Cisco Wireless LAN Controller System Message Guide, Release 7.3

NIM Messages
NMSP Messages
NULL Messages
OSAPI Messages

NIM NMSP NULL and OSAPI System Messages

This chapter contains the following topics:

NIM Messages

This section contains Networks-in-Motion (NIM) messages.

Error Message    NIM-0-ADMIN_MODE_DISABLE: Port %d Admin Mode is Disable.

Explanation The Port Admin Mode is disabled.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/cisco/web/support/index.html. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    NIM-0-ADMIN_MODE_ENABLE: Port %d Admin Mode is Enable.

Explanation The Port Admin Mode is enabled.

Error Message    %NIM-0-CREAT_TASK_FAIL: Failed to create the task [chars]

Explanation The system has failed to create the task.

Error Message    NIM-0-GET_LAGMAC_FAIL: LAG MAC address error: Invalid arguments. Got 
null pointer.

Explanation A LAG MAC address error has occurred: The system has detected invalid arguments. The system has a null pointer.

Error Message    NIM-0-INDEX_ERR: Invalid index [int] while %s per port AP load 
information.

Explanation An internal error has occurred when processing AP load information. Some AP management functions may not work as expected.

Error Message    %NIM-0-MSGQ_CREATE_FAIL: Unable to create msg queue for nimTask.

Explanation The system is unable to create a message queue for nimTask.

Error Message    %NIM-0-REGISTRY_GET_FAIL: Unable to pull value from the registry for 
the key [chars]

Explanation The system is unable to pull a value from the registry.

Error Message    %NIM-3-ADMIN_STATE_INVALID: Admin State [dec] is not valid for 
interface [dec].

Explanation The admin state is not valid. The state is not enabled or disabled.

Error Message    %NIM-3-CANT_DISABLE_MCAST: Cannot disable multicast state for 
interface [int] when LAG is enabled

Explanation The system cannot disable multicast state when LAG is enabled.

Error Message    %NIM-3-CHECK_SUM_ERR: Checksum Error on config file [chars].

Explanation A checksum error has occurred on the configuration file.

Recommended Action No action is required.

Error Message    %NIM-3-COMPONENT_ALREADY_REGISTERED: Component [dec] already 
registered.

Explanation The component is already registered. A component that is already registered with a state change function is trying to register again.

Error Message    %NIM-3-CREAT_CPUINTF_FAIL: CPU INTF Create error: Ran out of CPU 
Interface internal numbers.

Explanation NIM Create error: The system has run out of CPU interface internal numbers.

Error Message    %NIM-3-CREAT_LAGINTF_FAIL: LAG interface Create error:Ran out of LAG 
Interface internal numbers.

Explanation LAG interface Create error: The system has run out of LAG interface internal numbers.

Error Message    %NIM-3-CREAT_LOGICALINTF_FAIL: Logical interface create error:Ran out 
of Logical Interface internal numbers.

Explanation Logical interface create error: The system has run out of logical interface internal numbers.

Error Message    %NIM-3-CREAT_PHYINTF_FAIL: PHY interface Create error: Ran out of 
Physical Interface internal numbers.

Explanation PHY interface Create error: The system has run out of physical interface internal numbers.

Error Message    %NIM-3-CREAT_VLANINTF_FAIL: Logical Vlan interface Create error:Ran 
out of Logical Interface internal numbers.

Explanation Logical VLAN interface Create error: The system has run out of logical interface internal numbers.

Error Message    %NIM-3-FS_WRITE_FAIL: Writing data to the config file [chars] failed.

Explanation Writing data to the user configuration file has failed.

Error Message    %NIM-3-INIT_TASK_FAIL: Task initialization failure. Waiting on handle 
[chars] failed

Explanation Task initializing has failed for a NIM component.

Error Message    %NIM-3-INVALID_CREAT_REQUEST: Invalid [chars] Create Request.

Explanation An invalid interface create request has occurred.

