Table Of Contents
Alphabetical List of Commands dchst through window
dchst (display channel status)
delalmslot (delete alarm slot)
delapsln (delete a SONET APS line)
delctrlr (delete MPLS controller from an IGX)
delctrlr (delete VSI capabilities from an AAL5 feeder interface)
delfrport (delete Frame Relay port using T1 or E1 lines)
deljobtrig (delete a job trigger)
dellp (delete loopback from connections or a port)
delshelf (delete an interface shelf)
deltrk (delete a trunk from the network)
deltrkred (delete ATM trunk redundancy)
delyred (delete Y-cable redundancy)
diagbus (diagnose failed IGX bus)
drtop (display route op table)
dspabortlog (display abort log)
dspalms (display current node alarms)
dspasich (display ASI channel routing entry)
dspatmcls (display ATM connection class)
dspbmpparm (display priority bumping parameters)
dspbmpstats (display priority bumping statistics)
dspbpnv (display backplane NOVRAM)
dspbusbw (display cell bus bandwidth for UXM cards)
dspcdstats (display UXM card statistics)
dspcbause (display CBA block usage)
dspcderrs (display card errors)
dspcdred (display redundant cards)
dspcftst (display communication fail test pattern)
dspchan (display channel configuration)
dspchcnf (display channel configuration)
dspchdlcnf (display channel dial type configurations)
dspchec (display channel echo canceller configuration)
dspchstatcnf (display statistics enabled for a channel)
dspchstathist (display statistics history for a channel)
dspchstats (display summary statistics for a channel)
dspchuse (display channel usage)
dspclksrcs (display network clock sources)
dspclnerrs (display circuit line errors)
dspclnstatcnf (display circuit line statistics configuration)
dspclnstathist (display statistics history for a circuit line)
dspcls (display connection class)
dspcnf (display configuration save/restore status)
dspcntrstats (display counter status statistics)
dspcon (display data connections)
dspcon (display Frame Relay connections)
dspcon (display ATM connections)
dspconcnf (display connection configuration)
dspcond (display conditioning criteria)
dspconst (display connection state for line connections)
dspctrlrs (display all controllers on a BPX node)
dspcurclk (display current clock sources)
dspdutl (display data channel utilization)
dspecparm (display echo canceller parameters)
dspeventq (display event queue)
dspfrcbob (display FRC/FRM breakout box)
dspfrcls (display Frame Relay classes)
dspfrcport (display FRC-2/FRM-2 port configuration)
dspfwrev (display firmware revision)
dsphitless (display statistical history of hitless rebuilds)
dspict (display interface control template)
dsplancnf (display LAN interface connection)
dsplanip (display LAN IP addresses)
dsplm (display load model table)
dsplmistats (display Annex G LMI statistics)
Functional Description of LMI Statistics for BXM Card
dsplnalmcnf (display line alarm configuration)
dsplncnf (display line configuration)
dsplnerrs (display line errors)
dsplnstathist (display statistics data for a line)
dspload (display connection loading)
dspnebdisc (display neighbor discovery)
dspnwip (display network IP interface)
dspoamseg (display connection OAM segment status)
dspospace (display open space for a route)
dsppcs (display port concentrator shelf)
dspphyslnerrs (display physical line errors)
dspphyslns (display physical line status)
dspphyslnstatcnf (display statistics enabled for a physical line)
dspphyslnstathist (display statistics data for a physical line)
dspportq (display ARM port queue configuration)
dspportstatcnf (display statistics enabled for FR port)
dspportstathist (display statistics history for an FR port)
dspportstats (display Frame Relay port statistics)
dspportstats (display ATM port statistics)
dspprtcnf (display print configuration)
dsppwr (display power supply status)
dspqbinstats (display Qbin statistics)
dspqbint (display Qbin templates)
dsprobst (display robust statistics)
dsprrst (display reroute statistics)
dsprtcache (display cost-based route cache)
dsprtrcnfdnld (display status of router configuration file)
dsprtrslot (display router slot)
dsprtrslots (display router slots)
dsprts (display connection routing)
dspsct (display Service Class Template)
dspsigqual (display signaling qualifiers)
dspslotalmcnf (display slot alarm configuration)
dspslotalms (display slot alarms)
dspsloterrs (display slot errors)
dspslotstatcnf (display statistics enabled for a BXM card slot)
dspslotstathist (display statistics history for a BXM card)
dspsnmp (display SNMP parameters)
dspsnmpstats (display SNMP statistics)
dspstatfiles (display TFTP statistics file information)
dspstatmem (display statistics memory use)
dspsv3 (display WAN manager L3 link control blocks)
dspsvcst (display the voice SVC statistics)
dspswlog (display software error log)
dsptcpparm (display TCP parameters)
dsptermcnf (display terminal port configurations)
dsptermfunc (display terminal port functions)
dsptrkbob (display trunk breakout box)
dsptrkcnf (display trunk configuration)
dsptrkcons (display trunk connection counts)
dsptrkerrs (display trunk errors)
dsptrkict (display trunk interface control templates)
dsptrkmcons (display trunk connection counts by master node)
dsptrkred (display ATM trunk redundancy)
dsptrkstatcnf (display statistics enabled for a trunk)
dsptrkstathist (display statistics history for a trunk)
dsptrkstats (display trunk statistics)
dsptrkutl (display trunk utilization)
dsptsmap (display the channel-to-timeslot mapping usage)
dsptsmap (display SNMP parameters)
dspusertask (display user task)
dspusertasks (display user tasks)
dspvsiif (display a Service Class Template assigned to an interface)
dspvsipartcnf (display VSI partition characteristics)
dspvsipartinfo (display VSI statistics per partition)
dspyred (display Y-cable redundancy)
getfwrev (get firmware revision)
prtapsln (print APS line status)
prtchcnf (print channel configuration)
prtchdlcnf (print channel dial type configuration)
prtclnerrs (print circuit line errors)
prtict (print interface control template)
prtlnerrs (print physical line errors)
prtlns (print line configuration)
prtnw (print network topology)
prtrts (print connection routes)
prtscrn (print terminal screen)
prttrkerrs (print trunk errors)
prttrkict (print trunk interface control template)
prtyred (print Y-cable redundancy)
redscrn (redraw the terminal screen)
resetpc (reset port concentrator)
rststats (reset statistics collection time)
TFTP Configuration Save and Restore
switchapsln (control APS switching interface)
switchcc (switch control card)
switchyred (switch Y-redundancy cards)
tstbadubus (test NTM corruption problem)
tstconseg (test connection segment)
tstdelay (test connection round-trip delay)
tstpcs (test port concentrator shelf)
upgdlogcd (upgrade logical card database)
upgdvsilcn (expand VSI LCN to 60K for BXM-E)
vt (make a virtual connection)
window (window to external device)
Alphabetical List of Commands dchst through window
dchst (display channel status)
Displays CDP or CVM card parameters.
This command displays state information for a CDP or CVM channel used for a specific connection.
The Transmit and Receive dBm0 for both CDP or CVM indicate the input (toward the circuit line) and output power (from the circuit line) levels for the channel. Modem state indicates whether modem-detect is on or off.
Syntax
dchst <channel> [interval]
Parameters
<channel(s)>
Specifies the voice channel numbers to configure.
<interval>
Specifies the refresh time for the data.
Range: 1-60 seconds
Default: 5 seconds
Display Fields: Channel Status Parameters for CDP or CVM
Attributes
Related Commands
cnfcdpparm
Example
dchst 11.1
alpha TRM SuperUser Rev: 9.3 Apr. 13 2000 16:30 PSTCDP state display for channel 11.1 SnapshotTransmit dBm0:Receive dBm0:Register 0 =Register 1 =Register 2 =Register 3 =Register 4 =Register 5 =Register 6 =Last Command: dchst 11.1Next Command:delalmslot (delete alarm slot)
Disables the ARC (IPX) or ARM (IGX) alarm indicators and ARI external alarms. See the addalmslot description for more information on ARC/ARM alarm relays and adding alarm slots.
Upon receiving the command, the system places the alarm card set in the standby state and displays the current alarm status.
Syntax
delalm <slot number>
Parameters
Attributes
Related Commands
addalmslot, dspalms
Example
Disable the alarm indicators on the ARM card set in slot 11. (The system subsequently displays alarm status.)
delalmslot 11
pubsigx1 TN SuperUser IGX 8430 9.3 Apr. 13 2000 02:09 GMTAlarm summary (Configured alarm slots: None)Connections Failed: NoneGroups Failed: NoneTRK Alarms: NoneLine Alarms: NoneCards Failed: NoneMissing Cards: NoneRemote Node Alarms: 1 MinorRemote Domain Alarms: NoneRouting Network Alarms: NoneCabinet Fan(s) FailedFastPAD Node Alarms: NoneLast Command: delalmslot 11Next Command:delapsln (delete a SONET APS line)
The delapsln command deletes SONET Automatic Protection Switching (APS) for the lines. You must enter the working slot.port pair. When you execute the delapsln command, the dspapsln display appears, showing you that the line you deleted is gone. (The delapsln display will be empty, or show only the remaining APS lines.)
SONET APS is a standard that describes the switching of SONET lines from the active line to a standby line to provide hardware line redundancy. The SONET APS feature applies only to BXM OC-3 and OC-12 cards in this release.
For background information on how SONET APS for BXM cards works, refer to "APS Command Summary" in this chapter.
When you execute the delapsln command, the switch software does verifies that the slot.port arguments support APS.
Syntax
delapsln <slot.port1> < slot.port2> <protocol>
Parameters
Attributes
Related Commands
addapsln, cnfapsln, cnfcdaps, dspapsln, dsplog, dspalms
Example
delapsln 11.1
sw119 TRM StrataCom BPX 8620 9.3.10 Date/Time Not SetWork/Protect Actv Active Line Standby Line Current APS Last User(Work1/Work2)Line Alarm Status Alarm Status Alarm Status Switch ReqLast Command: delapsln 11.1delcon (delete connection)
Removes connections from the network. The same command with differing syntax may be used to delete voice connections, data connections, Frame Relay connections, or ATM connections.
You can use delcon to delete data or FRP connections that are terminated on UXM/UXM-E cards for IGX 8400 interface shelves, and terminated on routing network feeder trunks for IGX 8400 routing nodes.
You can use delcon to remove one or more voice connections from a network. You can delete connections at either end of the connection. After entry of the channel or range of channels to delete, a prompt requests confirmation of the selection.
Do not delete a connection when the node at the other end of the connection is unreachable. The unreachable node does not recognize the deletion. You must not delete a connection to an unreachable node then connect that deleted channel to another node.
To verify connection deletions, use the dspcons command. To add channel connections to the network, use the addcon command.
Syntax
delcon <channels>
Parameters
Attributes
Related Commands
addcon, dspcon, dspcons
Example
Delete connection 10.1.1. The proposed deletions are highlighted, and a prompt requests confirmation of the deletion. Enter a "y" to delete the highlighted connections or an "n" to keep the highlighted connections. The example shows the screen before deletion of 10.1.1.
delcon 10.1.1
igxr03 VT Cisco IGX 8430 9.3.2V Jan. 18 2001 12:24 PSTFrom Remote Remote10.1.1 NodeName Channel State Type Compress Code COS10.1.1 igxr02 20.1.1 Ok p 010.1.3-4 igxr02 20.1.3-4 Ok v VAD 210.1.5-6 igxr02 20.1.5-6 Ok t 010.1.9-10 igxr02 20.1.9-10 Ok a24 ADPCM 210.1.11-12 igxr02 20.1.11-12 Ok c24 VAD/ADPCM 210.1.13-14 igxr02 20.1.13-14 Ok a32 ADPCM 210.1.15-16 igxr02 20.1.15-16 Ok c32 VAD/ADPCM 210.1.19-20 igxr02 20.1.19-20 Ok l16v VAD/LDCELP 210.2.1 igxr02 20.2.1 Ok p 010.2.3-4 igxr02 20.2.3-4 Ok a24 ADPCM 210.2.5-6 igxr02 20.2.5-6 Ok a32 ADPCM 210.2.7 igxr02 20.2.7 Ok l16 LDCELP 210.2.9 igxr02 20.2.9 Ok l16v VAD/LDCELP 2This Command: delcon 10.1.1Delete these connections (y/n)?Example
Delete connection 6.4.
