Cisco ONS 15454 SDH Troubleshooting and Maintenance Guide, Release 3.4
Chapter 2, General Troubleshooting

Table Of Contents

General Troubleshooting

2.1 Network Troubleshooting Tests

2.2 Identify Points of Failure on a Circuit Path

2.2.1 Perform a Facility Loopback on a Source E3-12 Port

2.2.2 Perform a Hairpin on a Source Node Port

2.2.3 Perform a Terminal Loopback on a Destination E3-12 Port

2.2.4 Perform a Facility Loopback on a Destination E3-12 Port

2.3 PC Connectivity Troubleshooting

2.3.1 Unable to Verify the IP Configuration of your PC

2.3.2 Browser Login Does Not Launch Java

2.3.3 Unable to Verify the NIC Connection on your PC

2.3.4 Verify PC Connection to the ONS 15454 SDH (ping)

2.4 CTC Operation Troubleshooting

2.4.1 Browser Stalls When Downloading CTC JAR Files From TCC-I

2.4.2 CTC Does Not Launch

2.4.3 Sluggish CTC Operation or Login Problems

2.4.4 Node Icon is Grey on CTC Network View

2.4.5 CTC Cannot Launch Due to Applet Security Restrictions

2.4.6 Java Runtime Environment Incompatible

2.4.7 Different CTC Releases Do Not Recognize Each Other

2.4.8 Username or Password Does Not Match

2.4.9 No IP Connectivity Exists Between Nodes

2.4.10 DCC Connection Lost

2.4.11 "Path in Use" Error When Creating a Circuit

2.4.12 Calculate and Design IP Subnets

2.4.13 Ethernet Connections

2.4.14 VLAN Cannot Connect to Network Device from Untag Port

2.4.15 Cross-Connect Card Oscillator Fails

2.5 Circuits and Timing

2.5.1 Circuit Transitions to Partial State

2.5.2 TU-AIS on Unused VC Circuits

2.5.3 Circuit Creation Error with VC Circuit

2.5.4 ONS 15454 SDH Switches Timing Reference

2.5.5 Holdover Synchronization Alarm

2.5.6 Free-Running Synchronization Mode

2.5.7 Daisy-Chained SETS Not Functioning

2.6 Fiber and Cabling

2.6.1 Bit Errors Appear for a Traffic Card

2.6.2 Faulty Fiber-Optic Connections

2.6.3 Optical Card Transmit and Receive Levels

2.7 Power and LED Tests

2.7.1 Power Supply Problems

2.7.2 Power Consumption for Node and Cards

2.7.3 Lamp Test for Card LEDs


General Troubleshooting


This chapter provides procedures for troubleshooting the most common problems encountered when operating a Cisco ONS 15454 SDH. To troubleshoot specific ONS 15454 SDH alarms, see Chapter 1, "Alarm Troubleshooting." If you cannot find what you are looking for in this chapter or Chapter 1, "Alarm Troubleshooting," contact the Cisco Technical Assistance Center (TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

This chapter begins with the following sections on network problems:

Network Troubleshooting Tests—Describes loopbacks and hairpin circuits, which you can use to test circuit paths through the network or logically isolate faults.

Identify Points of Failure on a Circuit Path—Explains how to perform the tests described in the "Network Troubleshooting Tests" section.

The remaining sections describe symptoms, problems, and solutions that are categorized according to the following topics:

PC Connectivity Troubleshooting—Provides troubleshooting procedures for PC and network connectivity to the ONS 15454 SDH

CTC Operation Troubleshooting—Provides troubleshooting procedures for CTC log-in or operation problems.

CTC Operation Troubleshooting—Provides troubleshooting procedures for CTC log-in or operation errors and PC and network connectivity.

Circuits and Timing—Provides troubleshooting procedures for circuit creation, error reporting, and timing reference errors and alarms.

Fiber and Cabling—Provides troubleshooting procedures for fiber and cabling connectivity errors.

2.1 Network Troubleshooting Tests

Use loopbacks and hairpins to test newly created circuits before running live traffic or to logically locate the source of a network failure. All ONS 15454 SDH line (traffic) cards, except Ethernet cards, allow loopbacks and hairpins.


Caution On multiport STM-N cards, a loopback applies to the entire card and not an individual circuit. Exercise caution when using loopbacks on an STM-N card carrying live traffic.

A facility loopback tests the line interface unit (LIU) of a card, the FMEC, and related cabling. After applying a facility loopback on a card, use a test set to run traffic over the loopback. A successful facility loopback eliminates the LIU, FMEC, or cabling as the potential cause of a network problem. Figure 2-1 shows a facility loopback on a E3-12 card.

Figure 2-1 The facility loopback process on an E3-12 card

Figure 2-2 shows a facility loopback on a STM-N card.


Caution Before performing a facility loopback on an STM-N card, make sure the card contains at least two SDCC paths to the node where the card is installed. A second SDCC path provides a non-looped path to log into the node after the loopback is applied, thus enabling you to remove the facility loopback. Ensuring a second SDCC is not necessary if you are directly connected to the ONS 15454 SDH containing the loopback OC-N.

Figure 2-2 The facility loopback process on a STM-N card

A terminal loopback tests a circuit path as it passes through the cross-connect card (XC10G) and as it loops back from the card being tested. Figure 2-3 shows a terminal loopback on an STM-N card. The test-set traffic comes in on the E3-12 card and goes through the cross-connect card to the STM-N card. The terminal loopback on the STM-N card turns the signal around before it reaches the LIU and sends it through the cross-connect card to the E3-12 card. This test verifies that the cross-connect card and circuit paths are valid, but does not test the LIU on the STM-N card.

Figure 2-3 The terminal loopback process on an STM-N card

To test the LIU on an STM-N card, connect an optical test set to the STM-N card ports and perform a facility loopback or use a loopback or hairpin on a card that is farther along the circuit path. Figure 2-4 shows a terminal loopback on an E3-12 card. The test-set traffic comes in on the STM-N card and goes through the cross-connect card to the E3-12 card. The terminal loopback on the E3-12 card turns the signal around before it reaches the LIU and sends it through the cross-connect card to the STM-N card. This test verifies that the cross-connect card and circuit paths are valid, but does not test the LIU on the E3-12 card.

Figure 2-4 The terminal loopback process on an E3-12 card

A hairpin circuit brings traffic in and out on an E3-12 port rather than sending the traffic onto the STM-N card. A hairpin loops back only the specific E3 circuit and does not cause an entire STM-N port to loop back, thus preventing a drop of all traffic on the STM-N port. The hairpin allows you to test a circuit on nodes running live traffic. Figure 2-5 shows a hairpin circuit on an E3-12 card.

Figure 2-5 The hairpin circuit process on an E3-12 card

2.2 Identify Points of Failure on a Circuit Path

Facility loopbacks, terminal loopbacks, and hairpin circuits are often used together to test the circuit path through the network or to logically isolate a fault. Performing a network test at each point along the circuit path systematically eliminates possible points of failure. The example in this section tests an E3-12 circuit on a two-node MS-SPRing. Using a series of facility loopbacks, terminal loopbacks, and hairpins, the path of the circuit is traced and the possible points of failure eliminated.

A logical progression of four network test procedures apply to this scenario:


Note The test sequence for your circuits will differ according to the type of circuit and network topology.


1. A facility loopback on the source-node E3-12 card

2. A hairpin on the source-node E3-12 card

3. A terminal loopback to the destination-node E3-12 card

4. A facility loopback to the destination E3-12 card


Note All loopback tests require on-site personnel.


2.2.1 Perform a Facility Loopback on a Source E3-12 Port

The facility loopback test is performed on the node source port in the network circuit, in this example, the E3-12 port in the source node. Completing a successful facility loopback on this port isolates the cabling, the E3-12 card, and the FMEC as possible failure points. Figure 2-6 shows an example of a facility loopback on a source E3-12 port.

The facility loopback test is performed on the source card in the network circuit, in this example, the source traffic card in the source node. Completing a successful facility loopback on this card eliminates the cabling, the E3-12 card, and the FMEC as possible failure points. shows an example of a facility loopback.

Figure 2-6 A facility loopback on a circuit source E3-12 port


Caution Performing a loopback on an in-service circuit is service-affecting.

Procedure: Create the Facility Loopback on the Source E3-12 Port


Step 1 Connect an electrical test set to the port you are testing.

a. Use appropriate cabling to attach the transmit (Tx) and receive (Rx) terminals of the electrical test set to the FMEC connectors or DSx panel for the port you are testing. The transmit (Tx) and receive (Rx) terminals connect to the same port.

b. Adjust the test set accordingly.

Step 2 Use CTC to create the facility loopback circuit on the port being tested:

a. In node view, double-click the card where you will perform the loopback.

b. Click the Maintenance > Loopback tabs.

c. Choose OOS_MT from the State column for the port being tested. If this is a multiport card, select the appropriate row for the port being tested.

d. Choose Facility (Line) from the Loopback Type column for the port being tested. If this is a multiport card, select the appropriate row for the desired port.

e. Click Apply.

f. Click Yes in the Confirmation Dialog box.


Note It is normal for an alarm to appear during loopback setup. The alarm clears when you remove the loopback.


Step 3 Proceed to the "Test the Facility Loopback Circuit" section.


Procedure: Test the Facility Loopback Circuit


Step 1 If the test set is not already sending traffic, send test traffic on the loopback circuit.

Step 2 Examine the traffic received by the test set. Look for errors or any other signal information that the test set is capable of indicating.

Step 3 If the test set indicates a good circuit, no further testing is necessary with the facility loopback:

Clear the loopback circuit before testing the next segment of the network circuit path.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

Proceed to the "Perform a Hairpin on a Source Node Port" section.

Step 4 If the test set indicates a faulty circuit, the problem may be a faulty E3-12 card, faulty cabling from the E3-12 card to the DSx panel or the FMEC, or a faulty FMEC.

Proceed to the "Test the E3-12 Cabling" section.


Procedure: Test the E3-12 Cabling


Step 1 Replace the suspect cabling (the cables from the test set to the DSx panel or the FMEC ports) with a known-good cable.

If a known-good cable is not available, test the suspect cable with a test set. Remove the suspect cable from the DSx panel or the FMEC and connect the cable to the transmit (Tx) and receive (Rx) terminals of the test set. Run traffic to determine whether the cable is good or suspect.

