PGW 2200 Softswitch Upgrade from Release 9.4(1) to 9.5(1)

Document ID: 60500

Introduction
Prerequisites
      Requirements
      Components Used
      Conventions
PGW 2200 Upgrade Procedure
      Verify TimesTen Replication on Host A and Host B
NetPro Discussion Forums - Featured Conversations
Related Information

Introduction

This document describes the process of upgrade from Cisco PGW 2200 Public Switched Telephone Network (PSTN) Gateway release 9.4(1) to 9.5(1). It explains the upgrade in both Call Control and Signaling mode.

Prerequisites

Requirements

Readers of this document should have knowledge of these topics:

Before you start the upgrade, consider these cautions:

caution Caution: Be sure that the Cisco PGW 2200 software is shut down before you start the upgrade. Also, be sure that the system administrator has logged in as root.

caution Caution: Always start the migration or upgrade from the PGW 2200 standby box.

Components Used

The information in this document is based on the PGW 2200 release 9.4(1) and later.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, refer to the Cisco Technical Tips Conventions.

PGW 2200 Upgrade Procedure

Complete these steps before you start the upgrade from PGW 2200 release 9.4(1) to 9.5(1):

Make a backup of the software that currently runs.

To do this, issue the mgcbackup.sh PGW 2200 command under the directory /opt/CiscoMGC/local.

mgcusr@PGW2200A% mgcbackup.sh

Backup Main Menu
----------------

Note: to exit the script at anytime use ctrl-c

1. Backup Now
2. Backup Schedule
3. Backup History
4. Exit

Enter option 1.

To check the TimesTen database, issue the command db_count.sh.

Note: For more information about the TimesTen database, refer to the document Configuring the Cisco MGC Software.

mgcusr@PGW2200A% db_count.sh
Counting the rows in each database table.

CISCO.A_CHARGE_ORIGIN   < 0 >
CISCO.A_NUMBERDIALPLANSELECTION < 2 >
CISCO.BLACKLIST_A       < 0 >
CISCO.BLACKLIST_B       < 0 >
CISCO.NUMBERTERM        < 0 >
CISCO.PORTEDNUMBERS     < 37 >
CISCO.WHITELIST_A       < 0 >
CISCO.WHITELIST_B       < 1 >

Check the replication between PGW 2200 active and standby.

mgcusr@PGW2200A% replication_status.sh
Replication status.

Peer name         Host name                 Port    State  Proto
----------------  ------------------------ ------  ------- -----
HOWDYDB           PGW2200B                 2980  Start       8

Last Msg Sent Last Msg Recv Latency TPS     RecordsPS Logs
------------- ------------- ------- ------- --------- ----
7578:18:28    -                0.03      38        38    1

Note: For a description of this output, refer to the replication.pdf file. You find the file in the directory /opt/TimesTen4.3/doc.

Ensure that you have the pom.dataSync parameter, located in XECfgParm.dat, set to false during the upgrade process. This is an example:
```
mgcusr@mgc-bru-22%  grep pom.data XECfgParm.dat
pom.dataSync =  false    # don't synch slave data with master
mgcusr@mgc-bru-22%
```
Refer to either the Release Notes for the Cisco Media Gateway Controller Software Release 9.4(1) or the Release Notes for the Cisco Media Gateway Controller Software Release 9.5(1)T. Also, see the information included in the Requirements section of this document.

Note: This is the valid order of steps to install PGW 2200 and upgrade it to the latest version:

Refer to the document Sun Solaris 8 Operating System Installation to be sure that the Solaris installation information matches your Sun station.

If it does not match, reinstall the software.

Note: Refer to the Solaris 8, Cisco MGC 9.2(x) and Higher Software Release Pre-Installation Checklists section of the document Preparing for Sun Solaris Operating System and Cisco MGC Software Installation.
Refer to the document Release Notes for the Solaris 8 Environment Packages for the CSCOh015 Solaris 8 Patch Cluster .

This patch contains the latest set of Solaris 2.8 patches that have been tested with the Cisco product. The version of this patch is 2.0(x). The patch is updated on a regular basis.
Install PGW 2200 software.
Install the Solaris system security patch CSCOh013.

To obtain the patch, refer to the System Security Patch section of the Release Notes for the Solaris 8 Environment Packages.
Reboot your Sun PGW 2200 station.

Note: For uninstallation, you must uninstall the CSCOh013 before you uninstall the PGW 2200 software. If you have installed the security package, you should remove it before you install Sun Solstice DiskSuite. Replace the security package after you complete the DiskSuite installation. If you have installed the security package without DiskSuite and removed it after the installation of DiskSuite, the box does not boot. You must remove the Solaris security package to upgrade the PGW 2200 release.

caution Caution: To begin the upgrade from 9.4(1), you first need to change the pom.dataSync entry in the XECfgParm.dat file. You find the file in the /opt/CiscoMGC/etc directory. Issue the UNIX editor command vi to change the entry to pom.dataSync = false. Make the change for both PGW 2200 active and standby status.

Complete these steps to perform the upgrade:

Close the PGW 2200 application.
From the cd /etc/init.d/ directory, issue the ./CiscoMGC stop command.
Navigate to the directory to which you have downloaded the new version of PGW 2200.
Check the file install.log for reported errors after the upgrade process.

Note: During the installation and uninstallation of the PGW 2200, files named uninstall.log and MGC_install.log are placed in /var/adm.

It is best to capture all the information displayed to the application you used for the upgrade process.
Issue the UNIX command chmod 774 uninstall.sh install.sh to make the unstall.sh and install.sh files executables.

Unstall the PGW 2200 release 9.4(1).

# ./uninstall.sh 


  
######################################################################################## 
# READ CAREFULLY BEFORE PROCEEDING!!!                                                  # 
# This uninstall will allow the user to return to the last good installation by        # 
# answering "NO" to the following question.  You MAY NOT install an arbitrary earlier  # 
# version of the software without experiencing fatal install problems.  If you do      # 
# return to the last good install prior to the current install, you will lose any      # 
# provisioning work you may have performed on the current software install.            # 
######################################################################################## 
 
Is the uninstall being done in order to upgrade to a new version of the 
software? [y] [y,n,?,q] y 
   