delcon 6.4
igxr03 VT Cisco IGX 8430 9.3.2V Jan. 18 2001 12:38 PSTFrom Remote Remote6.4 NodeName Channel State Type Compress Code COS6.4 igxr02 18.4 Ok 128 DFM 7/8 010.1.1 igxr02 20.1.1 Ok p 010.1.3-4 igxr02 20.1.3-4 Ok v VAD 210.1.5-6 igxr02 20.1.5-6 Ok t 010.1.9-10 igxr02 20.1.9-10 Ok a24 ADPCM 210.1.11-12 igxr02 20.1.11-12 Ok c24 VAD/ADPCM 210.1.13-14 igxr02 20.1.13-14 Ok a32 ADPCM 210.1.15-16 igxr02 20.1.15-16 Ok c32 VAD/ADPCM 210.1.19-20 igxr02 20.1.19-20 Ok l16v VAD/LDCELP 210.2.1 igxr02 20.2.1 Ok p 010.2.3-4 igxr02 20.2.3-4 Ok a24 ADPCM 210.2.5-6 igxr02 20.2.5-6 Ok a32 ADPCM 210.2.7 igxr02 20.2.7 Ok l16 LDCELP 2This Command: delcon 6.4Delete these connections (y/n)?Example
Delete connection 14.3.4. The connections to delete are highlighted. A prompt asks you to confirm the deletion. Respond with "y" for yes.
delcon 14.3.4
igxr03 VT Cisco IGX 8430 9.3.2V Jan. 18 2001 12:56 PSTFrom Remote Remote14.3.4 NodeName Channel State Type Compress Code COS14.3.4 igxr02 27.3.4 Ok fr 014.3.5 igxr02 27.3.5 Ok fr 014.3.6 igxr02 27.3.6 Ok fr 014.3.7 igxr02 27.3.7 Ok fr 014.3.8 igxr02 27.3.8 Ok fr 014.3.9 igxr02 27.3.9 Ok fr 014.3.10 igxr02 27.3.10 Ok fr 014.3.11 igxr02 27.3.11 Ok fr 014.3.12 igxr02 27.3.12 Ok fr 014.3.13 igxr02 27.3.13 Ok fr 014.3.14 igxr02 27.3.14 Ok fr 014.3.15 igxr02 27.3.15 Ok fr 014.3.16 igxr02 27.3.16 Ok fr 0This Command: delcon 14.3.4Delete these connections (y/n)?Example
Delete connection 11.1.180.150. The connections to delete are highlighted, and a prompt appears asking you to confirm the deletion. Respond with "y", for yes, and connection 11.1.180.150 is deleted.
delcon 11.1.180.150
sw53 VT Cisco BPX 8620 9.3.m0 Dec. 19 2000 09:57 GMTFrom Remote Remote Route11.1.180.150 NodeName Channel State Type Avoid COS O11.1.180.150 sw180 15.1.11.100 Ok ubr 0 R11.1.180.530 sw180 5.3.53.530 Ok ubr 0 L11.1.180.1000 sw180 15.1.53.1000 Ok nrt-vbr 0 L11.1.180.1001 sw180 15.1.53.1001 Ok abrstd 0 LThis Command: delcon 11.1.180.150Delete these connections (y/n)?delctrlr (delete MPLS controller from an IGX)
Deletes an MPLS controller attached to a line on a UXM card.
When the controller is deleted, the VSI control channels used to communicate between the VSI master on the MPLS controller and the VSI slaves on the UXM cards are also deleted. The control VCs associated with other controllers attached to the node will not be affected.
Syntax
delctrlr <controller id>
Parameters
controller id
Controller ID number corresponding to the MPLS controller you are deleting. ID numbers should correspond to an active MPLS controller.
Range: 1-16
Attributes
Related Commands
addctrlr, dspctrlrs
Example
Delete an MPLS controller.
delctrlr 3
arnold TN Cisco IGX 8430 9.3.1p Aug. 16 2000 17:12 PSTVSI Controller InformationCtrlrId PartId ControlVC Intfc Type CtrlrIPVPI VCIRangeLast Command: delctrlr 3Controller deleted successfully!Next Command:delctrlr (delete VSI capabilities from an AAL5 feeder interface)
Deletes VSI capabilities on a trunk interface to which a feeder of type AAL5 is attached. Use this command to delete a controller, such as a PNNI SES controller, from a BPX node. It deletes the VSI control channels used to communicate between the VSI master on the PNNI controller and the VSI slaves on the BXM cards.
Run this command as the first step in deleting a PNNI controller from a BPX node. The second step is to run the command to delete the AAL5 feeder.
Note
Do not use delctrlr to delete a VSI Label Switching controller from a BPX node; you must use delshelf to delete a VSI Label Switching controller from a BPX node.
PNNI runs on the Service Expansion Shelf (SES) hardware.
To add VSI controller capabilities onto the newly created AAL5 interface, you use the addctrlr command. You are prompted to enter the controller ID and partition ID. This creates an interface through which a PNNI controller can use the VSI protocol to control the node resources that were previously specified by using the cnfrsrc command.
Remove a PNNI controller from a node by using the delctrlr command. For example, this might be a VSI controller such as a PNNI controller configured with VSI capabilities as an AAL5 interface shelf to a BPX. When you delete one of the controllers by using the delctrlr command, the master-slave connections associated with this controller are deleted. The control VCs associated with other controllers managing the same partition will not be affected.
Note
Syntax
delctrlr <slot.port> <controller id>
Parameters
Attributes
Related Commands
addctrlr, dspctrlrs, dspnode
Example
Delete VSI controller with interface shelf (feeder) type of AAL5 connected on trunk 10.3 from the list of controllers connected to BPX node named "night."
delctrlr 10.3
night TN StrataCom BPX 8600 9.3.10 Apr. 11 2000 14:31 GMTBPX Controllers InformationTrunk Name Type Part Id Ctrl Id Ctrl IP State10.3 PAR VSI 1 2 192.0.0.0 Enabled11.1 VSI VSI 2 2 192.0.0.0 DisabledLast Command: delctrlr 10.3Example
Deletes controller from port 3 on slot 10, with controller name E, and controller ID of 1.
delctrlr <slot.port><controller_id>
night TN StrataCom BPX 8600 9.3.10 Apr. 11 2000 14:31 GMTBPX Controllers InformationTrunk Name Type Part Id Ctrl Id Ctrl IP State10.3 PAR VSI 1 1 192.0.0.0 Enabled11.1 VSI VSI 2 2 192.0.0.0 DisabledLast Command: delctrlr 10.3delfrport (delete Frame Relay port using T1 or E1 lines)
Deletes logical ports on FRP, FRM, or UFM-C cards and "unassigns" associated DS0/timeslots. The information in this definition applies only to Frame Relay ports using a T1 or E1 line.
The deleted DS0/timeslots are available for you to assign to new logical ports by using the addport (alias addfrport) command. The port display (normally visible through dspport [alias dspfrport] command) appears regardless of whether the port has been successfully deleted. The screen displays the defined port numbers for the specified line. Table 4-1 lists the error and warning messages for this command.
Syntax
For FRM or FRP:
delfrport <slot.port>For UFM:
delfrport <slot.port> <line.ds0_range>Parameters
Attributes
Related Commands
addfrport, dspfrport
Example
Delete Frame Relay port 14.1.
delfrport 14.1
igxr03 VT Cisco IGX 8430 9.3.2V Jan. 18 2001 13:04 PSTPort configuration for UFM 14Port Line Chan Speed Interface State Protocol1 1 1-24 1536 Kbps T1D ACTIVE None2 2 1-24 1536 Kbps T1D ACTIVE None3 3 1-24 1536 Kbps T1D ACTIVE None4 4 1-24 1536 Kbps T1D ACTIVE NoneThis Command: delfrport 14.1You must first down the portEnter port:deljob (delete a job)
Deletes a job. To delete a job, you must have a privilege level at least as high as the job itself. A job that is currently running cannot be deleted. If necessary, use stopjob to stop the job so that you can delete it.
Syntax
deljob <job_number>
Parameters
Attributes
Related Commands
addjob, dspjob, dspjobs
Example
Delete job 4.
deljob 4
pubsigx1 TN SuperUser IGX 32 9.3 Apr. 13 2000 19:54 GMTJob 4Last Execution Results: None Status: LockedNext Execution Time: Interval:1: prtlog- Failure Reaction: Abort Exec. Results: None2: dncd 6- Failure Reaction: Repeat 12 Times and Abort Exec. Results: None3: dncd 6- Failure Reaction: Repeat 12 Times and Continue Exec. Results: NoneThis Command: deljob 4Delete this job (y/n)?deljobtrig (delete a job trigger)
Deletes a job trigger. The deljobtrig command deletes one trigger at a time. If you delete a job by using the deljob command, all associated job triggers are deleted.
Syntax
deljobtrig <job_number> <trig_num>
Parameters
<job_number>
Specifies the number of the job.
<trig_num>
Specifies the number of the trigger to delete.
Attributes
Related Commands
addjobtrig, dspjobs
Example
Delete job trigger 1 for job 1.
deljobtrig 1 1
pubsigx1 TN SuperUser IGX 32 9.3 Apr. 13 2000 18:19 GMTJob Description Next Execution Status Interval Access Group1 test1 Idle SuperUserTrigger 1 - PLN 2 FAILURE2 Idle SuperUser3 test3 09/02/97 11:11:11 Idle 1 days SuperUser4 Idle SuperUser5 Idle SuperUser6 Idle SuperUserThis Command: deljobtrig 1Enter trigger number:dellp (delete loopback from connections or a port)
Deletes an external, local, remote, or local-remote (tiered nets) loopback from the designated channel, set of channels, or port. After the loopback is deleted, any conditioning applied during the loopback process is removed and service is restored.
•
•
•
A local loop can be deleted only from the node that added it. However, a remote loop can be deleted from the node at either end of the connection.
Add local-remote loopbacks by using the addlocrmtlp command. Note that with local-remote loopbacks, execution of dellp is mandatory after testing is complete, otherwise continuity errors will result.
The addloclp and addlocrmtlp commands support the two-segment connection at the hub node port endpoint in a network of IGX routing hubs and SES interface shelves. The addloclp and addlocrmtlp commands are blocked at the interface shelf trunk endpoint. The addrmtlp command is not supported at either endpoint of the connection. You can use the dellp command to remove the local (or local remote) loopbacks that have been added; however, you cannot use the dellp command at the trunk endpoint of the connection—it will be blocked. Loops of any kind are not supported for the middle segment of a three-segment connection.
Syntax
dellp <channel>
Parameters
Attributes
Related Commands
addextlp, addloclp, addlocrmtlp, addrmtlp
Example
Delete the loopback on channel 5.1.121. The connections screen appears with connection 5.1.121 highlighted. (The highlighting is not visible in the screen example, but the loop symbols indicates loopback.) The display prompts you to confirm deletion of the loopback. To confirm, enter "y."
dellp 5.1.121
pubsipx1 TN SuperUser IGX 8420 9.3 Apr. 13 2000 19:16 PDTLocal Remote RemoteChannel NodeName Channel State Type Compress Code COS5.1.121 )pubsipx1 8.33.133 Ok atfr5.1.122 pubsipx1 8.34.134 Ok atfr5.2.111 pubsipx1 8.45.155 Ok atfr5.2.112 pubsipx1 8.45.156 Ok atfr8.33.133 pubsipx1 (5.1.121 Ok atfr8.34.134 pubsipx1 5.1.122 Ok atfr8.45.155 pubsipx1 5.2.111 Ok atfr8.45.156 pubsipx1 5.2.112 Ok atfrThis Command: dellp 5.1.121Delete these loopbacks (y/n)?delport (delete port)
This command is required to delete ports from the IGX and BPX. Use this command to:
•
•
•
The dnport command is required before the ports can be deleted.
Syntax
delport <slot.port>[.<vport>]
Parameters
<slot.port>
Specifies the slot number of the card, the physical port, and optional virtual port (BXM card only).
[.<vport>]
The optional vport identifier. Range: 1-31
Attributes
Related Commands
addport, upport cnfport, dnport
Example
Delete the internal ATM port 11.1 on the Universal Router Module (URM) in an IGX node.
delport 11.1
sw190 TRM Cisco IGX 8420 9.3.e9 Oct. 6 2000 05:23 GMTPort configuration for ATM 11Port Chan Speed Interface State Protocol TypeLast Command:delport 11.1Example (BPX)
Delete port 3 on the BXM card in slot 11.
delport 11.3
sw53 TN Cisco BPX 8620 9.3.m0 Dec. 19 2000 12:45 GMTPort configuration for ATM 11From VPI Min/Max Bandwidth Interface State Protocol TypeLast Command: delport 11.3delshelf (delete an interface shelf)
Deletes an interface shelf from a tiered network. The identifier for an interface shelf is either the trunk number or the name of the shelf. Normally, you do not execute delshelf only at the hub node or the BPX core switch shelf, but on the IGX/AF itself.