Step 2 Resend test traffic on the loopback circuit with a known-good cable installed.

Step 3 If the test set indicates a good circuit, the problem was probably the defective cable.

Replace the defective cable.

Clear the loopback circuit before testing the next segment of the network circuit path.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

Proceed to the "Perform a Hairpin on a Source Node Port" section.

Step 4 If the test set indicates a faulty circuit, the problem may be a faulty card or a faulty FMEC.

Proceed to the "Test the E3-12 Card" section.


Procedure: Test the E3-12 Card


Step 1 Replace the suspect card with a known-good card. See "Card Replacement" section on page 4-17.

Step 2 Resend test traffic on the loopback circuit with a known-good card installed.

Step 3 If the test set indicates a good circuit, the problem is probably the defective card.

Return the defective card to Cisco through the returned materials authorization (RMA) process. Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Replace the faulty card. See "Card Replacement" section on page 4-17.

Clear the loopback circuit before testing the next segment of the network circuit path.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

Proceed to the "Perform a Hairpin on a Source Node Port" section.

Step 4 If the test set indicates a faulty circuit, the problem may be a faulty FMEC.

Proceed to the "Test the FMEC Card" section.


Procedure: Test the FMEC Card


Step 1 Replace the suspect card with a known-good card. See "Span Upgrade" section on page 4-24.

Step 2 Resend test traffic on the loopback circuit with a known-good card installed.

Step 3 If the test set indicates a faulty circuit, repeat all of the facility loopback procedures.

Step 4 If the test set indicates a good circuit, the problem is probably the defective FMEC card.

Return the defective card to Cisco through the returned materials authorization (RMA) process. Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Replace the faulty card.

Clear the loopback circuit before testing the next segment of the circuit path.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

Proceed to the "Perform a Hairpin on a Source Node Port" section.


2.2.2 Perform a Hairpin on a Source Node Port

The hairpin circuit test is performed on the cross-connect card in the network circuit. A hairpin circuit uses the same port for both source and destination. Completing a successful hairpin through the card isolates the possibility that the cross-connect card is the cause of the faulty circuit. Figure 2-7 shows an example of a hairpin loopback on a source node port.

Figure 2-7 Hairpin on a source node port


Note The ONS 15454 SDH does not support simplex operation on the cross-connect card. Two cross-connect cards of the same type must be installed for each node.


Procedure: Create the Hairpin on the Source Node


Step 1 Connect an electrical test set to the port you are testing.

a. If you just completed the "Perform a Facility Loopback on a Source E3-12 Port" section, leave the electrical test set hooked up to the E3-12 card.

b. If you are starting the current procedure without the electrical test set hooked up to the E3-12 card, use appropriate cabling to attach the transmit (Tx) and receive (Rx) terminals of the electrical test set to the DSx panel or the FMEC card connectors for the port you are testing. The transmit (Tx) and receive (Rx) terminals connect to the same port.

c. Adjust the test set accordingly.

Step 2 Use CTC to set up the hairpin on the port being tested:

a. Click the Circuits tab and click the Create button.

b. Give the circuit an easily identifiable name, such as hairpin1.

c. Set the Circuit Type and Size to the normal preferences.

d. Uncheck the Bidirectional checkbox and click Next.

e. In the Circuit Source dialog box, select the same Node, card Slot, Port, and Type where the test set is connected and click Next.

f. In the Circuit Destination dialog box, select the same Node, card Slot, Port, and Type used for the Circuit Source dialog box and click Finish.

Step 3 Confirm that the newly created circuit appears on the Circuits tab list as a 1-way circuit.

Step 4 Proceed to the "Test the Hairpin Circuit" section.


Procedure: Test the Hairpin Circuit


Step 1 If the test set is not already sending traffic, send test traffic on the loopback circuit.

Step 2 Examine the test traffic received by the test set. Look for errors or any other signal information that the test set is capable of indicating.

Step 3 If the test set indicates a good circuit, no further testing is necessary with the hairpin circuit.

Clear the hairpin circuit before testing the next segment of the network circuit path.

a. Click the Circuits tab.

b. Choose the hairpin circuit being tested.

c. Click Delete.

d. Click Yes in the Delete Circuits box.

e. Confirm that the hairpin circuit is deleted form the Circuits tab list.

Proceed to the "Perform a Terminal Loopback on a Destination E3-12 Port" section.

Step 4 If the test set indicates a faulty circuit, there may be a problem with the cross-connect card.

Proceed to the "Test the Alternate Cross-Connect Card" section.


Procedure: Test the Alternate Cross-Connect Card


Step 1 Perform a reset on the standby cross-connect card:

a. Determine the standby cross-connect card. On both the physical node and the CTC screen, the ACT/STBY LED of the standby cross-connect card is amber and the ACT/STBY LED of the active cross-connect card is green.

b. Position the cursor over the standby cross-connect card.

c. Right-click to choose RESET CARD.

Step 2 Do a manual switch (side switch) of the cross-connect cards before retesting the loopback circuit:


Caution Cross-connect manual switches (side switches) are service-affecting. Any live traffic on any card in the node endures a hit of up to 50 ms.

a. Determine the standby cross-connect card. The ACT/STBY LED of the standby cross-connect card is amber and the ACT/STBY LED of the active cross-connect card is green.

b. In the node view, select the Maintenance > XC Cards tabs.

c. From the Cross Connect Cards menu, choose Switch.

d. Click Yes in the Confirm Switch dialog box.


Note After the active cross-connect goes into standby, the original standby slot becomes active. This causes the ACT/STBY LED to become green on the former standby card.


Step 3 Resend test traffic on the loopback circuit.

The test traffic now travels through the alternate cross-connect card.

Step 4 If the test set indicates a faulty circuit, assume the cross-connect card is not causing the problem.

Clear the loopback circuit before testing the next segment of the network circuit path.

a. Click the Circuits tab.

b. Choose the hairpin circuit being tested.

c. Click Delete.

d. Click Yes in the Delete Circuits box.

e. Confirm that the hairpin circuit is deleted form the Circuits tab list.

Proceed to the "Perform a Terminal Loopback on a Destination E3-12 Port" section.

Step 5 If the test set indicates a good circuit, the problem may be a defective card.

To confirm a defective original cross-connect card, proceed to the "Retest the Original Cross-Connect Card" section.


Procedure: Retest the Original Cross-Connect Card


Step 1 Do a manual switch (side switch) of the cross-connect cards to make the original cross-connect card the active card.

a. Determine the standby cross-connect card. The ACT/STBY LED of the standby cross-connect card is amber and the ACT/STBY LED of the active cross-connect card is green.

b. In node view, select the Maintenance > XC Cards tabs.

c. From the Cross Connect Cards menu, choose Switch.

d. Click Yes on the Confirm Switch dialog box.

Step 2 Resend test traffic on the loopback circuit.

Step 3 If the test set indicates a faulty circuit, the problem is probably the defective card.

Return the defective card to Cisco through the returned materials authorization (RMA) process. Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Replace the defective cross-connect card. See "Card Replacement" section on page 4-17.

Clear the loopback circuit before testing the next segment of the network circuit path.

a. Click the Circuits tab.

b. Choose the hairpin circuit being tested.

c. Click Delete.

d. Click Yes in the Delete Circuits box.

e. Confirm that the hairpin circuit is deleted form the Circuits tab list.

Proceed to the "Perform a Terminal Loopback on a Destination E3-12 Port" section.

Step 4 If the test set indicates a good circuit, the cross-connect card may have had a temporary problem that was cleared by the side switch.

Clear the loopback circuit before testing the next segment of the network circuit path.

a. Click the Circuits tab.

b. Choose the hairpin circuit being tested.

c. Click Delete.

d. Click Yes in the Delete Circuits box.

e. Confirm that the hairpin circuit is deleted form the Circuits tab list.

Proceed to the "Perform a Terminal Loopback on a Destination E3-12 Port" section.


2.2.3 Perform a Terminal Loopback on a Destination E3-12 Port

The terminal loopback test is performed on the node destination port in the circuit, in this example, the E3-12 port in the destination node. First, create a bidirectional circuit that starts on the source node E3-12 port and loops back on the destination node E3-12 port. Then, proceed with the terminal loopback test. Completing a successful terminal loopback to a destination node E3-12 port verifies that the circuit is good up to the destination E3-12. Figure 2-8 shows an example of a terminal loopback on a destination E3-12 port.

Figure 2-8 Terminal loopback on a destination E3-12 port


Caution Performing a loopback on an in-service circuit is service affecting.

Procedure: Create the Terminal Loopback on a Destination E3-12 Port


Step 1 Connect an electrical test set to the port you are testing:

a. If you are starting the current procedure with the electrical test set hooked up to the E3-12 card in the source node, leave the test set hooked up.

b. If you are starting the current procedure without the electrical test set hooked up to the E3-12 card in the source node, use appropriate cabling to attach the transmit (Tx) and receive (Rx) terminals of the electrical test set to the DSx panel or the FMEC card connectors for the port you are testing. Both transmit (Tx) and receive (Rx) cables connect to the same port.

c. Adjust the test set accordingly.

Step 2 Use CTC to set up the terminal loopback circuit on the port being tested.

a. Click the Circuits tab and click the Create button.

b. Give the circuit an easily identifiable name, such as E312toE312.

c. Set Circuit Type and Size to the normal preferences.

d. Leave the Bidirectional checkbox checked and click Next.

e. In the Circuit Source dialog box, fill in the same Node, card Slot, Port, and Type where the test set is connected and click Next.

f. In the Circuit Destination dialog box, fill in the destination Node, card Slot, Port, and Type (the E3-12 port in the destination node) and click Finish.

Step 3 Confirm that the newly created circuit appears on the Circuits tab list as a 2-way circuit.


Note It is normal for an alarm to appear during a loopback setup. The alarm clears when you remove the loopback.


Step 4 Create the terminal loopback on the destination card and port being tested:

a. Go to the node view of the destination node:

Choose View > Go To Other Node from the menu bar.

Choose the node from the pull-down list in the Select Node box and click OK.

b. In node view, double-click the card that requires the loopback, such as the E3-12 card in the destination node.

c. Click the Maintenance > Loopback tabs.

d. Select OOS_MT from the State column. If this is a multiport card, select the row appropriate for the desired port.

e. Select Terminal (Inward) from the Loopback Type column. If this is a multiport card, select the row appropriate for the desired port.

f. Click Apply.

g. Click Yes in the Confirmation Dialog box.