Use supplied admin file for unattended removal? [n] [y,n,?,q] y 

Restoring saved /opt/CiscoMGC/bin/almM 
Restoring saved /opt/CiscoMGC/bin/amDmpr 
Restoring saved /opt/CiscoMGC/bin/ca 
Restoring saved /opt/CiscoMGC/bin/cdrDmpr 
Restoring saved /opt/CiscoMGC/bin/cfgM 
Restoring saved /opt/CiscoMGC/bin/converter 
Restoring saved /opt/CiscoMGC/bin/EISUP 
Restoring saved /opt/CiscoMGC/bin/engine.no_smartalloc 
Restoring saved /opt/CiscoMGC/bin/engine.smartalloc 
Restoring saved /opt/CiscoMGC/bin/foverd 
Restoring saved /opt/CiscoMGC/bin/get_trc.sh 
Restoring saved /opt/CiscoMGC/bin/ioChanMgr 
Restoring saved /opt/CiscoMGC/bin/ISDNIP 
Restoring saved /opt/CiscoMGC/bin/ISDNL3 
Restoring saved /opt/CiscoMGC/bin/IUA 
Restoring saved /opt/CiscoMGC/bin/LogServerd 
Restoring saved /opt/CiscoMGC/bin/M3UA 
Restoring saved /opt/CiscoMGC/bin/measMgr 
Restoring saved /opt/CiscoMGC/bin/MGCP 
Restoring saved /opt/CiscoMGC/bin/mml 
Restoring saved /opt/CiscoMGC/bin/mmSAgt 
Restoring saved /opt/CiscoMGC/bin/pom 
Restoring saved /opt/CiscoMGC/bin/procM 
Restoring saved /opt/CiscoMGC/bin/replicator 
Restoring saved /opt/CiscoMGC/bin/sagt 
Restoring saved /opt/CiscoMGC/bin/sim 
Restoring saved /opt/CiscoMGC/bin/simWriter 
Restoring saved /opt/CiscoMGC/bin/SIP 
Restoring saved /opt/CiscoMGC/bin/sp 
Restoring saved /opt/CiscoMGC/bin/SS7 
Restoring saved /opt/CiscoMGC/bin/SUA 
Restoring saved /opt/CiscoMGC/bin/TALI 
Restoring saved /opt/CiscoMGC/bin/TCAP 
Restoring saved /opt/CiscoMGC/lib/libcmg.so 
Restoring saved /opt/CiscoMGC/lib/libconvutil.so 
Restoring saved /opt/CiscoMGC/lib/libcxn.so 
Restoring saved /opt/CiscoMGC/lib/libda.so 
Restoring saved /opt/CiscoMGC/lib/libeng.so 
Restoring saved /opt/CiscoMGC/lib/libengif.so 
Restoring saved /opt/CiscoMGC/lib/libhelp.so 
Restoring saved /opt/CiscoMGC/lib/libinf.so 
Restoring saved /opt/CiscoMGC/lib/libpolbase.so 
Restoring saved /opt/CiscoMGC/lib/libpolcomp.so 
Restoring saved /opt/CiscoMGC/lib/libpolfiles.so 
Restoring saved /opt/CiscoMGC/lib/libpolnuman.so 
Restoring saved /opt/CiscoMGC/lib/libpolroute.so 
Restoring saved /opt/CiscoMGC/lib/libpom.so 
Restoring saved /opt/CiscoMGC/lib/libpxe.so 
Restoring saved /opt/CiscoMGC/lib/libpxelog.so 
Restoring saved /opt/CiscoMGC/lib/librmg.so 
Restoring saved /opt/CiscoMGC/lib/librudp.so 
Restoring saved /opt/CiscoMGC/lib/libsa.so 
Restoring saved /opt/CiscoMGC/lib/libxe.so 
Restoring saved /opt/CiscoMGC/local/config-lib 
Restoring saved /opt/CiscoMGC/local/migrateTKGFile 
Restoring saved /opt/CiscoMGC/etc/alarmCats.dat 
Restoring saved /opt/CiscoMGC/etc/extNodeTypes.dat 
Restoring saved /opt/CiscoMGC/etc/measCats.dat 
Restoring saved /opt/CiscoMGC/etc/mmlCommands.dat 
Restoring saved /opt/CiscoMGC/etc/propSet.xml.dat 
Restoring saved /opt/CiscoMGC/etc/propVal.xsd.dat 
Restoring saved /opt/CiscoMGC/etc/variant.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/alarmCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/extNodeTypes.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/measCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/mmlCommands.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/properties.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/propSet.xml.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/propVal.xsd.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/variant.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/alarmCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/extNodeTypes.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/measCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/mmlCommands.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/propSet.xml.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/propVal.xsd.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/variant.dat 
Restoring saved /opt/CiscoMGC/etc/migrate/migrate_9.3001_9.4001 
Restoring saved /opt/CiscoMGC/etc/migrate/migrate_cpp_4_5 
Restoring saved /opt/CiscoMGC/etc/migrate/migrate_cpp_5_6 
Restoring saved /opt/CiscoMGC/.sw_config/mmlCommands.xml 
Backing out new file /opt/CiscoMGC/local/config-snmp 
Backing out new file /opt/CiscoMGC/local/delete_replication.sh 
Restoring saved /opt/Toolkit/bytecode/cdr/EntryLimit.tbc 
Restoring saved /opt/Toolkit/bytecode/cdr/File.tbc 
Restoring saved /opt/Toolkit/bytecode/cdr/position.dat 
Restoring saved /opt/Toolkit/bytecode/cdr/presentation.dat 
Restoring saved /opt/Toolkit/bytecode/cdr/search.tbc 
Restoring saved /opt/Toolkit/bytecode/toolbar/Toolbar.tbc 
Restoring saved /opt/Toolkit/bytecode/log/EntryLimit.tbc 
Restoring saved /opt/Toolkit/bytecode/log/File.tbc 
Restoring saved /opt/Toolkit/bytecode/am/AlarmView.tbc 
Restoring saved /opt/Toolkit/bytecode/am/EntryLimit.tbc 
Restoring saved /opt/Toolkit/bytecode/tv/EntryLimit.tbc 
Restoring saved /opt/Toolkit/bytecode/XECfg/XECfgParm.tbc 
  
Removal of <CSCOgs015> was successful.   

Removal of <CSCOgt001> was successful. 

110 1034430a    763  23   1  sctpmod (sctp streams module) 
unloading existing sctpmod 
index = 110   
  
Removal of <CSCOgd004> was successful. 
Removing /opt/CiscoMGC/etc/migrate/migrate.dat 
Removing /opt/CiscoMGC/etc/migrate/migrate_4_5 
Removing /opt/CiscoMGC/etc/migrate/migrate_5_6 
Removing /opt/CiscoMGC/etc/migrate/migrate_6_7 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.0001_7.0002 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.0001_7.1 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.0002_7.1 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.0003_7.1 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.0004_7.1 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.0005_7.1006 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.0_7.0001 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1001_7.1002 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1002_7.1003 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1003_7.1004 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1004_7.1005 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1005_7.1006 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1006_8.0 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1006_8.0.sql 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1007_7.1008 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1008_8.0 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1008_8.0.sql 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1009_8.0 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1009_8.0.sql 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1010_8.0001 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1010_8.0001.sql 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1_7.1001 
Removing /opt/CiscoMGC/etc/migrate/migrate_7.1_7.1001.sql 
Removing /opt/CiscoMGC/etc/migrate/migrate_8.0001_9.0 
Removing /opt/CiscoMGC/etc/migrate/migrate_8.0001_9.0001 
Removing /opt/CiscoMGC/etc/migrate/migrate_8.0_9.0 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.0001_9.0002 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.0002_9.0003 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.0003_9.1 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.0003_9.1.sql 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.0_9.0001 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.1001_9.1002 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.1002_9.2 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.1_9.1001 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.1_9.1002 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.2001_9.2002 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.2002_9.2003 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.2003_9.3 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.2_9.2001 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.3001_9.4001 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.3001_9.4001.sql 
Removing /opt/CiscoMGC/etc/migrate/migrate_9.3_9.3001 
Removing /opt/CiscoMGC/etc/migrate/migrate_XECfgParm 
Removing /opt/CiscoMGC/etc/migrate/migrate_cpp_4_5 
Removing /opt/CiscoMGC/etc/migrate/migrate_cpp_5_6 
Removing /opt/CiscoMGC/etc/migrate/migrate_cpp_DB 
Removing /opt/CiscoMGC/etc/migrate/migrate_db_to_91.sh 
Uninstalling /opt/CiscoMGC/etc/migrate/migrate_scr.tar.gz 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/4.0_to_5.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/4.0_to_5.0/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/4.0_to_5.0/dependencies.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/4.0_to_5.0/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/4.0_to_5.0/propLookUp.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/4.0_to_5.0/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/5.0_to_6.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/5.0_to_6.0/alarmCats.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/5.0_to_6.0/compTypes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/5.0_to_6.0/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/5.0_to_6.0/propSet.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/5.0_to_6.0/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/5.0_to_6.0/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/alarmCats.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/compTypes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/dependencies.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/measCats.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/6.0_to_7.0/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.0002/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.0002/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.0002/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.0002/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.1/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.1/compTypes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.1/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.1/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0001_to_7.1/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0002_to_7.1/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0002_to_7.1/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0002_to_7.1/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0002_to_7.1/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0003_to_7.1/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0003_to_7.1/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0003_to_7.1/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0003_to_7.1/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0004_to_7.1/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0004_to_7.1/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0004_to_7.1/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0004_to_7.1/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0005_to_7.1006/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0005_to_7.1006/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0005_to_7.1006/dependencies.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0005_to_7.1006/procGroups.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0005_to_7.1006/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0005_to_7.1006/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0_to_7.0001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0_to_7.0001/alarmCats.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0_to_7.0001/compTypes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0_to_7.0001/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0_to_7.0001/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0_to_7.0001/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.0_to_7.1/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1001_to_7.1002/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1001_to_7.1002/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1001_to_7.1002/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1002_to_7.1003/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1002_to_7.1003/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1003_to_7.1004/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1003_to_7.1004/dependencies.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1003_to_7.1004/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1003_to_7.1004/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1004_to_7.1005/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1004_to_7.1005/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1004_to_7.1005/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1005_to_7.1006/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1005_to_7.1006/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1006_to_8.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1006_to_8.0/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1006_to_8.0/services.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1007_to_7.1008/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1007_to_7.1008/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1008_to_8.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1008_to_8.0/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1009_to_8.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1009_to_8.0/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1010_to_8.0001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1010_to_8.0001/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1010_to_8.0001/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1010_to_8.0001/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1_to_7.1001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1_to_7.1001/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1_to_7.1001/dependencies.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1_to_7.1001/procGroups.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1_to_7.1001/processes.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.1_to_7.1001/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.2_to_9.1/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/7.2_to_9.1/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0001_to_9.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0001_to_9.0/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0001_to_9.0/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0001_to_9.0001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0001_to_9.0001/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0001_to_9.0001/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0_to_9.0/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0_to_9.0/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/8.0_to_9.0/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0001_to_9.0002/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0001_to_9.0002/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0002_to_9.0003/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0002_to_9.0003/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0003_to_9.1/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0003_to_9.1/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0003_to_9.1/accRespCat.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0_to_9.0001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.0_to_9.0001/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1001_to_9.1002/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1001_to_9.1002/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1002_to_9.2/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1002_to_9.2/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1_to_9.1001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1_to_9.1001/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1_to_9.1002/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.1_to_9.1002/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.2001_to_9.2002/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.2001_to_9.2002/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.2002_to_9.2003/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.2002_to_9.2003/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.2003_to_9.3/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.2003_to_9.3/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.2_to_9.2001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.3001_to_9.4001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.3001_to_9.4001/components.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.3001_to_9.4001/properties.mod 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.3_to_9.3001/ 
Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.3_to_9.3001/properties.modUninstalling 
/opt/CiscoMGC/etc/CONFIG_LIB/migrate_mod.tar.gz 

Removal of <CSCOgc001> was successful. 
   