The delshelf command has the single function of letting you turn off LMI if the trunk is not allowing communication. In contrast to the deltrk command, you can execute delshelf at any time if no connections terminate at the trunk.
In Release 9.2 and above, when you use delshelf to remove an MGX 8850 interface shelf trunk from a BPX routing hub, or an SES interface shelf (or feeder) trunk from an IGX 8400 routing node, the Annex G signaling channel and IP relay programming for the MGX 8850 or SES interface shelf is removed.
Deleting a Controller
You remove a controller from the node by using the delshelf command. When one of the controllers is deleted by using the delshelf command, the master-slave connections associated with this controller is deleted. The control VCs associated with other controllers managing the same partition are not affected.
The deletion of the controller triggers a new VSI configuration CommBus (internal BPX protocol) message that includes the list of the controllers attached to the node and is sent to all active slaves in the shelf. The controller deleted is removed from the list. In cluster configurations, deleting a controller is communicated to the remote slaves by the slave directly attached through the interslave protocol.
While there is at least one controller attached to the node controlling a given partition, the resources in use on this partition should not be affected by the deletion of a controller. The slaves release all the VSI resources used on a partition only when that partition is disabled.
Syntax
delshelf <trunk> | <shelf-name>
Parameters
trunk or shelf name
Specifies the slot and port number of the trunk or the name of the interface shelf.
Related Commands
addshelf, dspnode
Attributes
Example
Delete shelf trunk A241 from a BPX node.
delshelf 4.1
nmsbpx23 TN SuperUser BPX 8600 9.3.10 July 16 2000 13:26 PSTBPX Interface Shelf InformationTrunk Name Type Alarm1.3 AXIS240 AXIS OK11.2 A242 AXIS OKLast Command: delshelf A241Shelf has been deletedNext Command:deltrk (delete a trunk from the network)
Deletes a trunk. Because deleting a trunk removes the communication path between two nodes, using deltrk may split a network into two separate networks. If executing deltrk splits the network, then the connections that are using the deleted trunk are also deleted.
If both nodes on the trunk are reachable, you need only to execute deltrk on one node. If you delete a trunk on a node while the node at the other end is unreachable, the unreachable node does not detect that the trunk to the other node has been deleted; therefore, be sure to delete the trunk at both nodes in such a case.
After you delete a trunk, it still carries framing signals but no traffic. Also, the trunk can generate alarms for counting. To remove a trunk completely, use dntrk after executing the deltrk command.
In these situations, the node does not allow deltrk to execute:
•
•
•
In Release 9.1.07, when the A-bit Notifications on LMI/ILMI Interface feature is enabled (by using cnfnodeparm), after deleting the trunk, the master node will deroute all the connections on the trunk. The slave end will receive the A7 (CMUP_DEROUTE) message before the reroute message from the master node.
Regarding the A-bit Notifications feature, each pass in the Connection Management routing state machine involves two activities: deroute and then followed by routing connections. However, connections can be derouted without going through the reroute state machine (for example, deltrk). There are several ways to kick off the routing state machine resulting in slightly different deroute and reroute behavior. See the deltrk, dncd, and cnfcmparm (SuperUser) commands.
Syntax
deltrk <slot.port>[.vtrk]
Parameters
<slot.port>
Specifies the physical trunk number.
[.vtrk]
Optionally specifies the virtual trunk portion of the trunk identifier.
Attributes
Related Commands
addtrk, dntrk, dspnw, dsptrks, uptrk
Example
Delete trunk 7 from the network.
deltrk 7
beta TRM YourID:1 IGX 8430 9.3 Apr. 13 2000 15:02 MSTPLN Type Current Line Alarm Status Other End7 E1/32 Clear - Line OK -9 T1/24 Clear - Line OK gamma.1013 T1/24 Clear - Line OK alpha.1415 T1/24 Clear - Line OK gamma.1520 T3/3 AIT - AIT Missing -Last Command: deltrk 7Next Command:deltrkred (delete ATM trunk redundancy)
Removes redundancy from a UXM, or AIT trunk. After you execute deltrkrd, you can remove the backup card without causing an alarm.
The trunk redundancy feature (not the Automatic Protection Switching redundancy feature) is supported on the IGX platforms. This is different from the Automatic Protection Switching redundancy feature. APS is supported only on BXM SONET trunks, and can be used with virtual trunks. That is, the trunk port supporting virtual trunks can have APS line redundancy configured in the same way it would be configured for a physical trunk. The APS commands addapsln, delapsln, switchapsln, and cnfaplsn are all supported on virtual trunk ports.
Note that the trunk redundancy feature is not supported for virtual trunks. The addtrkred, deltrkred, and dsptrkred commands are rejected for virtual trunks.
Note that Y-cable redundancy is supported for both the UXM and BXM trunk cards at the edge of the ATM cloud.
Syntax
deltrkred <backup ATM trunk number>
Parameters
<backup ATM trunk number>
Specifies of the ATM card set assigned as the backup.
Attributes
Related Commands
addtrkred, dsptrkred
Example
Remove ATM trunk redundancy for the card set in slot 5.
deltrkred 5
beta TRM YourID:1 IGX 8430 9.3 Apr. 13 2000 15:15 MSTATM Line Backup ATM Line5 8Last Command: deltrkred 5Next Command:deluser (delete a user)
Deletes a user from the network. You can delete users at any lower privilege level.
Syntax
deluser <user_id>
Parameters
Attributes
Related Commands
adduser, dspusers
Example
deluser john
Delete the user named "john."
alpha TRM YourID:1 IGX 8410 9.3 Apr. 13 2000 13:52 PSTYourID 1Sarah 5\Last Command: deluser JohnNext Command:delyred (delete Y-cable redundancy)
This command disables Y-cable redundancy for the card set in the specified primary slot number. If the secondary card slot is in use as the active slot at the time you use the delyred command, the system attempts to switch back to the primary slot. The substitution takes place only if the primary slot has a complete set of cards and the cards are in a Standby or a Standby-F state (not if they are Failed).
See the dspcds description for information on card states. See the addyred and dspyred commands for more information on Y-cable redundancy.
When you issue the delyred command, it always completes. If the primary card is incomplete, control is given to the primary card.
If the secondary card slot is being used as the active slot at the time you use the delvred command, the system attempts to switch back to the primary slot. The substitution takes place only if the primary slot has a complete set of cards and the cards are in a Standby or a Standby-F state (not if they are Failed). See the dspcds description for information on card states.
Because YRED (Y redundancy) could be considered a misnomer for the SONET APS two-slot case, these alias commands support card redundancy:
•
•
•
•
•
Syntax
delyred <primary slot>
Parameters
<primary slot>
Specifies the number of the primary slot for which you are deleting Y-cable redundancy.
Attributes
Related Commands
addyred, dspyred, prtyred
Example (IGX)
Disable Y-cable redundancy at slot 12.
delyred 12
arnold TN Cisco IGX 8430 9.3.1p Aug. 16 2000 17:31 PSTSlot Other Front Back Channel ConfigurationSlot Type Slot Card Card 1 2 3 4 5 6 7 8Last Command: delyred 12Next Command:Example (BPX)
Disable Y-cable redundancy at slot 2.
delyred 2
sw53 VT Cisco BPX 8620 9.3.2o Dec. 6 2000 10:48 GMTSlot Other Front BackSlot Type Slot Card CardLast Command: delyred 2diagbus (diagnose failed IGX bus)
Diagnose a failed IGX Muxbus or IGX cell bus. This command runs detailed diagnostics to isolate Muxbus problems to a failed card or bus. It is used when a minor alarm is indicated and displaying the alarm (dspalms) screen indicates the message "bus needs diagnosis."
This command can be run only locally with a terminal connected directly to the Control port or remotely from a modem connection. It can not be executed through a virtual terminal (VT) command or when the node's Control port is configured for Cisco WAN Manager mode.
Caution
To fully isolate the failure might require manual removal of cards, including controller cards and so forth. For this reason, the command may not be executed over a Virtual Terminal connection.
If the test is successful, and no problems found, the system displays:
Both buses are OK
Otherwise, the system displays various messages to the operator for additional steps to perform in isolating the problem. These messages depend on the results of the diagnostics testing.
Syntax
diagbus
Attributes
dncd (down a card)
Downs (deactivates) a card. When you down a card, it is no longer available as a node resource. You should down a card before you remove it from a card cage. Before it actually downs an active card, the node determines if a standby card is available. If no standby card is present, the node gives you an opportunity to abort the command. If a standby card of the same type is available and you execute dncd, the standby card is activated. If no standby card is available and you execute the command, a major alarm results. To activate a downed card, use the upcd command.
Note
You cannot down a control card (NPM or BCC). Use switchcc for control cards.
If the A-bit Notifications on LMI/ILMI Interface feature is enabled (with cnfnodeparm), after downing the trunk, the master node deroutes the connections or condition the connections due to path fail.
Syntax
dncd <slot number>
Parameters
Attributes
Related Commands
dspcds, resetcd, upcd
Example
Down the card in slot 9.
dncd 9
sw180 TN Cisco IGX 8420 9.3.g0 Oct. 20 2000 09:14 GMTFrontCard BackCard FrontCard BackCardType Rev Type Rev Status Type Rev Type Rev Status1 NPM BVS Standby 9 FRM KSB FRI-T1 AL Down2 NPM BWS Active 10 Empty universal backplane3 Empty universal backplane 11 Empty universal backplane4 UXM CD23 T3 AA Active 12 URM AA11 2FE2V EW Active5 UXM CA23 OC3 AD Active 13 LDM CK03 232-8 AJ Standby-T6 FRM DHZ FRI-V35 BD Standby 14 URM AA13 2FE2V P03 Active7 Empty universal backplane 15 URM AA12 2FE2V EW Active8 Empty 16 NTM FHF T1 AL ActiveLast Command: dncd 9dncon (down connection)
Deactivates (downs) a connection, bundle of connections, a connection group or all connection in a COS or COS range. The dncon command temporarily removes one or more connections from the network. This command is useful for temporarily removing voice connections when additional bandwidth is necessary for other types of connections.
Connections can be downed immediately or with courtesy. Even with immediate downing, a prompt appears that requests confirmation. With courtesy downing, the system waits until the connection is on-hook before downing the connection.
Courtesy downing is possible only if the on-hook status has been configured by using the cnfvchtp command. The upcon command reactivates the voice connections. The up/down status of the voice connections appears in the "State" field of the dspcons screen.
Syntax
dncon {<group | local_chan(s)> | COS <cos_range>} {i | c}
Parameters
Display Fields
Attributes
Related Commands
upcon
Example
Down connection 14.1 with courtesy.
dncon 14.1 c
Example
Down connection 14.1 immediately.
dncon 14.1 i
Example
Courtesy down on-hook connections network-wide with COS 4 through 8. This command marks all connections that may be courtesy downed at one time and does not monitor new connections or those that later fit the COS.
dncon cos 4-8 c
Example
Immediately down connection 3.1.100.
dncon 3.1.100 i
pubsigx1 TN SuperUser IGX 32 9.3 Apr. 13 2000 16:51 GMTLocal Remote RemoteChannel NodeName Channel State Type Compress Code COS3.1.100 pubsigx1 3.2.200 Ok fr3.2.200 pubsigx1 3.1.100 Ok frThis Command: dncon 3.1.100 iDown these connections (y/n)?Example
Immediately down all connections network-wide with COS 4 through 8. This command executes once, so if individual connections are subsequently upped or new connections added in this COS range, they remain up.
dncon cos 4-8 i
dnln (down line)
Deactivates ("downs") a line. After dnln executes, the line no longer generates framing, and no statistics are gathered. (Alias: the dncln command is identical.)
Before you deactivate a line, use delcon to remove all connections on the line and use dnport to deactivate the port associated with the line.
The dnln command is also used to deactivate an IMA line on the IGX only. As with the other lines, you must remove all connections on the IMA line (delcon or delcongrp), then deactivate the port by using the dnport command. You then can deactivate the line by using dnln.
For the BPX: before you can down a line, all ports must be detected by using the delport command. Downing will not remove the port.
Syntax
dnln <[slot.] [line number]>
Parameters
Attributes
Related Commands
upcln, dsplns, dsptsmap
Example
Deactivate line 5.1 (the primary link for an IMA line). After this command executes, the system displays the status of the line using the same information as dsplns displays.
dnln 5.1
sw225 TRM StrataCom IGX 8420 9.3.a6 Mar. 10 2000 05:54GMTLine Type Current Line Alarm Status8.1 T1/24 Clear - OK9 E1/30 Clear - OKLast Command: dnln 5.1dnport (down port)
Deactivates (or downs) the specified port (Frame Relay, ASI, BXM, virtual, or physical port). Before downing a port, you must remove all connections from the port (see delcon definition).
