Full Cisco Trademarks with Software License
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)
Cisco 4000 Series Integrated Services Routers Overview
 Note |
Cisco IOS XE 17.15.1a is the first release for Cisco 4000 Series Integrated Services Routers in the Cisco IOS XE 17.15.x release series. |
Note |
See the End-of-Sale and End-of-Life Announcement for the Cisco ISR4200, ISR4300 and select ISR4400 Series Platform page for information about the end-of-life milestones for the Cisco 4000 Series Integrated Service Routers. |
Note |
See the End-of-Sale and End-of-Life Announcement for the Cisco ISR4461 Series Platform page for information about the end-of-life milestones for the Cisco ISR4461 series platform. |
The Cisco 4000 Series ISRs are modular routers with LAN and WAN connections that can be configured by means of interface modules, including Cisco Enhanced Service Modules (SM-Xs), and Network Interface Modules (NIMs).
Note |
Starting with Cisco IOS XE Amsterdam 17.3.2 release, with the introduction of Smart Licensing Using Policy, even if you configure a hostname for a product instance or device, only the Unique Device Identifier (UDI) is displayed. This change in the display can be observed in all licensing utilities and user interfaces where the hostname was displayed in earlier releases. It does not affect any licensing functionality. There is no workaround for this limitation. The licensing utilities and user interfaces that are affected by this limitation include only the following:
|
Product Field Notice
Cisco publishes Field Notices to notify customers and partners about significant issues in Cisco products that typically require an upgrade, workaround or other user action. For more information, see https://www.cisco.com/c/en/us/support/web/field-notice-overview.html.
We recommend that you review the field notices to determine whether your software or hardware platforms are affected. You can access the field notices from https://www.cisco.com/c/en/us/support/web/tsd-products-field-notice-summary.html#%7Etab-product-categories.
System Requirements
The following are the minimum system requirements:
Note |
There is no change in the system requirements from the earlier releases. |
-
Memory: 4 GB DDR3 up to 32 GB
-
Hard Drive: 200 GB or higher (Optional). The hard drive is only required for running services such as Cisco ISR-WAAS.
-
Flash Storage: 4 GB to 32 GB
-
NIMs and SM-Xs: Modules (Optional)
-
NIM SSD (Optional)
For more information, see the Cisco 4000 Series ISRs Data Sheet.
Note |
For more information on the Cisco WAAS IOS-XE interoperability, see the WAAS Release Notes: https://www.cisco.com/c/en/us/support/routers/wide-area-application-services-waas-software/products-release-notes-list.html. |
Determining the Software Version
You can use the following commands to verify your software version:
-
For a consolidated package, use the show version command
-
For individual sub-packages, use the show version installed command
Upgrading to a New Software Release
To install or upgrade, obtain a Cisco IOS XE 17.15.x consolidated package (image) from Cisco.com. You can find software images at http://software.cisco.com/download/navigator.html. To run the router using individual sub-packages, you also must first download the consolidated package and extract the individual sub-packages from a consolidated package.
Note |
When you upgrade from one Cisco IOS XE release to another, you may see %Invalid IPV6 address error in the console log file. To rectify this error, enter global configuration mode, and re-enter the missing IPv6 alias commands and save the configuration. The commands will be persistent on subsequent reloads. |
For more information on upgrading the software, see the Installing the Software section of the Software Configuration Guide for the Cisco 4000 Series ISRs.
Recommended Firmware Versions
The following table lists the recommended ROMMON and CPLD versions for Cisco IOS XE 17.2.x onwards releases.
|
Cisco 4000 Series ISRs |
Existing ROMMON |
Cisco Field-Programmable Devices |
CCO URL for the CPLD Image |
|---|---|---|---|
|
Cisco 4461 ISR |
16.12(2r) |
21102941 |
|
|
Cisco 4451-X ISR |
16.12(2r) |
19042950 |
|
|
Cisco 4431 ISR |
16.12(2r) |
19042950 |
|
|
Cisco 4351 ISR |
16.12(2r) |
19040541 |
|
|
Cisco 4331 ISR |
16.12(2r) |
19040541 |
|
|
Cisco 4321 ISR |
16.12(2r) |
19040541 |
|
|
Cisco 4221 ISR |
16.12(2r) |
19042420 |
For more information about the minimum and recommended ROMMON versions, see the Upgrading Field-Programmable Hardware Devices for Cisco 4000 Series ISRs
Note |
Upgrading Field-Programmable Hardware Devices
The hardware-programmable firmware is upgraded when Cisco 4000 Series ISR contains an incompatible version of the hardware-programmable firmware. To do this upgrade, a hardware-programmable firmware package is released to customers.