Removal of <CSCOga005> was successful. 
Uninstalling /opt/Toolkit/tcl/tcl.tar.gz 
Uninstalling /opt/Toolkit/bytecode/tv/tv.tar.gz 
Uninstalling /opt/Toolkit/bytecode/toolbar/toolbar.tar.gz 
Uninstalling /opt/Toolkit/bytecode/log/Viewer.tar.gz 
Uninstalling /opt/Toolkit/bytecode/cdr/cdr.tar.gz 
Uninstalling /opt/Toolkit/bytecode/am/am.tar.gz 
Uninstalling /opt/Toolkit/bytecode/XECfg/XECfg.tar.gz 
Uninstalling /opt/Toolkit/Packages/Packages.tar.gz 
  
Removal of <CSCOga004> was successful. 
    
Removal of <CSCOga003> was successful. 
Exporting database contents for DSN=howdydb into /opt/CiscoMGC/etc/export.ttdb 
Backup started for datastore howdydb 
Backup Complete 
Successful backup, uninstall continuing 
Creating ttMigrate file 
Saving table CISCO.A_CHARGE_ORIGIN 
    Saving rows... 
    0/0 rows saved. 
Table successfully saved. 

Saving table CISCO.A_NUMBERDIALPLANSELECTION 

    Saving rows... 
    0/0 rows saved.Table successfully saved.   

Saving table CISCO.BLACKLIST_A 

    Saving rows... 
    0/0 rows saved.Table successfully saved. 

Saving table CISCO.BLACKLIST_B 

    Saving rows... 
    0/0 rows saved.Table successfully saved. 

Saving table CISCO.CLIIPADDRESS 

    Saving rows... 
    0/0 rows saved.Table successfully saved. 

Saving table CISCO.CLIPREFIX 

    Saving index CISCO.CLIPREFIX_IDX1 
    Saving rows... 
    0/0 rows saved.

Table successfully saved. 
  
Saving table CISCO.CMDGROUP 

    Saving rows... 
    71/71 rows saved. 
Table successfully saved. 
 
Saving table CISCO.H323IDDIVFROM 

    Saving rows... 
    0/0 rows saved. 
Table successfully saved. 

Saving table CISCO.NAMEDINPUTPARAMS 

    Saving index CISCO.NAMEDINIDX1 
    Saving rows... 
    103/103 rows saved. 
Table successfully saved. 

Saving table CISCO.NAMEDOUTPUTPARAMS 

    Saving index CISCO.NAMEDOUTIDX1 
    Saving rows... 
    40/40 rows saved. 
Table successfully saved. 

Saving table CISCO.NAMEDSQL 

    Saving index CISCO.NAMEDSQLIX1 
    Saving rows... 
    56/56 rows saved. 
Table successfully saved. 
 
Saving table CISCO.NUMBERTERM 

    Saving index CISCO.NUMBERTERM_IDX1 
    Saving rows... 
    0/0 rows saved. 
Table successfully saved. 

Saving table CISCO.PORTEDNUMBERS 

    Saving rows... 
    0/0 rows saved. 
Table successfully saved. 
 
Saving table CISCO.SCHEMA_VERSION

    Saving rows... 
    5/5 rows saved. 
Table successfully saved. 

Saving table CISCO.WHITELIST_A 

    Saving rows... 
    0/0 rows saved. 
Table successfully saved. 
 
Saving table CISCO.WHITELIST_B 

    Saving rows... 
    0/0 rows saved. 
Table successfully saved. 

Saving replication schema table TTREP.REPELEMENTS 

    Saving rows... 
    0/0 rows saved. 
Replication schema table successfully saved. 

Saving replication schema table TTREP.REPLICATIONS 

    Saving rows... 
    1/1 row saved. 
Replication schema table successfully saved. 

Saving replication schema table TTREP.REPPEERS 

    Saving rows... 
    0/0 rows saved. 
Replication schema table successfully saved. 

Saving replication schema table TTREP.REPSTORES 

    Saving rows... 
    0/0 rows saved. 
Replication schema table successfully saved. 

Saving replication schema table TTREP.REPSUBSCRIPTIONS 

    Saving rows... 
    0/0 rows saved. 
Replication schema table successfully saved. 
  
Saving replication schema table TTREP.REPTABLES 

    Saving rows... 
    0/0 rows saved. 
Replication schema table successfully saved. 
    

Saving replication schema table TTREP.TTSTORES 

    Saving rows... 
    0/0 rows saved. 
Replication schema table successfully saved. 
Successful ttMigrate, uninstall continuing 
The 32-bit daemon has stopped successfully. 
Modifying /etc/syslog.conf 
    
Removal of <CSCOga002> was successful. 

/opt/CiscoMGC/bin/engine: No such file or directory 
   
Removal of <CSCOga001> was successful. 
    
Removal of <CSCOga000> was successful. 

Modifying /etc/init.d/inetinit 
UX: userdel: ERROR: mgcusr is in use.  Cannot remove it. 
UX: groupdel: ERROR: Cannot update system files - group cannot be deleted. 

!--- Note: This is a normal error.


Removal of <CSCOgu000> was successful.    
Removal of <CSCO00016> was successful.    
Removal of <CSCO01016> was successful.   
Removal of <CSCO02016> was successful.  
Removal of <CSCO10016> was successful.   
Removal of <CSCO20016> was successful.   
Removal of <CSCO30016> was successful.   
Removal of <CSCO31016> was successful.  
Removal of <CSCO32016> was successful.   
Removal of <CSCO33016> was successful.   
Removal of <CSCO40016> was successful.  
Removal of <CSCO41016> was successful.   
Removal of <CSCO42016> was successful.   
Removal of <CSCO50016> was successful.   
Removal of <CSCO60016> was successful.   
Removal of <CSCO70016> was successful.   
Removal of <CSCO71016> was successful.   
Removal of <CSCO80016> was successful. 

Uninstallation log can be found in /var/adm/MGC_uninstall.log

To begin to install PGW 2200 version 9.5(1), issue the ./install.sh command.

Note: Each installation phase has successful or unsuccessful/failed information.

# ./install.sh 
  
Use supplied admin file for unattended install? [n] [y,n,?,q] y 
Base directory for Toolkit (default /opt/Toolkit) [?,q] 


!--- Note: If you want to upgrade or install the PGW 2200 toolkit, enter y.

 


########################################################################################### 
# The CSCOgu000 utilities package must be installed prior to other components             # 
# but has not been detected on your system.  This package contains all required system    # 
# parameters necessary for installing the rest of your software.  If you do not install   # 
# this package, the installation script will exit.                                        # 
########################################################################################### 
  
  
Would you like to install it now? [y] [y,n,?,q] y
  
  
Base directory for CiscoMGC (default /opt/CiscoMGC) [?,q]  

!--- Press enter.

Enter CiscoMGC user name [mgcusr] 
Enter CiscoMGC group name [mgcgrp] 
[mgcgrp] group already exists - continuing 
[mgcusr] user already exists - continuing 
Modifying /etc/init.d/inetinit   
  
Installation of <CSCOgu000> was successful.   
  
(c)1998 Cisco Systems, Inc. All Right Reserved. Unpublished -- rights reserved under 
the copyright laws of the United States.   
  
RESTRICTED RIGHTS LEGEND 
Use, duplication, or disclosure by the Government is subject to restrictions as 
set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer 
Software clause at DFARS 252.227-7013 or subparagraphs (c)(1) and (2) of 
Commercial Computer Software -- Restricted Rights at 48 CFR 52.227-19, as applicable. 
    
Cisco Systems, Inc. 
13615 Dulles Technology Drive 
Herndon, VA 20171 
    
Installation of <CSCOga000> was successful. 

