Application Visibility and Control

Information About Application Visibility and Control

Application Visibility and Control (AVC) is a subset of the entire Flexible NetFlow (FNF) package that can provide traffic information. The AVC feature employs a distributed approach that benefits from NBAR running on the access point (AP) or embedded wireless controller whose goal is to run deep packet inspection (DPI) and reports the results using FNF messages.

AVC enables you to perform real-time analysis and create policies to reduce network congestion, costly network link usage, and infrastructure upgrades. Traffic flows are analyzed and recognized using the NBAR2 engine. The specific flow is marked with the recognized protocol or application. This per-flow information can be used for application visibility using FNF. After the application visibility is established, a user can define control rules with policing mechanisms for a client.

Using AVC rules, you can limit the bandwidth of a particular application for all the clients joined on the WLAN. These bandwidth contracts coexist with per-client downstream rate limiting that takes precedence over the per-application rate limits.

FNF feature is supported in wireless, and relies on the NetFlow enablement on the embedded wireless controller for flex mode.

The behavior of the AVC solution changes based on the wireless deployments. The following sections describe the commonalities and differences in all scenarios:

Flex Mode

  • NBAR is enabled on an AP

  • AVC pushes the FNF configuration to the APs.

  • Supports context transfer for roaming in AVC-FNF.

  • Supports NetFlow exporter.

Prerequisites for Application Visibility and Control

  • The access points should be AVC capable.

  • For the control part of AVC (QoS) to work, the application visibility feature with FNF has to be configured.

Restrictions for Application Visibility and Control

  • Layer 2 roaming is not supported across embedded wireless controllercontrollers.

  • Multicast traffic is not supported.

  • AVC is supported only on the following access points:

    • Cisco Aironet 1800 Series Access Points

    • Cisco Aironet 2700 Series Access Point

    • Cisco Aironet 2800 Series Access Point

    • Cisco Aironet 3700 Series Access Points

    • Cisco Aironet 3800 Series Access Points

    • Cisco Aironet 4800 Series Access Points

  • AVC is not supported on Cisco Aironet 702W, 702I (128 M memory), and 1530 Series access points.

  • Only the applications that are recognized with App visibility can be used for applying QoS control.

  • Data link is not supported for NetFlow fields in AVC.

  • You cannot map the same WLAN profile to both the AVC-not-enabled policy profile and the AVC-enabled policy profile.

  • NBAR-based QoS policy configuration is allowed at client level and BSSID level, configured on policy profile.

  • NBAR is not able to classify traffic accurately when SaaS applications use end-to-end encryption, QUIC, or DoH due to the encryption's impact on classification. In such a case, the encrypted traffic, including DoH and QUIC without SNI, limits the NBAR's ability to send the correct Protocol ID, causing issues with traffic classification.

When AVC is enabled, the AVC profile supports only up to 23 rules, which includes the default DSCP rule. The AVC policy will not be pushed down to the AP, if rules are more than 23.

AVC Configuration Overview

To configure AVC, follow these steps:

  1. Create a flow monitor using the record wireless avc basic command.

  2. Create a wireless policy profile.

  3. Apply the flow monitor to the wireless policy profile.

  4. Create a wireless policy tag.

  5. Map the WLAN to the policy profile

  6. Attach the policy tag to the APs.

Create a Flow Monitor

The NetFlow configuration requires a flow record, a flow monitor, and a flow exporter. This configuration should be the first step in the overall AVC configuration.


Note

In Flex mode, the default values for cache timeout active and cache timeout inactive commands are not optimal for AVC. We recommend that you set both the values to 60 in the flow monitor.

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

flow monitor monitor-name

Example:

Device(config)# flow monitor fm_avc

Creates a flow monitor.

Step 3

record wireless avc basic

Example:

Device(config-flow-monitor)# record wireless 
avc basic

Specifies the basic wireless AVC flow template.

Note

 

The record wireless avc basic command is same as record wireless avc ipv4 basic command. However, record wireless avc ipv4 basic command is not supported in Flex or Fabric modes. In such scenarios, use the record wireless avc basic command.

Configuring a Flow Monitor (GUI)

Before you begin

You must have created a flow exporter to export data from the flow monitor.