Generally, an upgrade is necessary only when a system message indicates one of the field-programmable devices on the Cisco 4000 Series ISR needs an upgrade, or a Cisco technical support representative suggests an upgrade.
From Cisco IOS XE Release 3.10S onwards, you must upgrade the CPLD firmware to support the incompatible versions of the firmware on the Cisco 4000 Series ISR. For upgrade procedures, see the Upgrading Field-Programmable Hardware Devices for Cisco 4000 Series ISRs.
Feature Navigator
You can use Cisco Feature Navigator to find information about feature, platform, and software image support. To access Cisco Feature Navigator, go to https://cfnng.cisco.com/. An account on cisco.com is not required.
New and Changed Information
New and Changed Software Features in Cisco IOS XE 17.15.4
There are no new features for this release.
New and Changed Software Features in Cisco IOS XE 17.15.3a
There are no new features for this release.
New and Changed Software Features in Cisco IOS XE 17.15.2a
There are no new features for this release.
New and Changed Software Features in Cisco IOS XE 17.15.1a
|
Feature |
Description |
|
|---|---|---|
|
The File Transfer using HTTP or HTTPs feature allows you to copy files from a remote server to your local device, using the copy command. From Cisco IOS XE 17.15.1a, you must provide the absolute file path when you execute the copy command, to transfer the file. |
||
|
From Cisco IOS XE 17.15.1a, this feature provides the ability to define and configure a new single Cisco Umbrella credential for both Umbrella SIG and Umbrella DNS. |
||
|
Enabling Flow Level Flexible NetFlow Support for SD-Routing Devices |
The Flow-level Flexible NetFlow (FNF) feature allows you to monitor the NetFlow traffic and view all the flow-level FNF data that is captured including application-level statistics. This feature is only supported on ISR4461. |
|
|
From Cisco IOS XE 17.15.1a, the Enhanced NAT Management feature enables network operators to safeguard system performance by limiting NAT translations based on CPU usage with the ip nat translation max-entries cpu command. This feature also enables streamlining NAT synchronization in redundant systems using the ip nat settings redundancy optimized-data-sync command. |
||
|
Configure Multiple WAN Interfaces on Cisco SD-Routing Devices Using a Custom VRF |
You can now create a custom VRF that hosts one or more WAN interfaces. You can extend this functionality to create multiple custom VRFs with each VRF hosting multiple WAN interfaces. These WAN interfaces now function as transport interfaces to establish control connections to the Cisco Catalyst SD-WAN Manager. Having multiple WAN interfaces ensures that there is resiliency in control connections and routing of transport traffic. |
|
|
From Cisco IOS XE 17.15.1a, network administrators can monitor SD-Routing device alarms on Cisco Catalyst SD-WAN Manager. This feature enables SD-Routing devices to record and store various alarms generated by control components and routers. For more information, see Cisco SD-Routing Command Reference Guide. |
||
|
Network-Wide Path Insights (NWPI) is a tool that allows network administrators to monitor Cisco SD-Routing deployment, identify network and application issues, and optimize the network. |
||
|
This release introduces license management support for SD-Routing devices. The supported licensing workflows include license assignment or configuration, license use, and license usage reporting. Depending on the device, these workflows are performed in the Cisco Catalyst SD-WAN Manager or on the device. |
||
|
This feature explains how to seamlessly upgrade and onboard an existing Cisco Routing device into the Cisco SD-WAN infrastructure. |
||
Configure the Router for Web User Interface
This section explains how to configure the router to access Web User Interface. Web User Interface requires the following basic configuration to connect to the router and manage it.
-
An HTTP or HTTPs server must be enabled with local authentication.
-
A local user account with privilege level 15 and accompanying password must be configured.
