Product IDs

This appendix provides information about the product IDs for components of the Cisco CRS Carrier Routing System 8-Slot LCC. It contains the following tables:

These tables list the components that make up the routing system, their product IDs (the part numbers to use to order the components), and descriptions.


Note
For a complete list of line cards, route processors, SPAs and SIPs, and interface modules supported in the Cisco CRS 8-slot line card chassis, see Cisco CRS Data Sheets.

Chassis Component Product IDs

This table lists the product IDs for components in the Cisco CRS 8-slot LCC.

Table 1. 8-Slot Routing System Component Product IDs

Component

Product ID

Description

CRS 8-slot routing system

CRS-8/S

Cisco CRS 8-slot routing system

CRS 8-slot line card chassis

CRS-8-LCC(=)

Cisco CRS 8-slot line card chassis (spare chassis)

Fan tray

CRS-8-LCC-FAN-TR(=)

Cisco CRS 8-slot fan tray and fans (spare)(2 required for each chassis)

Air filter

CRS-8-LCC-FILTER(=)

Line card chassis filter pack (spare)

Inlet grille

CRS-8-FRNT-GRILL(=)CRS-8-PW-GRILL(=)

Line card chassis inlet air grille—fixed configuration powerLine card chassis inlet air grille—modular configuration power

Installation kit

CRS-8-INSTALL-KT(=)

Line card chassis installation kit(includes a set of horizontal shelf brackets, mounting screws, and other items)

Fixed Configuration Power Components

Power module filter

CRS-8-PWR-FILTER(=)

Filters (five per pack) for AC rectifier and DC PEM

AC Delta power components

AC Delta PDU

CRS-8-LCC-PDU-ACD(=)

Cisco CRS AC Delta power distribution unit(two required for each chassis)

AC rectifier module

CRS-8-AC-RECT(=)

Cisco CRS AC rectifier module(two required for each chassis, one for each PDU)

AC Wye power components

AC Wye PDU

CRS-8-LCC-PDU-ACW(=)

Cisco CRS AC Wye power distribution unit(two required for each chassis)

AC rectifier module

CRS-8-AC-RECT(=)

Cisco CRS AC rectifier module(two required for each chassis, one for each PDU)

DC power components

DC PDU

CRS-8-LCC-PDU-DC(=)

Cisco CRS DC power distribution unit(two required for each chassis)

DC PEM

CRS-8-DC-PEM(=)

Cisco CRS DC PEM1(two required for each chassis, one for each PDU)

Modular Configuration Power Components

AC power components, single-phase

AC power shelf

CRS-8-PSH-AC(=)

Cisco CRS single-phase AC power shelf(two required for each chassis)

AC PM

CRS-PM-AC(=)

Cisco CRS AC PM2(up to three required for each power shelf)

DC power components

DC power shelf

CRS-8-PSH-DC(=)

Cisco CRS DC power shelf (two required for each chassis)

DC PM

CRS-PM-DC(=)

Cisco CRS DC PM(up to four required for each power shelf)

Switch fabric cards

Switch fabric cards

CRS-8-FC/S(=)CRS-8-FC140/S(=)CRS-8-FC400/S (=) (200G mode)CRS-8-FC400/M (=) (200G mode)

Cisco CRS switch fabric card (half-height)(four required for each chassis)

Switch fabric blank

CRS-8-FC-BLANK(=)

Blank card carrier for each switch fabric slot (used during shipment, must be replaced by a switch fabric card)

Switch fabric handle

CRS-8-FC-HANDLE(=)

Handle for carrying card (spare)

Route processor card

Route processor (RP)3

CRS-8-RP(=)

Cisco CRS RP card(one required for each chassis; for redundant operation, you also need CRS-8-RP/R=)

Route processor, redundant

CRS-8-RP/R(=)

Optional route processor for redundant RP operation(one required for each chassis, along with CRS-8-RP=)

Route processor memory

CRS-MEM-2G(=)CRS-MEM-4G(=)

RP memory module, 2 gigabytesRP memory module, 4 gigabytes

Route processor blank

CRS-8-RP-BLANK(=)

Blank card carrier for each route processor slot(used during shipment, must be replaced by a route processor card)

Performance route processor (PRP)4

CRS-8-PRP-6G(=)

CRS-8-PRP-12G(=)

Cisco CRS performance route processor card

Route processor handle

CRS-8-RP-HANDLE(=)

Handle for carrying card (spare)

1 PEM = power entry module
2 PM = power module
3 RP = route processor
4 PRP = performance route processor

Optional MSC, FP, PLIM, SIP, and SPA Product IDs

Tables below list the product IDs for the modular services cards (MSCs) and physical layer interface modules (PLIMs) available for the Cisco CRS-1 8-slot LCC.