Uncompressing EISUP 
Uncompressing ISDNIP 
Uncompressing ISDNL3 
Uncompressing IUA 
Uncompressing LI 
Uncompressing LogServerd 
Uncompressing M3UA 
Uncompressing MGCP 
Uncompressing SIP 
Uncompressing SS7 
Uncompressing SUA 
Uncompressing TALI 
Uncompressing TCAP 
Uncompressing almM 
Uncompressing amDmpr 
Uncompressing cdrDmpr 
Uncompressing cfgM 
Installing chk_inv 
Uncompressing engine.no_smartalloc 
Uncompressing engine.smartalloc 
Uncompressing foverd 
Uncompressing ioChanMgr 
Uncompressing measMgr 
Uncompressing mmBldCfg 
Uncompressing mmdbd 
Uncompressing mml 
Uncompressing pom 
Uncompressing procM 
Uncompressing replicator 
Installing libACE.so 
Uncompressing libbtsUtil.so 
Uncompressing libcmg.so 
Uncompressing libconvutil.so 
Uncompressing libcxn.so 
Uncompressing libda.so 
Uncompressing libeng.so 
Uncompressing libengif.so 
Uncompressing libhelp.so 
Uncompressing libinf.so 
Uncompressing libmmdb.so 
Uncompressing libpem.so 
Uncompressing libpolbase.so 
Uncompressing libpolcomp.so 
Uncompressing libpolfiles.so 
Uncompressing libpolnuman.so 
Uncompressing libpolroute.so 
Uncompressing libpom.so 
Uncompressing libpxe.so 
Uncompressing libpxelog.so 
Uncompressing librds.so 
Uncompressing librmg.so 
Uncompressing librudp.so 
Uncompressing libsa.so 
Installing libsunmath.so.1 
Installing libtten.so 
Uncompressing libxe.so 
Updating parameters for CiscoMGC 
Updating parameters for SW_Layout.cfg 
Updating parameters for helpCommands.xsd 
Updating parameters for mmlCommands.xml 
Updating parameters for mmlLICommands.xml 
Updating parameters for log_rotate.sh 
Updating parameters for startAudit.sh 
Updating parameters for diagdata 
Updating parameters for .create_liusr 
Updating parameters for .cshrc 
Updating parameters for .delete_liusr 
Updating parameters for .dump-prov 
Updating parameters for .master.cks 
Updating parameters for .perf_setup 
Updating parameters for backup.sh 
Updating parameters for config-lib 
Updating parameters for config-snmp 
Updating parameters for diskmonitor.sh 
Updating parameters for init.tcl 
Updating parameters for mgcbackup 
Updating parameters for mgcrestore 
Updating parameters for restore.sh 
Updating parameters for rmsem.sh 
Updating parameters for startAudit.mml 
Updating parameters for startLogServer 

Installation of <CSCOga001> was successful. 

Modifying /etc/syslog.conf 
Updating parameters for .odbc.ini 
Updating parameters for backupDb.sh 
Updating parameters for restoreDb.sh 
   Preparing to install TimesTen4.3 in /opt on mgc-bru-19 
   Executing TimesTen installation script...

Installing 32-bit version...   
  
Of the three components: 
  
  [1] TimesTen Client/Server and Data Manager 
  [2] TimesTen Data Manager Only 
  [3] TimesTen Client Only 
    
Begin installing in /opt/TimesTen4.3 ... 
Creating /opt/TimesTen4.3 ... 
Uncompressing... 
    
The TimesTen Demo applications can take up to 64 Mbytes of disk space. Depending on 
how your system is configured, you may not want to create the DemoDataStore 
directory in the default location : /var/TimesTen/TT4.3/32/DemoDataStore 
    
Creating /var/TimesTen/TT4.3/32/DemoDataStore ... 
    
System logging appears to be configured correctly. 
(TimesTen syslog messages seem to be recorded in the file '/var/adm/messages') 
Starting the daemon ... 
Installing TimesTen Server... 
Installing TimesTen Server startup/shutdown scripts... 
Creating new /var/TimesTen/sys.ttconnect.ini 
Creating /opt/TimesTen4.3/doc ... 
Extracting /opt/ttdb-install/doc/doc.tar ... 
End of TimesTen installation. 
   TimesTen installation script returned status 0 

Program complete 

Restoring backup schema. 
Restoring database contents for DSN=howdydb from /opt/CiscoMGC/etc/export.ttdb 
Restore started for datastore howdydb 
Restore completed 
    
Installation of <CSCOga002> was successful. 

smpd.cnf up to date, no configuration upgrade required 
Uncompressing mmSAgt 
Uncompressing sagt 
Uncompressing libsa.so 
Updating parameters for snmpd 
Updating parameters for critagt.cnf 
Updating inittab

Installation of <CSCOga003> was successful. 

Installing /opt/Toolkit/Packages/Packages.tar.gz 
Installing /opt/Toolkit/bytecode/XECfg/XECfg.tar.gz 
Installing /opt/Toolkit/bytecode/am/am.tar.gz 
Installing /opt/Toolkit/bytecode/cdr/cdr.tar.gz 
Installing /opt/Toolkit/bytecode/log/Viewer.tar.gz 
Installing /opt/Toolkit/bytecode/toolbar/toolbar.tar.gz 
Installing /opt/Toolkit/bytecode/tv/tv.tar.gz 
Installing /opt/Toolkit/tcl/tcl.tar.gz 
Updating parameters for MGC_Setup 
Updating parameters for MGC_Toolkit 
Updating parameters for init.tcl 
Updating parameters for toolbar.sh 
Updating parameters for toslaveside 
Setting VERSION=9.5(1) in version.dat 

Installation of <CSCOga004> was successful. 
  
Installation of <CSCOga005> was successful. 
Installing /opt/CiscoMGC/lib/perl5/5.00503.tar.gz 
Installing /opt/tibrv/tibco.tar.gz 
Updating parameters for tibco.cfg 
Updating parameters for tib4pgw.sh 
Updating parameters for tibAdapter.pl 
Updating parameters for tibsimulator.pl 
  
Installation of <CSCOga006> was successful. 

Installing ca 
Uncompressing callver 
Installing get_trc.sh 
Installing sim 
Installing simWriter 
Uncompressing siptool 
Installing sp 
  
Installation of <CSCOgt001> was successful. 

OS is 64-bits 
sctpmod not loaded 
loading sctpmod 

Installation of <CSCOgd004> was successful. 

Updating parameters for XECfgParm.dat 
Updating parameters for trigger.dat 
Updating parameters for migrate 
Updating parameters for migrateTKGFile 
Installing /opt/CiscoMGC/etc/CONFIG_LIB/migrate_mod.tar.gz 
Installing /opt/CiscoMGC/etc/migrate/migrate_scr.tar.gz 
  
Installation of <CSCOgc001> was successful. 