-
Vty line with protocol SSH/Telnet must be enabled with local authentication. This is needed for interactive commands.
-
For more information on how to configure the router for Web User Interface, see Cisco 4000 Series ISRs Software Configuration Guide, Cisco IOS XE 17.
Resolved and Open Bugs
This section provides information about the bugs in Cisco 4000 Series Integrated Services Routers and describe unexpected behavior. Severity 1 bugs are the most serious bugs. Severity 2 bugs are less serious. Severity 3 bugs are moderate bugs. This section includes severity 1, severity 2, and selected severity 3 bugs.
The open and resolved bugs for this release are accessible through the Cisco Bug Search Tool. This web-based tool provides you with access to the Cisco bug tracking system, which maintains information about bugs and vulnerabilities in this product and other Cisco hardware and software products. Within the Cisco Bug Search Tool, each bug is given a unique identifier (ID) with a pattern of CSCxxNNNNN, where x is any letter (a-z) and N is any number (0-9). The bug IDs are frequently referenced in Cisco documentation, such as Security Advisories, Field Notices and other Cisco support documents. Technical Assistance Center (TAC) engineers or other Cisco staff can also provide you with the ID for a specific bug. The Cisco Bug Search Tool enables you to filter the bugs so that you only see those in which you are interested.
In addition to being able to search for a specific bug ID, or for all bugs in a product and release, you can filter the open and/or resolved bugs by one or more of the following criteria:
-
Last modified date
-
Status, such as fixed (resolved) or open
-
Severity
-
Support cases
You can save searches that you perform frequently. You can also bookmark the URL for a search and email the URL for those search results.
Note |
If the bug that you have requested cannot be displayed, this may be due to one or more of the following reasons: the bug ID does not exist, the bug does not have a customer-visible description yet, or the bug has been marked Cisco Confidential. |
Resolved and Open Bugs in Cisco 4000 Series Integrated Services Routers
Resolved Bugs - Cisco IOS XE 17.15.4
|
Identifier |
Headline |
|---|---|
|
The device crashes when processing SIP traffic. A crash was observed on the CUBE while handling a DO INVITE. |
|
|
Multiple inside local addreses are translated to same inside global IP address and port. |
|
|
Segmentation fault on the sessmgrd process. |
|
|
Unexpected reload with segmentation fault due to Open DNS Dev-Reg process. |
|
|
QFP crash with stuck threads while attempting to lock cft policy under Autonomous mode. |
|
|
IPsec-related crash on an IOS-XE device. |
|
|
Large number of BFD sessions stuck due to out of window drops reported with control connections NAT flaps. |
|
|
cpp-mcplo-ucode crashes in the device running IOS-XE. |
|
|
VG450 crashes with PKI revocation-check ocsp none enabled. |
|
|
Traffic with TTL 2 is punted to CPU when CEF holds MPLS labels set to none. |
|
|
The device underwent a reload due to a critical process failure: the cpp_ha_top_level_server process encountered a fault on forwarding processor 0/0 (fp_0_0) with return code 69. |
|
|
YANG: Unable to deploy aaa accounting network command. |
|
|
IKEv2 fails to parse certain route-set prefix Cisco VSA attributes from RADIUS server. |
|
|
The device rebooted after modifying the telemetry subscription update policy from "periodic" to "on-change. |
|
|
The router experiences a failure when a service policy is applied to a port-channel interface that is configured as a tunnel source. |
