Document ID: 5730
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Configuration Steps
Related Information
Introduction
This document explains how to configure the Interface Controller Card (ICC) -T1 for Foreign Exchange Office (FXO) and Foreign Exchange Station (FXS) Loop Start (LS) and Ground Start (GS) circuits. The ICC is a high-capacity network interface engine that employs a midplane architecture which enables the network to connect with a series of I/O modules specific to different network interface requirements.
Prerequisites
Requirements
Readers of this document should have knowledge of these topics:
-
How to program a VCO/4K switch
-
Telephony analog signaling, such as FXS and FXO LS and GS circuits
Components Used
This document is applicable on Cisco VCO/4K with ICC-T1 spans running release 5.1.4 or later.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
Configuration Steps
In order to configure an ICC-T1 span for FXO and FXS LS and GS circuits, perform these steps.
-
With the Card Maintenance Screen, shown in this example, take the entire ICC (all 16 spans) Out of Service (OOS). In order to do this, enter 1,1,xx, where xx is an integer between seven and 21 inclusively and set the status to O to issue the C command.
C A R D M A I N T E N A N C E R L S CARD TYPE V.RV S ---------- ---------------------- ------------ 1 1 1-1 Network Bus 1.02 A 1 1 1-2 Tone Generator 1.25 A 1 1 2-1 Network Bus O 1 1 2-2 Tone Generator O 1 1 7- 8 Port Prompt/Record O 1 1 9-1-1 SPC-CPA O 1 1 21-1-1 ICC-T1 5.>2 M 1 1 21-1-2 ICC-T1 PRI/NI2 5.>2 M 1 1 21-1-3 ICC-T1 5.>2 M ADD, DELETE, CHANGE STATUS (A,D,C,P): _ _ _ ______ ______________________ _ AND PORT DEFINITION: 208 Out Of 4088 Time-Slots Allocated 1-64 ________ ________ ________ ________ ________ ________ _______ ________ 65-128 ________ ________ ________ ________ ________ ________ _______ ________
-
Go into the Card Summary Screen, shown in this example, and use Next Screen and Next Field in order to move the cursor to the span you want to configure.
C A R D S U M M A R Y LOCATION UNUSED DISP R L S CARD TYPE STATUS PORTS CARD ------------ ---------------------- -------- ------ ---- 1 1 1-1 Network Bus A 0 _ 1 1 1-2 Tone Generator A 1 _ 1 1 2-1 Network Bus O 0 _ 1 1 2-2 Tone Generator O 1 _ 1 1 7-8 Port Prompt/Record O 0 _ 1 1 9-1-1 SPC-CPA O 0 _ 1 1 21-1-1 ICC-T1 M 0 _ 1 1 21-1-2 ICC-T1 PRI/NI2 M 1 _ 1 1 21-1-3 ICC-T1 M 1 _ _ _ ______ ______________________ _ ___ _ _ _ ______ ______________________ _ ___ _ _ _ ______ ______________________ _ ___ _ _ _ ______ ______________________ _ ___ _ _ _ ______ ______________________ _ ___ _ _ _ ______ ______________________ _ ___ _ #00 Thu Aug 16, 2007 8:04 Not An Allowed Character Key
-
Press any letter on the keyboard followed by the Enter key in order to enter the Trunk Configuration Screen.
-
Use the Tab key to move the cursor down to Port 1, and use Next Field to go to the Signaling Type (SIG. TYPE).
ICC PROGRAMMABLE TRUNK CONFIGURATION SPAN LOCATION: R,L,S 1 1 21-1-1 STATUS: Maintenance CARD TYPE: ICC-T1 SPAN TYPE: SF CODE: AMI TXGAIN: 0db TXCLCK: SCLK SLIP: 255 ALM: SYS LENG: 0-133 RXGAIN: 0db RFCLCK: LOOP OOF: 17 TRUNK GROUP SIG. IMPULSE PORT NAME GROUP NAME TYPE RULE COS LAW ---- ---------- ----- ---------- ----- ------- ----- ----- 1 T1 2 ICC-FXO FXOLS 0 2 Mu 2 T1 2 ICC-FXO FXOLS 0 2 Mu 3 T1 2 ICC-FXO FXOLS 0 2 Mu 4 T1 2 ICC-FXO FXOLS 0 2 Mu 5 T1 2 ICC-FXO FXOLS 0 2 Mu 6 T1 2 ICC-FXO FXOLS 0 2 Mu 7 T1 2 ICC-FXO FXOLS 0 2 Mu 8 T1 2 ICC-FXO FXOLS 0 2 Mu #00 Thu Aug 16, 2007 8:07 -
Use Select in order to configure the port, as shown in this table.
VCO4K Setting FAR END EQ. Setting ------------------------------------------------------------- FXOLS FXSLS FXSLS FXOLS FXOGS FXSGS FXSGS FXOGS
-
You have two options in order to reactivate the ICC. The first is to go back to the Card Maintenance Screen and follow the guidelines in Step 1, but replace Status O with A. You can also physically reseat the ICC. Once the ICC comes back up, the span that was changed runs the new protocol.
Related Information
- Voice Technology Support
- Voice and Unified Communications Product Support
- Recommended Reading: Troubleshooting Cisco IP Telephony
- Technical Support & Documentation - Cisco Systems
| Updated: Feb 02, 2006 | Document ID: 5730 |