmt : Creates/Modify the out of band mgmt under the tenant mgmt

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# oob-mgmt epg <epgval>
(config-oob-epg)# contract provider <contractName>

contract provider <WORD>

Description: Add a provider contract

Syntax:

Command Mode: match prefix-list : Match entries of a prefix-list

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
(config-leaf-vrf)# route-map <WORD>
(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
(config-leaf-vrf-route-map-match)# contract provider <WORD>

contract provider <WORD>

Description: Add a provider contract

Syntax:

Command Mode: match prefix-list : Match entries of a prefix-list

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# vrf context tenant <WORD> vrf <WORD> [l3out <l3out>]
(config-leaf-vrf)# route-map <WORD>
(config-leaf-vrf-route-map)# match prefix-list <WORD> [deny]
(config-leaf-vrf-route-map-match)# contract provider <WORD>

control-plane-policing-prefilter <arg>

Description: Add leaf ACL policy

Syntax:

Command Mode: template leaf-policy-group : Configure Leaf Policy Group

Command Path:

# configure [['terminal', 't']]
(config)# template leaf-policy-group <WORD>
(config-leaf-policy-group)# control-plane-policing-prefilter <>

control-plane-policing-prefilter <arg>

Description: Add spine ACL policy

Syntax:

Command Mode: template spine-policy-group : Configure Spine Policy Group

Command Path:

# configure [['terminal', 't']]
(config)# template spine-policy-group <WORD>
(config-spine-policy-group)# control-plane-policing-prefilter <>

controller-group

Description: Controller Upgrade Configuration Mode

Command Mode: firmware : Firmware upgrade configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# firmware
(config-firmware)# controller-group

controller

Description: Configure Controller Node

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# controller

coop-fabric

Description: Council Of Oracles Protocol (COOP)

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# coop-fabric

coop fabric

Description: COOP protocol

Syntax:

Command Mode: pod : Pod configuration mode

Command Path:

# configure [['terminal', 't']]
(config)# pod <NUMBER>
(config-pod)# coop fabric

copp-aggr <arg>

Description: Add CoPP aggregate policy

Syntax:

Command Mode: template leaf-policy-group : Configure Leaf Policy Group

Command Path:

# configure [['terminal', 't']]
(config)# template leaf-policy-group <WORD>
(config-leaf-policy-group)# copp-aggr <>

copp-aggr <arg>

Description: Add CoPP aggregate policy

Syntax:

Command Mode: template spine-policy-group : Configure Spine Policy Group

Command Path:

# configure [['terminal', 't']]
(config)# template spine-policy-group <WORD>
(config-spine-policy-group)# copp-aggr <>

cos enable

Description: Enable Cos Marking

Command Mode: vmware-domain : Associate EPG to a VMWare Domain

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# application <WORD>
(config-tenant-app)# epg <WORD> [type <WORD>]
(config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>] [allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [binding-type staticBinding|dynamicBinding|ephemeral] [port-allocation fixed|elastic] [num-ports <WORD>] [delimiter <WORD>]
(config-tenant-app-epg-domain)# cos enable

cos value <num>

Description: CoS value <0-7>

Syntax:

Command Mode: vmware-domain : Associate EPG to a VMWare Domain

Command Path:

# configure [['terminal', 't']]
(config)# tenant <WORD>
(config-tenant)# application <WORD>
(config-tenant-app)# epg <WORD> [type <WORD>]
(config-tenant-app-epg)# vmware-domain member <WORD> [encap <WORD>] [primary-encap <WORD>] [allow-micro-segmentation] [deploy <WORD>] [push <WORD>] [binding-type staticBinding|dynamicBinding|ephemeral] [port-allocation fixed|elastic] [num-ports <WORD>] [delimiter <WORD>]
(config-tenant-app-epg-domain)# cos value <num>

cost <NUMBER>

Description: Set OSPF cost for the interface

Syntax:

Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates

Command Path:

# configure [['terminal', 't']]
(config)# leaf <101-4000>
(config-leaf)# template ospf interface-policy <WORD> tenant <WORD>
(config-interface-policy)# cost <NUMBER>

cost <NUMBER>

Description: Set OSPF cost for the interface

Syntax:

Command Mode: template ospf interface-policy : Configure OSPF Interface Policy Templates

Command Path:

# configure [['terminal', 't']]
(config)# spine <101-4000>
(config-spine)# template ospf interface-policy <WORD> tenant <WORD>
(config-interface-policy)# cost <NUMBER>

country <WORD>

Description: Set The two-letter ISO code for the country where the organization is located.

Syntax:

Command Mode: csr : A csr mode to create and hold an SSL certificate

Command Path:

# configure [['terminal', 't']]
(config)# crypto keyring <WORD>
(config-keyring)# csr
(config-csr)# country <WORD>

crypto aes

Description: AES encryption configuration

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# crypto aes

crypto ca <WORD>

Description: Configure certificate authority related information

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# crypto ca <WORD>

crypto keyring <WORD>

Description: A keyring mode to create and hold an SSL certificate

Syntax:

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# crypto keyring <WORD>

crypto webtoken

Description: The cryptographic data used for generating and verifying web tokens.

Command Mode: configure : Configuration Mode

Command Path:

# configure [['terminal', 't']]
(config)# crypto webtoken

csr

Description: A csr mode to create and hold an SSL certificate

Command Mode: crypto keyring : A keyring mode to create and hold an SSL certificate

Command Path:

# configure [['terminal', 't']]
(config)# crypto keyring <WORD>
(config-keyring)# csr

customer-id <WORD>

Description: The customer id

Syntax:

Command Mode: destination-profile : Configure destination profile Parameters

Command Path:

# configure [['terminal', 't']]
(config)# callhome common
(config-callhome)# destination-profile
(config-callhome-destnprof)# customer-id <WORD>

customer-id <WORD>

Description: The customer id

Syntax:

Command Mode: destination-profile : Configure destination profile Parameters

Command Path:

# configure [['terminal', 't']]
(config)# smartcallhome common
(config-smartcallhome)# destination-profile
(config-callhome-destnprof)# customer-id <WORD>