|
|
Serial interface configuration lost after reload. |
|
|
In a FlexVPN deployment, the IP address assigned to the spoke interface unexpectedly changes to unassigned. |
|
|
Fragmented UDP SIP packets dropped on PE with IpFragErr on IP VFR and MPLS enabled tunnel interface. |
|
|
EVPN Multi-Homing: Administratively Shutdown Ports Are Re-Enabled After Core Isolation Recovery (WAN link recovered). |
|
|
KMI messages introducing a crash while enabling debug. |
|
|
Memory leak in CCSIP_SPI_CONTROL and Dead processes. |
|
|
Memory leak on Chunk Manager via DBAL EVENTS process. |
|
|
The device intermittently runs out of CGM (Class-Group Manager) memory when operating with a scaled Zone-Based Firewall (ZBFW) policy. |
|
|
Cisco cEdge devices failed due to a critical process failure: the vip_confd_startup_sh process encountered a fault on route processor 0/0 (rp_0_0) with return code 6. |
|
|
Failing to ping to service-side IPv4 interface from remote cEdge with IPv6 tunnel and LTE Cellular. |
|
|
Router Tracebacks observed in voip trace flow. |
|
|
Crash making calls during codec negotiation. |
|
|
Segfault in CCSIP_SPI_CONTROL During CALL_LOOP and TLS_SOCKET_SEND_BLOCKED Events |
|
|
SGW sends AOR id value in RPID/PAI header. |
|
|
ID manager runs out of IDs, memory leak when using CTS. |
|
|
CUBE is not responding with 200 OK for REINVITE from ISP causing the transfer call getting affected. |
|
|
PPP sessions are not establishing when using L2TP over IPsec. |
|
|
A configuration parser issue occurs when NAT is configured with both the reversible and redundancy options enabled |
|
|
Crash when clearing L2TP tunnels with the command clear vpdn tunnel l2tp <ID> |
|
|
cEdge device crashes when running a NWPI trace initiated from vManage. |
|
|
PKI Trustpoint password command only allows encryption type 0 and 7 on all IOS XE platforms. |
|
|
Tunnels are dropped when Call Admission Control (CAC) is configured for Virtual Dynamic Private Network (VDPN) and the CPU exceeds the threshold as a result of an SSH request for the show tech command. |
|
|
Enable strict key exchange (strict-kex) support in IOS-SSH to mitigate CVE-2023-48795, also known as the Terrapin Attack. |
|
|
Facing space issue on the flash during upgrade using Cisco Catalyst Center. |
|
|
Random failure observed after tcp confguration changes. |
|
|
On IOS-XE devices, a memory leak is observed during IPsec/IKE session establishment when certificate-based authentication is used. |
|
|
GET VPN Mismatch in GMs reported across COOP Cooperative Key Server (COOP) due to a Key Encryption Key (KEK) synchronization issue between the primary and secondary key servers. |
|
|
Tunnel interfaces flap unexpectedly—undergoing unplanned delete and create cycles in PWK scenarios when there are changes to private control NAT configurations. |
|
|
On the Cisco router, certificate-based MACsec experiences flapping when 802.1X reauthentication timers are configured and the device is reloaded. |
|
|
A failure occurs during a hairpin call on the device. |
|
|
Configuring logging discriminator name longer than 8 characters reloads standby switch. |
|
|
On Cisco devices, enabling the macsec disable-sci command results in network traffic being halted. |
|
|
AAA settings not working based on template associated with the domain-name. |
|
|
IPSec umbrella tunnels are going down everytime umbrella side executes the rekey. |
|
|
On Cisco devices, the confd_cli process exhibits high CPU utilization after executing the command show zbfw-dp sessions | tab. |
Open Bugs - Cisco IOS XE 17.15.4
All open bugs for this release are available in the Cisco Bug Search Tool.