Step 5 Proceed to the "Test the Terminal Loopback Circuit on the Destination E3-12 Card" section.


Procedure: Test the Terminal Loopback Circuit on the Destination E3-12 Card


Step 1 If the test set is not already sending traffic, send test traffic on the loopback circuit.

Step 2 Examine the test traffic being received by the test set. Look for errors or any other signal information that the test set is capable of indicating.

Step 3 If the test set indicates a good circuit, no further testing is necessary on the loopback circuit.

Clear the terminal loopback before testing the next segment of the network circuit path.

a. Double-click the E3-12 card in the destination node with the terminal loopback.

b. Click the Maintenance > Loopback tabs.

c. Select None from the Loopback Type column for the port being tested.

d. Select the appropriate state (IS, OOS, OOS_AINS) in the State column for the port being tested.

e. Click Apply.

f. Click Yes in the Confirmation Dialog box.

Clear the terminal loopback circuit before testing the next segment of the network circuit path.

a. Click the Circuits tab.

b. Choose the loopback circuit being tested.

c. Click Delete.

d. Click Yes in the Delete Circuits box.

e. Confirm that the loopback circuit is deleted form the Circuits tab list.

Proceed to the "Perform a Facility Loopback on a Destination E3-12 Port" section.

Step 4 If the test set indicates a faulty circuit, the problem may be a faulty card.

Proceed to the "Test the Destination E3-12 Card" section.


Procedure: Test the Destination E3-12 Card


Step 1 Replace the suspect card with a known-good card. See the "Card Replacement" section on page 4-17.

Step 2 Resend test traffic on the loopback circuit with a known-good card.

Step 3 If the test set indicates a good circuit, the problem is probably the defective card.

Return the defective card to Cisco through the returned materials authorization (RMA) process. Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Replace the defective E3-12 card. See the "Card Replacement" section on page 4-17.

Clear the terminal loopback before testing the next segment of the network circuit path.

a. Double-click the E3-12 card in the destination node with the terminal loopback.

b. Click the Maintenance > Loopback tabs.

c. Select None from the Loopback Type column for the port being tested.

d. Select the appropriate state (IS, OOS, OOS_AINS) in the State column for the port being tested.

e. Click Apply.

f. Click Yes in the Confirmation Dialog box.

Clear the terminal loopback circuit before testing the next segment of the network circuit path.

a. Click the Circuits tab.

b. Choose the loopback circuit being tested.

c. Click Delete.

d. Click Yes in the Delete Circuits box.

e. Confirm that the loopback circuit is deleted form the Circuits tab list.

Proceed to the "Perform a Facility Loopback on a Destination E3-12 Port" section.


2.2.4 Perform a Facility Loopback on a Destination E3-12 Port

The facility loopback test is performed on the node source port in the circuit, in this example, the destination E3-12 port in the destination node. Completing a successful facility loopback on this port isolates the possibility that the destination node cabling, E3-12 card, LIU, or FMEC card is responsible for a faulty circuit. Figure 2-9 shows an example of a facility loopback on a destination E3-12 port.

Figure 2-9 Facility loopback on a destination E3-12 port


Caution Performing a loopback on an in-service circuit is service-affecting.

Procedure: Create a Facility Loopback Circuit on a Destination E3-12 Port


Step 1 Connect an electrical test set to the port you are testing:

a. Use appropriate cabling to attach the electrical test set transmit (Tx) and receive (Rx) terminals to the FMEC card connectors or DSx panel for the port you are testing. Both transmit (Tx) and receive (Rx) connect to the same port.

b. Adjust the test set accordingly.

Step 2 Use CTC to create the facility loopback circuit on the port being tested:

a. In node view, double-click the card where the loopback will be performed.

b. Click the Maintenance > Loopback tabs.

c. Select Facility (Line) from the Loopback Type column for the port being tested. If this is a multiport card, select the row appropriate for the desired port.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.


Note It is normal for an alarm to appear during loopback setup. The alarm clears when you remove the loopback.


Step 3 Proceed to the "Test the Facility Loopback Circuit" section.


Procedure: Test the Facility Loopback Circuit


Step 1 If the test set is not already sending traffic, send test traffic on the loopback circuit.

Step 2 Examine the test traffic received by the test set. Look for errors or any other signal information that the test set is capable of indicating.

Step 3 If the test set indicates a good circuit, no further testing is necessary with the loopback circuit.

Clear the facility loopback.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

The entire E3-12 circuit path has now passed its comprehensive series of loopback tests. This circuit qualifies to carry live traffic.

Step 4 If the test set indicates a faulty circuit, the problem may be a faulty E3-12 card, faulty cabling from the E3-12 card to the DSx panel or the FMEC card, or a faulty FMEC card.

Proceed to the "Test the E3-12 Cabling" section.


Procedure: Test the E3-12 Cabling


Step 1 Replace the suspect cabling (the cables from the test set to the DSx panel or the FMEC card ports) with a known-good cable.

If a known-good cable is not available, test the suspect cable with a test set. Remove the suspect cable from the DSx panel or the FMEC card and connect the cable to the transmit (Tx) and receive (Rx) terminals of the test set. Run traffic to determine whether the cable is good or suspect.

Step 2 Resend test traffic on the loopback circuit with a known-good cable installed.

Step 3 If the test set indicates a good circuit, the problem is probably the defective cable.

Replace the defective cable.

Clear the facility loopback.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

The entire E3-12 circuit path has now passed its comprehensive series of loopback tests. This circuit qualifies to carry live traffic.

Step 4 If the test set indicates a faulty circuit, the problem may be a faulty card or a faulty FMEC card.

Proceed to the "Test the E3-12 Card" section.


Procedure: Test the E3-12 Card


Step 1 Replace the suspect card with a known-good card. See the "Card Replacement" section on page 4-17.

Step 2 Resend test traffic on the loopback circuit with a known-good card installed.

Step 3 If the test set indicates a good circuit, the problem was probably the defective card.

Return the defective card to Cisco through the returned materials authorization (RMA) process. Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Replace the faulty card. See the "Card Replacement" section on page 4-17.

Clear the facility loopback.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

The entire E3-12 circuit path has now passed its comprehensive series of loopback tests. This circuit qualifies to carry live traffic.

Step 4 If the test set indicates a faulty circuit, the problem may be a faulty FMEC card.

Proceed to the "Test the FMEC Card" section.


Procedure: Test the FMEC Card


Step 1 Remove and reinstall the FMEC card to ensure a proper seating:

a. Remove the lower backplane cover, loosen the five screws that secure it to the ONS 15454 SDH, and pull it away from the shelf assembly.

b. Loosen the nine perimeter screws that hold the backplane rear cover in place.

c. Lift the FMEC card panel by the bottom to remove it from the shelf assembly.

d. Follow the installation procedure for the appropriate FMEC card.

Step 2 Resend test traffic on the loopback circuit with known-good cabling, a known-good card, and the reinstalled FMEC card.

Step 3 If the test set indicates a good circuit, the problem is probably an improperly seated FMEC card.

Clear the facility loopback.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

The entire E3-12 circuit path has now passed its comprehensive series of loopback tests. This circuit qualifies to carry live traffic.

Step 4 If the test set indicates a faulty circuit, the problem is probably the defective FMEC card.

Return the defective card to Cisco through the returned materials authorization (RMA) process. Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Replace the faulty FMEC card. See the "Card Replacement" section on page 4-17.

Step 5 Resend test traffic on the loopback circuit with known-good cabling, a known-good card, and the replacement FMEC card.

Step 6 If the test set indicates a faulty circuit, repeat all of the facility loopback procedures.

If faulty circuit still persists, contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.

Step 7 If the test set indicates a good circuit, the problem is probably the defective FMEC card.

Clear the facility loopback.

a. Click the Maintenance > Loopback tabs.

b. Choose None from the Loopback Type column for the port being tested.

c. Choose the appropriate state (IS, OOS, OOS_AINS) from the State column for the port being tested.

d. Click Apply.

e. Click Yes in the Confirmation Dialog box.

The entire E3-12 circuit path has now passed its comprehensive series of loopback tests. This circuit qualifies to carry live traffic.


2.3 PC Connectivity Troubleshooting

This section contains troubleshooting procedures for PC and network connectivity to the ONS 15454 SDH.

2.3.1 Unable to Verify the IP Configuration of your PC

Symptom    When connecting your PC to the ONS 15454 SDH, you are unable to successfully ping the IP address of your PC to verify the IP configuration.

Table 2-1 describes the potential cause(s) of the symptom and the solution(s).

Table 2-1 Unable to Verify the IP Configuration of your PC 

Possible Problem
Solution

The IP address was typed incorrectly.

Verify that the IP address used to ping the PC matches the IP address displayed when in the Windows IP Configuration information retrieved from the system. Refer to the "Verify the IP Configuration of your PC" section.

The IP configuration of your PC is not properly set.

To verify the IP configuration of your PC, refer to the "Verify the IP Configuration of your PC" section. If this procedure is unsuccessful, contact your Network Administrator for instructions to correct the IP configuration of your PC.


Procedure: Verify the IP Configuration of your PC


Step 1 Open a DOS command window by selecting Start > Run from the Start menu.

Step 2 In the Run window open field, type command and then click the OK button. The DOS command window will appear.

Step 3 At the prompt in the DOS window, type one of the following appropriate commands:

For Windows 98, NT, and 2000, type ipconfig and press the Enter key.

For Windows 95, type winipcfg and press the Enter key.

The Windows IP configuration information will be displayed, including the IP address, Subnet Mask, and the Default Gateway.

Step 4 At the prompt in the DOS window, type ping followed by the IP address shown in the Windows IP configuration information previously displayed.

Step 5 Press the Enter key to execute the command.

If the DOS window displays multiple (usually four) replies, the IP configuration is working properly.

If you do not receive a reply, your IP configuration may not be properly set. Contact your Network Administrator for instructions to correct the IP configuration of your PC.


2.3.2 Browser Login Does Not Launch Java

Symptom    The message "Loading Java Applet" does not appear and the JRE does not launch during the initial login.

Table 2-2 describes the potential cause(s) of the symptom and the solution(s).

Table 2-2 Browser Login Does Not Launch Java 

Possible Problem
Solution

The PC operating system and browser are not properly configured.

Reconfigure the PC operating system java plug-in control panel and the browser settings.

