Table Of Contents
Displaying the SPA Hardware Type
Example of the show interface Command
Overview of the Serial SPAs
This chapter provides an overview of the release history, and feature and MIB support for the Cisco 12000 SIP-400, Cisco 12000 SIP-401, Cisco 12000 SIP-501, and Cisco 12000 SIP-601with the 2-Port and 4-Port Clear Channel T3/E3 SPA, 2-Port and 4-Port Channelized T3 SPA, 1-Port Channelized OC-3/STM-1 SPA, and the 8-Port Channelized T1/E1 SPA.
This chapter includes the following sections:
•
Displaying the SPA Hardware Type
Release History
Supported Features
This section provides a list of some of the primary features supported by the SIP and SPA hardware and software.
SIP-400 Features
The SIP-400 is a carrier card designed to process packets between different Shared Port Adapters (SPAs) and the Cisco 12000.
•
•
•
The SIP-400 supports the standard FPGA upgrade methods for the Cisco 12000 Series router.
•
SPA Features
The following is a list of some of the significant software features supported by the 2-Port and 4-Port Channelized T3 SPA, 2-Port and 4-Port Clear Channel T3/E3 SPA, 8-Port Channelized T1/E1 SPA, and 1-Port Channelized OC-3/STM-1 SPA:
•
•
•
•
–
–
–
•
•
•
•
•
•
•
•
•
Channelized T1 Features
–
–
–
–
–
–
–
–
–
–
Channelized T3 Features
–
–
–
–
–
–
–
–
–
- Alarm indication signal (AIS)
- Out of frame (OOF)
- Far-end receive failure (FERF)
–
–
- Digital Link
- ADC Kentrox
- Adtran
- Verilink
- Larscom
Unchannelized E1 Features
–
–
–
–
–
Unchannelized E3 Features
–
–
–
–
–
–
–
–
- Digital Link
- ADC Kentrox
- Adtran
- Verilink
- Larscom
Restrictions
•
–
–
Supported MIBs
The following MIBs are supported in Cisco IOS Release 12.2S for the serial SPAs on the Cisco 12000 Series routers:
All serial SPAs:
•
•
•
•
•
•
•
•
•
•
•
•
•
2 and 4-Port T3/E3 SPAs:
•
8-Port Channelized T1/E1 SPA:
•
2 or 4-Port CT3 SPA
•
•
•
•
•
To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:
http://tools.cisco.com/ITDIT/MIBS/servlet/index
If Cisco MIB Locator does not support the MIB information that you need, you can also obtain a list of supported MIBs and download MIBs from the Cisco MIBs page at the following URL:
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
To access Cisco MIB Locator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions found at this URL:
Displaying the SPA Hardware Type
To verify the SPA hardware type that is installed in your Cisco 12000 Series router, you can use the show diagbus command or the show interfaces command (can be used only if the interface has been configured). There are several other commands on the Cisco 12000 series routers that also provide SPA hardware information.
Table 8-1 shows the hardware description that appears in the show command output for each type of SPA that is supported on the Cisco 12000 series router.
Example of the show interface Command
The following example shows output from the show interface serial 0/0/0 command on a Cisco 12008 router with a 4-Port Channelized T3 SPA installed in slot 7:
Router#show interface serial 7/0/0/1Serial7/0/0/1:0 is down, line protocol is downHardware is SPA-4XCT3/DS0MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, rely 255/255, load 1/255Encapsulation FRAME-RELAY, crc 16, loopback not setKeepalive set (10 sec)LMI enq sent 0, LMI stat recvd 0,LMI upd recvd 0LMI enq recvd 0, LMI stat sent 0,LMI upd sent 0, DCE LMI downLMI DLCI 1023 LMI type is CISCO frame relay DCEBroadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0Last input never, output never, output hang neverLast clearing of "show interface" counters 1d17hQueueing strategy: fifoOutput queue 0/40, 0 drops; input queue 0/75, 0 dropsAvailable Bandwidth 1536 kilobits/sec5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec0 packets input, 0 bytes, 0 no bufferReceived 0 broadcasts, 0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort0 packets output, 0 bytes, 0 underruns0 output errors, 0 collisions, 0 interface resets0 output buffer failures, 0 output buffers swapped out0 carrier transitions no alarm presentVC 1: timeslot(s): 1-24, Transmitter delay 0, non-inverted dataRouter#Router#show gsrSlot 0 type = Performance Route Processorstate = ACTV RP IOS Running ACTIVESlot 3 type = 12 Port Packet over DS3state = IOS RUN Line Card EnabledSlot 4 type = 4 Port Packet Over SONET OC-12c/STM-4state = IOS RUN Line Card EnabledSlot 6 type = 1 Port Packet Over SONET OC-192c/STM-64state = IOS RUN Line Card EnabledSlot 7 type = ISE 2.5G SPA Interface Cardstate = IOS RUN Line Card Enabledsubslot 7/0: SPA-4XCT3/DS0 (0x43B), status is oksubslot 7/1: Emptysubslot 7/2: SPA-1XCHSTM1/OC3 (0x463), status is out of servicesubslot 7/3: EmptySlot 16 type = Clock Scheduler Card 16XOC192state = Card PoweredSlot 17 type = Clock Scheduler Card 16XOC192state = Card Powered PRIMARY CLOCKSlot 18 type = Switch Fabric Card 16XOC192state = Card PoweredSlot 19 type = Switch Fabric Card 16XOC192state = Card PoweredSlot 20 type = Switch Fabric Card 16XOC192state = Card PoweredSlot 24 type = Alarm Module(16)state = Card PoweredSlot 25 type = Alarm Module(16)state = Card PoweredSlot 27 type = Bus Board(16)state = Card PoweredSlot 28 type = Blower Module(16)state = Card PoweredSlot 29 type = Blower Module(16)state = Card Powered