Table 2. MSC Component Product IDs

Component

Product ID

Description

MSC5

CRS-MSC-B(=),CRS-MSC-140G(=)CRS-MSC-X (200G)CRS-MSC-X-L (200G

Cisco CRS Layer 3 modular service card (every MSC must have an associated PLIM)

FP card

CRS-FP40CRS-FP140CRS-FP-X (200G)CRS-FP-X-L (200G)

Cisco CRS Layer 3 forwarding processor(every FP must have an associated PLIM)

LSP

CRS-LSP

Cisco CRS Series Label Switch Processor 140Gbps

MSC impedance carrier

CRS-MSC-IMPEDANCE(=)

Blank card carrier for each empty MSC slot (required for EMI compliance and cooling)

5 Refer to the product data sheet for ordering details.
Table 3. PLIM Component Product IDs

Component

Product ID

Description

1xOC-768 PLIM

1OC768-POS-SR(=)

1-port OC-768c/STM-256c PLIM, with short-reach optics (POS)

4xOC-192 PLIM

4OC192-POS/DPT-LR(=)

4-port OC-192c/STM-64c PLIM, with long-reach optics (POS or DPT)

4OC192-POS/DPT-IR(=)

4-port OC-192c/STM-64c PLIM, with intermediate-reach optics (POS or DPT)

4OC192-POS/DPT-SR(=)

4-port OC-192c/STM-64c PLIM, withshort-reach optics (POS or DPT)

4OC192-POS/DPT-VS(=)

4-port OC-192c/STM-64c PLIM, with very-short-reach optics (POS or DPT)

16xOC-48 PLIM

16OC48-POS/DPT(=)

POM-OC48-LR2-LC-C(=)POM-OC48-SR-LC-C(=)

OC-48c/STM-16c PLIM, uses small form-factor pluggable (SFP) modules (POS or DPT)

The PLIM uses 1 to 16 single-mode, long- and short-reach optic modules (mixing allowed):

  • Long-reach optics (POM-OC48-LR2-LC-C=)
  • Short-reach optics (POM-OC48-SR-LC-C=)

8x10-GE XENPAK PLIM

8-10GBE(=)

CRS-XENPAK10GB-LR(=)

10-GE PLIM, uses XENPAK optic modules.

The PLIM uses 1 to 8 single-mode, long-reachoptic modules:

Long-reach optics (CRS-XENPAK10GB-LR=)

8x10-GE and 4x10-GE XFP PLIMs

8-10GBE-WL-XFP(=)4-10GBE-WL-XFP(=)

10-GE PLIM, uses XFP optic modules.

These PLIMs use 1 to 8 (or 1 to 4) single-mode, XFP optic modules.

20x10-GE and 14x10-GE XFP PLIMs

20X10GBE-WL-XFP14X10GBE-WL-XFP

10-GE PLIM, uses XFP optic modules.

These PLIMs use 1 to 20 (or 1 to 14) single-mode, XFP optic modules.

1x100-GE CFP PLIM

1X100GBE(=)

100-GE PLIM, uses one CFP optic module.

PLIM impedance carrier

CRS-INT-IMPEDANCE(=)

Blank card carrier for each empty PLIM slot (required for EMI compliance and cooling)

Table 4. SIP and SPA Component Product IDs

Component

Product ID

Description

Cisco CRS SPA Interface Processor-800

CRS1-SIP-800

Occupies one PLIM slot on the Cisco CRS 16- and 8-Slot LCC. Supports six normal-height SPAs or three double-height SPAs or any combination in between.

1-Port OC-192c/ STM- 64 POS/RPR XFP SPA

SPA-OC192POS-XFP

—

4-Port OC-3c/STM-1 POS SPA

SPA-4XOC3-POS

—

8-Port OC-12c/STM-4 Multirate POS SPA

SPA-8XOC12-POS

—

8-Port Gigabit Ethernet SPA

SPA-8X1GE

—