Displaying and Configuring FTM Cards

Displaying Card Parameters

To display the Card Configuration dialog for this device (using the rear or front view), right-click on the card to display the card "Configure" pop-up menu, then select Configure.

Front Card Configuration Dialog

Use this dialog to display FTM card characteristics, hardware, firmware, and status information.The Card Configuration dialog parameters are described in Table 7-1 .

Table 7-1: Card Configuration Dialog Parameters—Front View

Parameter	Description

Slot No.	Identifies the slot the card is in.
Card Status	Status of the card. Examples are: Active—Card in use. No failure. Standby—Card idle. No failures. Failed—Card failed. Down—Card downed. Mismatch—Mismatch between front card and back card. Missing—An active card has been removed.
FrontCard Type	Identifies the type of front card. In this case, it is an NTM.
Front Card Serial#	Serial number on the front card.
FrontCard Revision	Model, hardware revision, and firmware revision of the front card.
Card Y-RedStatus	Card Y-Redundancy status. The values can be one of: primary, secondary, null.
AssocCard for Y-red	Associated slot for this card's Y-Redundancy. If the Card Y-RedStatus is primary, the secondary card index displays in this field. If the Card Y-RedStatus is secondary, the primary slot index displays in this field. If Card Y-RedStatus is null, a zero (0) appears in this field.
No. Ports (Front Card)	Number of ports on the front card.

Note This is not a configurable dialog.

Back Card Configuration Dialog

Use this dialog to view back card characteristics, hardware, firmware, and status information. The Card Configuration dialog parameters are described in Table 7-2.

Table 7-2: Card Configuration Dialog Parameters—Rear View

Parameter	Description

Slot No.	Number that identifies the slot the card is installed in.
Card Status	Status of the card. Examples are: Active—Card in use. No failure. Standby—Card idle. No failures. Failed—Card failed. Down—Card downed. Mismatch—Mismatch between front card and back card. Missing—An active card has been removed.
BackCard Type	Back card type.
BackCard Serial #	Serial number on the card.
BackCard Revision	Model number and hardware revision of the back card.
No. Ports (Backcard)	Number of ports on the back of the card.

Note The parameters in this dialog cannot be configured.

To open the Port Configuration dialog, right-click on a port or trunk (rear view) to display the "Configure" pop-up menu, then click Configure. The Port Configuration dialog is displayed. The Category pull-down menu provides two FTM Port dialogs.

IGX:PortConfig (This is the default dialog.)
IGX:Port Real-Time Counters

These dialogs are described in the subsections that follow.

Port Configuration

To display and configure Ports on an FTM card, select IGX: Port Config from the Category<Ports menu. The parameters are described in Table 7-3.

Table 7-3: Port Configuration Dialog Parameters

Parameter	Description

Card number	Number that identifies the slot the card is in.
Port Number	Port number of the logical port for that line.
Line Number	Number of the line.
Admin Status	Admin status of the port. Choose one from the pop-up menu: up down modify writeOnly add delete
Operational Status	Operational status of the port. Can be one of: active, failed, inactive, looped, unknown.
Port Speed	Baud rate of the port.
IDE to DE Map	Flag indicating whether or not the IDE to DE mapping should be performed. Choose one of the following from the pop-up menu: yes or no.
LMI Operation Mode	Local Management Interface (LMI) operation mode. Choose one from the pop-up menu: xdisabled lmi-asyn disabled lmi-noasyn uni-annexA uni-annexD nni-annexA nni-annexD auto-det

Configuring IGX Port Real-Time Counters

To display and configure Port Real-Time counters on an FTM card, select IGX: Port Real-Time Counters from the Category>Ports menu. The parameters are described in Table 7-4.

Table 7-4: IGX: Port Real-Time Counters Dialog Parameters

Parameter	Description

Card Number	Number that identifies the slot the card is in.
Port Number	Port number of the logical port for that line.
Rx Bytes	Traffic received in bytes.
Tx Bytes	Traffic transmitted in bytes.
Rx Frms	Traffic received in frames.
Tx Frms	Traffic transmitted frames.
Tx FECN Frms	Total number of frames transmitted with the FECN bit set.
Tx BECN Frms	Total number of frames transmitted with the BECN bit set.
# DE Frms Dropped	Total number of DE frames dropped due to queue threshold met.
Rx Frm CRC Errs	Total number of frames received with CRC errors.
Frms With Illegal Fmts	Total number of frames received with incorrect illegal formats.
Rx Alignment Err Frms	Total number of frames dropped with non-bytes aligned payload.
Rx Illegal Len Frms	Total number of frames received with illegal length.
# DMA Overruns	Total number of DMA overruns.
Unknown DLCIs	Total number of received frames with invalid/unknown DLCI dropped.
CLLM Tx Bytes	Total number of CLLM bytes transmitted.
CLLM Rx Bytes	Total number of CLLM frames received.
CLLM Tx Frms	Total number of CLLM frames transmitted.
CLLM Rx Frms	Total number of CLLM frames received.
CLLM Failures	Total number of CLLM failures.
LMI Fail Frames	Total number of LMI failure frames.
LMI Fail Bytes	Total number of LMI failure bytes.