Introduction
Q: Why the lina process on Firepower Threat Defense consumes 100% (or more) CPU?
A: This is normal because the lina process is constantly polling the Network Interface Cards (NICs) for input traffic. In short, the lina process utilization can be safely ignored.
Contributed by Mikis Zafeiroudis, Ignacio Penalva, Haitham Jaradat and David Torres Rivas, Cisco TAC Engineers.
Analysis
Firepower Threat Defense is a unified operating system consisting of 2 engines (ASA and Snort).
The FTD CLI shows that 'lina' process (ASA engine) consumes a lot of CPU cycles. Here is an example from an FTD running on ASA5506-X appliance:
> system support utilization
top - 01:26:40 up 12 days, 16:00, 1 user, load average: 22.08, 22.10, 22.10
Tasks: 161 total, 1 running, 159 sleeping, 0 stopped, 1 zombie
Cpu(s): 22.6%us, 4.1%sy, 0.0%ni, 73.2%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st
Mem: 3927684k total, 2793860k used, 120904k free, 181548k buffers
Swap: 3996668k total, 257632k used, 3739036k free, 831372k cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
23000 root 0 -20 1138m 513m 91m S 99 13.4 18205:20 lina <--
2952 admin 20 0 15240 1156 848 R 2 0.0 0:00.02 top
22941 root 20 0 266m 2316 2108 S 2 0.1 47:16.70 ndmain.bin
1 root 20 0 4232 652 620 S 0 0.0 0:12.40 init
In the above output you should actually take into consideration the us (user) + sy (system) CPU utilization along with the id (idle - not used) value.
Here is from an FTD running on FPR-9300 appliance:
> system support utilization
top - 04:30:22 up 40 days, 5:22, 0 users, load average: 26.12, 26.10, 26.13
Tasks: 568 total, 1 running, 566 sleeping, 0 stopped, 1 zombie
Cpu(s): 22.1%us, 0.2%sy, 0.0%ni, 77.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Mem: 264374828k total, 28976700k used, 234868048k free, 268k buffers
Swap: 0k total, 0k used, 0k free, 529812k cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
12772 root 0 -20 24.8g 541m 88m S 1593 0.2 927288:05 lina <--
12594 mysql 20 0 3063m 150m 9140 S 4 0.1 56:28.39 mysqld
12608 root 20 0 24696 2848 1192 S 2 0.0 422:45.07 pdts_proc
43145 admin 20 0 15648 1484 844 R 2 0.0 0:00.01 top
1 root 20 0 4232 632 552 S 0 0.0 0:15.43 init
Recommendations
- In the 'system support utilization' ignore the 'lina' process utilization.
- To monitor the FTD CPU utilization check the 'us' + 'sys' + 'id' values
- Regarding the monitoring of the ASA engine you should check the following outputs:
Output 1
> show cpu usage
CPU utilization for 5 seconds = 0%; 1 minute: 0%; 5 minutes: 0%
Output 2
> show processes cpu-usage sorted non-zero
PC Thread 5Sec 1Min 5Min Process
0x00007f42428f1fd9 0x00007f42290b9ea0 0.2% 0.0% 0.0% ci/console