Uncompressing EISUP 
Uncompressing ISDNL3 
Uncompressing IUA 
Uncompressing LI 
Uncompressing M3UA 
Uncompressing MGCP 
Uncompressing SIP 
Uncompressing SS7 
Uncompressing SUA 
Uncompressing TALI 
Uncompressing TCAP 
Uncompressing amDmpr 
Installing ca 
Uncompressing cdrDmpr 
Uncompressing engine.no_smartalloc 
Uncompressing engine.smartalloc 
Uncompressing foverd 
Uncompressing ioChanMgr 
Uncompressing mmSAgt 
Uncompressing mml 
Uncompressing pom 
Uncompressing procM 
Uncompressing replicator 
Uncompressing sagt 
Installing sim 
Installing simWriter 
Installing sp 
Installing alarmCats.dat 
Installing extNodeTypes.dat 
Installing measCats.dat 
Installing propSet.xml.dat 
Installing propVal.xsd.dat 
Installing trigger.dat 
Installing variant.dat 
Installing alarmCats.dat 
Installing extNodeTypes.dat 
Installing measCats.dat 
Installing propSet.xml.dat 
Installing propVal.xsd.dat 
Installing properties.dat 
Installing trigger.dat 
Installing variant.dat 
Installing alarmCats.dat 
Installing extNodeTypes.dat 
Installing measCats.dat 
Installing migrate_cpp_4_5 
Installing migrate_cpp_5_6 
Installing migrate_cpp_DB 
Installing propSet.xml.dat 
Installing propVal.xsd.dat 
Installing variant.dat 
Uncompressing libcmg.so 
Uncompressing libconvutil.so 
Uncompressing libcxn.so 
Uncompressing libda.so 
Uncompressing libeng.so 
Uncompressing libengif.so 
Uncompressing libhelp.so 
Uncompressing libinf.so 
Uncompressing libmmdb.so 
Uncompressing libpolbase.so 
Uncompressing libpolcomp.so 
Uncompressing libpolfiles.so 
Uncompressing libpolnuman.so 
Uncompressing libpolroute.so 
Uncompressing libpxelog.so 
Uncompressing librmg.so 
Uncompressing libxe.so 
Updating parameters for migrate_9.4001_9.5001 
Updating parameters for migrate_XECfgParm 
Updating parameters for trigger.dat 
Updating parameters for delete_replication.sh 
Updating /opt/CiscoMGC/bin/amDmpr 
Updating /opt/CiscoMGC/bin/ca 
Updating /opt/CiscoMGC/bin/cdrDmpr 
Updating /opt/CiscoMGC/bin/EISUP 
Updating /opt/CiscoMGC/bin/engine.no_smartalloc 
Updating /opt/CiscoMGC/bin/engine.smartalloc 
Updating /opt/CiscoMGC/bin/foverd 
Updating /opt/CiscoMGC/bin/ioChanMgr 
Updating /opt/CiscoMGC/bin/ISDNL3 
Updating /opt/CiscoMGC/bin/IUA 
Updating /opt/CiscoMGC/bin/LI 
Updating /opt/CiscoMGC/bin/M3UA 
Updating /opt/CiscoMGC/bin/MGCP 
Updating /opt/CiscoMGC/bin/mml 
Updating /opt/CiscoMGC/bin/mmSAgt 
Updating /opt/CiscoMGC/bin/pom 
Updating /opt/CiscoMGC/bin/procM 
Updating /opt/CiscoMGC/bin/replicator 
Updating /opt/CiscoMGC/bin/sagt 
Updating /opt/CiscoMGC/bin/sim 
Updating /opt/CiscoMGC/bin/simWriter 
Updating /opt/CiscoMGC/bin/SIP 
Updating /opt/CiscoMGC/bin/sp 
Updating /opt/CiscoMGC/bin/SS7 
Updating /opt/CiscoMGC/bin/SUA 
Updating /opt/CiscoMGC/bin/TALI 
Updating /opt/CiscoMGC/bin/TCAP 
Updating /opt/CiscoMGC/etc/alarmCats.dat 
Updating /opt/CiscoMGC/etc/extNodeTypes.dat 
Updating /opt/CiscoMGC/etc/measCats.dat 
Updating /opt/CiscoMGC/etc/propSet.xml.dat 
Updating /opt/CiscoMGC/etc/propVal.xsd.dat 
Updating /opt/CiscoMGC/etc/trigger.dat 
Updating /opt/CiscoMGC/etc/variant.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/alarmCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/extNodeTypes.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/measCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/properties.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/propSet.xml.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/propVal.xsd.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/trigger.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/variant.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_testrmdp2/alarmCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_testrmdp2/extNodeTypes.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_testrmdp2/measCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_testrmdp2/propSet.xml.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_testrmdp2/propVal.xsd.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_testrmdp2/trigger.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_testrmdp2/variant.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/9.3001_to_9.4001/properties.mod 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/9.4001_to_9.5001/properties.mod 
Updating /opt/CiscoMGC/etc/migrate/migrate_9.4001_9.5001 
Updating /opt/CiscoMGC/etc/migrate/migrate_cpp_4_5 
Updating /opt/CiscoMGC/etc/migrate/migrate_cpp_5_6 
Updating /opt/CiscoMGC/etc/migrate/migrate_cpp_DB 
Updating /opt/CiscoMGC/etc/migrate/migrate_XECfgParm 
Updating /opt/CiscoMGC/lib/libcmg.so 
Updating /opt/CiscoMGC/lib/libconvutil.so 
Updating /opt/CiscoMGC/lib/libcxn.so 
Updating /opt/CiscoMGC/lib/libda.so 
Updating /opt/CiscoMGC/lib/libeng.so 
Updating /opt/CiscoMGC/lib/libengif.so 
Updating /opt/CiscoMGC/lib/libhelp.so 
Updating /opt/CiscoMGC/lib/libinf.so 
Updating /opt/CiscoMGC/lib/libmmdb.so 
Updating /opt/CiscoMGC/lib/libpolbase.so 
Updating /opt/CiscoMGC/lib/libpolcomp.so 
Updating /opt/CiscoMGC/lib/libpolfiles.so 
Updating /opt/CiscoMGC/lib/libpolnuman.so 
Updating /opt/CiscoMGC/lib/libpolroute.so 
Updating /opt/CiscoMGC/lib/libpxelog.so 
Updating /opt/CiscoMGC/lib/librmg.so 
Updating /opt/CiscoMGC/lib/libxe.so 
Updating /opt/CiscoMGC/local/delete_replication.sh 
Updating /opt/Toolkit/bytecode/cdr/EntryLimit.tbc 
Updating /opt/Toolkit/bytecode/cdr/File.tbc 
Updating /opt/Toolkit/bytecode/cdr/position.dat 
Updating /opt/Toolkit/bytecode/cdr/presentation.dat 
Updating /opt/Toolkit/bytecode/am/AlarmView.tbc 
Updating /opt/Toolkit/bytecode/am/EntryLimit.tbc 
Updating /opt/Toolkit/bytecode/tv/EntryLimit.tbc 
Updating /opt/Toolkit/bytecode/XECfg/XECfgParm.tbc 
mv: cannot access /opt/CiscoMGC/patch/CSCOgs002/local/.master.cks 
  
Installation of <CSCOgs002> was successful. 

Miscellaneous Protocols 
#################################### 
##        01       ##     02      ## 
#################################### 
##  BTNUP_BTNR167  ##  IETF_SIP   ## 
##  BTNUP_IUP           ##        ## 
##  DPNSS_BTNR188  ##             ## 
#################################### 
  
  
SS7 Protocl Family            PRI Protocol Family 
#########################     ###################### 
##          10         ##     ##        20        ## 
#########################     ###################### 
##  ANSISS7_92         ##     ##  ATT_41459       ## 
##  ANSISS7_C2         ##     ##  ATT_41459_C2    ## 
##  ANSISS7_C3         ##     ##  BELL_1268       ## 
##  ANSISS7_E1         ##     ##  BELL_1268_C2    ## 
##  ANSISS7_STANDARD   ##     ##  ETS_300_102     ## 
##  GR317              ##     ##  ETS_300_102_C2  ## 
##                     ##     ##  ETS_300_172     ## 
#########################     ###################### 
  
  
Q761 Version 1 Protocol Family 
########################################################################################## 
##          30         ##        31         ##          32       ##       33            ## 
########################################################################################## 
##  ETS_300_121        ##  Q761_BASE        ##  Q761_GERMAN      ##  Q761_SINGAPORE     ## 
##  ETS_300_356        ##  Q761_BELG        ##  Q761_INDIA       ##  Q761_SINGAPORE_C2  ## 
##  HONGKONG           ##  Q761_BELG_97VER  ##  Q761_KOREAN      ##  Q761_TAIWAN        ## 
##  ISUPV1_POLI        ##  Q761_CHILE       ##  Q761_NEWZEALAND  ##  Q761_THAILAND      ## 
##  Q761_ARGENTINA     ##  Q761_CHINA       ##  Q761_97VER_BASE  ##  Q761_MALAYSIAN     ## 
##  Q761_ARGENTINA_C2  ##  Q761_CHINA_C2    ##  Q761_PERU        ##                     ## 
##  Q761_AUSTRL        ##  Q761_DANISH      ##  Q761_PORTUGAL    ##                     ## 
##  Q761_AUSTRL_C2     ##                   ##                   ##                     ## 
########################################################################################## 
  
  
Q761 Version 2 Protocol Family                                         Q761 Version 3 
                                                                       Protocol Family 
###################################################################    #################### 
##         40         ##          41         ##          42      ##    ##       50       ## 
###################################################################    #################### 
##  ISUPV2_AUSTRIAN   ##  ISUPV2_JAPAN       ##  ISUPV2_VIETNAM  ##    ##  ISUPV3        ## 
##  ISUPV2_CZECH      ##  ISUPV2_JAPAN_C2    ##                  ##    ##  ISUPV3_UK     ## 
##  ISUPV2_DUTCH      ##  ISUPV2_NORWEGIAN   ##                  ##    ##  ISUPV3_UK_C2  ## 
##  ISUPV2_FINNISH96  ##  ISUPV2_POLISH      ##                  ##    ##  ISUPV3_UK_C3  ## 
##  ISUPV2_FRENCH     ##  ISUPV2_SPANISH     ##                  ##    ##  ISUPV3_UK_C4  ## 
##  ISUPV2_GERMAN     ##  ISUPV2_SPANISH_C2  ##                  ##    ##                ## 
##  ISUPV2_ISRAEL     ##  ISUPV2_SWISS       ##                  ##    ##                ## 
##                    ##  ISUPV2_SWISS_C2    ##                  ##    ##                ## 
###################################################################    #################### 
  