Syntax
dnport <slot.port>[.<vport>]
For UFM-U, FRM, or FRP:
dnport <slot.port>For UFM-C:
dnport <slot.port> <line.ds0_range>Parameters
Attributes
Related Commands
cnfport, dspport, upport, addport, delport, cnffrport, dspfrport, upfrport
Example
Down port 3 on the BXM card in slot 11.
dnport 11.3
sw53 TN Cisco BPX 8620 9.3.m0 Dec. 19 2000 13:04 GMTPort: 11.3 [INACTIVE] Bandwidth/AR BW: 353208/353208Interface: LM-BXM CAC Override: EnabledVPI Range: 0 - 255 CAC Reserve: 0Type: UNI %Util Use: DisabledShift: SHIFT ON HCF (Normal Operation)SIG Queue Depth: 640 Port Load: 0 %Protocol: NONE Protocol by Card: NoLast Command: dnport 11.3Example
Down Frame Relay port 9.2.
dnport 9.2
sw108 VT Cisco IGX 8420 9.3.q2 Dec. 20 2000 12:56 GMTPort: 9.2 [INACTIVE]Interface: V35 DCE Configured Clock: 256 KbpsClocking: Normal Measured Rx Clock: 0 KbpsPort ID 0 Min Flags / Frames 1Port Queue Depth 65535 OAM Pkt Threshold 3 pktsECN Queue Threshold 65535 T391 Link Intg Timer 10 secDE Threshold 100 % N391 Full Status Poll 6 cylSignalling Protocol None EFCI Mapping Enabled NoAsynchronous Status No CLLM Enabled/Tx Timer No/ 0 msecT392 Polling Verif Timer 15 IDE to DE Mapping YesN392 Error Threshold 3 Interface Control TemplateN393 Monitored Events Count 4 Lead CTS DSR DCDCommunicate Priority No State ON ON ONUpper/Lower RNR Thresh 75%/ 25%Last Command: dnport 9.2dntrk (down trunk)
Downs a trunk, after which it no longer carries framing or statistics. Before you can down a trunk by using dntrk, you must remove it from the network by using deltrk (or delshelf in a tiered network).
Syntax
dntrk <slot.port>[.vtrk]
(No space exists between the port number and the "." for the virtual trunk specification.)
Parameters
slot.port
Specifies the physical trunk.
vtrk
Specifies a virtual trunk number (applies to BNI only).
Range (T3/E3): 1-32
Range (OC-3) 1-11
Attributes
Related Commands
addtrk, deltrk, uptrk, dsptrks
Example (IGX)
Deactivate trunk 3.4.
dntrk 3.4
sw108 VT Cisco IGX 8420 9.3.q2 Dec. 19 2000 12:17 GMTTRK Type Current Line Alarm Status Other End4.2 OC3 Clear - OK sw180/5.14.4 OC3 Clear - OK sw53/11.214 T1/24 Clear - OK sw180/8Last Command: dntrk 3.4dport (display port)
Display port Qbin information.
Syntax
dport <slot.port>[.<vport>] qbn | *
Parameters
<slot.port>
Specifies the slot number of the card and the physical port.
[.<vport>]
Optionally specifies a virtual port number. BXM card only.
Range: 1-31
Attributes
Related Commands
addport, dspportq, cnfportq
Example
Display Qbin 1 database information for port 11 on BXM card 1.
dport 11.1 1
sw53 VT Cisco BPX 8620 9.3.m0 Dec. 19 2000 11:05 GMTQbin Database 11.1 on BXM qbin 1algorithm 3depth 20000clp hi 80clp lo 60efci 20vc shaping DisabledBW INC Cells 200BW INC Pages 1Last Command: dport 11.1 1Example
Display Qbin summary information for port 11.1 on a BXM card.
dport 11.1 *
sw53 VT Cisco BPX 8620 9.3.m0 Dec. 19 2000 11:06 GMTQbin Bandwidth Database 11.1 on BXMQbin Bandwidth Increment Qbin Bandwidth Increment0 50 1 8 0 01 200 1 9 0 02 50 1 10 0 03 0 0 11 0 04 0 0 12 0 05 0 0 13 0 06 0 0 14 0 07 0 0 15 0 0Last Command: dport 11.1 *drtop (display route op table)
Displays the routing table from the local node to each connected remote node.
The drtop command displays the routing table from the local node to each remote node to which it connects. It shows how NPM/B.C. traffic is routed to other nodes in the network. Use drtop to find which trunks are used to send control cells or packets to other nodes.
The display includes remote node name, number of hops to the remote node, the trunks used, and number of satellite hops if any, and the number of unused DS0s (open space), if any, on the route.
Syntax
drtop
Attributes
Related Commands
dsptrkcons
Example
drtop
pubsipx2 VT SuperUser IGX 8430 9.3 Apr. 13 2000 02:27 GMTNode Number Node Name Hops To Via Trk SAT Hops No HP Hops Open Space1 npubsbpx1 2 6 0 0 32 npubsigx1 3 6 0 0 33 npubsigx2 0 0 0 0 05 npubsigx1 1 6 0 0 247 npubsigx3 2 6 0 0 24Last Command: drtopNext Command:dspabortlog (display abort log)
Displays the abort errors log. The log contains up to six entries. When the log is full, additional aborts overwrite the oldest entries.
Log contains only fatal entries. The log for software errors (dspswlog command) contains only non-fatal entries.
A lighted icon "AB" at the bottom of the command line interface indicates that a software abort has been logged. Not related to the command, but also displayed at the bottom of the command line interface, the "CD" icon indicates a card or hardware error, and the "SW" icon indicates a software error.
Syntax
dspabortlog [<d> | <number> | <c> ]
Parameters
Display Fields
Related Commands
clrswlog, dspswlog, clrabortlog
Attributes
Example
Displays a detailed log for abort number 1.
dspabortlog 1
sw150 TRM StrataCom IGX 8420 9.3.0L Feb. 2 2000 12:35 GMTActive Control Card's Software LogNo. Type Number Data(Hex) PC(Hex) PROC SwRev Date Time1. Abort 1000001 00000000 301EAED2 TN_2 9.3.0L 02/02/00 11:09:12SSP 306B1310 10 00 30 28 F8 C2 70 08 30 6B 06 40 00 81 00 81 ..0(..p.0k.@....SSP 306B1320 00 01 00 81 30 53 55 E8 30 6B 06 6C 00 00 00 0C ....0SU.0k.l....USP 306B066C 00 00 00 00 00 00 00 01 00 00 00 04 31 5A B7 7C ............1Z.|USP 306B067C 30 53 D6 F8 31 5A DE 28 00 00 02 40 30 53 D6 F8 0S..1Z.(...@0S..USP 306B068C 00 00 00 4F 30 52 1A 56 00 00 00 01 00 00 00 01 ...O0R.V........USP 306B069C 30 6B 07 34 30 52 46 50 00 00 00 01 31 5A D1 64 0k.40RFP....1Z.dUSP 306B06AC 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................USP 306B06BC 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................USP 306B06CC 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................USP 306B06DC 00 0D 00 00 00 00 00 00 31 5A B7 7C 00 00 00 01 ........1Z.|....Last Command: dspabortlog 1dspalms (display current node alarms)
Displays major and minor alarms throughout the network and specific alarms at the local node. The dspalms command displays:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The URM is supported on the IGX 8400 with Release 9.3.20. The URM provides IOS-based voice support and basic routing functions. It consists of an embedded UXM with one internal ATM port and an embedded IOS-based router. The internal ATM port is the communication bridge between the embedded router and switch software.
When the router is not operational (in other words, it cannot route packets among its interfaces, including the internal ATM interface), switch software generates a minor alarm and fails all connections that terminate on the internal port. When an embedded router is not operational, dspalms shows the URM slot number and reports the router status as unavailable (IOS field). A "Minor Alarm" is also displayed in the bottom right corner of the dspalms screen.
For more details on each type of alarm, use the "display" command associated with each failed item. Table 4-2 shows the display commands that show error information.
Syntax
dspalms
Attributes
Related Commands
dspcds, dsplns, dspcons, dsplog, dspnw, dsptrks, dsppwr, dsprtrslot, dsprtrslots
Example (BPX)
Display a summary of all alarms affecting the BPX node.
dspalms
sw167 TN Cisco BPX 8620 9.3.2Q Dec. 13 2000 14:17 PSTAlarm summary (Configured alarm slots: None)Connections Failed: NoneTRK Alarms: NoneLine Alarms: NoneCards Failed: NoneSlots Alarmed: NoneMissing Cards: NoneRemote Node Alarms: 1 MinorAPS Alarms: NoneInterface Shelf Alarms: 1 MinorASM Alarms: NoneLast Command: dspalmsExample
Display APS alarms.
dspalms
alexa TRM genre BPX 8620 9.3 Apr. 13 2000 16:35 PDTAlarm summary (Configured alarm slots: None)Connections Failed: NoneTRK Alarms: NoneLine Alarms: NoneCards Failed: NoneSlots Alarmed: 1 MajorMissing Cards: 1Remote Node Alarms: 1 MinorAPS Alarms: 1 MinorInterface Shelf Alarms: NoneASM Alarms: NoneLast Command: dspalmsExample (IGX)
Display the current alarms on an IGX node.
dspalms
sw150 TN Cisco IGX 8420 9.3.2R Dec. 14 2000 09:23 PSTAlarm summary (Configured alarm slots: None)Connections Failed: NoneTRK Alarms: NoneCircuit Line Alarms: NonePhysical Line Alarms: NoneCards Failed: 2Missing Cards: NoneRemote Node Alarms: 1 Unreachable, 2 Majors, 5 MinorsInterface Shelf Alarms: NoneFastPAD/Access Dev Alms: NoneLast Command: dspalmsNext Command:MAJOR ALARMExample
Display the current alarms on an IGX node with a Universal Routing Module (URM). Check the operational status of the embedded IOS-based router. When the router is not operational, the IOS field shows the router as unavailable and reports the URM slot number. A "Minor Alarm" is also displayed when the router is not operational.
dspalms
sw190 TRM Cisco IGX 8420 9.3.e8 Oct. 4 2000 10:38 GMTAlarm summary (Configured alarm slots:None)Connections Failed: NoneTRK Alarms: NoneCircuit Line Alarms: NonePhysical Line Alarms: NoneCards Failed: NoneMissing Cards: NoneRemote Node Alarms: NoneIOS Unavailable in 1 slotInterface Shelf Alarms: NoneFastPAD/Access Dev Alms: NoneLast Command:dspalmsNext Command:Minor Alarmdspapsln (display APS lines)
The dspapsln command displays the currently configured APS lines and their status.
Syntax
dspapsln
Attributes
Related Commands
addapsln, delapsln, cnfapsln, cnfapsln, dspapsln, dsplog, dspalms
Example
Display all the currently configured APS lines and their status.
dspapsln
alexa TRM genre BPX 8600 9.3 Apr. 13 2000 16:25 PDTActv Active Line Standby Line Current APS Last UserWork/Protect Line Alarm Status Alarm Status Alarm Status Switch Req2.1 3.1 PROT OK OK Loss of Sig(RED) Clear5.1 5.2 WORK OK LOS LOS Lockout6.3 6.4 NONE Deactivated APS Deactivated10.1 11.1 PROT OK OK Standard Mismatch ClearCommand: dspapslnExample
Display currently configured APS lines and their status.
dspapsln
sw117 TRM genre BPX 8620 9.3 Apr. 13 2000 16:25 PDTWork/Protect Actv Active Line Standby Line Current APS Last User(Work 1/Work 2) Line Alarm Status Alarm Status Alarm Status Switch Req2.2 3.2 WORK Loss of Sig (RED) Remote (YEL) Remote (YEL) ClearCommand: dspapslndspasich (display ASI channel routing entry)
Displays the ATM channel routing entries for an ASI card.
Syntax
dspasich <line> <channel>
Parameters
<line>
Specifies the line in the format slot.port.
<channel>
Specifies the channel in the format vpi.vci.
