Displaying and Configuring UFM-U Cards

Displaying Card Parameters

To display the Card Configuration dialog for this device (using the rear or front view), right-click on the card to display the card "Configure" pop-up menu, then select Configure.

Front Card Configuration Dialog

Use this dialog to display UFM-U card characteristics, hardware, firmware, and status information. The Card Configuration dialog parameters are described in Table 15-1 .

Table 15-1: Card Configuration Dialog Parameters—Front View

Parameter	Description

Slot No	Identifies the slot the card is in.
Card Status	Status of the card. Examples are: Active—Card in use. No failure. Standby—Card idle. No failures. Failed—Card failed. Down—Card downed. Mismatch—Mismatch between front card and back card. Missing—An active card has been removed.
FrontCard Type	Identifies the type of front card. In this case, it is an NTM.
Front Card Serial#	Serial number on the front card.
FrontCard Revision	Model, hardware revision, and firmware revision of the front card.
Card Y-RedStatus	Card Y-Redundancy status. The values can be one of: primary, secondary, null.
AssocCard for Y-red	Associated slot for this card's Y-Redundancy. If the Card Y-RedStatus is primary, the secondary card index displays in this field. If the Card Y-RedStatus is secondary, the primary slot index displays in this field. If Card Y-RedStatus is null, a zero (0) appears in this field.
BOOTId	Boot ID of the processor card. If the card is not a processor card, this field is blank.
No. Ports (Front Card)	Number of ports on the front card.

Note This is not a configurable dialog.

Back Card Configuration Dialog

Use this dialog to view back card characteristics, hardware, firmware, and status information. The Card Configuration dialog parameters are described in Table 15-2.

Table 15-2: Card Configuration Dialog Parameters—Rear View

Parameter	Description

Slot No.	Number that identifies the slot the card is installed in.
Card Status	Status of the card. Examples are: Active—Card in use. No failure. Standby—Card idle. No failures. Failed—Card failed. Down—Card downed. Mismatch—Mismatch between front card and back card. Missing—An active card has been removed.
BackCard Type	Back card type.
BackCard Serial #	Serial number on the card.
BackCard Revision	Model number and hardware revision of the back card.
No. Ports (Backcard)	Number of ports on the back of the card.

Note The parameters in this dialog cannot be configured.

To open the Port Configuration dialog, right-click on a port (rear view) to display the "Configure" pop-up menu, then click Configure. The Port Configuration dialog is displayed. From the Category pull-down menu, select one of the following options:

IGX:PortConfig (This is the default dialog.)
IGX:Port Real-Time Counters

These dialogs are described in the subsections that follow.

Displaying and Configuring Logical Ports

To display and configure logical ports on a UFM-U card, select Logical Port Config from the Category>Ports menu. The Logical Port Config dialog displays as shown in Figure 15-1.

Figure 15-1: Logical Port Config Dialog

The parameters are described in Table 15-3.

Table 15-3: Port Configuration Dialog Parameters

Parameter	Description

Card Number	Number that identifies the slot the card is in.
Port Number	Number of the line.
Line number	Line number.
Admin Status	Admin status of the port. Choose one from the pop-up menu: up down modify add delete
Operational Status	Operational status of the port.
Port Speed	Port speed in Kbps.
Number of Channels	Number of channels.
Channel Speed	Channel speed in Kbps.
Starting channel	Starting channel number.
IDE to DE map	Choose yes or no from the pop-up menu.
LMI Operation Mode	Choose one from the pop-up menu: xdisabled lmi-asyn disabled lmi-noasyn uni-annexA uni-annexD nni-annexA nni-annexD auto-det

Configuring IGX Port Real-Time Counters

To display and configure Port real-time Counters on a UFM-U card, select IGX: Port Real-Time Counters from the Category>Ports menu. The IGX: Port Real-Time Counters dialog displays as shown in Figure 15-2.

Figure 15-2: IGX: Port Real-Time Counters Dialog Parameters

The parameters are described in Table 15-4.

Table 15-4: IGX Line Configuration Dialog Parameters


Parameter	Description
Card Number	Card number.
Port Number	Port number.
Rx Bytes	Traffic received in bytes.
Tx Bytes	Traffic transmitted in bytes.
Tx Frms	Traffic transmitted in frames.
Rx Frms	Traffic received frames.
Tx FECN Frms	The total number of frames transmitted with the FECN bit set.
Tx BECN Frms	The total number of frames transmitted with the BECN bit set.
# DE Frms Dropped	The total number of DE frames dropped due to queue threshold met.
Rx Frm CRC Errs	The total number of frames received with CRC errors.
Frms with Illegal Fmts	The total number of frames received with incorrect illegal formats.
Rx Alignment Err Frms	The total number of frames dropped with non-bytes aligned payload.
Rx Illegal Len Frms	The total number of frames received with illegal length.
# DMA Overruns	The total number of DMA overruns.
Unknown DLCIs	The total number of received frames with invalid/unknown DLCI dropped.
CLLM Tx Bytes	The total number of CLLM bytes transmitted.
CLLM Rx Bytes	The total number of CLLM frames received.
CLLM Tx Frms	The total number of CLLM frames transmitted.
CLLM Rx Frms	The total number of CLLM frames received.
CLLM Failures	The total number of CLLM failures.
LMI Fail Frames	The total number of LMI failure frames.
LMI Fail Bytes	The total number of LMI failure bytes.