  
Q721 Protocol Family        Q767 Protocol Family 
#######################     ########################################## 
##         60        ##     ##        70        ##        71        ## 
#######################     ########################################## 
##  Q721_BASE        ##     ##  Q767_AUSTRALIA  ##  Q767_MEXICAN    ## 
##  Q721_BRAZILIAN   ##     ##  Q767_BASE       ##  Q767_NIGERIAN   ## 
##  Q721_CHINA       ##     ##  Q767_BRAZIL     ##  Q767_RUSS       ## 
##  Q721_FRENCH      ##     ##  Q767_COLOMBIA   ##  Q767_SINGAPORE  ## 
##  Q721_PHILLIPINE  ##     ##  Q767_GUATEMALA  ##  Q767_SPAN       ## 
##                   ##     ##  Q767_INDONESIA  ##  Q767_SWED       ## 
##                   ##     ##  Q767_ITAL       ##  Q767_TURKISH    ## 
##                   ##     ##  Q767_ITAL_C2    ##                  ## 
#######################     ########################################## 
  
  
Q931 Protocol Family 
###################### 
##       80         ## 
###################### 
##  Q931            ## 
##  Q931_AUSTRALIA  ## 
##  Q931_SINGAPORE  ## 
###################### 


    
Would you like to add a protocol set to your system? [y] [y,n,?,q] y 
Please insert a two digit package identifier and type <enter> If you choose to add 
 all protocols to your system, type "all": 
all 

Uncompressing ASP_NotRealProtocol.mdo 
Uncompressing ASP_NotRealProtocol.so 
Uncompressing CALLVER.mdo 
Uncompressing CALLVER.so 
Uncompressing CALLVER_GENERIC_ANALYSIS.mdo 
Uncompressing CALLVER_GENERIC_ANALYSIS.so 
Uncompressing CALLVER_LCM.mdo 
Uncompressing CDR_MAN.mdo 
Uncompressing CDR_MAN.so 
Uncompressing CONNECTION_PLANE_MANAGER.mdo 
Uncompressing CONNECTION_PLANE_MANAGER.so 
Uncompressing EISUP.mdo 
Uncompressing EISUP.so 
Uncompressing GENERIC_ANALYSIS.mdo 
Uncompressing GENERIC_ANALYSIS.so 
Uncompressing IN_TRIGGER.mdo 
Uncompressing IN_TRIGGER.so 
Uncompressing LEG_CONTROLLER.mdo 
Uncompressing LEG_CONTROLLER.so 
Uncompressing cc.mdo 
Uncompressing cc.so 
Uncompressing dummy.mdo 
Uncompressing dummy.so 
Uncompressing lcm.mdo 
Uncompressing lcm.so 

Installation of <CSCO00002> was successful. 

Uncompressing BTNUP_BTNR167.mdo 
Uncompressing BTNUP_BTNR167.so 
Uncompressing BTNUP_IUP.mdo 
Uncompressing BTNUP_IUP.so 
Uncompressing DPNSS_BTNR188.mdo 
Uncompressing DPNSS_BTNR188.so 
  
Installation of <CSCO01002> was successful. 

Uncompressing IETF_SIP.mdo 
Uncompressing IETF_SIP.so 
  
Installation of <CSCO02002> was successful. 

Uncompressing ANSISS7_2K.mdo 
Uncompressing ANSISS7_2K.so 
Uncompressing ANSISS7_92.mdo 
Uncompressing ANSISS7_92.so 
Uncompressing ANSISS7_C2.mdo 
Uncompressing ANSISS7_C2.so 
Uncompressing ANSISS7_C3.mdo 
Uncompressing ANSISS7_C3.so 
Uncompressing ANSISS7_E1.mdo 
Uncompressing ANSISS7_E1.so 
Uncompressing ANSISS7_STANDARD.mdo 
Uncompressing ANSISS7_STANDARD.so 
Uncompressing GR317.mdo 
Uncompressing GR317.so 

Installation of <CSCO10002> was successful. 

Uncompressing ATT_41459.mdo 
Uncompressing ATT_41459.so 
Uncompressing ATT_41459_C2.mdo 
Uncompressing ATT_41459_C2.so 
Uncompressing BELL_1268.mdo 
Uncompressing BELL_1268.so 
Uncompressing BELL_1268_C2.mdo 
Uncompressing BELL_1268_C2.so 
Uncompressing ETS_300_102.mdo 
Uncompressing ETS_300_102.so 
Uncompressing ETS_300_102_C2.mdo 
Uncompressing ETS_300_102_C2.so 
Uncompressing ETS_300_172.mdo 
Uncompressing ETS_300_172.so 

Installation of <CSCO20002> was successful. 

Uncompressing ETS_300_121.mdo 
Uncompressing ETS_300_121.so 
Uncompressing ETS_300_356.mdo 
Uncompressing ETS_300_356.so 
Uncompressing HONGKONG.mdo 
Uncompressing HONGKONG.so 
Uncompressing ISUPV1_POLI.mdo 
Uncompressing ISUPV1_POLI.so 
Uncompressing Q761_ARGENTINA.mdo 
Uncompressing Q761_ARGENTINA.so 
Uncompressing Q761_ARGENTINA_C2.mdo 
Uncompressing Q761_ARGENTINA_C2.so 
Uncompressing Q761_AUSTRL.mdo 
Uncompressing Q761_AUSTRL.so 
Uncompressing Q761_AUSTRL_C2.mdo 
Uncompressing Q761_AUSTRL_C2.so 

Installation of <CSCO30002> was successful. 

Uncompressing Q761_BASE.mdo 
Uncompressing Q761_BASE.so 
Uncompressing Q761_BELG.mdo 
Uncompressing Q761_BELG.so 
Uncompressing Q761_BELG_97VER.mdo 
Uncompressing Q761_BELG_97VER.so 
Uncompressing Q761_CHILE.mdo 
Uncompressing Q761_CHILE.so 
Uncompressing Q761_CHINA.mdo 
Uncompressing Q761_CHINA.so 
Uncompressing Q761_CHINA_C2.mdo 
Uncompressing Q761_CHINA_C2.so 
Uncompressing Q761_DANISH.mdo 
Uncompressing Q761_DANISH.so 
 
Installation of <CSCO31002> was successful. 

Uncompressing Q761_97VER_BASE.mdo 
Uncompressing Q761_97VER_BASE.so 
Uncompressing Q761_GERMAN.mdo 
Uncompressing Q761_GERMAN.so 
Uncompressing Q761_INDIA.mdo 
Uncompressing Q761_INDIA.so 
Uncompressing Q761_KOREAN.mdo 
Uncompressing Q761_KOREAN.so 
Uncompressing Q761_NEWZEALAND.mdo 
Uncompressing Q761_NEWZEALAND.so 
Uncompressing Q761_PERU.mdo 
Uncompressing Q761_PERU.so 
Uncompressing Q761_PORTUGAL.mdo 
Uncompressing Q761_PORTUGAL.so 
  
Installation of <CSCO32002> was successful. 

Uncompressing Q761_MALAYSIAN.mdo 
Uncompressing Q761_MALAYSIAN.so 
Uncompressing Q761_SINGAPORE.mdo 
Uncompressing Q761_SINGAPORE.so 
Uncompressing Q761_SINGAPORE_C2.mdo 
Uncompressing Q761_SINGAPORE_C2.so 
Uncompressing Q761_TAIWAN.mdo 
Uncompressing Q761_TAIWAN.so 
Uncompressing Q761_THAILAND.mdo 
Uncompressing Q761_THAILAND.so 
  
Installation of <CSCO33002> was successful. 

Uncompressing ISUPV2_AUSTRIAN.mdo 
Uncompressing ISUPV2_AUSTRIAN.so 
Uncompressing ISUPV2_CZECH.mdo 
Uncompressing ISUPV2_CZECH.so 
Uncompressing ISUPV2_DUTCH.mdo 
Uncompressing ISUPV2_DUTCH.so 
Uncompressing ISUPV2_FINNISH96.mdo 
Uncompressing ISUPV2_FINNISH96.so 
Uncompressing ISUPV2_FRENCH.mdo 
Uncompressing ISUPV2_FRENCH.so 
Uncompressing ISUPV2_GERMAN.mdo 
Uncompressing ISUPV2_GERMAN.so 
Uncompressing ISUPV2_ISRAEL.mdo 
Uncompressing ISUPV2_ISRAEL.so 
 
Installation of <CSCO40002> was successful. 

