リカバリ アップグレード手順を実行できるのは、SPA の初期化の試行がすべて失敗したあと、システムによって電源がオフにされている SPA に限られます。
次の例は、サブスロット 0/1 に搭載された SPA について、初期化するためのすべての試行を行う前に、リカバリ アップグレードを実行しようとした場合の出力を示しています。
(注) |
リカバリ アップグレードはより慎重に行われるため、予想したアップグレード時間よりも多くの時間がかかる場合があります。
|
(注) |
システムから「Do you want to perform the recovery upgrade operation?」と質問されるいくつかの場合があります。この質問が表示された場合、電源障害や SPA の取り外しの結果、FPD のアップグレードに失敗した時にだけ
y を選択してください。それ以外の理由でアップグレードに失敗し、この質問が表示された場合には、シスコのテクニカル サポートまでご連絡ください。
|
Nov.28 11:29:55:%SPA_OIR-3-RECOVERY_RELOAD:subslot 0/1:Attempting
recovery by reloading SPA
Nov.28 11:30:10:%SPA_OIR-3-HW_INIT_TIMEOUT:subslot 0/1
Nov.28 11:30:15:%SPA_OIR-3-RECOVERY_RELOAD:subslot 0/1:Attempting
recovery by reloading SPA
Nov.28 11:30:31:%SPA_OIR-3-HW_INIT_TIMEOUT:subslot 0/1
Router# upgrade hw-module subslot 0/1 fpg bundled
% Cannot get FPD version information for version checking. If a previous
upgrade attempt has failed for the target card, then a recovery upgrade
would be required to fix the failure.
% The following FPD(s) will be upgraded for SPA-4XOC3-POS (H/W ver =
1.0) in subslot 0/1:
================== =========== =========== ============
Field Programmable Current Upgrade Estimated
Device:"ID-Name" Version Version Upgrade Time
================== =========== =========== ============
1-I/O FPGA ?.? 3.4 00:00:50
================== =========== =========== ============
% Do you want to perform the recovery upgrade operation? [no]:y
% Cannot perform recovery upgrade operation because the target card is
not in a failed state. Please try again later.
次のエラー メッセージが表示された場合は、リカバリ アップグレードを実行できます。
Nov.28 11:31:31:%SPA_OIR-3-SPA_POWERED_OFF:subslot 0/1:SPA 4xOC3 POS SPA powered off after 5 failures within 600 seconds
(注) |
アップグレードを試行する前に、このエラー メッセージが表示されるまで待つ必要があります。
|
upgrade hw-module subslot コマンドを使用して、手動で FPD イメージ アップグレードを実行し、システムによって SPA の電源がオフになったら、壊れたイメージからの回復を行います。このコマンドでは、slot-number が SIP のインストールされているスロット、subslot-number が SPA のある SIP のサブスロットを意味します。
次に、リカバリ アップグレード処理のコンソールの出力例を示します。
Router# upgrade hw-module subslot 0/1 fpd bundled
% Cannot get FPD version information from SPA-4XOC3-POS in subslot 0/1.
If a previous upgrade attempt on the target card was interrupted, then the
corruption of FPD image might have prevented the card from coming online.
If this is the case, then a recovery upgrade would be required to fix the
failure.
(Hit ENTER to proceed with recovery upgrade operation) [confirm]
% The following FPD will be upgraded for SPA-4XOC3-POS (H/W ver = 1.0) in subslot 0/1:
================== =========== =========== ============
Field Programmable Current Upgrade Estimated
Device: "ID-Name" Version Version Upgrade Time
================== =========== =========== ============
1-I/O FPGA ?.? 3.4 00:00:50
================== =========== =========== ============
% NOTES:
- Use 'show upgrade fpd progress' command to view the progress of the FPD
upgrade.
- Since the target card is currently in disabled state, it will be
automatically reloaded after the upgrade operation for the changes to
take effect.
% Do you want to perform the recovery upgrade operation? [no]: y
% Starting recovery upgrade operation in the background ...
(Use "show upgrade fpd progress" command to see upgrade progress)
Router#
*Nov 28 17:46:10.191:%FPD_MGMT-6-UPGRADE_TIME: Estimated total FPD image upgrade time for SPA-4XOC3-POS card in subslot 0/1 = 00:00:50.
*Nov 28 17:46:10.233:%FPD_MGMT-6-UPGRADE_START: I/O FPGA (FPD ID=1) image upgrade in progress for SPA-4XOC3-POS card in subslot 0/1. Updating to version 3.4. PLEASE DO NOT INTERRUPT DURING THE UPGRADE PROCESS (estimated upgrade completion time = 00:00:50) ...
*Nov 28 17:46:55.948:%FPD_MGMT-6-UPGRADE_PASSED: I/O FPGA (FPD ID=1) image in the SPA-4XOC3-POS card in subslot 0/1 has been successfully updated from version ?.? to version 3.4. Upgrading time = 00:00:45.715
*Nov 28 17:46:55.948:%FPD_MGMT-6-OVERALL_UPGRADE: All the attempts to upgrade the required FPD images have been completed for SPA-4XOC3-POS card in subslot 0/1. Number of successful/failure upgrade(s): 1/0.
*Nov 28 17:46:55.949:%FPD_MGMT-5-CARD_POWER_CYCLE: SPA-4XOC3-POS card in subslot 0/1 is being power cycled for the FPD image upgrade to take effect.