See the "Reconfigure the PC Operating System Java Plug-in Control Panel" section and the "Reconfigure the Browser" section.


Procedure: Reconfigure the PC Operating System Java Plug-in Control Panel


Step 1 From the Windows start menu, click Settings > Control Panel.

Step 2 If Java Plug-in Control Panel does not appear, the JRE may not be installed on your PC.

a. Run the Cisco ONS 15454 SDH software CD.

b. Open the [CD drive]:\Windows\JRE folder.

c. Double-click the j2re-1_3_1_02-win icon to run the JRE installation wizard.

d. Follow the JRE installation wizard steps.

Step 3 From the Windows start menu, click Settings > Control Panel.

Step 4 In the Java Plug-in Control Panel window, double-click the Java Plug-in 1.3.1_02 icon.

Step 5 Click the Advanced tab on the Java Plug-in Control Panel.

Step 6 From the Java Run Time Environment menu, select JRE 1.3 in C:\ProgramFiles\JavaSoft\JRE\1.3.1_02.

Step 7 Click the Apply button.

Step 8 Close the Java Plug-in Control Panel window.


Procedure: Reconfigure the Browser


Step 1 From the Start Menu, launch your browser application.

Step 2 If you are using Netscape Navigator:

a. On the Netscape Navigator menu bar, click the Edit > Preferences menus.

b. In the Preferences window, click the Advanced > Proxies categories.

c. In the Proxies window, click the Direct connection to the Internet checkbox and click the OK button.

d. On the Netscape Navigator menu bar, click the Edit > Preferences menus.

e. In the Preferences window, click the Advanced > Cache categories.

f. Confirm that the Disk Cache Folder field shows one of the following paths:

g. For Windows 95/98/ME, C:\ProgramFiles\Netscape\Communicator\cache

h. For Windows NT/2000, C:\ProgramFiles\Netscape\<username>\Communicator\cache.

i. If the Disk Cache Folder field is not correct, click the Choose Folder button.

j. Navigate to the file listed in f. and click the OK button.

k. Click the OK button on the Preferences window and exit the browser.

Step 3 If you are using Internet Explorer:

a. On the Internet Explorer menu bar, click the Tools > Internet Options menus.

b. In the Internet Options window, click the Advanced tab.

c. In the Settings menu, scroll down to Java (Sun) and click the Use Java 2 v1.3.1_02 for <applet> (requires restart) checkbox.

d. Click the OK button in the Internet Options window and exit the browser.

Step 4 Temporarily disable any virus-scanning software on the computer. See the "Browser Stalls When Downloading CTC JAR Files From TCC-I" section.

Step 5 Verify that the computer does not have two network interface cards (NICs) installed. If the computer does have two NICs, remove one.

Step 6 Restart the browser and logon to the ONS 15454 SDH.


2.3.3 Unable to Verify the NIC Connection on your PC

Symptom    When connecting your PC to the ONS 15454 SDH, you are unable to verify the NIC connection is working properly because the link LED is not illuminated or flashing.

Table 2-3 describes the potential cause(s) of the symptom and the solution(s).

Table 2-3 Unable to Verify the NIC Connection on your PC 

Possible Problem
Solution

The Category 5 cable is not plugged in properly.

Confirm both ends of the cable are properly inserted. If the cable is not fully inserted due to a broken locking clip, the cable should be replaced.

The Category 5 cable is damaged.

Ensure that the cable is in good condition. If in doubt, use a known-good cable. Often, cabling is damaged due to pulling or bending

Incorrect type of Category 5 cable is being used.

If connecting an ONS 15454 SDH directly to your laptop/PC or a router, use a straight-through Category 5 cable. When connecting the ONS 15454 SDH to a hub or a LAN switch, use a crossover Category 5 cable.

For details on the types of Category 5 cables, see the "Crimp Replacement Category 5 Cables" section.

The NIC is improperly inserted or installed.

If you are using a PCMCIA based NIC, remove and re-insert the NIC to make sure the NIC is fully inserted.

If the NIC is built into the laptop/PC, verify that the NIC is not faulty.

The NIC is faulty.

Confirm that the NIC is working properly. If you have no issues connecting to the network (or any other node), then the NIC should be working correctly.

If you have difficulty connecting to the network (or any other node), then the NIC may be faulty and needs to be replaced.


2.3.4 Verify PC Connection to the ONS 15454 SDH (ping)

Symptom    The TCP/IP connection was established and then lost, and a DISCONNECTED alarm appears on CTC.

Table 2-4 describes the potential cause(s) of the symptom and the solution(s).

Table 2-4 Verify PC connection to ONS 15454 SDH (ping) 

Possible Problem
Solution

A lost connection between the PC and the ONS 15454 SDH.

Use a standard ping command to verify the TCP/IP connection between the PC and the ONS 15454 SDH TCC-I card. A ping command will work if the PC connects directly to the TCC-I card or uses a LAN to access the TCC-I card.

See the "Ping the ONS 15454 SDH" section.


Procedure: Ping the ONS 15454 SDH


Step 1 Display the command prompt:

a. If you are using a Microsoft Windows operating system, from the Start Menu choose Run, type command prompt in the Open field of the Run dialog box, and click OK.

b. If you are using a Sun Solaris operating system, from the Common Desktop Environment (CDE) click the Personal Application tab and click Terminal.

Step 2 For both the Sun and Microsoft operating systems, at the prompt type:

ping [ONS 15454 SDH IP address]  
For example, ping 192.1.0.2.

Step 3 If the workstation has connectivity to the ONS 15454 SDH, the ping is successful and displays a reply from the IP address. If the workstation does not have connectivity, a "Request timed out" message displays.

Step 4 If the ping is successful, an active TCP/IP connection exists. Restart CTC.

Step 5 If the ping is not successful, and the workstation connects to the ONS 15454 SDH through a LAN, check that the workstation's IP address is on the same subnet as the ONS node.

Step 6 If the ping is not successful and the workstation connects directly to the ONS 15454 SDH, check that the link light on the workstation's NIC is illuminated.


2.4 CTC Operation Troubleshooting

This section contains troubleshooting procedures for CTC login or operation problems.

2.4.1 Browser Stalls When Downloading CTC JAR Files From TCC-I

Symptom    The browser stalls or hangs when downloading a CTC JAR file from the TCC-I card.

Table 2-5 describes the potential cause(s) of the symptom and the solution(s).

Table 2-5 Browser Stalls When Downloading jar File From TCC-I 

Possible Problem
Solution

McAfee VirusScan software may be interfering with the operation. The problem occurs when the VirusScan Download Scan is enabled on McAfee VirusScan 4.5 or later.

Disable the VirusScan Download Scan feature. See the "Disable the VirusScan Download Scan" section.


Procedure: Disable the VirusScan Download Scan


Step 1 From the Windows start menu, choose Programs > Network Associates > VirusScan Console.

Step 2 Double-click the VShield icon listed in the VirusScan Console dialog box.

Step 3 Click the Configure button on the lower part of the Task Properties window.

Step 4 Click the Download Scan icon on the left of the System Scan Properties dialog box.

Step 5 Uncheck the Enable Internet download scanning checkbox.

Step 6 Click Yes when the warning message appears.

Step 7 Click OK on the System Scan Properties dialog box.

Step 8 Click OK on the Task Properties window.

Step 9 Close the McAfee VirusScan window.


2.4.2 CTC Does Not Launch

Symptom    CTC does not launch, usually an error message appears before the login screen displays.

Table 2-6 describes the potential cause(s) of the symptom and the solution(s).

Table 2-6 CTC Does Not Launch 

Possible Problem
Solution

The Netscape browser cache may point to an invalid directory.

Redirect the Netscape cache to a valid directory. See the "Redirect the Netscape Cache to a Valid Directory" section.


Procedure: Redirect the Netscape Cache to a Valid Directory


Step 1 Launch Netscape.

Step 2 Display the Edit menu.

Step 3 Choose Preferences.

Step 4 Under the Category column on the left-hand side, go to Advanced and choose the Cache tab.

Step 5 Change your disk cache folder to point to the cache file location.

The cache file location is usually C:\ProgramFiles\Netscape\Users\<yourname>\cache. The <yourname> segment of the file location is often the same as the user name.


2.4.3 Sluggish CTC Operation or Login Problems

Symptom    You experience sluggish CTC operation or have problems logging into CTC.

Table 2-7 describes the potential cause(s) of the symptom and the solution(s).

Table 2-7 Sluggish CTC Operation or Login Problems 

Possible Problem
Solution

The CTC cache file may be corrupted or may need to be replaced.

Delete the CTC cache file. This operation forces the ONS 15454 SDH to download a new set of jar files to your computer hard drive. See the "Delete the CTC Cache File Automatically" section or the "Delete the CTC Cache File Manually" section.


Procedure: Delete the CTC Cache File Automatically


Step 1 Enter an ONS 15454 SDH IP address into the browser URL field. The initial browser window shows a Delete CTC Cache button.

Step 2 Close all open CTC sessions and browser windows. The PC operating system will not allow you to delete files that are in use.

Step 3 Click the Delete CTC Cache button on the initial browser window to clear the CTC cache. Figure 2-10 shows the Delete CTC Cache screen.


Note For CTC cache file manual deletion, see the "Delete the CTC Cache File Manually" section.


Figure 2-10 Deleting the CTC cache


Procedure: Delete the CTC Cache File Manually


Step 1 To delete the jar files manually, from the Windows Start menu choose Search > For Files or Folders.

Step 2 Enter *.jar in the Search for files or folders named field on the Search Results dialog box and click Search Now.

Step 3 Click the Modified column on the Search Results dialog box to find the jar files that match the date when you downloaded the files from the TCC-I. These files may include CTC*.jar, CMS*.jar, and jar_cache*.tmp.

Step 4 Highlight the files and press the keyboard Delete key.

Step 5 Click Yes at the Confirm dialog box.


2.4.4 Node Icon is Grey on CTC Network View

Symptom    The CTC network view shows one or more node icons as grey in color and without a node name.

Table 2-8 describes the potential cause(s) of the symptom and the solution(s).

Table 2-8 Node Icon is Grey on CTC Network View 

Possible Problem
Solution

Different CTC releases not recognizing each other.

Usually accompanied by an INCOMPATIBLE-SW alarm. Correct the core version build as described in the "Different CTC Releases Do Not Recognize Each Other" section.