Attributes
Example: ASI Channel Routing Entry
dspasich 5.1 1 N
pubsbpx1 VT SuperUser BPX 15 9.3 Apr. 13 2000 21:09 GMTASI Channel Configuration Query & DisplaySlot.port.lcn:5.1.1Status: Added BF hdr: 4145 9002 8012 0501 8640 0000 2DEB[00] BF tp: 4 [11] VCI: 00000064 [22] UPC CDV: 0 [33] FST up: 0[01] Pri SDA: 5 [12] Con tp: VC [23] UPC CIR: 500 [34] FST dn: 0[02] Dst Prt: 1 [13] Rmt tp: ASI [24] UPC CBS: 1000 [35] FST fdn: 0[03] Dst lcn: 2 [14] Srv tp: VBR [25] UPC IBS: 0 [36] FST rmx: 0[04] BCF tp: 0 [15] Gen AIS: N [26] UPC MFS: 200 [37] Q max:64000[05] Qbin#: 12 [16] Mcst: 0 [27] CLP enb: Y [38] EFCI: 100[06] BF VPI: 64 [17] Mc grp: 1 [28] FST enb: N [39] CLP hi: 100[07] BF VCI: 0 [18] & msk: 0000000F [29] FST MIR: 500 [40] CLP lo: 100[08] Pl Cls: 0 [19] | msk: 06400640 [30] FST PIR: 500 [41] BCM: N[09] Rmt lp: N [20] Prt QBN: 2 [31] FST QIR: 500 [42] Inhibit:N[10] VPI: 00000064 [21] UPC GCR: 0 [32] QIR TO: 0 [43] UPC enb:YLast Command: dspasich 5.1 1 NNext Command:dspasm (display ASM card)
Displays BPX node alarms that, when active, produce an external alarm output (relay closure). These alarms are associated with powering and cooling the node as well as a statistics count.
For example, a minor alarm is generated when a fan speed drops below 2000 rpm. Because the single ASM card is always located in slot 15, you do not need to enter a card slot for this command. To configure the ASM alarms, use cnfasm (a SuperUser command).
Syntax
dspasm
Attributes
Related Commands
cnfasm
Example
Display the ASM card parameters.
dspasm
D1.jea TRM SuperUser BPX 8620 9.3 Apr. 13 2000 12:24 GMTASM Status: Active ASM AlarmsStatistics count: 7 Fan #1 RPM out of rangeStatistics timeouts: 0 Fan #2 RPM out of rangeCabinet temperature: 21 C Fan #3 RPM out of rangePower voltage A/B: 0.0 / 0.0 VPSU Ins Type Rev SerNum FailureA N N/A N/A N/A N/AB N N/A N/A N/A N/AFAN 1 2 30000 0000 0000 RPMLast Command: dspasmNext Command:dspatmcls (display ATM connection class)
Displays the current parameters for an ATM connection class template. There are ten number classes. The parameters and the values for each varies with the connection type (CBR, VBR, ABR, and ATFR).
Syntax
dspatmcls <class number>
Parameters
class number
Specifies the class whose current parameters you want to see.
Range: 1-10
Attributes
Related Commands
addcon, cnfatmcls, dspcls, cnfcls, dspcon, dspcons
Example
Display the parameters for configuration class 1.
dspatmcls 1
night TN SuperUser BPX 8620 9.3 Apr. 13 2000 13:22 GMTATM Connection ClassesClass: 1Type: VBRUPC SCR IBS MBS ABR PCR ABR PCRy 500/500 10/10 1000/1000 - 500/500 -/-ICR ICR TO Rate Up Rate Dn Rate FastDn Max Adjust CDVT[in cells]-/- - - - - - 64000/64000EFCI % Util FGCRA MFS CLP CLP Hi CLP Lo BCM100/100 100/100 n/n -/- y 100/100 100/100 n/nDescription: "Default VBR 500"Last Command: dspatmcls 1Next Command:Example
Display the parameters for configuration class 1.
dspatmcls 1
night TN SuperUser BPX 8620 9.3 Apr. 13 2000 13:22 GMTATM Connection ClassesClass: 3 Type: rt-VBRPCR(0+1) %Util CDVT(0+1) AAL5 FBTC SCR2000/2000 100/100 10000/10000 n 2000/2000MBS Policing1000/1000 3Description: "Default rt-VBR 2000"_____________________________________________Class: 4 Type: rt-VBRPCR(0+1) %Util CDVT(0+1) AAL5 FBTC SCR8000/8000 100/100 10000/10000 n 8000/8000MBS Policing1000/1000 3Description: "Default nrt-VBR 8000"Last Command: dspatmcls 1Next Command:dspbmpparm (display priority bumping parameters)
Displays the priority bumping parameters.
Syntax
dspbmpparm
Parameters
Attributes
Related Commands
cnfbmpparm
Example
Use dspbmpparm to view the priority bumping parameters. Priority bumping for the whole network is shown at the top of the display, and then at the bottom for a specific node.
igxr2 TN StrataCom IGX 8420 9.3.0K Jan. 26 2000 15:19 PDT1 Priority Bumping Enabled [ YES]2 Priority Bumping Bundle [ 10] (D)3 Priority Bumping Bands:Bumping Band 1 [ 2] (D)Bumping Band 2 [ 4] (D)Bumping Band 3 [ 6] (D)Bumping Band 4 [ 8] (D)Bumping Band 5 [ 10] (D)Bumping Band 6 [ 12] (D)Bumping Band 7 [ 14] (D)Priority Bumping Active on this node [ YES]Number of Priority Bumping Bands [ 7] (D)Last Command: dspbmpparmbpx1 TN StrataCom BPX 8620 9.3.0K Jan. 26 2000 14:20 PST1 Priority Bumping Enabled [ YES]2 Priority Bumping Bundle [ 10] (D)3 Priority Bumping Bands:Bumping Band 1 [ 2] (D)Bumping Band 2 [ 4] (D)Bumping Band 3 [ 6] (D)Bumping Band 4 [ 8] (D)Bumping Band 5 [ 10] (D)Bumping Band 6 [ 12] (D)Bumping Band 7 [ 14] (D)Priority Bumping Active on this node [ NO]Number of Priority Bumping Bands [ 0] (D)Last Command: dspbmpparmdspbmpstats (display priority bumping statistics)
Displays priority bumping operational statistics for the priority bumping feature.
Syntax
dspbmpstats
Attributes
Related Commands
dspbmpparm, cnfbmpparm, dsprrst s, rrtinf
Display Fields
Example (BPX)
dspbmpstats
sw67 TN StrataCom BPX 8620 9.3.0L Jan. 28 2000 18:57 PSTPB Routing StatisticLatest bumping band - Latest bumped band -Hwm bumping band - Lwm bumped band -Latest # bumping conns/req 0 Latest # bumped conns/req 0Hwm # bumping conns/req 0 Hwm # bumped conns/req 0Accum # bumping conns 0 Accum # bumped Lcons 0Avg # bumping conns/req 0.00 Accum # bumped VLcons 0Last Command: dspbmpstatsdspbob (display breakout box)
Shows the current state of all inputs from user equipment to the node the state of all outputs from the node to the user equipment. The display is real-time and updated at a user-specified interval. The display refreshes at the designated interval until the Delete key is pressed or until it times out.
See the cnfict description for information on configuring data interfaces. When used with Frame Relay T1/E1 applications, dspbob displays the message "This FRP does not support V.35 ports."
Displaying Signal Status for Port Concentrator Ports
If an FRM-2 or FRP-2 card connects to a Port Concentrator Shelf (PCS), you can specify up to 44 ports by using the port parameter. In this case, dspbob displays the signal status for ports on the PCS. The PCS relays any changes in signal states to the FRM-2 or FRP-2, so a slight delay occurs when signals are updated.
When used for PCS ports, dspbob has an optional parameter measuring port clock speed. Selection of this parameter temporarily interrupts all traffic on the logical port. The events that take place upon input of this parameter are:
1.
2.
3.
Syntax
dspbob <slot><port> [interval] [(measure clock speed) y | n ]
Parameters
Attributes
Related Commands
cnfict, dspcon, dspict
Example
See the breakout box display for channel 5.1.
dspbob 5.1
alpha TRM YourID:1 IGX 8420 9.3 Apr. 13 2000 11:29 PSTPort: 5.1Interface: V35 DCEClocking: Normal (255999 Baud)Inputs from User Equipment Outputs to User EquipmentLead Pin State Lead Pin State Lead Pin State Lead Pin StateRTS C Off CTS D OnDTR H Off DSR E OnTxD P/S Idle DCD F OffTT U/W Unused RI J OffTM K OffRxD R/T IdleRxC V/X ActiveTxC Y/a ActiveThis Command: dspbob 5.1Hit DEL key to quit:Example
See the breakout box display for Frame Relay connections.
dspbob 9.1
alpha TRM YourID:1 IGX 8420 9.3 Apr. 13 2000 11:29 PSTPort: 9.1Interface: FRI-V35 DTEClocking: NormalInputs from User Equipment Outputs to User EquipmentLead Pin State Lead Pin State Lead Pin State Lead Pin StateCTS D Off RTS C OnDSR E Off DTR H OnDCD F Off LT L Off(TM) n Off (RLB) N OffThis Command: dspbob 9.1Hit DEL key to quit:dspbpnv (display backplane NOVRAM)
Issue the dspbpnv command to see the NOVRAM setting for the backplane. For some operations, you must verify if the node has the new backplane or the old backplane. For example, in order for the BPX 8600 to operate at 19.2 Gbps with the BCC-4V, it must have the NOVRAM Word #2 set to 0001 (which indicates that the backplane version is new). If it instead has the NOVRAM Word# set to 0000 (indicating that the backplane version is old) the switch cannot run with a 19.2 Gbps peak throughput. If you visually verify that the backplane is a 19.2 Gbps backplane (see note below), but the backplane NOVRAM Word #2 has not been set to 0001, then issue the cnfbpnv command to program the NOVRAM.
Note
The following table details the bit fields for the BCC Backplane NOVRAM format. The display in the field Word 2 describes the backplane type.
Syntax
dspbpnv
Attributes
Related Commands
cnfbpnv
Example (BPX)
View the NOVRAM settings on a BPX 8620.
dspbpnv
sw217 TN Cisco BPX 8620 9.3.x5 June 11 2001 14:34 GMTBackPlane NOVRAM----------------WORD 0: 0x0096 WORD 1: 0x0065WORD 2: 0x0000 WORD 3: 0x3232WORD 4: 0x3037 WORD 5: 0x3632WORD 6: 0x0000 WORD 7: 0x0000WORD 8: 0x0000 WORD 9: 0x0000WORD 10: 0x0000 WORD 11: 0x0000WORD 12: 0x0000 WORD 13: 0x0000WORD 14: 0x0000 WORD 15: 0x9997Last Command: dspbpnv
dspbusbw (display cell bus bandwidth for UXM cards)
Displays the amount of bandwidth allocated on the cell bus on an IGX node. By default, the system allocates enough bus bandwidth for one OC-3 when the first line is upped by using the upln command. If there is not enough allocated cell bus bandwidth, the line is not upped. Cell bus bandwidth must be allocated before adding connections on the UXM card.
Syntax
dspbusbw <slot> [u]
Parameters
Display Fields
Attributes
Related Commands
cnfbusbw
Example
Display the amount of bandwidth allocated on the cell bus on the UXM card in slot 6 of the IGX node.
dspbusbw 6
Get updated bandwidth info from card (Y/N)? nsw199 TN StrataCom IGX 16 9.3 Apr. 13 2000 17:52 GMT1\NBus Bandwidth Usage for UXM card in slot 6 Last Updated on 04/07/98 12:03:00FPkts/sec Cells/sec UBUsMinimum Reqd Bandwidth: 0 0 0Average Used Bandwidth: 0 0 0Peak Used Bandwidth: 0 0 0Maximum Port Bandwidth: - 10866 3Allocated Bandwidth: 8(Cell Only): - 32000(Cell+Fpkt): 16000 24000(Fpkts / 2 + Cells) <= 32000Reserved Bandwidth: - 4000 1Last Command: dspbusbw 6Next Command: dspbusbw 6Get updated bandwidth info from card (Y/N)? ysw199 TN StrataCom IGX 16 9.3 Apr. 13 2000 17:53 GMT1\NBus Bandwidth Usage for UXM card in slot 6 Last Updated on 04/09/98 17:53:22FPkts/sec Cells/sec UBUsMinimum Reqd Bandwidth: 0 0 0Average Used Bandwidth: 0 0 0Peak Used Bandwidth: 0 0 0Maximum Port Bandwidth: - 10866 3Allocated Bandwidth: 8(Cell Only): - 32000(Cell+Fpkt): 16000 24000(Fpkts / 2 + Cells) <= 32000Reserved Bandwidth: - 4000 1Last Command: dspbusbw 6dspbuses (display bus status)
Displays the available Muxbus or cell bus bandwidth. The display does not dynamically receive updates and is therefore a snapshot. The dspbuses command lists the dedicated and pooled bandwidth units as well as the status of the available Muxbus.
As a safeguard against bus failure, each node is equipped with redundant System Buses: Bus A and Bus B. Either bus can be configured as the active bus with the other bus as standby. Use the cnfbus command to switch the active bus.