Procedure

Step 1

Choose Configuration > Services > Application Visibility and go to the Flow Monitor tab .

Step 2

In the Monitor area, click Add to add a flow monitor.

Step 3

In the Flow Monitor window, add a flow monitor and a description.

Step 4

Select the Flow exporter from the drop-down list to export the data from the flow monitor to a collector.

Note

 

To export wireless netflow data, use the templates below:

  • ETA (Encrypted Traffic Analysis)

  • wireless avc basic

  • wireless avc basic IPv6

Step 5

Click Apply to Device to save the configuration.

Create a Flow Exporter

You can create a flow exporter to define the export parameters for a flow. This is an optional procedure for configuring flow exporter parameters.


Note

For the AVC statistics to be visible at the embedded wireless controller, you should configure a local flow exporter using the following commands:

  • flow exporter my_local

  • destination local wlc

Also, your flow monitor must use this local exporter for the statistics to be visible at the embedded wireless controller.

Procedure

  Command or Action Purpose

Step 1

flow exporter flow-export-name

Example:

Device(config)# flow exporter export-test

Creates a flow monitor.

Step 2

description string

Example:

Device(config-flow-exporter)# description IPv4flow

Describes the flow record as a maximum 63-character string.

Step 3

Example:

Device(config-flow-exporter)# destination local wlc

Specifies the local WLC to which the exporter sends data.

Step 4

end

Example:

Device(config-flow-exporter)# end

Returns to privileged EXEC mode.

Step 5

show flow exporter

Example:

Device# show flow exporter

(Optional) Verifies your configuration.

Verify the Flow Exporter

To verify the flow exporter description, use the following command:

For example, to verify the flow exporter description for the flow exporter named my-flow-exporter, see the example below: 

Device# show flow exporter
Flow Exporter my-flow-exporter:
  Description:              User defined
  Export protocol:          NetFlow Version 9
  Transport Configuration:
    Destination type:       Local (1)
    Destination IP address: 0.0.0.0
    Source IP address:      10.0.0.1
    Transport Protocol:     UDP
    Destination Port:       9XXX
    Source Port:            5XXXX
    DSCP:                   0x0
    TTL:                    255
    Output Features:        Not Used

Note
A flow exporter with no destination is marked as an UNKNOWN type. The following are the two ways the exporter is marked as UNKNOWN:

  1. When you configure the flow exporter using the CLI commands without a destination.

  2. EWC supports a maximum of one external and one internal flow exporter. If you attempt to configure more than one flow exporter per type, this results in the destination to be rejected and the flow exporter will be considered as UNKNOWN.

Configuring a Policy Tag

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

wireless tag policy policy-tag-name

Example:

Device(config-policy-tag)# wireless tag policy rr-xyz-policy-tag

Configures policy tag and enters policy tag configuration mode.

Step 3

end

Example:

Device(config-policy-tag)# end

Saves the configuration and exits configuration mode and returns to privileged EXEC mode.

Attaching a Policy Profile to a WLAN Interface (GUI)

Procedure

Step 1

Choose Configuration > Tags & Profiles > Tags.

Step 2

On the Manage Tags page, click Policy tab.

Step 3

Click Add to view the Add Policy Tag window.

Step 4

Enter a name and description for the policy tag.

Step 5

Click Add to map WLAN and policy.

Step 6

Choose the WLAN profile to map with the appropriate policy profile, and click the tick icon.

Step 7

Click Save & Apply to Device.

Attaching a Policy Profile to a WLAN Interface (CLI)

Before you begin

  • Do not attach different AVC policy profiles on the same WLAN across different policy tags.

    The following is an example of incorrect configuration:

    wireless profile policy avc_pol1
   ipv4 flow monitor fm-avc1 input
   ipv4 flow monitor fm-avc1 output
   no shutdown
  wireless profile policy avc_pol2
   ipv4 flow monitor fm-avc2 input
   ipv4 flow monitor fm-avc2 output
   no shutdown
  wireless tag policy avc-tag1
   wlan wlan1 policy avc_pol1
  wireless tag policy avc-tag2
   wlan wlan1 policy avc_pol2

    This example violates the restriction stated earlier, that is, the WLAN wlan1 is mapped to 2 policy profiles, avc_pol1 and avc_pol2. This configuration is, therefore, incorrect because the WLAN wlan1 should be mapped to either avc_pol1 or avc_pol2 everywhere.