Error Message    %NIM-3-LOAD_PORTINFO_FAIL: Loading port info for port number [dec] 
failed. Ran out of Physical Interface internal numbers.

Explanation Loading the multicast appliance mode port configuration has failed. The system has run out of physical interface internal numbers.

Error Message    %NIM-3-MCAST_STATE_UNKNOWN: interface [int] has invalid 
mcastApplianceState [dec]

Explanation The multicast appliance state is invalid.

Error Message    %NIM-3-SET_AUTONEG_FAIL: Error in setting the AutoNeg status for the 
interface with internal interface number [dec].

Explanation An error occurred while setting the status for auto negotiation.

Error Message    %NIM-3-SET_INTFSPEED_FAIL: Error while setting the speed mode for the 
interface with internal interface number [dec].

Explanation An error occurred while setting the speed mode for the interface. The speed and the interface type are not compatible.

Error Message    %NIM-3-SET_MCASTSTATE_FAIL: Error while setting MCAST appliance state 
for the interface with internal interface number [dec].

Explanation An error occurred while setting the MCAST appliance state for an interface.

Error Message    %NIM-3-SET_MTUSIZE_FAIL: Error while setting MTU size for the 
interface with the internal interface number [dec].

Explanation An error occurred while setting the MTU size for the interface.

Error Message    %NIM-3-SYSINTF_TYPE_UNKNOWN: Unknown system interface type [dec].

Explanation The system has detected an unknown system interface type. The system could not find the next valid interface's internal interface number.

Error Message    %NIM-3-UNKNOWN_INTF_TYPE: Unknown Interface type requested.

Explanation An unknown interface type has been requested.

Error Message    %NIM-3-USP_PORT_ERR: Error in USP and/or port registry data.

Explanation An error has occurred in the USP and/or port registry data.

Error Message    %NIM-3-USP_SLOT_ERR: Error in USP and/or SYSTEM_SLOTS registry data.

Explanation An error has occurred in the USP and/or SYSTEM_SLOTS registry data.

Error Message    %NIM-4-ADDR_TYPE_INVALID: Address type [dec] is not valid for 
interface [dec].

Explanation The address type is not valid. It is not a burned-in address or a locally administered address.

Error Message    %NIM-4-LAG_IN_TRANSITION: LAG in transition. switch reboot DUE..!!!

Explanation LAG is in transition. A switch reboot is due.

Error Message    %NIM-4-MCAST_NOT_SET: Multicast appliance flag not set for interface 
[int]([int],[int],[int]) when LAG enabled.

Explanation The multicast appliance flag does not set when LAG is enabled.

Recommended Action No action is required.

Error Message    %NIM-4-NAME_TYPE_INVALID: Name Type [dec] is not valid for interface 
[dec].

Explanation The interface name type is not valid.

Error Message    %NIM-4-POE_STATE_INVALID: PoE State [dec] is not valid for the 
interface [dec].

Explanation The PoE state is not valid. The state is not enabled or disabled.

Error Message    %NIM-4-TRAP_STATE_INVALID: Trap State [dec] is not valid for interface 
[dec].

Explanation The trap state is not valid. It is not enabled or disabled.

Error Message    %NIM-6-LAA_ADDR_INVALID: Locally administered address is not valid for 
interface [dec].

Explanation The locally administered address is not valid. The LSB of the first byte is not zero.

Recommended Action No action is required.

Error Message    %NIM-6-MCAST_STATE_CHANGED: LAG Enabled - changed multicast state of 
interface [int] to ENABLED

Explanation LAG is enabled. The multicast state has changed to the Enabled state.

Recommended Action No action is required.

Error Message    %NIM-6-STACKINTF_NOT_SUPPORTED: Creating Stack Interface currently not 
supported.

Explanation The system has created a stack interface that is currently not supported.

Recommended Action No action is required.

Error Message    %NIM-6-SW_VER_ERR: Software Version Error on config file [chars].