Each System Bus contains these buses:
•
•
•
•
In addition to showing which System Bus is active and which is standby, the dspbuses command also shows which sub-bus needs diagnostics or has failed. Bus status is displayed at the bottom of the screen. Table 4-3 shows the possible status displays and their meaning.
The remaining cell bus bandwidth available to assign to cards and circuits is displayed. This is primarily used when configuring the AIT card on the IGX node. You can assign CELLBUS bandwidth for the IGX node.
Available bandwidth falls into two categories:
•
Dedicated bandwidth is reserved by the system for specific purposes, such as Statistical Reserve for PCC traffic.•
Pooled bandwidth can be assigned to any use but primarily is used for an ATM trunk.Cell bus bandwidth is assigned in quantities of "switches," "slices," and "circuits" and the available bandwidth is displayed in three rows accordingly. A single DS0 circuit occupies 333 packets per second (pps) of cell bus bandwidth, a "slice" of bandwidth is equivalent to three DS0 circuits for a total of 1000 pps. A switch is eight slices for a total of 8000 packets/second of bus bandwidth.
In a newly installed node with no cards and no circuits installed, the total bus bandwidth that is available to be assigned is listed in the right column of the following table, which is the sum of the dedicated and pooled bandwidth. As cards and circuits are added to the node, the available bandwidth decreases accordingly.
Table 4-4 Bandwidth Units and Capacity
switch
8 slices or 8000 pps
20
slice
3 DS0s or 1000 pps
160
DS0
333 pps
480
Syntax
dspbuses
Attributes
Related Commands
cnfbus
Example (BPX)
dspbuses
bpx1 TN SuperUser BPX 15 9.3 Apr. 13 2000 13:22 GMTBus StatusBus A (slot 7): Active - OKBus B (slot 8): Standby - OKLast Command: dspbusesNext Command:Example (IGX)
dspbuses
sw197 TN SuperUser IGX 8420 9.3 Apr. 13 2000 04:10 GMTBus InfoBus Bandwidth usage in Fastpackets/second (Snapshot)Allocated = 86000 ( 8%)Available = 1082000 (92%)-----------Bus A: Active - OKBus B: Standby - OKLast Command: dspbusesExample (IGX)
Display status and bandwidth available. The status of Bus A and Bus B is displayed. In this example, both buses are OK and B is the active control bus (normal operation is for bus A to be the active bus).
dspbuses
alpha TRM YourID:1 IGX 8420 9.3 Apr. 13 2000 13:34 PSTBus InfoAvailable MUXBUS bandwidth (snapshot)Dedicated Pooled Units--------- ------ -----0 13 8000 pkts/sec5 104 1000 pkts/sec22 312 ds0 circuitsBus Status-----------Bus A: Standby - OKBus B: Active - OKLast Command: dspbusesNext Command:dspcdstats (display UXM card statistics)
The dspcdstats command displays the collected UXM card statistics for the selected node slot.
Syntax
dspcdstats <slot number>
Parameters
Attributes
Related Commands
cnfslotstats, dspsloterrs (for BXM)
Example (IGX)
Display UXM Card Statistics
dspcdstats 9
bolger TN Cisco IGX 8430 9.3.3q May 25 2001 12:23 PSTSlot 9Collection Time: 1 day(s) 03:15:51 Clrd: Date/Time Not SetType CountQBIN: Ingress Cells Rcv from ln 22QBIN: Ingress Cells Tx to net 22QBIN: Ingress Cells discarded 0QBIN: Ingress FPs Rcv from ln 68013QBIN: Ingress FPs Tx to net 68013QBIN: Ingress FPs discarded 0This Command: dspcdstats 9Example (IGX) Field Descriptions
dspcbause (display CBA block usage)
Queries the specified slot and displays information about the CBA blocks. While running this command, it periodically queries the card and the display continuously updates the CBA parameters, showing block usage among AutoRoute and VSI.
To display a summary of CBA usage on all active UXMs on the node, enter dspcbause with no parameters.
To display CBA usage on a specific active UXM card, enter dspcbause with the slot number parameter.
Syntax
dspcbause [slot_no] [interval]
Parameters
[slot_no]
Optionally specifies the slot number of a particular UXM card.
[interval]
Optionally specifies the interval in seconds. Default: 10 seconds.
Display Fields
Attributes
Example
dspcbause
Display CBA and CBA block use of Automatic Routing Management and VSI (on a node).
sw188 TRM Cisco IGX 8420 9.3.1c Aug. 17 2000 11:10 PSTVSI CBA allocation summary for all slots :Slot VSI LCNs CBA Blks Actual CBA Blksto be alloced alloced4 200 7 75 2000 63 63Last Command: dspcbauseNext Command:Example
Display CBA and CBA block use among AutoRoute and VSI (on a slot).
dspcbause 5
sw188 TRM Cisco IGX 8420 9.3.1c Aug. 17 2000 11:11 PSTCBA Usage for slot 5CBA Blocks allocated = 63 CBA Blocks used = 16CBA Block Bitmap:80 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0140 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0200 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 02C0 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0380 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0440 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0500 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 05C0 : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0680 : 0 0 F8 FF 7 0 0 0 0 0 0 0This Command: dspcbause 5Hit DEL key to quit:dspcd (display card)
Displays the status, revision, serial number, and top assembly number of a card. If a back card is present, its type, revision, and serial number appear. The displayed information can vary with different card types and appears on a single-page display.
Syntax
dspcd <slot number>
Parameters
<slot number>
Specifies the slot number of the card for which you wish to see status and identifying information.
Attributes
Related Commands
dncd, dspcds, resetcd, upcd
Example (BPX) BXM-155
Display features supported (Support fields) on the BXM card in slot 2. The front card supports the Neighbor Discovery feature (NbrDisc) and the XLMI protocol (XL). Both the LMI Neighbor Discovery feature and XLMI protocol are required for AR-PNNI links in a hybrid network.
dspcd 1
BPX02 TN Cisco BPX 8620 9.3.3W Aug. 13 2001 11:24 PDTDetailed Card Display for BXM-155 in slot 1Status: ActiveRevision: FA21 Backcard InstalledSerial Number: A66165 Type: LM-BXMTop Asm Number: 80033333 Revision: BBQueue Size: 524280 Serial Number: 770491Supp:8 Pts, OC3, FST, VcShp Top Asm Number:Supp: VT,ChStLv 1,VSI(Lv 3,ITSM) Supp: 8 Pts,OC3,MMF,RedSlot:NOSupp: APS(FW), F4F5Support: LMIv 1,ILMIv 1,NbrDisc,XLSupp: OAMLp,TrfcGen,PPDPolic,OAM-E#Ch:32768,PG[1]:32736,PG[2]:32736PG[1]:1,2,3,4,PG[2]:5,6,7,8,#Sched_Ch:61440 #Total_Ch:61376Type: BXME, revision DXLast Command: dspcd 1
Table 4-6 Display Fields for Example (BPX) BXM-155
BXM Front Card Fields
Status
Displays the status of a card.
Active
Card in use, no failure detected.
Active—F
Card in use, failure detected.
Active—T
Card active, test in progress.
Active—F-T
Card active, minor failure detected, test in progress.
Standby
Card idle, no failure.
Standby—F
Card idle, failure detected.
Standby—T
Card idle, test in progress.
Standby—F-T
Card idle, failure detected, test in progress.
Failed
Card failed.
Down
Card downed by user.
Down—F
Card downed, failure detected.
Down—T
Card downed, failure detected, test in progress.
Mismatch
Mismatch between front card and back card.
Update *
Configuration RAM being updated from active control card.
Locked*
Old software version is being maintained in case it is needed.
Dnlding*
Downloading new system software from the active PCC adjacent node from WAN Manager.
Dnldr*
Looking to adjacent nodes or WAN Manager for either software to load or other software needs you have not specifically requested.
Program
Occurs when new firmware is being burned on the card.
Revision
The firmware/hardware version ID.
Serial Number
The serial number of the card.
Top Asm Number
The card's 800-level part number.
Queue Size
The sum of the sizes of the ATM cell queues in one direction. Queue size = size of HP+TS+BDATA+BDATB+CBR+VBR +SIG+ABR queues.
Support or Supp
The features that the card's firmware and hardware supports.
Pts
The number of physical ports supported by card hardware: OC3 | OC12 |T3 | E3
The card type supported
Indicates firmware supports Foresight.
VcShp
Indicates firmware supports VCshaping.
VT
Indicates firmware supports virtual trunks
ChStLv
The multilevel channel statistics level currently programmed 0-3. The statistics level is configured using the command cnfcdparm. Refer to cnfcdparm (configure card parameters), page 3-143 for more information about multilevel channel statistics.
VSI
The VSI attributes supported. Values are:
lv-VSI level supported by firmware. The level is 0, 1, 2, or 3; the level represents the resources supported, i.e. LCNs, VPI, etc.
ITSM-VSI level supported by firmware.
I = ILMI support.
T = topology support.
S = signalling, QBIN support.
M = multiple partition support.
V = VC merge support.
APS
The APS attributes supported. Values are:
APS(FW)-APS is supported by card firmware.
APS(HW1+1)-APS 1+1 is supported by card hardware.
APS(ChHlv)-The number of channels supported by card is halved in order to support APS 1:1.
F4F5
F4 AIS detection on trunks and F4 AIS to F5 AIS mapping on ports is supported by card firmware.
LMIv
LMI version supported by card firmware.
ILMIv
ILMI version supported by card firmware.
NbrDisc
ILMI neighbor discovery is supported by card firmware.
OAMLp
OAM loopback testing is supported by card firmware.
XL
XLMI protocol supported by card firmware.
TrfcGen
Traffic Generation testing is supported by card firmware.
PPDPolic
OAM-E
OAM Ping feature supported by card firmware.
#Ch
The total number of channels supported by all port groups.
PG[1]:8160 PG[2]:8160
The number of channels contained in each port group.
PG[1]:1,2,3,4,
PG[2]:5,6,7,8
The card physical ports.
#Sched_Ch
The number of scheduler channels supported by card.
#Total_Ch
The total number of channels reported by the BXM cards.
BXM Back Card Fields
Type
The type of backcard: LM-BXM, T3-3, E3-3, T3-2, E3-2, SMF, MMF, SMFLR, LMASM, STM1, UTP, STP.
Revision
The hardware version ID.
Serial Number
The serial number of the card.
Top Asm Number
(TAN) The 800-level part number of the card.
Supp
The resources and features this card supports. For example:
8 Pts,OC3,SMF,APS,RedSlot:2
Pts
The number of ports on the backcard
OC3
Supports SONET OC3 with SMF
Supp (cont.)
APS
Supports APS 1:1
RedSlot:<slot number>
If APS 1+1 supported by the backcard, and configured, this field shows the redundant card's slot number. Values are:
??- If APS 1+1 supported by the backcard, but not configured.
NO- If APS 1+1 is not supported by the backcard.
Example (IGX) UXM
Detailed Card Display for UXM card in slot 9.
dspcd 9
sbolger TN Cisco IGX 8430 9.3.3o May 17 2001 17:43 PSTDetailed Card Display for UXM in slot 9Status: Active Front Card Supports:Revision: CD02 Vtrunks, OAMLpbk & TrfcGen, ILMI ver 1,Serial Number: 284344 Neighbor Discovery, SIW, CGW, CellFwd,Top Asm Number: 28216402 Hot Standby, Trfc Shaping, IMA,Backplane Installed ChnStatLvl 1, NumChans = 8000,Backcard Installed NumRCMP = 8191, VSI ver 2, VSI CtrlrType: OC3Revision: ADSerial Number: 258051Top Asm Number: 28226303Ports: 4Line Mode: SMFLast Command: dspcd 9Next Command:
Example (BPX)
Displays Neighbor Discovery support under the Front Card Supports field for a BXM card in slot 13, and VC Merge support, designated by V in:
Supp: VT,ChStLv 1,VSI(Lv 3,ITSMV)
dspcd 13
ssw177 TN Cisco BPX 8620 9.3.c3 May 4 200123:39 GMTDetailed Card Display for BXM-155 in slot 13Status: ActiveRevision: FAL Backcard InstalledSerial Number: A66604 Type: LM-BXMTop Asm Number: 8000309303 Revision: BBQueue Size: 260090 Serial Number: A84438Support: 4 Pts, OC3, FST, VcShp Top Asm Number:Supp: VT,ChStLv 1,VSI(Lv 3,ITSMV) Supp:8 Pts,OC3,MMF,RedSlot:NOSupp: APS(FW)Support: LMIv 1,ILMIv 1,NbrDisc,XLSupport: OAMLp, TrfcGen, PPDPolic#Ch:32768,PG[1]:32736,PG[2]:32736PG[1]:1,2,PG[2]:3,4,#Sched_Ch:61440 #Total_Ch:61376Type: BXME, revision DXdspcderrs (display card errors)
Displays detailed card failure information resulting from card diagnostics testing at the local node.
