The WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE is the newest addition to the roster of Wireless Access Points of Cisco. The WAP125 uses concurrent dual-band radio for improved coverage and user capacity. Gigabit Ethernet LAN interfaces with Power over Ethernet (PoE) facilitate flexible installation and reduce cabling and wiring costs.
To provide highly secure guest access to visitors and other users, WAP125 supports a captive portal with multiple authentication options and the ability to configure rights, roles, and bandwidth. Configure a cluster of WAPs for seamless roaming within a campus and manage them through a single IP address.
This article shows the product specifications of the WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE.
Note: To know more about the WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE, click here.
Specifications | Description |
---|---|
Cabling type | Category 5e or better |
Antennas | Internal antennas optimized for installation on a wall |
Operating System | Linux |
Specifications | Description |
---|---|
Ports | 1 - 10/100/1000 Ethernet, with support for 802.3at. PoE |
Buttons | Reset button |
LEDs | One multi-function LED |
Mounting and Physical Security | |
Multiple Mounting Options | Mounting bracket included for easy ceiling or wall mounting |
Physical Specifications | |
Physical dimensions (W x D x H) |
4.2 x 4.2 x 1.2 in. |
Weight | 1.06 lb or 480 g |
Specifications
|
Description |
---|---|
VLAN Support | Yes |
Number of VLANs | 1 management VLAN plus 16 VLANs for SSIDs (per radio) |
802.1X supplicant | Yes |
SSID-to-VLAN mapping | Yes |
Auto-channel selection | Yes |
Spanning tree | Yes |
Load balancing | Yes |
IPv6 |
Yes
IPv6 host support
IPv6 RADIUS, syslog, Network Time Protocol (NTP)
|
Layer 2 | 802.1Q-based VLANs, 32 active VLANs plus one management VLAN |
Specifications | Description |
---|---|
WPA, WPA2 | Yes, including Enterprise authentication |
Access control | Yes, management access control list (ACL) plus MAC ACL |
Secure management | HTTPS |
Rogue access point detection | Yes |
Specifications | Description |
---|---|
Wireless throughput | Up to 1.2 Gbps data rate (real-world throughput will vary) |
Recommended user support | Up to 128 connective users, 32 active users per radio |
Multiple-Access Point Management | |
Single Point Setup | No |
Number of access points per cluster | 8 |
Active clients per cluster | 240 |
Management | |
Management protocols | Web browser, Simple Network Management Protocol (SNMP) v3, Bonjour |
Remote management | Yes |
Event logging | Local, remote syslog, email alerts |
Network diagnostics | Logging and packet capture |
Web firmware upgrade | Firmware upgradable through web browser, imported and exported configuration file |
Dynamic Host Configuration Protocol (DHCP) | DHCP Client |
IPv6 host | Yes |
HTTP redirect | Yes |
Wireless | |
Frequency | Dual Concurrent radios (2.4 GHz and 5 GHz) |
Radio and modulation type |
Dual radio, orthogonal frequency division multiplexing (OFDM) IEEE 802.11 a/n: OFDM(BPSK/QPSK/16QAM/64QAM/256AM)
IEEE 802.11ac: OFDM (BPSK/QPSK/16QAM/64QAM/256QAM)
|
WLAN |
802.11n/ac
3x3 MIMO with 2 spatial streams at 5 GHz
3x3 MIMO with 2 spatial streams at 2.4 GHz
20-, 40-, and 80-Mhz channels for 802.11ac
20- and 40-Mhz for 802.11n
PHY data rate up to 1.2 Gbps
802.11 Dynamic Frequency Selection (DFS)
|
Data rates supported |
802.11a/b/g:
54, 48, 36, 24, 18, 12, 9, 6, 11, 5.5, 2, and 1 Mbps
802.11n: 6.5 to 300 Mbps:
20-MHz bandwidth: MCS 0-15 for supported data rates
40-MHz bandwidth: MCS 0-15 for supported data rates
802.11ac: 6.5 to 867 Mbps:
20-MHz bandwidth: MCS 0-9 for supported data rates
40-MHz bandwidth: MCS 0-9 for supported data rates
80-MHz bandwidth: MCS 0-9 for supported data rates
|
Transmitter output power | 2.4 GHz, 5 GHz |
System memory |
256 MB RAM
128 MB flash
|