  • Conflicting policy profiles on the same WLAN are not supported. For example, policy profile (with and without AVC) applied to the same WLAN in different policy tags.

    The following is an example of an incorrect configuration:

    wireless profile policy avc_pol1
   no shutdown
  wireless profile policy avc_pol2
   ipv4 flow monitor fm-avc2 input
   ipv4 flow monitor fm-avc2 output
   no shutdown
  wireless tag policy avc-tag1
   wlan wlan1 policy avc_pol1
  wireless tag policy avc-tag2
   wlan wlan1 policy avc_pol2

    In this example, a policy profile with and without AVC is applied to the same WLAN in different tags.

Procedure

  Command or Action Purpose

Step 1

wireless tag policy avc-tag

Example:

Device(config)# wireless tag policy avc-tag

Creates a policy tag.

Step 2

wlan wlan-avc policy avc-policy

Example:

Device(config-policy-tag)# wlan wlan_avc policy avc_pol

Attaches a policy profile to a WLAN profile.

What to do next

  • Run the no shutdown command on the WLAN after completing the configuration.

  • If the WLAN is already in no shutdown mode, run the shutdown command, followed by no shutdown command.

Attaching a Policy Profile to an AP

Procedure

  Command or Action Purpose

Step 1

ap ap-ether-mac

Example:

Device(config)# ap 34a8.2ec7.4cf0

Enters AP configuration mode.

Step 2

policy-tag policy-tag

Example:

Device(config)# policy-tag avc-tag

Specifies the policy tag that is to be attached to the access point.

Verify the AVC Configuration

Procedure

  Command or Action Purpose

Step 1

show avc wlan wlan-name top num-of-applications applications {aggregate | downstream | upstream}

Example:

Device# show avc wlan wlan_avc top 2 applications aggregate

Displays information about top applications and users using these applications.

Note

 

Ensure that wireless clients are associated to the WLAN and generating traffic, and then wait for 90 seconds (to ensure the availability of statistics) before running the command.

Step 2

show avc client mac top num-of-applications applications {aggregate | downstream | upstream}

Example:

Device# show avc client 9.3.4 top 3 applications aggregate

Displays information about the top number of applications.

Note

 

Ensure that wireless clients are associated to the WLAN and generating traffic, and then wait for 90 seconds (to ensure the availability of statistics) before running the command.

Step 3

show avc wlan wlan-name application app-name top num-of-clients aggregate

Example:

Device# show avc wlan wlan_avc application app top 4 aggregate

Displays information about top applications and users using these applications.

Step 4

show ap summary

Example:

Device# show ap summary

Displays a summary of all the access points attached to the embedded wireless controller.

Step 5

show ap tag summary

Example:

Device# show ap tag summary

Displays a summary of all the access points with policy tags.

AVC-Based Selective Reanchoring

The AVC-Based Selective Reanchoring feature is designed to reanchor clients when they roam from one embedded wireless controller to another. Reanchoring of clients prevents the depletion of IP addresses available for new clients in Cisco WLC. The AVC profile-based statistics are used to decide whether a client must be reanchored or deferred. This is useful when a client is actively running a voice or video application defined in the AVC rules.

The reanchoring process also involves deauthentication of anchored clients. The clients get deauthenticated when they do not transmit traffic for the applications listed in the AVC rules while roaming between WLCs.

Restrictions for AVC-Based Selective Reanchoring

  • This feature is supported only in local mode. FlexConnect and fabric modes are not supported.

  • This feature is not supported in guest tunneling and export anchor scenarios.

  • The old IP address is not released after reanchoring, until IP address' lease period ends.

Configuring the Flow Exporter

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

flow exporter name

Example:

Device(config)# flow exporter avc-reanchor

Creates a flow exporter and enters flow exporter configuration mode.

Note

 

You can use this command to modify an existing flow exporter too.