Explanation There is a software version error in the configuration file.

Recommended Action No action is required.

NMSP Messages

This section contains the NMSP messages.

Error Message    %NMSP-3-CERT_AAA_ERR: NMSP: LBS cert AAA Error for [chars]

Explanation NMSP: The controller LBS-SSC AuthList has failed to validate a certificate.

Error Message    %NMSP-3-CONN_LIMIT_EXCEEDED: [chars]: Maximum connection limit of 
[dec] exceeded

Explanation The maximum NMSP connection limit has been exceeded.

Error Message    %NMSP-3-INIT_FAIL: NMSP Task failed to initialize

Explanation The NMSP receive task has failed to initialize and cannot accept incoming NMSP messages.

Error Message    %NMSP-3-INV_CERT_LEN: NMSP: Received invalid peer cert (size [int])

Explanation The system has received a peer certificate that contains no certificate or is too big.

Error Message    %NMSP-3-PEER_CERT_VER_FAIL: NMSP: LBS cert verification failed check

Explanation NMSP: The controller has failed to validate the LBS peer certificate.

Error Message    %NMSP-3-QUEUE_CREATE_FAIL: [chars]: Failed to create messaging Q 
[chars]

Explanation The system has failed to create a messaging queue.

Error Message    %NMSP-3-SOCK_SEL_FAIL_EBADF: [chars]: Select failed with bad file 
descriptor. All sockets closed

Explanation A select failed with a bad file descriptor. All NMSP sockets have been closed.

Error Message    %NMSP-3-TASK_CREATE_FAIL: [chars]: Failed to create [chars]

Explanation The system has failed to create [chars].

NULL Messages

This section contains NULL subsystem (NULL) messages.

Error Message    %NULL-0-SOCKET_CREATE_FAILED: Socket creation failed

Explanation The NULL module has failed to create a particular socket. The traceback along with this message will suggest which socket it was.

OSAPI Messages

This section contains operating system API (OSAPI) messages.

Error Message    %OSAPI-0-COLLECT_TASK_METRICS_FAILED: Unable to gather task metrics. 
[chars].

Explanation The system is unable to gather task metrics.

Error Message    OSAPI-0-CONFIG_NOT_SAVED: Configuration Not Saved. System will now 
restart!

Explanation The configuration has not been saved. The system will now restart.

Error Message    OSAPI-0-CONFIG_SAVED: Configuration Saved. System will now restart.

Explanation The configuration has been saved. The system will now restart.

Recommended Action No action is required.

Error Message    OSAPI-0-HI_MEM_THRESHOLD_CROSSED: Warning! System free memory (%d) 
below high threshold.

Explanation Warning! The system's free memory has fallen below the high threshold.

Error Message    OSAPI-0-HI_MEM_THRESHOLD_RESTORED: Warning! System free memory (%d) 
restored above high threshold.

Explanation Warning! The system's free memory has been restored above a high threshold.

Error Message    OSAPI-0-INTF_SYSCTL_FAILED: The sysctl %s has failed on interface %s. 
error code: %d.

Explanation The sysctl operation has failed on the interface.

Error Message    %OSAPI-0-INVALID_TIMER_HANDLE: Task is using invalid timer handle 
[int]/[int]

Explanation The task is using an invalid timer handle.

Error Message    %OSAPI-0-INVALID_TIMERCB: Invalid timer control block. TcbPtr=[hex].

Explanation The system has detected an invalid timer control block, and a software timer object has failed.

Error Message    OSAPI-0-LICENSE_FL_UPDATE_FAIL: Failed to update Cisco License 
Directory on flash.

Explanation The system has failed to update the Cisco license directory on flash.

Recommended Action No action is required.

Error Message    %OSAPI-0-MEM_ALLOC_FAILED: Failed to allocate memory for [dec] bytes.

Explanation The system has failed to allocate some memory. The system might be out of buffers. This may be temporary problem.