This command displays a history of card failures associated with a specified slot. If no argument is specified, a summary is displayed, indicating which slots have failures recorded against them. The command displays the results of the self-tests and background tests as well as the total hardware errors.
To clear the card error counters, use the clrcderrs command. To obtain a hard copy of the report, use the prtcderrs command.
Syntax
dspcderrs [<slot>]
Parameters
Attributes
Related Commands
clrcderrs, prtcderrs
Example
Display card errors on the card in slot 11.
dspcderrs 11
sw83 TN SuperUser IGX 8420 9.3 Apr. 13 2000 17:56 PSTAIT in Slot 11 : 176767 Rev AEF Failures Cleared: Apr. 13 2000 11:25:29 PST----------------------------------- Records Cleared: Apr. 13 2000 13:14:03 PSTSelf Test Threshold Counter: 0 Threshold Limit: 300Total Pass: 0 Total Fail: 0 Total Abort: 0First Pass: Last Pass:First Fail: Last Fail:Hardware Error Total Events: 0 Threshold Counter: 0First Event: Last Event:Last Command: dspcderrs 11Next Command:dspcdred (display redundant cards)
The command dspcdred has the same functionality as the command dspyred; therefore, please use the command dspyred. For information about dspyred command usage, refer to dspyred (display Y-cable redundancy).
dspcds (display cards)
Displays the cards in a shelf, front and back, with their type, revision, and status. For front and back card sets, the status field applies to the cards as a set. A "T" opposite a card indicates that it is running a self-test or a background test. An "F" opposite a card indicates that it has failed a test.
If lines or connections have been configured for a slot, but no suitable card is present, the display lists the missing cards at the top of the screen.
If a special backplane is installed or if a card was previously installed, empty slots are identified as "reserved."
For a two-shelf node, the screen initially displays only the upper shelf with a "Continue?" prompt. Typing "y" to the prompt displays the cards in the lower shelf. For an IGX 8410 node, the card information appears in only the left column.
Syntax
dspcds [l]
Parameters
l
Directs the system to display status of the cards on just the lower shelf of an IGX 32 node.
Attributes
Related Commands
dncd, dspcd, resetcd, upcd
Display Cards Update and Status Display Fields
In the preceding messages, an asterisk (*) means an additional status designation for BCC or NPM cards. An "F" flag in the card status indicates that a non-terminal failure was detected. Cards with an "F" status are activated only when necessary (for example, when no other card of that type is available). Cards with a "Failed" status are never activated.
The "reserved for" logic in Release 9.2 reserves the slot for a BXM if SONET APS (Automatic Protection Switching) has been configured on the slot.
To support the Hitless Rebuild feature in Release 9.2, after a switchover has occurred and the standby updates are about to begin, the dspcds command shows the standby processor card as missing temporarily. This is a result of the delay in performing the full rebuild on the standby processor, which is necessary as part of the hitless rebuild sequence.
Following any processor card switchover, the new standby rebuilds, preserving the critical databases needed for a hitless rebuild. When database updates can start, the standby rebuilds again doing a normal standby rebuild. If there is a failure on the new active card that causes it to switch back before updates can start, the card taking over performs a hitless rebuild. Under most conditions, the second switchover is not necessary, and a full rebuild is done on the standby processor. As this process begins, the standby card briefly appears to be missing.
Example (URM on IGX)
Display the status of cards in an IGX node with Universal Router Module (URM) cards.
dspcds
sw175 TN Cisco IGX 8420 9.3.q6 Mar. 9 2000 05:21 GMTMissing Cards: 1 NPMFrontCard BackCard FrontCard BackCardType Rev Type Rev Status Type Rev Type Rev Status1 NPM FMR Active 9 FRM ESX FRI-T1 AL Standby2 Empty reserved for NPM 10 URM BA03 2FE P03 Standby3 Empty 11 URM BA04 2FE P03 Standby-T4 Empty 12 NTM EKJ Empty Standby5 UXM CAA Empty Standby 13 Empty6 URM BA04 Empty Standby 14 Empty7 UXM BDJ E1-IMA AC Standby-T 15 Empty8 Empty 16 URM BA03 2FE P03 StandbyLast Command:dspcdsExample (OC-12 on BPX)
Display status of cards on a BPX node. The two-port BME card with OC-12 interface is in slot 11.
dspcds
sw60 TN SuperUser BPX 15 9.3 Apr. 13 2000 11:36 GMTMissing Cards: 1 BCCFrontCard BackCard FrontCard BackCardType Rev Type Rev Status Type Rev Type Rev Status1 BNI-T3 CCF T3-3 BE Active 9 BNI-155 BDK MMF-2 CM Standby2 Empty 10 Empty3 ASI-T3 BJF T3-2 AA Standby 11 BME-622 K08 11LM-BXM P02AB Active4 ASI-E3 BMJ E3-2 BE Standby 12 ASI-155 BDK MMF-2 AB Standby5 BNI-E3 CMF E3-3 EY Standby 13 Empty6 Empty 14 Empty7 BCC BWF LMBCC AC Active 15 ASM ACA LMASM AC Active8 Empty reserved for CardLast Command: dspcdsdspcftst (display communication fail test pattern)
Displays the test pattern used for the communications fail test.
This test pattern is used to test the controller communication path to a node that does not respond to normal controller traffic. The test pattern defaults to an alternating 8-byte sequence of 00 and FF. Refer to cnfcftst command for other patterns and how to reconfigure this pattern.
Syntax
dspcftst
Attributes
Related Commands
cnfcftst
Example
dspcftst
sw83 TN SuperUser IGX 8420 9.3 Apr. 13 2000 17:57 PSTComm Fail Test Pattern.Byte 0: FF Byte 12: 00 Byte 24: FF Byte 36: 00 Byte 48: FFByte 1: FF Byte 13: 00 Byte 25: FF Byte 37: 00 Byte 49: FFByte 2: FF Byte 14: 00 Byte 26: FF Byte 38: 00 Byte 50: FFByte 3: FF Byte 15: 00 Byte 27: FF Byte 39: 00 Byte 51: FFByte 4: 00 Byte 16: FF Byte 28: 00 Byte 40: FF Byte 52: 00Byte 5: 00 Byte 17: FF Byte 29: 00 Byte 41: FF Byte 53: 00Byte 6: 00 Byte 18: FF Byte 30: 00 Byte 42: FF Byte 54: 00Byte 7: 00 Byte 19: FF Byte 31: 00 Byte 43: FF Byte 55: 00Byte 8: FF Byte 20: 00 Byte 32: FF Byte 44: 00 Byte 56: FFByte 9: FF Byte 21: 00 Byte 33: FF Byte 45: 00 Byte 57: FFByte 10: FF Byte 22: 00 Byte 34: FF Byte 46: 00 Byte 58: FFByte 11: FF Byte 23: 00 Byte 35: FF Byte 47: 00 Byte 59: FFLast Command: dspcftstNext Command:dspchan (display channel configuration)
Displays the configuration of IGX voice channels. This is primarily a debug command that allows you to inspect the data structure defining a channel. Parameters for voice and signaling processing on a CVM voice channel are displayed by this command. Table 4-8 lists the displayed CVM parameters. Many of these parameters are also displayed elsewhere.
Syntax
dspchan <channel>
Parameters
Attributes
Related Commands
cnfcdpparm
CVM Voice Channel Parameters
Example (IGX)
dspchan 7.1
sw83 TN SuperUser IGX 8420 9.3 Apr. 13 2000 18:06 PSTChannel Data Base for CDP card 7 chan. 000000 at address 30BF29ECVC Index -1 Onhk C 4In Loss 0 Onhk D 4Out Loss 0 Dial Type 0Chan Type 1 TX A bit 1Sig. Intg 96 TX B bit 1Xmt. dlay 5 TX C bit 0Smpl dlay 1 TX D bit 1Bk noise 67 RX A bit 1DSI smple 168 RX B bit 1Chan Util 40 RX C bit 0Onhk A 3 RX D bit 1Onhk B 3 Signaling TSP MODEThis Command: dspchan 7.1Continue?sw83 TN SuperUser IGX 8420 9.3 Apr. 13 2000 18:07 PSTChannel Data Base for CDP card 7 chan. 000000 at address 30BF29ECTX CODE 3 iec cancel 0RX CODE 3 iec nlp 1TX SIG 0 iec converg. 1RX SIG 0 iec erl lvl 1CLR CHN 0 iec Hregs. 1SIG RATE 0 iec tone dsbl 1PLY MSBhx 1 adpcm flag 0PLY LSBhx 90In use 0DPU -Last Command: dspchan 7.1Next Command:Example (BPX)
dspchan 11.1
sw53 TN Cisco BPX 8620 9.3.m0 Dec. 12 2000 12:16 GMTChannel Data Base for 11.1 on BXM at address 0x325C48DApcnfg_nm_chans 0 apc_metro 0pcnfg_bandwidth 353208 pcnfg_basis 0pcnfg_frst_indx 0 apc_t1_basis 0pcnfg_chan_cnt 5 apc_nni_port 0pcnfg_loop 0pcnfg_state 1pcnfg_cnfg 1pcnfg_hipri 0pcnfg_com_fail 0pcnfg_ptp_conn 0Last Command: dspchan 11.1dspchcnf (display channel configuration)
Displays configuration details for voice, data, ATM, or Frame Relay channels.
Voice Channels
When you specify a voice channel with dspchcnf, the display shows configuration details for all channels on the specified circuit line starting with the specified channel:
•
•
•
•
•
•
•
Data Channels
The data cards that support this command are the HDM, LDM, UVM, and CVM/CVP cards on the IGX node.
For data connections on the specified card and starting with the specified channel, the dspchcnf command displays configuration details for all channels on the specified data card (CDP, SDP, or LDP) starting with the specified channel:
•
•
•
•
•
•
Frame Relay Channels
The display includes configuration details for all channels on the specified FRP port starting with the specified channel. If you specify a Frame Relay port only with no DLCI, the display includes configuration details for all channels on the Frame Relay port specified. The display also indicates either Cisco parameters or standard Frame Relay parameters where appropriate.
When you specify a Frame Relay channel with dspchcnf, the display shows:
•
•
•
•
•
•
•
•
Syntax
dspchcnf <start_channel>
Parameters
Attributes
Related Commands
cnfdch, cnfchadv, cnfchdfm, cnfchdl, cnfcheia, cnfchgn, cnfchtp, cnfchutl, cnffrcon, cnfchpri
Example (UVM on IGX)
Display the channel configuration of line 7.1.1-24. The card in slot 7 is a UVM.
dpchcnf 7.1.1
sw109 VT cisco IGX 8420 9.3 Apr. 13 2000 18:59 PST% Adaptive Gain (dB) Dial Interface OnHk CondChannels Util Voice Fax In Out Type Type A B C D Crit7.1.1-24 40 Enabled Disabled 0 0 Inband 2W E&M 0 X - - a7.2.1-24 40 Enabled Disabled 0 0 Inband Unconfig ? ? - - aLast Command: dspchcnf 7.1.1Next Command:Example (CVM on IGX)
Show channel configuration of line 13. The card in slot 13 is a CVM.
dspchcnf 13.1
sw150 TN Cisco IGX 8420 9.3.2T Dec. 19 2000 23:32 PST% Adaptive Gain (dB) Dial Interface OnHk CondChannels Util Voice Fax In Out Type Type A B C D Crit13.1-24 60 Enabled - 0 0 Inband Unconfig ? ? - - aLast Command: dspchcnf 13.1Example (Data Channels on IGX)
Show data channels starting at 13.1.
dspchcnf 13.1
sw180 TN Cisco IGX 8420 9.3.o1 Nov. 30 2000 12:15 GMTMaximum EIA % DFM Pattern DFM Idle Code PreAgeChannels Update Rate Util Length Status Suppr (usec)13.1-8 2 100 8 Enabled - 0Last Command: dspchcnf 13.1Example (Frame Relay on IGX)
Show data channels starting at 13.1.
dspchcnf 9.1
sw108 VT Cisco IGX 8420 9.3.q2 Dec. 20 2000 12:29 GMTFrame Relay Channel Configuration Port: 9.1From MIR CIR VCQ Dep PIR Cmax ECNQ Th QIR FST %Utl9.1.918 59.5 59.5 61440 59.5 10 21504 59.5 n 1009.1.919 19.2 19.2 61440 19.2 10 21504 19.2 n 1009.1.920 19.2 19.2 61440 19.2 10 21504 19.2 n 100Last Command: dspchcnf 9.1dspchdlcnf (display channel dial type configurations)
Displays dial type configurations for all channels on a circuit line:
Syntax
dspchdlcnf <start_channel>
Parameters
<start_channel>
Specifies the channel at which the display begins.