|
Identifier |
Headline |
|---|---|
|
Device experienced unexpected reload due to debug daemon (dbgd) process. |
|
|
Next Hop Resolution Protocol (NHRP) Encap Error for Purge Request appears on spoke despite correct routing at the hub. |
|
|
Simple Network Management Protocol walk (SNMPwalk) fails to consistently return tunnel names due to incomplete tunnel setup. |
Resolved Bugs - Cisco IOS XE 17.15.3a
|
Identifier |
Headline |
|---|---|
|
Large number of BFD sessions stuck with out of window drops. |
|
|
BFD session is down after change tloc preference with pairwise-keying enabled. |
|
|
Unexpected reload due to application redundancy configuration. |
|
|
Pairwise-keying every single bfd session up/down which trigger tunnel delete/create events. |
|
|
Unexpected reload in NHRP, cache freed prior to function call. |
|
|
Startup config lost for interfaces NIM-(1|2)GE-CU-SFP. |
|
|
Unexpected reload on device due to performance monitor with packet service insertion from spoke. |
|
|
Device may experience a "qfp-ucode" crash due to stuck thread condition. |
|
|
Device crashed due to critical process vip_confd_startup_sh fault on rp_0_0 (rc=6). |
|
|
Administrative distance of IPv6 static route to cellular interface overwrite with 254. |
|
|
OMP is redistributing summary routes in the service VPN even though the exact networks don't exist. |
|
|
Incoming packet are drop with bad checksum when l2tp through ipsec encrypted tunnel on device. |
|
|
cpp_cp_svr crash noticed when configured service-policy to a dialer interface. |
|
|
After change integrity-type twice, all bfd sessions will be down. |
|
|
CPP crashes after routing table changes. |
|
|
Failed to load cert chain for trustpoint. |
|
|
GETVPN Mismatch in GMs reported across COOP Due to KEK Sync Issue Between Prim & Sec KSs. |
|
|
UTD snort crash at memif_shm_peek_first_packet (handle=0x0). |
|
|
FLOWDB_OOM condition can lead to packet loss with GRE non-IPSEC tunnel. |
|
|
Cflowd source interface for sub-interface does not get pushed to cedge. |
|
|
Router unexpected reload with ipv4_sbc_input () at /dplane/feature/sbc/sbc_packet decode. |
|
|
Router crash during SGW sync in VOICE REG BG Process. |
|
|
Listen-port command is not working properly under tenants for UDP. |
|
|
CDR file accounting credentials exposure. |
|
|
Router cube sip-ua commands lost after reload. |
|
|
Memory leak on CUBE in subscribe pass-thru scenario. |
|
|
CDR file accounting creates dummy files. |
|
|
OOD Subscribe with event message-summary is causing memory leak on CUBE. |
|
|
CUBE incorrectly offers rtp instead of srtp in 200OK for srtp fallback scenario. |
Open Bugs - Cisco IOS XE 17.15.3a
All open bugs for this release are available in the Cisco Bug Search Tool.
|
Identifier |
Headline |
|---|---|
|
Missing Calling-Station-ID in radius messages. |
|
|
PPP is not establishing when l2tp over ipsec. |
|
|
Memory Leak observed in IPSEC/IKE session bringup with cert-based authentication. |
|
|
Router crash due to failed DLC license conversion when contacting CSSM. |
|
|
DSL SFP: VDSL/ADSL lines are flapping in Customer site. |
|
|
KMI messages introducing a crash while enabling debug. |
|
|
Tx/Rx optical power values diffrent for "show int" and "show hw-module". |
|
|
Crash when clearing L2TP tunnels with the command "clear vpdn tunnel l2tp <ID>". |
|
|
Failing to ping to service-side IPv4 interface from remote cEdge with IPv6 tunnel and LTE Cellular. |
|
|
FlexVPN - IP address assigned to spoke changes to unassigned. |
|
|
BFD sessions stuck in down state due to SA_NOT_FOUND. |
Resolved Bugs - Cisco IOS XE 17.15.2a
|
Identifier |
Headline |
|---|---|
|
DSP occasionally crashes when pcm capture is enabled. |
|
|
Crash occurs when IPv6 packets with link-local source are forwarded to SDWAN tunnels. |
|
|
Procyon synchronize DTL does not wait until complete due to compiler optimization. |
|
|
DSMP layer is unable to close EDSP channels if a call is disconnected before connect. |
|
|
CPP unexpectedly reboot due to QFP CPP stuck at waiting for rw_lock - Lock id of 0 released. |
|
|
Cisco IOS-XE router can reboot unexpectedly while configuring NAT static translation. |
|
|
Process crash seen on SD-Routing TSN platform + Permission Denied errors. |
|
|
match traffic-category through vManage add-on CLI push failed. |
|
|
Startup configuration failure post PKI server enablement. |
|
|
MGCP GW fails to respond with 250 OK when there's a delay from dataplane in gathering statistics. |
|
|
High IRAM utilization at 99% in scaled flows. |
|
|
Cannot import device certificate. |
|
|
An IOS XE router running as a cEdge may experience an unexpected reset due to dbgd process. |
|
|
Process IOMd memory leak due to POE TDL message. |
|
|
SD-WAN ZBFW TCAM misprogramming after rules are reordered on device. |
|
|
SD-WAN ZBFW TCAM misprogramming after rules are reordered on device - CCE changes. |
|
|
Unexpected Reload Due to "cpp-mcplo-ucode" Process when handling fragments with SRv6 routing |
|
|
Memory leak in fman_rp under acl_db. |
|
|
IPv6 flowspec nexthop redirect policy not redirecting the traffic on IOS XE. |
|
|
Device crashes in IOSd due to Malformed DMVPN-5-NHRP_RES_REPLY_IGNORE Syslog. |
Open Bugs - Cisco IOS XE 17.15.2a
All open bugs for this release are available in the Cisco Bug Search Tool.