Step 3

destination local wlc

Example:

Device(config-flow-exporter)# destination local wlc

Sets the exporter as local.

Configuring the Flow Monitor

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

flow monitor monitor-name

Example:

Device(config)# flow monitor fm_avc

Creates a flow monitor and enters Flexible NetFlow flow monitor configuration mode.

Note

 

You can use this command to modify an existing flow monitor too.

Step 3

exporter exporter-name

Example:

Device(config-flow-monitor)# exporter avc-reanchor

Specifies the name of an exporter.

Step 4

record wireless avc basic

Example:

Device(config-flow-monitor)# record wireless avc basic

Specifies the flow record to use to define the cache.

Step 5

cache timeout active value

Example:

Device(config-flow-monitor)# cache timeout active 60

Sets the active flow timeout, in seconds.

Step 6

cache timeout inactive value

Example:

Device(config-flow-monitor)# cache timeout inactive 60

Sets the inactive flow timeout, in seconds.

Configuring the AVC Reanchoring Profile

Before you begin

  • Ensure that you use the AVC-Reanchor-Class class map. All other class-map names are ignored by Selective Reanchoring.

  • During boot up, the system checks for the existence of the AVC-Reanchor-Class class map. If it is not found, default protocols, for example, jabber-video, WiFi-calling, and so on, are created. If AVC-Reanchor-Class class map is found, configuration changes are not made and updates to the protocols that are saved to the startup configuration persist across reboots.

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

class-map cmap-name

Example:

Device(config)# class-map AVC-Reanchor-Class

Configures the class map.

Step 3

match any

Example:

Device(config-cmap)# match any

Instructs the device to match with any of the protocols that pass through it.

Step 4

match protocol jabber-audio

Example:

Device(config-cmap)# match protocol jabber-audio

Specifies a match to the application name.

You can edit the class-map configuration later, in order to add or remove protocols, for example, jabber-video, wifi-calling, and so on, if required.

Configuring the Wireless WLAN Profile Policy

Follow the procedure given below to configure the WLAN profile policy:

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

wireless profile policy policy-name

Example:

Device(config)# wireless profile policy default-policy-profile

Configures the WLAN policy profile and enters wireless policy configuration mode.

Step 3

shutdown

Example:

Device(config-wireless-policy)# shutdown

Disables the policy profile.

Step 4

central switching

Example:

Device(config-wireless-policy)# central switching

Enables central switching.

Step 5

ipv4 flow monitor monitor-name input

Example:

Device(config-wireless-policy)# ipv4 flow monitor fm_avc input

Specifies the name of the IPv4 ingress flow monitor.

Step 6

ipv4 flow monitor monitor-name output

Example:

Device(config-wireless-policy)# ipv4 flow monitor fm_avc output

Specifies the name of the IPv4 egress flow monitor.

Step 7

reanchor class class-name

Example:

Device(config-wireless-policy)# reanchor class AVC-Reanchor-Class

Configure a class map with protocols for the Selective Reanchoring feature.

Step 8

no shutdown

Example:

Device(config-wireless-policy)# no shutdown

Enables the policy profile.

Verifying AVC Reanchoring

Use the following commands to verify the AVC reanchoring configuration:

Device# show wireless profile policy detailed avc_reanchor_policy

Policy Profile Name           : avc_reanchor_policy
Description                   : 
Status                        : ENABLED
VLAN                          : 1
Wireless management interface VLAN        : 34
!
.
.
.
AVC VISIBILITY                : Enabled
Flow Monitor IPv4
  Flow Monitor Ingress Name   : fm_avc
  Flow Monitor Egress Name    : fm_avc
Flow Monitor IPv6
  Flow Monitor Ingress Name   : Not Configured
  Flow Monitor Egress Name    : Not Configured
NBAR Protocol Discovery       : Disabled
Reanchoring                   : Enabled
Classmap name for Reanchoring
  Reanchoring Classmap Name   : AVC-Reanchor-Class
!
.
.
.
  -------------------------------------------------------


Device# show platform software trace counter tag wstatsd chassis active R0 avc-stats debug