Error Message    %OSAPI-0-MSGQ_CREATE_FAILED: Failed to create the message queue 
object: [chars]. [chars].

Explanation The system has failed to create a message queue object.

Error Message    OSAPI-0-MTD_ERASE_FAIL: Unable to erase a sector at %d on MTD device 
%s.

Explanation The system is unable to erase a sector on the Memory Technology Device (MTD).

Error Message    OSAPI-0-MTD_INFO_FAIL: Unable to get MTD device info on %s.

Explanation The system is unable to get the Memory Technology Device (MTD) information.

Error Message    OSAPI-0-MTD_LOCK_FAIL: Unable to lock MTD device %s.

Explanation The system is unable to lock the Memory Technology Device (MTD).

Error Message    OSAPI-0-MTD_OPEN_FAIL: Unable to open MTD device %s.

Explanation The system is unable to open the Memory Technology Device (MTD).

Error Message    OSAPI-0-MTD_UNLOCK_FAIL: Unable to unlock MTD device %s.

Explanation The system is unable to unlock the Memory Technology Device (MTD).

Error Message    %OSAPI-0-MUTEX_CREATE_FAILED: Failed to create a mutual exclusion 
object. [chars].

Explanation The system has failed to create a mutual exclusion object.

Error Message    %OSAPI-0-RAD_SW_UPGRADE: System has been upgrading Radio SW for more 
than 30 minutes.

Explanation The APs have been downloading software for the last 30 minutes. Either the network is congested or there is a mismatch between the AP image and the controller image.

Error Message    %OSAPI-0-REAPER_START_FAILED: Unable to start the Osapi Reaper. 
[chars].

Explanation The system is unable to start an OSAPI Reaper.

Error Message    %OSAPI-0-REAPWATCHER_START_FAILED: Unable to start the Osapi Reaper 
Watcher. [chars].

Explanation The system is unable to start an OSAPI Reaper Watcher.

Error Message    OSAPI-0-RESETSYSTEM_FAILED: System will not reset as %ssoftware is 
being upgraded.

Explanation Resetting the system when an image download on the controller or an image downloading to the access point could leave the controller or access points with partial images. This problem could affect the state/functioning of the device after a power cycle. The reset of the system is cancelled when a controller or access point is downloading an image.

Error Message    %OSAPI-0-RESET_START_FAILED: Unable to start the System Reset. 
[chars].

Explanation The system is unable to start the system reset task.

Error Message    OSAPI-0-RESET_TRAP_GENERATED: System reset trap message generated.

Explanation A system reset trap message has been generated.

Recommended Action No action is required.

Error Message    OSAPI-0-SAVE_CONFIG_FAILED: Flash write in progress. Cannot save 
config or reset system.

Explanation A Flash write is in progress. The system cannot save the configuration or reset the system.

Error Message    OSAPI-0-SET_ETHERNET_PORT_FAILED: Setting Ethernet Port %s MAC. Could 
not get current flags.

Explanation The Linux (Input Output ConTroL) IOCTL operation has failed on the Ethernet interface.

Error Message    OSAPI-0-SET_ETHERNET_PORT_FAILED_1: Setting Ethernet Port %s MAC. 
Could not bring down port.

Explanation The Linux (Input Output ConTroL) IOCTL operation has failed on the Ethernet interface.

Error Message    OSAPI-0-SET_ETHERNET_PORT_FAILED_2: Error while setting Ethernet Port 
%s MAC..Error No: %d.

Explanation The Linux (Input Output ConTroL) IOCTL operation has failed on the Ethernet interface.

Error Message    OSAPI-0-SET_ETHERNET_PORT_FAILED_3: Error while setting Ethernet Port 
%s flags..Error No: %d.

Explanation The Linux (Input Output ConTroL) IOCTL operation has failed on the Ethernet interface.

Error Message    %OSAPI-0-TASK_CREATE_FAILED: Failed to create the task object: 
[chars]. [chars].