|
Identifier |
Headline |
|---|---|
|
Router crash due to failed DLC license conversion when contacting CSSM. |
|
|
Unexpected reload due to application redundancy configuration. |
|
|
Cannot configure MD5 for the hash under the IKEv2 proposal when compliance shield is disabled. |
|
|
Tracker group with IP and DNS name tracker elements goes down when DNS query is failing. |
|
|
Missing Calling-Station-ID in radius messages. |
|
|
Device crashes when EPC is configured on 100Gb link. |
|
|
Fragmented UDP SIP packets dropped on PE with IpFragErr on IP VFR and MPLS enabled tunnel interface. |
|
|
Device crash PKI: Failed to load cert chain for trustpoint. |
|
|
Device crashes with PKI revocation-check ocsp none enabled. |
|
|
Device removes NAT egress-interface option from cEdge config - NAT yang changes. |
|
|
IOSD chasfs task crashes when retrieving platform information. |
|
|
DMVPN Tunnel bounces for the second time after RP3 failover and recovery. |
|
|
DSL SFP: VDSL/ADSL lines are flapping in customer site. |
|
|
Unexpected reload Critical process linux_iosd_image fault on rp_0_0 (rc=139). |
|
|
PPP is not establishing when l2tp over IPsec. |
|
|
Unable to reach inband management IP on standby firewall HA device. |
|
|
peer reactive CLI for FlexVPN tunnel on IR1800 does not work. |
|
|
Device interface using DOD ip range. |
|
|
CCP craashed during UTD policy config application. |
|
|
FlexVPN - IP address assigned to spoke changes to unassigned. |
|
|
Unable to configure stream on cellular interface. |
|
|
Device removes NAT egress-interface option from cEdge config - CRYPTO yang changes. |
Resolved Bugs - Cisco IOS XE 17.15.1a
All resolved bugs for this release are available in the Cisco Bug Search Tool.
|
Bug ID |
Description |
|---|---|
|
CPP crashes after re-/configuring ip nat settings pap limit ... bpa feature in high QFP state. |
|
|
Crash due a segmentation fault due a negative value. |
|
|
%PMAN-0-PROCFAILCRIT: R0/0: pvp: A critical process vip_confd_startup_sh has failed (rc 6). |
|
|
EzPM application-performance profile cause memory leak and crash with long-lived idle TCP flows. |
|
|
Device repeatedly crashing in FTMd due to FNF flow add. |
|
|
Return traffic for outside to inside NAT traffic received on one TLOC is forwarded out of other TLOC. |
|
|
Config and dp show command do not match the dp oper output. |
|
|
SAIE application - no data to display for IOS XE router. |
|
|
Device crashed when issuing show sdwan ftm next-hop chain all. |
|
|
IOS XE Router: Unexpected reboot during PVDM OIR. |
|
|
FTMd crashes after receiving credentials feature template update. |
|
|
Coredump observed in tracker module while running cxp_sig_auto_tunnel suite. |
|
|
fman_fp memory meak on device. |
|
|
Unencrypted traffic due to non-functional IPsec tunnel in FLEXVPN hub & spoke setup. |
|
|
High CPU utilisation for confd_cli. |
|
|
BFD sessions flapping during IPSec rekey in scaled environment. |
|
|
sdn-network-infra-iwan failing to renew with "hash sha256" > 17.11. |
|
|
High memory utilization due to "ftmd" process. |
|
|
STCAPP command removed from VG410 after reload. |
|
|
After deleting a NAT configuration, the IP address still shows up in routing table. |
|
|
Device reloaded due to ezManage mobile app Service. |
|
|
GETVPN / migrating to new KEK RSA key does not trigger GM re-registration. |
|
|
FNF test_tunnel_name_change_CSCvt57024 case failed due to session of pm5 was not alive. |
|
|
Unable to build two IPSec SAs w/same source/destination where one peer is PAT'd through the other. |
|
|
ICMP tracker type (from echo to timestamp) change causes tracker to fail. |
|
|
Device unexpectedly reloads due to a crash in 'vdaemon' process. |
|
|
Dialer interface MAX MTU for PPPOA is 1492. |
|
|
appRouteStatisticsTable sequence misordered in CISCO-SDWAN-APP-ROUTE-MIB or OS returns wrong order. |
|
|
Router reloaded when generating admin tech while processing very high number of flows. |
|
|
Add FNF cache limit for show sdwan app-fwd flows. |
|
|
Device crashes while processing an NWPI trace. |
|
|
Unexpected reboot when a HTTP connection failed with 404 on a controller mode router. |
|
|
Chassis activate effective only after second re-try - with new uuid. |
|
|
DIA endpoint tracker not working with ECMP routes. |
Open Bugs - Cisco IOS XE 17.15.1a
All open bugs for this release are available in the Cisco Bug Search Tool.