Counter Name Thread ID Counter Value 
------------------------------------------------------------------------------
Reanch_deassociated_clients 28340 1 
Reanch_tracked_clients 28340 4 
Reanch_deleted_clients 28340 3 

Device# show platform software trace counter tag wncd chassis active R0 avc-afc debug

Counter Name Thread ID Counter Value 
------------------------------------------------------------------------------
Reanch_co_ignored_clients 30063 1 
Reanch_co_anchored_clients 30063 5 
Reanch_co_deauthed_clients 30063 4


Device# show platform software wlavc status wncd

Event history of WNCD DB:

AVC key: [1,wlan_avc,N/A,Reanc,default-policy-tag]
Current state : READY
Wlan-id : 1
Wlan-name : wlan_avc
Feature type : Reanchoring
Flow-mon-name : N/A
Policy-tag : default-policy-tag
Switching Mode : CENTRAL

Timestamp FSM State Event RC Ctx
-------------------------- ------------------- -------------------------- ---- ----
06/12/2018 16:45:30.630342 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:45:28.822780 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:28.822672 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:15.172073 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:45:12.738367 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:12.738261 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:01.162689 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:44:55.757643 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:55.757542 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:04.468749 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:44:02.18857 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:02.18717 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:38:20.164304 2 :READY 3 :FSM_AFM_SWEEP 0 2
06/12/2018 16:35:20.163877 2 :READY 1 :FSM_AFM_BIND 0 2
06/12/2018 16:35:18.593257 1 :INIT 1 :FSM_AFM_BIND 0 2
06/12/2018 16:35:18.593152 1 :INIT 24:CREATE_FSM 0 0

AVC key: [1,wlan_avc,fm_avc,v4-In,default-policy-tag]
Current state : READY
Wlan-id : 1
Wlan-name : wlan_avc
Feature type : Flow monitor IPv4 Ingress
Flow-mon-name : fm_avc
Policy-tag : default-policy-tag
Switching Mode : CENTRAL

Timestamp FSM State Event RC Ctx
-------------------------- ------------------- -------------------------- ---- ----
06/12/2018 16:45:30.664772 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:45:28.822499 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:28.822222 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:15.207605 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:45:12.738105 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:12.737997 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:01.164225 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:44:55.757266 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:55.757181 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:04.472778 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:44:02.15413 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:02.15263 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:38:20.164254 2 :READY 3 :FSM_AFM_SWEEP 0 2
06/12/2018 16:35:20.163209 1 :INIT 1 :FSM_AFM_BIND 0 2
06/12/2018 16:35:20.163189 1 :INIT 24:CREATE_FSM 0 0

AVC key: [1,wlan_avc,fm_avc,v4-Ou,default-policy-tag]
Current state : READY
Wlan-id : 1
Wlan-name : wlan_avc
Feature type : Flow monitor IPv4 Egress
Flow-mon-name : fm_avc
Policy-tag : default-policy-tag
Switching Mode : CENTRAL

Timestamp FSM State Event RC Ctx
-------------------------- ------------------- -------------------------- ---- ----
06/12/2018 16:45:30.630764 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:45:28.822621 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:28.822574 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:15.172357 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:45:12.738212 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:12.738167 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:45:01.164048 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:44:55.757403 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:55.757361 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:04.472561 3 :ZOMBIE 1 :FSM_AFM_BIND 0 2
06/12/2018 16:44:02.18660 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:44:02.18588 2 :READY 2 :FSM_AFM_UNBIND 0 0
06/12/2018 16:38:20.164293 2 :READY 3 :FSM_AFM_SWEEP 0 2
06/12/2018 16:35:20.163799 1 :INIT 1 :FSM_AFM_BIND 0 2
06/12/2018 16:35:20.163773 1 :INIT 24:CREATE_FSM 0 0


Device# show platform software wlavc status wncmgrd

Event history of WNCMgr DB:

AVC key: [1,wlan_avc,N/A,Reanc,default-policy-tag]
Current state : READY
Wlan-id : 1
Wlan-name : wlan_avc
Feature type : Reanchoring
Flow-mon-name : N/A
Policy-tag : default-policy-tag
Switching Mode : CENTRAL
Policy-profile : AVC_POL_PYATS