Explanation The system has failed to create a task object.

Error Message    %OSAPI-0-TASK_HUNG: Error! Hung task detected ([chars])! (user [dec]% 
system [dec]%)Reset!.

Explanation The system has detected a hung task.

Error Message    %OSAPI-0-TASK_INVALID_ADDRESS: Invalid task [address] ([address] < msg 
< [address]) (1)

Explanation The system has detected a possibly corrupted task.

Error Message    %OSAPI-2-TASK_PRIORITY_INFO: %s - TaskID %d ('%s') osapi_prio %u 
old_prio %u pthread_prio %d cur_prio %d tickleTimer %u\n

Explanation The sytem has changed the thread priority.

Recommended Action No action is required.

Error Message    %OSAPI-0-TASKLIST_CORRUPTED: Task list corruption detected!!!.

Explanation The system has detected a corrupted task list.

Error Message    %OSAPI-0-TIMERCB_ALLOC_FAILED: Unable to allocate timer control block.

Explanation The system is unable to allocate memory for a software timer control block.

Error Message    %OSAPI-0-TIMERCB_FREELIST_CORRUPTED: Timer control block free list is 
corrupted. Head=[hex],Count=[dec],Mempool Size=[dec].

Explanation The timer control block free list is corrupted.

Error Message    %OSAPI-0-TIMER_CREATE_FAILED: Failed to create a timer.

Explanation The system could not create a software timer object.

Error Message    OSAPI-0-TRAP_START_FAILED: Unable to start the System Trap Reset. %s.

Explanation The system is unable to start the System Trap Reset task.

Error Message    %OSAPI-1-MUTEX_PRIO_CLEAR: == Unlock assert == ([chars]) prio=[dec] 
root=[hex] word[[dec]]=[hex].

Explanation A mutex clear lock failure has occurred.

Error Message    %OSAPI-1-MUTEX_PRIO_SET: ** Lock assert ** ([chars]) prio=[dec] 
root=[hex] [chars]

Explanation A mutex lock priority violation has occurred.

Error Message    %OSAPI-1-MUTEX_PRIO_SET2: ** Lock assert ** ([chars]) prio=[dec] 
root=[hex] word[[dec]]=[hex].

Explanation A mutex lock priority violation 2 has occurred.

Error Message    OSAPI-3-CLOSE_FAILED: Failed to close file

Explanation The system is unable to close a file.

Error Message    %OSAPI-3-FILE_CREATE_FAILED: Failed to create the file : [chars]. 
[chars].

Explanation The system could not create a file or directory. There may be several reasons behind it, including that the system has run out of disk space.

Error Message    %OSAPI-3-FILE_OPEN_FAILED: Failed to open the file : [chars].

Explanation The system could not open a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Error Message    %OSAPI-3-FILE_TRANSFER_ABORTED: Aborting file transfer. [chars].

Explanation The system is aborting a file transfer.

Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.

Error Message    %OSAPI-3-FILE_WRITE_FAILED: Failed to write [dec] bytes to the file : 
[chars] (FileDesc:[dec]). [chars].

Explanation The system could not write to a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Error Message    %OSAPI-3-FILE_WRITENOCLOSE_FAILED: Failed to write [dec] bytes 
(FileDesc:[dec]). [chars].

Explanation The system could not write to a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Error Message    %OSAPI-3-INTF_IOCTL_FAILED: The I/O control operation ([chars]) has 
failed on the interface [chars].IpAddr:[int].[int].[int].[int] Errorcode:[dec]

Explanation The I/O control operation has failed on the interface.

Error Message    %OSAPI-3-INVALID_FILE_HANDLE: The File/Socket handle is Invalid. 
Handle = [dec].

Explanation The file/socket handle is invalid.

Error Message    %OSAPI-3-INVALID_PING_RESPONSE: Ping response from 
[int].[int].[int].[int] is invalid. [chars].