A username/password mismatch.

Usually accompanied by a NOT-AUTHENTICATED alarm. Correct the username and password as described in the "Username or Password Does Not Match" section.

No IP connectivity between nodes.

Usually accompanied by Ethernet-specific alarms. Verify the Ethernet connections as described in the "Ethernet Connections" section.

A lost DCC connection.

Usually accompanied by an EOC alarm. Clear the EOC alarm and verify the DCC connection as described in the "Clear the EOC Alarm" procedure on page 1-42.


2.4.5 CTC Cannot Launch Due to Applet Security Restrictions

Symptom    The error message "Unable to launch CTC due to applet security restrictions" appears after you enter the IP address in the browser window.

Table 2-9 describes the potential cause(s) of the symptom and the solution(s).

Table 2-9 CTC Cannot Launch Due to Applet Security Restrictions 

Possible Problem
Solution

Did not execute the javapolicyinstall.bat file, or the java.policy file may be incomplete.

1. Verify that you have executed the javapolicyinstall.bat file on the ONS 15454 SDH software CD. This file is installed when you run the CTC Setup Wizard (refer to the CTC installation information in the Cisco ONS 15454 SDH Installation and Operations Guide for instructions).

2. If you ran the javapolicyinstall.bat file but still receive the error message, you must manually edit the java.policy file on your computer. See the "Manually Edit the java.policy File" section.


Procedure: Manually Edit the java.policy File


Step 1 Search your computer for this file and open it with a text editor (Notepad or Wordpad).

Step 2 Verify that the end of this file has the following lines:

		// Insert this into the system-wide or a per-user java.policy file.
	// DO NOT OVERWRITE THE SYSTEM-WIDE POLICY FILE--ADD THESE LINES!

	grant codeBase "http://*/fs/LAUNCHER.jar" {
permission java.security.AllPermission;
	};

Step 3 If these five lines are not in the file, enter them manually.

Step 4 Save the file and restart Netscape.

CTC should now start correctly.

Step 5 If the error message is still reported, save the java.policy file as (.java.policy). On Win95/98/2000 PCs, save the file to the C:\Windows folder. On WinNT4.0 PCs, save the file to all of the user folders on that PC, for example, C:\Winnt\profiles\joeuser.


2.4.6 Java Runtime Environment Incompatible

Symptom    The CTC application will not run properly.

Table 2-10 describes the potential cause(s) of the symptom and the solution(s).

Table 2-10 Java Runtime Environment Incompatible 

Possible Problem
Solution

Do not have the compatible Java 2 JRE installed.

The Java 2 Runtime Environment (JRE) contains the Java virtual machine, runtime class libraries, and Java application launcher that are necessary to run programs written in the Java programming language.

The ONS 15454 SDH CTC is a Java application. A Java application, unlike an applet, cannot rely completely on a web browser for installation and runtime services. When you run an application written in the Java programming language, you need the correct JRE installed. The correct JRE for each CTC software release is included on the Cisco ONS 15454 SDH software CD and on the Cisco ONS 15454 SDH documentation CD. See the "Launch CTC to Correct the Core Version Build" section.

If you are running multiple CTC software releases on a network, the JRE installed on the computer must be compatible with the different software releases. Table 2-11 shows JRE compatibility with ONS 15454 SDH software releases.


Table 2-11 JRE Compatibility 

ONS Software Release
JRE 1.2.2 Compatible
JRE 1.3 Compatible

ONS 15454 SDH Release 3.3

Yes

Yes

ONS 15454 SDH Release 3.4

No

Yes


Procedure: Launch CTC to Correct the Core Version Build


Step 1 Exit the current CTC session.

Step 2 Click the Delete CTC Cache button in the browser window ( Figure 2-10).

Step 3 Completely close the browser.

Step 4 Start the browser.

Step 5 Type the ONS 15454 SDH IP address and click Go. This can be the original IP address you logged on with or an IP address other than the original.

Step 6 Log into CTC. The browser will download the jar file from CTC.


Note The .jar files consist of core and element files. Core files are common to the ONS 15454 SDH, ONS 15454 SONET, and ONS 15327, while the element files are unique to the particular product. For example, the ONS 15454 SDH Release 1.0 uses a 3.3 core build and a 1.0 element build. To display the CTC Core Version number, from the CTC menu bar click Help > About CTC. This lists the Core and Element builds discovered on the network.



2.4.7 Different CTC Releases Do Not Recognize Each Other

Symptom    This situation is often accompanied by the INCOMPATIBLE-SW alarm.

Table 2-12 describes the potential cause(s) of the symptom and the solution(s).

Table 2-12 Different CTC Releases Do Not Recognize Each Other 

Possible Problem
Solution

The software loaded on the connecting workstation and the software on the TCC-I card are incompatible.

This occurs when the TCC-I software is upgraded but the PC has not yet upgraded the compatible CTC jar file. It also occurs on login nodes with compatible software that encounter other nodes in the network that have a newer software version.

Note Remember to always logon to the ONS node with the latest CTC core version first. If you initially log into an ONS node running a CTC core version of 3.3 and then attempt to log into another ONS node in the network running a higher CTC core version, the lower version node will not recognize the new node.

See the "Launch CTC to Correct the Core Version Build" section.


Procedure: Launch CTC to Correct the Core Version Build


Step 1 Exit the current CTC session.

Step 2 Click the Delete CTC Cache button in the browser window ( Figure 2-10).

Step 3 Completely close the browser.

Step 4 Start the browser.

Step 5 Type the ONS 15454 SDH IP address and click Go. This can be the original IP address you logged on with or an IP address other than the original.

Step 6 Log into CTC. The browser will download the jar file from CTC.


Note The .jar files consist of core and element files. Core files are common to the ONS 15454 SDH, ONS 15454 SONET, and ONS 15327, while the element files are unique to the particular product. For example, the ONS 15454 SDH Release 1.0 uses a 3.3 core build and a 1.0 element build. To display the CTC Core Version number, from the CTC menu bar click Help > About CTC. This lists the Core and Element builds discovered on the network.



2.4.8 Username or Password Does Not Match

Symptom    A mismatch often occurs concurrently with a NOT-AUTHENTICATED alarm.

Table 2-13 describes the potential cause(s) of the symptom and the solution(s).

Table 2-13 Username or Password Do Not Match 

Possible Problem
Solution

The username or password entered do not match the information stored in the TCC-I.

All ONS nodes must have the same username and password created to display every ONS node in the network. You can also be locked out of certain ONS nodes on a network if your username and password were not created on those specific ONS nodes.

For initial logon to the ONS 15454 SDH, type the CISCO15 user name in capital letters and click Login (no password is required).

See the "Verify Correct Username and Password" section.


Procedure: Verify Correct Username and Password


Step 1 Ensure that your keyboard Caps Lock key is not turned on and affecting the case-sensitive entry of the username and password.

Step 2 Contact your system administrator to verify the username and password.

Step 3 Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Have Cisco TAC enter your system and create a new user name and password.


2.4.9 No IP Connectivity Exists Between Nodes

Symptom    The nodes have a grey icon and is usually accompanied by alarms.

Table 2-14 describes the potential cause(s) of the symptom and the solution(s).

Table 2-14 No IP Connectivity Exists Between Nodes 

Possible Problem
Solution

A lost Ethernet connection.

Usually is accompanied by Ethernet-specific alarms. Verify the Ethernet connections as described in the "Ethernet Connections" section.


2.4.10 DCC Connection Lost

Symptom    The node is usually accompanied by alarms and the nodes in the network view have a grey icon. This symptom is usually accompanied by an EOC alarm.

Table 2-15 describes the potential cause(s) of the symptom and the solution(s).

Table 2-15 DCC Connection Lost 

Possible Problem
Solution

A lost DCC connection.

Usually accompanied by an EOC alarm. Clear the EOC alarm and verify the DCC connection as described in the "Clear the EOC Alarm" procedure on page 1-42.


2.4.11 "Path in Use" Error When Creating a Circuit

Symptom    While creating a circuit, you get a "Path in Use" error that prevents you from completing the circuit creation.

Table 2-16 describes the potential cause(s) of the symptom and the solution(s).

Table 2-16 "Path in Use" error when creating a circuit 

Possible Problem
Solution

Another user has already selected the same source port to create another circuit.

CTC does not remove a card or port from the available list until a circuit is completely provisioned. If two users simultaneously select the same source port to create a circuit, the first user to complete circuit provisioning will get use of the port. The other user will get the "Path in Use" error.

Cancel the circuit creation and start over, or click the Back button until you return to the initial circuit creation screen. The source port that was previously selected will no longer appear in the available list because it is now part of a provisioned circuit. Select a different available port and begin the circuit creation process again.


2.4.12 Calculate and Design IP Subnets

Symptom    You cannot calculate or design IP subnets on the ONS 15454 SDH.

Table 2-17 describes the potential cause(s) of the symptom and the solution(s).

Table 2-17 Calculate and Design IP Subnets 

Possible Problem
Solution

The IP capabilities of the ONS 15454 SDH require specific calculations to properly design IP subnets.

Cisco provides a free online tool to calculate and design IP subnets. Go to http://www.cisco.com/techtools/ip_addr.html. For information about ONS 15454 SDH IP capability, refer to the Cisco ONS 15454 SDH Installation and Operations Guide.


2.4.13 Ethernet Connections

Symptom    Ethernet connections appear to be broken or are not working properly.

Table 2-18 describes the potential cause(s) of the symptom and the solution(s).

Table 2-18 Calculate and Design IP Subnets 

Possible Problem
Solution

Improperly seated connections.

You can fix most connectivity problems in an Ethernet network by following a few guidelines. See Figure 2-11 when consulting the steps in the "Verify Ethernet Connections" section.

Incorrect connections.


Figure 2-11 Ethernet connectivity reference

Procedure: Verify Ethernet Connections


Step 1 Check for SONET alarms on the STS-N that carries the VLAN #1 Ethernet circuit. Clear any alarms by looking them up in Chapter 1, "Alarm Troubleshooting."

Step 2 Check for Ethernet-specific alarms. Clear any raised alarms by looking up that alarm in Chapter 1, "Alarm Troubleshooting."

Step 3 Verify that the ACT LED on the Ethernet card is green.

Step 4 Verify that Ports 1 and 3 on ONS 15454 SDH #1 and Ports 1 and 2 on ONS 15454 SDH #2 have green link-integrity LEDs illuminated.