Timestamp FSM State Event RC Ctx
-------------------------- ------------------- -------------------------- ---- ----
06/12/2018 16:45:30.629278 3 :WLAN_READY 24:BIND_WNCD 0 0
06/12/2018 16:45:30.629223 3 :WLAN_READY 4 :FSM_BIND_ACK 0 0
06/12/2018 16:45:30.629179 3 :WLAN_READY 4 :FSM_BIND_ACK 0 0
06/12/2018 16:45:30.510867 2 :PLUMB_READY 22:BIND_IOSD 0 0
06/12/2018 16:45:30.510411 2 :PLUMB_READY 2 :FSM_WLAN_UP 0 0
06/12/2018 16:45:30.510371 2 :PLUMB_READY 1 :FSM_WLAN_FM_PLUMB 0 0
06/12/2018 16:45:28.886377 2 :PLUMB_READY 20:UNBIND_ACK_IOSD 0 0
!

AVC key: [1,wlan_avc,fm_avc,v4-In,default-policy-tag]
Current state : READY
Wlan-id : 1
Wlan-name : wlan_avc
Feature type : Flow monitor IPv4 Ingress
Flow-mon-name : fm_avc
Policy-tag : default-policy-tag
Switching Mode : CENTRAL
Policy-profile : AVC_POL_PYATS

Timestamp FSM State Event RC Ctx
-------------------------- ------------------- -------------------------- ---- ----
06/12/2018 16:45:30.664032 3 :WLAN_READY 24:BIND_WNCD 0 0
06/12/2018 16:45:30.663958 3 :WLAN_READY 4 :FSM_BIND_ACK 0 0
06/12/2018 16:45:30.663921 3 :WLAN_READY 4 :FSM_BIND_ACK 0 0
06/12/2018 16:45:30.511151 2 :PLUMB_READY 22:BIND_IOSD 0 0
06/12/2018 16:45:30.510624 2 :PLUMB_READY 2 :FSM_WLAN_UP 0 0
06/12/2018 16:45:30.510608 2 :PLUMB_READY 1 :FSM_WLAN_FM_PLUMB 0 0
06/12/2018 16:45:28.810867 2 :PLUMB_READY 20:UNBIND_ACK_IOSD 0 0
06/12/2018 16:45:28.807239 4 :READY 25:UNBIND_WNCD 0 0
06/12/2018 16:45:28.807205 4 :READY 23:UNBIND_IOSD 0 0
06/12/2018 16:45:28.806734 4 :READY 3 :FSM_WLAN_DOWN 0 0
!

AVC key: [1,wlan_avc,fm_avc,v4-Ou,default-policy-tag]
Current state : READY
Wlan-id : 1
Wlan-name : wlan_avc
Feature type : Flow monitor IPv4 Egress
Flow-mon-name : fm_avc
Policy-tag : default-policy-tag
Switching Mode : CENTRAL
Policy-profile : AVC_POL_PYATS

Timestamp FSM State Event RC Ctx
-------------------------- ------------------- -------------------------- ---- ----
06/12/2018 16:45:30.629414 3 :WLAN_READY 24:BIND_WNCD 0 0
06/12/2018 16:45:30.629392 3 :WLAN_READY 4 :FSM_BIND_ACK 0 0
06/12/2018 16:45:30.629380 3 :WLAN_READY 4 :FSM_BIND_ACK 0 0
06/12/2018 16:45:30.510954 2 :PLUMB_READY 22:BIND_IOSD 0 0
06/12/2018 16:45:30.510572 2 :PLUMB_READY 2 :FSM_WLAN_UP 0 0
06/12/2018 16:45:30.510532 2 :PLUMB_READY 1 :FSM_WLAN_FM_PLUMB 0 0
06/12/2018 16:45:28.886293 2 :PLUMB_READY 20:UNBIND_ACK_IOSD 0 0
06/12/2018 16:45:28.807844 4 :READY 25:UNBIND_WNCD 0 0
06/12/2018 16:45:28.807795 4 :READY 23:UNBIND_IOSD 0 0
06/12/2018 16:45:28.806990 4 :READY 3 :FSM_WLAN_DOWN 0 0
!