Explanation The ping response is invalid.

Recommended Action This is a debug message only. No action is required.

Error Message    OSAPI-3-IOCTL_FAILED: ioctl ([chars]) failed for interface [chars].

Explanation The system was unable to complete the specified IOCTL operation.

Error Message    %OSAPI-3-KTHREAD_STRUCT_ALLOC_FAILED: We failed to create a struct for 
/proc/[chars]/status

Explanation The system failed to create a structure for storing kthread information.

Error Message    %OSAPI-3-KTHREAD_TABLE_FULL:  Need a bigger osapi_kthread_tbl to store 
kthread [chars] pid=[dec].

Explanation The system needs a bigger osapi_kthread_tbl to store a kthread.

Error Message    %OSAPI-3-LINK_ERROR: Error condition detected on link [chars] (rxp 
[int] rxe [int]; previously rxp [int] rxe [int]

Explanation A link error has been detected on the specified link.

Error Message    %OSAPI-3-OPEN_FAILED: Failed to open file [chars]

Explanation The system is unable to open a file with the given name.

Error Message    %OSAPI-3-PATH_BUILD_FAILED: Failed to build the path string for 
[chars]

Explanation The system has failed to build a path string.

Error Message    %OSAPI-3-PING_OPER_FAILED: Unable to start ICMP ping to host [chars]. 
[chars]

Explanation The system is unable to start an ICMP ping to host.

Error Message    %OSAPI-3-ROUTE_INFO_GET_FAILED: Unable to retrieve routing information

Explanation The system is unable to retrieve routing information, and unable to access /proc/net/route.

Error Message    %OSAPI-3-SOCKET_FAILED: Failed to open socket.

Explanation The system is unable to open a socket.

Error Message    %OSAPI-3-SOCK_OPER_FAILED: The [chars] operation has failed on the 
socket descriptor [dec]. Errorcode:[dec]

Explanation An operation has failed on a socket descriptor.

Error Message    %OSAPI-3-SYSINFO_FAILED: The system API sysinfo() returned failure. 
Error: [chars].

Explanation The system API has returned a failure.

Error Message    %OSAPI-3-TASK_ADD_LOCKED: Exceeded maximum task count [int] (max 
[int])

Explanation The maximum number of tasks that can be created has been exceeded.

Error Message    %OSAPI-3-TASK_GETTIME_FAILED: Failed to retrieve statistics 
(/proc/<pid>/stats) for task '[chars]'

Explanation The system has failed to retrieve statistics (/proc/<pid>/stats) for a task.

Error Message    %OSAPI-3-TASK_RMV_LOCKED: Failed to delete a task 
osapiTaskFreeList.head [address], count [int]

Explanation The system has failed to delete a task.

Error Message    %OSAPI-3-TASK_SET_TICKLE: Task [chars] requesting [dec] second timer. 
Minimum is 20. Setting to 20.

Explanation The requested timer is less than the minimum time allowed. The minimum time is 20. The system is setting the timer to 20.

Error Message    %OSAPI-4-CPU_OVERLOAD: Warning! Task [dec] ([chars]) is taking [dec]% 
([dec]% user [dec]%system)of the cpu!.

Explanation Warning! A task is overloading the CPU.

Error Message    %OSAPI-4-FILE_MOVE_FAILED: Failed to move the file [chars] to [chars].

Explanation The system could not move or rename a file or directory. There may be several reasons behind it, including that the source path provided does not exist.

Error Message    %OSAPI-4-GW_ADD_FAILED: Unable to add the gateway [chars]. System 
command returned failure. Error code:[dec]

Explanation The system is unable to add a gateway. The system command has failed.

Error Message    %OSAPI-4-MSGQ_DUMP_FAILED: Failed to dump the message queue history: 
[chars]. [chars].

Explanation The system has failed to dump the message queue history in the event of a crash.