Step 5 If no green link-integrity LED is illuminated for any of these ports:

a. Verify physical connectivity between the ONS 15454 SDHs and the attached device.

b. Verify that the ports are enabled on the Ethernet cards.

c. Verify that you are using the proper Ethernet cable and that it is wired correctly, or replace the cable with a known-good Ethernet cable.

d. Check the status LED on the Ethernet card faceplate to ensure the card booted up properly. This LED should be steady green. If necessary, remove and reinsert the card and allow it to reboot.

e. It is possible that the Ethernet port is functioning properly but the link LED itself is broken. Run the procedure in the "Lamp Test for Card LEDs" section.

Step 6 Verify connectivity between device A and device C by pinging between these locally attached devices (see the "Verify PC Connection to the ONS 15454 SDH (ping)" section). If the ping is unsuccessful:

a. Verify that device A and device C are on the same IP subnet.

b. Display the Ethernet card in CTC card view and click the Provisioning > VLAN tabs to verify that both Port 1 and Port 3 on the card are assigned to the same VLAN.

c. If a port is not assigned to the correct VLAN, click that port column in the VLAN row and set the port to Tagged or Untag. Click Apply.

Step 7 Repeat Step 6 for devices B and D.

Step 8 Verify that the Ethernet circuit that carries VLAN #1 is provisioned and that ONS 15454 SDH #1 and ONS 15454 SDH #2 ports also use VLAN #1.


2.4.14 VLAN Cannot Connect to Network Device from Untag Port

Symptom    Networks that have a VLAN with one ONS 15454 SDH Ethernet card port set to Tagged and one ONS 15454 SDH Ethernet card set to Untag may have difficulty implementing Address Resolution Protocol (ARP) for a network device attached to the Untag port ( Figure 2-12). They may also see a higher than normal runt packets count at the network device attached to the Untag port.

Figure 2-12 A VLAN with Ethernet ports at Tagged and Untag

Table 2-19 describes the potential cause(s) of the symptom and the solution(s).

Table 2-19 Verify PC connection to ONS 15454 SDH (ping) 

Possible Problem
Solution

The Tagged ONS 15454 SDH adds the 802.1Q tag and the Untag ONS 15454 SDH removes the Q-tag without replacing the bytes. The NIC of the network device categorizes the packet as a runt and drops the packet.

The solution is to set both ports in the VLAN to Tagged to stop the stripping of the 4 bytes from the data packet and prevents the NIC card in the network access device from recognizing the packet as a runt and dropping it. Network devices with 802.1Q-compliant NIC cards will accept the tagged packets. Network devices with non-802.1Q compliant NIC cards will still drop these tagged packets. The solution may require upgrading network devices with non-802.1Q compliant NIC cards to 802.1Q-compliant NIC cards. You can also set both ports in the VLAN to Untag, but you will lose 802.1Q compliance.

Dropped packets can also occur when ARP attempts to match the IP address of the network device attached to the Untag port with the physical MAC address required by the network access layer.


Procedure: Change VLAN Port Tag and Untagged Settings


Step 1 Display the CTC card view for the Ethernet card involved in the problem VLAN.

Step 2 Click the Provisioning > VLAN tabs ( Figure 2-13).

Figure 2-13 Configuring VLAN membership for individual Ethernet ports

Step 3 If the port is set to Tagged, continue to look at other cards and their ports in the VLAN until you find the port that is set to Untag.

Step 4 At the VLAN port set to Untag, click the port and choose Tagged.


Note The attached external devices must recognize IEEE 802.1Q VLANs.


Step 5 After each port is in the appropriate VLAN, click Apply.


2.4.15 Cross-Connect Card Oscillator Fails

Symptom: The XC10G card can be affected by this problem. It is indicated by a CTNEQPT-PBPROT or CTNEQPT-PBWORK condition raised against all I/O cards in the node. The following conditions might also be raised on the node:

SWMTXMOD against one or both cross-connect cards

SDBER-EXCEED-LO against near-end or far-end line cards

MS-AIS against far-end line cards

LP-RFI against near-end line cards

Table 2-20 describes the potential cause(s) of the symptom and the solution(s).

Table 2-20 Cross-Connect Card Oscillator Fails 

Possible Problem
Solution

The XC10G card has oscillator failure.

1. If the Slot 8 cross-connect card is active, see the "Resolve the XC Oscillator Failure When Slot 8 XC Card is Active" section.

2. If the Slot 10 cross-connect card is active, see the "Resolve the XC Oscillator Failure When Slot 10 XC Card is Active" section.


Procedure: Resolve the XC Oscillator Failure When Slot 8 XC Card is Active


Step 1 If the CTNEQPT-PBPROT condition is reported against all I/O cards in the node and the Slot 8 cross-connect card is active, right-click the Slot 10 cross-connect card.

Step 2 Choose Reset Card, then click OK. (Slot 8 remains active and Slot 10 remains standby.)

Step 3 If the alarm remains, reseat the Slot 10 card.

Step 4 If CTNEQPT-PBPROT does not clear, replace the Slot 10 cross-connect card with a spare card.

Step 5 If CTNEQPT-PBPROT does not clear, replace the spare card placed in Slot 10 with the original cross-connect card.

Step 6 Right-click the Slot 8 card and choose Reset Card.

Step 7 Click OK to activate the Slot 10 card and place the Slot 8 card in standby.

Step 8 If you then see the CTNEQPT-PBWORK condition raised against all I/O cards in the node, verify that CTNEQPT-PBPROT has cleared on all I/O cards. Seeing CTNEQPT-PBWORK on the cards indicates that Slot 8 card has a bad oscillator. If this is indicated, complete the following substeps. Otherwise, go to Step 9.

a. Replace the Slot 8 cross-connect card with a spare card. (Slot 8 remains standby.)

b. Reseat the Slot 10 cross-connect card to activate the Slot 8 card and make Slot 10 standby.

c. Verify that the CTNEQPT-PBWORK condition has cleared on all I/O cards.

Step 9 If you see CTNEQPT-PBPROT reported against all I/O cards in the node, this indicates that the Slot 10 card has a bad oscillator. If so, complete the following steps:

a. Replace the Slot 10 cross-connect card with a spare card. (The Slot 8 card is now active.)

b. Reseat the Slot 8 cross-connect card to make Slot 10 active.

c. Verify that the CTNEQPT-PBPROT condition has cleared on all I/O cards.


Procedure: Resolve the XC Oscillator Failure When Slot 10 XC Card is Active


Step 1 If the CTNEQPT-PBWORK condition is reported against all I/O cards in the node and the Slot 10 card is active, right-click the Slot 8 cross-connect card.

Step 2 Choose Reset Card and click OK. (Slot 10 remains active and Slot 8 remains standby.)

Step 3 If the CTNEQPT-PBWORK condition does not clear, reseat the Slot 8 cross-connect card.

Step 4 If the condition does not clear, replace the Slot 8 cross-connect card with an identical, spare card.

Step 5 If the condition does not clear, replace the spare card placed in Slot 8 with the original cross-connect card.

Step 6 Right-click the Slot 10 cross-connect card.

Step 7 Choose Reset Card and click OK. The Slot 8 cross-connect card becomes active and Slot 10 becomes standby.

Step 8 If you have switched the Slot 8 card to active and continue to see CTNEQPT-PBWORK reported against all I/O cards in the node, this indicates the Slot 8 card has a bad oscillator. If this is indicated, complete the following substeps. If not, go to Step 9.

a. Replace the Slot 8 cross-connect card with a spare card. (The Slot 10 card is made active.)

b. Reseat the Slot 10 cross-connect card to make Slot 8 active.

c. Verify that the CTNEQPT-PBWORK condition has cleared on all I/O cards.

Step 9 If you then see the CTNEQPT-PBPROT condition raised against all I/O cards, verify that CTNEQPT-PBWORK has cleared on the I/O cards. This indicates that Slot 10 has a bad oscillator. If so, complete the following substeps:

a. Replace the Slot 10 cross-connect card with a spare card. (Slot 10 remains standby.)

b. Reseat the Slot 8 cross-connect card to activate the Slot 10 card and make Slot 8 standby.

c. Verify that the CTNEQPT-PBPROT condition has cleared on all I/O cards.


2.5 Circuits and Timing

This section provides solutions to circuit creation and reporting errors, as well as common timing reference errors and alarms.

2.5.1 Circuit Transitions to Partial State

Symptom    An automatic or manual transition of a circuit from one state to another state results in one of the following partial state conditions:

OOS_PARTIAL  At least one of the connections in the circuit is in OOS state and at least one other connection in the circuit is in IS, OOS_MT, or OOS_AINS state.

OOS_MT_PARTIAL  At least one connection in the circuit is in OOS_MT state and at least one other connection in the circuit is in IS, OOS_MT, or OOS_AINS state.

OOS_AINS_PARTIAL  At least one connection in the circuit is in the OOS_AINS state and at least one other connection in the circuit is in IS or OOS_AINS state.

Table 2-21 describes the potential cause(s) of the symptom and the solution(s).

Table 2-21 Circuit in Partial State 

Possible Problem
Solution

During a manual transition, CTC cannot communicate with one of the nodes or one of the nodes is on a version of software that does not support the new state model.

Repeat the manual transition operation. If the partial state persists, determine which node in the circuit is not changing to the desired state. Refer to the "View the State of Circuit Nodes" section.

Logon to the circuit node that did not change to the desired state and determine the version of software. If the software on the node is a version earlier than 3.4, upgrade the software. Refer to the Cisco ONS 15454 Software Upgrade Guide for software upgrade procedures.

Note If the node software cannot be upgraded to version 3.4, the partial state condition can be avoided by only using the circuit state(s) supported in the earlier software version.

During an automatic transition, some path-level defects and/or alarms were detected on the circuit.

Determine which node in the circuit is not changing to the desired state. Refer to the "View the State of Circuit Nodes" section.

Logon to the circuit node that did not change to the desired state and examine the circuit for path-level defects, improper circuit termination, or alarms. Refer to the Cisco ONS 15454 SDH Installation and Operations Guide for procedures to clear alarms and change circuit configuration settings.

Resolve and clear the defects and/or alarms on the circuit node and verify that the circuit transitions to the desired state.

One end of the circuit is not properly terminated.


Procedure: View the State of Circuit Nodes


Step 1 Click the Circuits tab.