For a CDP or CVM, the format is slot.channel.
For a UVM, the format is slot.line.channel.
Attributes
Related Commands
cnfchdl
Display Fields
Example
Display the dial type configuration for all channels beginning with 14.1.
dspchdlcnf 14.1
alpha TRM YourID:1 IGX 8420 9.3 Apr. 13 2000 09:45 PSTChannels Type Sig Delay Min Wink IntDigit Time Playout Delay14.1-24 Inband 12 141 300 -Last Command: dspchdlcnf 14.1Next Command:dspchec (display channel echo canceller configuration)
Displays the integrated echo canceller (IEC) parameters for one or more voice channels. The dspchec command does not apply to CAS or data channels. The specified channels must be on a CDP, CVM, or UVM. See Table 4-4 for what dspchec displays.
Syntax
dspchec <channel>
Parameters
<channel>
Specifies the channel or channels to display.
For a CVM or CDP, the format is slot.channel(s).
For a UVM, the format is slot.line.channel(s).
Attributes
Related Commands
cnfchec
Display Fields
Example
Display the echo canceller configuration for channel 7.1.
dspchec 7.1
pubsipx1 TN cisco IGX 8420 9.3 Apr. 13 2000 06:10 PDTEcho Echo Return Tone Conver- Non-Linear VoiceChannels Cancel Loss (.1 dBs) Disabler gence Processing Tmplt7.1 Enabled High 60 Enabled Enabled Enabled USA7.2-31 Disabled High 60 Enabled Enabled Enabled USALast Command: dspchec 7.1Next Command:dspchstatcnf (display statistics enabled for a channel)
Displays the configuration of enabled statistics for a channel to help debug problems with statistics gathering.
Use the cnfcdparm command to configure the channel statistics level (level 1, 2, or 3) on BXM and UXM cards.
The command output is a list of the connection statistics as set by the cnfchstats command, by Cisco WAN Manager, or by IGX features.
The Owner column identifies who or what set the statistic. If the Owner column shows "Automatic," the node's features set the statistic. If the node name appears under Owner, Cisco WAN Manager set the statistic. If the user name appears under Owner, the cnfchstats command executed from the command line interface set the statistic.
Syntax
dspchstatcnf <channel>
Parameters
<channel>
Specifies the channel whose statistics configuration you want to display.
Attributes
Related Commands
cnfchstats, dspchstathist, cnfcdparm
Example (FR channel)
dspchstatcnf 5.1.100.100
pubsbpx1 VT SuperUser BPX 15 9.3 Apr. 13 2000 23:13 GMTStatistics Enabled on Channel 5.1.100.100Statistic Samples Interval Size Peaks Owner------------------------------------ ------- -------- ---- ----- ----------41) AAL5 Cells Discarded for VCQ Full 1 30 4 NONE TFTP42) Average VCq Depth in Cells 1 30 4 NONE TFTP43) Cells lost due to Rsrc Overflow 1 30 4 NONE TFTP44) Cells discarded for SBIN full 1 30 4 NONE TFTP45) Cells Transmitted with EFCI(Port) 1 30 4 NONE TFTP46) Cells Transmitted(Port) 1 30 4 NONE TFTP47) Cells Received from Network 1 30 4 NONE TFTP48) Cells discarded for QBIN full 1 30 4 NONE TFTP49) Cells discarded when QBIN>CLP 1 30 4 NONE TFTP50) Cells Transmitted with CLP (Port) 1 30 4 NONE TFTP51) BCM Cells Received(Port) 1 30 4 NONE TFTPThis Command: dspchstatcnf 5.1.100.100Continue?dspchstathist (display statistics history for a channel)
Displays a history of statistics configured as enabled for a selected channel. This command is intended for debugging problems with statistics gathering. It displays the data for the number of samples specified in the configuration of the channel statistic. You select a statistic from the list in the dspchstathist display. Specify only an enabled statistic.
You can use the cnfdparm command to configure the channel statistics level on the BXM and UXM cards. Make a note of the statistics types enabled, the collection interval, and owner; you will need this information to obtain the statistics history. Use cnfchstats to enable a statistic if it is not already enabled.
Syntax
dspchstathist <channel> <stat> <owner> <interval>
Parameters
Attributes
Related Commands
cnfchstats, cnfchlevel, dspchstatcnf
Example
A display for channel 6.1 packets transmitted (1 second interval) history.dspchstathist 6.1 7 1 AUTO
gamma TRM SuperUser Rev: 9.3 Apr. 13 2000 13:53 PDTPackets Transmitted on Channel 6.1Interval: 1 Minute(s), Data Size: 4 Byte(s), NO Peaks, Owner: Automatic0 - 1699-1 - 1698-2 - 1698-3 - 1699-4 - 1698-5 - 1698-6 - 1698-7 - 1699-8 - 1697-9 - 1699Last Command: dspchstathist 6.1 7 1 AUTONext Command:dspchstats (display summary statistics for a channel)
Displays summary statistics. This command is intended for debugging problems with statistics gathering. It displays the data for the last five occurrences of the channel statistic.
The multilevel channels statistics feature provides additional levels of channel statistics configuration for the BXM/UXM cards. You can use the cnfcdparm command to configure the channel statistic level on the BXM and UXM cards. For more information see the cnfcdparm command description.
The examples show these statistics categories:
•
•
•
•
•
•
Syntax
dspchstats <channel> [interval]
Parameters
Attributes
Related Commands
cnfchstats, dspchstatcnf
Display Fields (Frame Relay Channel Statistics)
Table 4-10 displays 35 statistics are available for each Frame Relay PVC channel. Note that the statistic field name listed may be slightly different from the field name on the dspchstats screen.
Example (IGX)
Display the channel statistics for connection 14.1.1.
The system response shows these statistics categories:
•
•
•
•
•
•
dspchstats 14.1.1
igxr03 VT Cisco IGX 8430 9.3.2V Jan. 18 2001 13:07 PSTChannel Statistics: 14.1.1 Cleared: Jan. 15 2001 09:06 (|)MIR: 64/64 kbps Collection Time: 3 day(s) 04:09:55 Corrupted: NOFrames Avg Size Avg Util Packets Avg(bytes) (fps) (%) (pps)From Port: 0 0 0 0To Network: 0 0 0 0 0 0Discarded: 0 0 0 0From Network: 0 0 0 0 0 0To Port: 0 0 0 0Discarded: 0 0 0 0 0 0ECN Stats: Avg Rx VC Q: 0 ForeSight RTD --Min-Pk bytes rcvd: -- FECN Frames: 0 FECN Ratio (%) 0Minutes Congested: -- BECN Frames: 0 BECN Ratio (%) 0Frames rcvd in excess of CIR: 0 Bytes rcvd in excess of CIR: 0Frames xmtd in excess of CIR: 0 Bytes xmtd in excess of CIR: 0This Command: dspchstats 14.1.1Hit DEL key to quit:Example (BPX)
Display the channel statistics for connection 4.1.50.1.
dspchstats 4.1.50.1
night TN SuperUser BPX 15 9.3 Apr. 13 2000 02:46 GMTChannel Statistics for 4.1.50.1 Cleared: Apr. 13 2000 02:53 (|)MCR: 0 cps Collection Time: 0 day(s) 18:10:22 Corrupted: NOTraffic Cells CLP Avg CPS %util Discards: CellsFrom Port : 14710 0 0 0 VcQ > CLP: 0To Network : 14710 --- 0 0 VcQ Full : 0From Network: 14710 --- 0 0 Qbin Full: 0To Port : 14710 14710 0 0 Qbin> CLP: 0Failed : 14710OAM Cells RsrcOVL : 0VC Q : 0 Tx OAM : 29608 NonCompliant: 0Rx EFCI : 0 Rx AIS : 14710Tx EFCI : 0 Rx FERF: 0 ForeSight CellsRx BCM : 0 Adj Up : 0Tx BCM : 0 Adj Dn : 0AAL-5 Frames: 0 Adj Fdn: 0This Command: dspchstats 4.1.50.1Hit DEL key to quit:Example (IGX)
Display statistics for connection 13.1.100 with a 10-second interval between screen updates.
dspchstats 13.1.100 10
sw142 TN SuperUser IGX 16 9.3 Apr. 13 2000 14:38 PDTChannel Statistics: 13.1.100 Cleared: Apr. 13 2000 11:50 (/)MCR: 150 cps Collection Time: 0 day(s) 00:00:00 Corrupted: NOCells Avg Util(cps) (%)From Port: 0 0 0To Network: 0 0 0Discarded: 0 0 0From Network: 0 0 0To Port: 0 0 0Discarded: 0 0 0This Command: dspchstats 13.1.100Hit DEL key to quit:Example (UXM on IGX)
Display statistics for connection 9.2.1.100. The card in slot 9 is a UXM.
dspchstats 9.2.1.100
sw199 TN SuperUser IGX 16 9.3 Apr. 13 2000 09:25 PDTChannel Statistics: 9.2.1.100 SnapshotCollection Time: 0 day(s) 13:28:47 Clrd: 08/27/97 19:47:24Type CountCells Received from Port 0Cells Transmitted to Network 0Cells Received from Network 0Cells Transmitted to Port 0EOF Cells Received from Port 0Cells Received with CLP=1 0Cells Received with CLP=0 0Non-Compliant Cells Received 0Average Rx VCq Depth in Cells 0Average Tx Vcq Depth in Cells 0Cells Transmitted with EFCI=1 0Cells Transmitted with EFCI=0 0Ingress Vsvd Allowed Cell Rate 0Egress Vsvd Allowed Cell Rate 0OAM state (0:OK,1:FERF,2:AIS) 0Good Pdu's Received by the Sar 0Good Pdu's Transmitted by the Sar 0Rx pdu's discarded by the Sar 0Tx pdu's discarded by the Sar 0Invalid CRC32 pdu rx by the sar 0Invalid Length pdu rx by the sar 0Shrt-Lgth Fail detected by the sar 0Lng-Lgth Fail detected by the sar 0Last Command: dspchstats 9.2.1.100Example (BPX)
Display statistics for connection 2.1.1.1 (with a VPI of 1, and VCI of 1), and an interval of 1.
dspchstats 2.1.1.1 1
sw57 TRM StrataCom BPX 8620 9.3 Date/Time Not SetChannel Statistics for 2.1.1.1 Cleared: Date/Time Not Set (\) SnapshotMCR: 96000/96000 cps Collection Time: 0 day(s) 00:01:45 Corrupted: NOTraffic Cells CLP Avg CPS %util Chan Stat Addr: 30EBB36CFrom Port : 0 0 0 0To Network : 0 --- 0 0From Network: 0 0 0 0To Port : 0 --- 0 0NonCmplnt Dscd: 0 Rx Q Depth : 0 Tx Q Depth : 0Rx Vsvd ACR : 0 Tx Vsvd ACR : 0 Bkwd SECB : 0Bkwd Lost Cell: 0 Bkwd Msin Cell: 0 Bkwd BIPV : 0Fwd SECB : 0 Fwd Lost Cell : 0 Fwd Msin Cell : 0Fwd BIPV : 0Last Command: dspchstats 2.1.1.1 1Next Command:CD Minor AlarmExample (IGX)
Display statistics for connection 10.1.205.101 (with a VPI of 205 and VCI of 101).
dspchstats 10.1.205.101
m2a TN StrataCom IGX 8420 9.3 Apr. 13 2000 14:19 GMTChannel Statistics: 10.1.205.101Collection Time: 0 day(s) 23:02:58 Clrd: 05/13/98 14:33:00Type Count Traffic Rate (cps)Cells Received from Port 82978 From port 0Cells Transmitted to Network 82978 To network 0Cells Received from Network 82978 From network 0Cells Transmitted to Port 82978 To port 0EOF Cells Received from Port 0Cells Received with CLP=1 0Cells Received with CLP=0 82978Non-Compliant Cells Received 0Average Rx VCq Depth in Cells 0Average Tx Vcq Depth in Cells 0Cells Transmitted with EFCI=1 0Cells Transmitted with EFCI=0 82978This Command: dspchstats 10.1.205.101Segmentation, Assembly, and Reassembly (SAR) Statistics for BXM Card
Table 4-16 provides some statistics information for SAR on the BXM card. The switch software collects miscellaneous statistics regarding the Monarch SAR (Segmentation, Assembly, and Reassembly). Note that the object name typically maps to the screen field name on the dspchstats screen.