Uncompressing ISUPV2_JAPAN.mdo 
Uncompressing ISUPV2_JAPAN.so 
Uncompressing ISUPV2_JAPAN_C2.mdo 
Uncompressing ISUPV2_JAPAN_C2.so 
Uncompressing ISUPV2_NORWEGIAN.mdo 
Uncompressing ISUPV2_NORWEGIAN.so 
Uncompressing ISUPV2_POLISH.mdo 
Uncompressing ISUPV2_POLISH.so 
Uncompressing ISUPV2_SPANISH.mdo 
Uncompressing ISUPV2_SPANISH.so 
Uncompressing ISUPV2_SPANISH_C2.mdo 
Uncompressing ISUPV2_SPANISH_C2.so 
Uncompressing ISUPV2_SWISS.mdo 
Uncompressing ISUPV2_SWISS.so 
Uncompressing ISUPV2_SWISS_C2.mdo 
Uncompressing ISUPV2_SWISS_C2.so 
  
Installation of <CSCO41002> was successful. 

Uncompressing ISUPV2_VIETNAM.mdo 
Uncompressing ISUPV2_VIETNAM.so 

Installation of <CSCO42002> was successful. 

Uncompressing ISUPV3.mdo 
Uncompressing ISUPV3.so 
Uncompressing ISUPV3_UK.mdo 
Uncompressing ISUPV3_UK.so 
Uncompressing ISUPV3_UK_C2.mdo 
Uncompressing ISUPV3_UK_C2.so 
Uncompressing ISUPV3_UK_C3.mdo 
Uncompressing ISUPV3_UK_C3.so 
Uncompressing ISUPV3_UK_C4.mdo 
Uncompressing ISUPV3_UK_C4.so 
  
Installation of <CSCO50002> was successful. 

Uncompressing Q721_BASE.mdo 
Uncompressing Q721_BASE.so 
Uncompressing Q721_BRAZILIAN.mdo 
Uncompressing Q721_BRAZILIAN.so 
Uncompressing Q721_CHINA.mdo 
Uncompressing Q721_CHINA.so 
Uncompressing Q721_FRENCH.mdo 
Uncompressing Q721_FRENCH.so 
Uncompressing Q721_PHILLIPINE.mdo 
Uncompressing Q721_PHILLIPINE.so 
 
Installation of <CSCO60002> was successful. 

Uncompressing Q767_AUSTRALIA.mdo 
Uncompressing Q767_AUSTRALIA.so 
Uncompressing Q767_BASE.mdo 
Uncompressing Q767_BASE.so 
Uncompressing Q767_BRAZIL.mdo 
Uncompressing Q767_BRAZIL.so 
Uncompressing Q767_COLOMBIA.mdo 
Uncompressing Q767_COLOMBIA.so 
Uncompressing Q767_GUATEMALA.mdo 
Uncompressing Q767_GUATEMALA.so 
Uncompressing Q767_INDONESIA.mdo 
Uncompressing Q767_INDONESIA.so 
Uncompressing Q767_ITAL.mdo 
Uncompressing Q767_ITAL.so 
Uncompressing Q767_ITAL_C2.mdo 
Uncompressing Q767_ITAL_C2.so 

Installation of <CSCO70002> was successful. 

Uncompressing Q767_MEXICAN.mdo 
Uncompressing Q767_MEXICAN.so 
Uncompressing Q767_NIGERIAN.mdo 
Uncompressing Q767_NIGERIAN.so 
Uncompressing Q767_RUSS.mdo 
Uncompressing Q767_RUSS.so 
Uncompressing Q767_SINGAPORE.mdo 
Uncompressing Q767_SINGAPORE.so 
Uncompressing Q767_SPAN.mdo 
Uncompressing Q767_SPAN.so 
Uncompressing Q767_SWED.mdo 
Uncompressing Q767_SWED.so 
Uncompressing Q767_TURKISH.mdo 
Uncompressing Q767_TURKISH.so 
  
Installation of <CSCO71002> was successful. 

Uncompressing Q931.mdo 
Uncompressing Q931.so 
Uncompressing Q931_AUSTRALIA.mdo 
Uncompressing Q931_AUSTRALIA.so 
Uncompressing Q931_SINGAPORE.mdo 
Uncompressing Q931_SINGAPORE.so 

Installation of <CSCO80002> was successful. 
Beginning Check of System Performance Requirements 
  
Swap is total: 43776k bytes allocated + 53424k reserved = 97200k used, 4470696k 
 available 
Please Verify that you have over 4000000K Available swap 
  
Shutting down TimesTen Server: done. 
Installation completed Mon Mar  8 14:12:37 GMT 2004 
Installation log can be found in /var/adm/MGC_install.log 
# exit 
  
exit

Open the PGW 2200 application, and log in as superuser.

mgcusr@mgc-bru-19% su 
# cd /etc/init.d
# ./CiscoMGC start
    
Validating system and protocol package versions for consistency...please be patient. 
Migrating .dat files in /opt/CiscoMGC/etc 
Checking dialPlan dir: /opt/CiscoMGC/dialPlan/*.dialPlan 
Backing up dialPlans 
Checking dialPlan dir: /opt/CiscoMGC/dialPlan/*.bin 
Backing up binary dialplans 
Backing up .dat file 
Backing up database 
  
migrating XECfgParm.dat ... 
  
migrate_XECfgParm: setting *.transpathId = 02 
migrate_XECfgParm: setting *.ownTranspathId = 02 
migrate_XECfgParm: setting *.peerTranspathId = 01 
migrate_XECfgParm: setting *.MGC_CDR_NODE_ID = MGC-BRU-19 
migrate_XECfgParm: setting foverd.conn1Type = socket 
migrate_XECfgParm: setting foverd.conn2Type = socket 
migrate_XECfgParm: setting *.IP_Addr1 = 10.48.84.181 
migrate_XECfgParm: setting *.IP_Addr2 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_Addr3 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_Addr4 = 0.0.0.0 
migrate_XECfgParm: setting *.Virtual_IP_Addr1 = 10.48.84.85 
migrate_XECfgParm: setting *.Virtual_IP_Addr2 = 0.0.0.0 
migrate_XECfgParm: setting *.geoSeparation = false 
migrate_XECfgParm: setting *.sipFailover = false 
migrate_XECfgParm: setting *.IP_NextHop1 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_NextHop2 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_NextHop3 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_NextHop4 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_NextHop5 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_NextHop6 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_NextHop7 = 0.0.0.0 
migrate_XECfgParm: setting *.IP_NextHop8 = 0.0.0.0 
migrate_XECfgParm: setting *.ipAddrLocalA = 10.48.84.181 
migrate_XECfgParm: setting *.ipAddrLocalB = 0.0.0.0 
migrate_XECfgParm: setting *.ipAddrPeerA = 10.48.84.146 
migrate_XECfgParm: setting *.ipAddrPeerB = 0.0.0.0 
migrate_XECfgParm: setting *.SysConnectDataAccess = false 
migrate_XECfgParm: setting *.SysConnectDataAccess = false 
migrate_XECfgParm: setting foverd.abswitchPort = /dev/null 
migrate_XECfgParm: setting foverd.ipLocalPortA = 1052 
migrate_XECfgParm: setting foverd.ipLocalPortB = 1053 
migrate_XECfgParm: setting foverd.ipPeerPortA = 1051 
migrate_XECfgParm: setting foverd.ipPeerPortB = 1054 
migrate_XECfgParm: setting replicator.portDataChannelSend = 2968 
migrate_XECfgParm: setting replicator.portDataChannelRecv = 2970 
migrate_XECfgParm: setting replicator.portCommChannelSend = 2972 
migrate_XECfgParm: setting replicator.portCommChannelRecv = 2974 
migrate_XECfgParm: setting *.desiredPlatformState = slave 
migrate_XECfgParm: setting *.stPort = 0 
migrate_XECfgParm: setting pom.dataSync = false 
migrate_XECfgParm: setting *.chkPtPort = 2001 
migrate_XECfgParm: setting engine.SysPropagateChanAvail = false 
migrate_XECfgParm: setting engine.SysGeneratedCode = true 
migrate_XECfgParm: setting engine.SysGRSTimerInterval = 0 
migrate_XECfgParm: setting engine.SysGRSBlockSize = 0 
migrate_XECfgParm: setting engine.AuditTimerInterval = 1000 
migrate_XECfgParm: setting engine.MaxAuditCics = 32 
migrate_XECfgParm: setting engine.StartUpAuditEnabled = false 
migrate_XECfgParm: setting engine.CircuitReservation = false 
migrate_XECfgParm: setting engine.RelINAPCallsAfterSwOver = true 
migrate_XECfgParm: setting engine.SysVirtualSwitch = 1 
migrate_XECfgParm: setting engine.SysMdlMemoryReduction = 0 
migrate_XECfgParm: setting engine.CALL_MEM_BLOCK_SIZE = 145408 
migrate_XECfgParm: setting engine.CALL_MEM_CHUNK_SIZE = 145408 
migrate_XECfgParm: setting *.MaxNumTGAdvances = 1 
migrate_XECfgParm: setting *.ClearingLocation = 0 
migrate_XECfgParm: setting engine.MDLANumberScreening = 0 
migrate_XECfgParm: setting *.DefaultLocation = 0 
migrate_XECfgParm: setting *.detailedCallEventCapture = 1 
migrate_XECfgParm: setting *.DataBaseAccessError = 0 
migrate_XECfgParm: setting *.SelectTermCustGrpId = 0 
migrate_XECfgParm: setting engine.SysGSMTimerInterval = 10000 
migrate_XECfgParm: setting diskmonitor.Limit = 7 
migrate_XECfgParm: setting diskmonitor.Threshold = 80 
migrate_XECfgParm: setting diskmonitor.SoftLimit = false 
migrate_XECfgParm: setting diskmonitor.CdrRmFinished = 0 
migrate_XECfgParm: setting diskmonitor.CoreRmDays = 1 
migrate_XECfgParm: setting diskmonitor.CfgRmDirs = 64 
migrate_XECfgParm: setting *.logPrio = Error 
migrate_XECfgParm: setting *.logDirectory = ../var/log 
migrate_XECfgParm: setting *.logFileNamePrefix = platform 
migrate_XECfgParm: setting engine.CDRencodingFormat = AnsiCDB 
migrate_XECfgParm: setting engine.CDRtimeStamp = S 
migrate_XECfgParm: setting engine.CDRmessageTypes = "1010,1020,1030,1040,1050,1060,1070" 
migrate_XECfgParm: setting *.numberOfThreads = 0 
migrate_XECfgParm: setting *.dataSourceName = howdydb 
migrate_XECfgParm: setting *.maxNumLinks = 32 
migrate_XECfgParm: setting *.maxLinksPerSessionSet = 4 
migrate_XECfgParm: setting *.maxNumDChansPerIOCC = 504 
migrate_XECfgParm: setting *.maxNumMGCPLinks = 1000 
migrate_XECfgParm: setting *.maxNumRLMPorts = 8 
migrate_XECfgParm: setting *.GWClearChannelAlgorithm = G.clear; CCD 
migrate_XECfgParm: setting *.CallCutoffTimer = 0 
migrate_XECfgParm: setting *.CPUTimerInterval = 0 
migrate_XECfgParm: setting *.subSysCompVer = 8.b 
migrate_XECfgParm: setting *.dataCommitTime = 10 
migrate_XECfgParm: setting ioChanMgr.sessionPauseTimer = 8 
migrate_XECfgParm: setting ioChanMgr.resumeAckTimer = 1 
migrate_XECfgParm: setting MML.timeout = 10000 
migrate_XECfgParm: setting *.OverdecadicDigitsSupported = false 
migrate_XECfgParm: setting MML.enhancedHelpCompletion = true 
  