Step 2 From the Circuits tab list, select the circuit with the *_PARTIAL state condition.

Step 3 Click the Edit button. The Edit Circuit window appears.

Step 4 In the Edit Circuit window, click the State tab.

The State tab window will list the Node, CRS End A, CRS End B, and CRS State for each of the nodes in the circuit.


2.5.2 TU-AIS on Unused VC Circuits

Symptom    An incomplete circuit path causes a tributary unit alarm indications signal (TU-AIS).

Table 2-22 describes the potential cause(s) of the symptom and the solution(s).

Table 2-22 TU-AIS on Unused VC Circuits 

Possible Problem
Solution

The port on the reporting node is in-service but a node upstream on the circuit does not have an STM-N port in service.

A TU-AIS indicates that an upstream failure occurred at the virtual channel (VC) layer. TU-AIS alarms also occur on VC circuits that are not carrying traffic and on stranded bandwidth.

Perform the "Clear TU-AIS on Unused VC Circuits" section.


Procedure: Clear TU-AIS on Unused VC Circuits


Step 1 Determine the affected port.

Step 2 Record the node ID, slot number, port number, or VC number.

Step 3 Create a unidirectional VC circuit from the affected port back to itself, such as Source node/Slot 2/Port 2/VC11 cross connected to Source node/Slot 2/Port 2/VC11.

Step 4 Uncheck the bidirectional box in the circuit creation window.

Step 5 Give the unidirectional VC circuit an easily recognizable name, such as delete me.

Step 6 Display the DS3IN card in CTC card view. Click the Maintenance > DS1 tabs.

Step 7 Locate the VC that is reporting the alarm (for example, DS3 #2, DS1 #13).

Step 8 From the Loopback Type list, choose Facility (line) and click Apply.

Step 9 Click Circuits.

Step 10 Find the one-way circuit you created in Step 2. Select the circuit and click Delete.

Step 11 Click Yes in the Delete Confirmation box.

Step 12 Display the DS3IN card in CTC card view. Click Maintenance > DS1.

Step 13 Locate the VC in Facility (line) Loopback.

Step 14 From the Loopback Type list, choose None and then click Apply.

Step 15 Click the Alarm tab and verify that the TU-AIS alarms have cleared.

Step 16 Repeat this procedure for all the TU-AIS alarms on the DS3IN cards.


2.5.3 Circuit Creation Error with VC Circuit

Symptom    You might receive an "Error while finishing circuit creation. Unable to provision circuit. Unable to create connection object at <node name>" message when trying to create a VC circuit in CTC.

Table 2-23 describes the potential cause(s) of the symptom and the solution(s).

Table 2-23 Circuit Creation Error with VC Circuit 

Possible Problem
Solution

You may have run out of bandwidth on the VC cross-connect matrix at the ONS 15454 SDH indicated in the error message.

The matrix has a maximum capacity of 336 bidirectional VC cross-connects. Certain configurations will exhaust VC capacity with less than 336 bidirectional VCs in a MS-SPRing or less than 224 bidirectional VCs in SNCP or 1+1 protection. Refer to the Cisco ONS 15454 SDH Installation and Operations Guide for more information.


2.5.4 ONS 15454 SDH Switches Timing Reference

Symptom    Timing references switch when one or more problems occur.

Table 2-24 describes the potential cause(s) of the symptom and the solution(s).

Table 2-24 ONS 15454 SDH Switches Timing Reference 

Possible Problem
Solution

The optical or SETS input is receiving loss of signal (LOS), loss of frame (LOF), or AIS alarms from its timing source.

The ONS 15454 SDH internal clock operates at a Stratum 3 level of accuracy. This gives the ONS 15454 SDH a free-running synchronization accuracy of ± 4.6 ppm and a holdover stability of less than 255 slips in the first 24 hours or 3.7x10-7/day, including temperature.

ONS 15454 SDH free-running synchronization relies on the Stratum 3 internal clock. Over an extended time period, using a higher quality Stratum 1 or Stratum 2 timing source results in fewer timing slips than a lower quality Stratum 3 timing source.

The optical or SETS input is not functioning.

Sync Status Messaging (SSM) message is set to Don't Use for Sync (DUS).

SSM indicates a Stratum 3 or lower clock quality.

The input frequency is off by more than 15 ppm.

The input clock wanders and has more than three slips in 30 seconds.

A bad timing reference existed for at least two minutes.


2.5.5 Holdover Synchronization Alarm

Symptom    The clock is running at a different frequency than normal and the HLDOVRSYNC alarm appears.

Table 2-25 describes the potential cause(s) of the symptom and the solution(s).

Table 2-25 Holdover Synchronization Alarm 

Possible Problem
Solution

The last reference input has failed.

The clock is running at the frequency of the last known-good reference input. This alarm is raised when the last reference input fails. See the "HLDOVRSYNC" section on page 1-60 for a detailed description of this alarm.


2.5.6 Free-Running Synchronization Mode

Symptom    The clock is running at a different frequency than normal and the FRNGSYNC alarm appears.

Table 2-26 describes the potential cause(s) of the symptom and the solution(s).

Table 2-26 Free-Running Synchronization Mode 

Possible Problem
Solution

No reliable reference input is available.

The clock is using the internal oscillator as its only frequency reference. This occurs when no reliable, prior timing reference is available. See the "FRNGSYNC" section on page 1-58 for a detailed description of this alarm.


2.5.7 Daisy-Chained SETS Not Functioning

Symptom    You are unable to daisy-chain the SETS.

Table 2-27 outlines the problem that might cause this symptom and describes solutions to the problem.

Table 2-27 Daisy-Chained SETS Not Functioning 

Possible Problem
Solution

Daisy-chaining SETS is not supported on the ONS 15454 SDH.

Daisy-chaining SETS causes additional wander buildup in the network and is therefore not supported. Instead, use a timing signal generator to create multiple copies of the SETS clock and separately link them to each ONS 15454 SDH.


2.6 Fiber and Cabling

This section explains problems typically caused by cabling connectivity errors. It also includes instructions for crimping Category 5 cable and lists the optical fiber connectivity levels.

2.6.1 Bit Errors Appear for a Traffic Card

Symptom    A traffic card has multiple Bit errors.

Table 2-28 describes the potential cause(s) of the symptom and the solution(s).

Table 2-28 Bit Errors Appear for a Line Card 

Possible Problem
Solution

Faulty cabling or low optical-line levels.

Bit errors on line (traffic) cards usually originate from cabling problems or low optical-line levels. The errors can be caused by synchronization problems, especially if PJ (pointer justification) errors are reported. Moving cards into different error-free slots will isolate the cause. Use a test set whenever possible because the cause of the errors could be external cabling, fiber, or external equipment connecting to the ONS 15454 SDH. Troubleshoot cabling problems using the "Network Troubleshooting Tests" section. Troubleshoot low optical levels using the "Faulty Fiber-Optic Connections" section.


2.6.2 Faulty Fiber-Optic Connections

Symptom    A line card has multiple SDH alarms and/or signal errors.

Table 2-29 describes the potential cause(s) of the symptom and the solution(s).

Table 2-29 Faulty Fiber-Optic Connections 

Possible Problem
Solution

Faulty fiber-optic connections.

Faulty fiber-optic connections can be the source of SDH alarms and signal errors. Refer to the "Verify Fiber-Optic Connections" section.

Faulty gigabit interface connectors.

Faulty gigabit interface converters can be the source of SDH alarms and signal errors. Refer to the "Replace Faulty Gigabit Interface Converters" section.

Faulty Category 5 cables.

Faulty Category 5 cables can be the source of SDH alarms and signal errors. Refer to the "Crimp Replacement Category 5 Cables" section.



Warning Follow all directions and warning labels when working with optical fibers. To prevent eye damage, never look directly into a fiber or connector. Class IIIb laser. Danger, laser radiation when open. The OC-192 laser is off when the safety key is off (labeled 0). The laser is on when the card is booted and the safety key is in the on position (labeled 1). The port does not have to be in service for the laser to be on. Avoid direct exposure to the beam. Invisible radiation is emitted from the aperture at the end of the fiber optic cable when connected, but not terminated.


Procedure: Verify Fiber-Optic Connections


Step 1 Ensure that a single-mode fiber connects to the ONS 15454 SDH STM-N card.

SM or SM fiber should be printed on the fiber span cable. ONS 15454 SDH STM-N cards do not use multimode fiber.

Step 2 Ensure that the connector keys on the SC fiber connector are properly aligned and locked.

Step 3 Check that the single-mode fiber power level is within the specified range:

a. Remove the receive (Rx) end of the suspect fiber.

b. Connect the receive end of the suspect fiber to a fiber-optic power meter, such as a GN Nettest LP-5000.

c. Determine the power level of fiber with the fiber-optic power meter.

d. Verify the power meter is set to the appropriate wavelength for the optical card being tested (either 1310 nm or 1550 nm depending on the specific card).

e. Verify that the power level falls within the range specified for the card; see the "Optical Card Transmit and Receive Levels" section.

Step 4 If the power level falls below the specified range:

a. Clean or replace the fiber patch cords. If possible, do this for the STM-N card you are working on and the far-end card.

b. Clean the optical connectors on the card. If possible, do this for the STM-N card you are working on and the far-end card.

c. Ensure that the far-end transmitting card is not an ONS intermediate range (IR) card when an ONS long range (LR) card is appropriate.

IR cards transmit a lower output power than LR cards.

d. Replace the far-end transmitting STM-N card to eliminate the possibility of a degrading transmitter on this STM-N card.

e. If the power level still falls below the specified range with the replacement fibers and replacement card, check for one of these three factors that attenuate the power level and affect link loss (LL):

Excessive fiber distance; single-mode fiber attenuates at approximately 0.5 dB/km.

Excessive number or fiber connectors; connectors take approximately 0.5 dB each.

Excessive number of fiber splices; splices take approximately 0.5 dB each.


Note These are typical attenuation values. Refer to the specific product documentation for the actual values or use an optical time domain reflectometer (OTDR) to establish precise link loss and budget requirements.


Step 5 If no power level shows on the fiber, the fiber is bad or the transmitter on the optical card failed.

a. Check that the Transmit (Tx) and Receive (Rx) fibers are not reversed. LOS and EOC alarms normally accompany reversed Tx and Rx fibers. Switching reversed Tx and Rx fibers clears the alarms and restores the signal.

b. Clean or replace the fiber patch cords. If possible, do this for the STM-N card you are working on and the far-end card.

c. Retest the fiber power level.

d. If the replacement fiber still shows no power, replace the optical card.