Error Message    %OSAPI-4-MSGQ_RECV_FAILED: Failed to receive a message from the 
message queue object: [chars]. [chars].

Explanation The system has failed to receive a message from a message queue object.

Error Message    %OSAPI-4-MSGQ_SEND_FAILED: Failed to send a message to the message 
queue object: [chars]. [chars].

Explanation The system has failed to send a message to a message queue object.

Error Message    %OSAPI-4-MUTEX_LOCK_FAILED: Failed to acquire a mutual exclusion 
object. [chars].

Explanation The system has failed to acquire a mutual exclusion object.

Error Message    %OSAPI-4-ROUTE_ADD_FAILED: Unable to add the route (Dest:[chars], 
NetMask:[chars], NextHop:[chars]). System command returned failure. 
Errorcode:[dec]

Explanation The system is unable to add a route. The system command failed.

Error Message    %OSAPI-4-ROUTE_DEL_FAILED: Unable to delete the route (Dest:[chars], 
NetMask:[chars], NextHop:[chars]). System command returned failure. 
Errorcode:[dec]

Explanation The system is unable to delete a route. The system command failed.

Error Message    %OSAPI-4-TIMERTCB_NOT_ALLOCATED: Timer [int]/[int] ('[chars]') 
already destroyed.

Explanation A software timer object is already destroyed and cannot be used.

Error Message    %OSAPI-4-TIMERTCB_REALLOCATED: Timer [int]/[int] ('[chars]') found to 
be destroyed/reallocated.

Explanation The timer is destroyed/reallocated.

Error Message    %OSAPI-4-TIME_SHIFT_DETECTED: Detected [chars] time shift. Last: 
[dec].[dec]. --> Now:[dec].[dec].

Explanation The system has detected a time shift.

Error Message    %OSAPI-5-CLEAN_TASK: Reaper cleaning up exited task '[chars]' 
([address])

Explanation The reaper is cleaning up the exited task.

Recommended Action No action is required.

Error Message    %OSAPI-5-FILE_CLOSE_FAILED: Failed to close the file descriptor: 
[dec].

Explanation The system could not close a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Error Message    %OSAPI-5-FILE_DEL_FAILED: Failed to delete the file : [chars]. 
[chars].

Explanation The system could not delete a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Error Message    %OSAPI-5-FILE_READ_FAILED: Failed to read [dec] bytes from the file : 
[chars] (FileDesc:[dec]). [chars].

Explanation The system could not read from a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Error Message    %OSAPI-5-FILE_READNOCLOSE_FAILED: Failed to read [dec] bytes 
(FileDesc:[dec]). [chars].

Explanation The system could not read from a file or directory. There may be several reasons behind it, including that the path provided does not exist.

Error Message    %OSAPI-5-MSGQ_DEL_FAILED: Failed to delete the message queue object: 
[chars]. [chars].

Explanation The system has failed to delete a message queue object.

Error Message    %OSAPI-5-MUTEX_DEL_FAILED: Failed to delete a mutual exclusion object. 
[chars].

Explanation The system has failed to delete a mutual exclusion object.

Error Message    %OSAPI-5-MUTEX_UNLOCK_FAILED: Failed to release a mutual exclusion 
object. [chars].

Explanation The system has failed to release a mutual exclusion object.

Error Message    %OSAPI-6-FILE_DOES_NOT_EXIST: File : [chars] does not exist.

Explanation The system could not find the file or directory. There may be several reasons behind it, including that certain functionality has never been configured on the system.

Recommended Action

Bias-Free Language

Book Title

Cisco Wireless LAN Controller System Message Guide, Release 7.3

Chapter Title

NIM NMSP NULL and OSAPI System Messages

Results

Chapter: NIM NMSP NULL and OSAPI System Messages

NIM NMSP NULL and OSAPI System Messages

NIM Messages

NMSP Messages

NULL Messages

OSAPI Messages

Was this Document Helpful?

Contact Cisco