starting migration ... 
  
migrating from version 9.4001 to version 9.5001 ... 
migrating version.dat 
migrating variant.dat 
migrating alarmCats.dat 
migrating compTypes.dat 
migrating tables.dat 
migrating buckets.dat 
migrating alarmTable.dat 
migrating thresholds.dat 
migrating measProfs.dat 
migrating measCats.dat 
migrating mdlProcess.dat 
migrating extProcess.dat 
migrating extNodeTypes.dat 
migrating profileTypes.dat 
migrating mmlCommands.dat 
migrating propSet.xml.dat 
migrating propVal.xsd.dat 
migrating trigger.dat 
migrating priCharge.dat 
migrating priTariff.dat 
migrating meterTariff.dat 
migrating properties.dat 
migrating dial plan and route analysis files 
Migrating routing files... 
Migration routing file:routeAnalysis.dat: 
Migrating dial plans... 
Migration dialplan file:sSW3.dialPlan: 
Migrating IP links... 
Migrating C7IP links... 
migrating TimesTen database 
Migrating database from 9.4001 to 9.5001 
Database successfully migrated to 9.5001 
  
migration completed successfully 
Application started 
#exit 
  
exit 
mgcusr@mgc-bru-19% mml 
  
Copyright © 1998-2002, Cisco Systems, Inc. 
  
mgc-bru-19 mml> rtrv-ne 
   MGC-02 - Media Gateway Controller 2004-03-08 14:50:51.152 GMT 
M  RTRV 
   "Type:MGC" 
   "Hardware platform:sun4u sparc SUNW,Ultra-5_10" 
   "Vendor:"Cisco Systems, Inc."" 
   "Location:MGC-02 - Media Gateway Controller" 
   "Version:"9.5(1)"" 
   "Platform State:ACTIVE" 
   ; 
mgc-bru-19 mml>

Verify the PGW 2200 upgrade.
1. Log in as superuser.
2. From the /opt/CiscoMGC/bin directory, issue the command ./chk_inv -v.
  
  This performs an inventory check of the new installation.
```
# ./chk_inv -v
MGC Version: 9.5(1)

Read Checksum information...
Verify checksums of the MGC programs...

Checksum verification complete...

Check Solaris patch information...
Platform ('SUNW,UltraAX-i2',)
Read Solaris patch information...There are 'x' patches in 
 /opt/sun_install/Patct
OK
Solaris patch verification complete...

*** INVENTORY CHECK PASSED ***
#
```
  Note: If you have a warning and error message after you issue the chk_inv command after you have upgraded the Sun Solaris patches to the latest Cisco Solaris version, issue the cat /etc/release Unix command to see if you have the correct Sun Solaris software installed. If you have the incorrect Sun Solaris version on your PGW2200, the chk_inv command will not pass.
  
  Example: The Unix command used to check the Unix version running on your PGW2200:
```
# cat /etc/release 
Solaris 8 HW 2/02
Copyright 2002 Sun Microsystems, Inc.  All Rights Reserved.
```
  For information regarding Solaris 8 Software Release 2/04 (or Release 2/02 or 10/01), refer to Preparing for Sun Solaris Operating System and Cisco MGC Software Installation. These are the only Sun Solaris versions supported on the Cisco PGW2200.
Repeat Steps 1 through 9 for the other PGW 2200 that runs as active and now propagates to standby mode.

Caution: After you complete the upgrade on both systems, you need to change the pom.dataSync entry in the XECfgParm.dat file. You find the file in the /opt/CiscoMGC/etc directory. Issue the UNIX editor command vi to change the entry to pom.dataSync = true. Then, restart the PGW 2200 application with the command ./CiscoMGC start to allow the change to take effect.

Verify TimesTen Replication on Host A and Host B

Complete these steps to verify the TimesTen replication on host A and host B.

Issue the UNIX command ps -ef | grep timestenrepd on both PGW 2200 systems to verify that replication currently runs.
Issue the TransPath Man-Machine Language (MML) command rtrv-ne to check the status of both PGW 2200 systems.

One system should be in the active status, and the other system in standby status.
On both PGW 2200 systems, issue the command replication_status.sh to check that the replication currently runs.

The last message should be less than 10 seconds, and the log number is 1.
Optionally, you can issue the db_count.sh command again and compare the information with that shown in Step 2 of the section PGW 2200 Upgrade Procedure. The comparison allows you to verify that the upgrade did not result in the loss of any items.

If the database count is not the same as that shown in Step 2 of PGW 2200 Upgrade Procedure, issue the MML command sw-over::confirm to switch over to standby status.
- Issue these maintenance MML commands for verification.
  - mml> rtrv-softw:all
  - mml> rtrv-ne-health
  - mml> rtrv-iplnk:all
  - mml> rtrv-c7lnk:all
  - mml> rtrv-dest:all
  - mml> rtrv-alms
- Issue these UNIX commands for verification.
  - % df -k—Issue this command to be sure that there is enough disk space.
  - # swap -s—Issue this command to be sure that the system has enough memory.

NetPro Discussion Forums - Featured Conversations

Networking Professionals Connection is a forum for networking professionals to share questions, suggestions, and information about networking solutions, products, and technologies. The featured links are some of the most recent conversations available in this technology.

NetPro Discussion Forums - Featured Conversations for Voice

Service Providers: Voice over IP

Voice & Video: Voice over IP

Voice & Video: IP Telephony

Voice & Video: IP Phone Services for End Users

Voice & Video: Unified Communications

Voice & Video: IP Phone Services for Developers

Voice & Video: General

Related Information

Cisco PGW 2200 Softswitch Tech Notes
Cisco Signaling Controllers Configuration Examples
Voice Technology Support
Voice and Unified Communications Product Support
Recommended Reading: Troubleshooting Cisco IP Telephony
Technical Support & Documentation - Cisco Systems

Updated: Dec 04, 2006

Document ID: 60500

Hierarchical Navigation

Cisco PGW 2200 Softswitch