Step 6 If the power level on the fiber is above the range specified for the card, ensure that an ONS long-range (LR) card is not being used when an ONS intermediate-range (IR) card is appropriate.

LR cards transmit a higher output power than IR cards. When used with short runs of fiber, an LR transmitter will be too powerful for the receiver on the receiving STM-N card.

Receiver overloads occur when maximum receiver power is exceeded.


Tip To prevent overloading the receiver, use an attenuator on the fiber between the ONS STM-N card transmitter and the receiver. Place the attenuator on the receive transmitter of the ONS STM-N cards. Refer to the attenuator documentation for specific instructions.



Tip Most fiber has text printed on only one of the two fiber strands. Use this to identify which fiber is connected to Tx and which fiber is connected to Rx.



Procedure: Replace Faulty Gigabit Interface Converters

Gigabit interface converters (GBICs) are hot-swappable input/output devices that plug into a Gigabit Ethernet port to link the port with the fiber-optic network. Cisco provides three GBIC models: one for short-reach applications, 15454E-GBIC-SX=, one for long-reach applications, 15454E-GBIC-LX=, and one for extra long-reach applications, 15454E-GBIC-ZX=. The short-reach, or "SX" model, connects to multimode fiber and has a maximum cabling distance of 1804 feet. The long-reach, or "LX" model, requires single-mode fiber and has a maximum cabling distance of 10000.5 metres (32,810 feet). The extra long-reach, or "ZX" model, supports extra long-reach applications on the 1550 nm wavelength for up to eighty kilometers. GBICs can be installed or removed while the card and shelf assembly are powered and running. GBIC transmit failure is characterized by a steadily blinking Fail LED on the Gigabit Ethernet (E1000-2/E1000-2-G) card. Figure 2-14 shows a GBIC.

Figure 2-14 A gigabit interface converter (GBIC)


Warning Class 1 laser product



Warning Invisible laser radiation may be emitted from the aperture ports of single-mode fiber optic modules when a cable is not connected. Avoid exposure and do not stare into open apertures.



Step 1 Disconnect the network interface fiber-optic cable from the GBIC SC connector and replace the protective plug.

Step 2 Release the GBIC from the card interface by simultaneously squeezing the two plastic tabs, one on each side of the GBIC.

Step 3 Slide the GBIC out of the Gigabit Ethernet front-panel slot.


Note A flap closes over the GBIC slot to protect the connector on the Gigabit Ethernet (E1000-2/E1000-2-G) card.


Step 4 Remove the new GBIC from its protective packaging.

Step 5 Check the part number to verify that the GBIC is the correct type for your network.


Caution Check the label on the GBIC carefully. The two GBIC models look similar.

Step 6 Grip the sides of the GBIC with your thumb and forefinger and insert the GBIC into the slot on the front panel of the Gigabit Ethernet (E1000-2/E1000-2-G) card (see Figure 2-15).


Note GBICs are keyed to prevent incorrect installation.


Figure 2-15 Installing a GBIC on the E1000-2/E1000-2-G card

Step 7 Slide the GBIC through the front flap until you hear a click.

The click indicates that the GBIC is locked into the slot.

Step 8 When you are ready to attach the network interface fiber-optic cable, remove the protective plug from the GBIC and save the plug for future use.


Procedure: Crimp Replacement Category 5 Cables

You can crimp your own Category 5 cables for use with the ONS 15454 SDH. Use a cross-over cable when connecting an ONS 15454 SDH to a hub, LAN modem, or switch, and use a straight-through cable when connecting an ONS 15454 SDH to a router or workstation. Use Category 5 cable RJ-45 T-568B, Color Code (100 Mbps), and a crimping tool. shows the

Figure 2-16 shows the RJ-45 connector pin numbering. Figure 2-17 shows a straight-through cable wiring layout and Table 2-30 shows the cable pinout. Figure 2-18 shows a cross-over cable wiring layout and Table 2-31 shows the cable pinout.

Figure 2-16 RJ-45 pin numbers

Figure 2-17 A straight-through cable layout

Table 2-30 Straight-through cable pinout 

Pin
Color
Pair
Name
Pin

1

white/orange

2

Transmit Data +

1

2

orange

2

Transmit Data -

2

3

white/green

3

Receive Data +

3

4

blue

1

 

4

5

white/blue

1

 

5

6

green

3

Receive Data -

6

7

white/brown

4

 

7

8

brown

4

 

8


Figure 2-18 A cross-over cable layout

Table 2-31 Cross-over cable pinout 

Pin
Color
Pair
Name
Pin

1

white/orange

2

Transmit Data +

3

2

orange

2

Transmit Data -

6

3

white/green

3

Receive Data +

1

4

blue

1

 

4

5

white/blue

1

 

5

6

green

3

Receive Data -

2

7

white/brown

4

 

7

8

brown

4

 

8



Note Odd-numbered pins always connect to a white wire with a colored stripe.


2.6.3 Optical Card Transmit and Receive Levels

Each STM-N card has a transmit and receive connector on its faceplate. Table 2-32 shows the transmit and receive levels for the optical cards.

Table 2-32 Optical Card Transmit and Receive Levels 

Optical card
Rx
Tx

4/STM1 LH 1310

-8 to -28 dBm

-8 to -15 dBm

STM4 SH 1310

-8 to -28 dBm

-8 to -15 dBm

STM4 LH 1310

-8 to -28 dBm

+2 to -3 dBm

STM4 LH 1550

-8 to -28 dBm

+2 to -3 dBm

STM16 SH 1310

-8 to -28 dBm

+3 to -2 dBm

STM16 LH 1550

-8 to -28 dBm

+3 to -2 dBm

STM16 EH 100GHz

-8 to -28 dBm

0 to -2 dBm

STM64 LH 1550

-9 to -17 dBm

+10 to +7 dBm


2.7 Power and LED Tests

This section provides the "Power Supply Problems" section, the "Power Consumption for Node and Cards" section, and the "Lamp Test for Card LEDs" section.

2.7.1 Power Supply Problems

Symptom    Loss of power or low voltage resulting in a loss of traffic and causing the LCD clock to reset to the default date and time.

Table 2-33 describes the potential cause(s) of the symptom and the solution(s).

Table 2-33 Power Supply Problems

Possible Problem
Solution

Loss of power or low voltage.

The ONS 15454 SDH requires a constant source of DC power to properly function. Input power is -48 VDC. Power requirements range from -42 VDC to -57 VDC.

A newly installed ONS 15454 SDH that is not properly connected to its power supply will not operate. Power problems can be confined to a specific ONS 15454 SDH or affect several pieces of equipment on the site.

A loss of power or low voltage can result in a loss of traffic and causes the LCD clock on the ONS 15454 SDH to default to January 1, 1970, 00:04:15. For clock reset instructions, refer to the Cisco ONS 15454 SDH Installation and Operations Guide.

Refer to the "Isolate the Cause of Power Supply Problems" section.

Improperly connected power supply.



Caution Operations that interrupt power supply or short the power connections to the ONS 15454 SDH are service-affecting.


Warning When working with live power, always use proper tools and eye protection.



Warning Always use the supplied electrostatic discharge (ESD) wristband when working with a powered ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower-right outside edge of the shelf assembly.


Procedure: Isolate the Cause of Power Supply Problems


Step 1 If a single ONS 15454 SDH show signs of fluctuating power or power loss:

a. Verify that the -48 VDC #8 power terminals are properly connected to a fuse panel. These power terminals are located on the lower section of the backplane FMEC card under the clear plastic cover.

b. Verify that the power cable is #12 or #14 AWG and in good condition.

c. Verify that the power cable connections are properly crimped. Stranded #12 or #14 AWG does not always crimp properly with Staycon type connectors.

d. Verify that 20A fuses are used in the fuse panel.

e. Verify that the fuses are not blown.

f. Verify that a rack-ground cable attaches to the frame-ground terminal (FGND) on the right side of the ONS 15454 SDH FMEC card. Connect this cable to the ground terminal according to local site practice.

g. Verify that the DC power source has enough capacity to carry the power load.

h. If the DC power source is battery-based:

Check that the output power is high enough. Power requirements range from -42 VDC to -57
VDC.

Check the age of the batteries. Battery performance decreases with age.

Check for opens and shorts in batteries, which may affect power output.

If brownouts occur, the power load and fuses may be too high for the battery plant.

Step 2 If multiple pieces of site equipment show signs of fluctuating power or power loss:

a. Check the uninterruptible power supply (UPS) or rectifiers that supply the equipment. Refer to the UPS manufacturer's documentation for specific instructions.

b. Check for excessive power drains caused by other equipment, such as generators.

c. Check for excessive power demand on backup power systems or batteries when alternate power sources are used.


2.7.2 Power Consumption for Node and Cards

Symptom    You are unable to power up a node or the cards in a node.

Table 2-34 describes the potential cause(s) of the symptom and the solution(s).

Table 2-34 Power Consumption for Node and Cards 

Possible Problem
Solution

Improper power supply.

Refer to power information in the Cisco ONS 15454 SDH Installation and Operations Guide.


2.7.3 Lamp Test for Card LEDs

Symptom    Card LED will not light or you are unsure if LEDs are working properly.

Table 2-35 describes the potential cause(s) of the symptom and the solution(s).

Table 2-35 Lamp Test for Card LEDs 

Possible Problem
Solution

Faulty LED

A lamp test verifies that all the card LEDs work. Run this diagnostic test as part of the initial ONS 15454 SDH turn-up, a periodic maintenance routine, or any time you question whether an LED is in working order.

See the "Verify Card LED Operation" section.


Procedure: Verify Card LED Operation


Step 1 Click the Maintenance > Diagnostic tabs.

Step 2 Click Lamp Test.

Step 3 Watch to make sure all the LEDs on the cards illuminate for several seconds.

Step 4 Click OK on the Lamp Test Run dialog box.

If an LED does not illuminate, the LED is faulty. Return the defective card to Cisco through the returned materials authorization (RMA) process. Contact the Cisco Technical Assistance Center (Cisco TAC) at 1-877-323-7368 or obtain a directory of toll-free Cisco TAC telephone numbers at the following URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.