Summary

• A vulnerability in the Simple Network Management Protocol version 3 (SNMPv3) access control functionality of Cisco Adaptive Security Appliance (ASA) Software and Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to query SNMP data.

  This vulnerability is due to ineffective access control. An attacker could exploit this vulnerability by sending an SNMPv3 query to an affected device from a host that is not permitted by the SNMPv3 access control list. A successful exploit could allow the attacker to send an SNMP query to an affected device and retrieve information from the device. The attacker would need valid credentials to perform the SNMP query.

  Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.

  This advisory is available at the following link:
  https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asaftd-snmpaccess-M6yOweq3

  This advisory is part of the October 2021 release of the Cisco ASA, FTD, and FMC Security Advisory Bundled publication. For a complete list of the advisories and links to them, see Cisco Event Response: October 2021 Cisco ASA, FMC, and FTD Software Security Advisory Bundled Publication.

Affected Products

• Vulnerable Products

  At the time of publication, this vulnerability affected Cisco Adaptive Security Appliances and Cisco Firepower Appliances if they were running a vulnerable release of Cisco ASA Software or FTD Software and had SNMPv3 access control configured.

  For information about which Cisco software releases were vulnerable at the time of publication, see the Fixed Software section of this advisory. See the Details section in the bug ID(s) at the top of this advisory for the most complete and current information.

  Determine the Device Configuration

  To determine whether an SNMPv3 user-based access control entry is configured, run the show running-config snmp-server CLI command and check for the presence of version 3 in the output. The following output shows a configured SNMPv3 access entry:

  ASA# show running-config snmp-server | include host
  snmp-server host internalMgmt 10.10.10.10 version 3 snmpUser
  snmp-server host internalMgmt 10.11.12.13 community snmpCommunity
  ASA#

   

  Products Confirmed Not Vulnerable

  Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.

  Cisco has confirmed that this vulnerability does not affect Cisco Firepower Management Center (FMC) Software.

Workarounds

• There are no workarounds that address this vulnerability.

Fixed Software

• When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page, to determine exposure and a complete upgrade solution.

  In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.

  Fixed Releases

  At the time of publication, the release information in the following table(s) was accurate. See the Details section in the bug ID(s) at the top of this advisory for the most complete and current information.

  The left column lists Cisco software releases, and the right column indicates whether a release was affected by the vulnerability described in this advisory and which release included the fix for this vulnerability.

  ASA Software

  Cisco ASA Software Release	First Fixed Release for This Vulnerability
  Earlier than 9.81	Not vulnerable.
  9.8	Not vulnerable.
  9.91	Not vulnerable.
  9.101	Not vulnerable.
  9.12	Not vulnerable.
  9.131	Not vulnerable.
  9.14	9.14.2.4
  9.15	9.15.1.7
  9.16	Not vulnerable.

  1. Cisco ASA Software releases 9.7 and earlier as well as releases 9.9, 9.10, and 9.13 have reached end of software maintenance. Customers are advised to migrate to a supported release that includes the fix for this vulnerability.

  FTD Software

  Cisco FTD Software Release	First Fixed Release for This Vulnerability
  6.2.2 and earlier1	Not vulnerable.
  6.2.3	Not vulnerable.
  6.3.01	Not vulnerable.
  6.4.0	6.4.0.13 (Nov 2021)
  6.5.01	Migrate to a fixed release.
  6.6.0	6.6.5
  6.7.0	6.7.0.1
  7.0.0	Not vulnerable.

  1. Cisco FMC and FTD Software releases 6.2.2 and earlier, as well as releases 6.3.0 and 6.5.0, have reached end of software maintenance. Customers are advised to migrate to a supported release that includes the fix for this vulnerability.

  For instructions on upgrading your FTD device, see Cisco Firepower Management Center Upgrade Guide.

  The Cisco Product Security Incident Response Team (PSIRT) validates only the affected and fixed release information that is documented in this advisory.

Exploitation and Public Announcements

• The Cisco PSIRT is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.

Source

• This vulnerability was found during internal security testing.

URL

• https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asaftd-snmpaccess-M6yOweq3

Revision History

• Version	Description	Section	Status	Date
  1.0	Initial public release.	—	Final	2021-OCT-27

  Show Less

---