|
Bug ID |
Description |
|---|---|
|
Custom Applications may not be programmed properly. |
|
|
Speed mismatch in IOS-XE configuration after device template push. |
|
|
match traffic-category add-on CLI push failed. |
|
|
Device crash due to DBGD process. |
|
|
File transfer fails "lost connection". |
|
|
Router rebooted unexpectedly due to process NHRP crash. |
|
|
Router can reboot unexpectedly while configuring NAT static translation. |
|
|
Multiple "match address local interface <int>" not pushed under crypto profile. |
|
|
Startup configuration failure post PKI server enablement. |
|
|
MKA session not coming up after shut/no shut with EVC. |
|
|
data-policy local-tloc-list breaks RTP media stream. |
|
|
ZBFW TCAM misprogramming after rules are reordered. |
|
|
Device denied for template push and some show commands with error application communication failure. |
|
|
GETVPN IPv6 crypto map not shown in interface configuration. |
|
|
Cannot import device certificate. |
|
|
Crash occurs when IPv6 packets with link-local source are forwarded. |
|
|
Device crashes in IOSd due to malformed DMVPN-5-NHRP_RES_REPLY_IGNORE syslog. |
|
|
Endpoint tracker does not fail if default route is removed. |
|
|
NAT DIA traffic getting dropped due to port allocation failure. |
|
|
Device unexpectedly reboot due to QFP CPP stuck at waiting for rw_lock - lock id of 0 released. |
|
|
RRI static not populating route after reload if stateful IPSec is configured. |
|
|
Device uses 3DES as default rekey algorithm for GETVPN. |
|
|
SPA.smu.bin drops when packet duplication link fails-over. |
|
|
Device showing custom APP as "unknown" for egress traffic when using DRE Opt. |
|
|
PPPoE session with sub-interface getting stuck after reboot. |
|
|
Centralized policy policer worked per PC on the same site not per site/vpn-list. |
|
|
System image file is not set to packages.conf when image expansion fails due to disk space. |
|
|
Packets not hitting the correct data policy after modifying the action of a sequence. |
Related Documentation
Communications, Services, and Additional Information
-
To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.
-
To get the business results you’re looking for with the technologies that matter, visit Cisco Services.
-
To submit a service request, visit Cisco Support.
-
To discover and browse secure, validated enterprise-class apps, products, solutions and services, visit Cisco DevNet.
-
To obtain general networking, training, and certification titles, visit Cisco Press.
-
To find warranty information for a specific product or product family, access Cisco Warranty Finder.
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software.
Documentation Feedback
To provide feedback about Cisco technical documentation, use the feedback form available in the right pane of every online document.
Troubleshooting
For the most up-to-date, detailed troubleshooting information, see the Cisco TAC website at https://www.cisco.com/en/US/support/index.html.
Go to Products by Category and choose your product from the list, or enter the name of your product. Look under Troubleshoot and Alerts to find information for the issue that you are experiencing.
Feedback